- Vehicles & accessories
- Motor vehicle electronics
- Car speakers
- Cardo Systems
- Q-solo
- Installation Guide
advertisement
▼
Scroll to page 2
CONTENTS INSTALLING THE AUDIO KIT ON YOUR HELMET 1 Cradle 6 Alcohol pads A Hybrid microphone B Release tab 7 Speaker booster pads 8 Rectangular velcro pads 2 Speakers 9 Square velcro pads 3 Speaker jack 10 Glue Plates (choose 1) 4 Replacement microphone sponge 5 Allen wrench 11 Hybrid microphone clip A 12 Backplate OPTION A – USING THE BACKPLATE PARTS REQUIRED (OPTION A): 1 Remove the Backplate by taking out both screws 2 Use the Alcohol pad to clean the exact spot on the helmet 3 2 ENhttp://cardosystems.com/q-solo-download 1 2 3 for your helmet 4 9 5 10 FRhttp://cardosystems.com/q-solo-download Alcohol Pad pour un manuel et un guide de poche en français IThttp://cardosystems.com/q-solo-download 7 Alcohol Pad 11 Push the Backplate between the helmet’s outer shell and inner padding Tighten the screws Installation Guide 4 Press the Glue Plate onto the helmet for 15 seconds as shown 5 Allow the glue to dry for 24 hours 6 Attach cradle to the Glue Plate and fasten both screws tightly 1 2 3 12 per il manuale e la guida tascabile in italiano 8 24 hours ● Peel off protective backing sheet Loosen both screws for a manual and pocket guide in English para un manual y la guía de bolsillo en español Press THIS CAN ONLY BE DONE ONCE! 3 ● Choose which of the two Glue Plates is most suitable für eine Bedienungsanleitung und eine Kurzanleitung in Deutsch EShttp://cardosystems.com/q-solo-download or Attach the scala rider audio Kit to your helmet using the standard Backplate (Option A) or one of the Glue Plates (Option B). B 1 DE http://cardosystems.com/q-solo-download OPTION B – USING THE GLUE PLATE PARTS REQUIRED (OPTION B): * For details on attaching or removing the unit from the audio kit, refer to the back side of this installation guide. DISCLAIMER The Glue Plate is offered as a secondary option yet Cardo does not recommend using it, unless the Backplate cannot be installed on your helmet. Cardo shall bear no responsibility whatsoever for damage of any kind caused as a result of gluing. POSITIONING THE HYBRID MICROPHONE PLACING THE SPEAKERS ATTACHING AND REMOVING THE UNIT FROM THE AUDIO KIT PARTS REQUIRED: PARTS REQUIRED: 1 ATTACHING Click! 1 Remove the left cheek pad to expose the inner shell ● Clean the designated area ● Peel off and stick the velcro pad and attach the hybrid Microphone in place. ● For a more secure attachment use the second velcro pad and the supplied clip as shown. 2 Ensure arrow is positioned towards your mouth. 2 For best clarity, place speakers directly opposite and close to the ears. Helmets with deep recesses may require padding to bring the speakers closer for ideal positioning. Optional speaker booster pads are provided for this purpose. 1 Remove both cheek pads to expose the inner shell ● Clean the designated area REMOVING ● Peel off and stick the velcro pads ** To use the optional speaker booster pads , place them between the Velcro pad and the speaker. 2 2 Attach the speaker with the shorter wire onto the 1 Push left velcro pad. Cross the long speaker wire over the center of the helmet to enhance FM radio reception. Attach the second speaker onto the right Velcro pad. 2 Slide up 3 Re-attach the cheek pads. MAN01010 InstallationGuide2017EN 015 www.cardosystems.com 1 3 [email protected] USA & Canada: 1-800-488-0363 International: +49 89 450 36819 Using two speakers inside the helmet may be prohibited in certain jurisdictions. If this is the case, position both speakers on one side of the helmet.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project