Omron Healthcare HEM-6181-E RS4 Blood Pressure Monitor Instruction manual

Omron Healthcare HEM-6181-E RS4 Blood Pressure Monitor Instruction manual
Automatic Wrist Blood
Pressure Monitor
RS4 (HEM-6181-E)
Instruction Manual
IM-HEM-6181-E-EN-02-12/2018
2829387-3B
Table of Contents
Introduction
Important Safety Information
1. Know Your Monitor
2. Preparation
3. Using Your Monitor
4. Using Memory Function
5. Other Settings
6. Error Messages and Troubleshooting
7. Maintenance
8. Specifications
9. Limited Warranty
10. Guidance and Manufacturer’s Declaration
Introduction
Thank you for purchasing the RS4 Automatic Wrist Blood Pressure
Monitor. This blood pressure monitor is to be worn on your wrist.
This blood pressure monitor uses the oscillometric method of blood
pressure measurement. When the cuff inflates, this monitor senses
the pressure pulsations of the artery underneath the cuff. The pulses
are called oscillometric pulses. The electronic pressure sensor
displays a digital reading of blood pressure.
Safety Instructions
This instruction manual provides you with important information
about the RS4 Automatic Wrist Blood Pressure Monitor. To ensure
the safe and proper use of this monitor, READ and UNDERSTAND
all of the safety and operating instructions. If you do not understand
these instructions or have any questions, contact your OMRON retail
outlet or distributor before attempting to use this monitor. For specific
information about your own blood pressure, consult with your
physician.
Intended Use
This device is a digital monitor intended for use in measuring blood
pressure and pulse rate in adult patient population with wrist
circumference ranging from 13.5 cm to 21.5 cm. This monitor
detects the appearance of irregular heartbeats during measurement
and gives a warning signal with readings. It is mainly designed for
general household use.
Receiving and Inspection
Remove this monitor from the packaging and inspect for damage. If
this monitor is damaged, DO NOT USE and consult with your
OMRON retail outlet or distributor.
Important Safety Information
Please read the Important Safety Information in this instruction
manual before using this monitor.
Please follow this instruction manual thoroughly for your safety.
Please keep for future reference. For specific information about your
own blood pressure, CONSULT WITH YOUR PHYSICIAN.
Warning
Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.
• DO NOT use this monitor on infants, toddlers, children or
persons who cannot express themselves.
• DO NOT adjust medication based on readings from this blood
pressure monitor. Take medication as prescribed by your
physician. ONLY a physician is qualified to diagnose and treat
high blood pressure.
• DO NOT use this monitor on an injured wrist or a wrist under
medical treatment.
• DO NOT apply the wrist cuff on your wrist while on an
intravenous drip or blood transfusion.
• DO NOT use this monitor in areas containing high frequency
(HF) surgical equipment, magnetic resonance imaging (MRI)
equipment, computerized tomography (CT) scanners. This
may result in incorrect operation of the monitor and/or cause
an inaccurate reading.
• DO NOT use this monitor in oxygen rich environments or near
flammable gas.
• Consult with your physician before using this monitor if you
have common arrhythmias such as atrial or ventricular
premature beats or atrial fibrillation; arterial sclerosis; poor
perfusion; diabetes; pregnancy; pre-eclampsia or renal
disease. NOTE that any of these conditions in addition to
patient motion, trembling, or shivering may affect the
measurement reading.
• NEVER diagnose or treat yourself based on your readings.
ALWAYS consult with your physician.
• This product contains small parts that may cause a choking
hazard if swallowed by infants, toddlers or children.
• DO NOT take measurements more often than necessary
because bruising, due to blood flow interference, may occur.
• ONLY inflate the wrist cuff when it is applied on your wrist.
• Remove the wrist cuff if it does not start deflating during a
measurement.
• DO NOT use this monitor for any purpose other than
measuring blood pressure.
• During measurement, make sure that no mobile device or any
other electrical device that emits electromagnetic fields is
within 30 cm of this monitor. This may result in incorrect
operation of the monitor and/or cause an inaccurate reading.
• DO NOT disassemble or attempt to repair this monitor or
other components. This may cause an inaccurate reading.
• DO NOT use in a location where there is moisture or a risk of
water splashing this monitor. This may damage this monitor.
• DO NOT use this monitor in a moving vehicle such as in a car.
• DO NOT drop or subject this monitor to strong shocks or
vibrations.
• DO NOT use this monitor in places with high or low humidity
or high or low temperatures. Refer to chapter 8.
• Ensure this monitor is not impairing blood circulation by
observing the wrist while measurement is occurring.
• DO NOT use this monitor in high-use environments such as
medical clinics or physician offices.
• DO NOT use this monitor with other medical electrical (ME)
equipment simultaneously. This may result in incorrect
operation of the monitor and/or cause an inaccurate reading.
• Avoid bathing, drinking alcohol or caffeine, smoking,
exercising and eating for at least 30 minutes before taking a
measurement.
• Rest for at least 5 minutes before taking a measurement.
• Remove tight-fitting, thick clothing and any accessories from
your wrist while taking a measurement.
• Remain still and DO NOT talk while taking a measurement.
• ONLY use this monitor on persons whose wrist
circumference is within the specified range of the cuff.
• Ensure that this monitor has acclimated to room temperature
before taking a measurement. Taking a measurement after an
extreme temperature change could lead to an inaccurate
reading. OMRON recommends waiting for approximately 2
hours for the monitor to warm up or cool down when the
monitor is used in an environment within the temperature
specified as operating conditions after it is stored either at
the maximum or at the minimum storage temperature. For
additional information of operating and storage/transport
temperature, refer to chapter 8.
• DO NOT crease the wrist cuff excessively.
• Read and follow the “Correct Disposal of This Product” in
chapter 10 when disposing of the device and any used
accessories or optional parts.
• DO NOT use this monitor after the durable period has ended.
Refer to chapter 8.
Battery Handling and Usage
• DO NOT insert batteries with their polarities incorrectly
aligned.
• ONLY use 2 “AAA” alkaline batteries with this monitor. DO
NOT use other types of batteries. DO NOT use new and used
batteries together. DO NOT use different brands of batteries
together.
• Remove batteries if this monitor will not be used for a long
period of time.
• If battery fluid should get in your eyes, immediately rinse with
plenty of clean water. Consult with your physician
immediately.
• If battery fluid should get on your skin, wash your skin
immediately with plenty of clean, lukewarm water. If irritation,
injury or pain persists, consult with your physician.
• DO NOT use batteries after their expiration date.
• Periodically check batteries to ensure they are in good
working condition.
• ONLY use batteries specified for this monitor. Use of
unsupported batteries may damage and/or may be hazardous
to this monitor.
Caution
Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury to the user or patient, or cause
damage to the equipment or other property.
• Stop using this monitor and consult with your physician if
you experience skin irritation or discomfort.
• Consult with your physician before using this monitor on a
wrist where intravascular access or therapy, or an arteriovenous (A-V) shunt, is present because of temporary
interference to blood flow which could result in injury.
• Consult with your physician before using this monitor if you
have had a mastectomy.
• Consult with your physician before using this monitor if you
have severe blood flow problems or blood disorders as cuff
inflation can cause bruising.
2.1
Memory symbol
Appears when viewing readings stored in the memory.
D Diastolic blood pressure reading
Pulse display / Memory number
F
G
wrist.
Heartbeat symbol
Flashes while taking a measurement.
3. Close the battery cover.
Appears when viewing the weekly average readings
taken in the morning.
Weekly averages for the measurement taken in the
morning within 4 weeks appear on the display.
Appears when viewing the average readings of the
latest 2 or 3 readings taken within 10 minutes span.
Battery symbol (low)
J
Flashes when batteries are low.
Battery symbol (depleted)
Appears when batteries are depleted.
Hypertension symbol
K
Appears if your systolic blood pressure is 135 mmHg or
above and/or the diastolic blood pressure is 85 mmHg
or above.
Morning hypertension symbol
Appears when the morning weekly average is 135/85
mmHg or above.
Positioning indicator
Your monitor has a built-in advanced positioning sensor
that is used as an aid in determining if the monitor is at
the correct height.
L
The “
” symbol appears when your monitor is at the
correct position relative to your heart during a
measurement. When your monitor is higher or lower
position relative to your heart, the heart position locator
bar will appear up above, or below the heart symbol to
guide correct wrist positioning.
M
Normal Heartbeat
Appears along with
Pulse
readings when an
irregular rhythm is
Blood pressure
detected 2 or more
times during a
measurement.
Irregular Heartbeat
Short Long
An irregular heartbeat
Pulse
rhythm is defined as a
Blood pressure
rhythm that is 25%
less or 25% more
than the average rhythm detected while your monitor is
measuring blood pressure. If it continues to appear, we
recommend you to consult with and follow the directions
of your physician.
1.2
Cuff wrap guide symbol (OK)
Monitor
d
O
c
1.3
A
Cuff wrap guide symbol (loose)
f
Appears if the wrist cuff is not wrapped around the wrist
correctly while taking a measurement. It also appears
when viewing past readings.
2013 ESH/ESC* Guidelines for the management of
arterial hypertension
Definitions of hypertension by office and home blood pressure levels
Display and Symbols
H
I
B
J
K
C
L
D
M
E
N
F
O
G
Appears if the wrist cuff is wrapped around the wrist
correctly while taking a measurement. It also appears
when viewing past readings.
e
a. Wrist cuff
(Wrist circumference 13.5 cm to 21.5 cm)
b. Display
c. Battery compartment
d. [Memory] button
e. [Morning average] button
f. [START/STOP] button
2.2
Wrist cuff
1. Press the
or
clearance of 1 to 2 cm between
the cuff and the bottom of your
palm.
1 to 2 cm
4. Wrap the wrist cuff firmly around
your wrist. Do not apply over
clothing.
Check to make sure that there is no gap
between your wrist and the cuff.
button once to adjust the year.
Press and hold the
button to quickly advance the years.
Press and hold the
through the years.
button to quickly go backwards
the “
” symbol will appear. When your wrist is higher or
lower position relative to your heart, a locator bar will appear
according to the wrist position. Due to difference in individual
size and physique, this feature may not be helpful in all cases
and you may wish to disable this feature. If you feel the position
of the wrist according to positioning indicator's guidance does
NOT match your heart level, disable this feature and follow
your judgement. To disable it, refer to section 5.1.
3. Position the wrist cuff leaving a
Setting the Date and Time
Note
• Set your monitor to the correct date and time before taking a
measurement for the first time.
• As soon as batteries are correctly installed, the year flashes on the
display of your monitor.
1. Press the [START/STOP] button.
Monitor height
Wrist is too high
Note
• Make sure the wrist cuff does not
cover the protruding part of the wrist
bone on the outside of your wrist.
2. Press the [START/STOP] button to confirm the year and
the month will flash. Repeat the same steps to adjust
the month, day, hour, and minute.
Proper position
Wrist is too low
Monitor, 2 “AAA” alkaline batteries, storage case, instruction manual
b
Note
• When the “
” symbol flashes on the display, it is recommended
you replace batteries.
• To replace batteries, turn your monitor off and remove all batteries.
Then replace with 2 new alkaline batteries at the same time.
• As soon as batteries are correctly installed, the year flashes on the
date and time display to set the date and time.
• Replacing batteries will not delete previous readings.
• The supplied batteries may have a shorter life than new batteries.
• Disposal of used batteries should be carried out in accordance
with local regulations.
Caution
• DO NOT use this monitor with other medical electrical (ME)
equipment simultaneously. This may result in incorrect operation
of the monitor and/or cause an inaccurate reading.
• Remain still and DO NOT talk while taking a measurement.
Irregular heartbeat symbol
N
a
Your palm and monitor display should both
face upward.
Average value symbol
I
Taking a Measurement
Note
• To stop the measurement, press the [START/STOP] button once
to deflate the wrist cuff.
Your monitor has a built-in advanced positioning sensor that is
used as an aid in determining if the monitor is at the correct
height. It has been designed to work with most people so that
when your wrist is at the correct position relative to your heart,
2. Put your wrist through the cuff loop.
1
3.1
2. Check the positioning indicator.
Roll up sleeve. Make sure your
sleeve is not rolled up too tightly on
your arm. This may constrict the flow
of blood in your arm.
2
3. Using Your Monitor
All symbols appear on the display before starting the
measurement.
1. Apply the wrist cuff to your left
Movement error symbol
Contents
Caution
• Remove tight-fitting, thick clothing and any accessories from your
wrist while taking a measurement.
indicated in the battery compartment.
Appears during cuff deflation.
Morning average symbol
H
2. Insert 2 “AAA” alkaline batteries as
Deflation symbol
Appears along with readings when your body is moving
during a measurement. If it appears, remove the wrist
cuff, and wait for 2 to 3 minutes. Then, remain still and
take another measurement.
1.1
Installing Batteries
cover and pull downward.
Pulse rate appears after the measurement.
E When pressing the
button, the memory number appears
for approximately one second before the pulse rate appears on
the display.
Applying the Wrist Cuff
Note
• Following steps are for applying the wrist cuff to your left wrist.
When you take a measurement on your right wrist, apply the wrist
cuff using the same steps as on your left wrist.
• The blood pressure can differ between the right wrist and the left
wrist, and the measured blood pressure values can be different.
OMRON recommends to always use the same wrist for
measurement. If the values between both wrists differ
substantially, please check with your physician as to which wrist to
use for your measurements.
1. Push down the hook of the battery
C Systolic blood pressure reading
1. Know Your Monitor
Battery Handling and Usage
• Keep batteries out of the reach of infants, toddlers or
children.
B
2.4
2. Preparation
A Date and time display
Office
Home
Systolic Blood
Pressure
≥ 140 mmHg
≥ 135 mmHg
Diastolic Blood
Pressure
≥ 90 mmHg
≥ 85 mmHg
These ranges are from statistical values for blood pressure.
* European Society of Hypertension (ESH) and European Society
of Cardiology (ESC).
Warning
• NEVER diagnose or treat yourself based on your readings.
ALWAYS consult with your physician.
2.5
Year
To take a measurement, you
need to be relaxed and
comfortably seated in a room with
a comfortable temperature. Place
your elbow on the table to support
your arm.
Month
Day
Hour
Minute
3. Press the [START/STOP] button to store the setting.
It automatically turns off after 3 seconds.
Note
• If you need to reset the date and time, replace batteries or press
and hold the
button until the year flashes, and set the date
and time as above steps.
2.3
Sitting Correctly
Blood Pressure Measurement Tips
To help ensure an accurate reading, follow these directions:
• Stress raises blood pressure. Avoid taking measurements during
stressful times.
• Measurements should be taken in a quiet place.
• It is important to take measurements at same times each day.
Taking measurements in the morning and in the evening is
recommended.
• Remember to have a record of your blood pressure and pulse
readings for your physician. A single measurement does not
provide an accurate indication of your true blood pressure.
Please use the Blood Pressure Diary to keep records of several
readings over a certain period of time. To download PDF files of
the diary, visit www.omron-healthcare.com.
Caution
• Avoid bathing, drinking alcohol or caffeine, smoking, exercising
and eating for at least 30 minutes before taking a measurement.
• Rest for at least 5 minutes before taking a measurement.
• Sit in a chair with your legs
uncrossed and your feet flat on
the floor.
• Sit with your back and arm
being supported.
• Your monitor must be
approximately the same level
as your heart. If the monitor is
too high above your heart, your blood pressure will be artificially
low. If the monitor is too low below your heart, your blood pressure
will be artificially high.
• Relax your wrist and hand. Do not bend your wrist back, clench
your fist, or bend your wrist forward.
Positioning indicator
Any locator bar (-) above
the “
The “
” symbol appears.
” symbol appears.
Any locator bar (-) below
the “
” symbol appears.
Note
• After 5 seconds from pressing the [START/STOP] button,
even if your monitor is not positioned properly, your monitor
will start the measurement and the wrist cuff will start to
inflate.
3. Remain still and do not move or talk until the entire
measurement process is completed.
As the cuff inflates, your monitor automatically determines your
ideal inflation level. This monitor detects your blood pressure
and pulse rate during inflation.
The “
” symbol flashes at every heartbeat.
Note
• The “
” symbol appears if the wrist cuff is wrapped
around the wrist correctly.
• When the “
” symbol is displayed, the wrist cuff is not
applied correctly. Press the [START/STOP] button to turn
your monitor off, then apply the cuff correctly.
After your monitor has detected your blood pressure and pulse
rate, the cuff automatically deflates. Your blood pressure and
pulse rate are displayed.
If either the systolic or the diastolic reading is high (refer to
section 1.3), the “
” symbol appears.
START
INFLATING
COMPLETED
4. Press the [START/STOP] button to turn your monitor off.
Note
• Your monitor will automatically turn off after 2 minutes.
• Wait 2-3 minutes between measurements. The wait time
allows the arteries to decompress and return to their premeasurement form. You may need to increase the wait time
depending on your individual physiological characteristics.
4. Using Memory Function
5. Other Settings
Your monitor automatically stores up to 60 readings.
5.1
4.1
The positioning indicator is enabled as default.
Viewing the Readings Stored in Memory
1. Press the
Display/
Problem
for more than 10 seconds.
button
Alternating
date/time
display
Note
• Your monitor will automatically turn off after 3 seconds from
the completion.
• To enable the positioning indicator, follow the same steps as
above.
The Memory number appears for one second before the pulse
rate is displayed. The most recent reading set is numbered “1”.
Note
• If the positioning indicator is enabled, the positioning
indicator is displayed with the readings.
• If the reading is high (refer to section 1.3),
the “
” symbol appears.
• If there are no readings stored in the
memory, the screen to the right is displayed.
• If the memory is full, the monitor will delete
the oldest readings.
2. Press the
button repeatedly to scroll through the
previous readings stored in the memory.
4.2
5.2
Deleting All Readings Stored in Memory
1. Press the
button, then the “
” symbol appears.
2. While holding the
button down, press
and hold the [START/
STOP] button for more
than 2 seconds.
Viewing the Average Reading
Your monitor can calculate an average reading based on the latest 2
or 3 readings taken within 10 minutes span.
Note
• All readings will be deleted. You cannot partially delete the
readings stored in the memory.
1. When your monitor is off, press and hold the
button for more than 2 seconds.
Note
• If there are only 2 readings in the memory
for that period, the average will be based on
these 2 readings.
• If the average reading is high (refer to
section 1.3), the “
” symbol appears.
6. Error Messages and Troubleshooting
In case of any of the below problems occur during measurement,
first check that no other electrical device is within 30cm. If the
problem persists, please refer to the table below.
Display/
Problem
4.3
Possible Cause
Viewing Morning Weekly Averages
Your monitor calculates and displays weekly averages for the
measurements taken in the morning for 4 weeks.
1. Press the
button once.
section 1.3), the “
The wrist cuff is not
applied correctly.
appears or the
wrist cuff does
Air is leaking from the
not inflate.
wrist cuff.
The morning weekly average for the current
week “THIS WEEK” appears on the display.
If the morning weekly average is high (refer to
” symbol appears.
appears
appears
/
appears
The pulse rate is not
detected correctly.
Tuesday
Wednesday
Thursday
Friday
Saturday
4:00
1
2
3
The first 3 measurements
Do not touch the wrist
cuff while taking a
measurement.
Apply the wrist cuff
correctly, then take
another measurement.
Refer to section 2.4.
Remain still and sit
correctly during a
measurement.
If the “
” symbol
continues to appear, we
recommend you to
consult with your
physician.
Measurements of the morning
Monday
Contact your OMRON
retail outlet or
distributor.
You move or talk during
Remain still and do not
a measurement.
talk during a
Vibrations disrupt a
measurement.
measurement.
3. Press the [START/STOP] button to turn off your monitor.
Sunday
Apply the wrist cuff
correctly, then take
another measurement.
Refer to section 2.4.
appears
button repeatedly to display the average
for the previous weeks.
Morning Weekly Average Calculation
This is the average for the measurements taken during the morning
(4:00 - 9:59) between Sunday and Saturday. Only the first 3
measurements taken in the morning between 4:00 - 9:59 will be
used to calculate the morning average for each day.
Solution
The wrist cuff is
overinflated exceeding
300 mmHg.
2. Press the
Your monitor displays “-1 WEEK” for the previous week's
average, to “-3 WEEK” for the oldest set of averages.
appears
4
9:59
Solution
Disabling/Enabling Positioning Indicator
1. When your monitor is off, press and hold the
button.
Possible Cause
appears
appears
Your wrist is moved up
and down during a
measurement.
Do not move your wrist,
then take another
measurement.
Refer to chapter 3.
The monitor is
malfunctioned.
Press the [START/
STOP] button again. If
“Er” still appears,
contact your OMRON
retail outlet or
distributor.
heart symbol
Enable the positioning
The positioning indicator
The heart
indicator. Refer to
is
disabled.
symbol in the
section 5.1.
positioning
indicator does
not appear and
a locator bar
does not
appear.
flashes
Batteries are low.
appears or the
monitor is
Batteries are depleted.
turned off
unexpectedly
during a
measurement
Immediately replace all
batteries with 2 new
alkaline batteries. Refer
to section 2.1.
Batteries are completely
No power.
depleted.
Nothing
Check the battery
appears on the
Battery polarities are not installation for proper
display of the
properly aligned.
placement. Refer to
monitor.
section 2.1.
8. Specifications
10. Guidance and Manufacturer’s Declaration
Product category
Electronic Sphygmomanometers
Product description
Automatic Wrist Blood Pressure Monitor
Model (Code)
RS4 (HEM-6181-E)
Display
LCD digital display
Cuff pressure range
0 to 299 mmHg
Blood pressure
measurement range
SYS: 60 to 260 mmHg
DIA: 40 to 215 mmHg
Pulse measurement
range
40 to 180 beats / min.
Accuracy
Pressure: ±3 mmHg
Pulse: ±5% of display reading
Inflation
Automatic by electric pump
Deflation
Automatic rapid deflation
Measurement method
Oscillometric method
Blood pressure varies constantly. Many factors
Readings
including stress, time of day, and/or how you
appear too high apply the wrist cuff, may affect your blood
or too low.
pressure. Review sections 2.3 - 2.5 and chapter
3.
Operation mode
Continuous operation
IP classification
IP 22
Press the [START/STOP] button to turn the
monitor off, then press it again to take a
measurement. If the problem continues, remove
Any other
all batteries and wait for 30 seconds. Then reproblems occur.
install batteries.
If the problem still persists, contact your OMRON
retail outlet or distributor.
7. Maintenance
7.1
Caution
• DO NOT disassemble or attempt to repair this monitor or other
components. This may cause an inaccurate reading.
Storage
Keep your monitor in the storage case when not in use.
• Store your monitor in a clean, safe location.
Do not store your monitor:
• If your monitor is wet.
• In locations exposed to extreme temperatures, humidity, direct
sunlight, dust or corrosive vapors such as bleach.
• In locations exposed to vibrations or shocks.
7.3
Cleaning
• Do not use any abrasive or volatile cleaners.
• Use a soft dry cloth or a soft cloth moistened with neutral soap to
clean your monitor and wrist cuff, and then wipe them with a dry
cloth.
• Do not wash or immerse your monitor and wrist cuff in water.
• Do not use gasoline, thinners or similar solvents to clean your
monitor and wrist cuff.
7.4
DC3 V 3.0 W
Power source
2 “AAA” alkaline batteries 1.5V
Battery life
Approximately 300 measurements (using
new alkaline batteries)
Durable period (Service
5 years
life)
Operating conditions
+10°C to +40°C / 15 to 90% RH (noncondensing) / 800 to 1060 hPa
Storage / Transport
conditions
-20°C to +60°C / 10 to 90% RH (noncondensing)
Weight
Approximately 86 g not including
batteries
Dimensions
Approximately 93 mm (w) × 62 mm (h) ×
20 mm (l)
(not including the wrist cuff)
Measurable wrist
circumference
13.5 to 21.5 cm
Memory
Stores up to 60 readings
Contents
Monitor, storage case, 2 “AAA” alkaline
batteries, instruction manual
Protection against
electric shock
Internally powered ME equipment
Applied part
Type BF (wrist cuff)
Maximum temperature
of the applied part
Lower than +48°C
Maintenance
To protect your monitor from damage, please follow the directions
below:
• Changes or modifications not approved by the manufacturer will
void the user warranty.
7.2
Rating
Calibration and Service
• The accuracy of this blood pressure monitor has been carefully
tested and is designed for a long service life.
• It is generally recommended to have the unit inspected every two
years to ensure correct functioning and accuracy. Please consult
your authorised OMRON dealer or the OMRON Customer Service
at the address given on the packaging or attached literature.
• This device fulfils the provisions of EC directive 93/42/EEC
(Medical Device Directive).
• This blood pressure monitor is designed according to the
European Standard EN1060, Non-invasive sphygmomanometers
Part 1: General Requirements and Part 3: Supplementary
requirements for electromechanical blood pressure measuring
systems.
• This OMRON product is produced under the strict quality system
of OMRON HEALTHCARE Co., Ltd., Japan. The Core component
for OMRON blood pressure monitors, which is the Pressure
Sensor, is produced in Japan.
Symbols description
Applied part - Type BF
Degree of protection against electric
shock (leakage current)
IP XX
Ingress protection degree provided by
IEC 60529
CE Marking
Serial number
Temperature limitation
Humidity limitation
Atmospheric pressure limitation
Need for the user to consult this
instruction manual.
Indicates the correct positioning for the
monitor on the wrist
Measurable wrist circumference
Battery
Direct current
Note
• These specifications are subject to change without notice.
• In the clinical validation study, K5 was used on 85 subjects for
determination of diastolic blood pressure.
• This monitor is clinically investigated according to the
requirements of ISO 81060-2:2013.
• IP classification is degrees of protection provided by enclosures in
accordance with IEC 60529. This monitor is protected against
solid foreign objects of 12.5 mm diameter and greater such as a
finger, and against oblique falling water drops which may cause
issues during a normal operation.
• This device has not been validated for use on pregnant patients.
9. Limited Warranty
Thank you for buying an OMRON product. This product is
constructed of high quality materials and great care has been taken
in its manufacturing. It is designed to give you every satisfaction,
provided that it is properly operated and maintained as described in
the instruction manual.
This product is warranted by OMRON for a period of 3 years after
the date of purchase. The proper construction, workmanship and
materials of this product is warranted by OMRON. During this period
of warranty OMRON will, without charge for labour or parts, repair or
replace the defect product or any defective parts.
The warranty does not cover any of the following:
A. Transport costs and risks of transport.
B. Costs for repairs and / or defects resulting from repairs done by
unauthorised persons.
C. Periodic check-ups and maintenance.
D. Failure or wear of optional parts or other attachments other than
the main device itself, unless explicitly warranted above.
E. Costs arising due to non-acceptance of a claim (those will be
charged for).
F. Damages of any kind including personal caused accidentally or
from misuse.
G. Calibration service is not included within the warranty.
Should warranty service be required please apply to the dealer
whom the product was purchased from or an authorised OMRON
distributor. For the address refer to the product packaging / literature
or to your specialised retailer. If you have difficulties in finding
OMRON customer services, contact us for information.
www.omron-healthcare.com
Repair or replacement under the warranty does not give rise to any
extension or renewal of the warranty period.
The warranty will be granted only if the complete product is returned
together with the original invoice / cash ticket issued to the
consumer by the retailer.
Important information regarding Electro Magnetic Compatibility
(EMC)
HEM-6181-E manufactured by OMRON HEALTHCARE Co., Ltd. conforms to
EN60601-1-2:2015 Electro Magnetic Compatibility (EMC) standard.
Further documentation in accordance with this EMC standard is available at
www.omron-healthcare.com. Refer to the EMC information for HEM-6181-E on the
website.
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
This marking shown on the product or its literature, indicates that it
should not be disposed of, with other household wastes at the end
of its working life.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this product from
other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can
return this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract. This product should not be mixed with other commercial
waste for disposal.
Manufacturer
OMRON HEALTHCARE Co., Ltd.
53, Kunotsubo, Terado-cho, Muko, KYOTO,
617-0002 JAPAN
EU-representative OMRON HEALTHCARE EUROPE B.V.
Scorpius 33, 2132 LR Hoofddorp,
THE NETHERLANDS
www.omron-healthcare.com
Production
facility
Replacing all batteries
with 2 new alkaline
batteries is
recommended. Refer to
section 2.1.
OMRON HEALTHCARE MANUFACTURING
VIETNAM CO., LTD.
No.28 VSIP II, Street 2, Vietnam-Singapore
Industrial Park II, Binh Duong
Industry-Services-Urban Complex,
Hoa Phu Ward, Thu Dau Mot City,
Binh Duong Province, Vietnam
OMRON HEALTHCARE UK LTD.
Opal Drive, Fox Milne, Milton Keynes, MK15
0DG, UK
www.omron-healthcare.com
Subsidiaries
OMRON MEDIZINTECHNIK
HANDELSGESELLSCHAFT mbH
Konrad-Zuse-Ring 28, 68163 Mannheim,
GERMANY
www.omron-healthcare.com
OMRON SANTÉ FRANCE SAS
14, rue de Lisbonne, 93561 Rosny-sous-Bois
Cedex, FRANCE
www.omron-healthcare.com
Made in Vietnam
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement