American Standard 7052121.278 Delancey Bathroom Faucet Installation instructions
Add to my manuals3 Pages
advertisement
Delancey
®
INSTALLATION
INSTRUCTIONS
7052121
7052124
Single Control Lavatory Faucet
Thank you for selecting American Standard...
the benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
RECOMMENDED TOOLS
Adjustable Wrench
Plumbers' Putty or Caulking
1
INSTALL LAVATORY FAUCET CAUTION
• Seat SEAL (1) into groove in under side of ESCUTCHEON BASE (2) .
• Seat ESCUTCHEON BASE (2) with collar facing up into groove in faucet base.
• Feed FAUCET SUPPLIES (3) and MOUNTING SHANK (4) through hole in mounting surface.
• From below, install GASKET (5) and MOUNTING NUT (6) onto
SHANK (4) . Secure Faucet with MOUNTING NUT (6) . Before final tightening, adjust Faucet so that it is centered. Tighten MOUNTING
NUT (6) to complete faucet mounting.
Regular Screwdriver
Phillips Screwdriver
Certified to comply with ANSI A112.18.1M
Channel Locks
1
4
2
GROOVE IN
(FAUCET BASE)
MOUNTING
SURFACE
5
6
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018 - 1 -
3
M965991 (10/18)
2
MAKE WATER SUPPLY CONNECTIONS
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on fitting supplies are 3/8" compression.
Connect left supply to Hot and right supply to the Cold wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
• Faucet supplies are 28" long from faucet base.
Note: If additional supply length is required, installer must purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are too long, loop as illustrated to avoid kinking.
Figure A.
28"
HOT
2
LOOP SUPPLIES
IF REQUIRED
COLD
1
Figure A.
HOT
COLD
3
DRAIN INSTALLATION
• Install DRAIN (1) by dropping it from the top of the sink.
• From under side of SINK install GASKET (2) and
MOUNTING NUT (3) .
Note: Plumber’s putty or caulk is recommended.
• Thread TAIL PIECE NUT (4) clockwise onto
DRAIN BODY (2) .
• Check DRAIN FLANGE in SINK to ensure that
FOAM GASKET (3) is fully compressed and not visible.
• Operate DRAIN (1) to verify that it opens and closes.
- 2 -
1
PUTTY
4
2
3
M965991 (10/18)
4
TEST INSTALLED FAUCET AND CHECK
FOR LEAKS
• With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
• Remove AERATOR (3) .
• Operate HANDLE (1) to flush water lines thoroughly.
• Replace AERATOR (3) .
3
HOT
OFF
ON
COLD
1
HOT
COLD
2
5
SERVICE
CAUTION
• To remove or replace cartridge:
– Turn valve to OFF position.
– Remove HANDLE SCREW (2) .
– Pull off HANDLE (3) and CAP (4) .
– Unthread CARTRIDGE NUT (5) and remove.
– Pull out CARTRIDGE (6) .
– Inspect CARTRIDGE (6) for debris and clean
if necessary.
– Clean MANIFOLD (1) and rinse clean.
– Reinstall CARTRIDGE (6) onto MANIFOLD (1) .
– Reinstall CARTRIDGE NUT (5) , CAP (4) and
HANDLE ASSEMBLY (3) .
• If spout drips, operate handle several times from
OFF to ON and HOT to COLD position. Do not force - handle turns only 90˚.
6
5 4 3
1
2
2.5mm HEX KEY
6
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
- 3 -
M965991 (10/18)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project