Power Fist 0140084 Precision Burner Torch Owner's Manual

Add to My manuals
1 Pages

advertisement

Power Fist 0140084 Precision Burner Torch Owner's Manual | Manualzz
HOTERY
QUICKFIT
BURNER TORCH
MICRO TORCH
GAS BURNER
TURBO TORCH
INSTRUCTION MANUAL
+ HT-21A - HT-21B
* HT-31A * HT-31B
* HT-32A * HT-32B
* HT-41A * HT-41B
+ HT-21C + HT-21D
+ HT-31C + HT-31D
+ HT-41C + HT-41D
INSTRUCTION
ASSEMBLY:
1)Make sure valve is OFF by turning knob in direction of arrow until hand tight only. DO NOT FORCE.
2)Turn fuel cylinder clockwise into valve body until hand tight. DO NOT FORCE. (as per shown below)
OPERATION AND LIGHTING:
1)Use only high quality Butane or Propane gas cylinder.
2)Make sure the on/off adjustment knob is in "OFF" position.
3)Shaking gas container a few times to warm the fuel up.
4)Turn the adjustment knob counter- clockwise to 2/3 circle.
The gas will blow out with a "HISS® sound from the mouth.
(fig 182) Кит 7
5)Press "IGNITION BUTTON" and the flame will ignite instantly. HT-21
PUSH
HT-31/HT-41
WARNING:
1)The Propane cylinder contains gaseous and liquid propane. If the torch is moved rapidly, tilted too far to the
side or upside down, the liquid can enter the valve and cause the flame to flare or extinguish.
To prevent this adjust the torch to a 1/4" long inner flame and let the torch warm-up for 3 minutes, prior to
such movement, and then slowly re-adjust as necessary once the torch is in desired operating position.
2)Make sure torch is cool before tightening or removing burner head, or before installing or removing acces-
sories.
3)Cold weather operation
a.)In cold weather the size of the flame will be smaller. To produce a larger flame, pre- warm the cylinder to
room temperature prior to use.
b.)There is a greater possibility that the flame will extinguish when the torch is turned upside down in cold
weather.
TEMPERATURE ADJUSTMENT:
- For hottest, most efficient, adjust inner blue flame of pencil burner to 1-1/2 to 2 inch in Length. Adjust utility
burner to 1/2 to 3/4 inch length.
TURNING OFF AND STORAGE:
REMOVE CYLINDER FROM TORCH WHEN NOT IN USE.
1.)Turn valve off.
2.)When torch is cool, turn fuel cylinder counter clockwise from valve body to disconnect. (Fig 3&4), then store
torch and cylinder separately. Observe cautions on cylinder label.
Fig.1 » Fig.2 Fig.3
GENERAL SAFETY RULES:
1.)Read and follow operating instructions and cautions and familiarize yourself with the torch before lighting or
using.
Review instructions and cautions periodically to maintain awareness. Do not try to operate before reading
instructions.
2.)Do not point torch towards face, other persons or flammable objects. Never attempt to use torch as a
cigarette lighter.
3.)Disconnect cylinder when not in use.
4.)Never attempt to modify the torch construction and never use unapproved fuels.
5.)Treat the torch as you would any fine tool or instrument. Do not drop or otherwise abuse.
6.)Do not use a leaking, damaged or malfunctioning torch.
7.)Work only in well-ventilated areas.
8.)Avoid contact of flux with skin or eyes.
9.)Always place your work on firebrick. If you are not sure it is firebrick, do not use it. Ordinary brick and
concrete can explode when subjected to high temperatures. Do not work on wood or metal surfaces. Always
shield your work.
10.)Always wear protective gloves and use proper tools to handle hot work.
11.)Be aware that the tip of the torch can get extremely hot during use. Take precautions to proect yourself and
others from accidental burns. Never use the torch on or near combustibles. Be especially careful around
motor vehicles or any gasoline- fired products and beware of hidden fuel lines and tanks.
12.)Always make certain the torch is placed on a level surface when connected to the fuel cylinder to reduce
the risk of accidental tip over. Be sure torch is not pointed in is not pointed in a direction which could cause
nearby objects to ignite when torch is set down.
13.)When thawing pipes, be very careful not to overheat surrouding materials.
14.)Always have a fire exetinguisher and a bucket of water near the torch and work area. Do not place them in
the flame path or in a location where you could not reach them should a fire break out.
DANGER:
EXTREMELY FLAMMABLE. CONTENTS UNDER PRESSURE. Keep away from heat or flam. It is illegal and
dangerous to refill the cylinder. Obtain new cylinder from your dealer. Keep out of reach of children. Avoid
prolonged exposure to sunlight. Do not store near heat or in a room used for habitation. Always close burner
valve and wait at least 30 seconds before removing burner from cylinder. Always detach cylinder from burner-
when not in use. Do not breathe gas, fumes, vapor or spray. If inhaled, remove affected person to fresh air.
Avoid contact with skin and eyes. For skin contact, flush with large amounts of water. In case of contact with
eyes, rinse immediately with plerity of water and seek medical advise. When cylinder is empty, discard in a safe
place. Do not throw in fire. Do not puncture or incinerate container.

advertisement

Key Features

  • Powerful motor for tackling tough jobs
  • Durable construction for long-lasting use
  • Versatile design for a variety of tasks
  • Ergonomic handle for comfortable use
  • Lightweight and portable for easy transport
  • Easy to use and maintain

Related manuals

Frequently Answers and Questions

What is the Power Fist 0140084 best used for?
The Power Fist 0140084 is a versatile tool that can be used for a variety of tasks, including drilling, driving screws, and mixing paint.
How powerful is the Power Fist 0140084?
The Power Fist 0140084 has a powerful motor that can deliver up to 1,500 RPM.
How durable is the Power Fist 0140084?
The Power Fist 0140084 is made from durable materials that are designed to withstand heavy use.
Is the Power Fist 0140084 easy to use?
Yes, the Power Fist 0140084 is easy to use and requires minimal maintenance.
Download PDF

advertisement