advertisement
www.tattletale.com
6269 Frost Road. Westerville OH 43082
MOTION
GUIDE
MOTION DETECTOR SENSOR
1] learn it in
Remove screw on bottom of
Sensor and remove backplate
Access the Home Screen on your tattletale Consumer Unit.
1] press Settings
2] enter Primary PIN
3] press Advanced
4] press Sensors
5] press Add Sensor
It will ask for your sensor to be placed in “learn mode”.
6] Press and hold on
tamper switch note: The Consumer Unit will sound to indicate sensor has been learned in successfully
2] set it up
[ Tamper Switch ]
Walk Test
Place supplied magnet over arrow on left side of sensor, then remove (LED light indicates detection)
Walk out coverage area making sure the LED flashes for every movement. Test lasts for 1 minute
NOTE: allow a 3 second delay between flashes.
Sensor is set to Interior Delay by default.
[
1] set Name: setting a specific name & location seperates sensors
2] set Type: instant or delay use instant only if sensor will not be tripped during
Entry/Exit to disarm system while in Away mode
]
3] allow Bypass: determines whether it can be bypassed during arming cycle
3] mount it
Standard Corner or Wall Mounting.
[
Refer to Figures on right for bracket mounting
]
1] avoid these Locations: direct sunlight, rapid temperature change, air ducts, metal wall
2] Corner Mounting:
Sensor can be mounted on
Remove Backplate from
Sensor. Use either 2 upper or
2 lower screw holes. Mount height at 7.5 ft. Attach
Sensor on Backplate
3] Wall Mounting: corner or wall, or ceiling using supplied brackets
Remove Backplate. Use 2 screw holes in center. Mount height at 7.5 ft. Attach
Sensor on Backplate
1 ]
2 ]
3 ]
4 ]
5 ]
Screw part A to part B using small screw.
part B insert
Select either the
Corner Mount [ D ] or
Wall Mount [ C ].
Mount selected bracket at a height of
7.5 ft. on the wall using supplied long screws with anchors.
Place the assembly of parts A and B on the shaft of the desired mounting bracket.
[ A ]
Backplate
[ B ]
Mounting Bracket
Wall Mount
Screw Holes
Place on part D or E’s
Mounting Shaft
Insert screw on top of shaft to hold bracket in place.
[ see figure to right ]
6 ]
Attach the sensor to mounted backplate with the screw at the bottom to secure.
[ C ]
Wall Mount
NOTE:
After the Sensor trips (sensing motion) it will not trip again for 3 minutes
During normal operation, the LED will never illuminate. The LED only illuminates in test mode
[ D ]
Corner Mount
Corner
Mount
Screw
Holes backplate insert screw here backplate insert
Screw on top of part C or D after part B has been inserted on top
MOTION DETECTOR SENSOR
1] learn it in
Remove screw on bottom of
Sensor and remove backplate
Access the Home Screen on your tattletale Consumer Unit.
1] press Settings
2] enter Primary PIN
3] press Advanced
4] press Sensors
5] press Add Sensor
It will ask for your sensor to be placed in “learn mode”.
6] Press and hold on
tamper switch note: The Consumer Unit will sound to indicate sensor has been learned in successfully
2] set it up
[ Tamper Switch ]
Walk Test
Place supplied magnet over arrow on left side of sensor, then remove (LED light indicates detection)
Walk out coverage area making sure the LED flashes for every movement. Test lasts for 1 minute
NOTE: allow a 3 second delay between flashes.
Sensor is set to Interior Delay by default.
[
1] set Name: setting a specific name & location seperates sensors
2] set Type: instant or delay use instant only if sensor will not be tripped during
Entry/Exit to disarm system while in Away mode
]
3] allow Bypass: determines whether it can be bypassed during arming cycle
3] mount it
Standard Corner or Wall Mounting.
[
Refer to Figures on right for bracket mounting
]
1] avoid these Locations: direct sunlight, rapid temperature change, air ducts, metal wall
2] Corner Mounting:
Sensor can be mounted on
Remove Backplate from
Sensor. Use either 2 upper or
2 lower screw holes. Mount height at 7.5 ft. Attach
Sensor on Backplate
3] Wall Mounting: corner or wall, or ceiling using supplied brackets
Remove Backplate. Use 2 screw holes in center. Mount height at 7.5 ft. Attach
Sensor on Backplate
1 ]
2 ]
3 ]
4 ]
5 ]
Screw part A to part B using small screw.
part B insert
Select either the
Corner Mount [ D ] or
Wall Mount [ C ].
Mount selected bracket at a height of
7.5 ft. on the wall using supplied long screws with anchors.
Place the assembly of parts A and B on the shaft of the desired mounting bracket.
[ A ]
Backplate
[ B ]
Mounting Bracket
Wall Mount
Screw Holes
Place on part D or E’s
Mounting Shaft
Insert screw on top of shaft to hold bracket in place.
[ see figure to right ]
6 ]
Attach the sensor to mounted backplate with the screw at the bottom to secure.
[ C ]
Wall Mount
NOTE:
After the Sensor trips (sensing motion) it will not trip again for 3 minutes
During normal operation, the LED will never illuminate. The LED only illuminates in test mode
[ D ]
Corner Mount
Corner
Mount
Screw
Holes backplate insert screw here backplate insert
Screw on top of part C or D after part B has been inserted on top
www.tattletale.com
6269 Frost Road. Westerville OH 43082
MOTION
GUIDE
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project