Rust-Oleum EpoxyShield 262245 User manual

Rust-Oleum EpoxyShield 262245 User manual
TECHNICAL DATA
ESH-16
EPOXYSHIELD®®
BLACKTOP FILLER SEALER
DESCRIPTION AND USES
.
.PRODUCT APPLICATION (cont.)
EpoxyShield Blacktop Filler Sealer is a single component,
water-based coating made with recycled rubber tires designed
for residential asphalt driveways. This product is designed to
revitalize and protect worn and faded asphalt driveways to likenew condition with a jet black appearance. This product features
excellent color retention and chemical resistance to de-icing salts,
gasoline, oil, and other automotive chemicals. This product
contains no coal tar or asphalt.
.PRODUCTS
SKU
262245
Apply only when air, material, and surface temperatures are
between 50-90°F (10-32°C) and the surface temperature should
not exceed 100°F (38°C). No rain should be forecasted for 48
hours. Stir coating thoroughly to re-disperse any settled pigment.
(Optional: Use brush to trim edges of the driveway before
applying to entire surface). Pour out ½ of the container and work
the product across the blacktop using an 18-24" floor or driveway
squeegee.
Avoid applying coating is direct sunlight. If pavement is extremely
hot, apply a fine water mist to the coating surface and brush out
any remaining water puddles.
Coverage range is based on proper application. Coverage
will vary depending on the condition of the asphalt surface and
will ultimately depend on the pavement porosity. Extreme porous
pavement may significantly reduce product coverage. Application
that is too thick may result in peeling. For asphalt in poor
condition, a 2-coat application will improve uniform look and
appearance. Do not mix or blend this product with any other
driveway coating product. Do not dilute.
.
Description
Jet Black
.PACKAGING
.
3.5 Gallon pail
.PRODUCT APPLICATION
.
APPLICATION
®
.
SURFACE PREPARATION
To ensure proper adhesion and promote maximum service life,
clean the entire driveway surface making sure it is free of dirt,
debris, oil, and grease. Trim any grass or weeds overgrowing
onto the driveway. Clean out all cracks and holes using a
screwdriver or wire brush. Remove any remaining dirt and debris
by sweeping with a stiff bristled broom. Clean heavy grease and
oil spots with EpoxyShield Blacktop Cleaner & Degreaser (sold
separately). Thoroughly rinse entire driveway with fresh water
and allow the surface to dry before application.
Repair major cracks and/or holes in the surface prior to coating
with EpoxyShield Patch & Crack Filler (sold separately). Follow
instructions on the package. Trowel patch & crack filler into small
holes up to 1" deep or pour into cracks up to ½" wide.
Note: Newly paved asphalt surfaces must be allowed to cure for
a minimum of six months or a full summer’s season prior to
application of any coating.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN YOUNG CHILDREN. PREGNANT
WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a
NIOSH-approved respirator to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you start,
find out how to protect yourself and your family by contacting the
National Lead Information Hotline at 1-800-424-LEAD or log on
to www.epa.gov/lead.
DRY & RECOAT TIMES
Dry and recoat times are based on 70°F and 50% relative
humidity. Allow more time at cooler temperatures. Surface
should be ready for foot traffic in 1 hour. The surface will be drive
ready in 4 hours.
CLEAN-UP
Wash tools and equipment with warm water and a mild
detergent immediately after use. Clean up drips or spatters
IMMEDIATELY with water as dried material is very difficult to
remove. Dispose of container and/or unused contents in
accordance with local, state, and federal regulations. Protect
from freezing.
1
Form: GDH-401
Rev.: 080414
TECHNICAL DATA
EPOXYSHIELD® BLACKTOP FILLER SEALER
PHYSICAL PROPERTIES
.
BLACKTOP FILLER SEALER
Resin Type
Acrylic
Pigment Type
Carbon Black, Mineral Fibers
Solvents
Weight
Solids
Propylene Glycol, Water
Per Gallon
12.5 lbs.
Per Liter
1.50 kg
By Weight
65.5%
By Volume
49.0%
Volatile Organic Compounds
<100 g/l (0.83 lbs./gal.)
Recommended Dry Film
Thickness (DFT) Per Coat
Conditional with squeegee and surface condition
Wet Film to Achieve DFT
(Unthinned Material)
Conditional with squeegee and surface condition
Theoretical Coverage at
1 mil DFT (25µ)
786 sq.ft./gal.
(19.3 m2/l)
Practical Coverage at Recommended DFT
(assumes 15% material loss)
Dry Times at 70-80°F
(21-27°C) and 50%
Relative Humidity
Up to 350 sq.ft./pail (8.6 m2/l)
Walk Ready
1 hour
Drive Ready
4 hours
Shelf Life
3 years
Flash Point
>200°F (93°C)
Safety Information
For additional information, see MSDS
Calculated values are shown and may vary slightly from the actual manufactured material
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature
do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we
can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All
technical information is subject to change without notice.
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, Illinois 60061
An RPM Company
Phone: 877•385•8155
www.rustoleum.com
Form: GDH-401
Rev.: 080414
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement