AKDY KF0008 Easy-Install Single-Handle Pull-Down Sprayer Kitchen Faucet installation Guide
Add to my manuals15 Pages
advertisement
INSTALLATION MANUAL
Single Handle
Pull-down Kitchen Faucet
KF0007
KF0008
KF0009
KF0010
KF0011
KF0012
Customer Service Phone: 1.888.808.0450
Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Customer Service at
(888)808-0450 for a replacement
• Turn off the cold and hot water at the angle stops and turn on the old faucet to release any built up pressure
• Flush angle stops to release any debris prior to installation
Diagram and Parts List
KF0007 | KF0008 | KF0009
1.
Spray Head
2.
Faucet Body
3.
Hot and Cold Waterlines
A. Cold
B. Hot
4.
Quick Connector
5.
Mounting Hardware
A. Rubber Washer
B. Metal Washer
C. Mounting Nut
D. Mounting Screws
6.
Nylon braided hose
7.
Weight
8.
Cambox
9.
Base O-Ring
Tools you will need
Adjustable Wrench
Silicone Sealant
(optional)
Phillips Screwdriver Safety Goggles
Faucet Installation Procedure
KF0007 | KF0008 | KF0009
Installer Tip:
Shut off main water supply before installing new faucet.
KF0007 | KF0008 | KF0009
Step 1. Faucet installation - without deck plate
Insert Base O-ring.
Step 2. Install faucet and mounting hardware
Insert faucet body (2) into hole in countertop or deck plate assembly. Install mounting hardware (8, 5A, B, C
& D) from underneath the countertop.
Step 3. Secure mounting hardware
KF0007 | KF0008 | KF0009
Adjust direction of faucet body (2) so that handle is on right side of faucet. Tighten mounting nut (5C) until snug.
Tighten mounting screws
(5D) to nut with a Phillips screwdriver until snug.
Step 4. Attach spray hose and counterweight
Connect spray hose (6) to quick connector (4) attached to supply line.
Install weight (7) on lowest vertical point on spray hose (6).
Step 5. Connect waterlines
KF0007 | KF0008 | KF0009
Connect waterlines (3) to angle stops. Tighten both ends of hose with a wrench until snug. Turn on hot and cold angle stops and check for leaks.
NOTE: Make sure filter washers are installed.
Step 6. Flush spray hose
Un-screw spray head (1) from spray hose (6). Hold tip of spray hose (6). Turn faucet on and let the water run for 60 seconds to flush any debris.
Step 7. Check for leaks
KF0007 | KF0008 | KF0009
Check for leaks at the connections. Retighten if necessary.
Diagram and Parts List
KF0010 | KF0011 | KF0012
3B
Diagram and Parts List
1. Spray Head
2. Faucet Body
3. Hot & ColdWaterlines
A.Cold
B.Hot
4.
Nylon braided hose
5. Mounting Hardware
A.Rubber Washer
B.Metal Washer
C.Mounting Nut
D.Mounting Screws
6. Cambox
7.
Base O-Ring
KF0010 | KF0011 | KF0012
Tools you will need
Adjustable Wrench
Silicone Sealant
(optional)
Phillips Screwdriver
Safety Goggles
KF0007 | KF0008 | KF0009
Codes/Standards Applicable:
GREEN LEAD FREE
IAPM
OR&T
TM
Meets ASME A112.18.1M/A112.18.1
1.75GPM 6.6L/min maximum
1.
2.
3.
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
Rinse with clean water & dry with a soft cloth
Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
Do not use cloth with a coarse surface
*This installation manual is subject to change without further notice.
Codes/Standards Applicable:
LEAD FREE
IAPM
OR&T
TM
Meets ASME A112.18.1M/A112.18.1
1.75GPM 6.6L/min maximum
1.
2.
3.
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
Rinse with clean water & dry with a soft cloth
Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
Do not use cloth with a coarse surface
*This installation manual is subject to change without further notice.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project