Christie D12WU-H 1DLP dual-lamp digital projector series User manual

Christie D12WU-H 1DLP dual-lamp digital projector series User manual
USER MANUAL
020-000772-02
H Series
D12HD-H/D12WU-H
The CD included with this printed manual contains an electronic copy in English. Please read all instructions before
using or servicing this product.
Le DC fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les
instructions avant d'utiliser ou de réparer ce produit.
Die mit dieser gedruckten Anleitung gelieferte CD enthält eine elektronische Kopie in Deutsch. Bitte lesen Sie alle
Anweisungen, bevor Sie dieses Produkt verwenden oder warten.
Il CD fornito con il manuale stampato contiene una copia elettronica in lingua italiano. Si prega di leggere tutte le
istruzioni prima di utilizzare o riparare questo prodotto.
El DC incluido con este manual impreso contiene una copia electrónica en español. Por favor, lea todas las
instrucciones antes de usar o dar servicio a este producto.
NOTICES
COPYRIGHT AND TRADEMARKS
Copyright ©2015 Christie Digital Systems USA, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their
respective holders.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the product is operated in a commercial environment. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of the product in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at the user's own expense.
WARNING! Changes or modifications not expressly approved by Christie could void the user's
authority to operate the product.
FOR COMMERCIAL USE ONLY - POUR USAGE COMMERCIAL UNIQUEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING 2 CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
CET APPAREIL NUMÉRIQUE DE CLASSE A EST CONFORME AUX NORMES DÉFINIES DANS
LES RÉGLEMENTATIONS CANADIENNES SUR LES APPAREILS CAUSANT DES
INTERFÉRENCES RADIO (CANADIAN INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS, ICES-003, CLASS A).
!
!
!
!
!
-!
!
! !
!
!
!
!
!
!
!
!
/
!
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products or
availability could occur which may not be reflected in this document. Christie reserves the right to
make changes to specifications at any time without notice. Performance specifications are typical,
but may vary depending on conditions beyond Christie's control such as maintenance of the
product in proper working conditions. Performance specifications are based on information
available at the time of printing. Christie makes no warranty of any kind with regard to this material,
including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be
liable for errors contained herein or for incidental or consequential damages in connection with the
performance or use of this material.
The product is designed and manufactured with high-quality materials and components that can be
recycled and reused. This symbol
means that electrical and electronic equipment, at their end-
of-life, should be disposed of separately from regular waste. Please dispose of the product
appropriately and according to local regulations. In the European Union, there are separate
collection systems for used electrical and electronic products. Please help us to conserve the
environment we live in!
Canadian manufacturing facility is ISO 9001 and 14001 certified.
GENERAL WARRANTY STATEMENTS
For complete information about Christie's limited warranty, please contact your Christie dealer. In
addition to the other limitations that may be specified in Christie's limited warranty, the warranty
does not cover:
a. Damage occurring during shipment, in either direction.
b. Problems caused by combination of the product with non-Christie equipment, such as
distribution systems, cameras, video tape recorders, etc., or use of the product with any nonChristie interface device.
c. Damage caused by misuse, improper power source, accident, fire, flood, lightening,
earthquake or other natural disaster.
d. Damage caused by improper installation/alignment, or by product modification, if by other than
a Christie authorized repair service provider.
e. For LCD projectors, the warranty period specified applies only where the LCD projector is in
"normal use". "Normal use" means the LCD projector is not used more than 8 hours a day, 5
days a week. For any LCD projector where "normal use" is exceeded, warranty coverage under
this warranty terminates after 6000 hours of operation.
f. Failure due to normal wear and tear.
g. Projector lamps (See Christie’s separate lamp program policy).
h. Damage caused by use of a projector lamp beyond the recommended lamp life, or use of a
lamp supplied by a supplier other than Christie.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your
product. Please see the Maintenance section for specific maintenance items as they relate to your
product. Failure to perform maintenance as required, and in accordance with the maintenance
schedule specified by Christie, will void the warranty.
Table of Contents
1. SAFETY
2. INTRODUCTION
2.1
2.2
2.3
2.4
2.5
Projector Components .................................................................................................. 2-1
Built-in Keypad .............................................................................................................. 2-4
Input/Output (I/O) Panel ................................................................................................ 2-5
Remote Control ............................................................................................................. 2-6
LED Status Indicators ................................................................................................... 2-8
3. INSTALLATION
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
Connect to Computer .................................................................................................... 3-1
Connect to Video Equipment ........................................................................................ 3-2
Turn the Projector On.................................................................................................... 3-3
Turn the Projector Off.................................................................................................... 3-3
Adjust the Projector Position ......................................................................................... 3-4
Calculate Lens Offset.................................................................................................... 3-6
Removing and Installing the Lens ............................................................................... 3-10
Fuse Installation .......................................................................................................... 3-11
Filter Replacement ...................................................................................................... 3-12
Ceiling Mount Installation ............................................................................................ 3-12
4. OPERATION
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
Size and Position Menu ................................................................................................ 4-2
Image Settings Menu .................................................................................................... 4-6
Configuration Menu....................................................................................................... 4-9
Lamp ........................................................................................................................... 4-14
Status Menu ................................................................................................................ 4-16
Input Switching & PIP Menu........................................................................................ 4-18
Language Menu .......................................................................................................... 4-20
Test Pattern Menu....................................................................................................... 4-20
Web User Interface ..................................................................................................... 4-21
4.9.1 Logging On..................................................................................................... 4-21
4.9.2 Main Tabbed Page - General ......................................................................... 4-21
4.9.3 Main Tabbed Page - Status............................................................................ 4-22
4.9.4 Main Tabbed Page - Lens .............................................................................. 4-22
4.9.5 Network .......................................................................................................... 4-23
4.9.6 Tools............................................................................................................... 4-26
4.9.7 Administrator Page......................................................................................... 4-26
4.9.8 About Page..................................................................................................... 4-27
4.10 Christie Presenter ....................................................................................................... 4-28
4.10.1 Connect to the Projector................................................................................. 4-28
4.10.2 Install Christie Presenter software.................................................................. 4-29
4.10.3 Use Christie Presenter ................................................................................... 4-30
4.11 Card Reader Operation............................................................................................... 4-36
5. TROUBLESHOOTING
6. SPECIFICATIONS
6.1
6.2
i
Inputs ............................................................................................................................ 6-1
PIP/POP Compatibility .................................................................................................. 6-7
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Table of Contents
6.3
6.4
6.5
6.6
6.7
6.8
Key Features ................................................................................................................ 6-8
List of Components....................................................................................................... 6-8
Optional Accessories .................................................................................................... 6-9
REGULATORY ............................................................................................................. 6-9
Federal Communications Commission (FCC) Warning.............................................. 6-10
OSD Tree.................................................................................................................... 6-11
H Series User Manual
020-000772-02 Rev.1 (08-2015)
ii
Section 1: SAFETY
1.
SAFETY
Read through this document in its entirety and understand all warnings and
precautions before attempting to operate the projector.
.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1-1
WARNING
Do not look into the projector lens when the lamp is on. The bright light may
result in permanent eye damage.
To reduce the risk of fire or electric shock, do not expose this projector to
rain or moisture.
Do not open or disassemble the projector as this may cause electric shock.
All installation and maintenance procedures must be performed by a
Christie accredited service technician.
Keep all combustible material away from the concentrated light beam of the
projector.
Position all cables where they cannot contact hot surfaces or be pulled or
tripped over.
Always power down the projector and disconnect all power sources before
servicing or cleaning.
Use a soft cloth moistened with a mild detergent to clean the display
housing.
Disconnect the power plug from the AC outlet if the product is not being
used for an extended period of time.
Operate the projector under the following conditions:
- Operating temperature range: 0°C to 40°C
- Storage temperature range: -10°C to 60°C
- Humidity range: 10% to 85 % RH (Max.), non condensing
- Operating altitude: 10,000 ft. maximum
Use only the AC power cord supplied. Do not attempt operation if the AC
supply and cord are not within the specified voltage and power range for
your region.
Remove the lens plug from the lens opening in the projector before
installing the lens. Retain the lens plug to protect the optical components
from dust and debris during transport.
Do not block the ventilation slots and openings on the projector.
Do not use abrasive cleaners, waxes or solvents to clean the projector.
Do not allow anything to rest on the power cord.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 1: SAFETY
H Series User Manual
020-000772-02 Rev.1 (08-2015)
1-2
Section 2: INTRODUCTION
2.
INTRODUCTION
The product specified in this document is a high brightness, high-resolution
video/graphics 1-chip lamp based projector. The projector is available in HD
and WUXGA resolutions. The projector utilizes Digital Light Processing (DLP®)
technology from Texas Instruments. It is primarily designed for fixed installation
markets.
2.1
Projector Components
Front View
1
2
3
Ind.
2-1
Part Name
Description
1
Front IR Sensor
Receive signals from the IR remote. Keep the signal
path to the sensor unobstructed for uninterrupted
communication with the projector.
2
Projection Lens
Allow automated lens control and adjustment: vertical
and horizontal offsets, zoom and focus.
3
Adjustable Feet
Raise or lower the feet to level the projector.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 2: INTRODUCTION
Rear View
1
2
3
4
Ind.
Part Name
Description
1
LED status Indicators
Display the status of the projector. They are (from left
to right): LAMP1, LAMP2.
2
Rear IR Sensor
Receive signals from the IR remote. Keep the signal
path unobstructed for uninterrupted communication
with the projector.
3
Lamp Door
Use the lamp door to access the lamp module.
4
Cooling Air Vents
(Exhaust)
Keep these vents unobstructed to prevent the
projector from overheating.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
2-2
Section 2: INTRODUCTION
Left View
1
Right View
2
3
4
5
6
Ind.
2-3
Part Name
Description
1
Cooling Air Vents
(Intake)
Keep these vents unobstructed to prevent the
projector from overheating.
2
Input/Output (I/O) Panel
Connect the projector to external devices.
3
Built-in Keypad
Control the projector.
4
Power Button
Switch the power button to turn on the power source.
5
AC Input
Connect to the supplied power adapter.
6
Kensington Lock
Use to secure the projector to countertops, tables, and
so on.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 2: INTRODUCTION
2.2
Built-in Keypad
1
7
8
2
9
3
4
10
5
11
12
6
Ind.
Part Name
Description
1
Auto
Automatically optimize image.
2
Power
Turn the projector on or off.
3
Shutter
Display or blank the video image.
4
OSD
Use to hide or show OSD menus.
5
Help
Display the instruction for source connection.
6
Menu
Display menus.
7
Arrow keys
•
•
8
Input
Select an input for the main or PIP/PBP image.
9
Focus
Adjust focus.
10
Lens
Adjust the lens vertical or horizontal offset setting.
11
Zoom
Adjust zoom.
12
Back
Return to previous level or exit menus if at top level.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Adjust a setting UP or DOWN
Navigate within a menu
2-4
Section 2: INTRODUCTION
2.3
Input/Output (I/O) Panel
1
2
3
4
3D SYNC OUT
DVI
VGA IN
VGA OUT
3D SYNC IN
RS232
5
RED/PR
GREEN/Y
BLUE/PB
MINI USB
ETHERNET
H
V
DISPLAY PORT
CVBS
3D-SDI
HDBaseT
HDMI-1
7
6
Ind.
2-5
8
Connector Name
9
10
USB
11
REMOTE IN
12 13
Ind.
REMOTE OUT
14
15
Connector Name
1
3D Sync OUT
9
3G-SDI
2
DVI-D
10
HDMI-1
3
VGA IN
11
USB
4
VGA OUT
12
MINI USB
5
Component IN
13
Ethernet
6
3D Sync IN
14
HDBaseT
7
RS232
15
Remote OUT/IN
8
CVBS
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 2: INTRODUCTION
2.4
Remote Control
1
2
16
SHUTTER
17
3
18
4
5
19
20
6
VGA
BNC
HDMI1
21
7
HDMI2
DVI-D
DP
3G-SDI
HDBaseT
CVBS
22
8
9
10
PRESENT.
23
24
25
11
26
12
27
13
14
28
15
29
Use a cable length of 20 m or less, if the length of cable exceeds 20 m, the
remote control may not work normally.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
2-6
Section 2: INTRODUCTION
Ind.
2-7
Part Name
Description
1
SHUTTER
Display or blank the video image.
2
Power on
Turn projector ON.
3
Gamma
Adjust mid-range levels.
4
Bright
Adjust amount of light in the image.
5
PIP/PBP
Turn PIP/PBP ON/OFF.
6
Size
Adjust the PIP/PBP size.
7
Number Keys
Enter a number, such as a channel, value, and so on.
8
Help
Display the instruction for source connection.
9
Menu
Display menus.
10
Arrow Keys
•
•
11
Test
Display a test pattern.
12
Auto
Automatically optimize image.
13
OSD
Use to hide or show OSD menus.
14
Keystone H
Adjust the horizontal keystone.
Adjust a setting UP or DOWN.
Navigate within a menu.
15
Keystone V
Adjust the vertical keystone.
16
Standby
Turn projector OFF.
17
Contrast
Adjust difference between dark and light.
18
Hot-key
Select your preset keys quickly.
19
Swap
Swap the main and PIP/PBP images.
20
Layout
Adjust the PIP/PBP layout.
21
Focus
Adjust focus to improve image clarity as desired.
22
Zoom
Adjust zoom to achieve a desired image size.
23
Proj Key
Change the remote ID. Press Proj Key then a number
between 1 and 9 to assign an ID. Press PROJ then
number 0 to return to the universal remote ID.
24
Exit
Return to previous level or exit menus if at top level.
25
Enter
•
•
26
Input
Select an input for the main or PIP/PBP image.
27
Info
Display source image information.
28
Lens H
Horizontal Lens Shift - Adjust the position of the image
horizontally.
29
Lens V
Vertical Lens Shift - Adjust the position of the image
vertically.
Select a highlighted menu item.
Change or accept a value.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 2: INTRODUCTION
2.5
LED Status Indicators
The LED status indicators are located on the right side of the projector. Each
LED is defined below.
•
LAMP LED
LED Status
Projector State
Red (Short blink)
Fail to strike lamp after attempts. (Strike attempts stop.)
Red (Solid)
Lamp has unexpectedly shut down. (System goes into cool
down state.)
Yellow (Solid)
Lamp time has expired and lamp should be replaced.
(Projector also begins to display the replaced lamps OSD
message at startup.)
Green (Solid)
Lamp is on and operating correctly.
Green (short blink)
Projector lamp is switching on.
Off
Lamp is off.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
2-8
Section 2: INTRODUCTION
•
STATUS LED
LED Status
•
Off
AC power is off (without AC plug in).
Green (Flashing)
Projector is startup or in cool down mode.
Green (Solid)
System is operating stablely.
Blue (Flashing)
Projector is cooling down.
Blue (Solid)
AC has been applied, projector is in standby mode.
Yellow (Flashing)
Warning is an attention state that does not cause the projector
to shutdown. The dynamic black error or entering high altitude
mode is due to over temperature of lamp driver.
Yellow (Solid)
Projector is turning off by the end user while projector is
warning.
Red (Flashing)
Error is an attention state that has caused or may inevitably
cause projectore shutdown. (Fan failure, over temperature,
Fliter install Failure, CW Failure.)
Red (solid)
Projector is turning off by the end user while projector is
warning.
White (Flashing)
Projector is in flash(LAN) update state.
SHUTTER LED
LED Status
2-9
Projector State
Projector State
Off
Lamp is on - image is displayed
Magenta (Solid)
Lamp is on - image is blank
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 2: INTRODUCTION
H Series User Manual
020-000772-02 Rev.1 (08-2015)
2-10
Section 3: INSTALLATION
3.
INSTALLATION
3.1
Connect to Computer
Laptop
Desktop
9
1
3D SYNC OUT
2
3
4
DVI
VGA IN
VGA OUT
5
RED/PR
6
GREEN/Y
BLUE/PB
MINI USB
ETHERNET
7
H
8
V
DISPLAY PORT
3D SYNC IN
RS232
CVBS
3D-SDI
HDBaseT
HDMI-1
Ind.
Connector Name
Ind.
USB
Connector Name
REMOTE OUT
REMOTE IN
Ind.
Connector Name
1
DVI Cable
4
VGA out Cable
7
USB Type A Cable
2
RS232 Cable
5
HDMI Cable
8
USB Type B Mini Cable
3
VGA in Cable
6
DisplayPort Cable
9
Power Cord
NOTE:



3-1
The diagram shows the cables/connectors that may be used to connect to various
devices.
Due to the difference in applications for each country, the accessories required in some
regions may be different from those shown.
This diagram is for illustrative purposes only, and does NOT indicate that these
accessories are supplied with the projector.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 3: INSTALLATION
3.2
Connect to Video Equipment
Component video output equipment
DVD player
Video cassette recorder
2
4
6
1
7
3
5
3D SYNC OUT
DVI
VGA IN
VGA OUT
RED/PR
GREEN/Y
BLUE/PB
MINI USB
ETHERNET
H
V
DISPLAY PORT
3D SYNC IN
RS232
CVBS
3D-SDI
HDBaseT
HDMI-1
Ind.
Connector Name
Ind.
USB
REMOTE OUT
REMOTE IN
Connector Name
1
CVBS Cable
5
15-pin to 3 RCA Component/HDTV
Adapter
2
VGA to RBG SCART
6
HDMI Cable
3
VGA in Cable
7
Component (YPbPr) Cable
4
3 RCA Component Cable
NOTE:



The diagram shows the cables/connectors that may be used to connect to various devices.
Due to the difference in applications for each country, the accessories required in some
regions may be different from those shown.
This diagram is for illustrative purposes only, and does NOT indicate that these
accessories are supplied with the projector.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
3-2
Section 3: INSTALLATION
3.3
Turn the Projector On
1. Ensure that the power cord and signal cable are securely connected. The
Power button on the built in keypad is illuminated.
2. Turn on the projector by pressing " " on the remote control or press " "
on the built-in keypad. The Status LED is Green with a long blink. 12
3. Turn on the source. Select Input Key on the remote control to select an
input source (VGA, BNC, HDMI, Component, S-Video or Composite
Video). 13
4. The projector detects the source you selected and displays the image.
NOTE:

The first time the projector is used, the preferred language may be selected from the main
menu after the startup screen is displayed.
2
1
Power on
SHUTTER
2
1
Power on
VGA
BNC
HDMI2
DVI-D
HDMI1
DP
3G-SDI
HDBaseT
CVBS
PRESENT.
3
1
3.4
Input Key
Turn the Projector Off
1. Press " " on the built-in keypad or on the remote control to turn off the
projector. A warning message appears on the displayed image.
2. Press " " again to confirm your selection. If you do not press " " again,
the warning message disappears after three seconds.
3-3
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 3: INSTALLATION
3.5
Adjust the Projector Position
When you select a position for the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Follow these general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The
projector (with the standard lens) must be at least 3 feet (0.9m) from the
projection screen.
• Position the projector to the required distance from the screen. The
distance from the lens of the projector to the screen, the zoom setting, and
the video format determine the size of the projected image.
• For the fixed short lens, the image exits at a default angle. However, the
lens shift feature makes the image offset variable.
• Lens throw ratio:
- Lens 1.2~1.5 (WU/HD)
- Lens 1.5~2.0 (WU/HD)
- Lens 2.0~4.0 (WU/HD)
• 360 degree operation (along the widest axis)
360°
NOTE:

The max tilt of lamp axis from horizontal is ±20 degrees.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
3-4
Section 3: INSTALLATION
Portrait Mode
-
The projector is in portrait mode when the viewing angle is from 70° to
110° as illustrated below.
Portrait mode
90~110 deg
Portrait mode
70~90 degree
Portrait mode
90 degree
Non-Supported Modes
-
The projector is in non-portrait mode when the viewing angle is 250° to
290° as illustrated below.
The "red" status LED on projector lights on.
270~290 degree
250~270 degree
•
3-5
270 degree
WARNING
The projector should not be operated in Non-Portrait Mode.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 3: INSTALLATION
3.6
Calculate Lens Offset
•
•
The vertical image offset (shift) ranges for the projector are +/-120%
(WUXGA) and +/-140% (HD). The horizontal image offset (shift) range for
the projector is +/-50% (HD/WUXGA).
The method for calculating lens offset complies with Industry standards.
Example for Vertical lens offset:
- At 0% offset (or on axis), the center of the image is on the lens center,
so that half of the image appears above and half appears below the
lens center.
- At +100% offset, all (or 100%) of the image appears above the lens
center.
- The % offset is calculated as the ratio of the number of pixels shifted up/
down to half the image size. Examples for WUXGA:
 Shifting up 600 pixels gives offset of 600/600 * 100% = 100%
 Shifting down 600 pixels gives offset of -600/600 * 100% = -100%
 Shifting up 720 pixels gives offset of 720/600 * 100% = 120%
 Shifting up 240 pixels gives offset of 240/600 * 100% = 40%
WUXGA Projectors:
Vertical Image Offset: 0% Offset (WUXGA)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
600 pixels
above lens
center.
Lens center
600 pixels
below lens
center.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
3-6
Section 3: INSTALLATION
Vertical Image Offset: 120% Offset (WUXGA)
Image has been offset 720 pixels above
lens center, so the center of the image is
now 720 pixels above where the center of
the image was at 0% offset (or lens center).
The offset is +720/600 * 100% = +120%.
720 pixels of
shift above
lens center.
Lens center
Vertical Image Offset: -120% Offset (WUXGA)
Image has been offset 720 pixels below lens
center, so the image has an offset of -720/
600 * 100% = -120%
720 pixels
of shift
below lens
center.
Lens center
Total of
1440 pixels
(720+720)
of display
are below
lens center.
3-7
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 3: INSTALLATION
HD Projectors:
Vertical Image Offset: 0% Offset (HD)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
540 pixels
above lens
center.
Lens center
540 pixels
below lens
center.
Vertical Image Offset: 140% Offset (HD)
Image has been offset 756 pixels above
lens center, so the center of the image is
now 756 pixels above where the center of
the image was at 0% offset (or lens center).
The offset is +756/540 * 100% = +140%.
756 pixels of
shift above
lens center.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Lens center
3-8
Section 3: INSTALLATION
Vertical Image Offset: -140% Offset (HD)
Image has been offset 648 pixels below lens
center, so the image has an offset of -756/
540 * 100% = -140%
Lens center
756 pixels
of shift
below lens
center.
Total of
1512 pixels
(756+756)
of display
are below
lens center.
Horizontal Image Offset: +/-50% Offset
1920 pixels
+480 pixels
Lens center
-480 pixels
Image has been offset 480 pixels
left or right of lens center.
The image has an offset of +480/
960 * 100% = +50%, or -480/960 *
100% = -50%
3-9
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 3: INSTALLATION
3.7
Removing and Installing the Lens
When handling the projector after lens installation, make sure the front lens
cap is placed on the lens to protect the lens surface from potential damage.
When carrying or moving the projector, do not handle by the lens. This may
damage the lens, the chassis or other mechanical parts within the projector.
Installation Steps:
1. Center the lens: Ensure that the lens is at or near its center position.
Attempting to remove the lens when at a large offset may cause damage to
the lens assembly. Center the lens while the projector is switched on by
pressing the lens horizontal or vertical button and then pressing Enter.
2. Turn Off the projector: Turn the projector OFF.
3. Wait for projector to cool down: Allow the projector to cool down into
standby mode before replacing the lens. Remove power cord after the
projector has cooled down and prior to replacing the lens.
4. Remove the lens: Press lens release button and rotate the lens counterclockwise by a quarter to release the lock. Remove the lens through the
front of the projector.
5. Install the new lens: Fully insert the lens assembly straight into the lens
mount without turning. Rotate the lens cap clockwise to lock the lens in
place.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
3-10
Section 3: INSTALLATION
3.8
Fuse Installation
1. Turn off the projector: Turn the projector off.
2. Wait for projector to cool down: Allow the projector to cool down into
standby mode.
3. Take off rear fan cover by releasing one screw on the cover.
4. Release the fuse and replace the new one.
NOTE:

3-11
For high rating region (200~240v), it should use a 10 amp or 15 amp fuse.
For low rating region (100~120v), it should use a 20 amp or 15 amp fuse.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 3: INSTALLATION
3.9
Filter Replacement
1. Turn off the projector.
2. Wait for projector to cool down: Allow the projector to cool down into
standby mode.
3. Remove the filter cover by pushing down it.
4. Release the filter by pulling out and replace it.
3.10
Ceiling Mount Installation
Mount the projector with an appropriate mounting kit, using the four mounting
points on the underside of the projector.
•
•
When not mounted properly, the projector may fall, causing hazards or
injury. The warranty on this projector does not cover any damage caused
by the use of any non-recommended ceiling mount kit or installation of the
ceiling mount kit in an improper location.
Refer to the installation instructions and safety guidelines provided in the
kit.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
3-12
Section 4: OPERATION
4.
OPERATION
The projector has multilingual On-Screen Display (OSD) menus that allow you
to make image adjustments and change a variety of settings.
•
•
•
•
•
Most of the projector controls are accessed from within the projector menu
system. There are several groups of related functions, with each group
selectable from the Main menu as shown below. Press the MENU button on
the remote control or on the built-in keypad on the rear of the projector to
display the main menu.
Use the arrow keys to navigate within the menu and adjust a setting up or
down.
Press ENTER to select a highlighted menu item or use it to change or
accept a value.
Select the next item that you want to adjust in the menu and adjust it as
described above.
Press EXIT to return to the previous menu or exit menus if at top level.
Main Menu
1. Size & Position
2. Image settings
3. Configuration
4. Lamp
5. Status
6. Input Switching & PIP
4-1
7. Language
English
8. Test pattern
OFF
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
4.1
Size and Position Menu
Size & Position
1. Size Presets
Auto
2. Overscan
OFF
3. Pixel Track
4. Pixel Phase
5. Horz Position
6. Vert Position
7. Digital Horz Zoom
8. Digital Vert Zoom
9. Digital Horz Shift
10. Digital Vert Shift
11. Geometry Correction
OFF
12. Auto Image
Size Presets
Display an image with the detected size, or resize the image by maximizing
either the height, width or both, or resize to the maximum size possible while
keeping the original aspect ratio.
• Auto: Display with the detected size.
• Native: Display in its native resolution.
• 4:3: Retain 4:3 aspect ratio.
• Letterbox: Make the active content enlarge to the full screen.
• Full Size: Fill the screen (regardless of the source).
• Full Width: Fill display width and keep aspect ratio.
• Full Height: Fill display height and keep aspect ratio.
• Custom: Stretch the display horizontally or vertically without cutting the
image display.
Overscan
Remove noise around the image. Overscan Zoom enlarges image 6% from
original size. Overscan Crop cuts 6% of active pixels in four edges of original
image.
Pixel Track
Analog RGB signals only. Steady flickering or several soft vertical stripes or
bands across the entire image indicates poor pixel tracking. Proper pixel
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-2
Section 4: OPERATION
tracking ensures that the image quality is consistent across the screen, the
aspect ratio is maintained, and that the pixel phase can be optimized.
Pixel Phase
Analog RGB Signals only. Adjust pixel phase when the image still shows
shimmer or noise after pixel tracking is optimized. Pixel phase can adjust the
phase of the pixel-sampling clock relative to the incoming signal.
Horz Position
Move the image right or left within the area of available pixels.
Vert Position
Move the image up or down within the area of available pixels.
Digital Horz Zoom
Change the size of projector's display area horizontally. If the display area has
been resized by this setting, it can be moved by changing the Digital Horz Shift
and Digital Vert Shift settings.
Digital Vert Zoom
Change the size of projector's display area vertically. If the display area has
been resized by this setting, it can be moved by changing the Digital Horz Shift
and Digital Vert Shift settings.
Digital Horz Shift
Move the display area horizontally if its size has been changed by the Digital
Zoom setting.
Digital Vert Shift
Move the display area vertically if its size has been changed by the Digital
Zoom setting.
Geometry Correction
Provides two ways for warping control.
1. PC Mode off:
User can do simple horizontal/vertical keystone, pincushion, barrel control by
using OSD.
2. PC Mode on:
User can do arbitrary warping or blending control by using PC APP provided
separately.
4-3
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
Geometry Correction Feature Compatibility
4-Corner
Curved
Surface(2x2)
Keystone
Pincushion and
Barrel
Rotation
4-Corner
--




Curved
Surface(2x2)

--
X
X
X
Warp Function
Keystone

X
--

X
Pincushion and
Barrel

X

--
X
Rotation

X
X
X
--
•
•
OFF: No Geometric correction is applied to the image.
Horiz Keystone: Adjust the keystone horizontally to make the image more
square. Horizontal keystone is used to correct a keystoned image shape in
which the left and right borders of the image are unequal in length, and the
top and bottom are slanted to one of the sides. This is intended for use with
horizontally on-axis applications. For horizontally offset applications, you
must use four Corner correction using the optional Dual Processor Warp
Module.
B
B
A
•
Ind.
1080P
WUXGA
A
30.60%
30.34%
B
14.20%
12.86%
A
Vert Keystone: Adjust the keystone vertically to make the image more
square. Vertical keystone is used to correct a keystoned image shape in
which the left and right borders of the image are unequal in length, and the
top and bottom are slanted to one of the sides. This is intended for use with
horizontally on-axis applications. For horizontally offset images, you must
use four Corner correction using the optional Dual Processor Warp Module.
B
A
H Series User Manual
020-000772-02 Rev.1 (08-2015)
B
A
Ind.
1080P
WUXGA
A
5.12%
5.04%
B
11.00%
10.52%
4-4
Section 4: OPERATION
•
Horiz Pincushion: Adjust the pincushion horizontally and make the image
more square.
Ind.
A
•
WUXGA
5.17%
5.39%
B
5.17%
4.24%
B
Vert Pincushion: Adjust the pincushion vertically and make the image more
suqare.
A
•
1080P
A
B
Ind.
1080P
WUXGA
A
9.67%
7.44%
B
9.83%
7.58%
Pincushion/Barrel: Allow for correction for slight curved distortion from the
lens or projection surface
A
B
C
D
Ind.
1080P
WUXGA
A
9.19%
7.44%
B
5.28%
5.39%
C
8.65%
6.87%
D
3.76%
3.36%
Auto Image
Force the projector to reacquire and lock to the input signal. This is useful
when signal quality is marginal. "Normal mode" can support all of the 4:3 input
sources.
"Wide mode" can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (for
example 1400 x 1050), perform Auto Image using "normal mode".
4-5
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
4.2
Image Settings Menu
Image settings
1. Brightness
2. Contrast
3. Color Space
Auto
4. Detail
Normal
5. 3D Display
6. Video Options
7. Input Levels
8. Picture Settings
Video
9. Save to User
10. DynamicBlack™
11. Image Freeze
12. Advanced Image Settings
Brightness
Adjust the intensity of the image.
Contrast
Adjust the degree of difference between the lightest and darkest parts of the
picture and change the amount of black and white in the image.
Color Space
Select a color space that has been specifically tuned for the input signal.
Useful only for analog signals and certain digital sources.
Detail
Select the edge clarity of the image.
3D Display
Select the 3D relating settings,
• 3D Enable: Set 3D format. Supports Mandatory 3D formats and frame
sequential [email protected]
• 3D Invert: Invert 3D sync signal for the application of using single projector.
• Toggle 3D Blending: Invert 3D sync signal for the application of using
multiple projectors for 3D blending.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-6
Section 4: OPERATION
Video Options
This function is used with video sources only.
• Color: Adjust a video image from black and white to fully saturated color.
The color setting applies to video sources only.
• Tint: Adjust the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.
• Noise Reduction: Reduce temporal or spatial noise in the image.
• Flesh Tone Correction: Control the amount of flesh tone correction applied
to the image.
• Video Black Level: Analyze the current input image and calculate an offset
value which is then added to the analog to digital converter black level
value. This ensures optimum black level for each analog source.
• Detect Film: Control film mode detection and determine whether the
original source of the input video was film or video.
• Closed Captions: Control closed caption display while audio is not muted.
• If this setting is not off, audio is not muted, the source is NTSC and
contains captions on the selected channel, then the projector must display
caption text overlaid on the image.
Input Levels
VGA / Component signals only.
• Adjust the gain of the red, green, or blue channel of the image. It affects the
black and white.
• Adjust the offset of the red, green, or blue channel of the image. It affects
the black and white.
• Sync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connecting to the projector.
Picture Settings
Optimize the projector for displaying images under certain conditions, such as
presentation, video, bright, real, dicom sim, and user-definable preset. It affects
Gamma, Sharpness, White Peaking, Overscan, Brightness, Contrast, Color,
Tint, Red Gain, Green Gain, Blue Gain, Red Offset, Green Offset, Blue Offset.
Save to User
Adjust the image settings and select Save to User as a picture setting. You can
recall these settings in the future by selecting the User in the Picture Settings
menu. The setting of Brightness, Contrast, Color, Tint, Red Gain, Green Gain,
Blue Gain, Red Offset, Green Offset, Blue Offset, Color Temperature, Gamma,
Detail, White Peaking and Overscan can be saved.
4-7
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
DynamicBlack™
Enable or disable the dynamic black function. Enable this function to raise the
contrast ratio dynamically.
Image Freeze
Pause the screen image.
Advanced Image Settings
•
•
•
•
Gamma: Select the appropriate gamma from Video, Film, Bright, CRT, and
DICOM.
White Peaking: (video source only) Increase the brightness of whites that
are near 100%.
Color Temperature: Change the intensity of the colors. Select a listed
relative warmth value.
Edge Enhancement: Apply the edge enhancement process.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-8
Section 4: OPERATION
4.3
Configuration Menu
Configuration
1. Language
English
2. Lens Settings
3. Ceiling Mount
Auto
4. Rear Projection
5. Menu Preferences
6. Power Management
7. High Altitude
8. Communications
9. Backlight Preferences
10. Color Matching
11. Hot-Key Settings
Blank Screen
12. Service
Language
Allow you to select an available language for the OSD display, from English,
French, German, Italian, Spanish, Chinese(simplified), Japanese, Korean, and
Russian.
Lens Settings
•
•
•
•
Focus and Zoom: Adjust the focus and zoom the image in or out.
Lens Shift: Shift the lens up and down or left and right.
Lock all Lens Motors: Select this function to prevent all lens motors from
moving. It may disable the Zoom, Focus, Horizontal and Vertical Position
settings, effectively locking out any changes and overriding all other lens
features. This is particularly useful to prevent accidental lens position
changes in multi-projector installations.
Lens Calibration: Calibrate the lens center.
Ceiling Mount
Turn the image upside down for ceiling-mounted projection.
Rear Projection
Reverse the image so you can project from behind a translucent screen.
4-9
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
Menu Preferences
•
•
•
•
Menu Horz Offset: Change the horizontal position of the OSD.
Menu Vert Offset: Change the vertical position of the OSD.
Show Messages: Display status messages on the screen.
Menu Transparency: Change OSD menu background to be transparent.
NOTE:

•
•
•
As the value increases, more of the image behind the menu is visible.
Splash Screen Setup: Choose which splash screen is to be used.
PIN Protect: The PIN (personal identification number) feature allows you to
password protect your projector. Once you enable the PIN feature, you
must enter the PIN before you can project an image.
Change PIN: Allow you to change the PIN.
Power Management
•
•
•
•
Standby Mode: The projector is in standby mode when connecting to AC
power. (<0.5W)
AC Power On: The projector automatically turns on when electrical power
is connected.
Auto Shutdown: The projector automatically turns off after no signals are
detected for a preset number of minutes. If an active signal is received
before the projector powers down, the image will be displayed.
Sleep Timer: Allow the projector to automatically power off after it has been
on for a specified amount of time (2, 4, or 6 hours).
High Altitude
Set high altitude mode ON/OFF. When it is ON, the fan operates at high speed
to ensure sufficient air flow for high altitudes.
Communications
•
•
Network: Allow you to setup network settings.
- DHCP: Turn the DHCP ON/OFF.
- IP Address: Assign Network IP Address.
- Subnet Mask: Assign Network Subnet Mask.
- Default Gateway: Assign Network Default Gateway.
- Host Name: Display the host name.
- MAC Address: Display network MAC Address value.
- Show Network Messages: Turn network messages ON/OFF.
- Restart Network: Restart the network.
- Network Factory Reset: Perform factory reset on the network settings.
The Projector Name, LAN IP, WLAN IP, and SNMP settings can be
reset.
Serial Port Baud Rate: Select the serial port and baud rate.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-10
Section 4: OPERATION
•
•
•
Serial Port Echo: Control whether the serial port echoes characters.
Serial Port Path: Select the serial port path from either RS232 or HDBaseT.
Projector Address: Set the projector address (0-9). The projector responds
to IR remotes set either at the same address as the projector or to IR
remotes set to address 0.
Backlight Preferences
Control the back light behavior and timeout setting for the keypad and status
LED.
Color Matching
You may require a unique color gamut (range) for a single projector or
application, or you may need to precisely match colors across multiple
adjacent displays. Use Color Matching by Meter Adjustment or by Manual
Adjustment to define the precise hue of each primary color component (red,
green, blue and white).
The x/y coordinates for each color define its location on the standard CIE
chromaticity graph. Changing either or both of these numbers may change the
hue of the color, and modify the range of possible colors. For example,
changing the x/y coordinates for red may move the color closer to orange or
closer to violet, which in turn affects all displayed colors having a red
component. Adjust the slide bars or enter new specific coordinates as desired
to define or change the color gamuts needed for your environment and
applications.
Enable the selected method (Meter or Manual Adjustment)-this automatically
disables the other method. For both methods, if Auto Test Pattern is enabled,
the solid colored test pattern can be displayed according to the menu item on
which you are positioned.
• Meter Adjustment
1 Using a color meter, enter the current x and y co-ordinates of Red,
Green, Blue and White for the projector image into the Measured Data
menu. This is the reference point for the projector. The default values in
the menu are based on the average for all projectors.
2 After measuring the values for all the projectors to be matched,
calculate the target values.
3 Enter the target values for x, y and gain for each color into the Target
Data menu.
4-11
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
Green
Measured
Data
Target Data
Red
Blue
•
Manual Adjustment
1 Adjust color slide bars and judge image color by eye or meter. A userdefined color "adjustment" can be applied.
2 Use this submenu if you do not have specific color coordinates in mind
and will judge color performance by eye or meter. As for Meter
Adjustment, each color control actually defines new x/y coordinates for
that color and changes its hue. The main colors (red part of red, green
part of green and blue part of blue) adjust the intensity of that color
component, while the modifying colors (for example, green part of red
and blue part of red) modify the x and y value and change the hue of
that color. At the same time, the main colors are also used to control the
color of the white point.
Hot-Key Settings
Assign a different function to the hot-key on the remote control by highlighting
the function in the list and pressing ENTER. Choose a function that does not
already have a dedicated button, and assign the hot-key to that function,
allowing you to quickly and easily use the chosen function.
Service
•
•
•
•
Projector Info: Display current projector settings (read-only).
Factory Reset: Restore all settings to their default value. It does not reset
network but it resets RS232.
Test Pattern: Choose the desired internal test pattern to display, or select
OFF to turn off a test pattern.
Color wheel Index (2x): Set Color wheel index to Speed 2X. This setting
only needs to be used when the Main Board is changed, and should be
adjusted to optimize picture quality.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-12
Section 4: OPERATION
•
•
•
•
•
4-13
Color wheel Index (3x): Set Color wheel index to Speed 3X. This setting
only needs to be used when the Main Board is changed, and should be
adjusted to optimize picture quality.
Error log: Show the projector error log for debug.
Mode Adjustment: Fine tune the H and V start position for a signal in the
EDID timing table and record the values in the system to override the timing
table. The settings must be "Saved to Record" before exiting the menu, or
they will be lost. To revert to original timing table settings, each setting must
be manually cleared. Factory Defaults will not clear these override settings.
High temperature warning: Show the warning message when the ambient
temperature is over 35°C.
DA Mode: DA mode helps user to fine tune the DA offset if it is biased
according to serious vibration, heavy dust or improper operation.
1 DA offset
Manually adjust the DA offset to get the correct aperture. User can
change the value of slide bar and observe the projecting image.
Find the value corresponding to the maximum brightness.
Recommended value would be within 10~16.
2 DA calibration
This is the general switch to enable the advanced DA offset calibration.
Enable the advanced algorithm to overcome the DA problems.
3 DA check
Trigger one shot advanced DA offset calibration right away to get the
maximum brightness step.
4 Always calibration
With “DA calibration” being enable, operate the advanced DA offset
calibration automatically in every startup.
This item can be automatically checked if DA failure has ever been
detected.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
4.4
Lamp
Lamp
1. Lamp Mode
Constant Power
2. Constant Power
3. Constant Intensity
4. Current Lamp
Both
5. Lamp Auto Switch
6. Lamp Auto Switch Time
7. Lamp Info
8. Lamp Life Setting
9. Reset Lamp Hours
10. Light Sensor
Lamp Mode
Select Constant Power, Constant Intensity or ECO mode. When in ECO mode,
the projector will adjust to the lowest fan speed and switch the lamp power to
the minimum setting.
Constant Power
Set the value of the lamp power (in Watts).
Constant Intensity
Set the value for the Constant Intensity to maintain constant brightness.
The light sensor monitors the light level and applies more power as the lamp
brightness decays naturally over time. When the lamp setting reaches
maximum power of 465W, it remains at this setting. Note that the light sensor
needs to be calibrated for Constant Intensity mode to work properly. Calibration
should be performed again after every lamp change.
Current Lamp
Select which lamp(s) is in use.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-14
Section 4: OPERATION
NOTE:

A 120 second timed lockout is applied after changing modes before you can change it
again.
Lamp Auto Switch
Control when the projector switches lamps. Options include: on failure only, at
power-up, or after a set number of hours.
Lamp Auto Switch Time
Set the number of hours for Lamp Auto Switch.
For example:
1. Lamp conditions: lamp 1 = 50 hours, lamp 2 = 60 hours.
2. Set the current lamp to lamp 1 - the lamp with the lower lamp hour usage.
3. Set the Lamp Auto Switch to After (N) hours and the Lamp Auto Switch Time
to 100 hours.
4. When lamp 1 reaches 150 hours, projector automatically switches to lamp 2.
5. When lamp 2 reaches 160 hours, projector automatically switches to lamp 1.
Lamp Info
Display current lamp(s) settings (read-only).
Lamp Life Setting
Set the number of hours for the lamp life warning. At every startup, the lamp
hours are checked. If they exceed this value, a lamp replace message
appears.
Reset Lamp Hours
Reset the lamp used hours counter to zero. Do this after changing the lamp.
Light Sensor
Calibrate the Light Sensor for use with the Constant Intensity lamp mode,
which allows the projector to be set for constant brightness. If the Light Sensor
has not been calibrated, Constant Intensity mode may be disabled. Light
Sensor calibration should be repeated when new lamps are installed.
4-15
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
4.5
Status Menu
The read-only Status menu lists a variety of details about the standard and
optional components currently detected in the projector.
For DHD Models
Status
Model Name
D12HD-H
Serial Number
H1YYWWXXX
Native Resolution
1920 x 1080
Firmware
Main Input
V06.00, A06.20, B02.00
Main Signal Format
Main Pixel Clock
74.256MHz
Main Sync Type
Sync on Green
Main Horz Refresh
Main Vert Refresh
45.10kHz
60.0Hz
PIP/POP Input
PIP/PBP Signal Format
PIP/PBP Pixel Clock
PIP/PBP Sync Type
PIP/PBP Horz Refresh
PIP/PBP Vert Refresh
Lamp Power Settings
Current Lamp
Lamp 1 Hours
Lamp 2 Hours
Standby Mode
Lens Lock Settings
Both
0.5W Mode
Allow
IP Address
DHCP
System Temperature
H Series User Manual
020-000772-02 Rev.1 (08-2015)
38°C (No Filter)
4-16
Section 4: OPERATION
For DWU Models
Status
Model Name
D12WU-H
Serial Number
H2YYWWXXX
Native Resolution
1920 x 1200
Firmware
Main Input
V06.00, A06.20, B02.00
Main Signal Format
Main Pixel Clock
74.256MHz
Main Sync Type
Sync on Green
Main Horz Refresh
Main Vert Refresh
45.10kHz
60.0Hz
PIP/POP Input
PIP/PBP Signal Format
PIP/PBP Pixel Clock
PIP/PBP Sync Type
PIP/PBP Horz Refresh
PIP/PBP Vert Refresh
Lamp Power Settings
Current Lamp
Lamp 1 Hours
Lamp 2 Hours
Both
Standby Mode
0.5W Mode
Lens Lock Settings
Allow
IP Address
DHCP
System Temperature
4-17
38°C (No Filter)
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
4.6
Input Switching & PIP Menu
Input Switching & PIP
1. Main Input
VGA
2. PIP/POP Input
Card reader
3. PIP/POP Enable
4. Swap
5. Size
Medium
6. Main Layout
Top Right
7. Timing Detection Mode
8. Source Info
9. Input key
Auto Source
10. Blank on Signal Switch
Main Input
From the list of active inputs, select one to be used as the main image.
PIP/POP Input
From the list of active inputs, select one to be used as the PIP/PBP.
PIP/POP Enable
Toggle between displaying two sources at once (Main and PIP/PBP images) or
one source only. The checkbox turns the PIP/PBP source ON and OFF. Refer
to Section 6.2 for the Main and PIP/PBP compatibility table.
Swap
Change the main image to PIP/PBP, and the PIP/PBP to main image.
Swapping is available only when PIP/PBP is enabled.
Size
Select the PIP/PBP size to small, medium or large.
Main Layout
Set the location of the PIP/PBP image on the screen.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-18
Section 4: OPERATION
NOTE:



PIP/PBP layout and size table as described below.
P : indicates primary source region (lighter color).
* : Both source regions are the same size.
PIP/PBP Size
PIP/PBP Layout
Small
PBP, Bigger Left
Over-Under, Bigger Upper
P
P
PIP-Bottom Right
PIP-Bottom Left
Large
P
P
P
P
PBP, Bigger Right
Over-Under, Bigger Lower
Medium
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
PIP-Top Left
PIP-Top Right
Timing Detection Mode
Select timing detection mode to wide or normal. It is used to support additional
PC timings. When the projected picture is not completed, this function is used
to adjust the picture. "Normal mode" can support all of the 4:3 input sources.
"Wide mode" can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (for
example 1400 x 1050), perform Auto Image using "normal mode".
Source Info
Display current source settings (read-only).
Input key
Use it to list all of the sources or change the sources.
Blank on Signal Switch
When the function is enabled, the projector blanks the screen before timing is
stable when changing source.
4-19
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
4.7
Language Menu
Allow you to select an available language for the OSD display.
Language
4.8
Test Pattern Menu
Choose the desired internal test pattern to display, or select OFF to turn off a
test pattern.
• OFF
• Black
• White
• Checkerboard
• Grid
• Color Bars
Test pattern
1. OFF
2. Grid
3. White
4. Black
5. Checkerboard
6. Color Bars
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-20
Section 4: OPERATION
4.9
Web User Interface
4.9.1
Logging On
Open your web browser and type the IP address (in the address bar) assigned
to your projector.
1 Select the log in level from the Access type list.
2 Enter the Password in the Password field.
3 Select the appropriate language from the Language list.
4 Click the Press login button. The Main window appears.
4.9.2
4-21
Main Tabbed Page - General
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
•
•
•
Control Panel
Select main source / PIP source, enable/disable PIP/PBP, change the
layout / PIP size, swap, and change the test pattern.
Projector Information Panel
Check the projector information for power status, Pic mute status, OSD
status, IP address and Mac address.
Switch Panel
Switch the on/off status of power, Pic mute, and OSD.
4.9.3
Main Tabbed Page - Status
Display the current status of light source, cooling (fans), version numbers and
signal (source) information
4.9.4
Main Tabbed Page - Lens
Control the focus, lens shift and zoom adjustments for the lens.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-22
Section 4: OPERATION
4.9.5
Network
NOTE:

4-23
If you change the setting, the projector’s network subsystem may restart, and you
may be logged off.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
•
•
•
•
Restart Network
Execute a Network restart. This does not change any of the network
settings.
Network Factory Reset
Execute a network factory reset. Network settings may be reset to the
following default values:
- Projector Name = [email protected] + Serial Number
- Show Network Messages = ON
- LAN Settings:
- Manual
- IP Address = 192.168.0.100
- Subnet Mask = 255.255.255.0
- Default Gateway = 192.168.0.100
- WLAN Settings:
- Enabled
- Start IP = 192.168.1.100
- End IP = 192.168.1.120
- Subnet Mask = 255.255.255.0
- Default Gateway = 192.168.1.100
- SNMP Settings:
- SNMP Read Communication = private
- Trap IP Address = 0.0.0.0
- SMTP IP Address = 0.0.0.0
- All other settings are cleared/blanked
- Trap Configuration:
- All items = SNMP Trap + Email
LAN Setting Panel
- Select if the projector must obtain an automatically assigned IP address
through DHCP or if the user set the address manually.
- Enter the IP address, netmask, and default gateway address for the
TCP/IP setting.
WLAN Setting Panel
- Select if the wireless LAN of the projector is enabled or disabled.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-24
Section 4: OPERATION
-
•
•
•
4-25
Enter the IP address range, netmask and default gateway for the
wireless LAN.
SNMP Panel
- The SNMP (Simple Network Management Protocol) interface provides
network administrators with a common way to manage their network
devices from a single remote location. SNMP allows an administrator to
query a number of devices to see their current status/ configuration. It
also allows operators to change configuration values and configure trap
notifications to be sent when certain events occur. (for example, loss of
signal, power state change, and so on)
 Emails are sent to the mail server configured in the projector
settings. Up to two user email accounts can be selected. Any
important information regarding the event is located in the body
content of the email.
 SNMP Traps are notifications that are sent from the projector. They
are only received by a trap receiver (MIB Browser) in the computer.
- SNMP Read Community (default setting: private) - this is a plain - text
password. This must also be entered in the MIB browser. This
password allows the various settings in the projector to be queried.
- SNMP Location (default setting: blank) - This field can be used as a
description to where a projector is located in a building. SNMP emails
sent will specify this location.
- Trap IP Address (default setting: 0.0.0.0) - This field must be filled in to
receive Traps from the projector. The Trap IP Address should be filled in
with the IP Address of the computer on which you would like to view
received traps.
- Trap Email 1/2 (default setting: Blank) - The Trap Email 1 and 2 must be
set to an email address that is configured under the mail server that you
will enter in the "SMTP Server IP Address" field.
- Email from Address (default setting: blank) - the "Email from Address"
that will appear as the source of the SNMP emails.
- SMTP Server IP Address (default setting: 0.0.0.0) - Enter your mail
server's IP address.
Trap Configuration Panel
Set the SNMP actions for the system events. The options are: SNMP Trap
+ Email, Email, SNMP Trap, and Disabled.
Crestron Control System Panel
Enter the IP address, IP ID, and Port of Crestron device for connection.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
4.9.6
Tools
To Use the Tools tabbed pages to control Size & Position, Image Settings,
Configuration, Light Source, Input Switching & PIP and Test Pattern.
4.9.7
Administrator Page
Add or delete a user or change password.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-26
Section 4: OPERATION
4.9.8
•
•
4-27
About Page
Version Tab
View the main firmware version, network firmware version, projector model
name, and projector serial number.
License Tab
The license information of the computer program is displayed.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
4.10
Christie Presenter
The Christie Presenter application allows a remote desktop from a host PC to
be displayed on the network display through Ethernet, USB, or wireless
transports. It can adapt to different network settings (DHCP, fixed IP, and direct
link by USB/Ethernet cable).
Christie Presenter can be downloaded from the Christie website or from the
web page of the projector.
4.10.1 Connect to the Projector
1. Connect to the projector using WiFi or Ethernet
- Ethernet connection:
 Determine the projector's IP address from the menu Main Menu >
Configuration > Communications > LAN.
LAN
1. DHCP
2. IP Address
3. Subnet Mask
4. Default Gateway
5. MAC Address

-
Configure your PC IP address to be on the same network as the
projector.
 The projector and computer must be connected directly or over the
network using Ethernet.
WiFi Wireless connection:
 Insert the WiFi USB dongle (1DWUSB-BGN) into the USB port on
the projector input panel.
Insert the WiFi USB dongle
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-28
Section 4: OPERATION



Power on the Projector.
Obtain the WiFi SSID from the OSD menu Main Menu >
Configuration > Communications > WLAN.
Connect your PC device to the wireless SSID for the selected
projector . Example: "[email protected]".
4.10.2 Install Christie Presenter software
1. Use a web browser to connect to the projector's network address (Default
address 192.168.1.100).
2. Download and install the Christie Presenter Software.
4-29
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
3. Configure the Christie Presenter Software. The name entered is used to
identify all computers connected to the projector by the Christie Presenter
software/either wired or wireless connections. The Network Display Management -> Device Management tab shows all current connections.
4.10.3 Use Christie Presenter
1. Press the autorun icon in the system tray to pause or play the USB display.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-30
Section 4: OPERATION
2. After starting the Christie Presenter application, the main window can been
seen (shown below).
Icon
Description
Connect and search network display.
Stop/start displaying desktop contents to
connected network display.
Select display region.
Configure Christie Presenter.
Manage all connected network displays.
Disconnect all connections.
Connect and search network display
1
4-31
Click the button
to enter into the connection menu section.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
2
If the IP address of the projector is known, type the IP address and click
the "Connect" button. If the IP address is not known, click the "Search"
button to search for the projector on the network and select the
projector to which you want to connect. Select the option "Directly" in
order to proceed to the log in interface.
3
Input "User type" and "Password" in the log-in interface. Select the
display port (the default is full screen). Obtain the " Normal " user's
password from the OSD menu Main Menu > Configuration >
Communications > WLAN.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-32
Section 4: OPERATION
Select display region
Once the connection is set up, click the button
to select the size of
the projection region: FullScreen, FixedSize, or Alterable.
•
•
•
4-33
FullScreen: The default capture mode turns to Full screen when the
program is launched. At that time, if screen capture starts, the image of the
whole screen is transferred to a remote network display.
FixedSize: Users can place a frame on the desktop. Only the image
enclosed inside the frame is transferred to remote network display.
Alterable: Only region captured is the one enclosed by the frame. The
region can be enlarged or downsized by dragging the eight small black
squares scattered on eight edges of the frame.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
Configure Christie Presenter
Click the button
to configure Christie Presenter for Basic Setting and
Advanced Setting.
•
•
Basic Setting: Select language, change the region size of fixed size capture
mode, and select if notification message popup is allowed.
Advanced Setting: Select the quality of JPEG image, YUV sample format
and network port setting. (The "Fixed" port is Port 5900.)
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-34
Section 4: OPERATION
Manage all connected network displays
Click the button
to control all the users and all the projectors
connector to the same projector.
Icon
Description
Administrator log in.
Normal user log in.
Device is connected.
Device is not connected.
The icon shows the current status and display
position of the local screen on the network
display. Click the icon to change the display
position. A dialog appears.
Click this unlock icon to change the password.
(Password change to target network display. Only
an Administrator user can change the password.)
No response is expected when this icon is
clicked. If user log in as "Admin", the key icon can
be seen and the Presenter password can be
changed. If user log in as "Normal", the lock icon
can be seen and the Presenter password cannot
be changed.
Disconnect from target network display.
Link for connecting to a target network display via
a webpage.
4-35
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
4.11
Card Reader Operation
Four operation modes are available in the Card Reader application:
- USB Flash Devices Detection Screen
- Thumbnail Display Mode
- Images Display Mode
- Images Slide Show Mode
1. USB Flash Device Detection Screen:
In this mode, the Card Reader application detects any USB flash devices
hot-plug events and displays the flash device icon. When the flash device is
removed from USB, the icon disappears. We recommend that USB flash
devices should be removed only when the Card Reader is changed to the
USB Flash Devices Detection Screen state.
2. Thumbnail Display Mode:
Press the Enter key to enter the Thumbnail Display Mode. Different photos
in different folders can be chosen. Press the Menu key to bring up the Card
Reader operation UI.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-36
Section 4: OPERATION
The user interface is designed to operate the card reader application with a
few keys (Enter/Left/Right/Up/Down).
The following buttons are supported in the user interface:
•
Previous: Move the selected item left. (Go to previous page when this
is the leftmost item.)
•
Next: Move the selected item right. (Go to next page when this is the
rightmost item.)
•
Display: Display the selected image or display the selected folder.
•
Thumbnail: Enter the Thumbnail Display Mode.
•
SlideShow: Enter the Slide Show Mode.
•
NameOrder: Sort files/folders in name order.
•
ExtendOrder: Sort files/folders in extended order.
•
SizeOrder: Sort files/folders in size order.
•
TimeOrder: Sort files/folders in time order.
•
EXIF ON/OFF: Enable/Disable auto image rotate accordingly to EXIF
information.
•
FileName ON/OFF: Enable/Disable filename display in Thumbnail
Display Mode.
3. Image Display Mode:
Press the ENTER key in the Thumbnail Display Mode to enter the Image
Display Mode; press the SlideShow key to enter the Slide Show Mode. The
Left/Right key is used to display the last/next image in the Image Display
Mode. In the Image Display Mode, press the ENTER key to quit from the
Image Display Mode and enter the Thumbnail Display Mode.
In the Slide Show Mode, press the ENTER key to enter the Image Display
Mode.
The alternative way to display image in the Image Display Mode or Slide
Show Mode is using the operation UI.
4-37
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
The following operations are supported in the operation UI.
•
Display: Enter the Image Display Mode.
•
Thumbnail: Enter the Thumbnail Display Mode.
•
SlideShow: Enter the Slide Show Mode.
•
Actual Size: Display in actual size of the image.
•
Best Fit: Display the image in best fit to the screen.
•
EXIFDisp OFF/On: Enable/Disable EXIF information display.
•
+90deg: Rotate 90 degree.
•
-90deg: Rotate -90 degree.
4. Image Slide Show Mode:
The following operations are supported in the Slide Show Mode operation
UI.
•
Stop: Stop Slide Show Mode.
•
Next: Display next image.
•
Previous: Display previous image.
•
Delay 3/4/5: Slide Show delay in seconds.
•
Slide Effect: Following modes are supported.
- Slide Right
- Blocks
- RightDown
- XLines
- Slide Up
- Ylines
- Repeat ON/OFF: Enable/Disable Slide Show Repeat Mode.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-38
Section 4: OPERATION
When the image cannot be displayed due to memory limitation or cannot
support image format, the specific image is displayed on the center of the
screen.
4-39
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 4: OPERATION
H Series User Manual
020-000772-02 Rev.1 (08-2015)
4-40
Section 5: TROUBLESHOOTING
5.
TROUBLESHOOTING
If you cannot resolve an issue using the information provided in this section,
contact your reseller or service center.
Problem
-
•
Solution
No image appears on-screen
Make sure all the cables and power connections are
correctly and securely connected See "INSTALLATION".
-
Check if the Lamp Status LED is in Green.
-
Make sure you have removed the lens cap and the
projector is switched ON.
Partial, scrolling or incorrectly
displayed image
Press "AUTO" on control panel or on remote control.
If using a PC (for Windows 95, 98, 2000, XP, Windows 7):
1. Click the "My Computer" > "Control Panel" and then
double-click "Display".
2. Select the "Settings" tab.
3. Verify that your display resolution setting is lower than
or equal to WUXGA (1920 × 1200).
4. Click on the "Advanced Properties" button. If the
projector is still not projecting the whole image, change
the monitor display:
4.1 Verify the resolution setting is lower than or equal to
WUXGA (1920 × 1200).
4.2 Select the "Change" button under the "Monitor" tab.
4.3 Click on "Show all devices". Next, select "Standard
monitor types" under the SP box; choose the
resolution mode you need under the "Models" box.
4.4 Verify that the resolution setting of the monitor
display is lower than or equal to WUXGA (1920 ×
1200).
5-1
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 5: TROUBLESHOOTING
Problem
-
Solution
Partial, scrolling or incorrectly
displayed image
If using a Notebook:
1. Adjust resolution of the computer.
2. Press the keys listed below for your notebook
manufacturer to send signal out from notebook to
projector. Example: [Fn]+[F4]
Notebook Brand
Function Keys
Acer
[Fn]+[F5]
Asus
[Fn]+[F8]
Dell
[Fn]+[F8]
Gateway
[Fn]+[F4]
IBM/Lenovo
[Fn]+[F7]
HP/Compaq
[Fn]+[F4]
NEC
[Fn]+[F3]
Toshiba
[Fn]+[F5]
Mac Apple
System Preference  Display 
Arrangement  Mirror display
-
If you experience difficulty changing resolutions or your
monitor freezes, restart all equipment including the
projector.
•
The screen of the
Notebook or
PowerBook
computer is not
displaying your
presentation
-
If using a Notebook PC
Some Notebook PCs may deactivate their own screens
when a second display device is in use. Each has a
different method of reactivation. Refer to your computer
manual for detailed information.
•
Image is unstable
or flickering
-
Use "Pixel Track" and "Pixel Phase" to correct it.
-
Change the monitor color setting on your computer.
•
Image has vertical flickering bar
-
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Use "Auto Image" to make an adjustment.
Check and reconfigure the display mode of your graphic
card to make it compatible with the projector.
5-2
Section 5: TROUBLESHOOTING
Problem
•
•
•
5-3
Image is out of
focus
The image is
stretched when
displaying 16:9
DVD title
Solution
-
Make sure both lens caps (front and back) are removed.
-
Adjust lens focus to fit.
-
Make sure the projection screen is between the required
distance.
-
When you play anamorphic DVD or 16:9 DVD, the projector
shows the best image if the projector display mode is set to
16:9 in the OSD.
-
If you play 4:3 format DVD titles, change the format to 4:3 in
the projector OSD.
-
If the image is still stretched, you must also adjust the
aspect ratio by setting the display format as 16:9 (wide)
aspect ratio type on your DVD player.
Image is too small or too large
-
Adjust lens zoom to fit.
If the image does not fill the screen properly, verify that the
correct lens is in use or change the position of the projector.
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 5: TROUBLESHOOTING
H Series User Manual
020-000772-02 Rev.1 (08-2015)
5-4
Section 6: SPECIFICATIONS
6.
SPECIFICATIONS
6.1
Inputs
Signal
Type
Resolution
Frame Rate
(Hz)
640x350
85
640x400
85
640x480
59
640x480
60
●
640x480
72
640x480
75
640x480
VGA
HDMI ½
DVI
Display port
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
85
●
●
●
●
●
●
720x400
60
●
●
●
●
●
●
720x400
85
●
●
768x480
60
●
●
●
●
768x480
75
●
●
●
●
768x480
85
●
●
●
●
800x600
50
●
●
●
●
800x600
56
●
●
●
●
●
●
800x600
60
●
●
●
●
●
●
800x600
72
●
●
●
●
●
●
800x600
75
●
●
●
●
●
●
800x600
85
●
●
●
●
●
●
800x600
120
●
●
848x480
50
●
●
●
●
848x480
60
●
●
●
●
848x480
75
●
●
●
●
848x480
85
●
●
●
●
960x600
50
●
●
●
●
960x600
60
●
●
●
●
960x600
75
●
●
●
●
●
BNC
●
3G-SDI
HDBaseT
CVBS
PC
●
●
NOTE:

6-1
"RB" means "reduced blanking".
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 6: SPECIFICATIONS
Signal
Type
Resolution
Frame Rate
(Hz)
960x600
85
1024x768
60
●
1024x768
75
1024x768
PC
HDMI ½
DVI
Display
port
●
●
●
●
●
●
85
●
●
1024x768
120
●
1064x600
HDBaseT
CVBS
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
50
●
●
●
●
1064x600
60
●
●
●
●
1064x600
75
●
●
●
●
1064x600
85
●
●
●
●
1152x720
50
●
●
●
●
1152x720
60
●
●
●
●
1152x720
75
●
●
●
●
1152x720
85
●
●
●
●
1152x864
60
●
●
●
●
●
●
1152x864
70
●
●
●
●
●
●
1152x864
75
●
●
●
●
●
●
1152x864
85
●
●
●
●
●
●
1224x768
50
●
●
●
●
1224x768
60
●
●
●
●
1224x768
85
●
●
●
●
1280x720
50
●
●
●
●
1280x720
60
●
●
●
●
●
●
1280x720
75
●
●
●
●
●
●
1280x720
85
●
●
●
●
●
●
1280x720
120
●
●
●
1280x768
60
●
●
●
●
●
●
1280x768
75
●
●
●
●
●
●
H Series User Manual
020-000772-02 Rev.1 (08-2015)
VGA
BNC
3G-SDI
●
●
6-2
Section 6: SPECIFICATIONS
Signal
Type
Resolution
Frame Rate
(Hz)
VGA
BNC
HDMI ½
DVI
Display
port
1280x768
85
●
●
●
●
●
●
1280x800
50
●
●
●
●
●
●
1280x800
60
●
●
●
●
●
●
1280x800
75
●
●
●
●
●
●
1280x800
85
●
●
●
●
●
●
1280x960
50
●
●
●
●
1280x960
60
●
●
●
●
●
●
1280x960
75
●
●
●
●
●
●
1280x960
85
●
●
●
●
●
●
1280x1024
50
●
●
●
●
1280x1024
60
●
●
●
●
●
●
1280x1024
75
●
●
●
●
●
●
1280x1024
85
●
●
●
●
●
●
1356x960
50
●
1356x960
60
●
1356x960
75
●
1356x960
85
●
1360x768
50
●
●
●
●
1360x768
60
●
●
●
●
1360x768
75
●
●
●
●
1360x768
85
●
●
●
●
1366x768
60
●
●
●
●
●
●
1400x900
60
●
●
1400x1050
50
1400x1050
60
●
1400x1050
75
1440x900
60
1440x900
75
3G-SDI
HDBaseT
CVBS
PC
6-3
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 6: SPECIFICATIONS
Signal
Type
Resolution
Frame Rate
(Hz)
HDMI ½
DVI
Display
port
1600x900
60
●
●
●
●
1600x1200
50
●
●
●
●
1600x1200
60
●
●
●
●
1680x1050
50
●
●
●
●
1680x1050
60
●
●
●
●
1680x1050
75
1704x960
50
●
●
●
●
1704x960
60
●
●
●
●
1704x960
75
●
1704x960
85
●
1728x1080
50
●
●
●
●
1728x1080
60
●
●
●
●
1864x1050
50
●
●
●
●
1864x1050
60
●
●
●
●
1864x1050
75
1920X1080
50
1920X1080
60
●
1920X1200RB
60
1920X1200RB
50
2128x1200
60
NTSC (M, 4.43)
60
●
PAL (B,G,H,I)
50
●
PAL (N)
50
●
PAL (M)
60
●
SECAM (M)
50
●
480i
60
●
●
●
●
●
●
576i
50
●
●
●
●
●
●
VGA
●
●
BNC
●
●
3G-SDI
HDBaseT
CVBS
●
PC
NTSC
PAL
SECAM
H Series User Manual
020-000772-02 Rev.1 (08-2015)
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
6-4
Section 6: SPECIFICATIONS
Signal
Type
Resolution
Frame Rate
(Hz)
VGA
BNC
HDMI ½
DVI
Display
port
480p
60
●
●
●
●
●
●
576p
50
●
●
●
●
●
●
1080i
25
●
●
●
●
1080i
29
●
●
●
●
●
●
1080i
30
●
●
●
●
●
●
720p
50
●
●
●
●
●
●
720p
59
●
●
●
●
●
●
720p
60
●
●
●
●
●
●
1080s
23
●
1080s
24
●
1080p
23
●
●
●
●
●
●
1080p
24
●
●
●
●
●
●
1080p
25
●
●
●
●
●
●
1080p
29
●
●
●
●
●
●
1080p
30
●
●
●
●
●
●
1080p
50
●
●
●
●
●
●
1080p
59
●
●
●
●
●
●
1080p
60
●
●
●
●
●
●
Frame Packing
1080p
24
●
●
Frame Packing
720p
50
●
●
Frame Packing
720p
60
●
●
Side by Side 1080i
50
●
●
Side by Side 1080i
60
●
●
Top and Bottom
720p
50
●
●
Top and Bottom
720p
60
●
●
Top and Bottom
1080p
24
●
●
3G-SDI
HDBaseT
CVBS
EDTV
●
HDTV
Mandatory
3D
6-5
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 6: SPECIFICATIONS
Signal
Type
Resolution
Frame Rate
(Hz)
800x600
120
●
●
1024x768
120
●
●
1280x720
120
●
●
480i YcbCr422
10bit
59.94
●
576i YcbCr422
10bit
50
●
50
●
59.94
●
60
●
50
●
59.94
●
60
●
23.98
●
24
●
25
●
29.97
●
30
●
25
●
29.97
●
30
●
50
●
59.94
●
60
●
50
●
59.94
●
60
●
Frame
sequential
3D
VGA
BNC
HDMI ½
DVI
Display
port
3G-SDI
HDBaseT
CVBS
SD-SDI
720p YcbCr422
10bit
1080i YcbCr422
10bit
HD-SDI
1080p YcbCr422
10bit
1080sF YcbCr422
10bit
3GA-SDI
3GB-SDI
1080p YcbCr422
10bit
1080p YcbCr422
10bit
With 352M Payload
ID
H Series User Manual
020-000772-02 Rev.1 (08-2015)
6-6
Section 6: SPECIFICATIONS
6.2
PIP/POP Compatibility
PIP/POP
3G-SDI
VGA
BNC
DVI
CVBS
Display
Port
HDMI1
HDMI2
HDBase
T RJ45-1
USB A
Mini USB
RJ45-2
3G-SDI
-
-
-
-
●
●
●
●
●
●
●
●
VGA
-
-
-
-
●
●
●
●
●
●
●
●
BNC
-
-
-
-
●
●
●
●
●
●
●
●
DVI
-
-
-
-
●
●
●
●
●
●
●
●
CVBS
●
●
●
●
-
-
-
-
-
-
-
Display Port
●
●
●
●
-
-
-
-
-
-
-
HDMI1
●
●
●
●
-
-
-
-
-
-
-
HDMI2
●
●
●
●
-
-
-
-
-
-
-
HDBaseT
RJ45-1
●
●
●
●
-
-
-
-
-
-
-
USB A
●
●
●
●
-
-
-
-
-
-
-
Mini USB
●
●
●
●
-
-
-
-
-
-
-
RJ45-2
●
●
●
●
-
-
-
-
-
-
-
Matrix
● : PIP/POP combinations are enabled
- : PIP/POP combinations are disabled
6-7
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 6: SPECIFICATIONS
6.3
Key Features
•
•
HD 0.95" 1920 × 1080 resolution or WUXGA 0.96" 1920 × 1200 resolution
Projection lens compatibility:
- Horizontal offset ranges: +/-50%
- Vertical offset ranges: +/-120% (WUXGA) and +/-140% (HD)
NOTE:

Measurements are based on industry standards where offset is calculated as a ratio
of the number of pixels shifted up/ down to half the image size.
-
360 degree orientation
Optional color wheel for rich color performance
3D blending & auto warping for different application
Support dust / fog filter to make projector get a better life time.
NOTE:

•
•
•
•
•
•
6.4
Dust filter will be standard accessory.
Fog filter will be optional parts.
Wireless desktop display using wireless dongle (optional)
SNMP traps and email notifications
10-bit image processor electronics with modular design
All video formats can be resized to full screen either horizontally or
vertically while maintaining aspect ratio
The projector can be operated using any of the following:
- The built-in keypad, an infrared (IR) remote control, a wired remote
control, a PC/device using serial communications (Ethernet or RS232)
- A Web page via Ethernet or from a PC/device via a wireless USB
dongle (Optional)
Built-In keypad
List of Components
This projector comes with all the items listed below. Check to make sure your
package is complete. Contact your dealer if anything is missing.
•
•
•
•
•
IR remote control 003-004468-01
Power cord x 4
- UK/Korea/Russia
- North America
- Europe
- Japan
User manual (CD)
Fuse (15A fuse installed in the projector)
Dust Filter x 3 (It will be applied in the environment which got serious dust.)
H Series User Manual
020-000772-02 Rev.1 (08-2015)
6-8
Section 6: SPECIFICATIONS
NOTE:

6.5
Optional Accessories
•
•
•
•
•
•
•
•
6.6
Due to the difference in applications for each country, some regions may have different
accessories.
Standard Lens (A21-TR 1.5-2.0) (140-110103-01)
Optional Lens (A20-TR 1.2-1.5) (140-109101-01)
Optional Lens (A22-TR 2.0-4.0) (140-111104-01)
Optional Lens (A18-TR 0.84-1.02) (140-114107-01)
Optional Lens (A19-TR 1.02-1.36) (140-115108-01)
1DWUSB-BGN / Wireless dongle (optional accessory) (133-113106-01)
Lens adapter (140-112105-01)
Optional Color Wheel
REGULATORY
•
•
Safety
- CSA C22.2 No. 60950-1
- UL 60950-1
- IEC 60950-1
- EN 60950-1
Electro-Magnetic Compatibility
Emissions
-
FCC CFR47, Part 15, Subpart B/ANSI C63.4, Class A - Unintentional
Radiators
CISPR 22/EN55022 Class A - Information Technology Equipment
ICES/NMB003 (A) - Information Technology Equipment
Immunity
-
•
•
6-9
CISPR 24/EN55024 EMC Requirements - Information Technology
Equipment
Environmental
The product conforms to:
- EU Directive (2011/65/EU) on the restriction of the use of certain
hazardous substances (RoHS) in electrical and electronic equipment
and the applicable official amendment(s).
- EU Regulation (EC) No. 1907/2006 on the registration, evaluation,
authorization and restriction of chemicals (REACH) and the applicable
official amendment(s).
- EU Directive (2012/19/EU) on waste and electrical and electronic
equipment (WEEE) and the applicable official amendment(s).
- China Ministry of Information Industry Order No.39 (02/2006) on the
control of pollution caused by electronic information products, the
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 6: SPECIFICATIONS
•
6.7
hazardous substances concentration limits (SJ/T11363-2006), and the
applicable product marking requirement (SJ/T11364-2006).
Marking
- This product conforms to all relevant Canadian, US, and European
directives, standards, safety, health and environmental concerns.
International packaging recycling marks conform to:
 EU Directive (2012/19/EU) on waste and electrical and electronic
equipment (WEEE) .
 EU Directive (94/62/EC) on packaging and packaging waste
 China packaging recycling mark standard (GB18455-2001)
Federal Communications Commission (FCC) Warning
WARNING
A shielded-type power cord is required to meet FCC emission limits and
also to prevent interference to the nearby radio and television reception.
Only the supplied power cord must be used.
• Use only shielded signal cables to connect I/O devices to this equipment.
•
H Series User Manual
020-000772-02 Rev.1 (08-2015)
6-10
Section 6: SPECIFICATIONS
6.8
OSD Tree
Level 1
Level 2
Level 3(Or List)
Level 4(Or List)
Level 5(Or List)
Level 6(Or List)
Default
Auto
Native
4:3
Letterbox
Size Presets
Auto
Full Size
Full Width
Full Height
Custom
3D Mode
Off
Overscan
Zoom
By source set
Crop
Size & Position
Pixel Track
0 - 100
50
Pixel Phase
0 - 100
50
Horz Position
0 - 100
50
Vert Position
0 - 100
50
Digital Horz Zoom
50%~400%
100
Digital Vert Zoom
50%~400%
100
Digital Horz Shift
0 - 100
50
Digital Vert Shift
0 - 100
50
PC Mode
On
Keystone
Geometry Correction
Warp
Pincushion
Reset
Horz Keystone
-20 ~ +20
0
Vert Keystone
-20 ~ +20
0
Horz Pincushion
-50 ~ +50
0
Vert Pincushion
-50 ~ +50
0
command
Auto Image
command
Brightness
0 - 100
50
Contrast
0 - 100
By source set
Auto
Auto
RGB
Color Space
RGB
RGB Video
RGB
REC709
YUV
REC709
REC601
REC709
Maximum
High
Image settings
Detail
Normal
By source set
Low
Minimum
Auto
Frame PackingSide by Side
3D Enable
3D Display
Top and Bottom
Auto
Feame Sequential
Off
6-11
3D Invert
Off/On
Toggle 3D Blending
command
Off
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 6: SPECIFICATIONS
Level 1
Level 2
Video Options
Level 3(Or List)
Level 4(Or List)
Color
0 - 100
Level 5(Or List)
Level 6(Or List)
Default
50
Tint
0 - 100
50
Noise Reduction
0 - 100
0
Flesh Tone Correction
0 - 100
0
Off/On
Off
Video Black Level
Detect Film
Off
Closed captions
cc1
Off
cc2
Input Levels
Red Gain
0 - 100
50
Green Gain
0 - 100
50
Blue Gain
0 - 100
50
Red Offset
0 - 100
50
Green Offset
0 - 100
50
Blue Offset
0 - 100
50
Sync Threshold
0 - 100
50
Reset RGB Gain/
Offset
command
Presentation
Video
Bright
Picture Settings
Real
By source set
DICOM SIM
2D High Speed
Image settings
3D
User
Save to User
command
DynamicBlack™
Off / On
Image Freeze
Off / On
Off
Off
Video
Film
Gamma
Bright
By source set
CRT
DICOM
BrilliantColor™
White Peaking
Normal Look
Bright Look
0 - 100
Bright Look
By source set
Warmest
Advanced Image
Settings
Color Temperature
Warm
Cool
By source set
Bright
Off
Edge Enhancement
Normal
Off
Maximum
Color Wheel
Speed
2X
3X
2X
Off
Color Enhancement
CE 1
CE 1
CE 2
H Series User Manual
020-000772-02 Rev.1 (08-2015)
6-12
Section 6: SPECIFICATIONS
Level 1
Level 2
Level 3(Or List)
Level 4(Or List)
Level 5(Or List)
Language
Default
English
Focus
command
Zoom
command
Lens Shift
Lens Settings
Level 6(Or List)
command
Apply Position
1-5
Lens Memory
Save Current
Position
1-5
Lock all Lens
Motors
Allow
Locked
Lens calibration
command
Ceiling Mount
Off/On/Auto
Rear Projection
Off/On
Allow
Auto
Off
Menu Horz Offset
0 - 100
0
Menu Vert Offset
0 - 100
0
Show Messages
Off/On
Menu Transparency
0 - 90
0
Factory Logo
Menu Preferences
Splash Screen
Setup
Blue
Black
Factory Logo
White
PIN Protect
command
Change PIN
command
Standby Mode
Communication
mode
AC Power On
Off/On
0.5 W Mode
Communication
mode
Off
Never
5 Mins
Configuration
10 Mins
Power Management
Auto Shutdown
15 Mins
Never
20 Mins
25 Mins
30 Mins
Off
Sleep Timer
2 Hrs
4 Hrs
Off
6 Hrs
High Altitude
Off/On
Off
DHCP
IP Address
LAN
Subnet Mask
by set
Default Gateway
MAC Address
Enable
by set
Start IP
End IP
Communications
WLAN
Subnet Mask
Default Gateway
MAC Address
SSID
Projector Name
Network
Show Network
Messages
Restart Network…
by set
Network Factory
Reset...
6-13
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 6: SPECIFICATIONS
Level 1
Level 2
Level 3(Or List)
Level 4(Or List)
Level 5(Or List)
Level 6(Or List)
Default
2400
4800
9600
14400
Serial Port Baud
Rate
115200
19200
38400
Communications
57600
115200
1200
Serial Port Echo
Serial Port Path
Projector Address
Off/On
Off
RS232
RS232
HDBaseT
0-9
0
Timeout 5 Secs
Timeout 10 Secs
Keypad Backlight
Backlight Preferences
Timeout 20 Secs
Timeout 5 Secs
Timeout 30 Secs
Always On
Always Off
Always On
Status LED
Always Off
Always On
Warnings/Errors
Only
Enable
On/Off
Off
Auto Test Pattern
On/Off
On
Configuration
Measured Data
Color Matching
Meter Adjustment
Target Data
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Intensity of Red
100 - 10000
453
x of Red
0.300 - 0.700
0.633
0.356
y of Red
0.300 - 0.500
Intensity of Green
100 - 10000
2137
x of Green
0.300 - 0.400
0.352
0.572
y of Green
0.400 - 0.700
Intensity of Blue
100 - 10000
239
x of Blue
0.100 - 0.300
0.140
0.093
y of Blue
0.030 - 0.400
Intensity of White
100 - 10000
9219
x of White
0.200 - 0.400
0.331
0.380
y of White
0.200 - 0.400
Reset to Default
Yes/No
Gain of Red
0.200 - 1.000
1.000
x of Red
0.300 - 0.700
0.643
y of Red
0.300 - 0.500
0.344
Gain of Green
0.200 - 1.000
1.000
x of Green
0.300 - 0.400
0.329
y of Green
0.400 - 0.700
0.544
Gain of Blue
0.200 - 1.000
1.000
x of Blue
0.100 - 0.300
0.141
y of Blue
0.030 - 0.400
0.094
Gain of White
0.200 - 1.000
1.000
x of White
0.200 - 0.400
0.334
y of White
0.200 - 0.400
0.371
Reset to Default
Yes/No
Enable
On/Off
Off
Auto Test Pattern
On/Off
On
1000
Red Part of Red
0 - 1000
Green Part of Red
0 - 1000
0
Blue Part of Red
0 - 1000
0
6-14
Section 6: SPECIFICATIONS
Level 1
Level 2
Color Matching
Level 3(Or List)
Manual Adjustment
Level 4(Or List)
Level 5(Or List)
Green Part of
Green
0 - 1000
Level 6(Or List)
Default
1000
Red Part of
Green
0 - 1000
0
Blue Part of
Green
0 - 1000
0
Blue Part of Blue
0 - 1000
1000
Red Part of Blue
0 - 1000
0
Green Part of Blue
0 - 1000
0
Red Part of White
0 - 1000
1000
Green Part of
White
0 - 1000
1000
Blue Part of White
0 - 1000
1000
Reset to Default
Yes/No
Blank Screen
Aspect Ratio
Hot-Key Settings
Freeze Screen
Projector Info
Overscan
Closed Captions
Model Name
Serial Number
Native Resolution
Firmware
Projector Info
Configuration
Boot Code
Standby Mode
Lens Lock Settings
Configuration
Color wheel Index
Factory Reset…
command
Off
Grid
White
Black
Checkerboard
Color Bars
Service
Test Pattern
Red
Green
Blue
Yellow
Magenta
Cyan
Boresight
Color wheel Index
(2x)
Color wheel Index
(3x)
Error log
Show log
Clear log
Mode Adjustment
DA Offset
DA mode
DA Calibration
DA Check
Always Calibration
6-15
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Section 6: SPECIFICATIONS
Level 1
Level 2
Level 3(Or List)
Lamp Mode
Constant Power/
Constant Intensity/ECO mode
Level 4(Or List)
Level 5(Or List)
Level 6(Or List)
Default
Constant Power
Constant Power
0 - 10
10
Constant Intensity
0 - 10
7
Lamp 1
Current Lamp
Lamp 2
Both
Both
On Failure Only
Lamp Auto Switch
At Power-Up
On Failure Only
After X Hours
Lamp
Lamp Auto Switch
Time (Hours)
5 - 3000
100
Lamp 1 Hours
Lamp 2 Hours
Lamp Info
Total Projector
Hours
Lamp 1 Reset
Lamp 2 Reset
Lamp Life Setting
xxxxx
Reset Lamp Hours
command
2000 hrs
Light Sensor
Light Sensor Calibration
command
Calibrated?
(display Yes/No)
Model Name
Serial Number
Native Resolution
Firmware
Vxx, Ayy, Bzz
Main Input
Main Signal Format
Main Pixel Clock
Main Sync Type
Main Horz Refresh
Main Vert Refresh
PIP/PBP Input
PIP/PBP Signal
Format
PIP/PBP Pixel
Clock
PIP/PBP Sync
Type
Status
PIP/PBP Horz
Refresh
PIP/PBP Vert
Refresh
Lamp Power Settings
Current Lamp
Lamp 1 Hours
Lamp 2 Hours
Standby Mode
Lens Lock Settings
IP Address
DHCP
System Temperature
H Series User Manual
020-000772-02 Rev.1 (08-2015)
6-16
Section 6: SPECIFICATIONS
Level 1
Level 2
Level 3(Or List)
Main Input
SPEC define
PIP/PBP Input
SPEC define
PIP/PBP Enable
Level 4(Or List)
OFF
Level 5(Or List)
Level 6(Or List)
Default
OFF
ON
Swap
Size
(Small/Medium/
Large)
Main Layout
(PBP, Main Left /
PBP, Main Top /
PBP, Main Right /
PBP, Main Bottom / PIP-Bottom
Right / PIP-Bottom Left / PIP-Top
Left / PIP-Top
Right)
Timing Detection
Mode
Normal
Wide
Wide
Active Source
Input Switching & PIP
Signal Format
Aspect Ratio
Resolution
Vert Refresh
Horz Refresh
Source Info
Pixel Clock
Sync Type
Color Space
PIP/PBP
(When PIP/PBP
active)
<PIP/PBP source
lines>
(When PIP/PBP
active)
Change Sources
Input key
List all Sources
Auto Source
Auto Source
Blank on Signal
Switch
Language
OFF
ON
OFF
English
Off
Grid
Test Pattern
White
Black
Checkerboard
Color Bars
6-17
H Series User Manual
020-000772-02 Rev.1 (08-2015)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement