Paragon Outdoor PRH4-1220WT Novara 12 ft. x 20 ft. Louvered Pergola Assembly Instructions

Paragon Outdoor PRH4-1220WT is a 12' x 20' Louver Pergola that provides shade and protection from the elements. It is easy to assemble and can be completed by a team of four people in about two hours. The pergola is made of durable aluminum and is designed to withstand wind and rain. It is also backed by a 10-year warranty. The pergola is a great addition to any backyard or patio and can be used for a variety of purposes such as entertaining, relaxing, or gardening.
PDF
Document
 12&quot; x 20&quot; Louver Pergola
Assembly Instructions
Ар
\ Paragon Group USA
(877) 782 4482 Email:[email protected]
Service:
(O Lo LO LO
Introduction DVDS ВА
Thank you for purchasing the 12’ x 20&quot; Louver Pergola .
When properly assembled and maintained, this gazebo will provide many years of enjoyment!
These instructions include helpful hints and important information needed to safely assemble and properly
maintain the gazebo. Please read these instructions completely before you begin.
Our patented gazebo has been designed for easy assembly. All steps can be completed by a team of
four people. The assembly should take about two hours.
Before Starting Assembly:
CAREFULLY READ ALL THE INSTRUCTIONS BEFORE YOU BEGIN AND FOLLOW THE
STEPS IN THE ORDER THEY ARE PRESENTED.
1.Make sure you have all the necessary parts:
Compare the contents of all cartons to the List of Parts. If any parts are missing or damaged,or
you have any questions, please contact Customer service (877)782 4482before beginning assembly.
2.Lay the parts out in separate staging areas:
The List of Parts has the corresponding step number referenced to each part. We recommend that
while you go through the list, make staging areas for each step and place the parts necessary for
each step in these areas. This will save you time and effort during assembly.
3.Select a Location:
When selecting a location for your gazebo, a flat level area is essential and if possible with proper
water drainage and easy access to power and water, if neccessary.
Choose a sunny, level position away from overhanging trees and power lines and protected from the
wind as much as possible. Locate underground pipes or cables before preparing the site or anchoring
the gazebo.
Note: You may assemble the gazebo on a hard level surface and move it to its final location when
finished. Make sure that there are no obstacles between the assembly area and the final position.
4. Prepare a Foundation:
After choosing a location, proper preparation of the site is recommended. The site must be level.
If the site is not level, create a base slightly larger than the outside dimensions of the gazebo using a
perimeter of two by fours filled with either soil, sod or gravel.
Make sure the base is square by measuring the diagonals from both directions and making sure
they are equal. The gazebo is secured with pegs into holes cast with concrete.
If you decide to have a concrete base, it is best to contact a reliable contractor to make sure it is flat
and level. Make sure you have checked with your local authorities regarding any required building
permits.
5. Make sure you have the proper tools:
* Tape Measure * 2 Small Step Ladders
Work Gloves Wooden Mallet
Safety goggles Scissors and knife
* Phillips Screwdriver ~~ * Liquid soap or WD40 Lubricant
* Spirit Level * Silicon Gel
NOTE: A cordless drill with Phillips head bit is highly recommended but not essential.
2 of 32
Safety Advice Table of Contents
e The gazebo must be positioned and fixed Introduction.................e.eeereme EEE EEE EEE EEE 2
on a flat level surface. Table of Contents... 3
* Dispose of all plastic bags safely. Keep list of Parts...................eeeen 4
them out of the reach of children. Step 1 : Assembling the Lourvers................... 8
* Keep children and pets away from the Sten 2 - С “na the Roof Profil 9
assembly area until the work is completed. tep +: onnecting fhe Root Fro ES
e Always wear shoes, gloves and safety Step 3 : Connecting the Roof Profiles........... 10
goggles when working. Step 4 : Building the Basic Roof Frame........ 12
e Take special care not to touch overhead Step 5 : Building the Corner Profiles............ 18
power lines with the aluminium profiles. Step 6 : Installing the Louvers...................... 20
* Do not attempt fo assemble the gazebo in Step 7 : Installing the Louvers...................... 28
windy or wet conditions. Step 8 : Securing the Gazebo to a Concrete
* Do not position your gazebo in an area Floor or Wood Deck...................... 30
exposed to excessive wind.
e If using power tools or a ladder, always fol-
low the manufacturers safety instructions.
e Hot items such as recently used grills, General Order of Assem bly
blowtorches etc. must not be stored in the
b Step 1 : Assembling the Lourvers
gazebo. | |
e Make sure the gazebo complies with local Step 2 : Connecting the Roof Profiles
building codes. Step 3 : Connecting the Roof Profiles
Step 4 : Building the Basic Root Frame
Step 5 : Building the Corner Profiles
В Step 6 : Installing the Louvers
ATTENTION: Step 7 : Installing the Louvers
DO NOT ATTEMPT TO Step 8 : Securing the Gazebo to a Concrete
ASSEMBLE THE Floor or Wood Deck
PERGOLA ALONE!
)
&pound;
I
3 of 32
|
Qty | Step
2
iffing them.
Be careful when |
les.
99
eas, checking that you have all parts as you go.
, contact customer serv
Vy.
, gloves and go
ing work shoes
removable stickers.
ging ar
ht cartons. These cartons are hea
includ
h
parts for eac
In el
ipped
e edr
dE
is sh
saf
pergola
proper
arts are
Wear
Place all the
The
The
List of Parts
No.
]
; | A PA A DIT
33 ЗЕ SE SE ЗЕ ВЕ SE La G 5
8 Е LO &lt; &copy; N со о &copy; —
4 о 32
ta
Qty | Step
4
2
2
1
2
1
2
2
ns
damaged
step
(877) 782 4482 Email
&lt; N со &lt; = &lt;
s ES = &gt;
N &copy; 38
- \ | 3 с ‚о
N a 5 | a = | &copy; 8
Ш &gt;— a, : о -
_ y 3 S — | 5 3
= &raquo;— € . 2 N &gt; | &gt;
S 3 N Е ой
5 8 CN = | N | 5) 5
&lt; &gt; i
N 5 3 —
2 — &gt;. | =
QO : =
2
2
of 3
5
6 of 32
5 st N N N N 3 со 3 3 x N
a O о о &amp; =&gt; 82 53 SS SS
3 &cent; | 2 | 3 | &cent; | &cent; |v | 28 | 8 | 8 | 5 | &copy;
TT a TT TT Ta
aaa a aa aa
2 о &gt; с 5 o &lt; &gt; со o &copy; =
No. Part Qty | Step | | No. Part Qty | Step
&lt;&gt;
53 Ns 328 [3467] | 58 7 117
Nut 7
1/4&quot; Rocker
&lt;&gt;
54 O 318 | 6,7 | | 59 &copy; 24 | 7
N Y
ul
1/4&quot;
56 156| 6 | | 60 &lt;
Washer
)
57 #2 2 |3 | | 61 Sy 4 | 3
Pin 17a 50mm
We included extra screws for your convenience.
7 of 32
STEP 1 Assembling the Lourvers
Place all the parts on a level surface.
71 Make sure the pieces are in the correct positions before assembling.
Caretully follow the order of assembly to ensure an easy installation.
Wear proper safety gear including work shoes,gloves and goggles.
E Components |
Attach louver connector (15) on
louver (10) by screw (47). A
Louver(10) Louver connector(15) Screw(47)
x 156 x 312 x 624
x 156
IMPORTANT:
Make sure all the louver connectors
installed in correct direction as shown.
8 of 32
STEP 2 Connecting the Roof Profiles 6+7 ~ 8+9
Components |
Roof Profile(6) Roof Profile(7) Roof Profile(8) Roof Profile(9) Corner profile cover(16) Corner profile cover(17)
x 1 x 1 x 1 x 1 x 2 x 2
N NN @&reg; om
Roof Profile Roof Profile Roof Profile Roof Profile
connector(18) connector(19) connector(20) connector(21) Screw(48) Screw(49)
x 2 x 2 x 2 x 2 x 8 x 32
Ey Connect roof profile (6,7) and (8,9) by roof profile
connector (21,20) with screw (48) on the TOP and
screw (49) on the SIDE and BOTTOM as shown.
2.8. Insert roof profile connector (18,19) into roof profile (6/9) and
(7/8), fasten with two screw (49) each as shown.
Attach corner profile cover (16/17) on roof profile (6/9) and
(7/8) by screw (49) underneath of corner profile cover (16/17).
9 of 32
STEP 3 Connecting the Roof Profiles 2+3 ~ 4+5
Components |
Roof Profile(2) | Roof Profile(2A) Roof Profile(3) Roof Profile(3A) Roof Profile(4)
X 2 x 1 x 2 x ] x 2
Se
Roof Profile Roof Profile Roof Profile Roof Profile Roof Profile
connector(20) connector(20A) connector(21) connector(24) connector(25)
x 4 x 2 x 6 x 2 x 2
&gt; &gt;
Roof Profile Roof Profile Roof Profile Roof Profile Roof Profile
connector(33) connector(34) connector(35) connector(35A) connector(36)
x 3 x 6 x 2 x ] x 2
&lt; w gm m
N&eacute;
Controller(45) Ring cap(46) Screw(47) Screw(48) Screw(49)
x 2 x 2 x 4 x 12 x 102
Roof Profile(4A)
x 2
&gt;
Roof Profile
connector(26)
x 2
Y
Roof Profile
connector(36A)
x ]
&lt;&gt;
SY
Nut(53)
x 4
Roof Profile(5)
Roof Profile(5A)
x 2 x 2
=
SS
Roof Profile Roof Profile
connector(27) connector(32)
x 2 x 3
Stopper(38) Corner Profile
cover(43)
x 2 X
Pin(57)
x 2
| З.А Connect roof profile (4A/5,4/5A) by root profile connector
(21,20) with TWO screw (48) on the top of roof profile
connector(21), Exactly as shown, we need the 2 empty holes
tor installing roof profile connector(37) in later step.
Attach 6 screw (49) on the SIDE and BOTTOM of roof profile
connector(20) as shown.
Connect roof profile (5A.4A) by roof connector (21.20A) with two screw (48) on the top of roof profile
connector (21), exactly as shown, we need the 2 empty holes for installing roof profile connector (37) and
corner profile cover (43) in later step.
Attach 4 screw (49) on the side of roof profile connector (21A).
10 of 32
ET Insert roof profile connector (24/25) into hollow ends
of roof profile (5,4) with two predrilled holes facing
inside as shown, and fasten with screw (49).
Insert roof profile connector (26/27) into hollow ends
of roof profile (5,4) with two predrilled holes facing
upward at the same position of roof profile (5,4)
pre-drilled holes as shown for later step.
(49) from underneath.
VIEW FROM INSIDE
underneath as shown.
E Attacg corner profile cover (43) on connector roof profile 4A+5A by 2 screw
Connect roof profile (2,2A/3,3A) by roof profile connector (33,32) with screw
(48) on the TOP and screw (49) on the SIDE and BOTTOM as shown.
3D. Insert roof profile connector (36/35) into hollow ends of roof profile (2,3) and fasten with two
screw (49) on the side and ONE screw (49) at the furthest position of the three pre-drilled holes
Insert roof profile connector (34) into hollow ends of roof profile (2,3) and fasten with ONE screw
(49) at the furthest position of the three pre-drilled holes as shown.
В
_—_
==
mL . A
EN 7: —
NN E -
7
т
us
=
Las Mg
x
11 of 32
VIEW FROM BELOW
Insert roof profile connector (36A/35A) into hollow ends of roof profile (2A,3A) and fasten with
two screw (49) on the side as shown.
Insert roof profile connector (34) into hollow ends of roof profile (2A,3A) and fasten with ONE
screw (49) at the furthest position of the three pre-drilled holes as shown.
VIEW FROM BELOW
ES Insert controller (45) into roof profile (2), fasten with screw (61) and nut (53) to the side of control-
ler (45) as shown.
Attach ring cap (46) to controller (45) from underneath of roof profile (2) by screw (57) as shown.
Attach stopper (38) on roof profile (2) by fasten screw (47) exactly as shown.
STEP 4 Bulding the Basic Roof Frame
Components |
Roof Profile Roof Profile Roof Profile Roof Profile и | (29)
comet 3) oe 4) connector(22) connector(23) ouver mount ouver moun
x 2 x 2 x 2 x 2
4
Louver mount(30) Louver mount(31) roa) Screw(49) Screw(51) Nut(53)
x 6 x 6 x 4 x 66 x 312 x 312
12 of 32
Eve Place roof protile set (5+5A+4A+4) as in U format as shown.
Connect roof profile set to roof profile set (6+7,8+9) by fasten
screw (49) from underneath of corner profile cover (17,16) to roof
profile (4+5) as shown.
17 Ns
A
A VIEWS FROM BELOW |
Connect roof profile set (2+3) on middle of roof profile set
(5+5A+4A+4) by attaching roof profile connector (37) from x
underneath of roof profile set by screw (49).
TIP: Place roof profile set
(2+3) on smooth surface
article to have the same 17
level with roof profile set
for easy installation.
13 of 32
48 Attach roof profile connector (14) to the end of roof profile (2,2A),
fasten with screw (49).
Insert roof profile connector (23,22) into roof profile (7,9), attach roof profile connector (13) to the
end of roof profile (7,4) and (9,5) by screw (49) as shown.
14 of 32
E Attach screw (51) on louver mount (28,29,30,31) with nut (53) as shown.
X 2
x 6
IMPORTANT: В
Screw (51) head must be
vertically installed on louver
mount (28,29,30,31). I
INSIDE VIEW
Insert louver mount (28,29) into roof profile (8+9,6+7) with marked arrow point outward as shown.
Insert louver mount (30,31) into roof profile (3+2,3A+2A) with marked arrow point outward as shown.
ATTENTION:
Louver mounts (28,29,30,31)
are marked, in order to avoid
mistake when inserting.
15 of 32
ET Connect roof profile set (4+4A+5A+5) to roof profile frame by fasten screw (49) from underneath
of corner profile cover (17,16) as shown.
VIEWS FROM BELOW |
Connect roof profile set (2+3) on middle of roof profile set (4+4A/5+5A) by attaching roof profile
connector (37) from underneath of roof profile set by screw (49) as shown.
16 of 32
Attach roof profile connector (14) to the end of roof profile (3,3A), fasten with screw
(49).
Attach roof profile (2A+3A) on corner profile cover(43) by screw (49) from underneath.
Insert roof profile connector (23,22) into roof profile (7,9), attach roof profile connector
(13) to the end of roof profile (7,4) and (9,5) by screw (49) as shown.
Insert roof profile connector (23,22) into roof profile (7,9),
attach roof profile connector (13) to the end of roof profile
(7,4) and (9,5) by screw (49) as shown.
&amp; Using silicon to seal
all the gaps on the
gutter inside roof
profiles.
17 of 32
STEP 5 Building the Corner Profiles
Components |
Align pre-drilled screw holes in corner
profiles(1, 1A) with screw holes in support —
plate(8).
Attach support plate(1 1) to corner profiles(1) as Corner Profile(1) Corner Profile(1A)
shown, using two screws(49) for each plate. х 4 х 2
&lt;&gt; Y mm
Support Plate(11) Support Plate(12) Screw(49)
x 6 x 14 x 68
E Using at least 3 people, lift roof frame.
Align per-drilled screw holes on the top of corner ,
profiles(1) with screw holes on corner profile ATTENTION:
covers(16,17,43). You need at least 4 people to
Insert another three corner profiles(1,1A) as shown, by complete this step!
2 people.
/
[7
18 of 32
E Attach support plates (12) to the botton side of roof frame,
using four screws (49) each as shown.
VIEWS FROM INSIDE
19 of 32
STEP 6 Installing the Louvers
Place 5 piece louvers (10) into pre-installed
screw (51) beside roof profile (5), fasten
with nut (54) on both side of louver (10) as
shown.
DO NOT OVER
TIGHTEN SCREW(54).
ATTENTION: =
6
==
Sm =
Y
&copy;
ue
5
E E
9 &copy;
Components |
Louver O Louver Po Louver tou
&quot;oe
Screw(48) Screw(50) Nut(53) Nut(54) Nut(56)
x 4 x 156 x 4 x 312 x 156
&gt;
IMPORTANT:
Make sure ALL Louvers(10) installed
at the same direction as shown.
‘ Insert one side of the louvers(10)
into screw(51) with a slop, than
place another end.
PERSPECTIVE VIEW
20 of 32
CO Connect louver pullers(39,40) by screw(48) and nut(53)as shown.
Place plastic washer(56) between louver puller sets(39+40) and louver
connectors(15), fasten with screw(50) as shown.
Repeat to assemble louvers(10) on the roof profile frame and connect
with louver puller set(39+40),FIVE pieces louvers(10) at a time.
Repeat to finish left side Louvers.
Ч
IMPORTANT: В ATTENTION:
Louver puller(40) hanger must Screw(50) must fastened
installed at the same side of toward Middie roof
louver connectors(15). , profile(2+3/2A+3A).
y
IMPORTANT:
The Hanger of louver
puller(40) must installed at the
same side of Controller(15).
PERSPECTIVE VIEW
21 of 32
Es Place 5 piece louvers (10) into pre-installed screw
(51) beside roof profile (4),fasten with nut (54) on
both of louver (10) as shown.
~ PERSPECTIVE VIEW
IMPORTANT:
Make sure ALL Louvers(10) installed
at the same direction as shown.
Insert one side of the louvers(10)
into screw(51) with a slop, than
place another end.
a
N
|
ATTENTION:
DO NOT OVER
TIGHTEN SCREW(54).
|
10 A o Je / [Wo
== U
51
&copy; — o
Trae
ua
fi |4
22 of 32
xy Connect louver pullers(39,40) by screw(48) and nut(53)as shown.
Place plastic washer(56) between louver puller sets(39+40) and louver
connectors(15), fasten with screw(50) as shown.
Repeat to assemble louvers(10) on the roof profile frame and connect
with louver puller set(39+40),FIVE pieces louvers(10) at a time.
Repeat to finish left side Louvers.
&gt;
IMPORTANT: ATTENTION: |
Louver puller(40) hanger must Screw(50) must fastened
installed at the same side of toward Middie roof
louver connectors(15). profile(2+3,2A+3A).
IMPORTANT:
The Hanger of louver
puller(40) must installed at the
same side of Controller(15).
PERSPECTIVE VIEW
23 of 32
x3 Place 5 piece louvers (10) into pre-installed screw
(51) beside roof profile (5), fasten with nut (54) on | .
both side of louver (10) as shown.
| - ] Г
x PERSPECTIVE VIEW
IMPORTANT:
Make sure ALL Louvers(10) installed
at the same direction as shown.
Insert one side of the louvers(10)
into screw(51) with a slop,than
place another end.
a
VAN
al an |
|
|]
ATTENTION:
DO NOT OVER
|
O_ Le ft
— &gt; &gt; =
77 A AR
Qu
7 18
24 of 32
&gt; Connect louver pullers(39,40) by screw(48) and nut(53)as shown.
Place plastic washer(56) between louver puller sets(39+40) and louver
connectors(15), fasten with screw(50) as shown.
Repeat to assemble louvers(10) on the roof profile frame and connect
with louver puller set(39+40),FIVE pieces louvers(10) at a time.
Repeat to finish left side Louvers.
IMPORTANT:
Louver puller(40) hanger must
installed at the same side of
louver connectors(15).
ATTENTION:
Screw(50) must fastened
toward Middie roof
profile(2+3,2A+3A).
N
IMPORTANT:
The Hanger of louver
puller(40) must installed at the
same side of Controller(15).
PERSPECTIVE VIEW
25 of 32
x’ Place 5 piece louvers (10) into pre-installed screw 6
(51) beside roof profile (4),fasten with nut (54) on
both of louver (10) as shown.
~ PERSPECTIVE VIEW
IMPORTANT:
Make sure ALL Louvers(10) installed
at the same direction as shown.
Insert one side of the louvers(10)
into screw(51) with a slop, than
a
place another end. ATTENTION:
DO NOT OVER
TIGHTEN SCREW(54).
|
&yuml;
TO
\
&reg;
J Y
&lt;&lt; Y
MUSA
uu
EA
26 of 32
Кв Connect louver pullers(39,40) by screw(48) and nut(53)as shown.
Place plastic washer(56) between louver puller sets(39+40) and louver
connectors(15), fasten with screw(50) as shown.
Repeat to assemble louvers(10) on the roof profile frame and connect
with louver puller set(39+40),FIVE pieces louvers(10) at a time.
Repeat to finish left side Louvers.
D,
IMPORTANT: ATTENTION:
Louver puller(40) hanger must Screw(50) must fastened
installed at the same side of toward Middie roof
louver connectors(15). profile(2+3,2A+3A).
IMPORTANT:
The Hanger of louver
puller(40) must installed at the
same side of Controller(15).
PERSPECTIVE VIEW
27 of 32
STEP 7 Installing the Louvers
Components |
E Assemble one side of two puller connec-
tors (42) to controller (45) with screw (52)
assemble though TWO screws (53) at &cent;
sach oe о controler (45) and fasten Puller connector(42) Controller cover(44) Screw(47) Screw(48)
with nuts . x 4 x 2 x 8 x 4
Connect another side of puller connectors =
(42) to louver pullers (40,41), fasten with
screws (48) and nuts (54). бу O —
Attach controller cover (44) to the top of Screw(52) Nut(53) Nut(54) Rocker(58)
controller (45) pre-drilled nole by four х 2 х 8 x 6 x ]
screws (47).
Attach controller cap (44) to contorller
(42),using screw(47) as shown.
|
jm — 0, E |
a = E
— ar
28 of 32
Wu
nier
&copy;
nd cou
of.
p(46) clockwise a
ng ca
the louver ro
Ш
Using Rocker(58) turning the ri
nd close
clockwise to open a
VIEWS FROM BELOW
VIEWS FROM BELOW
VIEWS FROM BELOW
STEP 8 Securing the Gazebo to a Concrete
Floor or Wood Deck
Concrete Floor:
NA
1.Using a concrete drill, drill holes into the concrete floor, Q B= 990
corresponding to the holes in support plates (8). Concrete Bolts, washers
2. Insert concrete bolts into the holes and hammer into place, using a mallet.
3. Fasten concrete bolts with washers and nuts.
(59)
x 24
\ И X y
Wood Deck:
1.Using an electric wood drill, drill holes into the wood floor, Ph
corresponding to the holes in support plates (8). Wood Bolts, washers X 24
2. Insert wood screws with washers (not supplied) into the holes and fasten, NOT SUPPLIED
using an electric screw driver. to be purchased by user
30 of 32
Center of
Post/Footing 1910.07
_ Measurements 604 4.8mm _
9'7.8&quot;] 9'7.8&quot;]
TH 2942.4mm E 2942.4mm =H
Es SE
&deg; &deg; ’, &lt;
2 De
PE = = | о Е
ия co —
SS 5 SE SE
— 8 3 — O| сч &copy;
— LN 3 -2 E
Im с — 8 8
97.8&quot; 197.8]
Я 2942.4mm и 2942.4mm =)
6.3in]
160mm
[6.3in]
7
160mm
Post Mount
Post Detall
31 of 32
12&quot; x 20’ Louver Pergola
Assembly Instructions
WARRANTY:
Warranty covers damage due to manufacturing defects only for a
period of 5 years on the structure from date of purchase. Warranty
does not cover weather inflicted damage and/or damages causes
caused by not following assembly instructions and adhering to warn-
ings in manual. Warranty does not cover user error, negligence, or
misuse.
N В,
CA WARNING: Cancer and Reproductive Harm- в
www.P65Warnings.ca.gov.
/N AVERTISSEMENT: Cancer et Troubles de |' appareil reproducteur-
www.P65Warnings.ca.gov.
(&Agrave; ADVERTENCIA: C&aacute;ncer y Da&ntilde;o Reproductivo-
www.P65Warnings.ca.gov. В
@ &Oacute;N
Fagen ) Paragon Group USA
t ice: 2 4482 Email:cs-out
_ 06 oparagonoudoorcompany Customer Service:(877) 78 8 mail:[email protected] &gt;
">
Hello! I am an AI chatbot specifically trained to assist you with the Paragon Outdoor PRH4-1220WT Assembly Instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!
Show related prompts