NR-P101E-TQ, NR-P401E-TQ

Gigabit PoE Extenders

Manual

NR-P401E-TQ

NR-P101E-TQ

Features:

•

Extends the range of PoE Ethernet devices over Cat5e or higher cables an additional

328ft (100m)

•

Connects 10,100,1000BaseT PoE devices including IP cameras, IP access control,

VOIP, IP speakers/intercoms, etc.

•

Supports up to gigabit transmission rates

•

Passive operation – no external power required

•

Easy plug-and-play installation

•

Compliant with IEEE802.3af, IEEE802.3at

•

Automatically detects PoE equipment and protects from damage due to faulty installation

NR-P401E-TQ

•

4 Output ports for up to 4 PoE devices

•

Also compliant with IEEE802.3bt 4 pairs

®

ENFORCER Gigabit PoE Extenders

Introduction:

The ENFORCER Gigabit PoE Extenders connects PoE cameras, IP access control, IP telephony,

IP speakers/intercoms, or other PoE devices using a single Cat5e or Cat6 cable to extend its data and power range by an additional 328ft (100m). The NR-P401E-TQ supports up to 4 PoE devices.

Parts List:

1x PoE Extender*

2x Plastic wall anchors

2x Wall-mount brackets 2x Wall mounting screws

4x Extender bracket mounting screws 1x Manual*

*NR-P101E-TQ includes only the PoE extender with end caps and manual

Specifications:

Model

Connections

PoE Power

Transmission range*

Data link

Power link

Network cables

Ethernet speed

PoE standard

PoE In

PoE Out

Input

Output

1 Extender

2 Extenders

Power link

LED

Indicators

Data link

Data Transmit

IP rating

Operating humidity

Operating temperature

Dimensions

Weight

NR-P101E-TQ

1x Weather-resistant RJ-45

1x Weather-resistant RJ-45

Up to 30W

NR-P401E-TQ

1x Shielded RJ-45

4x Shielded RJ-45

Up to 60W

Up to 25W

656ft (200m)

Up to 55W (total for 4 ports)

656ft (200m)

984ft (300m)

Both pin 1/2, 3/6 and 4/5, 7/8

984ft (300m)

Pin 1/2(+), 3/6(–) up to 25W

Pin 1/2(+), 3/6(–) up to 12W for 4 PSE, 25W for 2 PSE

Weather-resistant Cat-5e or higher Shielded Cat-5e or higher

10/100/1000 Mbps half/full duplex

IEEE 802.3af, IEEE 802.3at

IEEE 802.3af, IEEE 802.3at,

IEEE 802.3bt 4 pairs (60W)

Yellow

None

IP66 (with weather-resistant UTP cable)

90% (maximum, non-condensing)

-13°~101° F (-25°~55° C)

7 1 /

4

"x1 3 /

4

"x1 3 /

4

" (185x45x45 mm) ‡

8-oz (227g)

4 11 /

16

Green, steady

Green flashing

None †

14°~113° F (-10°~45° C)

"x1 1 /

8

"x3 3 /

8

" (119x28x85 mm)

8.8-oz (250g)

*The maximum range depends on the actual operating conditions, PoE device power requirements, and the type of PoE device. Cat5e/6 Ethernet cables are recommended.

† The NR-P401E-TQ can be used outdoors with an IP66 sealed box and weather-resistant UTP cables

‡ Including endcaps

2 SECO-LARM U.S.A., Inc.

ENFORCER Gigabit PoE Extenders

Overview

NR-P101E-TQ NR-P401E-TQ

IN

Gigabit PoE Extender

OU T

1 3 /

4

"

(45mm)

3 3 /

8

"

(85mm)

7 1 /

4

" (185mm)

PoE In

Mounting tabs

PoE Out

1 3 /

4

"

(45mm)

1 1 /

8

"

(28mm)

Bracket mounting holes

4 11 /

16

" (119mm)

Gigabit PoE

Extender

PoE Link/Act

1

IN OU T

2 PoE OU T 3 4

Power Li nk/Act

PoE IN

PoE

Out

PoE

In

Installation:

1.

Determine the proper location for mounting the extender between the PoE power source and the PoE camera, ensuring that neither cable exceeds 328ft (100m) in length.

2.

Mount the NR-P101E-TQ using 4 screws (not included) and the mounting tabs.

3.

For the NR-P401E-TQ, attach the two mounting brackets to the extender, using the 4 included extender bracket mounting screws. Drill holes and attach the extender/bracket assembly to the wall or other desired location using the two wall mounting screws and, if needed, the plastic wall anchors.

4.

Ensure that power is off to the PoE power source and all PoE devices.

5.

Connect the cables from the PoE power source to the PoE In port of the extender.

6.

Connect the cables from the PoE cameras to the PoE Out port of the extender.

7.

Turn on the PoE power source and wait up to one minute for the devices to start and establish connections.

8.

Test to ensure that all devices are working properly.

Sample CCTV Application:

PoE Extender

(NR-401E-TQ shown)

Cat5e/6 cable up to

328ft (100m)

Cat5e/6 cable up to

328ft (100m) PoE source

PoE Cameras or other PoE devices

SECO-LARM U.S.A., Inc. 3

ENFORCER Gigabit PoE Extenders

Troubleshooting:

PoE device doesn't function properly

•

Ensure that all devices are turned on

•

Ensure that the PoE device is functioning by plugging it directly into the PoE switch, computer, etc.

•

Double-check that the cables were connected properly

•

Run a continuity test on all wires in the cable

•

Equipment at both ends must be at the same link speed,

10BASE-T with 10BASE-T, 100BASE-T with 100BASE-T, etc.

•

Replace with a higher-grade cable for better performance

•

Ensure that the cable lengths are within the allowable range and consistent with the remote PoE device power consumption, and reduce cable length as needed

•

With 1000BASE-T, power consumption is greater, so no more than 2 PoE extenders may be used

•

Check that power consumption is within the specifications

IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.

FCC COMPLIANCE STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A., Inc. All rights reserved.

SECO-LARM

® U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com

PICSN7

Phone: (949) 261-2999 | (800) 662-0800 Email: [email protected]

4

MI_NR-Px01E-TQ_200316.docx

SECO-LARM U.S.A., Inc.