Design House 547570 Installation guide

Design House 547570 Installation guide
5.
5.
a
2.
2
t
3.
with
3
Notes:The picture in this installation instruction is for reference
only, pls refer to actual product in installation process.
4.
off the hot and cold water line
with
4
Apply plumbers putty to the
underside of the flange (1).Insert
the pop-up body(2) into the sink.
Screw the flange(1) onto the pop
-up body(2). The pivot hole (3)
must face the back of the sink.
Use the groove joint pliers to
tighten the nut(4), but do not over
tighten.Do not turn the pop-up
body(2) while tightening the nut
(4) or the sealant may not seal
property. Clean away any excess
putty.
CARE AND MAINTENANCE
LIMITED LIFETIME WARRANTY
Clean peridodically with a soft cloth.Avoid abraisive cleaners,steel wool, and harsh chemicals as these will dull
the finish and void your warranty
The distributor warrants to the original consumer purchaser this product to be free from defects in material and
workmanship under normal use in residential applications.At its option, the Company will provide repair parts or
replace defective product when the product is used in accordance with the manufacturer's specifications.
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Leaks
underneath
handle
1.Shut off the water supply to the faucet that leaks.
Bonnet has come loose
or O-ring on cartridge is
2.Remove the handle on the problem side. Loosen the bonnet by
dirty or twisted.
turning it counterclockwise. Lift out the cartridge assembly.
3.Inspect the rubber valve seat in the faucet body. If there is debris
or brass scrap on the surface of the seat, remove it. If the rubber
seat is stuck tightly in the water inlet hole, push it gently with a
fingertip so that it moves up and down smoothly. The spring
(smaller end up) must be replaced underneath the valve seat. If
the rubber valve seat is worn out or broken, replace the cartridge
by calling customer service.
4.Replace the cartridge in the faucet body. Make sure that the
ridges on the two sides of the cartridge bonnet fit into the grooves
on the two sides of the faucet body.Tightly screw the bonnet onto
the faucet body.
The distributor provides a limited warranty on the finish of this product to the original purchaser.At its option, the
distributor will provide repair parts or replace defective product when the product is used in accordance with the
manufacturer's specifications.Use of mild abrasive,abrasive or chemical cleaners may damage the finish of the
faucet.We recommend cleaning your faucet with a soft cloth, moistened with water.Damage resulting from the
use of abrasive or chemical cleaners SHALL VOID THIS WARRANTY.
This warranty is not applicable to any products or parts of products where damage is caused by use of nongenuine parts; is due to installation error, product misuse, negligence or faulty maintenance; or where the
product is not installed according to local building codes.
This warranty excludes labor charges or damage incurred during installation, repair or replacement, and any
indirect, incidental or consequential damages, losses, injury or costs of any nature. This warranty is in lieu of
and excludes all other warranties, conditions and guarantees, whether expressed or implied, including without
restriction those of merchantability or fitness of use.Liability under this warranty will not exceed the purchase
price for the product claimed to be defective by the original consumer purchaser. Some states or provinces do
not allow the exclusion or limitation of consequential damages so the above limitations or exclusions may not
apply. This warranty gives you specific legal rights and you may also have other rights which vary from state to
state, or province to province.
Inquiries regarding warranty claims can be directed to 1-800-558-8700,8 a.m. - 5 p.m., CST, Monday - Friday.
5.Re-install the handle.
Water does not Rubber valve seat is
dirty,stuck or broken.
completeply
shut off
1.Shut off the water supply to the faucet that leaks.
2.Remove the handle on the problem side. Loosen the bonnet by
turning it counterclockwise. Lift out the cartridge assembly.
3.Inspect the rubber valve seat in the faucet body. If there is debris
or brass scrap on the surface of the seat, remove it. If the rubber
seat is stuck tightly in the water inlet hole, push it gently with a
fingertip so that it moves up and down smoothly. The spring
(smaller end up) must be replaced underneath the valve seat. If
the rubber valve seat is worn out or broken, replace the cartridge
by calling customer service.
4.Replace the cartridge in the faucet body. Make sure that the
ridges on the two sides of the cartridge bonnet fit into the grooves
on the two sides of the faucet body.Tightly screw the bonnet onto
the faucet body.
5.Re-install the handle.
www.todaysdesignhouse.com
3
www.todaysdesignhouse.com
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement