AEM 30-2710 Peak & Hold Injector Driver 10 Channel Instructions

Installation Instructions

10 Ch Peak & Hold Injector Driver

PN 30-2710

WARNING:

This installation is not for the electrically challenged! Use this product with extreme caution! If you are uncomfortable with anything about this, please refer the installation to an AEM trained tuning shop or call

,

!

800-423-0046 for technical assistance. You should also visit the AEM

Performance Electronics Forum at http://forum.aempower.com

NOTE: AEM holds no responsibility for any engine damage that results from the misuse of this product!

This product is legal in California for racing vehicles only and should never be used on public highways.

ADVANCED ENGINE MANAGEMENT INC.

2205 126th Street Unit A, Hawthorne, CA. 90250

Phone: (310) 484-2322

Fax: (310) 484-0152 http://www.aempower.com

Instruction Part Number: 10-2710

2003-2007 Advanced Engine Management, Inc.

IMPORTANT!

Read these instructions completely before attempting this installation!

The AEM 10 Channel Peak & Hold Injector drivers contains 10 independent injector drive channels. It’s typical function is to allow full battery voltage to fuel injectors for rapid current rise, in order to produce positive injector opening. When load current reaches 4.1A, the injector driver reduces the load current to 1.1A and operates as a constant current sink. This condition holds the injector open and reduces system power dissipation. If the current fails to reach 4.1A within 5mS, the driver module automatically limits the load current to 1.1A.

NOTE: It is strongly recommended that you have a wiring diagram for your specific vehicle before attempting to install the AEM P&H driver module.

TECHNICAL FEATURES

Operating Voltage:

RPM Capability:

Injector Triggers:

8-18 volts, negative ground

Unlimited

Trigger Waveform:

Trigger Impedance:

Injector Outputs:

Output Current High:

10

Output is activated when trigger is grounded

220 Ohm input impedance, pulled to 12V (60 mA draw)

10

4.15A Peak, Typical

Output Current Low: 1.15A Sustain, Typical

Peak Current Timeout: 5mS

Size: 5.5"L x 4.6"W x 1.4"H

Weight:

Over Temp Shutdown:

2.7 Lbs

115C (Nominal)

BATTERY

The AEM P&H Driver is designed for negative ground, 12 volt and 16 volt electrical systems.

WELDING

Before welding on your vehicle, disconnect the AEM P&H Driver power cables from the battery. Failure to do so may damage it.

MOUNTING

The AEM P&H Driver may be mounted in any position as long as it is not in an enclosed location nor near a large heat source. It may not be mounted directly to the engine nor should it be mounted near or above the exhaust manifold(s).

WIRING

GENERAL WIRING RECOMMENDATIONS

•

Solder wire joints for the most trouble-free connections.

•

Always run wires away from direct heat and sharp edges.

•

A poor ground connection is the leading cause of ignition problems.

•

Connect ground wires directly to the negative (-) battery terminal or engine block.

•

There must be a ground strap connecting the engine to the chassis.

•

If connecting a ground to the engine block, ensure it is a clean, paint free metal surface.

There are 2 connectors on the end of the case:

GREY Connector (INPUT)

1. Inj 1 In

2. Inj 2 In

3. Inj 3 In

4. Inj 4 In

5. Inj 5 In

6. Inj 6 In

7. Inj 7 In

8. Inj 8 In

9. Inj 9 In

10. Inj 10 In

11. Ground

12. Ground

Pink

Brown

Inj 1 Trigger input

Inj 2 Trigger input

Orange Inj 3 Trigger input

Dark Green Inj 4 Trigger input

Grey Inj 5 Trigger input

Dark Blue Inj 6 Trigger input

Violet

Tan

Yellow

Inj 7 Trigger input

Inj 8 Trigger input

Inj 9 Trigger input

Light Green Inj 10 Trigger input

Black Ground In, Connect to the Battery (-)

Black Ground In, Connect to the Battery (-)

BLACK Connector (OUTPUT)

#

1.

Name

Inj 1 Out

Color

Pink

Function

Inj 1 Output, connect 12V to other side of injector.

2. Inj 2 Out Brown

3. Inj 3 Out Orange

Inj 2 Output, connect 12V to other side of injector.

Inj 3 Output, connect 12V to other side of injector.

4. Inj 4 Out Dark Green Inj 4 Output, connect 12V to other side of injector.

5. Inj 5 Out Grey Inj 5 Output, connect 12V to other side of injector.

6. Inj 6 Out Dark Blue Inj 6 Output, connect 12V to other side of injector.

7. Inj 7 Out Violet Inj 7 Output, connect 12V to other side of injector.

8. Inj 8 Out Tan

9. Inj 9 Out Yellow

Inj 8 Output, connect 12V to other side of injector.

Inj 9 Output, connect 12V to other side of injector.

10. Inj 10 Out Light Green Inj 10 Output, connect 12V to other side of injector.

11. Pos 12V Red +12v in, Connect via fuse to ignition switch.

Red +12v in, Connect via fuse to ignition switch. 12. Pos 12V

12 MONTH LIMITED WARRANTY

Advanced Engine Management Inc. warrants to the consumer that all AEM High Performance products will be free from defects in material and workmanship for a period of twelve (12) months from date of the original purchase. Products that fail within this 12 month warranty period will be repaired or replaced at AEM’s option, when determined by AEM that the product failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of the AEM part. In no event shall this warranty exceed the original purchase price of the AEM part nor shall AEM be responsible for special, incidental or consequential damages or cost incurred due to the failure of this product. Warranty claims to AEM must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month warranty period. Improper use or installation, accident, abuse, unauthorized repairs or alterations voids this warranty. AEM disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by AEM. Warranty returns will only be accepted by AEM when accompanied by a valid Return Goods Authorization (RGA) number. Credit for defective products will be issued pending inspection. Product must be received by AEM within 30 days of the date that the RGA is issued.

Please note that before we can issue an RGA for an AEM Electronic Component, it is first necessary for the installer or end user to contact our Performance Electronics Help Desk at 1-310-484-2322 x303 to discuss the problem. Most issues can be solved over the phone. Under no circumstances should a system be returned or an RGA requested before the above