System Remote Control SR-260 SR-260 buttons User Guide SR-260 SR-260-I A A Use the SR-260 to control devices throughout your Control4 home automation system. B B C C D D Features E E • • • F F G G H H I I • • • • • • Navigate system menus and access media on a TV or other display using the on-screen TV interface. Navigate system menus and access media using the remote’s own text-based List interface. Two-way communication with your Control4 system. Backlit display with a text-based visual interface. 50 buttons total, including quick access buttons, transport control buttons, and a full alphanumeric keypad. All buttons are programmable. Wakes from sleep mode when picked up or moved (if enabled). Ambient light sensor automatically changes the keypad brightness, depending on the light in the room. Recharging station available. J J K K L L M M N N O O P P Quick access buttons Use the remote’s WATCH and LISTEN buttons to quickly select from all playback devices in the room or to select the most recently used device (depending on how the installer configured your system). These buttons can be configured by your Control4 Dealer. See the Control4 System User Guide to learn how to navigate through the system menu and discover all of the features and functions of your Control4 system. Programmable buttons All buttons on the remote are programmable, but the buttons listed below are the most commonly programmed. If these buttons have been programmed by your installer, note their functions here: A Control4 button—Displays Control4 menu on TV (if enabled) B OFF _______________________________________________ C Display—Screen that displays List Navigator _______________________________________________ D WATCH —Displays video sources or plays most recently watched source _______________________________________________ E LISTEN —Displays audio sources or plays most recently played source F LIST —Displays the system menu (List interface) on the remote’s display screen _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ 1 —Turns room off G Programmable buttons—Functions vary (installer programs) H GUIDE —Displays TV listings ▲PAGE —Scrolls pages up PAGE▼ —Scrolls pages down PREV —Returns to previous channel or screen I VOL J SELECT and directional buttons—Moves through menus and selects menu items _______________________________________________ K L —Controls device volume M CH+– —Changes TV channels —Toggles device sound MUTE INFO —Shows program information MENU —Accesses device features and settings BACK —Sends “Back” or “Exit” command Playback control buttons Rewinds / fast forwards Skips back/forward Plays the current AV source Starts recording Stops record or playback Pauses DVR Controls the DVR N Programmable buttons—Functions vary (installer programs) O Alphanumeric buttons—Directly enters channel numbers or text descriptions P Special characters—Alphanumeric buttons that can also be programmed to work directly with a device Install and maintain batteries To install the batteries: 1 Install the four AA alkaline batteries (included) into the back of the remote according to the diagram in the battery compartment (with the + terminals pointing toward the bottom of the remote). Important: The use of rechargeable AA batteries is not supported. Using rechargeable AA batteries may result in inaccurate battery gauge readings. Battery use and care tips • • Keep battery contacts and compartment clean. Remove batteries if the remote is not expected to be used for several months. Do not mix new and old batteries. After removing old batteries, wait 20 seconds before inserting new batteries. Extreme temperatures reduce battery performance. Avoid putting the System Remote Control in very warm places. • • • Battery replacement safety rules CAUTION! To prevent battery shorting, leakage, or rupture: • • • Use typical AA Alkaline batteries only. Do not mix battery types. Do not attempt to recharge a battery unless the battery is specifically marked “rechargeable.” • Never dispose of batteries in a fire. ATTENTION ! Pour empêcher court-circuiter, fuite ou rupture de batterie : • • • • Utilisez les accumulateurs alcalins typiques d’AA seulement. Ne mélangez pas les types de batterie. N’essayez pas de recharger une batterie à moins que la batterie soit spécifiquement marqué « rechargeable ». Ne vous débarassez jamais des batteries dans un feu. Using the on-screen TV interface To use the on-screen TV interface with the remote: 1 Press the red Control4 button. The TV’s interface opens. 2 To navigate through the on-screen interface menus, press the directional buttons, and press the SELECT button to make your selection. Using the remote’s List interface To control devices from the remote control: 1 On the remote, press LIST to access the List interface. Lighting, Comfort, Security, and other options appear. 2 To navigate through the List interface and the Control4 system, press the arrow buttons to scroll through the menus, then press the SELECT button to make your selection. Using the WATCH and LISTEN buttons The WATCH button can be configured to quickly select the last video source watched or display a list of video sources for the room. The LISTEN button can be configured to quickly select the last audio source played or display a list of audio sources for the room. Changing selected rooms Depending on the room selected on your remote, the remote’s buttons may behave differently and the List interface may have different options. For example, with Living Room selected, the button may have been programmed to dim the lights, but with Theater selected, may turn them completely off. To change rooms on the remote: 1 Press List, then select Location > Floor > Room. Changing preferences To change the remote’s preferences: 1 Press LIST, then select Settings, then Config. • • • • • • To change the List interface’s brightness or the keypad brightness, select Display Brightness or Keypad Brightness, press the arrow buttons to adjust, then press SELECT. To change the remote’s sensitivity to motion (to wake it from sleep mode), select Motion Detect, then select the sensitivity level. To enable or disable the ambient light sensor, select Light Sensor, then select On or Off. To change the List interface’s text color, select Text Color, press the arrow buttons to pick the color, then press SELECT. To check the battery charge, select Battery Level. To return the remote’s preferences to factory defaults, select Factory Defaults. Regulatory and safety information To review regulatory information for your Control4 products, see ctrl4.co/reg. Warranty Limited two-year warranty. To review warranty details for your Control4 products, see www.control4.com/warranty. More help For the latest version of this document and to view additional materials, open the URL below or scan the QR code. LATEST VERSION ctrl4.co/sr260-ug MORE SR-260 DOCUMENTS ctrl4.co/sr260 help.control4.com Copyright ©2019, Control4 Corporation. All rights reserved. Control4, Pakedge, Triad, and their logos are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. 4Store, 4Sight, Control4 My Home, Mockupancy, and BakPak are also registered trademarks or trademarks of Control4 Corporation. Other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. C 200-0405-C 2019-05-09 MS
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021