American Standard 3749000.002 Townsend 30 in. Washstand Towel Bar Specification

TOWNSEND ®

PEDESTAL SINK and OPTIONAL FURNITURE

FINE FIRECLAY

TOWNSEND ® PEDESTAL SINK and OPTIONAL FURNITURE

Pedestal Sink and Leg Combinations:

❏ 0328.800 Faucet holes on 8" (203mm) centers (Illustrated)

❏ 0328.400 Faucet holes on 4" (102mm) centers

❏ 0328.100 Center hole only

• Fine fireclay

• Classic styled rectangular pedestal lavatory

• Rear overflow

• Supplied with mounting kit

• Right Height ® for greater comfort during use

• Faucet ledge with large deck area (faucet not included)

• Pedestal tops can also be used with design matched vanity or washstand furniture

• Design coordinates with Townsend ® Collection

Townsend pedestal combination 0328.800

Bowl Size:

19" (485mm) wide,

12-3/4" (324mm) front to back,

5" (128mm) deep

Nominal Dimensions:

Pedestal Sink and Leg Combinations:

30" x 19-1/2" x 35-1/4" (762 x 495 x 895mm)

Pedestal Sink and Furniture Combinations:

30" x 19-1/2" x 35-7/8" (762 x 495 x 910mm)

❏ 0328.008 Pedestal top-8" (203mm) centers

❏ 0328.004 Pedestal top-4" (102mm) centers

❏ 0328.001 Pedestal top-center hole only

❏ 0039.001 Pedestal leg only

❏ 9036.030 30" (762mm) vanity less drawer pulls

❏ 7760.000 Drawer pulls (set of 2) for 30" (762mm) vanity

❏ 9039.030 30" (762mm) washstand less towel bar

❏ 3749.000 Towel bar for 30" (762mm) washstand

❏ 7720.018 Optional decorative p-trap drain

Compliance Certifications -

Meets or Exceeds the Following Specifications:

• ASME A112.19.2/CSA B45.1

Townsend pedestal top sink 0328.008

shown with 9036.030 vanity and 7760.000 drawer pulls

SEE REVERSE FOR ROUGHING-IN DIMENSIONS

To Be Specified:

❏ Chinaware Color: ❏ White ❏ Linen

❏ Vanity Finish: ❏ White ❏ Smoked Grey

❏ Vanity Drawer Pulls Finish: ❏ Chrome ❏ Brushed Nickel

❏ Washstand Finish: ❏ White ❏ Smoked Grey

❏ Washstand Towel Bar Finish: ❏ Chrome ❏ Brushed Nickel

❏ Faucet*:

❏ Supplies:

❏ P-Trap Finish: ❏ Chrome ❏ Brushed Nickel

* See Townsend faucet section for models available

J23

© 2017 AS America Inc.

spec_0328-Townsend Ped Sink Rev. A 7/17

FINISHED

WALL

TOWNSEND ®

PEDESTAL SINK and OPTIONAL FURNITURE

FINE FIRECLAY

2X HOLES FOR

ANCHOR BOLTS

8-3/8"

(213mm)

30"

(762mm)

FAUCET MOUNTING HOLES:

SINGLE HOLE, 4"(102mm) OR 8"(203mm)

2"

(50mm)

* 8"

(203mm)

8-1/2"

(215mm)

19-1/2"

(495mm)

* 22-3/4"

(578mm)

*20-1/2"

(521mm)

8"

(202mm)

7/8"

(22mm)

SUPPLIES

AS REQ'D

35-1/4"

(895mm)

1-1/4"

O.D. WASTE

1-1/4" O.D.

TAIL PIECE

PEDESTAL

BASE

FINISHED

FLOOR

DRAIN

CHASE

OPEN

TO

FLOOR

30"

(762 mm)

19-1/2"

(495 mm)

35-1/4"

(895 mm)

Vanity shown

(same dimensions as washstand)

NOTES:

* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAPS ARE SUGGESTED.

■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST BE TAKEN FROM FIXTURE.

FITTING NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.

INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.

FURNITURE SPECIFIC INSTRUCTIONS SUPPLIED WITH OPTIONAL FURNITURE.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerance established by ANSI Standard A112.19.2

These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

J24

© 2017 AS America Inc.

spec_0328-Townsend Ped Sink Rev. A 7/17

TOWNSEND ® ABOVE COUNTER SINK and OPTIONAL FURNITURE

❏ 0329.004 Faucet holes on 4" (102mm) centers

❏ 0329.008 Faucet holes on 8" (203mm) centers

❏ 0329.001 Faucet holes - center hole only (illustrated)

• Fine fireclay

• Rectangular above counter sink

• Front overflow

• Sink has glazed back wall

• Design coordinates with Townsend Collection

• Supplied with cut-out template

• Sink can be used with design matched quartz top with vanity or washstand furniture

TOWNSEND ® ABOVE COUNTER

SINK and OPTIONAL FURNITURE

BARRIER FREE

FINE FIRECLAY

Townsend above counter sink 0329.001

Bowl size:

16" (405 mm) wide

11" (280 mm) front-to-back

5" (128 mm) deep

Nominal Dimensions:

Above Counter Sink Only:

24" x 17-1/2" (610 x 454 mm)

Above Counter Sink and Furniture Combinations:

30" x 20" x 36-3/8" (762 x 508 x 923mm)

❏ 9036.030 30" (762mm) vanity less drawer pulls

❏ 7760.000 Drawer pulls (set of 2) for 30" (762mm) vanity

❏ 9039.030 30" (762mm) washstand less towel bar

❏ 3749.000 Towel bar for 30" (762mm) washstand

❏ 7840.000.820

Quartz top for above counter sink

❏ 7720.018 Optional decorative p-trap drain

Compliance Certifications -

Meets or Exceeds the Following Specifications:

• ASME A112.19.2/CSA B 45.1

To Be Specified:

❏ Chinaware Color: ❏ White ❏ Linen

❏ Vanity Finish: ❏ White ❏ Smoked Grey

❏ Vanity Drawer Pulls Finish: ❏ Chrome ❏ Brushed Nickel

❏ Washstand Finish: ❏ White ❏ Smoked Grey

❏ Washstand Towel Bar Finish: ❏ Chrome ❏ Brushed Nickel

❏ Faucet*:

❏ Supplies:

❏ P-Trap Finish: ❏ Chrome ❏ Brushed Nickel

* See Townsend faucet section for models available

Townsend above counter sink 0329.008

shown with 7840.000.820 quartz top and

9039.030 washstand and 3749.000 towel bar plus 7720.018 p-trap drain

SEE REVERSE FOR ROUGHING-IN DIMENSIONS

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES

AND ICC ANSI A117.1 ACCESSIBLE AND USABLE

BUILDINGS AND FACILITIES - CHECK LOCAL CODES.

Install lavatory 864mm (34") from finished floor.

Lavatory installed 102mm (4") minimum from front edge of countertop provides 686mm (27") knee clearance area.

Not compliant when used with optional furniture.

J29

© 2017 AS America Inc.

spec_0329TownsendAboveCtrRtgSink Rev. B 7/17

TOWNSEND ® ABOVE COUNTER

SINK and OPTIONAL FURNITURE

BARRIER FREE

FINE FIRECLAY

FAUCET MOUNTING HOLES:

SINGLE HOLE, 4"(102mm)

OR 8"(203mm)

2-15/16"

(75mm)

FINISHED WALL

9-1/16"

(230mm)

17-1/2"

(454mm)

*12-7/8"

327mm

*10-3/4"

273mm

FINISHED FLOOR

36-3/8"

(923 mm)

4"

(102mm)

25" MAX

(635mm)

COUNTER TOP

8" MIN

(205mm)

24"

(609mm)

2-3/16"

(55mm)

* 8"

203mm

SUPPLIES

AS REQ'D

7-1/8"

(181mm)

31"

(787mm)

SUGGESTED

34" MAX

(864mm)

27" MIN

(686mm)

BARRIER

FREE

CLEARANCE

1-1/4" O.D. WASTE

1-1/4" O.D. TAILPIECE

11" MIN

(280mm)

30"

(762 mm)

6" MAX

(152mm)

9" MIN

(229mm)

SUGGESTED ADA INSTALLATION

20"

(508 mm)

Washstand shown

(same dimensions as vanity)

NOTES:

* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE SUGGESTED.

FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS USE TEMPLATE SUPPLIED WITH SINK.

FURNITURE SPECIFIC INSTRUCTIONS SUPPLIED WITH OPTIONAL FURNITURE.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2.

These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

J30

© 2017 AS America Inc.

spec_0329TownsendAboveCtrRtgSink Rev. B 7/17

TOWNSEND

®

UNDER COUNTER SINK and OPTIONAL FURNITURE

BARRIER FREE

VITREOUS CHINA

TOWNSEND ® UNDER COUNTER SINK and OPTIONAL FURNITURE

❏ 0330.000 Unglazed Rim

• Rectangular under mount sink with tapered

interior bowl

• Made from vitreous china

• Unglazed rim

• Front overflow

• Supplied with mounting kit and template

• Coordinates with Townsend ® Collection

• Sink can be used with design matched quartz top with vanity or washstand furniture

Bowl Size:

17-3/4" (450mm) wide

11-5/8" (294mm) front to back

4-1/2" (115mm) deep

Nominal Dimensions:

Under Counter Sink Only

19-1/2" x 13-5/8" (495 x 346mm)

Above Counter Sink and Furniture Combinations:

30" x 20" x 34 (762 x 508 x 863mm)

❏ 9036.030

30" (762mm) vanity less drawer pulls

❏ 7760.000

Drawer pulls (set of 2) for 30" (762mm) vanity

❏ 9039.030 30" (762mm) washstand less towel bar

❏ 3749.000

Towel bar for 30" (762mm) washstand

❏ 7840.800.820

Quartz top with 8" (203mm) center faucet holes

❏ 7720.018

Optional decorative p-trap drain

Compliance Certifications -

Meets or Exceeds the Following Specifications:

• ASME A112.19.2/CSA B45.1

Townsend under counter sink 0330.000

Townsend under counter sink 0330.000

shown with 7840.800.820 quartz top and

9036.030 vanity and 7760.000 drawer pulls

SEE REVERSE FOR ROUGHING-IN DIMENSIONS

To Be Specified:

❏ Chinaware Color: ❏ White ❏ Linen

❏ Vanity Finish: ❏ White ❏ Smoked Grey

❏ Vanity Drawer Pulls Finish: ❏ Chrome ❏ Brushed Nickel

❏ Washstand Finish: ❏ White ❏ Smoked Grey

❏ Washstand Towel Bar Finish: ❏ Chrome ❏ Brushed Nickel

❏ Faucet*:

❏ Supplies:

❏ P-Trap Finish: ❏ Chrome ❏ Brushed Nickel

* See Townsend faucet section for models available

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES

AND ICC ANSI A117.1 ACCESSIBLE AND USABLE

BUILDINGS AND FACILITIES - CHECK LOCAL CODES.

Install lavatory 864mm (34") from finished floor.

Lavatory installed 102mm (4") minimum from front edge of countertop provides 686mm (27") knee clearance area.

Not compliant when used with optional furniture.

J71

© 2017 AS America Inc.

spec_0330_000TownsendUnderctrSink Rev. A 7/17

TOWNSEND

®

UNDER COUNTER SINK and OPTIONAL FURNITURE

BARRIER FREE

VITREOUS CHINA

2"

(51mm)

2"

(51mm)

11-5/8"

(294mm)

17-3/4"

(450mm)

A

4-3/8"

(110mm)

FINISHED WALL

OR BACKSPLASH

FITTING

CENTERSET

SPREAD

24"

(610mm)

A

4" (102 mm)

8" (203 mm)

4"

(102mm)

13-5/8"

(346mm)

1/2"

(12mm)

19-1/2"

(495mm)

* 8"

(203mm)

COUNTERTOP

(BY OTHERS)

4-1/2"

(115mm)

6-1/2"

(166mm)

34" MAX

(864mm)

27" MIN

(686mm)

8" MIN

(205mm)

BARRIER

FREE

CLEARANCE

SUPPLIES

AS REQ'D

1-1/4" O.D. WASTE

11" MIN

(280mm)

* 23-1/2"

(597mm)

* 21"

(533mm) FINISHED FLOOR

6" MAX

(152mm)

9" MIN

(229mm)

SUGGESTED ADA INSTALLATION

30"

(762 mm)

20"

(508 mm)

34"

(863 mm)

Vanity shown

(same dimensions as washstand)

NOTES:

* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAPS ARE SUGGESTED.

FITTING NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

FOR COUNTERTOP CUTOUT AND INSTALLATION USE TEMPLATE SUPPLIED WITH SINK.

FURNITURE SPECIFIC INSTRUCTIONS SUPPLIED WITH OPTIONAL FURNITURE.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerance established by ANSI Standard A112.19.2

These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

J72

© 2017 AS America Inc.

spec_0330_000TownsendUnderctrSink Rev. A 7/17

TOWNSEND ®

FREESTANDING TUB

HIGH GLOSS ACRYLIC

TOWNSEND ® FREESTANDING TUB

❑ 2691.004 TOWNSEND FREESTANDING TUB

Product Features:

• Contemporary styling

• High quality seamless acrylic construction with fiberglass reinforcement

• Center toe-tap drain

• Wide deck ledge on one side is ideal for deck mount

and/or handshower

• Wide deck ledge can be used to store bath accessories

• Integrated tub drain for easy installation

• Adjustable leveling feet under the tub

• Easy to clean high-gloss surface

• Coordinates with Townsend bathroom suite making

a complete bathroom remodel easier

• Limited Lifetime warranty

Nominal Dimensions:

68" x 36" x 24"

(1727 x 915 x 610mm)

Compliance Certifications -

Meets or Exceeds the Following Specifications:

• IAPMO Z124-2011

• CSA B45.5-11

• cUPC

SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

AND PRODUCT SPECIFICATIONS

To Be Specified - Required:

❏ Color: White

1582.000 Townsend ® Drain and Overflow Kit

Choose Finish:

.002 Chrome

.295 Brushed Nickel

.287 Polished Nickel

.013 Legacy Bronze

Recommended: For concrete slab installation

Drain adapter rough-in suggest

❏ OS&B ® ABS Island Tub Drain ™ Rough-In #ITD35

❏ PVC Island Tub Drain™ Rough-In #ITD5135

or

❏ Cast Iron Island Tub Drain Rough-In #ID357

Island Tub Drain ™ is a registered trademark of OS&B ®

H1b-23

© 2017 AS America Inc.

spec_2691.004 Townsend Freestanding Tub 8/17

TOWNSEND ®

FREESTANDING TUB

HIGH GLOSS ACRYLIC

67-15/16"

(1726 mm)

ø2-1/8"

(ø55 mm)

DRAIN OVERFLOW

17-1/2"

(444 mm)

2-1/4"

(57 mm)

3-1/8"

(80 mm)

60-3/16"

(1529 mm)

20"

36"

(914 mm)

(508 mm)

24"

(610 mm)

GENERAL SPECIFICATIONS FOR

2691 FREE STANDING BATH

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

68 x 36 x 24 in.

(1727 x 914 x 610mm)

100 Lbs. (45 Kg.)

645 Lbs. (293Kg.)

65 Gal. (246L)

41-1/2 x 21-1/2 In. (1054 x 546mm)

61-7/8 x 29-3/8 In. (1572 x 746mm)

15 In. (381mm)

38 Lbs./Sq.Ft. (186 Kgs./Sq.m)

NOTES:

■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH BATHTUB FOR ADDITIONAL INFORMATION.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1.2.

These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

H1b-24

© 2017 AS America Inc.

spec_2691.004 Townsend Freestanding Tub 8/17