Canister Vacuum Cleaner
Q u i e t & P o w e r f u l
User Guide
TABLE OF CONTENTS
COMPONENTS....................................................................... 5
USE AND FUNCTION.............................................................. 6
VARIABLE SUCTION CONTROL ............................................. 6
MOTOR THERMOSTAT........................................................... 7
CHANGE DUST BAG............................................................... 7
CARRY AND MOVE AWAY THE CLEANER.............................. 7
HOW REMOVING, CLEANING OR REPLACING
PRE-MOTOR FILTER AND HEPA FILTER ........................... 8 - 9
BASIC TECHNICAL DATA ..................................................... 10
DISPOSAL THE UNIT........................................................... 10
SILENZIO - 2 User Guide
SAFETY PRECAUTIONS
For household use only!
When using your vacuum, basic safety precautions should always be observed, including the following
1. Do not leave vacuum cleaner unattended when it is plugged in. Unplug from outlet when not in use and before pulling filters out.
2. To reduce the risk of electric shock, do not use outdoors or on wet surfaces.
3. Do not allow children to use as a toy. Close attention is necessary when used near children.
4. Use only as described in this manual. Use only manufacturer’s recommended attachments.
5. Do not use with damaged cord or plug. Do not use vacuum cleaner if it has been dropped, damaged , left outdoor , or dropped into water. Return appliance to the appliance customer service for examination repair or adjustment.
6. Do not pull or carry by cord. Do not use the cord as a handle, close the door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not unplug by pulling on cord. To unplug, grasp by the plug, not the cord.
8. Do not handle plug or vacuum cleaner with wet hands. Dot not use outdoors or on wet surfaces.
9. Do not put any objects into openings. Do not use with any openings blocked and do not restrict airflow. Keep all opening free of dust, lint, hair, and anything that may reduce airflow.
10. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
11. Do not pick up hard or sharp objects such as glass nails, screws, coins, etc.
12. Do not pick up hot coals, cigarette, matches or any hot, smoking, or burning objects.
13. Do not use without filters in place.
14. Turn off all controls before plugging or unplugging vacuum cleaner.
15. Use extra care when vacuuming on stairs.
16. Do not pick up flammable or combustible materials (lighter fluid, gasoline, etc.) or use in the presence of explosive liquids or vapor.
17. Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.)
18. Do not use in an enclosed space filled with vapors given off by oil based paints, paint thinner, moth proofing, flammable dust, or other explosive or toxic vapors.
19. Always unplug this appliance before connecting or disconnecting vacuum hose. Do not allow plug to whip when rewinding.
20. Use only on dry, indoor surfaces.
21. Do not use for any purpose other than described in this user’s guide.
22. Store your appliance indoor in a cool, dry area.
23. Keep your work area well dry.
24. Do not immerse the vacuum into water or other liquids.
25. Keep end of hose, wands and other openings away from your face and body.
26. Do not use the cleaner to clean your pets or any animal.
27. Keep the head (eyes, ear, mouth, etc.) away from the openings, when the cleaner is working or plugging.
SILENZIO - 3 -
User Guide
SAFETY PRECAUTIONS
Safety of particular groups of people
1. This appliance may only be used by children over the age of 8 and by persons with reduced physical, sensory or mental capacities or a lack of experience and/or knowledge when they are supervised or if they have been instructed about the safe use of the appliance and have understood the risks resulting from the use of the appliance.
2. Children may not play with the appliance or stand or sit on the appliance. Cleaning and user maintenance may not be performed by children without supervision.
3. Keep children younger than 8 away from the appliance and power cable.
4. Keep packaging materials out of the reach of children and dispose of them. Otherwise they present a suffocation risk.
WARNING:
Important
If the suction opening of the unit, the hose or the tube is blocked, switch off the vacuum cleaner and remove the blocking substance before you start the unit again.
1. Do not operate the vacuum cleaner too close to heater or radiators.
2. Before inserting the power plug into the wall outlet, make sure that your hands are dry.
3. Before you start the unit, make sure to remove large or sharp objects that might damage the dust tank and hose.
4. When pulling out the power plug from the wall outlet, pull the plug not the power cord.
5. Do not use without all filters in place.
6. When using, if you hear of squeak from the cleaner, it must be suction appears to be reduced, you must stop (make sure the cleaner is not plugged), then clean the all air filters.
7. If the supply cord is damaged, or replaced by manufacturer, service agent or similarly qualified person in order to avoid a hazard.
8. Hold the plug when rewinding the power cord. Do not let the cord loose since it could cause harm.
SILENZIO - 4 -
User Guide
1
COMPONENTS
2
6
7
3
4
8
5
9
10 11
SILENZIO
2. TURBO AIR BRUSH
3. FLOOR BRUSH
4. UPHOLSTERY AND DUSTING BRUSH
5. CREVICE TOOL
6. HEPA BAG
7. HANGER ON WAND
9. TELESCOPIC METAL WAND
10. HEPA FILTER
11. MOTOR FILTER
- 5 User Guide
PLEASE NOTE:
The sponge filter material in the cleaner will became dusty over time. This is normal and will not affect the performance of the filter. If the sponge filter is so dusty that suction does not return to
100%, then we suggest that the motor filter be removed then and rinsed under the faucet and allowed to dry for 24 hours by airing not near the fire or some high temperature objects before refitting into the vacuum. This should be done once every six months or when suction appears to be reduced.
It is recommended to change the HEPA filter once a year or as soon as it is damaged.
IMPORTANT:
The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.
IMPORTANT:
This motor is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur unplug the vacuum cleaner from the wall outlet and turn off switch, change dust bag and clean filters. Allow the unit to cool for approximately 1 hour. To restart, replug into wall outlet and turn switch back on.
CHANGE DUST BAG
1. Open the front cover.
2. Change dust bag.
3. Be carefult not to throw away the bag holder at the same time, it will be needed when installing the new bag.
REMOVING & CLEANING PRE-MOTOR FILTER
AND AIR OUTLET FILTER
WARNING:
Always unplug the unit from electrical outlet before getting out the dust barrel.
A. Pre-motor filter
1. Open the front cover.
2. Clean or change filter.
1
B. HEPA filter
1. Open the front cover.
2. Take out the air outlet filter to clean or change.
2
1 2 3
CARRY AND MOVE AWAY THE CLEANER
NOTE:
This cleaner have a special feature for handle. The carry-handle is in front. You can use it to conveniently carry the cleaner in a vertical position.
1 2
PLEASE NOTE:
The sponge filter material in the cleaner will became dusty over time. This is normal and will not affect the performance of the filter. If the sponge filter is so dusty that suction does not return to
100%, then we suggest that the motor filter be removed then and rinsed under the faucet and allowed to dry for 24 hours by airing not near the fire or some high temperature objects before refitting into the vacuum. This should be done once every six months or when suction appears to be reduced.
It is recommended to change the HEPA filter once a year or as soon as it is damaged.
IMPORTANT:
The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.
USE AND FUNCTION
Assembling vacuum cleaner
NOTE :
Always remove the power plug from the wall outlet before assembling or removing accessories.
1. Attaching the Flexible Hose into the vacuum: connect the flexible hose into the air intake duct, push in until you hear a “click”, indicating it is in its locked position.
IMPORTANT:
This motor is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur unplug the vacuum cleaner from the wall outlet and turn off switch, change dust bag and clean filters. Allow the unit to cool for approximately 1 hour. To restart, replug into wall outlet and turn switch back on.
CHANGE DUST BAG
1. Open the front cover.
2. Change dust bag.
3. Be carefult not to throw away the bag holder at the same time, it will be needed when installing the new bag.
2. Fitting the tube to the curved wand/hose extension: push the tube into the curved wand/hose extension.
3. Fitting the Floor Brush to the tube: push the tube into the floor brush. Adjust the tube to the desired length.
VARIABLE SUCTION CONTROL
NOTE :
Once all attachments are in place, unwind a sufficient length of cable and insert the plug into the wall outlet. A yellow mark on the power cord shows the MAXIMUM cable length. Do not pull the power cord beyond the red mark.
1. Insert the power plug into the wall outlet.
2. Press the power on/off button located the unit to turn the vacuum cleaner
“ON”.
3. To rewind the power cord, press the cord rewind button with one hand and guide the power cord with the other hand to ensure that it does not whip causing damage or injury.
4. To adjust the suction, turning the
On/off button on the suction hand to control the suction power of the vacuum cleaner.
ON / OFF
BUTTON
SPEED CONTROL BUTTON
REWIND
BUTTON
SILENZIO - 6 User Guide
1 2 3
CARRY AND MOVE AWAY THE CLEANER
NOTE:
This cleaner have a special feature for handle. The carry-handle is in front. You can use it to conveniently carry the cleaner in a vertical position.
REMOVING & CLEANING PRE-MOTOR FILTER
AND AIR OUTLET FILTER
WARNING:
Always unplug the unit from electrical outlet before getting out the dust barrel.
A. Pre-motor filter
1. Open the front cover.
2. Clean or change filter.
1
B. HEPA filter
1. Open the front cover.
2. Take out the air outlet filter to clean or change.
2
1 2
PLEASE NOTE:
The sponge filter material in the cleaner will became dusty over time. This is normal and will not affect the performance of the filter. If the sponge filter is so dusty that suction does not return to
100%, then we suggest that the motor filter be removed then and rinsed under the faucet and allowed to dry for 24 hours by airing not near the fire or some high temperature objects before refitting into the vacuum. This should be done once every six months or when suction appears to be reduced.
It is recommended to change the HEPA filter once a year or as soon as it is damaged.
IMPORTANT:
The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.
MOTOR THERMOSTAT
IMPORTANT:
This motor is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur unplug the vacuum cleaner from the wall outlet and turn off switch, change dust bag and clean filters. Allow the unit to cool for approximately 1 hour. To restart, replug into wall outlet and turn switch back on.
CHANGE DUST BAG
1. Open the front cover.
2. Change dust bag.
3. Be carefult not to throw away the bag holder at the same time, it will be needed when installing the new bag.
REMOVING & CLEANING PRE-MOTOR FILTER
AND AIR OUTLET FILTER
WARNING:
Always unplug the unit from electrical outlet before getting out the dust barrel.
A. Pre-motor filter
1. Open the front cover.
2. Clean or change filter.
1
B. HEPA filter
1. Open the front cover.
2. Take out the air outlet filter to clean or change.
2
1 2 3
CARRY AND MOVE AWAY THE CLEANER
NOTE:
This cleaner have a special feature for handle. The carry-handle is in front. You can use it to conveniently carry the cleaner in a vertical position.
1 2
SILENZIO - 7 User Guide
PLEASE NOTE:
The sponge filter material in the cleaner will became dusty over time. This is normal and will not affect the performance of the filter. If the sponge filter is so dusty that suction does not return to
100%, then we suggest that the motor filter be removed then and rinsed under the faucet and allowed to dry for 24 hours by airing not near the fire or some high temperature objects before refitting into the vacuum. This should be done once every six months or when suction appears to be reduced.
It is recommended to change the HEPA filter once a year or as soon as it is damaged.
IMPORTANT:
The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.
IMPORTANT:
This motor is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur unplug the vacuum cleaner from the wall outlet and turn off switch, change dust bag and clean filters. Allow the unit to cool for approximately 1 hour. To restart, replug into wall outlet and turn switch back on.
CHANGE DUST BAG
1. Open the front cover.
2. Change dust bag.
3. Be carefult not to throw away the bag holder at the same time, it will be needed when installing the new bag.
REMOVING & CLEANING PRE-MOTOR FILTER
AND AIR OUTLET FILTER
WARNING:
Always unplug the unit from electrical outlet before getting out the dust barrel.
A. Pre-motor filter
1. Open the front cover.
2. Clean or change filter.
1
B. HEPA filter
1. Open the front cover.
2. Take out the air outlet filter to clean or change.
2
1 2 3
CARRY AND MOVE AWAY THE CLEANER
NOTE:
This cleaner have a special feature for handle. The carry-handle is in front. You can use it to conveniently carry the cleaner in a vertical position.
1 2
SILENZIO - 8 User Guide
PLEASE NOTE:
The sponge filter material in the cleaner will became dusty over time. This is normal and will not affect the performance of the filter. If the sponge filter is so dusty that suction does not return to
100%, then we suggest that the motor filter be removed then and rinsed under the faucet and allowed to dry for 24 hours by airing not near the fire or some high temperature objects before refitting into the vacuum. This should be done once every six months or when suction appears to be reduced.
It is recommended to change the HEPA filter once a year or as soon as it is damaged.
IMPORTANT:
The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.
SILENZIO - 9 User Guide
IMPORTANT:
This motor is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur unplug the vacuum cleaner from the wall outlet and turn off switch, change dust bag and clean filters. Allow the unit to cool for approximately 1 hour. To restart, replug into wall outlet and turn switch back on.
CHANGE DUST BAG
1. Open the front cover.
2. Change dust bag.
3. Be carefult not to throw away the bag holder at the same time, it will be needed when installing the new bag.
REMOVING & CLEANING PRE-MOTOR FILTER
AND AIR OUTLET FILTER
WARNING:
Always unplug the unit from electrical outlet before getting out the dust barrel.
A. Pre-motor filter
1. Open the front cover.
2. Clean or change filter.
1
B. HEPA filter
1. Open the front cover.
2. Take out the air outlet filter to clean or change.
2
1 2 3
CARRY AND MOVE AWAY THE CLEANER
NOTE:
This cleaner have a special feature for handle. The carry-handle is in front. You can use it to conveniently carry the cleaner in a vertical position.
1 2
PLEASE NOTE:
The sponge filter material in the cleaner will became dusty over time. This is normal and will not affect the performance of the filter. If the sponge filter is so dusty that suction does not return to
100%, then we suggest that the motor filter be removed then and rinsed under the faucet and allowed to dry for 24 hours by airing not near the fire or some high temperature objects before refitting into the vacuum. This should be done once every six months or when suction appears to be reduced.
It is recommended to change the HEPA filter once a year or as soon as it is damaged.
IMPORTANT:
The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.
BASIC TECHNICAL DATA
Model: SILENZIO
Voltage: 120 V, 60 HZ, 10 A - 1 2 00 W
DISPOSAL THE UNIT
APPLIANCES THAT ARE MARKED WITH THIS SYMBOL MUST BE DISPOSED OF SEPARATELY FROM
HOUSEHOLD GARBAGE. THESE APPLIANCES CONTAIN VALUABLE RAW MATERIALS THAT CAN BE
RECYCLED. PROPER DISPOSAL PROTECTS THE ENVIRONMENT AND THE HEALTH OF YOUR
FELLOW MEN. YOUR COMMUNITY GOVERNMENT OR YOUR DEALER CAN PROVIDE INFORMATION
ABOUT PROPER DISPOSAL.
SILENZIO - 10 User Guide
IMPORTANT:
This motor is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur unplug the vacuum cleaner from the wall outlet and turn off switch, change dust bag and clean filters. Allow the unit to cool for approximately 1 hour. To restart, replug into wall outlet and turn switch back on.
CHANGE DUST BAG
1. Open the front cover.
2. Change dust bag.
3. Be carefult not to throw away the bag holder at the same time, it will be needed when installing the new bag.
REMOVING & CLEANING PRE-MOTOR FILTER
AND AIR OUTLET FILTER
WARNING:
Always unplug the unit from electrical outlet before getting out the dust barrel.
A. Pre-motor filter
1. Open the front cover.
2. Clean or change filter.
1
B. HEPA filter
1. Open the front cover.
2. Take out the air outlet filter to clean or change.
2
1 2 3
CARRY AND MOVE AWAY THE CLEANER
NOTE:
This cleaner have a special feature for handle. The carry-handle is in front. You can use it to conveniently carry the cleaner in a vertical position.
1 2
PLEASE NOTE:
The sponge filter material in the cleaner will became dusty over time. This is normal and will not affect the performance of the filter. If the sponge filter is so dusty that suction does not return to
100%, then we suggest that the motor filter be removed then and rinsed under the faucet and allowed to dry for 24 hours by airing not near the fire or some high temperature objects before refitting into the vacuum. This should be done once every six months or when suction appears to be reduced.
It is recommended to change the HEPA filter once a year or as soon as it is damaged.
IMPORTANT:
The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.
IMPORTANT:
This motor is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur unplug the vacuum cleaner from the wall outlet and turn off switch, change dust bag and clean filters. Allow the unit to cool for approximately 1 hour. To restart, replug into wall outlet and turn switch back on.
CHANGE DUST BAG
1. Open the front cover.
2. Change dust bag.
3. Be carefult not to throw away the bag holder at the same time, it will be needed when installing the new bag.
REMOVING & CLEANING PRE-MOTOR FILTER
AND AIR OUTLET FILTER
WARNING:
Always unplug the unit from electrical outlet before getting out the dust barrel.
A. Pre-motor filter
1. Open the front cover.
2. Clean or change filter.
1
B. HEPA filter
1. Open the front cover.
2. Take out the air outlet filter to clean or change.
2
1 2 3
CARRY AND MOVE AWAY THE CLEANER
NOTE:
This cleaner have a special feature for handle. The carry-handle is in front. You can use it to conveniently carry the cleaner in a vertical position.
1 2
PLEASE NOTE:
The sponge filter material in the cleaner will became dusty over time. This is normal and will not affect the performance of the filter. If the sponge filter is so dusty that suction does not return to
100%, then we suggest that the motor filter be removed then and rinsed under the faucet and allowed to dry for 24 hours by airing not near the fire or some high temperature objects before refitting into the vacuum. This should be done once every six months or when suction appears to be reduced.
It is recommended to change the HEPA filter once a year or as soon as it is damaged.
IMPORTANT:
The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.
IMPORTANT:
This motor is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur unplug the vacuum cleaner from the wall outlet and turn off switch, change dust bag and clean filters. Allow the unit to cool for approximately 1 hour. To restart, replug into wall outlet and turn switch back on.
CHANGE DUST BAG
1. Open the front cover.
2. Change dust bag.
3. Be carefult not to throw away the bag holder at the same time, it will be needed when installing the new bag.
REMOVING & CLEANING PRE-MOTOR FILTER
AND AIR OUTLET FILTER
WARNING:
Always unplug the unit from electrical outlet before getting out the dust barrel.
A. Pre-motor filter
1. Open the front cover.
2. Clean or change filter.
1
B. HEPA filter
1. Open the front cover.
2. Take out the air outlet filter to clean or change.
2
1 2 3
CARRY AND MOVE AWAY THE CLEANER
NOTE:
This cleaner have a special feature for handle. The carry-handle is in front. You can use it to conveniently carry the cleaner in a vertical position.
1 2
Residential and commercial vacuum cleaner specialist
FOR
PARTS, ACCESSORIES & VACUUM BAGS
VISIT OUR WEBSITE AT
WWW.JOHNNYVAC.COM
CONGRATULATIONS & THANK YOU for having chosen one of our product.
Do not return the unit to the retailer before having spoken with us.
Our most precious wish is that you really love your vacuum cleaner!
In case of problems, contact our experts at 1 800 361-2043 or by email at [email protected]
