Grizzly Industrial G0774 Automatic Edgebander Owner's Manual

Grizzly Industrial G0774 is an automatic edgebander that is perfect for edgebanding panels of various thicknesses and materials. With its high-precision construction, this edgebander ensures accurate and consistent edgebanding results. The G0774 is loaded with features that make it easy to use, including a user-friendly control panel, automatic glue application, and a built-in end trimmer.

PDF Download

Document

MODEL G0774

AUTOMATIC EDGEBANDER

OWNER'S MANUAL

(For models manufactured since 10/18)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#WKESJH18284 PRINTED IN TAIWAN V2.10.18

This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.

This responsibility includes but is not limited to proper installation in a safe environment, personnel training and usage authorization, proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals:

Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

INTRODUCTION ............................................... 2

Contact Info.................................................... 2

Manual Accuracy ........................................... 2

Identification (Front) ....................................... 3

Identification (Rear)........................................ 4

Controls & Components ................................. 5

Machine Data Sheet .................................... 12

SECTION 1: SAFETY ..................................... 15

Safety Instructions for Machinery ................ 15

Additional Safety for Automatic

Edgebanders ................................................ 17

SECTION 2: POWER SUPPLY ...................... 18

SECTION 3: SETUP ....................................... 20

Needed for Setup ......................................... 20

Unpacking .................................................... 20

Inventory ...................................................... 21

Hardware Recognition Chart ....................... 22

Site Considerations ...................................... 23

Lifting & Placing ........................................... 24

Assembly ..................................................... 25

Cleanup ........................................................ 29

Dust Collection ............................................. 30

Test Run ...................................................... 31

SECTION 4: OPERATIONS ........................... 34

Operation Overview ..................................... 34

Checking/Adding Glue ................................. 35

Setting Panel Feeder Height........................ 35

Setting Infeed Fence Position ...................... 36

Checking/Adjusting Glue Spindle Position... 37

Adjusting Flush Trimmer .............................. 38

Installing Edgebanding Coil ......................... 38

Performing Edgebanding Operation ............ 40

SECTION 5: ACCESSORIES ......................... 42

SECTION 6: MAINTENANCE ......................... 44

Schedule ...................................................... 44

Cleaning & Protecting .................................. 44

Lubrication ................................................... 45

SECTION 7: SERVICE ................................... 47

Troubleshooting ........................................... 47

Checking/Calibrating Infeed Fence Stop .... 51

Removing/Changing Glue ............................ 52

Replacing End Trimmer Blades ................... 53

Replacing Flush Trimmer Cutterhead Knives 54

Replacing Buffing Wheels ............................ 55

Adjusting Limit Switches .............................. 55

Checking/Adjusting Conveyor Belt Tension 56

Checking/Adjusting Pressure Roller Unit ..... 57

Checking/Adjusting End Trimmer Tracers ... 59

Checking/Adjusting End Trimmer

Drive Belt Tension ....................................... 61

Replacing End Trimmer Drive Belt .............. 63

Replacing Flush Trimmer Drive Belt ............ 63

SECTION 8: WIRING ...................................... 65

Wiring Safety Instructions ............................ 65

Electrical Panel Wiring Diagram .................. 66

Electrical Panel Photos ................................ 67

Terminal Block Wiring Diagram ................... 68

Motor Wiring Diagram .................................. 69

Motor Photos................................................ 70

Control Panel Wiring Diagram ..................... 71

Pneumatic Valve & Limit Switch Wiring

Diagram ....................................................... 73

Electrical Schematics ................................... 74

SECTION 9: PNEUMATIC SYSTEM .............. 80

SECTION 10: PARTS ..................................... 81

Parts Reference Page ................................. 81

Main Table ................................................... 82

Cover Panels ............................................... 84

Panel Feeder Elevation ............................... 85

Panel Feeder ............................................... 86

Panel Feeder Lock ....................................... 87

Pneumatic Guillotine .................................... 88

Flush Trimmer Motor ................................... 89

Coil Support ................................................. 90

Edgebanding Intake Assembly .................... 91

Pressure Roller ............................................ 92

Heated Fence .............................................. 93

Edgebanding Feeder ................................... 94

End Trimmer Carriage ................................. 95

End Trimmer Motor ...................................... 96

Vertical Edgebanding Guide & Glue Spindle 97

Glue Pot Cover ............................................ 98

Glue Pot ....................................................... 99

Glue Spindle Motor .................................... 100

Upper & Lower Buffing Motors .................. 101

Upper Flush Trimmer ................................. 102

Lower Flush Trimmer ................................. 103

Electrical Panel .......................................... 104

Labels & Cosmetics (Front) ....................... 105

Labels & Cosmetics (Rear) ........................ 106

WARRANTY & RETURNS ........................... 109

INTRODUCTION

Contact Info

We stand behind our machines! If you have questions or need help, contact us with the information below. Before contacting, make sure you get the

serial number and manufacture date from the machine ID label. This will help us help you faster.

Grizzly Technical Support

1815 W. Battlefield

Springfield, MO 65807

Phone: (570) 546-9663

Email: [email protected]

We want your feedback on this manual. What did you like about it? Where could it be improved?

Please take a few minutes to give us feedback.

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: [email protected]

Manual Accuracy

We are proud to provide a high-quality owner’s manual with your new machine!

We made every effort to be exact with the instructions, specifications, drawings, and photographs in this manual. Sometimes we make mistakes, but our policy of continuous improvement also means that sometimes the machine you receive is

slightly different than shown in the manual.

If you find this to be the case, and the difference between the manual and machine leaves you confused or unsure about something, check our website for an updated version. We post current manuals and manual updates for free on our website at www.grizzly.com.

Alternatively, you can call our Technical Support for help. Before calling, make sure you write down the Manufacture Date and Serial Number from the machine ID label (see below). This information is required for us to provide proper tech support, and it helps us determine if updated documentation is available for your machine.

Manufacture Date

Serial Number

-2Model G0774 (Mfd. Since 10/18)

Identification (Front)

Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual.

Panel

Feeder

Panel Feeder

Elevation

Handwheel

Buffing

Unit

End Trimmer

Dust Collection

Hose

Pressure

Rollers

Glue

Spindle

Heated

Fence

Digital

Control

Panel

Coil Support

Assembly

Flush

Trimmer

Unit

End

Trimmer

Unit

Figure 1. Component identification—front.

Adjustable

Table

Air Pressure

Regulator

Power

Connection Box

To reduce your risk of serious injury, read this entire manual BEFORE using machine.

Model G0774 (Mfd. Since 10/18) -3-

Identification (Rear)

Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual.

Rear Access

Cover

Glue Flow

Adjustment Knob

Edge Seat Height

Adjustment Knob

Flush Trimmer

Adjustment Knobs

End Trimmer

Motor

Upper

Dust Port

Upper and

-4-

Nylon Roller

Release Knob

Glue Spindle

Adjustment Knob

Electrical Panel

Access Doors Pneumatic

Control Panel

(Factory Set)

Flush

Trimmer

Motor

Figure 2. Component identification —rear.

To reduce your risk of serious injury, read this entire manual BEFORE using machine.

Lower

Dust Port

Model G0774 (Mfd. Since 10/18)

Controls &

Components

To reduce your risk of serious injury, read this entire manual BEFORE using machine.

Refer to the following figures and descriptions to become familiar with the basic controls and components of this machine. Understanding these items and how they work will help you understand the rest of the manual and minimize your risk of injury when operating this machine.

Control Panel

C D

N M L

K J I H G

Figure 3. Control panel.

A. Thermoregulator Display: Displays actual and set temperatures of glue pot.

B. Guillotine Sensor ON/OFF Button:

Activates sensor for guillotine pneumatic control (see Page 6).

C. End Trimmer Sensor ON/OFF Button:

Activates sensor for end trimmer pneumatic control (see Page 7).

D. Infeed Fence Heat ON/OFF Button: Controls infeed fence heating element. Allow 12–14 minutes to reach operating temperature.

E. Power Lamp: Illuminates when machine is in stand-by mode.

Model G0774 (Mfd. Since 10/18)

F. Emergency Stop/Reset Button: Stops all machine functions except for glue pot. Twist clockwise to reset.

G. Buffing Unit ON/OFF Button: Controls buffing motors (see Page 9).

H. Flush Trimmer ON/OFF Button: Controls flush trimmer motor (see Page 8).

I. End Trimmer ON/OFF Button: Controls end trimmer motor (see Page 7).

J. Panel Feeder ON/OFF Button: Controls panel feeder conveyor belt (see Page 9).

K. Motor OFF Button: Turns OFF all motors and motor-driven functions (except for glue spindle motor).

L. Temperature UP Key: Incrementally raises temperature of glue pot when pressed.

M. Temperature DOWN Key: Incrementally lowers temperature of glue pot when pressed.

N. Thermoregulator Function Key: Only used for initial factory programming of thermoregulator. Not intended for end-user adjustment.

Qualified service personnel only!

O. Temperature SET Key: Saves temperature setting after user input from Temperature UP/

DOWN key(s).

Coil Support

P Q

Figure 4. Coil support components.

P. Coil Support Assembly: Supports edgebanding coil during operation.

Q. Adjustable Guide Rollers (4): Holds edgebanding coil in place during operation. Adjust as needed according to size of coil.

-5-

Front

Rear S T

Figure 5. Guillotine and glue system controls & components.

guillotine

Guillotine

Limit Switch: When trailing end of workpiece passes over and releases switch, switch activates pneumatic guillotine to sever edgeband.

U. Glue Spindle: Applies melted glue to workpiece edge.

V. Glue Spindle Adjustment Knob: Rotate counterclockwise to move spindle closer to workpiece; rotate clockwise to move glue spindle farther away.

S. Pneumatic Guillotine: Severs trailing end of glued edgeband.

glue system

W. Glue Pot Lid: Remove to inspect glue pot or to add glue. Leave closed during operations.

Glue System

T. Glue Flow Adjustment Knob: Rotate counterclockwise to increase glue flow; rotate clockwise to decrease glue flow.

X. Glue Pot: Stores and heats glue for bonding edgeband to workpiece.

-6Model G0774 (Mfd. Since 10/18)

Front AC

Z Y

Rear

AB pressure rollers

Figure 6. Pressure rollers and end trimming system controls & components.

Pressure Rollers End Trimmer

Y. Stationary Pressure Roller: Presses edgeband against workpiece after glue is applied.

Position is not adjustable. end trimmer

End Trimmer Dust Collection Hose:

Removes sawdust and debris caused by end trimming operation.

Z. Adjustable Pressure Roller: Presses edgeband against workpiece after glue is applied.

Position can be adjusted to increase or decrease pressure as necessary (refer to

Page 57 for more information).

AD. End Trimmer Blades (Right and Left):

Rotate at approximately 9000 RPM and follow workpiece to trim leading and trailing ends of glued edgeband.

AA. Adjustable Pressure Roller Jam Nut:

Loosen to rotate adjustable pressure roller bolt. Tighten to secure setting.

— Right end trimmer blade trims leading end of edgeband.

— Left end trimmer blade trims trailing end of edgeband.

AB. Adjustable Pressure Roller Bolt: Loosen to increase pressure of adjustable pressure roller against edgeband and workpiece. Tighten to decrease pressure.

AE. End Trimmer Tracer: Guides end trimmer blades.

Model G0774 (Mfd. Since 10/18) -7-

Front

Rear

Figure 7. Flush trimming system controls & components.

flush trimmer

Flush Trimmer

Adjustable Flush Trimmer Tracer:

Guides upper flush trimmer cutter. Height adjusts simultaneously with panel feeder elevation adjustment (see Page 9 for more information).

AI. Flush Trimmer Axial Indicators (Upper

and Lower): Displays numerical distance of flush trimmer cutters from workpiece edge in millimeters.

AG. Stationary Flush Trimmer Tracer: Guides lower flush trimmer cutter.

AJ. Flush Trimmer Axial Adjustment Knobs

(Upper and Lower): Rotates counterclockwise to move flush trimmer cutters closer to workpiece edge; rotates clockwise to move cutters farther away.

AH. Flush Trimmer Cutters (Upper and Lower):

Rotates at approximately 10,000 RPM and trims height of glued edgeband, making it flush with top and bottom of workpiece.

Note: For best results, always adjust upper and lower flush trimmer cutters equally.

-8Model G0774 (Mfd. Since 10/18)

Front, open

Front, closed

Figure 8. Buffing system and panel feeder controls & components.

buffing unit

Buffing Unit

AK. Adjustable Buffing Wheel: Rotates at approximately 3000 RPM and polishes upper surface of glued and trimmed edgeband.

Height adjusts simultaneously with panel feeder elevation adjustment (see This Page for more information).

AN. Panel Feeder Elevation Handwheel:

Raises and lowers panel feeder according to workpiece thickness. Rotate clockwise to raise panel feeder; rotate counterclockwise to lower it. Handwheel base features a readout that displays height in millimeters.

Note: Panel feeder elevation handwheel also raises and lowers upper portions of flush trimming and buffing units (see Page 8 and This

Page for more information).

AL. Stationary Buffing Wheel: Rotates at approximately 3000 RPM and polishes lower surface of glued and trimmed edgeband.

Height is not adjustable.

panel feeder

Panel Feeder

AM. Panel Feeder: Uses conveyor belt to advance workpiece from infeed end of table to outfeed end of table during edgebanding operation.

Height is adjustable according to workpiece thickness.

AO. Panel Feeder Lock: Locks panel feeder in position during edgebanding operations.

AP. Pneumatic Panel Stop: Automatically lowers during operation to prevent multiple workpieces from entering panel feeder at same time. Automatically raises when workpiece exits panel feeder, to allow next operation.

Model G0774 (Mfd. Since 10/18) -9-

Front

Rear

Figure 9. Edgebanding feeder controls & components.

Edgebanding Feeder

AQ. Edgebanding Height Knobs (2): Secures edgebanding vertically within edgebanding intake guides. Loosen to adjust according to edgebanding width; tighten to secure setting.

Note: Leave approximately 0.2mm vertical play when setting knobs.

AR. Edgebanding Intake Guides (2): Guides edgebanding as it feeds into machine.

AS. Rubber Drive Roller: Advances edgebanding until it is severed by guillotine.

AU. Nylon Roller Release Knob: Pull knob to the right to release nylon roller pressure when removing or loading edgeband.

Release knob to apply pressure after edgebanding is properly loaded.

AV. Edgebanding Seat Adjustment Knob:

Rotate clockwise to raise upper section of edgebanding seat; rotate counterclockwise to lower upper section. Adjust as necessary according to edgebanding width.

AT. Nylon Roller: Forces edgebanding against rubber drive roller, providing necessary friction to advance edgeband.

Note: Leave approximately 1 ⁄

" vertical play when adjusting upper section height.

AW. Edgebanding Seat: Vertically supports edgebanding just prior to making contact with glued edge of workpiece. Use Edgebanding

Seat Adjustment Knob ( AU) to adjust seat according to edgebanding width.

-10Model G0774 (Mfd. Since 10/18)

Infeed Fence

Front

Power & Air

Top

Figure 10. Infeed fence controls & components.

AX. Fence Adjustment Lock Lever: Tighten to secure fence position; loosen to allow fence adjustment.

Fence Adjustment Knurled Cylinder:

Rotate to adjust fence position according to edgebanding thickness. Rotate counterclockwise for greater edgebanding thickness; rotate clockwise for less edgebanding thickness.

AZ. Heated Infeed Fence: Guides workpiece during operation while also heating workpiece edge for better glue adhesion.

BA. Fence Stop: Allows you to quickly and easily set the infeed fence position without having to use the scale (refer to Page 36 for details).

BB. Fence Adjustment Scale: Indicates position of fence relative to edgebanding thickness in millimeter increments.

Figure 11. Power and air fence controls & components.

Master Power ON/OFF Switch: Turns incoming power ON and OFF.

BD. Main Pressure Regulator: Adjusts incoming air pressure. Pressure should be set to

100 PSI. Lift knob up and rotate clockwise to increase PSI/counterclockwise to decrease

PSI, then push knob down to secure setting.

BE. Wiring Box: Location to permanently connect (hardwire) machine to power supply.

Model G0774 (Mfd. Since 10/18) -11-

Machine Data Sheet

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0774

AUTOMATIC EDGEBANDER

Product Dimensions:

Weight ........................................................................................................................................................................... 754 lbs.

Width (side-to-side) x Depth (front-to-back) x Height .................................................................. 109-1/2 x 60-1/2 x 49-1/2 in.

Footprint (Length/Width) ............................................................................................................................... 57-3/4 x 22-3/4 in.

Shipping Dimensions:

Type ........................................................................................................................................................................ Wood Crate

Weight ............................................................................................................................................................................ 875 lbs.

Length/Width/Height ...........................................................................................................................................84 x 29 x 52 in.

Must Ship Upright .................................................................................................................................................................Yes

Electrical:

Power Requirement ........................................................................................................................ 220V, Single-Phase, 60 Hz

Full-Load Current Rating ...................................................................................................................................................... 19A

Minimum Circuit Size ........................................................................................................................................................... 30A

Connection Type ..................................................................................................................................................... Cord & Plug

Power Cord Included ............................................................................................................................................................Yes

Power Cord Gauge ....................................................................................................................................................... 12 AWG

Plug Included ........................................................................................................................................................................Yes

Plug Type ...........................................................................................................................................................................L6-30

Switch Type ..........................................................................................................Control Panel w/Magnetic Switch Protection

Motors:

Feed

Type ................................................................................................................................ TEFC Capacitor-Start Induction

Horsepower ............................................................................................................................................................3/4 HP

Voltage ..................................................................................................................................................................... 220V

Phase .......................................................................................................................................................... Single-Phase

Amps ......................................................................................................................................................................... 3.6A

Speed ...............................................................................................................................................................1700 RPM

Power Transfer ................................................................................................................................................ Gear Drive

Bearings .........................................................................................................................Shielded & Permanently Sealed

Glue Spindle

Type ................................................................................................................................ TEFC Capacitor-Start Induction

Horsepower ............................................................................................................................................................1/3 HP

Voltage ..................................................................................................................................................................... 220V

Phase .......................................................................................................................................................... Single-Phase

Amps ......................................................................................................................................................................... 1.7A

Speed ...............................................................................................................................................................1720 RPM

Power Transfer ................................................................................................................................................ Gear Drive

Bearings .........................................................................................................................Shielded & Permanently Sealed

End Trim

Type ................................................................................................................................ TEFC Capacitor-Start Induction

Horsepower ............................................................................................................................................................1/4 HP

Voltage ..................................................................................................................................................................... 220V

Phase .......................................................................................................................................................... Single-Phase

Amps ......................................................................................................................................................................... 1.6A

Speed ...............................................................................................................................................................3400 RPM

Power Transfer ................................................................................................................................................Timing Belt

Bearings .........................................................................................................................Shielded & Permanently Sealed

Flush Trim

Type ................................................................................................................................ TEFC Capacitor-Start Induction

Horsepower ............................................................................................................................................................3/4 HP

Voltage ..................................................................................................................................................................... 220V

Phase .......................................................................................................................................................... Single-Phase

Amps ......................................................................................................................................................................... 3.5A

Speed ...............................................................................................................................................................3400 RPM

Power Transfer .................................................................................................................................................... Flat Belt

Bearings .........................................................................................................................Shielded & Permanently Sealed

Buffing

Type ................................................................................................................................ TEFC Capacitor-Start Induction

Horsepower ............................................................................................................................................................1/4 HP

Voltage ..................................................................................................................................................................... 220V

Phase .......................................................................................................................................................... Single-Phase

Amps ......................................................................................................................................................................... 1.6A

Speed ...............................................................................................................................................................3400 RPM

Power Transfer ...............................................................................................................................................Direct Drive

Bearings .........................................................................................................................Shielded & Permanently Sealed

Main Specifications:

Operation Information

Min. Panel Width ..................................................................................................................................................4-3/4 in.

Min. Panel Length ................................................................................................................................................9-1/2 in.

Panel Thickness (Min. – Max.) ................................................................................................................... 1/2 – 1-3/4 in.

Tape Thickness (Min. – Max.) ........................................................................................................................ 0.5 – 3 mm

Air Requirement ................................................................................................................................6 SCFM @ 100 PSI

Panel Feed Speed ................................................................................................................................................ 16 FPM

Glue Pot Capacity ...................................................................................................................................................34 oz.

Roller Width ..........................................................................................................................................................3-3/4 in.

Roller Diameter ...................................................................................................................................................13/16 in.

Max. Height of Rollers ................................................................................................................................. 0.8 – 1.0 mm

Edgebanding Coil Capacity ................................................................................................................................31-1/2 in.

Dust Collection Ports (2) ............................................................................................................................................4 in.

Dust Collection Requirement (at Dust Port) .......................................................................................................700 CFM

Heating Element ................................................................................................................................................1535W (t)

Table Information

Work Table Length .............................................................................................................................................78-3/4 in.

Work Table Width ...............................................................................................................................................10-1/2 in.

Construction

Housing .............................................................................................................................................................Aluminum

Frame ........................................................................................................................................................................Steel

Rollers ...................................................................................................................................................................Rubber

Paint .........................................................................................................................................................Powder Coated

Other Specifications:

Country of Origin ............................................................................................................................................................. Taiwan

Warranty ........................................................................................................................................................................... 1 Year

Approximate Assembly & Setup Time ........................................................................................................................... 2 Hours

Serial Number Location ...........................................................................................................Machine ID Label on Right Side

Sound Rating .................................................................................................................................................................... 80 dB

ISO 9001 Factory ..................................................................................................................................................................Yes

CSA Certified ......................................................................................................................................................................... No

Features:

Automatic belt feed with adjustable table rollers

Edgebanding from 0.5mm – 3mm

Panel thickness from 1/2" – 1-3/4"

16 FPM feed speed

Heated infeed fence for better glue dispersion

Pneumatic edgebanding guillotine

Double-bladed end-trimming saw

Upper and lower trimming units with digital readout

Upper and lower buffing units

Adjustable infeed fence for different edgebanding thicknesses

Extendable side bar to accommodate larger panels

Digital control panel controls each element individually

Teflon-coated glue pot with 5 heating elements and motorized glue spreader

31-1/2" tape coil support

Two 4-inch dust ports

Built-in air regulator and filter for pneumatic system

SECTION 1: SAFETY

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.

This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Always use common sense and good judgment.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

NOTICE

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury. It may also be used to alert against unsafe practices.

Alerts the user to useful information about proper operation of the machine to avoid machine damage.

Safety Instructions for Machinery

OWNER’S MANUAL. Read and understand this owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY. Untrained operators have a higher risk of being hurt or killed.

Only allow trained/supervised people to use this machine. When machine is not being used, disconnect power, remove switch keys, or lock-out machine to prevent unauthorized use—especially around children. Make your workshop kid proof!

ELECTRICAL EQUIPMENT INJURY RISKS.

You can be shocked, burned, or killed by touching live electrical components or improperly grounded machinery. To reduce this risk, only allow qualified service personnel to do electrical installation or repair work, and always disconnect power before accessing or exposing electrical equipment.

DANGEROUS ENVIRONMENTS. Do not use machinery in areas that are wet, cluttered, or have poor lighting. Operating machinery in these areas greatly increases the risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental alertness is required for safe operation of machinery. Never operate under the influence of drugs or alcohol, when tired, or when distracted.

DISCONNECT POWER FIRST. Always disconnect machine from power supply BEFORE making adjustments, changing tooling, or servicing machine. This prevents an injury risk from unintended startup or contact with live electrical components.

EYE PROTECTION. Always wear ANSI-approved safety glasses or a face shield when operating or observing machinery to reduce the risk of eye injury or blindness from flying particles. Everyday eyeglasses are NOT approved safety glasses.

Model G0774 (Mfd. Since 10/18) -15-

WEARING PROPER APPAREL. Do not wear clothing, apparel or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to reduce risk of slipping and losing control or accidentally contacting cutting tool or moving parts.

HAZARDOUS DUST. Dust created by machinery operations may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material. Always wear a NIOSH-approved respirator to reduce your risk.

HEARING PROTECTION. Always wear hearing protection when operating or observing loud machinery. Extended exposure to this noise without hearing protection can cause permanent hearing loss.

REMOVE ADJUSTING TOOLS. Tools left on machinery can become dangerous projectiles upon startup. Never leave chuck keys, wrenches, or any other tools on machine. Always verify removal before starting!

USE CORRECT TOOL FOR THE JOB. Only use this tool for its intended purpose—do not force it or an attachment to do a job for which it was not designed. Never make unapproved modifications—modifying tool or using it differently than intended may result in malfunction or mechanical failure that can lead to personal injury or death!

AWKWARD POSITIONS. Keep proper footing and balance at all times when operating machine.

Do not overreach! Avoid awkward hand positions that make workpiece control difficult or increase the risk of accidental injury.

FORCING MACHINERY. Do not force machine.

It will do the job safer and better at the rate for which it was designed.

NEVER STAND ON MACHINE. Serious injury may occur if machine is tipped or if the cutting tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement during operation greatly increases risk of injury or loss of control. Before starting, verify machine is stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult this owner’s manual or the manufacturer for recommended accessories. Using improper accessories will increase the risk of serious injury.

UNATTENDED OPERATION. To reduce the risk of accidental injury, turn machine OFF and ensure all moving parts completely stop before walking away. Never leave machine running while unattended.

MAINTAIN WITH CARE. Follow all maintenance instructions and lubrication schedules to keep machine in good working condition. A machine that is improperly maintained could malfunction, leading to serious personal injury or death.

DAMAGED PARTS. Regularly inspect machine for damaged, loose, or mis-adjusted parts—or any condition that could affect safe operation.

Immediately repair/replace BEFORE operating machine. For your own safety, DO NOT operate machine with damaged parts!

CHILDREN & BYSTANDERS. Keep children and bystanders at a safe distance from the work area.

Stop using machine if they become a distraction.

MAINTAIN POWER CORDS. When disconnecting cord-connected machines from power, grab and pull the plug—NOT the cord. Pulling the cord may damage the wires inside. Do not handle cord/plug with wet hands. Avoid cord damage by keeping it away from heated surfaces, high traffic areas, harsh chemicals, and wet/damp locations.

GUARDS & COVERS. Guards and covers reduce accidental contact with moving parts or flying debris. Make sure they are properly installed, undamaged, and working correctly BEFORE operating machine.

EXPERIENCING DIFFICULTIES. If at any time you experience difficulties performing the intended operation, stop using the machine! Contact our

Technical Support at (570) 546-9663.

-16Model G0774 (Mfd. Since 10/18)

Additional Safety for Automatic Edgebanders

Serious injury can occur from getting fingers pinched or crushed between workpiece and conveyor belt, or getting hair/clothing entangled in conveyor belt. Touching hot parts can cause serious burns. Long-term respiratory damage can occur from using edgebander without a respirator and adequate dust collection system. To minimize risk of injury, anyone operating this machine MUST completely heed hazards and warnings below.

HAND PLACEMENT. The gap between the conveyor belt and support table increases risk of pinching or crushing injuries. Minimize this risk by keeping fingers clear of infeed area when feeding workpieces.

AVOIDING ENTANGLEMENT. Becoming entangled in conveyor belt can cause crushing injuries.

To avoid these hazards, DO NOT wear loose clothing, gloves, or jewelry, and tie back long hair.

DUST COLLECTION. Never operate without adequate dust collection system in place and running. Proper dust collection reduces dust in work area, which decreases risk of long-term respiratory damage. However, a dust collector is not a substitute for using a respirator. Always wear a properly fitting respirator in addition to operating the dust collector.

GLUE POT & GLUE APPLICATOR. The glue pot and glue applicator get very hot and can cause serious burns. Always wear gloves when adding glue to glue pot. When servicing glue pot and applicator, make sure machine is turned OFF, disconnected from power, and components have properly cooled before handling.

POWER DISCONNECT. To reduce risk of electrocution or injury from unexpected startup, make sure machine is turned OFF, disconnected from power and air, and all moving parts have come to a complete stop before changing cutting tools, or starting any inspection, adjustment, or maintenance procedure.

BLADE REPLACEMENT. When replacing blades, cutters, or guillotine, disconnect machine from power, wear gloves to protect hands, and wear safety glasses to protect eyes.

SAFETY DEVICES. Do not modify or disable any limit switches, guards, or other safety devices on this machine. Doing so will void the warranty and expose operator to serious injury from mechanical, electrical, and pneumatic components inside machine.

HEATED FENCE. Heated fence is very hot and can cause serious burns. Avoid touching fence, especially when feeding small workpieces.

WEAR PROPER PPE. Always wear safety glasses, respirator, and hearing protection when operating edgebander.

ADEQUATE VENTILATION. When melted, edgebanding glue pellets can produce vapors and fumes that may irritate the nose, throat, and respiratory tract. Only operate this machine with proper ventilation near work area.

Model G0774 (Mfd. Since 10/18) -17-

SECTION 2: POWER SUPPLY

Availability

Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by an electrician or qualified service personnel in accordance with all applicable codes and standards.

Circuit Information

A power supply circuit includes all electrical equipment between the breaker box or fuse panel in the building and the machine. The power supply circuit used for this machine must be sized to safely handle the full-load current drawn from the machine for an extended period of time. (If this machine is connected to a circuit protected by fuses, use a time delay fuse marked D.)

Electrocution, fire, shock, or equipment damage may occur if machine is not properly grounded and connected to power supply.

Full-Load Current Rating

The full-load current rating is the amperage a machine draws at 100% of the rated output power.

On machines with multiple motors, this is the amperage drawn by the largest motor or sum of all motors and electrical devices that might operate at one time during normal operations.

Full-Load Current Rating at 220V ..... 19 Amps

The full-load current is not the maximum amount of amps that the machine will draw. If the machine is overloaded, it will draw additional amps beyond the full-load rating.

If the machine is overloaded for a sufficient length of time, damage, overheating, or fire may result— especially if connected to an undersized circuit.

To reduce the risk of these hazards, avoid overloading the machine during operation and make sure it is connected to a power supply circuit that meets the specified circuit requirements.

For your own safety and protection of property, consult an electrician if you are unsure about wiring practices or electrical codes in your area.

Note: Circuit requirements in this manual apply to a dedicated circuit—where only one machine will be running on the circuit at a time. If machine will be connected to a shared circuit where multiple machines may be running at the same time, consult an electrician or qualified service personnel to ensure circuit is properly sized for safe operation.

Circuit Requirements

This machine is prewired to operate on a power supply circuit that has a verified ground and meets the following requirements:

Nominal Voltage ................... 220V, 230V, 240V

Cycle ..........................................................60 Hz

Phase ........................................... Single-Phase

Power Supply Circuit ......................... 30 Amps

Plug/Receptacle ...........................NEMA L6-30

-18Model G0774 (Mfd. Since 10/18)

Grounding Requirements

This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current.

This machine is equipped with a power cord that has an equipment-grounding wire and a grounding plug. Only insert plug into a matching receptacle

(outlet) that is properly installed and grounded in accordance with all local codes and ordinances.

DO NOT modify the provided plug!

L6-30 GROUNDED

LOCKING

RECEPTACLE

Grounding Prong is Hooked

L6-30

LOCKING

PLUG

Current Carrying Prongs

Figure 12. Typical L6-30 plug and receptacle.

Serious injury could occur if you connect machine to power before completing setup process. DO NOT connect to power until instructed later in this manual.

Improper connection of the equipment-grounding wire can result in a risk of electric shock. The wire with green insulation (with or without yellow stripes) is the equipment-grounding wire. If repair or replacement of the power cord or plug is necessary, do not connect the equipment-grounding wire to a live (current carrying) terminal.

Check with a qualified electrician or service personnel if you do not understand these grounding requirements, or if you are in doubt about whether the tool is properly grounded. If you ever notice that a cord or plug is damaged or worn, disconnect it from power, and immediately replace it with a new one.

Extension Cords

We do not recommend using an extension cord with this machine. If you must use an extension cord, only use it if absolutely necessary and only on a temporary basis.

Extension cords cause voltage drop, which can damage electrical components and shorten motor life. Voltage drop increases as the extension cord size gets longer and the gauge size gets smaller

(higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine must be in good condition and contain a ground wire and matching plug/receptacle. Additionally, it must meet the following size requirements:

Minimum Gauge Size ...........................12 AWG

Maximum Length (Shorter is Better).......50 ft.

No adapter should be used with plug. If plug does not fit available receptacle, or if machine must be reconnected for use on a different type of circuit, reconnection must be performed by an electrician or qualified service personnel, and it must comply with all local codes and ordinances.

Model G0774 (Mfd. Since 10/18) -19-

-20-

SECTION 3: SETUP

This machine presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the machine!

Wear safety glasses during the entire setup process!

HEAVY LIFT!

Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a forklift (or other lifting equipment) rated for weight of this machine.

Needed for Setup

The following items are needed, but not included, for the setup/assembly of this machine.

Description Qty

• Another Person .......................................... 1

• Safety Glasses (for each person) ............... 1

• Lifting Equipment

(Rated for at least 1000 lbs.) ...................... 1

• Hex Wrench 4, 6, 8mm ........................1 Ea.

• Wrench or Socket 8mm .............................. 1

• Open-End Wrench 17mm ........................... 1

• Open-End Wrench 24mm ........................... 1

• Solvent/Cleaner .......................................... 1

• Shop Rags .................................................. 1

• Straightedge ............................................... 1

• Wire Snips .................................................. 1

Unpacking

This machine was carefully packaged for safe transport. When unpacking, separate all enclosed items from packaging materials and inspect them for shipping damage. If items are damaged, please call us immediately at (570) 546-9663.

IMPORTANT: Save all packaging materials until you are completely satisfied with the machine and have resolved any issues between Grizzly or the shipping agent. You MUST have the original pack- aging to file a freight claim. It is also extremely helpful if you need to return your machine later.

SUFFOCATION HAZARD!

Keep children and pets away from plastic bags or packing materials shipped with this machine.

Model G0774 (Mfd. Since 10/18)

Inventory

The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them.

If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store.

NOTICE

If you cannot find an item on this list, carefully check around/inside the machine and packaging materials. Often, these items get lost in packaging materials while unpacking or they are pre-installed at the factory.

Loose Item Inventory (Figure 13) Qty

A. Coil Support Mounting Arm ........................ 1

B. Panel Feeder Elevation Handwheel ........... 1

C. Glue Pot Lid ................................................ 1

D. Grease Gun (Not Shown) ........................... 1

Shipping Box Contents (Figure 14) Qty

E. Coil Support Assembly ............................... 1

F. Hardware Bag ............................................ 1

Hardware Bag Contents (Figure 15) Qty

G. Adjustable Guide Roller Assemblies .......... 4

—Threaded Roller Shafts

M8-1.25 x 12 x 52L ................................. 4

—Bushings ................................................. 4

—Flat Washers 8mm ................................. 4

—Roller Slide Nuts M8-1.25 ....................... 4

H. Coil Support Stud Assembly ...................... 1

—Stud-FT M10-1.5 x 150 ........................... 1

—Lock Nut M10-1.5 .................................... 1

—Hex Nuts M10-1.5 ................................... 2

—Fender Washers 10mm .......................... 3

B C

Figure 13. Loose item inventory.

Figure 14. Shipping box contents.

Figure 15. Hardware bag contents.

Model G0774 (Mfd. Since 10/18) -21-

-22-

5mm

Hardware Recognition Chart

USE THIS CHART TO MATCH UP

HARDWARE DURING THE INVENTORY

AND ASSEMBLY PROCESS.

Flat

Head

Cap

Screw

5

Model G0774 (Mfd. Since 10/18)

Site Considerations

Weight Load

Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest workpiece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.

Space Allocation

Consider the largest size of workpiece that will be processed through this machine and provide enough space around the machine for adequate operator material handling or the installation of auxiliary equipment. With permanent installations, leave enough space around the machine to open or remove doors/covers as required by the maintenance and service described in this manual.

See below for required space allocation.

Children or untrained people may be seriously injured by this machine. Only install in an access restricted location.

Physical Environment

The physical environment where the machine is operated is important for safe operation and longevity of machine components. For best results, operate this machine in a dry environment that is free from excessive moisture, hazardous chemicals, airborne abrasives, or extreme conditions.

Extreme conditions for this type of machinery are generally those where the ambient temperature range exceeds 41°–104°F; the relative humidity range exceeds 20%–95% (non-condensing); or the environment is subject to vibration, shocks, or bumps.

Electrical Installation

Place this machine near an existing power source.

Make sure all power cords are protected from traffic, material handling, moisture, chemicals, or other hazards. Make sure to leave enough space around machine to disconnect power supply or apply a lockout/tagout device, if required.

Lighting

Lighting around the machine must be adequate enough that operations can be performed safely.

Shadows, glare, or strobe effects that may distract or impede the operator must be eliminated.

Wall

= Electrical Connection

120"

Min. 30" for Maintenance

Keep

Workpiece

Unloading

Area

Unobstructed

Feed Direction

Model G0774 (Mfd. Since 10/18)

Figure 16. Minimum working clearances.

84" Keep

Workpiece

Area

Unobstructed

-23-

Lifting & Placing

It is always best to place machine on as flat a surface as possible to prevent tipping and rocking during operation. If the machine tips or rocks, and there is no other suitable location to place it, you will need to stablilize it, using the leveling bolts.

HEAVY LIFT!

To lift and place machine:

1. Position crate with machine as close to installation location as possible.

2. Remove top of crate, then remove plastic wrap and small items packed around machine.

3. Position forklift forks as wide as possible while still fitting under center opening of edgebander cabinet (see Figure 17). Protect machine body from forks with cardboard.

4. Unbolt machine from pallet.

5. Lift machine with forklift enough to clear pallet, then have an assistant slide pallet out of the way.

6. Position machine as necessary, then gently lower it onto floor.

7. Stabilize machine by loosening jam nuts and rotating leveling bolts (see Figure 18) until machine is level, then tighten jam nuts to secure. The leveling bolts are located at rear left and right corners of machine.

Leveling Bolt

Figure 18. Location of (1 of 2) leveling bolts with jam nuts.

Jam Nut

Figure 17. Inserting forks for lifting edgebander.

-24Model G0774 (Mfd. Since 10/18)

Assembly

The machine must be fully assembled before it can be operated. Before beginning the assembly process, refer to Needed for Setup and gather all listed items. To ensure the assembly process goes smoothly, first clean any parts that are covered or coated in heavy-duty rust preventative (if applicable).

Assembling the Model G0774 requires repositioning the control panel, installing the coil support assembly, installing the panel feeder elevation handwheel, and aligning the table extension with the table.

To assemble machine:

1. Remove (2) pre-installed M8-1.25 x 16 cap screws, (2) 8mm lock washers, and (2) 8mm flat washers that secure control panel in shipping position (see Figure 19).

2. Mount control panel upright with fasteners removed during Step 1 (see

Figure 20).

x 2

Figure 20. Control panel mounted in proper upright position (viewed from rear of machine).

3. Remove pre-installed M5-.8 x 45 cap screw and M5-.8 lock nut from panel feeder elevation handwheel (see Figure 21).

Control Panel x 2 x 1

Figure 19. Location of cap screws and washers securing control panel upside-down for shipping.

Figure 21. Location of pre-installed panel feeder elevation handwheel mounting hardware.

Model G0774 (Mfd. Since 10/18) -25-

4. Install handwheel on panel feeder elevation shaft (see Figure 22), and secure with fasteners removed in previous step.

x 1

6. Remove (2) pre-installed M10-1.5 hex nuts and (2) 10mm fender washers from coil support stud (see Figure 24).

Note: Leave (1) M10-1.5 hex nut and

(1) 10mm fender washer installed.

Remove These

Lock Nuts, Hex Nuts, &

Fender Washers

Do Not Remove

This Hex Nut &

Fender Washer

Figure 22. Panel feeder elevation handwheel installed.

5. Remove (2) pre-installed M8-1.25 x 20 cap screws, (2) 8mm lock washers, and (2) 8mm flat washers, then use them to install coil support arm (see Figure 23).

Figure 24. Coil support stud.

7. Thread stud up through bottom of coil support arm (see Figure 25).

Stud

Coil Support

Arm x 2

Coil

Support Arm

Hex Nut Fender

Washer

Figure 25. Stud threaded into coil support arm.

Figure 23. Coil support arm installed.

-26Model G0774 (Mfd. Since 10/18)

8. Install (1) M10-1.5 hex nut and (1) 10mm fender washer on coil support stud (see

Figure 26), and tighten hex nut against top of coil support arm, then tighten hex nut against bottom of support arm (see Figure 26).

Stud

Coil

Support

Arm

Fender

Washer

Hex Nut

Fender

Washer

Hex Nut

Figure 26. Stud secured against coil support arm.

9. Install coil support assembly on stud and secure with remaining M10-1.5 lock nut and

10mm fender washer (see Figure 27).

Lock Nut

Coil Support

Assembly

Fender

Washer

10. Remove slide nut from each of four guide roller assemblies (see Figure 28).

Slide Nut Guide

Roller Assembly

(1 of 4)

Figure 28. Guide roller assembly and slide nut

(1 of 4).

11. Place slide nut under slot in coil support assembly, then thread guide roller with washers into nut from above and tighten, as shown in Figure 29. Repeat with remaining three guide roller assemblies in each of the remaining slots.

Guide Roller

Washer

Slot

Figure 27. Coil support assembly installed.

Slide Nut

Figure 29. Guide roller installed in coil support slot.

Model G0774 (Mfd. Since 10/18) -27-

12. Loosen panel feeder lock lever (see

Figure 30).

Panel Feeder

Lock Lever

14. Remove shipping tag from rear access cover, then open cover and remove shipping tag from end-trimming motor (see Figures 32–33).

Shipping

Tag

Figure 30. Location of panel feeder lock lever.

13. Rotate panel feeder elevation handwheel clockwise to slightly raise panel feeder, then remove wood shipping blocks from infeed and outfeed ends of table (see Figure 31).

Wood

Shipping

Block

Wood

Shipping

Block

Rear Access

Cover

Figure 32. Location of rear access cover shipping tag to be removed.

Shipping

Tag

Outfeed End Infeed End

Figure 31. Location of wood shipping blocks to be removed.

End

Trimming

Motor

Figure 33. Location of end-trimming motor shipping tag to be removed.

15. Pull out extension table (see Figure 34) as far as it goes.

-28-

Figure 34. Extension table extended.

Model G0774 (Mfd. Since 10/18)

16. Place straightedge over infeed (right) end of main table and extension table. Make sure straightedge touches top of extension table roller above leg (see Figure 34).

— If straightedge makes solid contact across entire infeed end of main table and top of extension table roller, no adjustment is necessary. Proceed to Step 18.

— If straightedge does not make solid contact across entire infeed end of main table and top of extension table roller, extension table is not aligned with main table and must be adjusted. Proceed to Step 17.

Infeed

End

Roller

Figure 35. Checking extension table to see if it is aligned with main table.

17. Loosen jam nut at bottom of extension table leg, rotate adjustable foot nut until extension table is aligned with main table, then tighten jam nut against bottom of leg to secure setting (see Figure 36).

Extension

Table Leg

Jam Nut

Adjustable

Foot Nut

Adjustable

Foot

Figure 36. Location of extension table alignment components.

18. Repeat Steps 16–17 for outfeed (left) end of table.

Model G0774 (Mfd. Since 10/18)

Cleanup

The heated infeed fence is coated with a heavyduty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean.

Be patient and do a thorough job cleaning. The infeed fence gets extremely hot during operations, and could create harmful fumes if any residue is left on the fence.

There are many ways to remove this rust preventative, but the following steps work well in a wide variety of situations. Always follow the manufacturer’s instructions with any cleaning product you use and make sure you work in a well-ventilated area to minimize exposure to toxic fumes.

Before cleaning, gather the following:

• Disposable rags

• Cleaner/degreaser (WD•40 works well)

• Safety glasses & disposable gloves

• Plastic paint scraper (optional)

Basic steps for removing rust preventative:

1. Put on safety glasses.

2. Coat rust preventative with a liberal amount of cleaner/degreaser, then let it soak for 5–10 minutes.

3. Wipe off surfaces. If your cleaner/degreaser is effective, rust preventative will wipe off easily. If you have a plastic paint scraper, scrape off as much as you can first, then wipe off the rest with rag.

4. Repeat Steps 2–3 as necessary until all rust preventative and cleaner/degreaser are completely removed.

-29-

Dust Collection

Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. Avoid using these products to clean machiner y.

Many cleaning solvents are toxic if inhaled. Only work in a well-ventilated area.

NOTICE

Avoid chlorine-based solvents, such as acetone or brake parts cleaner, that may damage painted surfaces.

T23692—Orange Power Degreaser

A great product for removing the waxy shipping grease from your machine during clean up.

This machine creates a lot of wood chips/ dust during operation. Breathing airborne dust on a regular basis can result in permanent respiratory illness. Reduce your risk by wearing a respirator and capturing the dust with a dust-collection system.

Recommended CFM at Dust Port: 800 CFM

Do not confuse this CFM recommendation with the rating of the dust collector. To determine the

CFM at the dust port, you must consider these variables: (1) CFM rating of the dust collector,

(2) hose type and length between the dust collector and the machine, (3) number of branches or wyes, and (4) amount of other open lines throughout the system. Explaining how to calculate these variables is beyond the scope of this manual. Consult an expert or purchase a good dust collection "how-to" book.

To connect dust collection hoses:

1. Fit a 4" dust hose over each dust port, as shown in Figure 38, and secure in place with hose clamps.

2. Tug hoses to make sure they do not come off. Note: A tight fit is necessary for proper performance.

Figure 37. T23692 Orange Power Degreaser.

-30-

Figure 38. Dust hoses attached to dust ports.

Model G0774 (Mfd. Since 10/18)

Test Run

Once assembly is complete, test run the machine to ensure it is properly connected to power and safety components are functioning correctly.

If you find an unusual problem during the test run, immediately stop the machine, disconnect it from power, and fix the problem BEFORE operating the machine again. The Troubleshooting table in the

SERVICE section of this manual can help.

Serious injury or death can result from using this machine BEFORE understanding its controls and related safety information.

DO NOT operate, or allow others to operate, machine until the information is understood.

2. Ensure panel feeder is closed and locked, and rear access door is closed. If either of these items is not properly closed, machine will not function.

3. Clear all setup tools and loose items away from machine.

4. Turn master power switch OFF and press

Emergency Stop button in.

5. Connect machine to power by inserting power cord plug into a matching receptacle, then connect machine to an air supply and adjust air regulator to 100 PSI.

6. Twist Emergency Stop button clockwise until it springs out (see Figure 39). This resets switch so machine can start.

DO NOT start machine until all preceding setup instructions have been performed.

Operating an improperly set up machine may result in malfunction or unexpected results that can lead to serious injury, death, or machine/property damage.

The test run consists of verifying the following:

• Glue pot powers up and reaches working temperature of 356° F (180° C)

• Heated infeed fence powers-up

• Guillotine and edge trimmer sensors power-up

• Each motor powers-up and runs correctly

• Emergency Stop button works correctly

• Safety limit switches work correctly

To test run machine:

1. Read and follow safety instructions at beginning of manual, take all required safety precautions, and make sure all previous setup/ assembly steps in this manual have been followed and completed.

Figure 39. Resetting the switch.

7. Turn master power switch ON.

Thermoregulator display on control panel should illuminate (see Figure 40).

Thermoregulator

Display

Upper

Number

Figure 40. Thermoregulator display illuminated after master power switch turned ON.

Model G0774 (Mfd. Since 10/18) -31-

8. Watch thermoregulator display and listen for glue spindle motor to start. When upper number (see Figure 40 on Page 31) reaches

180° C, glue spindle motor should turn ON.

Note: Spindle motor won't turn ON if

Emergency Stop Button is in.

9. Press guillotine sensor ON/OFF button (see

Figure 41); button should illuminate, indicating sensor is activated. Press button again; button should darken, indicating sensor is no longer activated.

Guillotine

Sensor

ON/OFF

Button

End Trimmer

Sensor

ON/OFF

Button

Infeed

Fence

ON/OFF

Button

12. Press panel feeder ON/OFF button (see

Figure 42). Button should illuminate. Panel feeder motor should start up and run smoothly without any unusual problems or noises.

Flush Trimmer

ON/OFF

Button

Buffing Unit

ON/OFF

Button

Figure 41. Guillotine sensor, end trimmer sensor, and infeed fence ON/OFF buttons.

10. Perform same activation test (Step 9) for end trimmer sensor (see Figure 41).

11. Press infeed fence ON/OFF button (see

Figure 41); button should illuminate, indicating fence is heating up. Press button again; button should darken, indicating fence is no longer heating and has begun to cool down.

Panel Feeder

ON/OFF Button

End Trimmer

ON/OFF Button

Figure 42. Panel feeder, end trimmer, flush trimmer, and buffing unit ON/OFF buttons.

13. Perform same motor test (Step 12) for endtrimmer, flush trimmer, and buffing unit motors

(see Figure 42).

14. Turn all upper and lower green ON/OFF buttons ON (see Figure 43).

Upper Green

ON/OFF Buttons

Lower Green

ON/OFF Buttons

Fence gets extremely hot—up to 410°F

(210°C). To avoid serious burns, DO NOT touch fence while it is turned ON or while still hot after being turned OFF.

OFF

Button

Emergency Stop/

Reset Button

Figure 43. Upper and lower green ON/OFF buttons, OFF button, and Emergency Stop/Reset button.

-32Model G0774 (Mfd. Since 10/18)

15. Press OFF button (see Figure 43 on

Page 32). All upper green ON/OFF buttons should remain illuminated. All lower green

ON/OFF buttons should darken, and the following motors should turn OFF.

• panel feeder

• end trimmer

• flush trimmer

• buffing unit

16. Press all lower green ON/OFF buttons again.

They should illuminate and their respective motors should turn ON.

17. Press Emergency Stop button (see

Figure 43 on Page 32). All upper and lower green ON/OFF buttons should darken, and their respective components and motors should turn OFF.

Note: The only machine functions that should still be in operation are glue pot heating element and thermoregulator display.

18. WITHOUT resetting Emergency Stop button, press each green ON/OFF button one at a time.

— If no green ON/OFF buttons illuminate and no sensors activate or motors turn

ON, the Emergency Stop button safety feature is working correctly. Proceed to

Step 19.

— If any green ON/OFF buttons illuminate and any sensors activate or motors turn

ON, immediately turn master power switch OFF and disconnect machine from power. The Emergency Stop button safety feature is not working correctly.

This safety feature must work correctly before proceeding with regular operations.

Call Tech Support for help.

19. Twist Emergency Stop button to reset it.

20. Open rear access door, then press each green ON/OFF button one at a time.

— If no green ON/OFF buttons illuminate and

no sensors activate or motors turn ON, the rear access door safety limit switch is working correctly. Proceed to Step 21.

— If any green ON/OFF buttons illuminate and any sensors activate or motors turn

ON, immediately turn master power switch OFF and disconnect machine from power. The rear access door safety limit switch is not working correctly. This safety feature must work correctly before proceeding with regular operations. Call

Tech Support for help.

21. Open panel feeder, then press each green

ON/OFF button one at a time.

— If no green ON/OFF buttons illuminate and

no sensors activate and no motors turn

ON, the feeder panel safety limit switch is working correctly. Congratulations! The

Test Run is complete.

— If any green ON/OFF buttons illuminate and any sensors activate or motors turn

ON, immediately turn master power switch OFF and disconnect machine from power. The feeder panel safety limit switch is not working correctly. This safety feature must work correctly before proceeding with regular operations. Call

Tech Support for help.

Model G0774 (Mfd. Since 10/18) -33-

SECTION 4: OPERATIONS

Operation Overview

To complete a typical operation, the operator does the following:

The purpose of this overview is to provide the novice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easier to understand.

Due to the generic nature of this overview, it is

not intended to be an instructional guide. To learn more about specific operations, read this entire manual, seek additional training from experienced machine operators, and do additional research outside of this manual by reading "how-to" books, trade magazines, or websites.

To reduce your risk of serious injury, read this entire manual BEFORE using machine.

To reduce risk of eye injury from flying chips or lung damage from breathing dust, always wear safety glasses and a respirator when operating this machine.

If you are not experienced with this type of machine, WE STRONGLY RECOMMEND that you seek additional training outside of this manual. Read books/magazines or get formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training.

1. Checks to make sure there is enough glue in the glue pot.

2. Examines workpiece to make sure it is suitable for edgebanding.

3. Sets panel feeder height according to workpiece thickness.

4. Adjusts positions of infeed fence, glue spindle, and flush trimmers according to edgebanding thickness.

5. Installs correct size of edgebanding coil for workpiece thickness.

6. Puts on safety glasses and a respirator.

7. Connects machine to air and power, verifies air pressure is set to 100 PSI, and waits for glue pot to reach at least 180°C.

8. Activates guillotine and end-trimmer sensors and turns infeed fence ON. Waits for infeed fence to heat up.

9. Sets glue temperature according to glue manufacturer's instructions, then waits for glue pot to reach that temperature.

10. Turns ON panel feeder, end trimmer, flush trimmer, and buffing unit.

11. Places workpiece against heated infeed fence, and slides it under panel feeder, allowing panel feeder to take control of workpiece.

12. Receives edgebanded workpiece at outfeed end of machine.

13. When finished, stops machine, turns it OFF, and disconnects it from power.

-34Model G0774 (Mfd. Since 10/18)

Checking/Adding

Glue

Always check the glue level and, if necessary, add glue before operations. The glue pot is full when the glue reaches 3 ⁄

" (2cm) below the top of the pot.

Note: For instructions on removing and chang- ing glue, refer to Removing/Changing Glue on

Page 52 of the Service section.

Items Needed Qty

Glue Pellets ....................................... As Needed

To check/add glue:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Open rear access door and remove glue pot lid (see Figure 44). Determine if pot needs glue pellets (see Figure 44).

Glue Pot Lid Glue Pot is Full

When Glue

Reaches 3 /

(2cm) Below

Top of Glue Pot

Panel Feeder Elevation

Setting Panel Feeder

Height

The panel feeder must be set to match the workpiece thickness. The height adjusts with a handwheel and locks in place with a lock lever.

To set panel feeder height:

1. Measure workpiece thickness in millimeters.

2. Loosen panel feeder lock lever (see

Figure 45).

Panel Feeder

Lock Lever

Figure 45. Location of panel feeder lock lever.

3. Rotate panel feeder elevation handwheel until numerical display on base of handwheel matches measurement from Step 1 (see

Figure 46). Rotate handwheel clockwise to

raise panel feeder; rotate handwheel coun-

terclockwise to lower panel feeder.

Handwheel

Figure 44. Checking glue level in glue pot.

3. Carefully add glue pellets until glue reaches

3 ⁄

" (2cm) below top of glue pot, then close glue pot lid and close rear access door.

Tip: Add small amounts of glue pellets fre- quently for better melting consistency.

Model G0774 (Mfd. Since 10/18)

Numerical

Display

Figure 46. Panel feeder elevation handwheel with numerical display.

4. Retighten panel feeder lock lever (see

Figure 45) to secure panel feeder.

-35-

Setting Infeed Fence

Position

The infeed fence position is set according to the edgebanding thickness.

There are two methods for setting the infeed fence position: 1) using the infeed fence scale, and 2) using the infeed fence stop (see Figure 47).

Use whichever method best suits your needs and situation.

Infeed Fence

Lock Lever

Knurled

Cylinder

Scale

Fence Stop

Figure 47. Infeed fence adjustment components.

Using Infeed Fence Scale

The numbers on the infeed scale correspond to the edgebanding thickness (in millimeters). When using the infeed scale, simply adjust the fence until the scale indicates the correct edgebanding thickness.

To set infeed fence position using scale:

1. Carefully measure thickness of edgebanding to be used.

2. Loosen infeed fence adjustment lock lever, rotate knurled cylinder until number indicating thickness of edgebanding aligns with mark on scale (see Figure 47), then retighten lock lever.

Using Infeed Fence Stop

The infeed fence stop allows you to quickly and easily set the infeed fence position without having to use the scale. It is particularly useful when switching back and forth between different edgebanding thicknesses, or when the thickness of the edgebanding cannot be expressed in whole millimeters.

With this method, you place a scrap piece of the edgebanding you intend to use between the stop bolt and stop plate (see Figure 48), then adjust the fence until the stop plate presses firmly against the scrap piece.

Note: For best results, the infeed fence stop should be periodically checked for accuracy and, if necessary, calibrated (see Checking/Calibrating

Infeed Fence Stop on Page 51 for details).

To set infeed fence position using stop:

1. Cut a 1"–3" long section from edgebanding you intend to use.

2. Loosen infeed fence adjustment lock lever, then rotate knurled cylinder to create a gap between stop plate and stop bolt (see

Figure 48).

3. Place scrap piece from Step 1 between stop bolt and stop plate, as shown in Figure 48.

Section of Edgebanding

Stop

Bolt

Stop

Plate

Figure 48. Using infeed fence stop to set infeed fence position.

4. Rotate knurled cylinder until stop plate presses firmly against scrap piece, then tighten infeed fence lock lever to secure setting.

-36Model G0774 (Mfd. Since 10/18)

Checking/Adjusting Glue Spindle Position

Checking/Adjusting

Glue Spindle

Position

The glue spindle draws heated glue up from the glue pot and applies it to the workpiece edge just before the edgebanding is applied.

The position of the glue spindle must be checked and adjusted any time you change edgebanding or adjust the infeed fence position.

Items Needed Qty

Workpiece at Least 27" Long ............................ 1

To check/adjust glue spindle position:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Set infeed fence position to "0" (see Page 36).

3. Open panel feeder, then place straight, "factory edge" of workpiece against infeed fence and glue spindle, as shown in Figure 49.

— If workpiece edge makes solid contact with glue spindle and entire length of fence, glue spindle is properly positioned and no adjustment is necessary.

— If workpiece does not make solid contact with glue spindle and entire length of fence, glue spindle is not properly positioned. Proceed to Step 4.

Workpiece Contacting

Glue Spindle

4. Use glue spindle adjustment knob on rear of machine (see Figure 50) to adjust glue spindle position until workpiece makes solid contact with spindle and entire length of infeed fence.

— Rotate glue spindle adjustment knob

counterclockwise to move glue spindle

toward workpiece edge.

— Rotate glue spindle adjustment knob

clockwise to move spindle away from workpiece edge.

Glue Spindle

Adjustment

Knob

Figure 50. Location of glue spindle adjustment knob.

Workpiece Contacting

Infeed Fence

Figure 49. Checking glue spindle position.

Model G0774 (Mfd. Since 10/18) -37-

Flush Trimming Unit Adjustment

Adjusting Flush

Trimmer

The flush trimmer trims excess height off of the upper and lower edges of newly applied edgebanding, making it flush with the top and bottom of the workpiece.

The flush trimmer consists of two cutterheads

(one upper and one lower) that must each be separately adjusted toward or away from the workpiece, according to the edgebanding thickness. Always adjust upper and lower cutterheads equally.

To adjust flush trimmer:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Carefully measure thickness (in millimeters) of edgebanding you intend to use.

3. Rotate each flush trimmer adjustment knob until number displayed in readout equals thickness of edgebanding (see Figure 51).

Note: Rotate knobs counterclockwise to move flush trimmers closer to workpiece; rotate knobs clockwise to move them farther away.

Numerical

Readouts

Installing

Edgebanding Coil

The edgebanding coil (not included) is a coiled strip of wood or plastic veneer that is automatically fed into the edgebander and glued to the workpiece edge during the edgebanding process. The Model G0774 Automatic Edgebander uses edgebanding tape from 1 ⁄

"–1 3 ⁄

" wide.

For best results, the edgebanding tape width must be slightly greater than the workpiece thickness. The excess edgebanding tape is automatically trimmed flush with the workpiece during operations.

The edgebanding tape thickness affects machine setup. Before installing the edgebanding coil, the following components should be checked and, if necessary, adjusted, depending on the edgebanding tape thickness:

• Heated infeed fence position (see Page 36)

• Glue spindle position (see Page 37)

• Upper and lower flush trimmer positions

To install edgebanding coil:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Loosen edgebanding height knobs on intake guides (see Figure 52), raise knobs to allow room for edgebanding tape, then tighten to secure.

Intake

Guides

Adjustment

Knobs

Figure 51. Location of flush trimmer adjustment knobs (rear access cover opened for illustration purposes).

-38-

Edgebanding

Height Knobs

Figure 52. Location of edgebanding height knobs.

Model G0774 (Mfd. Since 10/18)

3. Loosen guide rollers on coil support (see

Figure 53) and move them out to allow room for edgebanding coil.

4. Center edgebanding coil on coil support.

Move guide rollers so they just touch coil, then tighten to secure (see Figure 53).

Note: Ensure coil can rotate freely. If coil cannot rotate freely, re-adjust guide rollers until it can.

5. Insert end of edgebanding tape into intake guides (see Figures 52–53).

Guide Rollers

(1 of 4)

Edgebanding

Coil

6. Rotate edgebanding seat adjustment knob (see Figure 54) clockwise to raise upper portion of seat and allow room for edgebanding tape.

7. Move nylon roller release knob to the right and manually advance edgebanding tape all the way forward, past nylon roller, to end of edgebanding seat (see Figure 54).

Note: Nylon roller release knob is spring- loaded. Hold it in released position (to the right) while you manually move edgebanding tape past roller.

Edgebanding Seat

Adjustment Knob

Edgebanding

Seat

Nylon Roller

Intake

Guides

Coil Support

Figure 53. Edgebanding coil installed on coil support.

Nylon Roller

Release Knob

Figure 54. Edgebanding tape advanced to forward end of edgebanding seat (viewed from rear of machine).

8. Rotate edgebanding seat adjustment knob counterclockwise to lower upper portion of seat until edgebanding tape has just enough room to move freely back and forth. Leave approximately 1 ⁄

" vertical play.

9. Loosen edgebanding height knobs from

Step 2 on Page 38, adjust knobs until edgebanding tape has just enough room to move freely back and forth, then tighten to secure.

Leave approximately 1 ⁄

" vertical play.

Model G0774 (Mfd. Since 10/18) -39-

10. Move nylon roller release knob to the right, then manually move edgebanding tape back, until its end is just in front of nylon roller

(see Figure 55). The edgebanding tape is now properly set up in starting position for operations.

Move End of Edgebanding

Tape to this Location

Nylon Roller

Figure 55. Starting position for edgebanding tape (viewed from rear of machine).

Performing

Edgebanding

Operation

Once all of the initial setup is complete, performing the edgebanding operation is a relatively simple and quick procedure.

Any workpiece you intend to edgeband with the

G0774 must have at least one straight and square edge that is at least 9 1 ⁄

" long.

It is always best to start with a test piece of the same material and dimensions as your intended workpiece, in order to verify all of your settings are correct.

Note: Spindle motor won't turn ON if emergency stop button is pressed.

For long workpieces that extend beyond the length of the table, it may be helpful to set up roller stands at either end of the table to add additional workpiece support during operations.

To perform edgebanding operations:

1. Read and follow all safety and initial setup instructions described earlier in this manual.

2. Inspect workpiece to make sure it is suitable for edgebanding.

3. Properly adjust panel feeder elevation (refer to Page 35), infeed fence position (refer to

Page 36), and flush trimmer (refer to Page

38).

4. Properly install edgebanding coil (refer to

Page 38).

5. Press Emergency Stop button, turn master power switch ON.

Important: In Steps 5–9, Emergency Stop button must be released before spindle motor will turn.

-40Model G0774 (Mfd. Since 10/18)

6. Rotate Emergency Stop button to reset it, then press lower green ON/OFF buttons to start machine (see Figure 56).

7. Use Temperature UP/DOWN keys to set glue pot temperature according to glue manufacturer's instructions. Wait for glue pot to reach at least 180°C, then glue spindle motor will start (see Figure 56).

Wait For This

Number to Reach

180°C

Upper and Lower

ON/OFF Buttons

11. Carefully slide workpiece under panel feeder, making sure to keep hands and fingers away from moving conveyor belt. When you feel panel feeder grab workpiece, allow panel feeder to advance workpiece through to outfeed end of table (see Figures 58–59).

Note: For long workpieces, it may be neces- sary to support trailing end of workpiece with your hands or a roller stand until it begins to move across table.

Then, as workpiece begins to exit outfeed end of table, support leading end of workpiece with hands or roller stand while panel feeder continues to feed workpiece through.

Outfeed

End

Glue Temp.

Up/Down Keys

Emergency Stop

Button

Figure 56. Location of edgebanding controls.

8. Press upper green ON/OFF buttons, shown in Figure 56, to activate pneumatic guillotine sensor, end trimmer sensor, and heated infeed fence.

9. Wait for glue pot (see glue manufacturer's instructions) and infeed fence to reach working temperatures. Machine is now ready to begin edgebanding.

10. Place straight edge of workpiece on infeed end of table and press it firmly against infeed fence, as shown in Figure 57.

Keep Hands and Fingers Away from This Area

Figure 58. Panel feeder advancing workpiece.

Conveyor Belt

Viewed From

Under Panel

Feeder

Workpiece

Figure 57. Placing workpiece on table in preparation for edgebanding.

Model G0774 (Mfd. Since 10/18)

Figure 59. Location of conveyor belt (panel feeder shown in open position for illustration purposes).

12. Receive edgebanded workpiece at outfeed end of table (see Figure 58). Allow panel feeder to completely finish feeding workpiece, then remove workpiece from table.

-41-

ACCESSORIES

SECTION 5: ACCESSORIES

Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage.

To reduce this risk, only install accessories recommended for this machine by Grizzly.

NOTICE

Refer to our website or latest catalog for additional recommended accessories.

Edgebanding, Non-Glued Veneer

T27174—0.5mm x 7 ⁄

" x 500' Maple

T27175—0.5mm x

T27176—0.5mm x 7

T27177—0.5mm x 7

T27178—0.5mm x

⁄

" x 500' Red Oak

⁄

" x 500' Black Melamine

⁄

" x 500' White Melamine

⁄

" x 500' White Pine

T27179—0.5mm x 7 ⁄

" x 500' Yellow Pine

T27180—1.5mm x 7

T27181—1.5mm x

T27182—2.0mm x

T27183—2.0mm x

T27184—3.0mm x 7 ⁄

" x 328' Maple

T27185—3.0mm x 7

T27186—3.0mm x 1

T27187—3.0mm x 1

⁄

" x 328' Maple

⁄

" x 328' Red Oak

⁄

" x 328' Maple

⁄

" x 328' Red Oak

⁄

" x 328' Maple

⁄

" x 328' Red Oak

H7978—Fractional Digital Caliper.

Large LCD readout converts to decimal inch, fractional inch and millimeters with the push of a button. Measure internal, external dimensions, depth, steps and differential measurements.

Features thumb roll and stainless steel construction. Range: 0-6", 0-150mm. Resolution: 0.0005",

0.01mm, 1 ⁄

128

Figure 61. H7978 Fractional Digital Caliper.

T27707—Edgebanding Glue Pellets, 44 lb.

We've combined the newest hot-melt technology with special additives to create low-density glue pellets with the highest possible bonding strength.

This provides greater efficiency, higher productivity, and practically invisible glue lines! Great for

PVC, ABS, veneer, solid wood, melamine, and polyester. These pellets come in a 44 lb. bag.

Figure 60. Grizzly non-glued, veneer edgebanding coils (T27174 shown).

Figure 62. T27707 Edgebanding Glue Pellets.

order online at

www.grizzly.com

or call

1-800-523-4777

-42Model G0774 (Mfd. Since 10/18)

G0825—Portable Edgebander w/Case & Kit

Easily apply edgebanding from 3 ⁄

" to 2 1 ⁄

" wide along straight runs, around bends, and inside corners! This machine combines the great features of a stationary edgebanding machine (hot melt glue application, speed feeding, and temperature control) with the convenience and portability of a handheld tool. Comes with a deluxe hard case with extension handle and roller wheels.

G1029Z2P—2HP Dust Collector

The great combination of price and performance make this one of the most popular dust collectors we sell. Perfect for use as a central dust collector in a small shop or as a "dedicated" dust collector next to an industrial machine. Features 220V single-phase power, 1550 CFM, 2.5 micron filtration, and a 6" main inlet w/included 4" x 2” "Y" fitting.

Figure 63. G0825 Portable Edgebander w/Case

& Kit.

Edgebanding Hand Tools

G7911—Trimmer, Double Edge

G7914—Hand Iron

G7915—J Roller

G7916—Bent Roller

These edgebanding hand tools are great for hard to reach areas, curved edges, workpieces that are too small for powered edgebanders, and when you're just in the mood to use some hand tools!

G7914

G7916

Figure 65. G1029Z2P 2HP Dust Collector.

Basic Eye Protection

T20501—Face Shield Crown Protector 4"

T20502—Face Shield Crown Protector 7"

T20503—Face Shield Window

T20451—“Kirova” Clear Safety Glasses

T20452—“Kirova” Anti-Reflective S. Glasses

T20456—DAKURA Safety Glasses, Black/Clear

T20502

T20503

T20452

G7915

G7911

T20456 T20451

Figure 66. Assortment of basic eye protection.

Figure 64. Grizzly edgebanding hand tools.

order online at

www.grizzly.com

or call

1-800-523-4777

Model G0774 (Mfd. Since 10/18) -43-

SECTION 6: MAINTENANCE

To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, maintenance, or service.

Schedule

For optimum performance from this machine, this maintenance schedule must be strictly followed.

Ongoing:

To maintain a low risk of injury and proper machine operation, if you ever observe any of the items below, shut down the machine immediately and fix the problem before continuing operations:

• Lubricate glue spindle (see Page 45).

• Clean/Lubricate end-trimming motor sliders

(see Page 45).

• Check for dull or damaged end-trimming saw blade(s) (see Page 53).

• Check for dull or damaged flush-trimmer knives (see Page 54).

• Worn or damaged wires.

• Any other unsafe condition.

Weekly Maintenance

• Clean off any glue residue on machine.

• Drain water in air filter collection cups.

• Lubricate flush-trimmer adjustment shafts

(see Page 46).

• Clean and lubricate guillotine assembly.

• Blow dust out of motor fans with compressed air.

Monthly Check

• Clean/vacuum dust buildup from all edgebanding components and motors.

• Lubricate edgebanding feed gears (see

Page 46).

• Lubricate flush-trimmer adjustment shafts

• Motor belt tension, damage, or wear.

• Conveyor belt tension, damage, or wear.

• Inspect entire machine for loose parts or signs of abnormal wear.

-44-

Cleaning &

Protecting

Cleaning the Model G0774 is relatively easy.

Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth, or blow off with compressed air. If any resin has built up, use a resin-dissolving cleaner to remove it.

Protect the unpainted cast-iron infeed fence by wiping it clean after every use and after it cools— this ensures moisture from wood dust does not remain on the bare metal surface. Keep the infeed fence rust-free with regular applications of products like G96 ® Gun Treatment, SLIPIT ® , or

Boeshield ® T-9.

Recommended Metal Protectants

G5562—SLIPIT

G5563—SLIPIT

® 1 Qt. Gel

® 12 Oz. Spray

G2871—Boeshield ®

G2870—Boeshield

H3788—G96

H3789—G96

® Gun Treatment 12 Oz. Spray

T-9 12 Oz. Spray

T-9 4 Oz. Spray

Gun Treatment 4.5 Oz. Spray

Figure 67. Recommended products for protecting unpainted cast iron infeed fence.

Model G0774 (Mfd. Since 10/18)

Lubricating Glue Spindle

Lubrication

NOTICE

The recommended lubrication is based on light-to-medium usage. Keeping in mind that lubrication helps to protect the value and operation of the machine, these lubrication tasks may need to be performed more frequently than recommended here, depending on usage.

Failure to follow reasonable lubrication practices as instructed in this manual could lead to premature failure of machine components and will void the warranty.

Glue Spindle

Lube Type ............ T26419 or NLGI#2 Equivalent

Lube Amount ..................................... As Needed

Lube Frequency ........................30 Hours of Use

The glue spindle is lubricated by a grease fitting on the back of the machine (see Figure 68).

Glue Spindle

Grease Fitting

End-Trimmer Motor Sliders

Lube Type ..............T26685 or ISO 32 Equivalent

Lube Amount ..................................... As Needed

Lube Frequency .......................................... Daily

The end trimmer motor sliders must be kept clean and lubricated to allow the smoothest possible movement of the end trimmer motor.

To lubricate the end trimmer motor sliders, open the rear access door to access the sliders (see

Figure 69). Wipe the sliders clean with a rag, then apply a light film of machine oil to the sliders.

Manually move motor back and forth and up and down to evenly distribute the oil along the sliders.

Figure 69. Location of end trimmer motor sliders.

Figure 68. Location of glue spindle grease fitting.

To lubricate the glue spindle, use the included grease gun to squirt a small amount of grease into fitting, then wipe away any excess grease with a rag.

Model G0774 (Mfd. Since 10/18) -45-

Flush Trimmer Adjustment Shafts

Lube Type ...Model T26685 or ISO 32 Equivalent

Lube Amount ..................................... As Needed

Lube Frequency ...................................... Weekly

The flush trimmer adjustment shafts (see

Figure 70) require a small amount of lubrication to allow smooth adjustment and prevent the shafts from seizing up.

Edgebanding Feed Gears

Lube Type ............ T26419 or NLGI#2 Equivalent

Lube Amount ..................................... As Needed

Lube Frequency ......................................Monthly

The edgebanding feed gears (see Figure 71) should be checked and, if necessary, lubricated periodically to ensure proper feeding of edgebanding during operations.

Lubricate Gears

Here

Figure 70. Lubrication points on the flush trimmer adjustment shafts.

To lubricate the flush trimmer adjustment shafts, use a cotton swab, small oil can, or other means to apply a light film of machine oil to the shafts, then adjust the upper and lower cutterheads in and out a few times to evenly distribute the oil.

Figure 71. Location of edgebanding feed gears.

To lubricate the gears, remove the rear access panel, apply a small amount of grease to the teeth, wipe away any excess grease with a rag, then re-install the rear access panel.

-46Model G0774 (Mfd. Since 10/18)

SECTION 7: SERVICE

Review the troubleshooting procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support. Note: Please gather the serial number and manufacture date of your machine before calling.

Troubleshooting

Motor & Electrical

Symptom

Machine does not turn on, one or more motors do not start, or a breaker trips.

Possible Cause

1. Emergency Stop button depressed/at fault.

2. Master power switch off/at fault.

3. Panel feeder/rear access panel left open.

4. Plug/receptacle at fault/wired wrong.

5. Power supply circuit breaker tripped/fuse blown.

6. Incorrect power supply voltage/circuit size.

7. Inadequate air pressure.

Possible Solution

1. Rotate button head to reset. Replace.

2. Turn switch ON; test/replace switch.

3. Close and secure panel feeder/rear access panel.

4. Test for good contacts; correct wiring.

5. Ensure circuit is sized correctly and free of shorts; reset circuit breaker/replace fuse.

6. Ensure correct power supply voltage/circuit size.

7. Ensure incoming air pressure is at least 6 SCFM @

100 PSI; adjust air pressure regulator to 100 PSI.

8. Allow glue pot to reach 180°C.

One or more motors stall or are underpowered.

8. Glue pot has not reached operating temperature.

9. Blown fuse on machine.

10. Thermal overload relay(s) tripped.

11. Motor wires connected incorrectly.

12. Wiring open/has high resistance.

13. Start capacitor(s) at fault.

14. Contactor(s) not energized/has poor contacts.

15. Centrifugal switch at fault.

16. Circuit board at fault.

17. Motor(s) at fault.

1. Motor(s) overheated.

2. Belt(s) slipping; oil/grease on belt(s).

3. Motor(s) wired incorrectly.

4. Plug/receptacle at fault.

5. Conveyor belt slipping/at fault.

6. Run capacitor at fault.

7. Pulley/sprocket slipping on shaft.

8. Centrifugal switch at fault.

9. Motor bearings at fault.

9. Check/replace blown fuses.

10. Reset; contact tech support if relay frequently trips.

11. Correct motor wiring connections.

12. Check/fix broken, disconnected, or corroded wires.

13. Test/replace.

14. Test all legs for power/replace.

15. Test/replace.

16. Inspect/replace.

17. Test/repair/replace.

1. Allow motor(s) to cool; reset overload if necessary.

2. Clean/tension/replace belt(s) ( Pages 61–64).

3. Wire motor(s) correctly.

4. Test for good contacts/correct wiring.

5. Tension belt ( Page 56); replace if faulty.

6. Test/repair/replace.

7. Replace loose pulley/shaft.

8. Adjust/replace centrifugal switch if available.

9. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement.

-47Model G0774 (Mfd. Since 10/18)

Motor & Electrical (Continued)

Symptom

Machine has vibration or noisy operation.

Possible Cause

1. Motor or component loose.

2. Belt(s) worn or loose.

3. Buffing wheel(s) at fault/incorrectly mounted.

4. Motor fan rubbing on fan cover.

5. Pulley loose.

6. Machine incorrectly mounted.

7. Motor bearings at fault.

8. Belt(s) slapping cover/components.

9. Flush trimmer knives at fault.

10. End-trimmer blades dull/incorrectly mounted.

11. Spindle/arbor bearings at fault.

12. Centrifugal switch is at fault.

13. Motor shaft bent.

Possible Solution

1. Inspect/replace damaged bolts/nuts, and retighten with thread locking fluid.

2. Inspect belts; tension/replace belts ( Pages 61–64).

3. Inspect/reinstall buffing wheel(s); replace.

4. Fix/replace fan cover; replace loose/damaged fan.

5. Re-align/replace shaft, pulley set screw, and key.

6. Tighten mounting bolts; relocate/shim machine.

7. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement.

8. Replace/realign belt(s) ( Pages 61–64).

9. Resharpen/replace knives; set knife alignment/ height correctly ( Page 54).

10. Inspect/resharpen/re-install/replace blades

( Page 53).

11. Test by rotating spindle/arbor; rotational grinding/ loose shaft requires bearing replacement.

12. Replace.

13. Test with dial indicator and replace motor.

Glue Spindle

Symptom

Glue spindle does not rotate.

Glue spindle does not dispense enough glue.

Possible Cause

1. Motor does not run.

2. Too much grease added to glue spindle.

3. Gear connection shaft stripped/broken.

4. Gear connection shaft stuck.

1. Glue flow out of adjustment.

2. Glue not fully melted, temperature setting too low.

3. Glue not fully melted, heater rods not working correctly.

4. Glue spindle not making full contact with workpiece.

5. Obstruction in glue shaft.

6. Burnt glue in glue spindle.

7. Glue pot thermometer not accurate.

Glue not fully melted in glue pot.

1. Glue pot still heating.

2. Glue pot temperature is set too low.

3. Heater rods at fault.

Possible Solution

1. Refer to Page 47.

2. Remove pressure-relief set screw.

3. Inspect/replace gear connection shaft.

4. Adjust motor reducer connection plate.

1. Adjust glue flow ( Page 52).

2. Adjust glue pot temperature according to glue manufacturer's directions; confirm glue temperature using laser thermometer.

3. Inspect heater rod connections; tighten if necessary.

Test heater rod amperage (top: 315W, 1.0A; lower large: 250W, 0.9A; lower small: 160W, 0.6A); replace if necessary.

4. Adjust glue spindle ( Page 37).

5. Remove obstruction from glue shaft.

6. Remove burnt glue from glue spindle.

7. Inspect thermocouple connections and wires for damage/wear; repair/replace if necessary.

1. Wait until glue reaches working temperature.

2. Adjust glue pot temperature according to glue manufacturer's directions; confirm glue temperature using laser thermometer.

3. Inspect heater rod connections; tighten if necessary.

Test heater rod amperage (top: 315W, 1.0A; lower large: 250W, 0.9A; lower small: 160W, 0.6A); replace if necessary.

-48Model G0774 (Mfd. Since 10/18)

Glue Spindle (Continued)

Symptom

Glue only adheres to lower portion of workpiece edge.

Possible Cause

1. Panel feeder not exerting enough downward force on workpiece.

2. Panel feeder lifts up when closed and latched.

3. Glue spindle not making full contact with workpiece.

4. Adjustable pressure roller not making full contact with workpiece.

5. Pressure roller tilted.

6. Glue spindle tilted.

7. Workpiece too wide, not properly supported.

Possible Solution

1. Lower panel feeder to 0.5mm below actual workpiece thickness ( Page 35).

2. Adjust panel feeder latch.

3. Adjust glue spindle ( Page 37).

4. Check/adjust pressure roller ( Page 57).

5. Adjust pressure roller so it is 90° to table.

6. Adjust glue spindle so it is 90° to table.

7. Pull out table extension/use additional support, such as roller stands.

End Trimmer

Symptom

Blades do not rotate.

End cut not straight/ not parallel.

Chips inside of panel.

Saw blades lose

RPM during operation.

End trimmer unit fails to slide on shafts.

Possible Cause

1. Motor does not run.

2. Belt damaged/broken.

3. Obstruction preventing blades from rotating.

1. Tracer pads out of adjustment.

2. Copy plate bent.

3. Inadequate air pressure.

1. Tracer pads out of adjustment.

2. Copy plate bent.

1. Belt is loose/damaged/broken.

2. Saw blades are dull/broken.

1. Zip-tie used to secure unit during shipping still attached.

2. Build-up on shafts prevent unit from sliding properly.

3. Inadequate air supply.

Possible Solution

1. Refer to Page 47.

2. Inspect/replace belt ( Pages 61–63).

3. Remove obstruction.

1. Properly adjust tracer pads ( Page 59).

2. Repair/replace copy plate.

3. Check/remedy air pressure.

1. Properly adjust tracer pads ( Page 59).

2. Repair/replace copy plate.

1. Inspect/replace belt ( Pages 61–63).

2. Inspect/sharpen/replace saw blades ( Page 53).

1. Remove zip-tie.

2. Clean shafts.

3. Check air lines for leaks/check air valves for blockages; repair.

Flush Trimmer

Symptom

Cutterheads do not rotate.

Possible Cause

1. Motor does not run.

2. Belt is loose/damaged/broken.

1. Cutterheads not properly adjusted.

Flush trimmer does not trim proper amount of edgebanding.

Cutterheads lose RPM during operation.

Cutterheads will not adjust in or out.

1. Belt is loose/damaged/broken.

2. Cutterhead knives are dull/broken.

1. Debris stuck between cylinder and housing.

2. Burrs preventing movement.

Possible Solution

1. Refer to Page 47.

2. Inspect/replace belt ( Page 63).

1. Properly adjust cutterheads ( Page 38).

1. Inspect/replace belt ( Page 63).

2. Inspect/replace knives ( Page 54).

1. Lubricate flush trimmer shafts to free up movement.

2. Remove cylinder, inspect/clean and lightly sand both surfaces, then re-install cylinder.

Model G0774 (Mfd. Since 10/18) -49-

Panel Feeder

Symptom

Conveyor belt does not move.

Workpiece feeds erradically or stops feeding during operation.

Possible Cause

1. Motor does not run.

2. Conveyor belt not properly tensioned.

1. Conveyor belt not properly tensioned.

2. Panel feeder height not properly adjusted.

Possible Solution

1. Refer to Page 47.

2. Properly tension conveyor belt ( Page 56).

1. Properly tension conveyor belt ( Page 56).

2. Properly adjust panel feeder height ( Page 35).

Buffing Unit

Symptom

Buffing wheel(s) do not rotate.

Buffing wheel(s) spread glue on workpiece.

Buffing wheel(s) wear away corners of workpiece/ edgebanding.

Possible Cause

1. Motor(s) do not run.

2. Buffing wheel(s) not properly secured.

1. Too much glue applied.

2. Wrong glue for application.

1. Buffing wheel(s) not properly adjusted.

Edgebanding Results

Symptom

Edgebanding moves up or down relative to workpiece.

Edgebanding cut too short (early) or too long (late).

Possible Cause

1. Pressure roller angle out of adjustment.

1. Inadequate workpiece support.

2. Guillotine valve switch out of adjustment.

3. Copy plate bent.

1. Flush trimmer cutterheads not properly adjusted.

Too much/ not enough edgebanding left on top or bottom.

Scrape marks on face of edgebanding.

Gaps in edgebanding on finished workpiece.

Ends not cleanly cut.

1. Debris/sharp edges/burrs/extra glue obstructing path of edgebanding.`

1. Guillotine limit switch set too low.

2. Panel feeder not exerting enough downward force on workpiece.

1. End trimmer saw blades dull.

Possible Solution

1. Refer to Page 47.

2. Tighten bolt(s) that secure wheel(s) ( Page 55).

1. Adjust glue flow ( Page 52).

2. Use appropriate glue for application, refer to glue manufacturer's instructions.

1. Properly adjust buffing wheel(s) ( Page 55).

Possible Solution

1. Adjust pressure roller so it is 90° to table.

1. Pull out table extension.

2. Properly adjust guillotine valve switch ( Page 55).

3. Repair/replace copy plate.

1. Properly adjust flush trimmer cutterheads

( Page 38).

1. Inspect entire path of edgebanding; clean away debris; sand/file sharp edges/burrs.

1. Raise position of guillotine limit switch.

2. Lower panel feeder to 0.5mm below actual workpiece thickness ( Page 35).

1. Sharpen/replace end trimmer saw blades

( Page 53).

-50Model G0774 (Mfd. Since 10/18)

Checking/Calibrating

Infeed Fence Stop

Fence Scale

Reads "0"

To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, maintenance, or service.

For best results, the infeed fence stop should be periodically checked for accuracy and, if necessary, calibrated.

Item(s) Needed Qty

Open-End Wrench 10mm .................................. 2

To check/calibrate infeed fence stop:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Loosen infeed fence lock lever, rotate knurled cylinder clockwise until stop plate contacts stop bolt, then retighten lock lever (see

Figure 72).

3. Check fence scale (see Figure 72).

— If fence scale reads "0," infeed fence stop is calibrated and no adjustment is necessary.

— If fence scale does not read "0," infeed fence stop is not calibrated. Proceed to

Step 4.

Stop Plate

Contacting

Stop Bolt

Figure 72. Checking infeed fence stop calibration.

4. Loosen jam nut (see Figure 73).

5. Loosen stop bolt a few turns (see Figure 73).

6. Loosen infeed fence lock lever, rotate knurled cylinder until fence scale reads "0."

— Rotate cylinder clockwise to move fence

toward stop bolt.

— Rotate cylinder counterclockwise to move fence away from stop bolt.

Stop Plate

Model G0774 (Mfd. Since 10/18)

Jam Nut

Stop Bolt

Figure 73. Calibrating infeed fence stop.

7. If necessary, repeat Steps 5–6 until you can adjust fence to "0."

8. Retighten lock lever.

9. Tighten stop bolt until it contacts stop plate, then tighten jam nut to secure stop bolt.

Infeed fence stop is now calibrated (see

Figure 73).

-51-

Removing/Changing

Glue

Removing/Changing Glue

If your edgebanding operation requires a different type of glue, or if the glue becomes contaminated with debris, you will need to remove the old glue and replace it with new glue pellets.

IMPORTANT: Glue pot is Teflon-coated. Do not scratch surface when servicing.

Item(s) Needed Qty

Wood Stick Approximately 6" x 1" x 1 ⁄

" ............ 1

Pliers .................................................................. 1

Glue Pellets ....................................... As Needed

To remove/change glue:

1. Turn machine OFF and wait for glue pot to

completely cool.

2. Turn machine ON and wait for glue pot to reach 80°–90° C.

3. Use wood stick (approximately 6" x 1" x to peel up one side of glue, as shown in

Figure 74.

1 ⁄

At 80°–90°C, Glue Peels

Away From Glue Pot

4. Use pliers to grip peeled up portion of glue and pull block of glue out of glue pot (see

Figure 75).

Important: Be careful not to scratch glue pot surface.

Figure 75. Using pliers to remove block of glue from glue pot.

5. Turn machine OFF, and allow glue pot to completely cool.

6. Clean any remaining glue and debris from bottom and sides of glue pot.

7. Carefully add glue pellets until they reach 3 ⁄

(2cm) below top of glue pot.

8. Turn machine ON and allow glue pot to reach operating temperature.

9. When glue pellets are completely melted, check glue level and, if necessary, add proper amount of glue (refer to Page 35 for more information).

Figure 74. Using wood stick to peel glue away from glue pot for glue removal.

-52Model G0774 (Mfd. Since 10/18)

Replacing End Trimming Saw Blades

Replacing End

Trimmer Blades

Saw blades are extremely sharp. Even dull blades can cause serious cuts when handled improperly. To reduce risk of injury, always wear leather gloves when working around blades.

If the end-trimmer fails to make clean, precise cuts, the blades ( Grizzly Part #P07741318) may be dull or damaged, requiring replacement.

Item(s) Needed Qty

Leather Gloves ...........................................1 Pair

Hex Wrenches 4, 6mm ................................1 Ea.

Wrench or Socket 10mm ................................... 1

Wood Block Approximately 1" x 3" .................... 1

To replace end trimmer saw blades:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Manually raise end trimmer unit and support it with wood block for best access to blades

(see Figure 76).

4. Use 6mm hex wrench to secure end trimmer spindle, and use 10mm wrench to remove hex bolt that secures end trimmer blades

(see Figure 77). Alternatively, secure end trimmer by inserting a hex wrench through hole in spindle (see Figure 78).

Note: Hex bolt has left-hand threads. Rotate

bolt clockwise to loosen; rotate bolt counterclockwise to tighten.

5. Remove blade flange, outer blade, spacer, and inner blade (see Figures 77–78).

Spindle

Hole

Securing Spindle

Outer Blade

Blade

Flange

Hex

Bolt

Removing Bolt

Figure 77. Removing end trimmer blades with dust shroud removed.

Inner Blade

Spacer

Wood Block

Supporting Raised

End Trimmer Unit

Figure 76. End trimmer unit raised and supported with wood block for access to blades.

3. Use 4mm hex wrench to remove end trimmer dust shroud assembly (see Figure 77).

Model G0774 (Mfd. Since 10/18)

Figure 78. Location of inner end trimmer blade and spacer.

6. Install new blades with spacer, flange, and hex bolt removed in Steps 4–5 in reverse order from removal.

Important: Make sure to orient components

(see Figure 78) in same direction as they were before removal.

-53-

Replacing Flush Trimmer Knives

Replacing Flush

Trimmer Cutterhead

Knives

If the flush trimmer fails to produce straight, clean upper and lower edges that are flush with the top and bottom surfaces of the workpiece, the flush trimmer cutterhead knives ( Grizzly

Part #P07742144-3 (upper) and #P07742235-

3 (lower)) may be dull or damaged requiring replacement.

The disposable upper and lower flush trimmer knives are held in place by blocks and set screws

(see Figures 79–80).

Item(s) Needed Qty

Hex Wrench 4mm .............................................. 1

To replace flush trimmer cutterhead knives:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Unlock and open panel feeder, then raise it all the way up.

3. Rotate upper or lower cutterhead until knife, lock, and set screw are accessible, as shown in Figures 79–80.

4. Loosen set screw (see Figure 81), remove knife, being careful not to drop or misplace block, install new knife, then retighten set screw.

Block

Knife

(1 of 4)

Set

Screw

Figure 79. Lower flush trimmer knife components.

Block

Knife

(1 of 4)

Set

Screw

Figure 80. Upper flush trimmer knife components.

Figure 81. Loosening gib screw to change flushtrimmer knife.

5. Repeat Steps 3–4 with remaining knives on cutterhead.

6. If necessary, repeat Steps 3–5 with knives of other cutterhead.

7. Close and lock panel feeder.

-54Model G0774 (Mfd. Since 10/18)

Replacing Buffing Wheels

Replacing Buffing

Wheels

If the buffing wheels become worn or damaged, or if they fail to produce smooth, polished upper and lower edges, the wheels ( Grizzly

Part #P07741903) will need to be replaced.

Item(s) Needed Qty

Wrench or Socket 13mm ................................... 1

Hex Wrench 5mm .............................................. 1

To replace buffing wheels:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Remove hex bolt securing upper buffing wheel (see Figure 82). Bolt has left-hand threads (clockwise to loosen; counterclock-

wise to tighten).

Note: If arbor spins, secure it by inserting a

5mm hex wrench into arbor cap screw.

3. Remove lock washer, flange, and buffing wheel (see Figure 82).

Buffing

Wheel

Flange

Lock

Washer

Hex Bolt

Figure 82. Buffing wheel removal components.

4. Install new buffing wheel and re-install flange, lock washer, and hex bolt, in reverse order from removal.

IMPORTANT: Orient components in same direction as they were before removal.

5. Repeat Steps 2–4 with lower buffing wheel.

Lower hex bolt has regular threads.

Model G0774 (Mfd. Since 10/18)

Adjusting Limit

Switches

Two adjustable limit switches trigger the guillotine and the end trimmer. The switches are factory set, and should not require routine adjustment.

However, after prolonged use, or if your edgebanding results are unsatisfactory, the switches may need to be adjusted.

Item(s) Needed Qty

Hex Wrench 3mm .............................................. 1

Adjusting Guillotine Limit Switch

When the workpiece passes over the guillotine limit switch (see Figure 83), the guillotine severs the edgebanding, leaving a portion of excess that is then trimmed flush by the flush trimmer. If the guillotine leaves too much or too little excess edgebanding, you will need to adjust the switch.

Guillotine

Switch

Adjustment

Screws

Figure 83. Location of guillotine limit switch and adjustment screws.

To adjust guillotine limit switch:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Loosen adjustment screws (see Figure 83).

— If guillotine does not leave enough excess edgebanding, move switch toward infeed table, then retighten adjustment screws.

— If guillotine leaves too much excess edgebanding, move switch toward outfeed table, then retighten adjustment screws.

-55-

Adjusting End Trimmer Switch

When the workpiece passes over the end trimmer switch (see Figure 84), the end trimmer trims the leading and trailing ends of the glued edgebanding flush with the ends of the workpiece. If the end trimmer fails to trim the edgebanding flush with the ends of the workpiece, you will need to adjust the switch.

End Trimmer

Switch

Adjustment

Screws

Figure 84. Location of end trimmer switch and adjustment screws.

To adjust end trimmer switch:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Loosen adjustment screws (see Figure 84).

— If end trimmer leaves too much edgebanding on the leading end of workpiece edge and not enough on the trailing end, move switch toward infeed table, then retighten adjustment screws.

— If end trimmer leaves too much edgebanding on the trailing end of workpiece edge and not enough on the leading end, move switch toward outfeed table, then retighten adjustment screws.

Checking/Adjusting

Conveyor Belt

Tension

The conveyor belt must be properly tensioned for the panel feeder to properly feed workpieces during operations. The conveyor belt tension is factory set and should not require routine adjustment. However, after prolonged use, or if the panel feeder fails to adequately feed workpieces, you will need to adjust the conveyor belt tension.

Item(s) Needed Qty

Hex Wrench 6mm .............................................. 1

To check/adjust conveyor belt tension:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Unlock and open panel feeder.

3. Place 8kg (17 1 ⁄

lbs.) of downward force on conveyor belt, as illustrated in label on panel feeder (see Figure 85).

— If there is 3cm (1 1 ⁄

") of deflection, conveyor belt is properly tensioned and no adjustment is necessary.

— If there is not 3cm (1 1 ⁄

") of deflection, conveyor belt is not properly tensioned and requires adjustment. Proceed to Step 4.

-56-

Figure 85. Conveyor belt tension label, located on inside of panel feeder.

Model G0774 (Mfd. Since 10/18)

4. Rotate conveyor belt tension screw, shown in

Figure 86, to adjust belt tension.

— Rotate screw clockwise to tighten conveyor belt.

— Rotate screw counterclockwise to loosen conveyor belt.

Adjusting Pressure Roller

Checking/Adjusting

Pressure Roller Unit

The pressure roller unit consists of two rollers — one fixed and one adjustable—that apply pressure to the edgebanding against the workpiece immediately after the glue is applied (see Figure 87).

Tension Screw

Figure 86. Location of conveyor belt tension screw.

5. Repeat Steps 3–4, as necessary, until conveyor belt is properly tensioned.

6. Close and lock panel feeder.

Fixed

Pressure

Roller

Adjustable

Pressure

Roller

Figure 87. Location of fixed and adjustable pressure rollers

The fixed, non-adjustable roller applies constant pressure to the edgebanding, while the adjustable roller is spring-loaded, allowing for pressure adjustment.

The adjustable pressure roller is set at the factory and should not require routine service. However, if the pressure roller unit causes too much glue to squeeze out during operations, or if you are getting poor bonding results, you may need to adjust the pressure roller.

Properly adjusting the pressure roller unit is largely a matter of trial and error. Your results may vary depending on the glue type, glue temperature, workpiece thickness, and edgebanding thickness. Always use a test piece to verify your settings after adjusting the pressure roller unit.

Model G0774 (Mfd. Since 10/18) -57-

Item(s) Needed Qty

Open-End Wrench 10mm .................................. 1

Scrap Workpiece at Least 35" Long .................. 1

To check/adjust pressure roller unit:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Set infeed fence to "0" (refer to Page 36).

3. Align glue spindle to infeed fence (refer to

Page 37).

4. Place straight "factory edge" of workpiece against fence, press workpiece against glue spindle, causing spindle to retract. Adjustable pressure roller should keep workpiece approximately 0.040" (1mm) away from fixed pressure roller.

5. Push workpiece against adjustable pressure roller, toward back of machine, until workpiece contacts both pressure rollers and entire fence along its length (see Figure 88).

Because adjustable pressure roller is springloaded, Step 5 should require moderate force.

Fixed

Pressure

Roller

Adjustable

Pressure

Roller

6. Open rear access door.

7. Loosen jam nut shown in Figure 89.

8. Rotate pressure roller adjustment bolt shown in Figure 89.

— Rotate bolt clockwise to move pressure roller away from workpiece and reduce pressure.

— Rotate bolt counterclockwise to move pressure roller toward workpiece and

increase pressure.

Adjustable

Pressure

Roller

Jam Nut

Pressure Roller

Adjustment Bolt

Figure 89. Pressure roller adjustment components (viewed from rear of machine).

9. Repeat Steps 5 & 8 until satisfied with adjustment, then retighten jam nut from Step 7 to secure setting, and close rear access door.

10. Run a test piece of the same material and thickness as your intended workpiece through edgebander to verify satisfactory results. If necessary, repeat Steps 1–10.

Approx. 0.040"

(1mm) Gap

Glue

Spindle

Infeed

Fence

Figure 88. Workpiece placed against infeed fence and pressure roller unit.

— If Step 5 requires moderate force, pressure roller unit is properly adjusted and no further steps are necessary.

— If Step 5 requires excessive force, or if workpiece does not contact adjustable pressure roller at all, pressure roller unit is not properly adjusted. Proceed to Step 6.

-58Model G0774 (Mfd. Since 10/18)

Checking/Adjusting End Trimmer Tracers

Checking/Adjusting

End Trimmer Tracers

Two end- rimmer tracers (left and right) orient the end trimmer blades to the workpiece in order to precisely trim the edgebanding flush with the leading and trailing ends of the workpiece (see

Figure 90).

Item(s) Needed Qty

Hex Wrench 3mm .............................................. 1

Scrap Workpiece at Least 35" Long .................. 1

To check/adjust end trimmer tracers:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Open panel feeder.

3. Place straight "factory edge" of workpiece on infeed table, making sure workpiece contacts entire infeed fence along its length, as shown in Figure 91.

Figure 90. Location of end trimmer tracers.

The end trimmer tracers are factory set and should not require routine service. However, after prolonged use, or if the end trimmer fails to produce satisfactory results, you may need to adjust the end trimmer tracers.

Figure 91. Workpiece placed on infeed table.

Model G0774 (Mfd. Since 10/18) -59-

4. Manually raise and move end trimmer so right end trimmer tracer contacts leading edge of workpiece, as shown in Figures 92–93, then raise and lower end trimmer to verify right end trimmer blade is aligned with right tracer

(see Figure 93).

End Trimmer

Tracer Contacting

Workpiece

5. Rotate both screws shown in Figure 94 in or out, in equal amounts to bring tracer into alignment with blade.

— For right end trimmer tracer, tighten screws to move tracer left; loosen screws to move tracer right.

— For left end trimmer tracer, loosen screws to move tracer left; tighten screws to move tracer right.

Figure 92. Checking alignment of right end trimmer blade.

End Trimmer

Blades

Tip of Tooth

Aligned With

Tracer

End Trimmer

Tracers

Workpiece

Figure 93. End trimmer alignment.

— If blade is aligned to tracer, then no adjustment is necessary.

— If blade is not aligned with tracer, then tracer must be adjusted. Proceed to

Step 5.

Figure 94. Location of right end trimmer tracer adjustment screws.

6. Place workpiece on table to left of end trimmer unit, then repeat Steps 4–5 for left end trimmer tracer.

Note: Belleville disc washers provide spring tension between tracers and copy plate bracket. DO NOT back screw all the way out or it may shoot out and get lost.

7. Run a test piece through edgebander to verify adjustment. Repeat Steps 1–7 until satisfied with results.

-60Model G0774 (Mfd. Since 10/18)

Checking/Adjusting End Trimmer Belt

Checking/Adjusting

End Trimmer

Drive Belt Tension

The end trimmer motor transfers power through a cogged drive belt ( Grizzly Part #P07741329).

The belt should be periodically checked for proper tension and, if necessary, replaced.

Item(s) Needed Qty

Hex Wrench 4mm (Long Handle) ...................... 1

Hex Wrench 5mm .............................................. 1

To check/adjust end trimmer drive belt tension:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Open rear access door.

3. Remove (2) M5-.8 x 12 cap screws with flat washers from end-trimmer belt cover, then remove cover (see Figure 95).

x 2

Note: If belt cover is attached to motor cord with a cable tie, you can leave it attached.

Just slide belt cover along cord after removing it from motor, as shown in Figure 96.

Belt Cover

Attached to

Motor Cord with

Cable Tie

Belt

Figure 96. End trimmer belt cover removed.

4. Apply moderate pressure to belt to see how much it deflects (see Figure 97).

— If belt deflects approximately 1 ⁄

", it is properly tensioned and no adjustment is necessary.

— If belt does not deflect approximately 1 ⁄

", it is not properly tensioned and requires adjustment proceed to Step 6.

Pulley

Belt Cover

Figure 95. Location of cap screws that secure end trimmer belt cover.

Deflection

1/4"

Pulley

Figure 97. End trimmer belt deflection.

Model G0774 (Mfd. Since 10/18) -61-

5. Loosen—but do not remove—cap screws that secure end trimmer belt tension plate

(see Figure 98).

IMPORTANT: Do not remove these screws.

If you do, it will be difficult to re-install end trimmer belt tension plate.

Belt Tension

Plate x 2 ensioning End Trimmer Belt mount cap screws (see Figure 100).

In this position, insert wrench through belt tension plate

Figure 98. Location of cap screws that secure end trimmer belt tension plate.

6. Rotate end trimmer motor pulley by hand until adjustment hole aligns with one of four motor mount cap screws (see Figure 99).

7. Insert long-handled hex wrench into adjustment hole, as shown in Figure 99, and loosen—but do not remove—motor mount cap screw.

IMPORTANT: Do not remove this screw. If you do it will be very difficult to re-install.

Adjustment

Hole

Motor Mount

Cap Screw

Figure 99. Loosening one of four end trimmer motor mount cap screws.

-62-

Figure 100. Loosening remaining end trimmer motor mount cap screws.

9. Shift motor up or down with one hand while checking belt deflection with other hand.

When belt deflection is approximately 1 ⁄

", tighten one of four motor mount cap screws from Steps 6–7.

10. Check belt deflection again and, if necessary, re-adjust it, then tighten remaining motor mount cap screws from Steps 6–7.

11. Retighten cap screws from Step 5, then reinstall belt cover, and close rear access door.

Model G0774 (Mfd. Since 10/18)

Replacing End Trimmer Belt

Replacing

End Trimmer Drive

Belt

If the end trimmer drive belt becomes worn, cracked, frayed, broken, or otherwise damaged, you will need to replace it with a new one ( Grizzly

Part #P07741329).

Item(s) Needed Qty

Hex Wrench 4mm (Long Handle) ...................... 1

Hex Wrench 5mm .............................................. 1

To replace end trimmer drive belt:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Remove end trimmer belt cover and adjust motor to loosen belt (refer to Steps 3–7 of Checking/Adjusting End Trimmer Belt

Tension, beginning on Page 61).

3. Remove old belt and install new belt.

4. Properly tension belt and re-install belt cover

(refer to Steps 9–11 of Checking/Adjusting

End Trimmer Belt Tension, on Page 62).

Replacing Flush Trimmer Belt

Replacing Flush

Trimmer Drive Belt

The flush trimming motor transfers power through a serpentine drive belt (see Figure 101). The belt is tensioned automatically by the weight of the motor and does not require adjustment.

However, if it becomes worn, cracked, frayed, broken, or otherwise damaged in any way, you will need to replace it with a new one ( Grizzly

Part #P07740627).

Drive

Belt

Figure 101. Location of flush trimmer drive belt.

Item(s) Needed Qty

Hex Wrench 5mm .............................................. 1

Wood Block 4" x 4" x 6" .................................... 1

To replace flush trimmer drive belt:

1. DISCONNECT MACHINE FROM POWER

AND AIR!

2. Lower panel feeder all the way (see Page 35).

Model G0774 (Mfd. Since 10/18) -63-

3. Open rear access door.

4. Loosen cap screw shown in Figure 102.

Belt Section End making sure to properly route it around pulleys, as shown in Figure 104.

Flush Trimmer

Motor Pulley

Upper Flush

Trimmer Pulley

Lower Flush

Trimmer Pulley

Figure 102. Location of cap screw to loosen when changing flush trimmer drive belt.

5. Raise motor by hand, then support it with a

4" x 4" x 6" wood block to release belt tension

(see Figure 103).

Flush Trimmer

Motor

Belt Tension

Released

Figure 104. Flush trimmer drive belt properly routed around pulleys.

7. Raise motor by hand, then remove wood block from Step 5.

8. Press down on motor slightly, making sure motor contact bar shown in Figure 105 drops down and contacts motor, then tighten cap screw from Step 4.

Wood

Block

Figure 103. Flush trimmer motor raised and supported on wood block to release belt tension.

Motor Contact

Bar

Figure 105. Location of motor contact bar.

9. Close rear access door.

-64Model G0774 (Mfd. Since 10/18)

machine

SECTION 8: WIRING

These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully.

If there are differences between your machine and what is shown in this section, call Technical Support at

(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated wiring diagram may be available. Note: Please gather the serial number and manufacture date of your machine before calling. This information can be found on the main machine label.

Wiring Safety Instructions

SHOCK HAZARD. Working on wiring that is connected to a power source is extremely dangerous.

Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before servicing electrical components!

MODIFICATIONS. Modifying the wiring beyond what is shown in the diagram may lead to unpredictable results, including serious injury or fire.

This includes the installation of unapproved aftermarket parts.

WIRE/COMPONENT DAMAGE. Damaged wires or components increase the risk of serious personal injury, fire, or machine damage. If you notice that any wires or components are damaged while performing a wiring task, replace those wires or components.

MOTOR WIRING. The motor wiring shown in these diagrams is current at the time of printing but may not match your machine. If you find this to be the case, use the wiring diagram inside the motor junction box.

WIRE CONNECTIONS. All connections must be tight to prevent wires from loosening during machine operation. Double-check all wires disconnected or connected during any wiring task to ensure tight connections.

CAPACITORS/INVERTERS. Some capacitors and power inverters store an electrical charge for up to 10 minutes after being disconnected from the power source. To reduce the risk of being shocked, wait at least this long before working on capacitors.

CIRCUIT REQUIREMENTS. You MUST follow the requirements at the beginning of this manual when connecting your machine to a power source.

EXPERIENCING DIFFICULTIES. If you are experiencing difficulties understanding the information included in this section, contact our Technical

Support at (570) 546-9663.

-65Model G0774 (Mfd. Since 10/18)

Electrical Panel Wiring Diagram

-66-

READ ELECTRICAL SAFETY

ON PAGE 65!

Model G0774 (Mfd. Since 10/18)

Electrical Panel Photos

Figure 106. Electrical panel.

Figure 107. Electrical panel detail—center.

Figure 108. Electrical panel detail—leftside.

Figure 109. Electrical panel detail—rightside.

Model G0774 (Mfd. Since 10/18)

READ ELECTRICAL SAFETY

ON PAGE 65!

-67-

Terminal Block Wiring Diagram

-68-

READ ELECTRICAL SAFETY

ON PAGE 65!

Model G0774 (Mfd. Since 10/18)

Motor Wiring Diagram

Glue Spindle Motor 220V 1-Phase Conveyor Motor 220V 1-Phase

Upper Buffing Motor 220V 1-Phase Flush Trimmer Motor 220V 1-Phase

Lower Buffing Motor 220V 1-Phase End Trimmer Motor 220V 1-Phase

Model G0774 (Mfd. Since 10/18)

READ ELECTRICAL SAFETY

ON PAGE 65!

-69-

Motor Photos

Figure 110. Glue spindle motor wiring.

Figure 113. Conveyor motor wiring.

Figure 111. Upper buffing motor wiring.

Figure 114. Flush trimmer motor wiring.

-70-

Figure 112. Lower buffing motor wiring.

READ ELECTRICAL SAFETY

ON PAGE 65!

Figure 115. End trimmer motor wiring.

Model G0774 (Mfd. Since 10/18)

Control Panel Wiring Diagram

Model G0774 (Mfd. Since 10/18)

READ ELECTRICAL SAFETY

ON PAGE 65!

-71-

Control Panel SEB-E330 Component Key

Relay Contact Postion

Control Panel SEB-E330 (Standby Mode)

-72-

READ ELECTRICAL SAFETY

ON PAGE 65!

Model G0774 (Mfd. Since 10/18)

Pneumatic Valve & Limit Switch Wiring

Diagram

Cutter Trimmer

Limit Switch

End Trimmer

Limit Switch

Pressure Switch

Door

Limit Switch

Door

Limit Switch

Model G0774 (Mfd. Since 10/18)

READ ELECTRICAL SAFETY

ON PAGE 65!

-73-

Electrical Schematics

Circuit Board Schematic

Circuit Board Control Loop SEB-E330 (Standby Mode)

Transformer Secondary Side

FU2

Fuse Horlder

QM1

QM2

QM3

N.O

Temperature Controller

SP1: Air Pressure Switch

SQ1: Swing Arm Disconnect Switch

SQ2:

Transformer Secondary Side

Pressue Beam Bracket Disconnect

Switch

FU3

Fuse Horlder

0(12)

QM4

N.O

QM5

N.O

STOP

SQ1 SQ2

7 8

SP1

Pin13

KA0

Pin14

Control Power

Switch On

1 TH

N.O

TH-AL2

KA1

N.C

Pin9 Pin1

KM6 Heater On

Relay Diagrm

3 2 1

8 7 6 5

12 11 10 9

4 14 13

TH-AL1 13

1(com3)

KA0

Pin11

Pin7

Pin12

Pin8

Y14 Y14

Y15

Y17

KA0

N.O

Pin10 Pin6

KM6

N.O

Solenoid Valve

( Brown) 0(Blue)

Solenoid Valve

12( Brown) 0(Blue)

KM2 Glue Spindle Motor On

KM7

Pin13

KA1

Pin14

Pre-hest On

Lndicator Light for Pre-heat Starting

Stop Cylinder go down

(EV7 Solenoid Valve)

Standby Mode On

Lndicator Light for Standby Mode

Air Pressure On(EV1 Solenoid Valve)

12(com0)

12(com1)

Y10

Y11 Y11

PLC com

C0,C1,C2 connect12

C3connect1

Solenoid Valve

( Brown)

0(Blue)

Solenoid Valve

( Brown) 0(Blue)

Solenoid Valve

( Brown) 0(Blue)

KM1

KM3

KM5

KM4

Lndicator Light for Cutter Cylinder

Lndicator Light for Fron&End

Trimming Cylinder

Conveyor Motor On

Lndicator Light for Conveyor Motor

Fron&End Trimming Motor On

Lndicator Light for Fron&End

Trimming Motor

Upper&Lower Wheel Motor

Lndicator Light for Upper&Lower

Wheel Motor

Cutter Cylinder On(EV2 Solenoid

Valve)

Fron&End Trimming Cylinder Move

Forward(EV3 Solenoid Valve)

Fron&End Trimming Cylinder Move

Down(EV4 Solenoid Valve)

Flush Trimming Motor On

Lndicator Light for Flush Trimming

Motor

-74-

READ ELECTRICAL SAFETY

ON PAGE 65!

Model G0774 (Mfd. Since 10/18)

Power Supply—Main Control Circuit

Main Control Circuit

Model G0774 (Mfd. Since 10/18)

READ ELECTRICAL SAFETY

ON PAGE 65!

-75-

Power Supply—Motor Circuit Breaker

Motor Ciruit Breaker

-76-

READ ELECTRICAL SAFETY

ON PAGE 65!

Model G0774 (Mfd. Since 10/18)

Power Supply—Transformer & Heater

Model G0774 (Mfd. Since 10/18)

Transformer & Heater

READ ELECTRICAL SAFETY

ON PAGE 65!

-77-

Power Supply—PLC Input

-78-

READ ELECTRICAL SAFETY

ON PAGE 65!

PLC Input

GND

Model G0774 (Mfd. Since 10/18)

Power Supply—PLC Output

PLC Output

Model G0774 (Mfd. Since 10/18)

READ ELECTRICAL SAFETY

ON PAGE 65!

-79-

SECTION 9: PNEUMATIC SYSTEM

-80-

This diagram is only provided as a reference to help you identify pneumatic system components. Seek assistance from a professional pneumatic technician whenever servicing or repairing the pneumatic system.

Model G0774 (Mfd. Since 10/18)

SECTION 10: PARTS

We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability.

Parts Reference Page

Panel Feeder

Page 86

Panel Feeder Elevation

Page 85

Panel Feeder Lock

Page 87

Control Panel

Page 82

Coil Support

Page 90

Heated Fence

Page 93

Cover Panels

Page 84

Main Table

Page 82

Edgebanding Feeder

Page 94

Pressure Roller

Page 92

Vertical Edgebanding Guide &

Glue Spindle Page 97

Glue Pot Cover

Glue Pot

Page 98

Page 99

End Trimmer Carriage Page 95

End Trimmer Motor Page 96

Edgebanding Intake

Assembly Page 91

Upper & Lower Buffing

Motors Page 101

Glue Spindle Motor

Page 100

Electrical Panel

Page 104

Model G0774 (Mfd. Since 10/18)

Upper Flush Trimmer

Page 102

Lower Flush Trimmer

Page 103

Pneumatic Guillotine

Page 88

Flush Trimmer

Motor Page 89

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-81-

parts main table

Main Table

36-1

55 42 41

25 69 14

29-1

-82BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0774 (Mfd. Since 10/18)

Main Table Parts List

REF PART # DESCRIPTION

P07740001 EXTENSION BRACKET

P07740002 ROLLER SKID 78-1/2 X 3/4 X 3/4"

P07740003 FLAT WASHER 8MM

P07740004 WHEEL SEAT 9"

P07740005 CABINET BODY

P07740006 FENCE PLATE (NOTCHED)

P07740007 LIMIT SWITCH SNZ AZD-S11 2A 400V

P07740008 STRAIN RELIEF TYPE-1 PG9 (1PC)

P07740009 STRAIN RELIEF TYPE-1 PG13.5 (1PC)

P07740010 PRESSURE SWITCH DANFOSS KP36

P07740011 ELECTRICAL PANEL ASSEMBLY

P07740012 FLANGE NUT M8-1.25

P07740013 BUTTON HD CAP SCR M8-1.25 X 25

P07740014 CAP SCREW M6-1 X 16

P07740015 CAP SCREW M8-1.25 X 30

P07740016 MAGNETIC CATCH

P07740017 ELECTRICAL PANEL DOOR (L)

P07740018 ELECTRICAL PANEL DOOR (R)

P07740019 WORKPIECE SUPPORT BAR

P07740020 ELECTRICAL PANEL DOOR LOCK

P07740021 BUTTON HD CAP SCR M5-.8 X 10

P07740022 FLAT WASHER 5MM

P07740023 BRUSH

P07740024 BUTTON HD CAP SCR M5-.8 X 20

P07740025 FLAT WASHER 10MM

P07740026 NYLON BOX CONNECT N-MGN16-15B-ST

P07740027 HEX BOLT M6-1 X 25

P07740028 PRESSURE REGULATOR ASSY

P07740029 SOLENOID FONRAY 4V210-08H 0.15-.8MP

29-1 P07740029-1 SOLENOID AMISCO E343908 24V 4.5A

30 P07740030 FILTER/LUBRICATOR/REG FONRAY 1508

P07740031 WIRING JUNCTION BOX

P07740032 CAP SCREW M6-1 X 12

P07740033 LOCK WASHER 6MM

P07740034 PHLP HD SCR M4-.7 X 30

P07740035 PHLP HD SCR M4-.7 X 15

P07740036 ROTARY SWITCH ZH-HD-2

36-1 P07740036-1 CORD 3W 12G 16"

37 P07740037 SWITCH BOX

38 P07740038 EXTENSION BRACKET BLOCK

REF PART #

DESCRIPTION

P07740039 BUSHING

P07740040 EXTENSION ROD 21 X 3/4"

P07740041 FENDER WASHER 8MM

P07740042 LOCK WASHER 8MM

P07740043 HEX BOLT M8-1.25 X 12

P07740044 CAP SCREW M6-1 X 20

P07740045 FLAT WASHER 6MM

P07740046 EXTENSION SUPPORT ROLLER

P07740047 BUTTON HD CAP SCR M5-.8 X 40

P07740048 LOCK NUT M5-.8

P07740049 PHLP HD SCR M6-1 X 12

P07740050 CAP SCREW M6-1 X 25

P07740051 HEX NUT M6-1

P07740052 CONTROL PANEL BACKPLATE

P07740053 FLAT WASHER 8MM

P07740054 CAP SCREW M8-1.25 X 12

P07740055 BUTTON HD CAP SCR M8-1.25 X 16

P07740056 WAVE TUBE N-MGN32-34B

P07740057 SET SCREW M8-1.25 X 8

P07740059 EXTENSION TABLE LEG

P07740060 HEX NUT M12-1.75

P07740061 ADJUSTABLE FOOT M12-1.75 X 75

P07740062 SET SCREW M6-1 X 16

P07740063 STRAIN RELIEF TYPE-3 PG20

P07740064 CAP SCREW M6-1 X 12

P07740065 LOCK WASHER 6MM

P07740066 OUTFEED SKID BAR 14 X 3/4 X 1" METAL

P07740067 MOTOR CONTACT BAR

P07740068 CAP SCREW M8-1.25 X 20

P07740069 ROLLER 100 X 20MM

P07740070 NEEDLE BEARING HK1010

P07740071 CONTROL PANEL COVER

P07740072 BUTTON HD CAP SCR M5-.8 X 10

P07740073 WAVE TUBE N-MGN32-34B

P07740074 CONDUIT 1-3/8" X 32"

P07740076 FLAT WASHER 6MM

P07740077 LIMIT SWITCH SNZ AZD-S11 2A 400V

P07740078 POWER CORD 12G 3W 72" L6-30P

P07740079 TERMINAL BLOCK 4P

Model G0774 (Mfd. Since 10/18) BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-83-

parts cover panels

103

104

114

122

115

134

119

Cover Panels

103

104

127

133

131

112

130

107

113

128

129

121

125

126

120

110

135

108

102

110

109

119

132

116

105

111

124

123

117

106

118

101

REF PART # DESCRIPTION

101 P07740101 REAR ACCESS PANEL

102 P07740102 CAP SCREW M6-1 X 12

103 P07740103 HINGE

104 P07740104 RIVET 3.2 X 8.9 BLIND

105 P07740105 CLEAR COVER

106 P07740106 REAR COVER HANDLE

107 P07740107 LIMIT SWITCH ASSY AZD-S11

108 P07740108 LOCK NUT M6-1

109 P07740109 KNOB 10-LOBE 60MM

110 P07740110 CAP SCREW M6-1 X 25

111 P07740111 REAR COVER (UPPER)

112 P07740112 MAGNETIC CATCH

113 P07740113 FRONT COVER (UPPER)

114 P07740114 PANEL FEEDER COVER

115 P07740115 PANEL FEEDER HOUSING

116 P07740116 TOP COVER

117 P07740117 FLANGE NUT M8-1.25

118 P07740118 CAP SCREW M8-1.25 X 16

REF PART # DESCRIPTION

119 P07740119 BUTTON HD CAP SCR M5-.8 X 8

120 P07740120 HEX NUT M6-1

121 P07740121 HINGE PLATE

122 P07740122 DO NOT LEAN LABEL

123 P07740123 FLANGE BOLT M6-1 X 8

124 P07740124 RIVET 3.2 X 8.9 BLIND

125 P07740125 CAP SCREW M5-.8 X 12

126 P07740126 HINGE

127 P07740127 CONDUIT 2.5" X 25"

128 P07740128 CONDUIT 2.5" X 36"

129 P07740129 CONDUIT 2.5" X 46"

130 P07740130 BUTTON HD CAP SCR M4-.7 X 35

131 P07740131 FLANGE NUT M4-.7

132 P07740132 FLANGE BOLT M5-.8 X 8

133 P07740133 CABLE TIE (WHITE)

134 P07740134 FLAT WASHER 5MM

135 P07740135 FRONT COVER (LOWER)

-84BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0774 (Mfd. Since 10/18)

parts panel feeder elevation

Panel Feeder Elevation

223

227

225

228

229

211

237

236

234

235

201

223

213

218

220

212

222

224

219

206

202

204

203

216

217

204

202

205

208

207

214

215

230

226

231

232

209

REF PART # DESCRIPTION

201 P07740201 PRESSURE BEAM BRACKET

202 P07740202 THRUST BEARING 51201

203 P07740203 STUD-SE M14-1.5 X 115

204 P07740204 BEARING SLEEVE BUSHING

205 P07740205 HEX NUT M12-1.75

206 P07740206 ADAPTER SHAFT

207 P07740207 BEARING SLEEVE

208 P07740208 BEARING CAP

209 P07740209 SLIDER BRACKET

211 P07740211 HANDWHEEL 2-SPOKE 165MM W/HANDLE

212 P07740212 SET SCREW M8-1.25 X 10

213 P07740213 POSITION INDICATOR

214 P07740214 SLIDER RING

215 P07740215 SHOULDER BOLT M14-1.25 X 15, 25L

216 P07740216 SHAFT SEAT M14-1.5

217 P07740217 COLUMN

218 P07740218 CAP SCREW M5-.8 X 45

Model G0774 (Mfd. Since 10/18)

REF PART # DESCRIPTION

219 P07740219 LOCK NUT M5-.8

220 P07740220 ROLL PIN 5 X 20

222 P07740222 HEX BOLT M8-1.25 X 40

223 P07740223 HEX BOLT M8-1.25 X 30

224 P07740224 LOCK WASHER 8MM

225 P07740225 SET SCREW M8-1.25 X 16

226 P07740226 CAP SCREW M8-1.25 X 30

227 P07740227 HEX NUT M8-1.25

228 P07740228 HEX NUT M8-1.25 THIN

229 P07740229 HEX BOLT M8-1.25 X 12

230 P07740230 COUNTER ARM SUPPORT

231 P07740231 SUPPORT ARM PLATE

232 P07740232 FLAT HD CAP SCR M6-1 X 25

234 P07740234 PRESSURE BEAM FIXED PLATE

235 P07740235 FLAT WASHER 20MM

236 P07740236 FLAT HD CAP SCR M8-1.25 X 12

237 P07740237 SET SCREW M5-.8 X 6

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-85-

parts panel feeder

Panel Feeder

345

325

314

324

306

334

332

323

312

321

322

335

333

331

305

312

320

311

307

308

328

317

313

319-1

319-2

319

329

319-5 319-6

319-7

319-10

319-4 319-8

319-9

330

318

316

326

340 341

343

342

343

344

315

301

310

336

347

346

339

337

338

302

327

303

304

309

REF PART # DESCRIPTION

301

302

303

304

305

306

307

308

309

310

311

P07740301

P07740302

P07740303

P07740304

P07740305

P07740306

P07740307

P07740308

P07740309

P07740310

P07740311

CONVEYOR BODY

CONVEYOR BASE PLATE

BELT IDLER ROLLER 70 X 60MM, PLASTIC

ROLLER BUSHING

BELT DRIVE ROLLER 70 X 60MM, PLASTIC

KEYED SHAFT

KEY 6 X 6 X 20

KEY 6 X 6 X 40

ROLLER SHAFT

CAP SCREW M8-1.25 X 80

EXT RETAINING RING 18MM

312

313

314

315

316

P07740312

P07740313

P07740314

P07740315

P07740316

DRIVE ROLLER GASKET

GEARBOX NMRV040

REDUCER FLANGE

HEX BOLT M8-1.25 X 90

FLAT WASHER 8MM

317

318

P07740317

P07740318

FLANGE NUT M8-1.25

CONVEYER BELT (RUBBER)

319 P07740319 MOTOR 3/4HP 220V 1-PH (PANEL FEEDER)

319-1 P07740319-1 MOTOR FAN COVER

319-2 P07740319-2 MOTOR FAN

319-4 P07740319-4 R CAPACITOR 30MFD 250V

319-5 P07740319-5 MOTOR JUNCTION BOX

319-6 P07740319-6 CONTACT PLATE

319-7 P07740319-7 CENTRIFUGAL SWITCH

319-8 P07740319-8 BALL BEARING 6203ZZ (FRONT)

319-9 P07740319-9 BALL BEARING 6202ZZ (REAR)

319-10 P07740319-10 S CAPACITOR 150MFD 250V

REF PART # DESCRIPTION

320 P07740320 BALL BEARING 6301-2RS

321 P07740321 SET SCREW M6-1 X 30

322 P07740322 FENDER WASHER 6 X 23 X 3MM

323 P07740323 HEX NUT M6-1

324 P07740324 BUTTON HD CAP SCR M6-1 X 20

325 P07740325 HEX BOLT M6-1 X 20

326 P07740326 CAP SCREW M8-1.25 X 40

327 P07740327 FLAT WASHER 20 X 30 X .5MM

328 P07740328 WAVE TUBE N-MGN16-15B-ST

329 P07740329 CONDUIT 30" NGN-12B-50 RIBBED

330 P07740330 MOTOR CORD 16G 4W 40"

331 P07740331 BUSHING

332 P07740332 BEARING PLATE

333 P07740333 BALL BEARING 6904-2RS

334 P07740334 CAP SCREW M6-1 X 20

335 P07740335 INT RETAINING RING 37MM

336 P07740336 PNEUMATIC STOP PISTON

337 P07740337 STOP PISTON BRACKET

338 P07740338 STOP (RUBBER)

339 P07740339 HEX NUT M8-1.25

340 P07740340 HEX NUT M6-1

341 P07740341 BRUSH MOUNTING BRACKET

342 P07740342 BRUSH

343 P07740343 FLAT WASHER 6MM

344 P07740344 CAP SCREW M6-1 X 25

345 P07740345 CONVEYOR MOUNTING BLOCK

346 P07740346 BUTTON HD CAP SCR M5-.8 X 10

347 P07740347 FLAT WASHER 4MM

-86BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0774 (Mfd. Since 10/18)

parts panel feeder lock

410

403

Panel Feeder Lock

412

409

417

417-1

416

402

408

419

421422

408 408

402

406

411

423

405

420

407

409

410

414

415

404

403

401

418

413

REF PART # DESCRIPTION

401 P07740401 ADJUSTMENT COLUMN

402 P07740402 FLAT WASHER 4MM

403 P07740403 LOCK WASHER 8MM

404 P07740404 CAP SCREW M8-1.25 X 20

405 P07740405 CONVEYOR LOCK BRACKET

406 P07740406 SWITCH CONTACT PLATE

407 P07740407 HEX NUT M6-1

408 P07740408 PHLP HD SCR M4-.7 X 8

409 P07740409 PHLP HD SCR M8-1.25 X 40

410 P07740410 FLAT WASHER 8MM

411 P07740411 ADJUSTMENT BRACKET

412 P07740412 DOOR SWITCH MOUNTING PLATE

REF PART # DESCRIPTION

413 P07740413 FLAT HD CAP SCR M10-1.5 X 35

414 P07740414 FLAT WASHER 10 X 20 X 2MM

415 P07740415 WAVY WASHER 10MM

416 P07740416 PHLP HD SCR M4-.7 X 30

417 P07740417 LIMIT SWITCH AZDS11

417-1 P07740417-1 LIMIT SWITCH KEY

418 P07740418 ADJUSTABLE HANDLE M10-1.5 X 35, 92L

419 P07740419 FENDER WASHER 10 X 27 X 4MM

420 P07740420 HEX BOLT M6-1 X 30

421 P07740421 WAVY WASHER 10MM

422 P07740422 FLAT WASHER 10MM

423 P07740423 LOCK BRACKET BLOCK

Model G0774 (Mfd. Since 10/18) BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-87-

parts pneumatic guillotine

Pneumatic Guillotine

516

500

520

517

507

514

520

515

518

502

503

509 513

510

511

520

512

519

506

505 501

521

520

522

504

508

REF PART # DESCRIPTION

500 P07740500 GUILLOTINE ASSEMBLY

501 P07740501 CUTTER GUIDE PLATE

502 P07740502 CUTTER MOUNTING BLOCK

503 P07740503 CUTTER SUPPORT PLATE

504 P07740504 CUTTER ALIGNMENT PLATE

505 P07740505 LOCATE BLOCK

506 P07740506 CUTTER

507 P07740507 CYLINDER MOUNTING PLATE

508 P07740508 FLAT HD CAP SCR M6-1 X 16

509 P07740509 FLAT HD CAP SCR M6-1 X 20

510 P07740510 FLAT HD CAP SCR M6-1 X 12

511 P07740511 CAP SCREW M6-1 X 35

REF PART # DESCRIPTION

512 P07740512 LOCK NUT M6-1

513 P07740513 FLAT HD CAP SCR M6-1 X 25

514 P07740514 PNEUMATIC CYLINDER ASSEMBLY

515 P07740515 SET SCREW M10-1.5 X 90

516 P07740516 HEX BOLT M6-1 X 70

517 P07740517 FLAT WASHER 6MM

518 P07740518 HEX NUT M10-1.5

519 P07740519 ROLL PIN 4 X 12

520 P07740520 LOCK WASHER 6MM

521 P07740521 CAP SCREW M6-1 X 20

522 P07740522 FENDER WASHER 6MM

-88BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0774 (Mfd. Since 10/18)

parts flush trimmer motor

Flush Trimmer Motor

600

617

601

617

604

630

616

617 607

603

622

620

624

602

624

619

610

609

608

621

625 626

605

628

REF PART # DESCRIPTION

600

601

602

603

604

605

606

607

P07740600

P07740601

P07740602

P07740603

P07740604

P07740605

P07740606

P07740607

FLUSH TRIMMER MOTOR ASSEMBLY

COLUMN SEAT

HEIGHT ROD

HEIGHT ROD LOCK PLATE (UPPER)

HEIGHT ROD LOCK PLATE (LOWER)

MOTOR MOVEMENT PLATE

MOTOR BLOCK

MOTOR MOUNTING BRACKET

608

609

P07740608

P07740609

LOCK COLLAR

COMPRESSION SPRING 7 X 22 X 1.5

610 P07740610 CAP SCREW M6-1 X 10

611 P07740611 MOTOR 3/4HP 220V 1-PH (TRIM ROUTER)

611-1 P07740611-1 MOTOR FAN COVER

611-2 P07740611-2 MOTOR FAN

611-4 P07740611-4 R CAPACITOR 30MFD 250V

611-5 P07740611-5 MOTOR JUNCTION BOX

611-6 P07740611-6 CONTACT PLATE

611-7 P07740611-7 CENTRIFUGAL SWITCH

611-8 P07740611-8 BALL BEARING 6203ZZ (FRONT)

611-9 P07740611-9 BALL BEARING 6202ZZ (REAR)

612

629

611

616 617

618

631

615

627

606

614

613

628

611-1

611-2

611-4

611-10

611-5 611-6

611-7

611-8 611-9

REF PART # DESCRIPTION

625

626

627

628

629

630

631

619

620

621

622

624

611-10 P07740611-10 S CAPACITOR 150MFD 250V

612 P07740612 FLAT BELT PULLEY

613

614

P07740613

P07740614

CAP SCREW M5-.8 X 16

FLAT WASHER 5MM

615

616

617

618

P07740615

P07740616

P07740617

P07740618

LINEAR BEARING LM12UU

CAP SCREW M6-1 X 16

LOCK WASHER 6MM

FLAT WASHER 6MM

P07740619

P07740620

P07740621

P07740622

P07740624

HEX BOLT M8-1.25 X 25

LOCK WASHER 8MM

FLAT WASHER 8MM

SET SCREW M6-1 X 6

CAP SCREW M6-1 X 25

P07740625

P07740626

P07740627

P07740628

P07740629

P07740630

P07740631

FLAT WASHER 13MM

HEX NUT M6-1

BELT 20 X 730MM

FLAT WASHER 6 X 19 X 2MM

MOTOR CORD 16G 3W 12"

SET SCREW M6-1 X 20

INT RETAINING RING R21

Model G0774 (Mfd. Since 10/18) BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-89-

parts coil support

Coil Support

713

718

705

710

704

709

703

700

708

702

711

713

712

701

717

716 715

714

715 716 717

708

705

706

707

705 706

REF PART # DESCRIPTION

700 P07740700 COIL SUPPORT ASSEMBLY

701 P07740701 SUPPORT ARM

702 P07740702 COIL SUPPORT

703 P07740703 ROLLER LOCK PLATE M8-1.25

704 P07740704 BANDING TENSION ROLLER 40 X 25MM

705 P07740705 FENDER WASHER 10MM

706 P07740706 HEX NUT M10-1.5

707 P07740707 STUD-FT M10-1.5 X 150

708 P07740708 BUTTON HD CAP SCR M8-1.25 X 16

709 P07740709 FLAT WASHER 8MM

REF PART # DESCRIPTION

710 P07740710 SHOULDER BOLT M8-1.25 X 12, 14 X 52L

711 P07740711 CAP SCREW M8-1.25 X 20

712 P07740712 FLAT WASHER 8MM

713 P07740713 LOCK WASHER 8MM

714 P07740714 BANDING ROLLER 375 X 40MM

715 P07740715 INT RETAINING RING 32MM

716 P07740716 BALL BEARING 6201ZZ

717 P07740717 BEARING SPACER

718 P07740718 LOCK NUT M10-1.5

-90BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0774 (Mfd. Since 10/18)

parts edgebanding intake assembly

Edgebanding Intake Assembly

800

802

804

809

808

805

807

803

806 801

REF PART #

800 P07740800

801 P07740801

802 P07740802

803 P07740803

804 P07740804

DESCRIPTION

EDGEBANDING INTAKE ASSEMBLY

GUIDE (INNER)

GUIDE (OUTER)

SHOULDER BOLT M5-.8 X 8, 8 X 18

KNOB 4-LOBE M5-.8

REF PART #

805 P07740805

806 P07740806

807 P07740807

808 P07740808

809 P07740809

DESCRIPTION

FLAT WASHER 5MM

HEX BOLT M8-1.25 X 12

FLANGE NUT M8-1.25

FLAT WASHER 6MM

CAP SCREW M6-1 X 10

Model G0774 (Mfd. Since 10/18) BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-91-

parts pressure roller

Pressure Roller

901

925

903

925

904

914

901

919

912

920

913

932

909

913

920

912

905

909

932

911

REF PART # DESCRIPTION

900 P07740900 PRESSURE ROLLER ASSEMBLY

901 P07740901 BEARING PLATE

902 P07740902 WHEEL SUPPORT PLATE

903 P07740903 ROLLER WHEEL 40 X 65MM METAL (OUTER)

904 P07740904 WHEEL SPINDLE 15 X 80MM (OUTER)

905 P07740905 WHEEL SPINDLE 15 X 80MM (INNER)

906 P07740906 T-PLATE SUPPORT BLOCK

907 P07740907 BASE PLATE TOP BLOCK

908 P07740908 FLAT HD CAP SCR M6-1 X 12

909 P07740909 FLAT WASHER 8MM

910 P07740910 CAP SCREW M6-1 X 16

911 P07740911 HEX BOLT M8-1.25 X 20

912 P07740912 INT RETAINING RING 42MM

913 P07740913 EXT RETAINING RING 20MM

914 P07740914 EXT RETAINING RING 15MM

915 P07740915 HEX BOLT M6-1 X 65

916 P07740916 COMPRESSION SPRING 2.5 X 14 X 30

910

929

902

906

928 915

921 922

918

923

907

917

916

908

924

931

929

910

927

926

930

910

933

929

900

REF PART # DESCRIPTION

917 P07740917 FLAT WASHER 6MM

918 P07740918 FENDER WASHER 6 X 16 X 2

919 P07740919 ROLLER WHEEL 79 X 58MM METAL (INNER)

920 P07740920 BALL BEARING 6004LLU

921 P07740921 CLEVIS ROD END

922 P07740922 HEX NUT M6-1

923 P07740923 LOCK NUT M6-1

924 P07740924 BUTTON HD CAP SCR M5-.8 X 8

925 P07740925 SELF-LUBE BEARING DU1520

926 P07740926 BASE PLATE

927 P07740927 SET SCREW M8-1.25 X 8

928 P07740928 BUTTON HD CAP SCR M6-1 X 20

929 P07740929 LOCK WASHER 6MM

930 P07740930 FLAT HD CAP SCR M8-1.25 X 20

931 P07740931 ROLLER SCRAPER

932 P07740932 LOCK WASHER 8MM

933 P07740933 FLAT WASHER 6 X 18 X 2MM

-92BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0774 (Mfd. Since 10/18)

parts heated fence

Heated Fence

1000

1020

1021

1007

1012

1008

1009

1011

1010

1001

1018

1016

1017

1002

1014

1005

1004

1018

1019

1003

REF PART #

1000

1001

1002

1003

1004

1005

1006

1007

1008

1009

1010

P07741000

P07741001

P07741002

P07741003

P07741004

P07741005

P07741006

P07741007

P07741008

P07741009

P07741010

DESCRIPTION

HEATED FENCE ASSEMBLY

FENCE MOUNTING PLATE

LIMIT BLOCK

FENCE SLIDER

SLIDER BLOCK

HEATED FENCE

STUD-DE M8-1.25 X 160, 10

ECCENTRIC KNURLED CYCLINDER

HEATED FENCE COVER

HEATING ELEMENT

HEX BOLT M8-1.25 X 12

1015

1013

1006

REF PART #

1011

1012

1013

1014

1015

1016

1017

1018

1019

1020

1021

P07741011

P07741012

P07741013

P07741014

P07741015

P07741016

P07741017

P07741018

P07741019

P07741020

P07741021

DESCRIPTION

FLAT WASHER 8MM

CAP SCREW M8-1.25 X 55

FLANGE BOLT M5-.8 X 10

LOCK WASHER 8MM

CAP SCREW M5-.8 X 12

CAP SCREW M6-1 X 35

LOCK WASHER 5MM

LOCK WASHER 6MM

CAP SCREW M6-1 X 20

ADJUSTABLE HANDLE M8-1.25, 82L

FENDER WASHER 8 X 30 X 3MM

Model G0774 (Mfd. Since 10/18) BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-93-

parts edgebanding feeder

Edgebanding Feeder

1123

1145

1114

1113

1117

1100

1116

1134

1133

1111

1120

1132

1112

1101

1141

1140

1118

1144

1142

1116

1137

1104

1115

1103

1102

REF PART # DESCRIPTION

1100 P07741100 EDGEBANDING FEEDER ASSEMBLY

1101 P07741101 ROLLER BASE PLATE

1102 P07741102 VERTICAL PLATE

1103 P07741103 PRESSURE WHEEL

1104 P07741104 BEARING PLATE (UPPER)

1105 P07741105 TENSION WHEEL BASE PLATE

1106 P07741106 WHEEL SHAFT

1107 P07741107 STUD-DE M8-1.25 X 30, 82L

1108 P07741108 FLAT HD CAP SCR M8-1.25 X 40

1109 P07741109 TENSION WHEEL 40 X 60MM PLASTIC

1110 P07741110 GEAR

1111 P07741111 FIXED BRACKET

1112 P07741112 WHEEL SHAFT W/GEAR

1113 P07741113

1114 P07741114

1115 P07741115

1116 P07741116

1117 P07741117

1118 P07741118

1119 P07741119

1120 P07741120

1121 P07741121

1122 P07741122

1123 P07741123

BEARING PLATE (LOWER)

WHEEL 55MM, RUBBER

BALL BEARING 6002-2RS

CAP SCREW M6-1 X 20

CAP SCREW M5-.8 X 12

CAP SCREW M4-.7 X 25

FLAT HD CAP SCR M8-1.25 X 20

SELF-LUBE BEARING DU0810

HEX NUT M6-1

HEX NUT M6-1 LH

HEX NUT M8-1.25

-94BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

1126

1109

1127

1106

1105

1146

1123

1124

1125

1110

1119

1143

1139

1122

1128

1108

1129

1135

1107

1138

1137

1131

1130

1121

1136

REF PART # DESCRIPTION

1124 P07741124 LOCK WASHER 8MM

1125 P07741125 FLAT WASHER 8MM

1126 P07741126 SELF-LUBE BEARING DU1520

1127 P07741127 EXT RETAINING RING 15MM

1128 P07741128 COMPRESSION SPRING 1.6 X 12 X 22

1129 P07741129 HEX NUT M8-1.25

1130 P07741130 CLEVIS ROD END

1131 P07741131 KNOB 4-LOBE M8-1.25

1132 P07741132 BALL BEARING 608ZZ

1133 P07741133 E-CLIP 7MM

1134 P07741134 FLAT WASHER 6MM

1135 P07741135 CONNECTOR PLATE

1136 P07741136 STAND-OFF HEX M6-1 X 52, 60L

1137 P07741137 LOCK WASHER 6MM

1138 P07741138 HEX BOLT M6-1 X 16

1139 P07741139 CAP SCREW M6-1 X 12

1140 P07741140 LOCK WASHER 4MM

1141 P07741141 FLAT WASHER 4MM

1142 P07741142 WHEEL BUSHING

1143 P07741143 FLAT WASHER 10MM

1144 P07741144 LOCK WASHER 5MM

1145 P07741145 FENDER WASHER 8 X 23 X 2MM

1146 P07741146 HEX NUT M8-1.25

Model G0774 (Mfd. Since 10/18)

parts end trimmer carriage

End Trimmer Carriage

1239

1237

1200

1230

1231

1229

1214

1213

1215

1216

1217

1220

1235

1218

1219

1216

1245

1225

1243

1212

1234

1227

1241

1206 1219

1205

1244

1242

1219

1233

1241

1251

1216

1215 1252

1249

1250

1223

REF PART # DESCRIPTION

1200 P07741200 END TRIMMER CARRIAGE ASSEMBLY

1201 P07741201 BASE

1202 P07741202 VERTICAL ROD 18 X 128L

1203 P07741203 BALL BEARING 6002LLU

1204 P07741204 HORIZONTAL ROD 10 X 155L

1205 P07741205 GUIDE PLATE

1206 P07741206 HORIZONTAL ROD 16 X 350L

1207 P07741207 LIFTING BLOCK

1208 P07741208 SELF-LUBE BEARING DU1020

1209 P07741209 VERTICAL ROD 12 X 246.5L

1210 P07741210 VERTICAL PLATE

1211 P07741211 TOP PLATE

1212 P07741212 CYLINDER FIXED BLOCK

1213 P07741213 CAP SCREW M8-1.25 X 80

1214 P07741214 CAP SCREW M6-1 X 70

1215 P07741215 BELLEVILLE WASHER 8 X 15MM

1216 P07741216 HEX NUT M8-1.25

1217 P07741217 LOCK NUT M8-1.25

1218 P07741218 LOCK NUT M6-1

1219 P07741219 SET SCREW M6-1 X 8

1220 P07741220 LINEAR BEARING LME16

1221 P07741221 FLAT WASHER 25 X 35 X 1

1222 P07741222 VERTICAL AIR CYLINDER SMC-25M100

1223 P07741223 HORIZONTAL AIR CYLINDER SMC-16N150

1225 P07741225 CAP SCREW M8-1.25 X 20

Model G0774 (Mfd. Since 10/18)

1217

1202

1211

1232

1247

1238

1227

1226

1203

1240

1207

1234

1221

1228

1234

1209

1241

1233

1210

1241

1234

1204

1246

1208

1222

REF PART # DESCRIPTION

1226 P07741226 SPACER 20 X 30L

1227 P07741227 ABS STRIP 4 X 5L

1228 P07741228 HEX BOLT M4-.7 X 6

1229 P07741229 HEX BOLT M8-1.25 X 25

1230 P07741230 LOCK WASHER 8MM

1231 P07741231 FLAT WASHER 8MM

1232 P07741232 CYCLINDER BLOCK 25 X 19L

1233 P07741233 CAP SCREW M6-1 X 20

1234 P07741234 SET SCREW M6-1 X 6

1235 P07741235 HEX NUT M6-1

1237 P07741237 HEX BOLT M8-1.25 X 80

1238 P07741238 SPACER

1239 P07741239 FLAT WASHER 8MM

1240 P07741240 FLAT WASHER 6MM

1241 P07741241 LOCK WASHER 6MM

1242 P07741242 CAP SCREW M6-1 X 16

1243 P07741243 FLAT WASHER 5MM

1244 P07741244 HEX BOLT M5-.8 X 10

1245 P07741245 BUFFER BLOCK

1246 P07741246 LOCK WASHER 10MM

1247 P07741247 BUTTON HD CAP SCR M8-1.25 X 30

1249 P07741249 CONNECTING ROD

1250 P07741250 CYCLINDER PLATE

1251 P07741251 FLAT WASHER 6MM

1252 P07741252 FLAT WASHER 8MM

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-95-

parts end trimmer motor

End Trimmer Motor

1324

1334

1333

1301-1

1301-5

1301-2 1301-4

1301-9

1330

1343

1321

1337

1302

1336

1323

1329

1335

1332

1342

1312

1301

1328

1322

1313

1316

1315

1314

1311

1310

1326

1340

1334 1309

1317

1325

1344

1319

1306

1307

1341

1327

1318

1320

1308

1305

1338

1304

1309

1303

1331

1306

1332

REF PART # DESCRIPTION

1304

1305

1306

1307

1308

1309

1310

1311

1312

1313

1314

1301 P07741301 MOTOR 1/4HP 220V 1-PH (END TRIMMER)

1301-1 P07741301-1 MOTOR FAN COVER

1301-2 P07741301-2 MOTOR FAN

1301-4 P07741301-4 R CAPACITOR 5M 500V

1301-5 P07741301-5 MOTOR JUNCTION BOX

1301-8 P07741301-8 BALL BEARING 6202ZZ (FRONT)

1301-9 P07741301-9 BALL BEARING 6200ZZ (REAR)

1302

1303

P07741302

P07741303

MOTOR MOUNT BRACKET

BOARD SUPPORT BRACKET

1315

1316

1317

1318

1319

P07741304

P07741305

P07741306

P07741307

P07741308

P07741309

P07741310

P07741311

P07741312

P07741313

P07741314

P07741315

P07741316

P07741317

P07741318

P07741319

BRACKET PLATE

BALL BEARING 692ZZ

FLAT HD CAP SCR M5-.8 X 16

SET SCREW M3-.5 X 3

ROLL PIN 1 X 20

FLAT WASHER 5 X 12 X .6

BALL BEARING 6202LLB

BEARING SPACER

INT RETAINING RING 35MM

SPROCKET SPINDLE

BEARING SPACER

SPROCKET WASHER 8MM

CAP SCREW M8-1.25 X 20

BLADE FLANGE

BLADE 16T 6MM BORE

BLADE SPACER

REF PART #

1320 P07741320

1321 P07741321

1322 P07741322

1323 P07741323

1324 P07741324

1325 P07741325

1326 P07741326

1327 P07741327

1328 P07741328

1329 P07741329

1330 P07741330

1331 P07741331

1332 P07741332

1333 P07741333

1334 P07741334

1335 P07741335

1336 P07741336

1337 P07741337

1338 P07741338

1340 P07741340

1341 P07741341

1342 P07741342

1343 P07741343

1344 P07741344

DESCRIPTION

FLANGE

SPROCKET 48T

SPACER BLOCK

BELT TENSION PLATE

BELT COVER

DUST COVER

BRUSH

HEX BOLT M6-1 X 16

LINEAR BEARING LM12UU

TIMING BELT 10T5-500

BALL BEARING 6904LLB

CAP SCREW M6-1 X 20

LOCK WASHER 6MM

CAP SCREW M5-.8 X 12

FLAT WASHER 5MM

CAP SCREW M6-1 X 40

FLAT WASHER 6MM

CAP SCREW M5-.8 X 16

END TRIMMER TRACER

FLANGE BOLT M5-.8 X 16

MOTOR CORD 16G 3W 36"

WASHER 15.2 X 22 X .2MM

FLAT WASHER 5MM

SET SCREW M5-.8 X 5

-96BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0774 (Mfd. Since 10/18)

parts vertical edgebanding guide

Vertical Edgebanding Guide & Glue Spindle

1400

1500

1417

1409

1418

1406

1415

1422

1419 1410

1412

1413

1405

1413

1404

1402

1403

1416

1401

1414

1407

1420

1409

1420

1421

1423

1408

1502

1507

1503

REF PART # DESCRIPTION

1400 P07741400 VERTICAL EDGEBANDING GUIDE ASSY

1401 P07741401 EDGEBAND SEAT (LOWER)

1402 P07741402 EDGEBAND SEAT (UPPER)

1403 P07741403 VERTICAL ROD 10 X 90L

1404 P07741404 SET SCREW M10-1.5 X 190

1405 P07741405 KNOB 4-LOBE M10-1.5

1406 P07741406 PROTECTION PLATE

1407 P07741407 SPRING PLATE

1408 P07741408 HEX BOLT M5-.8 X 10

1409 P07741409 LOCK WASHER 5MM

1410 P07741410 BUTTON HD CAP SCR M4-.7 X 10

1412 P07741412 SET SCREW M6-1 X 6

1413 P07741413 HEX NUT M10-1.5

1414 P07741414 FLAT WASHER 6 X 15 X .5MM

1415 P07741415 FENDER WASHER 6MM

1416 P07741416 CAP SCREW M6-1 X 20

1417 P07741417 BUTTON HD CAP SCR M5-.8 X 10

1418 P07741418 ABS STRIP 4 X 5L

1419 P07741419 SET SCREW M5-.8 X 8

1420 P07741420 FLAT WASHER 4MM

1421 P07741421 LOCK WASHER 4MM

1508

1504

1513

1512

1501

1510

1511

1509

1506

1514

1518

1504

1516

1515

1505

1517

REF PART # DESCRIPTION

1422 P07741422 FLAT WASHER 6MM

1423 P07741423 LOCK WASHER 6MM

1500 P07741500 GLUE SPINDLE ASSEMBLY

1501 P07741501 GLUE SPINDLE BASE

1502 P07741502 GLUE SPINDLE

1503 P07741503 SPACER

1504 P07741504 FLAT WASHER 25 X 35 X 1MM

1505 P07741505 SPANNER NUT W/ BEARING LOCK WASHER

1506 P07741506 BALL BEARING 6005ZZ

1507 P07741507 BUSHING

1508 P07741508 COLLAR

1509 P07741509 INT RETAINING RING 47MM

1510 P07741510 BALL BEARING 6005ZZ

1511 P07741511 BUSHING

1512 P07741512 CAP SCREW M6-1 X 25

1513 P07741513 LOCK WASHER 5MM

1514 P07741514 SET SCREW M5-.8 X 6

1515 P07741515 INTERNAL GASKET

1516 P07741516 EXTERNAL GASKET

1517 P07741517 GEAR 21T

1518 P07741518 SET SCREW M6-1 X 8

Model G0774 (Mfd. Since 10/18) BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-97-

parts glue pot cover

Glue Pot Cover

1630

1628

1629

1611

1637

1609

1628

1635

1638

1639

1623

1634

1623

1636

1601

1625

1602

1628

1610

1625

1632

1631

1614

1627

1622

1621

1622

1616

1636

1642

1618

1619

1627

1640

1624

1617

1643

1644

1604

1615

1622

1626

1645

1612

1641

1622

1603

1613

1600

1633

1622

1608

1623

1624

1605 1606

1620

1607

REF PART # DESCRIPTION

1600 P07741600 GLUE POT COVER ASSEMBLY

1601 P07741601 ADJUSTMENT BLOCK SPACER

1602 P07741602 SPACER

1603 P07741603 LOCATE BLOCK

1604 P07741604 FRONT COVER PLATE

1605 P07741605 BASE

1606 P07741606 SIDE COVER PLATE

1607 P07741607 BOTTOM COVER PLATE

1608 P07741608 GUIDE BRACKET

1609 P07741609 BLOCK PIN

1610 P07741610 ADJUSTMENT BLOCK

1611 P07741611 SUPPORT PLATE

1612 P07741612

1613 P07741613

1614 P07741614

1615 P07741615

1616 P07741616

1617 P07741617

1618 P07741618

1619 P07741619

1620 P07741620

1621 P07741621

1622 P07741622

GLUE POT HEATING ELEMENT

ROTATION SHAFT

BRACKET

GLUE POT COVER (UPPER)

KNOB 4-LOBE M8-1.25

CAP SCREW M8-1.25 X 55

HEX NUT M8-1.25

GLUE POT LID

CAP SCREW M4-.7 X 6

CAP SCREW M6-1 X 16

LOCK WASHER 6MM

-98BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

REF PART # DESCRIPTION

1623 P07741623 FENDER WASHER 6 X 19 X 2

1624 P07741624 BUTTON HD CAP SCR M4-.7 X 6

1625 P07741625 WAVY WASHER 15 X 22MM

1626 P07741626 CAP SCREW M6-1 X 12

1627 P07741627 FLAT WASHER 6MM

1628 P07741628 HEX NUT M6-1

1629 P07741629 BELLEVILLE LOCK WASHER 6MM

1630 P07741630 KNOB BOLT 4-LOBE M6-1 X 75

1631 P07741631 HEAT ROD MOUNTING PLATE

1632 P07741632 FLANGE BOLT M6-1 X 8

1633 P07741633 HEX BOLT M6-1 X 16

1634 P07741634 SET SCREW M6-1 X 8

1635 P07741635 HEX BOLT M8-1.25 X 30

1636 P07741636 LOCK WASHER 8MM

1637 P07741637 CAP SCREW M5-.8 X 16

1638 P07741638 LOCK WASHER 5MM

1639 P07741639 FLAT WASHER 5MM

1640 P07741640 FLANGE NUT M6-1

1641 P07741641 CAP SCREW M6-1 X 20

1642 P07741642 CAP SCREW M6-1 X 20

1643 P07741643 LOCK WASHER 6MM

1644 P07741644 FLAT WASHER 6MM

1645 P07741645 HEAT ELEMENT BRACKET

Model G0774 (Mfd. Since 10/18)

parts glue pot

Glue Pot

1721

1717

1723

1722

1701

1704

1720

1717

1716

1714

1715

1725

1708

1718

1705

1706

1719

1709

1728

1726

1710

1702

1724

1718

1707

1720

1717

1711 1703

1712

1713

1727

1700

REF PART # DESCRIPTION

1700 P07741700 GLUE POT ASSEMBLY

1701 P07741701 GLUE POT

1702 P07741702 ELECTRIC ELEMENT

1703 P07741703 TUBING BRACKET

1704 P07741704 GLUE POT GASKET

1705 P07741705 HEATING ELEMENT 220V 160W

1706 P07741706 HEATING ELEMENT 220V 250W

1707 P07741707 BRASS TUBING 300 X 4MM

1708 P07741708 STRAIN RELIEF TYPE-1 PG11

1709 P07741709 JUNCTION BOX

1710 P07741710 CONNECTOR 1/4" ID BRASS FEMALE

1711 P07741711 CONNECTOR 1/4" ID BRASS MALE

1712 P07741712 GREASE ADAPTER

1713 P07741713 GREASE FITTING M6-1.0 STRAIGHT

1714 P07741714 THERMOCOUPLE W/ WIRES

REF PART # DESCRIPTION

1715 P07741715 CERAMIC TERMINAL BLOCK

1716 P07741716 CAP SCREW M6-1 X 50

1717 P07741717 LOCK WASHER 6MM

1718 P07741718 SET SCREW M6-1 X 6

1719 P07741719 CAP SCREW M5-.8 X 12

1720 P07741720 BELLEVILLE LOCK WASHER 6MM

1721 P07741721 CAP SCREW M6-1 X 20

1722 P07741722 FLAT WASHER 6MM

1723 P07741723 FLAT HD CAP SCR M6-1 X 20

1724 P07741724 CAP SCREW M6-1 X 25

1725 P07741725 HEX NUT 1/4-20

1726 P07741726 CORD 14G 2W 16"

1727 P07741727 CAP SCREW M6-1 X 12

1728 P07741728 BUTTON HD CAP SCR M4-.7 X 8

Model G0774 (Mfd. Since 10/18) BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-99-

parts glue spindle motor

1826

1838

1831

1832

1800

Glue Spindle Motor

1841

1828

1834

1813 1825

1813

1801

1833

1803

1812

1823

18311832

1811

1824

1813

1804

1814

1805

1806

1810

1815

1808

1806

1807

1838 1830

1829

1837

1819

1809

1820

1827

1835

1802

1839

1828

1836

1821

1816

1818

1817

1822

1822-1 1822-5 1822-6

1840

1822-2

1822-4

1822-7

1822-10

1822-8 1822-9

REF PART # DESCRIPTION

1800 P07741800 GLUE SPINDLE MOTOR ASSEMBLY

1801 P07741801 REDUCER CONNECTION PLATE

1802 P07741802 SPINDLE BRACKET

1803 P07741803 REDUCER BRACKET

1804 P07741804 COMPRESSION SPRING 1.7 X 18 X 45

1805 P07741805 GASKET

1806 P07741806 BALL BEARING 6005ZZ

1807 P07741807 BEARING RING

1808 P07741808 EXT RETAINING RING 25MM

1809 P07741809 GEAR 21T

1810 P07741810 KNOB M8-1.25, 30MM OD

1811 P07741811 STUD-FT M8-1.25 X 180

1812 P07741812 CLEVIS ROD-END

1813 P07741813 HEX NUT M8-1.25

1814 P07741814 FENDER WASHER 8 X 23 X 2MM

1815 P07741815 LOCK NUT M8-1.25

1816 P07741816 KEYED SHAFT

1817 P07741817 EXT RETAINING RING 14MM

1818 P07741818 KEY 5 X 5 X 15

1819 P07741819 GEAR CONNECTION SHAFT

1820 P07741820 SET SCREW M6-1 X 8

1821 P07741821 GEAR REDUCER

1822 P07741822 MOTOR 1/3HP 220V 1-PH (GLUE SPINDLE)

1822-1 P07741822-1 MOTOR FAN COVER

1822-2 P07741822-2 MOTOR FAN

1822-4 P07741822-4 R CAPACITOR 20MFD 250V

-100BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

REF PART # DESCRIPTION

1826

1827

1828

1829

1830

1831

1832

1833

1834

1835

1836

1837

1838

1839

1840

1841

1822-5 P07741822-5 MOTOR JUNCTION BOX

1822-6 P07741822-6 CONTACT PLATE

1822-7 P07741822-7 CENTRIFUGAL SWITCH

1822-8 P07741822-8 BALL BEARING 6203ZZ (FRONT)

1822-9 P07741822-9 BALL BEARING 6202ZZ (REAR)

1822-10 P07741822-10 S CAPACITOR 100MFD 250V

1823

1824

1825

P07741823

P07741824

P07741825

CLEVIS ROD-END

BUSHING

SET SCREW M8-1.25 X 65

P07741826

P07741827

P07741828

P07741829

P07741830

P07741831

P07741832

P07741833

P07741834

P07741835

P07741836

P07741837

P07741838

P07741839

P07741840

P07741841

CAP SCREW M8-1.25 X 20

FLAT WASHER 8MM

LOCK WASHER 8MM

CAP SCREW M6-1 X 90

FLAT WASHER 6MM

LOCK WASHER 6MM

HEX NUT M6-1

CAP SCREW M8-1.25 X 90

FLAT WASHER 8MM

HEX BOLT M8-1.25 X 30

HEX BOLT M5-.8 X 12

HEX BOLT M6-1 X 20

FLAT WASHER 6MM

SET SCREW M8-1.25 X 16

MOTOR CORD 16G 3W 18"

BUTTON HD CAP SCR M6-1 X 8

Model G0774 (Mfd. Since 10/18)

parts upper lower buffing motors

Upper & Lower Buffing Motors

1901-1

1901-2

1901-4 1901-8 1901-9

2000

1901-5

1901

1919

1906

1900

1908

1912

1907

1902

1905

1904

1915

1903

1910

1909

1912

1918

1917

2007

2005

2018

2020

2001

2001-1 2001-2

2006

2002

2001-5

2004

2016

2015

2003

2009

2001-4 2001-8 2001-9

2011

2012

REF PART # DESCRIPTION

1900 P07741900 UPPER BUFFING MOTOR ASSEMBLY

1901 P07741901 MOTOR 1/4HP 220V 1-PH (UPPER BUFF)

1901-1 P07741901-1 MOTOR FAN COVER

1901-2 P07741901-2 MOTOR FAN

1901-4 P07741901-4 R CAPACITOR 5M 500V 1-1/2" X 2"

1901-5 P07741901-5 MOTOR JUNCTION BOX

1901-8 P07741901-8 BALL BEARING 6202ZZ (FRONT)

1901-9 P07741901-9 BALL BEARING 6200ZZ (REAR)

1902 P07741902 MOTOR MOUNTING PLATE

1903 P07741903 BUFFING WHEEL 5 X 1/2 X 3/4

1904 P07741904 CAP SCREW M5-.8 X 16

1905 P07741905 LOCK WASHER 5MM

1906 P07741906 BOLT PLATE

1907 P07741907 HEX BOLT M8-1.25 X 25

1908 P07741908 FLAT WASHER 8MM

1909 P07741909 WHEEL FLANGE

1910 P07741910 SPINDLE (UPPER)

1912 P07741912 LOCK WASHER 8MM

1915 P07741915 CAP SCREW M6-1 X 12

1917 P07741917 HEX BOLT M8-1.25 X 20 LH

1918 P07741918 FLAT WASHER 22 X 55 X 3MM

1919 P07741919 MOTOR CORD 16G 3W 36"

REF PART # DESCRIPTION

2000 P07742000 LOWER BUFFING MOTOR ASSEMBLY

2001 P07742001 MOTOR 1/4HP 220V 1-PH (LOWER BUFF)

2001-1 P07742001-1 MOTOR FAN COVER

2001-2 P07742001-2 MOTOR FAN

2001-4 P07742001-4 R CAPACITOR 5M 500V 1-1/2" X 2"

2001-5 P07742001-5 MOTOR JUNCTION BOX

2001-8 P07742001-8 BALL BEARING 6202ZZ (FRONT)

2001-9 P07742001-9 BALL BEARING 6200ZZ (REAR)

2002 P07742002 MOTOR MOUNTING PLATE

2003 P07742003 BUFFING WHEEL 5 X 1/2 X 3/4

2004 P07742004 CAP SCREW M5-.8 X 16

2005 P07742005 LOCK WASHER 5MM

2006 P07742006 BOLT PLATE

2007 P07742007 HEX BOLT M8-1.25 X 25

2008 P07742008 FLAT WASHER 8MM

2009 P07742009 WHEEL FLANGE

2011 P07742011 HEX BOLT M8-1.25 X 20

2012 P07742012 LOCK WASHER 8MM

2015 P07742015 CAP SCREW M6-1 X 12

2016 P07742016 SPINDLE (LOWER)

2018 P07742018 FLAT WASHER 22 X 55 X 3MM

2020 P07742020 MOTOR CORD 16G 3W 24"

Model G0774 (Mfd. Since 10/18) BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-101-

parts upper flush trimmer

2100

Upper Flush Trimmer

2151

2155

2126 2123

2122

2120

2114

2128

2129

2127

2125

2124

2121

2152

2117

2116

2119

2118

2138

2140

2135 2136

2139

2137

2138

2115

2148

2147

2130

2114

2154

2110

2109

2110

2103

2145

2108

2146

2107

2153

2149

2105

2150

2106

2148

2101

2143

2154

2115

2111

2112

2104

2156

2113

2142

2102

2131

2144-1

2144

2144-3

2153

2134

2133

2132

2144-4

2144-2

REF PART # DESCRIPTION

2100 P07742100 UPPER FLUSH TRIMMER ASSEMBLY

2101 P07742101 LINEAR BEARING LM12

2102 P07742102 BALL BEARING 6002LLB

2103 P07742103 STAND-OFF HEX 61.5MM

2104 P07742104 SPINDLE SPACER

2105 P07742105 MOUNTING PLATE

2106 P07742106 WAVY WASHER 8MM

2107 P07742107 ADAPTER SHAFT M8-1.25

2108 P07742108 KNOB 4-LOBE M8-1.25

2109 P07742109 STUD-FT M8-1.25 X 125

2110 P07742110 HEX NUT M8-1.25

2111 P07742111 CONNECTION PLATE

2112 P07742112 FLAT HD CAP SCR M4-.7 X 8

2113 P07742113 FLAT PULLEY

2114 P07742114 THREADED ROD M12-1.75 X 104

2115 P07742115 HEX NUT M12-1.75

2116 P07742116 BALL BEARING 6000LLB

2117 P07742117 PROFILING WHEEL

2118 P07742118 WHEEL SPINDLE

2119 P07742119 EXT RETAINING RING 10MM

2120 P07742120 WHEEL MOUNTING PLATE (OUTER)

2121 P07742121 WHEEL MOUNTING PLATE (INNER)

2122 P07742122 BUTTON HD CAP SCR M5-.8 X 8

2123 P07742123 FLAT HD CAP SCR M5-.8 X 8

2124 P07742124 CAP SCREW M5-.8 X 10

2125 P07742125 CAP SCREW M5-.8 X 30

2126 P07742126 LOCK NUT M5-.8

2127 P07742127 BELLEVILLE LOCK WASHER 5MM

2128 P07742128 HEX NUT M5-.8

2129 P07742129 SPRING PLATE

2130 P07742130 MOUNTING BLOCK

REF PART # DESCRIPTION

2131 P07742131 BEARING COLLAR (UPPER)

2132 P07742132 ADJUSTMENT BRACKET

2133 P07742133 FENDER WASHER 6MM

2134 P07742134 CAP SCREW M6-1 X 12

2135 P07742135 DUST COVER

2136 P07742136 STUD-DE M6-1

2137 P07742137 COMPRESSION SPRING 1 X 12 X 46

2138 P07742138 FENDER WASHER 6MM

2139 P07742139 FENDER WASHER 6MM

2140 P07742140 COMPRESSION SPRING 1.5 X 17 X 22

2141 P07742141 LOCK NUT M6-1

2142 P07742142 FLUSH TRIMMER SPINDLE (UPPER)

2143 P07742143 CAP SCREW M5-.8 X 20

2144 P07742144 FLUSH TRIMMER ASSEMBLY (UPPER)

2144-1 P07742144-1 FLUSH TRIMMER CUTTERHEAD (UPPER)

2144-2 P07742144-2 CUTTERHEAD BLOCK (UPPER)

2144-3 P07742144-3 CUTTERHEAD KNIFE (UPPER)

2144-4 P07742144-4 SET SCREW M6-1 X 16 DOG-PT

2145 P07742145 SPANNER NUT M10-.75

2146 P07742146 POSITION COUNTER

2147 P07742147 ABS STRIPS 4 X 5L

2148 P07742148 SET SCREW M6-1 X 6

2149 P07742149 CAP SCREW M6-1 X 16

2150 P07742150 FENDER WASHER 6MM

2151 P07742151 DUST COVER BRUSH

2152 P07742152 LOCK WASHER 5MM

2153 P07742153 LOCK WASHER 6MM

2154 P07742154 HEX NUT M6-1

2155 P07742155 FLAT HD CAP SCR M4-.7 X 8

2156 P07742156 SET SCREW M5-.8 X 8

-102BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0774 (Mfd. Since 10/18)

parts lower flush trimmer

Lower Flush Trimmer

2223

2231

2225

2235-2

2235-1

2235-3

2220

2222

2232

2224

2219

2230

2228

2227

2247

2238

2226

2229

2221

2201

2202

2218

2235-4

2207

2235

2234

2233

2245

2249

2217

2242

2244

2241

2243

2213

2212

2211

2209

2210

2237

2236

2213

2209

2208

2206

2215

2248

2240

2241

2239

2243

2205

2204

2203

2214

2204

2200

2216

REF PART #

2200 P07742200

2201 P07742201

2202 P07742202

2203 P07742203

2204 P07742204

2205 P07742205

2206 P07742206

2207 P07742207

2208 P07742208

2209 P07742209

2210 P07742210

2211 P07742211

2212 P07742212

2213 P07742213

2214 P07742214

2215 P07742215

2216 P07742216

2217 P07742217

2218 P07742218

2219 P07742219

2220 P07742220

2221 P07742221

2222 P07742222

2223 P07742223

2224 P07742224

2225 P07742225

2226 P07742226

DESCRIPTION

LOWER FLUSH TRIMMER ASSEMBLY

LOWER MOUNTING BLOCK

LINEAR BEARING LM12

BEARING COLLAR (LOWER)

BALL BEARING 6002LLB

FLUSH TRIMMER SPINDLE (LOWER)

STAND-OFF HEX 61.5MM

SPINDLE SPACER

MOUNTING PLATE

WAVY WASHER 8MM

ADAPTER SHAFT

KNOB 4-LOBE M8-1.25

STUD-FT M8-1.25 X 125

HEX NUT M8-1.25

CONNECTION PLATE

FLAT HD CAP SCR M4-.7 X 8

FLAT PULLEY

THREADED ROD M12-1.75 X 104

HEX NUT M12-1.75

BALL BEARING 6000LLB

PROFILING WHEEL

WHEEL SPINDLE

EXT RETAINING RING 10MM

WHEEL MOUNTING PLATE (OUTER)

WHEEL MOUNTING PLATE (INNER)

BUTTON HD CAP SCR M5-.8 X 8

FLAT HD CAP SCR M5-.8 X 8

REF PART # DESCRIPTION

2239

2240

2241

2242

2243

2244

2245

2247

2248

2249

2227

2228

2229

2230

2231

2232

2233

2234

P07742227

P07742228

P07742229

P07742230

P07742231

P07742232

P07742233

P07742234

CAP SCREW M5-.8 X 10

CAP SCREW M5-.8 X 30

LOCK NUT M5-.8

BELLEVILLE LOCK WASHER 5.2 X 12 X .6MM

HEX NUT M5-.8

SPRING PLATE

DUST COVER

CAP SCREW M5-.8 X 16 LH

2235 P07742235 FLUSH TRIMMER ASSEMBLY (LOWER)

2235-1 P07742235-1 FLUSH TRIMMER CUTTERHEAD (LOWER)

2235-2 P07742235-2 CUTTERHEAD BLOCK (LOWER)

2235-3 P07742235-3 CUTTERHEAD KNIFE (LOWER)

2235-4 P07742235-4 SET SCREW M6-1 X 16 DOG-PT

2236 P07742236 SPANNER NUT M10-.75

2237

2238

P07742237

P07742238

POSITION COUNTER

LOCK WASHER 5MM

P07742239

P07742240

P07742241

P07742242

P07742243

P07742244

P07742245

P07742247

P07742248

P07742249

CAP SCREW M6-1 X 16

FENDER WASHER 6MM

SET SCREW M6-1 X 6

CAP SCREW M6-1 X 20

LOCK WASHER 6MM

ABS STRIP

DUST COVER BRUSH

FLAT HD CAP SCR M4-.7 X 8

SET SCREW M5-.8 X 8

FLANGE BOLT M6-1 X 12

Model G0774 (Mfd. Since 10/18) BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-103-

parts electrical panel

Electrical Panel

2323

2301

2302

2301 2302

2301

2302

2301

2316 2315 2316 2301

2302

2301

2302

2301

2309

2324

2301

2303

2325

2314

2305 2305

2319

2314

2310

2307 2322

QM1 QM2 QM3 QM4 QM5

2317

2320

2326

KM1 KM2 KM3 KM4 KM5 KM6 KM7

2306

2316

2315 2312

2311

2304

2321 2318

REF PART # DESCRIPTION

2301 P07742301 TERMINAL BAR PYK2 1-PC

2302 P07742302 TERMINAL BAR PYK2, GROUND 1-PC

2303 P07742303 TERMINAL END PLATE

2304 P07742304 MOUNTING RAIL END PLATE

2305 P07742305 TERMINAL JUMPER

2306 P07742306 TRANSFORMER 220V LCE LCP-TBSM-100120

2307 P07742307 INVERTER DELTA DVP32ES200R

2308 P07742308 CONTACTOR SHIHLIN S-P11S 24V

2309 P07742309 FLANGE SCR M5-.8 X 10

2310 P07742310 FLANGE SCR M5-.8 X 10

2311 P07742311 OL RELAY SHIHLIN MR-32S-2.5 1.6-2.5A

2312 P07742312 OL RELAY SHIHLIN MR-32S-4 2.5-4A

2313 P07742313 OL RELAY SHIHLIN MR-32S-6.3 4-6.3A

2313

2312

2308

REF PART # DESCRIPTION

2314 P07742314 FUSE HOLDER PMX-10 X 38 RM32 32A 680V

2315 P07742315 FUSE 10 X 38MM 6A 600V F-A, CERAMIC

2316 P07742316 FUSE 10 X 38MM 3A 600V F-A, CERAMIC

2317 P07742317 GROUND TERMINAL 6-POLE 20A

2318 P07742318 CONTROL PANEL MOUNT

2319 P07742319 RELAY OMRON MY4N-J 24V

2320 P07742320 WIRING LOOM 1 X 2-1/2 X 34"

2321 P07742321 WIRING LOOM 1 X 2-1/2 X 7"

2322 P07742322 WIRING LOOM 1 X 2-1/2 X 5"

2323 P07742323 MOUNTING RAIL 1-3/8 X 1-3/8 X 17"

2324 P07742324 MOUNTING RAIL 1-3/8 X 1-3/8 X 6-1/4"

2325 P07742325 MOUNTING RAIL 1-3/8 X 1-3/8 X 17-1/4"

2326 P07742326 MOUNTING RAIL 1-3/8 X 1-3/8 X 12-1/4"

-104BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0774 (Mfd. Since 10/18)

Loosen conveyor housing lock handle before adjusting conveyor elevation.

2401

Labels & Cosmetics (Front)

2403

2415

2402

2404

For best results and machine performance,

DO NOT insert workpieces into panel feeder until all components are fully powered-up and reach specified operating temperature.

2416

2404

2406

2405

Set air pressure at 100 PSI for optimal performance.

2407

2414

MODEL G0774

AUTOMATIC EDGEBANDER

Specifications

Power Requirement: 220V, 1-Ph, 60 Hz

Full-Load Amp Draw: 19A

Feed Motor: 3/4 HP

Glue & Edge Motor: 1/3 HP

End Trim Motor: 1/4 HP

Flush Trim Motor: 3/4 HP

Buffing Motor: 1/4 HP

Min. Panel Dimensions: 4-3/4"–9-1/2"

Panel Thickness (Min.-Max.): 1/2"–1-3/4"

Tape Thickness (Min.-Max.): 0.5–3mm

Required Air Supply: 100 PSI

Panel Feed Speed: 16 FPM

Glue Pot Capacity: 34 oz.

Weight: 754 lbs.

Date

S/N

Manufactured for Grizzly in Taiwan

To reduce the risk of serious personal injury while using this machine:

1. Read and understand owner’s manual before starting.

2. Always wear approved safety glasses, respirator, and hearing protection.

3. Only plug power cord into a grounded outlet.

4. Disconnect power and allow hot parts to cool before adjusting or servicing.

5. Make sure machine is properly set up and adjusted before starting.

6. Avoid getting entangled or caught in moving parts—tie back long hair, roll up sleeves, and DO NOT wear loose clothing, gloves, or jewelry.

7. Never reach inside machine during operation.

8. Always keep hands/fingers away from glue pot and any hot, sharp, or moving parts.

9. DO NOT allow hands or clothing to get pulled into conveyor while feeding workpiece.

10. Keep all guards and covers in place during operation.

11. Never leave machine running while unattended.

12. Only operate in a well-ventilated area. DO NOT operate near flammables.

13. DO NOT modify machine in any way or operate with broken or damaged parts.

14. DO NOT operate when tired or under influence of drugs or alcohol.

15. DO NOT expose to rain or use in wet locations.

16. Prevent unauthorized use by children or untrained users; restrict access or disable machine when unattended.

To reduce risk of death or serious injury, read manual BEFORE using machine.

To get a new manual, call

(800) 523-4777 or go to

www.grizzly.com.

2413

EYE/LUNG INJURY

HAZARD!

glasses and a respirator when using this machine.

2409

2408

WARNING!

ENTANGLEMENT

HAZARD!

Tie back long hair, roll up long sleeves, and remove loose clothing, jewelry, or gloves to prevent getting caught in moving parts.

INJURY/SHOCK

HAZARD!

Disconnect power before adjustments, maintenance, or service.

2412

2411 G0774

2410

grizzly.com

REF PART # DESCRIPTION

2401 P07742401 NOTICE UNLOCK CONVEYOR LABEL

2402 P07742402 TOUCH-UP PAINT, GRIZZLY GREEN

2403 P07742403 GRIZZLY NAMEPLATE (LARGE)

2404 P07742404 WARNING HOT SURFACE LABEL

2405 P07742405 NOTICE AIR PRESSURE LABEL

2406 P07742406 TOUCH-UP PAINT, GRIZZLY GREY PUTTY

2407 P07742407 ELECTRICITY LABEL

2408 P07742408 GLASSES/RESPIRATOR LABEL

REF PART # DESCRIPTION

2409 P07742409 ENTANGLEMENT LABEL

2410 P07742410 GRIZZLY.COM LABEL

2411 P07742411 MODEL NUMBER LABEL

2412 P07742412 DISCONNECT POWER LABEL

2413 P07742413 READ MANUAL LABEL

2414 P07742414 MACHINE ID LABEL

2415 P07742415 CONVEYOR BELT TENSION LABEL

2416 P07742416 NOTICE COMPONENTS POWERED UP

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

Model G0774 (Mfd. Since 10/18) BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-105-

Labels & Cosmetics (Rear)

2502

2501

2503

2502

2507

Lubricate every

30 hours with

NLGI #2 grease or equivalent.

2502

REF PART #

2501 P07742501

2502 P07742502

2503 P07742503

DESCRIPTION

WARNING HOT SURFACE LABEL

ELECTRICITY LABEL

COUNTER ROTATION LABEL

2506

INJURY/SHOCK

HAZARD!

Disconnect power before adjustments, maintenance, or service.

2505

REF PART #

2505 P07742505

2506 P07742506

2507 P07742507

DESCRIPTION

DISCONNECT POWER LABEL

VALVE ADJUSTMENT LABEL

LUBRICATION NOTICE LABEL

-106BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0774 (Mfd. Since 10/18)

WARRANTY CARD

Name _____________________________________________________________________________

Street _____________________________________________________________________________

City _______________________ State _________________________ Zip _____________________

Phone # ____________________ Email _________________________________________________

Model # ____________________ Order # _______________________ Serial # __________________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is strictly confidential.

How did you learn about us?

____ Advertisement

____ Card Deck

____ Friend

____ Website

____ Catalog

____ Other:

Which of the following magazines do you subscribe to?

____ Cabinetmaker & FDM

____ Family Handyman

____ Hand Loader

____ Handy

____ Home Shop Machinist

____ Journal of Light Cont.

____ Live Steam

____ Model Airplane News

____ Old House Journal

____ Popular Mechanics

____ Popular Science

____ Popular Woodworking

____ Precision Shooter

____ Projects in Metal

____ RC Modeler

____ Rifle

____ Shop Notes

____ Shotgun News

____ Today’s Homeowner

____ Wood

What is your annual household income?

____ $20,000-$29,000

____ $50,000-$59,000

____ $30,000-$39,000

____ $60,000-$69,000

____ Wooden Boat

____ Woodshop News

____ Woodsmith

____ Woodwork

____ Woodworker West

____ Woodworker’s Journal

____ Other:

____ $40,000-$49,000

____ $70,000+

What is your age group?

____ 20-29

____ 50-59

____ 30-39

____ 60-69

____ 40-49

____ 70+

How long have you been a woodworker/metalworker?

____ 0-2 Years ____ 2-8 Years ____ 8-20 Years

How many of your machines or tools are Grizzly?

____ 0-2 ____ 3-5 ____ 6-9

____ 20+ Years

____ 10+

Do you think your machine represents a good value? _____Yes

Would you recommend Grizzly Industrial to a friend? _____Yes

_____No

Would you allow us to use your name as a reference for Grizzly customers in your area?

Note: We never use names more than 3 times. _____Yes _____No

10.

Comments: _____________________________________________________________________

_________________________________________________________________________________

FOLD ALONG DOTTED LINE

GRIZZLY INDUSTRIAL, INC.

P.O. BOX 2069

BELLINGHAM, WA 98227-2069

FOLD ALONG DOTTED LINE

Send a Grizzly Catalog to a friend:

Name_______________________________

Street_______________________________

City______________State______Zip______

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

Place

Stamp

Here

WARRANTY & RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.

In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We will not accept any item back without this number. Proof of purchase must accompany the merchandise.

The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our products meet high quality and durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

Key Features

Precision construction for accurate edgebanding
Automatic glue application for consistent results
Built-in end trimmer for clean and precise trimming
Variable speed control to match the material being edged
Easy-to-use control panel for simple operation
Compact size for easy installation in small workshops

Frequently Answers and Questions

What materials can I edgeband with the Grizzly Industrial G0774?

The G0774 can edgeband a variety of materials, including wood, particle board, MDF, and plywood.

What thickness of panels can I edgeband with the G0774?

The G0774 can edgeband panels with a thickness of 1/4" to 1".

How do I adjust the glue application rate?

The glue application rate can be adjusted by turning the glue flow knob on the control panel.

How do I change the edgebanding material?

To change the edgebanding material, simply remove the old coil and install the new coil on the spindle.

MODEL G0774

AUTOMATIC EDGEBANDER

OWNER'S MANUAL

(For models manufactured since 10/18)

This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.

The manufacturer will not be held liable for injury or property damage from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals:

Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Table of Contents

INTRODUCTION

Contact Info

Manual Accuracy

Identification (Front)

Identification (Rear)

Controls &

Components

Control Panel

Coil Support

Guillotine

Glue System

Pressure Rollers End Trimmer

Flush Trimmer

Buffing Unit

Panel Feeder

Edgebanding Feeder

Infeed Fence

Power & Air

Machine Data Sheet

MODEL G0774

AUTOMATIC EDGEBANDER

SECTION 1: SAFETY

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

Safety Instructions for Machinery

Additional Safety for Automatic Edgebanders

SECTION 2: POWER SUPPLY

Availability

Circuit Information

Full-Load Current Rating

Circuit Requirements

Grounding Requirements

Extension Cords

SECTION 3: SETUP

Needed for Setup

Unpacking

Inventory

5mm

Hardware Recognition Chart

USE THIS CHART TO MATCH UP

HARDWARE DURING THE INVENTORY

AND ASSEMBLY PROCESS.

5

Site Considerations

Weight Load

Space Allocation

Physical Environment

Electrical Installation

Lighting

Lifting & Placing

Assembly

Cleanup

Dust Collection

Test Run

SECTION 4: OPERATIONS

Operation Overview

Checking/Adding

Glue

Setting Panel Feeder

Height

Setting Infeed Fence

Position

Using Infeed Fence Scale

Using Infeed Fence Stop

Checking/Adjusting