Honda Crosstour 2013 Owner Manual

Add to My manuals
153 Pages

Honda Crosstour is an advanced navigation system designed to provide you with a seamless and intuitive driving experience. With its comprehensive features and user-friendly interface, the Honda Crosstour empowers you to navigate unfamiliar roads, discover new places, and stay connected while on the go.

advertisement

Honda Crosstour 2013 Owner Manual | Manualzz

20 1 3 Crosstour

Navigation Manual

(Unlinked)

This document does not contain hyperlinks and may be formatted for printing instead of web use. This is due to changes in content and specifications of the vehicle that happen throughout the model year. This manual will be replaced with a hyperlinked version at the end of the model year.

© 2012Honda Motor Co., Ltd.

P/N 00X31-TP6-8300

The information and specifications included in this publication were in effect at the time of approval for printing. Honda Motor Co., Ltd., reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring any obligation.

Accessories Precautions

The GPS antenna is located in the dashboard. Metallic front or side window tinting can seriously degrade or obstruct GPS reception.

Signal noise from devices such as radar detectors, vehicle tracking devices, remote starters, and additional amplifiers can disrupt the navigation system. If you install any such item, install it away from the navigation display and antenna.

Important Safety Information

WARNING

Using the navigation system while driving can take your attention away from the road, causing a crash in which you could be seriously injured or killed.

Only operate system controls when the conditions permit you to safely do so.

Avoid focusing on the screen or manually operating the system controls while driving.

Enter information before you begin driving or when stopped. As you drive, listen to the audible instructions and use voice commands when possible. Pull to the side of the road if you need more time to look at the screen or operate the controls.

Route guidance may conflict with street closures, road construction, detours, and out-of-date map data.

The system itself may also have limitations. Verify route information by carefully observing roads, signs, and signals. Always use your own judgment and obey

traffic laws.

2 System Limitations P. 130

2 System Setup P. 17

Start-up 18

Map 49

Personal Information 22

Routing 34

Guidance 42

2 Navigation P. 67

Entering a Destination 68

Changing Your Route 106

Calculating the Route 92

Driving to Your Destination 94

Map Menu 100

Changing Your Destination 115

Resuming Your Trip 118

2 Troubleshooting P. 119

Troubleshooting 120

Error Messages 126

2 Reference Information P. 127

System Initialization 128

System Limitations 130

2 Voice Commands P. 141

Voice Commands 142

Customer Assistance 132

Legal Information 135

Contents

Quick Reference Guide

P.2

System Setup

P.17

Navigation

P.67

Troubleshooting

P.119

Reference Information

P.127

Voice Commands

P.141

Index

P.149

2

Overview—Functions at a Glance

Navigation

You can select any place/landmark as a destination by using voice control or the Interface Dial. The navigation system gives you turn-by-turn driving directions to your destination.

Store home address

(P27)

Register

1

home address.

Store contacts

(P23)

Store up to

200

contacts in address book.

Enter destination

(P68)

Select your destination using

13

methods.

Address

Address Book

Place Category

Place Name

Previous Destination

Go Home

Place Phone Number

ZAGAT

Download POI

Scenic Route

Select route

(P93)

Set route preferences and select one of

3

routes.

Intersection

Map Input

Coordinate

Track route

(P94)

Follow your route in real-time with voice guidance.

FM Traffic

(P104)

Bypass congestion and traffic incidents.

Avoid certain areas

(P114)

Set streets and areas to detour around.

Add waypoints

(P108)

Add up to

4

“pit stops” along your route.

Voice Control

(P20)

Use voice commands to control the system while driving. You can operate all key functions of the navigation system.

Audio and Bluetooth ® HandsFreeLink® can be operated on this navigation system. See the Owner’s Manual for information on those systems.

3

System Controls

Navigation Screen

4

1

NAV Button

(P18)

2

BACK Button

3 a

(Display Mode)

Button

(P54)

4

MENU Button

(P68)

5

SETTINGS Button

6

Interface Dial/ENTER

Button

(P6)

Navigation

Voice Control

7

Microphone

(P20)

8 h

(Pick-Up) Button

9 J

(Hang-Up/Back)

Button

la d

(Talk) Button

(P5)

See the Owner’s Manual for other buttons.

Voice Control Operation

Voice Portal Screen

a Press and release the d

(Talk) button on the top screen of any mode.

The system prompts you to say a voice command and gives examples. Press and release the d

(Talk) button again to bypass this prompt.

 The system beeps when ready for a command. Press the

J

(Hang-Up/

Back) button to cancel.

 Available voice commands are highlighted on the screen.

b Say a voice command (e.g., Address).

After that, follow the voice prompt and say a voice command.

 The audio system is muted during voice control mode.

 You can use other voice commands on the Voice Portal screen. Voice Command

Index

(P142)

 Say d

“Voice Help” to enter supported commands for the current screen. A voice help tutorial is also available. Voice

Help (P20)

 During the voice control mode, press and hold the

J

(Hang-Up/Back) button to return to the Voice Portal screen.

 Set Voice Prompts to Off to bypass the voice prompt. See your Owner’s Manual.

 Carefully read the usage note for the voice control. Voice Control System

(P20)

On the Menu Screen

a Press and release the d

(Talk) button on the menu or setting screen.

The system prompts you to say a voice command and gives examples. Press and release the d

(Talk) button again to bypass this prompt.

Available voice commands are highlighted on the screen.

b Say a voice command.

 Say d

“Voice portal” to display the

Voice Portal on any screen.

 Say d

“Voice Help” to enter supported commands for the current screen. A voice help tutorial is also available. Voice Help

(P20)

5

Interface Dial/ENTER Button Operation

Rotate dial

i

Changes scale

Map screens

You will see these icons in each chapter.

They represent how you can operate the Interface Dial.

Press ENTER

Press ENTER

u

Selects function

Selects map icon

Map screens Rotate dial

6

Highlights menu options

Menu screens

Move up Move left Move down Move right

Move

e

up

r

down

w

left

y

right

Scrolls map

(8 directions)

Map screens

Selects labeled function

Menu screens

Selecting Icon

Selects highlighted option

Menu screens

How to Enter Information

You can enter information (e.g., city names, street names, personal names, and business names comprising letters, numbers, and symbols) when prompted on input screens by two different methods.

Using Voice Control

When you see d

in this manual, voice commands are available for that feature.

 Say the letter, number, or symbol (e.g., say d

“A” ).

 Use spelling assist (e.g., say d

“Alpha” to enter the letter “A” or d

“Hyphen” to enter a hyphen).

 The system beeps if you say an unavailable (grayed out) letter or number.

 If a voice command is not recognized, a list is displayed with possible options.

Using the Interface Dial

Rotate i

to highlight a character.

 Select to display upper/lower case characters.

 Select Sym to display symbols and accented characters.

 Select Edit (or move e

) to edit the entered characters.

Press u

to enter the highlighted character.

 Move y

to select Space to enter a space character.

 Move w

to select Delete to remove the last entered character.

Number of Hits

On list screens:

 Say the number of the list item (e.g., say d

“Five” to select item

5).

 Say d

“Up” or d

“Previous” to scroll up one page.

 Say d

“Down” or d

“Next” to scroll down one page.

On input search screens, the number of hits in the map database is displayed. Move r

to select OK to display a list of possible entries.

 You can also use the touch screen to enter information.

Scrolling through lists or tabs is limited while the vehicle is moving.

Certain screen functions are limited or inoperable while the vehicle is moving. For these functions, use available voice commands or pull over to proceed.

7

8

Map Screen Legend

Current map scale

Map orientation

(P56)

North up

Heading up

3D map

GPS signal strength

Best reception

Good reception

No icon: Poor/No reception

Map scale (P60)

Feature areas

Park

Hospital

Shopping Mall

Golf Course

Airport/Business

Water Area

Cemetery

University

Traffic status indicator (P104)

Traffic information availabled

Traffic information off or map scale too large

No icon: Out of coverage area

Traffic incident icons (P104)

Congestion

Incident

Weather

Construction

Road Closed

Current vehicle position

(P58)

Current street name

Traffic flow indicator (P104)

Heavy (approx.) surface: 0 to 20 mph freeway: 0 to 25 mph

Moderate (approx.) surface: 21 to 30 mph freeway: 25 to 52 mph

Free-flow (approx.) surface: 31+ mph freeway: 53+ mph

Streets

Freeways

State routes

Verified streets

Unverified streets

One-way streets

Landmark icons (P51)

Acura dealer

Honda dealer

ATM

School

Parking lot

Parking garage

Grocery store

Hotel/Lodging

Gas station

Hospital

Post office

Restaurant

Freeway exit information

During Route Guidance

During route guidance, route information is displayed on the map screen and guidance screen.

Press the NAV button to toggle between the map and guidance screen.

Map Screen

Tracking dots

(P97)

Guide to destination or waypoint

Estimated time to destination (waypoint)

Calculated route

(P94)

Next guidance indicator

Distance to the next guidance point.

Calculated route

(unverified roads)

(P96)

Distance to destination

(waypoint)

Distance of the actual route.

Guidance Screen

Waypoint

(P108)

Destination icon

Guidance point

Guidance indicator

Street name of guidance point and distance to the guidance point.

Guide to destination or waypoint

Estimated time to destination (waypoint)

Distance to destination

(waypoint)

Distance of the actual route.

Lane guidance

Guidance point

No entry icon

Map Menu

Contains map or routing options.

Day or Night Mode

Press the a

(Display mode) button to manually switch between day and night mode.

Day mode Night mode

9

10

Navigation—Home Addresses and Going Home

The “Home” feature automatically routes you to your home address from any location simply by selecting Go Home, or saying d

“Go

Home.”

Storing Your Home Address Going Home

e Enter a name.

a Press the SETTINGS button.

a From the map screen, press the MENU button.

b Rotate i

to select Navi Settings .

Press u

.

b Rotate i

to select Go Home . Press u

.

f Rotate i

to select Address . Press u

.

g Enter an address.

h Rotate i

to select Phone No . Press u

.

i Enter a phone number.

c Rotate i

to select Edit Go Home .

Press u

.

d Rotate i

to select Name . Press u

.

j Move r

and rotate i

to select OK .

Press u

.

Alternatively, you can say d

“Go

Home” from any screen. Your home address is displayed on the Calculate

Route screen.

c Rotate i

to select Set as

Destination . Press u

.

 The following voice commands are available: say d

“Go Home .

Navigation—Entering a Destination

Enter your destination using one of several methods, then follow route guidance on the map or guidance screen to your destination. You can also perform these steps using d

voice control.

a From the map screen, press the MENU button.

b Rotate i

to select Address . Press u

.

e Rotate i

to select your destination street from the list. Press u

.

h Rotate i

to select Set as

Destination . Press u

.

Route guidance to the destination begins.

c Rotate i

to select Street . Press u

.

f Enter the street number. Move r

to select OK when finished.

 View Routes : Choose one of three routes.

d Enter the name of your destination street.

g If there is more than one city with the specified street, a list of cities is displayed. Rotate i

to select the desired city from the list. Press u

.

 Route Preference : Choose Max or Min for the five settings.

11

12

Navigation—Changing Route or Destination

You can alter your route by adding waypoints to visit, adding streets to avoid, or changing your destination during route guidance.

Adding a Waypoint

(“Pit Stop”)

You can add up to four waypoints along

your route. (P108)

a From the map screen, press the MENU button.

b Rotate i

to select Destination List .

Press u

.

c Rotate i

to select Add New

Destination . Press u

.

d Rotate i

to select Find Along Route .

Press u

.

e Rotate i

to select location and search method. Press u

.

 Search Around : Search around a location.

 Search Along : Search between two locations.

f Select the icon category and location to add to the Destination List when prompted. Edit the order of destinations if necessary.

g Move r

and rotate i

to select Start

Route . Press u

.

Changing Your

Destination

There are four methods you can use to specify a new destination during route guidance.

 Say d

“Find Nearest…”

(P115)

Searches for the nearest place/landmark on the map screen (e.g., d

“Find nearest gas station” ).

 Say d

“Go Home”

(P10)

Routes to your home address.

Selecting an icon on the map

(P116)

Scroll the map to position the cursor over a place/landmark icon or a new area on the map. Press u

twice.

 Entering a new destination

(P117)

Press the MENU button. Move w

to select Destination and enter a new destination.

Canceling Your Route

a Press the MENU button.

b Rotate i

to select Cancel Route .

Press u

.

From the map screen:

a Press u

on the map screen.

b Rotate i

to select Cancel Route .

Press u

.

Voice Help

This navigation system comes with voice help, which shows you what command to say when using the voice command functions.

Command Help

a Press and release the d

(Talk) button.

b Say d

“ Voice Help.” e Press and release the d

(Talk) button.

f Say one of the options for a list of available commands by category (e.g., d

“Route commands” ).

Getting Started Tutorial

a Move r

and rotate i

to select

Getting Started on the voice help screen. Press u

.

The voice help screen is displayed.

The d

“Voice Help” command is available on most screens.

c Press and release the d

(Talk) button.

d Say one of the options for a list of available commands by category (e.g., d

“Navi commands” ).

g The system displays a list of all available commands for the category.

Press ( d

) to hear the list read aloud.

For “Voice Settings” and “All

Commands,” see your Owner’s Manual.

b Press u

to have the system read the tips for the voice control.

 Rotate i

to read the tips.

 Move w

or y

to display the previous/ next page.

13

14

Troubleshooting

Why does the vehicle position icon on the map “lag” a short distance behind my actual position, especially at intersections?

This is normal. The navigation system is unaware of the width of intersections. Large differences in vehicle position can indicate a temporary loss of the GPS signal.

Why does the “time to destination” display sometimes increase even though I am getting closer to my destination?

The “time to destination” is based on your actual road speed and traffic conditions to give you a better estimate of arrival time.

How do I specify a destination when an entered city or street could not be found?

Try entering the street first. Some cities are lumped in with a major metro area. In rural “unverified” areas or new subdivisions, streets may be missing or only partially numbered.

For more Information

(P119)

How do I turn on the navigation system voice guidance?

1.

Press the SETTINGS button. Rotate i

to select System

Settings and press u

. Check that Volume is not set to

Off .

2.

Move w

or y

to select Voice Rec.

Set Voice Prompt to On if you want the system to provide confirmations and system prompts.

My battery was disconnected or went dead, and the navigation system is asking for a code. Where do I find it?

In most cases, you do not need to enter a code. Simply press and hold the PWR

9

(Power) button for two

seconds; the system should reactivate.

2 System Initialization P. 128

How to Use This Manual

This section explains different methods on how you can easily find information in this manual.

Searching the Table of Contents

(P1)

Two types of Tables of Contents help you find your desired information.

Content s

More Detaile d

Contents

Table of Contents

First, find the general chapter related to what you are looking for (e.g., entering a destination from the Address Book).

Then, go to that chapter to view a more specific table of contents.

Chapter Contents

This more detailed table of contents shows you exactly what information is listed by section and title.

Searching the Index

(P149)

Menu items displayed on the navigation screen (e.g., Address Book) can be found individually in the Index.

Navigation Screen Index

The Index consists of main terms and sub-entries. The sub-entries help you get to the desired page depending on what you are looking for.

Go to the

Next Pa g e

15

After following the menu tree, step-by-step instructions explain how to achieve the desired result.

16

Menu Tree

The menu tree helps guide you through the system’s menu options.

To get to your desired function, follow the menu tree in order of the steps shown.

NOTE:

All menu options can also be activated with voice commands.

MENU button

Press the hard button on the system control panel.

Press the MENU button.

Sample pages and images in this section may differ from the actual ones.

Select the menu option with the

Interface Dial.

Rotate i

to select Address Book .

Press u

.

System Setup

This section describes the start-up procedure and the navigation and setup functions.

Start-up ................................................... 18

Voice Control System ............................. 20

Command Input .................................... 20

Voice Recognition .................................. 21

Personal Information .............................. 22

Address Book......................................... 23

Home Address ....................................... 27

PIN Numbers .......................................... 28

Previous Destination............................... 29

Category History .................................... 30

Download POI........................................ 31

Routing .................................................... 34

Route Preference.................................... 35

Unverified Routing ................................. 36

Traffic Rerouting .....................................38

Edit POI Search Radius Along Route ........39

Avoided Area ..........................................40

Guidance ..................................................42

Guidance Mode ......................................43

Street Name Guidance ............................45

Next Maneuver Pop up ...........................46

Guidance Point .......................................47

Estimated Time .......................................48

Map ...........................................................49

Showing Icons on Map ...........................51

Color ......................................................53

View (Map Orientation)...........................56

3D Angle Adjustment .............................57

Straight Line Guide ................................ 57

Current Location .................................... 58

Map Legend........................................... 59

Display Tracking ..................................... 63

Correct Vehicle Position ......................... 64

System Device Information ..................... 65

Map Data Update .................................. 65

17

18

Start-up

The navigation system starts automatically when you set the power mode to

ACCESSORY or ON. At start-up, the following Confirmation screen is displayed.

1.

Press u

to select OK .

 If you do not select OK , the map screen is displayed after a certain period of time.

 Your current position is displayed on the map screen.

1 Start-up

If the navigation system loses power at any time, you may need to press and hold the PWR

9

(Power) button for more than two seconds, or you may be prompted for the five-digit security code.

2 System Initialization P. 128

“OK” on the Confirmation screen cannot be selected by using a voice command.

2.

Press the NAV button when a different mode is selected.

 Your current position is displayed on the map screen.

Limitations for Manual Operation

Disabled option

Certain manual functions are disabled or inoperable while the vehicle is in motion. You cannot select a grayedout option using the Interface Dial until the vehicle is stopped.

Voice commands are still operable while the vehicle is in motion.

 Start-up 

19

20

Voice Control System

Your vehicle has a voice control system that allows hands-free operation of most of the navigation system functions.

The voice control system uses the d

(Talk) and

J

(Hang-Up/Back) buttons on the steering wheel and a microphone near the map lights on the ceiling.

A “Getting Started” feature provides a tutorial that explains how to use the voice

control system.

2 Getting Started Tutorial P. 13

Command Input

If the system does not understand a command or you wait too long to give a command, the system asks you to repeat the command.

When you give a command, the system generally either repeats the command as a confirmation or asks you for further information. If you do not wish to hear this feedback, you can turn it off. However, listening to the feedback will help familiarize you with the way the system expects commands to be phrased.

If the system cannot perform a command or the command is not appropriate for the screen you are on, the system beeps.

On character input screens, a list of possible characters is displayed if the system does not recognize your command.

You can find out which voice commands are available for a particular screen using the d

“Voice Help” command. The system will display and read the list of available commands to you.

2 Voice Help P. 13

1 d

(Talk) Button

When you press the d

(Talk) button, the system prompts you to say a voice command and gives examples. Press and release the d

(Talk) button again to bypass this prompt and give a command.

1 Command Input

The audio system is muted while using the voice control system.

 Voice Control System  Voice Recognition

Voice Recognition

To achieve optimum voice recognition when using the navigation voice control system:

• Make sure the correct screen is displayed for the voice command that you are using.

2 Voice Commands P. 142

• Close the windows and moonroof.

• Adjust the dashboard and side vents so air does not blow onto the microphone on the ceiling.

• Speak clearly in a clear, natural speaking voice without pausing between words.

• Reduce any background noise if possible. The system may misinterpret your command if more than one person is speaking at the same time.

• Refer to the Voice Help feature.

2 Voice Help P. 13

1 Voice Recognition

The voice control system can only be used from the driver’s seat because the microphone unit removes noises from the front passenger’s side.

21

Personal Information

H

SETTINGS button  Navi Settings  Personal Info

Use the personal information menu to select and set your address books, home addresses, and PINs. You can also delete unwanted destinations from the list of previously routed destinations.

Rotate i

to select an item. Press u

.

1 Personal Information

Personal information cannot be backed up or moved to another navigation system.

22

The following items are available:

• Address Book : Stores new addresses or edits your address book.

2 Address Book P. 23

• Edit Go Home : Sets or edits your home address.

2 Home Address P. 27

• PIN Number : Sets or changes your PIN.

2 PIN Numbers P. 28

• Previous Destination

: Deletes the destination history.

2 Previous Destination P. 29

• Category History : Deletes the place categories you recently used.

2 Category History P. 30

• Download POI : Edits and deletes the Imported POI categories.

2 Editing POI Categories P. 32

 Personal Information  Address Book

Address Book

H

SETTINGS button  Navi Settings  Personal Info  Address Book

Store up to 200 address entries in the address book. You can add, edit, and delete information in the address book.

Move w

or y

to display only the addresses in the selected category.

1 Address Book

If you have PIN-protected your address book, enter your PIN when prompted. Press u

to select OK

. PINs are optional.

2 PIN Numbers P. 28

Any address book categories you create are also

displayed.

2 Selecting an Address Book Category P. 26

Adding an Address Book Entry

H

SETTINGS button  Navi Settings  Personal Info  Address Book

This section explains how to enter the name and address.

1.

Move r

and rotate i

to select

Add New Address . Press u

.

1 Adding an Address Book Entry

If you do not give the address a name, one is automatically assigned (e.g., Address 001). You can re-enter, edit, or make changes to any entry.

“Address” is the only required field.

Continued 23

 Personal Information  Address Book

2.

Rotate i

to select an item. Press u

.

24

The following items are available:

• Name : Edits the name of the entry.

• Address : Edits the address of the entry.

• Phone No.

: Edits the phone number of the entry.

• Category : Specifies the category of the entry.

• Alert : Alerts you when you approach the address entry.

On : Beeps and displays a message when your vehicle gets near the entry.

Off (factory default): Disables the feature.

3.

Rotate i

to select Name . Press u

.

4.

Enter a name or title. Move r

to select OK .

5.

Rotate i

to select Address . Press u

.

6.

Rotate i

to select an item for specifying the address. Press u

.

 Personal Information  Address Book

The following items are available:

• Current Position: Select your current location.

• Address:

Enter an address on the character input screen when prompted.

2 Address P. 70

• Previous Destinations:

Select a previous destination.

2 Previous Destination P. 77

• Place Name:

Enter the name of a place/landmark.

2 Place Name P. 80

• Place Category: Select a category to search for a place/landmark (e.g., Banking,

Lodging).

2 Place Category P. 78

• More Search Methods

: Displays additional search method entries.

2 Entering a Destination P. 68

Editing an Address Book Entry

H

SETTINGS button

 Navi Settings  Personal Info  Address Book

1.

Rotate i

to select the address to edit. Press u

.

2.

Enter the name, address, phone number, and category fields.

2 Adding an Address Book Entry

P. 23

3.

Move r

and rotate i

to select

OK . Press u

.

1 Adding an Address Book Entry

When you use Place Name or Place Category , the phone number is automatically entered.

You can also add a phone number and category.

1 Editing an Address Book Entry

The entered contents are displayed on the Edit address screen.

Continued 25

26

 Personal Information  Address Book

Selecting an Address Book Category

H

SETTINGS button

 Navi Settings  Personal Info  Address Book

1.

Rotate i

to select an address.

Press u

.

2.

Rotate i

to select Category .

Press u

.

3.

Rotate i

to select a category.

Press u

.

Create a category in advance.

2 Creating a New Category P. 26

■ Creating a New Category

1.

Move r

and rotate i

to select New Category . Press u

.

2.

Enter a name and select an icon when prompted.

 The created category is displayed in the list of categories.

■ Deleting or Editing a Category

1.

Move r

and rotate i

to select Delete or Edit . Press u

.

2.

Delete an existing category, or change the name and icon.

 The selected category to delete is indicated with a trash icon. Move r

and rotate i

to select OK .

1 Selecting an Address Book Category

You can have up to 100 categories (including

“Unfiled”).

If you delete a category that is used by other addresses, the category type for those addresses changes to “Unfiled.”

 Personal Information  Home Address

Deleting an Address Book Entry

H

SETTINGS button

 Navi Settings  Personal Info  Address Book

1.

Rotate i

to select the address to delete. Press u

.

2.

Move r

and rotate i

to select

Delete . Press u

.

3.

Rotate i

to select Yes . Press u to delete the address.

1 Deleting an Address Book Entry

When you transfer the vehicle to a third party, delete all address book entries.

Home Address

H

SETTINGS button

 Navi Settings  Personal Info  Edit Go Home

Set home address that you frequently use.

1.

Edit the name, address, and phone number the same way as an

address in the address book.

2 Adding an Address Book Entry

P. 23

2.

Move r

and rotate i

to select

OK . Press u

.

1 Home Addresses

If you have PIN-protected your home addresses, enter your PIN when prompted. Press u

to select OK . PINs are optional.

2 PIN Numbers P. 28

If your home street is not in the system database, park on the nearest verified street to your home.

When entering the “Address” field, rotate i

to select Current Position to use your current location as the home address and press u

.

You can delete a home address if necessary.

Move r

and rotate i

to select Clear Home

Entry . Press u

. Rotate i

to select Yes . Press u

.

When you transfer the vehicle to a third party, delete all home addresses.

The home icon is shown on the map screen on the 1/20 and 1/8 mile scales.

27

28

 Personal Information  PIN Numbers

PIN Numbers

H

SETTINGS button  Navi Settings  Personal Info  PIN Number

Set a four-digit PIN for protecting personal addresses and your home address. Once you set a PIN, you are prompted to enter it whenever you access a personal address or a home address.

1.

Rotate i

to select the PIN to create. Press u

.

1 PIN Numbers

PIN

Personal Identification Number (PIN) is a password used to access personal data.

PINs are optional. If you choose to use a PIN, keep a note of the number in a secure location. If you forget your PIN, a dealer will have to reset the navigation system and all of your stored information will be erased. The factory default is no PIN.

If you want to stop using a PIN, move

Turn off PIN entry . Press u

.

r

to select

2.

Rotate i

to select a digit to enter. Press u

to select OK .

Repeat to enter a new four-digit

PIN.

3.

Re-enter the new PIN, when prompted, to confirm the number you just entered. Press u

to select

OK .

If you have not entered the same number both times, an

“INCORRECT PIN” message is displayed. Enter your PIN again.

 Personal Information  Previous Destination

Previous Destination

H

SETTINGS button  Navi Settings  Personal Info  Previous Destination

The navigation system maintains a list of your previously routed destinations as a shortcut for entering the same destination in the future. You can delete some or all of your previous destinations from the list.

1.

Rotate i

to select the destination to delete. Press u

.

 Repeat the procedure as necessary.

 Items to be deleted are indicated with a trash icon.

1 Previous Destinations

Up to 50 destinations can be stored.

To cancel the selection of a previous destination, rotate i

to highlight the destination again.

Press u

to de-select it.

2.

Move r

and rotate i

to select

OK to delete the selected destinations.

Trash icon

29

30

 Personal Information  Category History

Category History

H

SETTINGS button  Navi Settings  Personal Info  Category History

The navigation system maintains a list of your recently used place categories as a short cut for selecting the same categories in the future. You can delete some or all of your recently used categories from the list.

1.

Rotate i

to select the category to delete. Press u

.

 Repeat the procedure as necessary.

 Items to be deleted are indicated with a trash icon.

1 Category History

Up to 50 categories can be stored.

To cancel the selection of a category, rotate i to highlight the category again. Press u

to deselect it.

2.

Move r

and rotate i

to select

OK to delete the selected categories.

Trash icon

Download POI

Import custom Points of Interest (POI) into the navigation system and set the POI as a destination. You can also add, edit, and delete POIs.

 Personal Information  Download POI

Importing POI Categories

H

MENU button (on map)

 More Search Methods  Download POI

1.

Connect a USB flash drive with stored POI data to the USB connector.

2.

Move r

and rotate i

to select

Import from USB . Press u

.

1 Importing POI Data

For more information about connecting a USB flash drive, see your Owner’s Manual.

POI data in csv and kml formats can be imported.

You can download POI data from various POI websites.

Continued 31

32

 Personal Information  Download POI

3.

Rotate i

to select a category to import. Press u

.

Editing POI Categories

H

SETTINGS button  Navi Settings  Personal Info  Download POI

1.

Rotate i

to select the downloaded POI category to edit.

Press u

.

2.

Rotate i

to select an item. Press u

.

The following items are available:

• Alert Setting : Alerts you when you approach the places/landmarks in the category.

On : Beeps and displays a message when your vehicle gets near the places/ landmarks in the category.

Off (factory default): Disables the feature.

• Delete Category : Deletes all places/landmarks and icon in the selected category.

• Edit Icon : Changes the category icon.

 Personal Information  Download POI

33

Routing

H

SETTINGS button  Navi Settings  Routing

Choose various settings that determine the navigation system functionality during route calculation.

Rotate i

to select an item. Press u

.

34

The following items are available:

• Route Preference : Changes the route preferences (calculating method).

2 Route Preference P. 35

• Unverified Routing : Sets whether you use the route guidance in unverified areas.

2 Unverified Routing P. 36

• Traffic Rerouting : Sets whether you use automatic recalculation based on traffic

information.

2 Traffic Rerouting P. 38

• Edit POI Search Radius Along Route : Sets the distance from the route to find

waypoints.

2 Edit POI Search Radius Along Route P. 39

• Avoided Area

: Specifies areas to avoid when calculating a route.

2 Avoided Area P. 40

 Routing  Route Preference

Route Preference

H

SETTINGS button  Navi Settings  Routing  Route Preference

Change the route preference by selecting minimum or maximum driving methods.

1.

Rotate i

to select an item. Press u

.

2.

Rotate i

to select Min or Max .

Press u

.

 Repeat step 1 and 2 as necessary.

3.

Move r

to select OK . Press u

.

1 Route Preference

The calculated route may be the shortest route or the route you would choose. For safety reasons, the system generally applies the following rules to your route:

Shortcuts through residential areas are avoided.

• Right turns are favored over left turns or Uturns.

Time-restricted turns (turns prohibited at certain times of the day) are not used.

Check the ferry schedule when the calculated route includes ferry route.

ETC is short for the Electronic Toll Collection system.

35

36

 Routing  Unverified Routing

Unverified Routing

H

SETTINGS button  Navi Settings  Routing  Unverified Routing

Receive turn-by-turn map and voice guidance in unverified areas.

Rotate i

to select On or Off . Press u

.

1 Unverified Routing

Unverified roads are found in rural areas, and typically include residential streets away from the center of a town. They may not be accurate, and can contain errors in location, naming, and address range.

Unverified roads are shown only when viewing the map in the 1/20, 1/8, or 1/4 mile map scales.

Straight line guide

Differences

Route line

Off

On or Off?

The driver wishes to manually navigate using the navigation map

Route calculation and choose the streets that lead to the destination.

Route is usually longer, using verified roads whenever possible.

The route line uses verified streets only (when possible).

If Straight Line Guide is set to On , a pink vector line is displayed on the map that continually points to your

destination.

2 Straight Line Guide P. 57

On (factory default)

The driver chooses to let the navigation system suggest possible routing, knowing that the guidance may not be accurate.

Route is shorter, but uses unverified (purple) streets that may not be accurate.

A blue-pink route line highlights suggested unverified streets on the map while traveling to your destination.

Blue-pink route line

Differences

Cautionary messages

Guidance

(map/voice)

Directions list

Off

Cautionary pop-up screens and voice announcements remind you to obey all traffic restrictions when starting route guidance, approaching an unverified area, and entering an unverified street.

There is no turn-by-turn map or voice guidance.

A direction list is typically not available. However, depending on your route, directions are provided to help you reach the first available verified road.

On (factory default)

Cautionary pop-up screens and voice announcements remind you to obey all traffic restrictions when entering an unverified street.

Voice guidance commands end with the phrase “if possible” to remind you to verify all traffic restrictions.

A direction list is provided showing street names and turn symbols in pink.

 Routing  Unverified Routing

37

38

 Routing  Traffic Rerouting

Traffic Rerouting

H

SETTINGS button  Navi Settings  Routing  Traffic Rerouting

A faster route can be calculated based on continuously updated traffic information.

2 Traffic Rerouting™ P. 104

Rotate i

to select an option. Press u

.

1 Traffic Rerouting

You must be in or near a traffic-enabled city to receive coverage for that area. FM Traffic is available in the lower 48 states, Canada and

Hawaii.

Automatic traffic rerouting may not provide a detour route depending on circumstances.

The following options are available:

• On : The system reroutes automatically based on traffic information.

• Off (factory default): Disables the feature.

 Routing  Edit POI Search Radius Along Route

Edit POI Search Radius Along Route

H

SETTINGS button  Navi Settings  Routing  Edit POI Search Radius

Along Route

Select the distance from your highlighted route line (on either side of your route) that the system will search for a waypoint.

2 Adding Waypoints P. 108

You can specify a different search distance for freeways and surface streets.

1.

Rotate i

to select an item. Press u

.

2.

Rotate i

to select a search distance. Press u

.

1 Edit POI Search Radius Along Route

The search distance does not affect the search range used for the Find Nearest voice commands

(e.g., say d

“Find nearest gas station” ).

The following items are available:

• On Freeways : 1, 2, 5, or 10 miles can be set. Factory default is 2 miles.

• On Surface Streets : 1/2, 1, 2, or 5 miles can be set. Factory default is 1/2 mile.

39

40

 Routing  Avoided Area

Avoided Area

H

SETTINGS button  Navi Settings  Routing  Avoided Area

Specify up to five areas to avoid (e.g., road construction, closures), if possible, when the system calculates routes to your destination.

1.

Move r

and rotate i

to select

New Area , or rotate i

to select an existing area to edit.

1 Avoided Area

The maximum size of an “avoid area” is approximately 1 square mile.

If your selected area contains a freeway, you are asked “Do you want to avoid freeways?”

Answering “No” allows you to use a route through an avoid area on a freeway without any pop-up messages.

You can select areas to avoid, however you cannot select roads or areas that you want the system to use for routing.

You can enter up to 25 characters for the name.

2.

Rotate i

to select Name to label the area to avoid. Press u

.

3.

Enter a name or title. Move r

to select OK .

4.

Rotate i

to select Area to define the area to avoid. Press u

.

The following options are available (after an area is set):

• View Area : Displays the selected avoid area on the map.

• Delete : Deletes the selected avoid area.

 Routing  Avoided Area

5.

Rotate i

to select a method for specifying the area. Press u

.

1 Avoided Area

Avoid area can be set in the 1/20, 1/8, or

1/4 mile map scales.

The following options are available:

• Address : Specify the general area by entering an address.

2 Address P. 70

• Map Input

: Specify the general area by map input.

2 Map Input P. 89

Cursor

6.

If you select Map Input , scroll the map to position the cursor over your desired start point, adjusting the map scale as necessary. Press u

to mark the start point.

 To redo the area selection, press the BACK button.

7.

Scroll the map to “draw” the area.

Press u

to mark the end point.

8.

Press u

to select OK .

 The area you specify is displayed in the list of areas to avoid.

Avoid area

41

Guidance

H

SETTINGS button  Navi Settings  Guidance

Choose various settings that determine the navigation system functionality during route guidance.

Rotate i

to select an item. Press u

.

42

The following items are available:

• Guidance Mode : Sets whether to display only the map screen or a split mapguidance screen.

2 Guidance Mode P. 43

• Street Name Guidance : Sets whether to read out the street names during voice

guidance.

2 Street Name Guidance P. 45

• Next Maneuver Pop up : Sets whether the guidance screen interrupts the screen display.

2 Next Maneuver Pop up P. 46

• Guidance Point : Sets whether to display the guidance information to the

destination or the next waypoint.

2 Guidance Point P. 47

• Estimated Time : Sets whether to display the remaining time or arrival time to the

guidance point.

2 Estimated Time P. 48

 Guidance  Guidance Mode

Guidance Mode

H

SETTINGS button  Navi Settings  Guidance  Guidance mode

Select the display mode for the map and guidance screens.

Rotate i

to select an option. Press u

.

1 Guidance Mode

The guidance mode can also be selected from

the map menu.

2 Map Menu P. 100

Press the NAV button to switch between the map, next guidance direction, and a list of guidance directions.

The following options are available:

• Map (factory default): Displays only the map screen. When you approach a guidance point, the next guidance point appears.

Map screen Next Maneuver screen

Near the next guidance point

Next guidance point

Continued 43

44

 Guidance  Guidance Mode

• Direction List : Displays the map and direction list simultaneously on the map screen. When you approach a guidance point, the next guidance point appears.

Direction List screen Next Maneuver screen

Near the next guidance point

Guidance direction list Next guidance point

• Next Maneuver : Displays the map and next guidance point simultaneously on the map screen.

Next Maneuver screen Next Maneuver screen

Near the next guidance point

Next guidance point

 Guidance  Street Name Guidance

Street Name Guidance

H

SETTINGS button  Navi Settings  Guidance  Street Name Guidance

The navigation system includes the street names during voice guidance (e.g., “Turn right on Main Street”).

Rotate i

to select an option. Press u

.

1 Street Name Guidance

This feature is only available when the system language is set to English .

This feature may not be available in non-English speaking areas.

The following options are available:

• On (factory default): Voice guidance includes the street names.

• Off : Disables the feature.

45

 Guidance  Next Maneuver Pop up

Next Maneuver Pop up

H

SETTINGS button  Navi Settings  Guidance  Next Maneuver Pop up

The navigation system temporarily interrupts the screen display to view the guidance screen as you approach a guidance point.

Rotate i

to select an item. Press u

.

46

The following items are available:

• LaneWatch : Sets whether to view the guidance screen while displaying the

LaneWatch screen.

On (factory default): The guidance screen interrupts the LaneWatch screen.

Off : Disables the feature.

• Non-map Screens : Sets whether to view the guidance screen while displaying other mode (e.g., audio, phone, etc.) screen.

On : The guidance screen interrupts other mode screens (except the rear view mode).

Off (factory default): Disables the feature.

Guidance Point

H

SETTINGS button  Navi Settings  Guidance  Guidance Point

Set the guidance point to display on the map screen.

Rotate i

to select an option. Press u

.

The following options are available:

• Destination (factory default): Displays the remaining/arrival time and distance to the destination.

• Next Point : Displays the remaining/arrival time and distance to the next waypoint.

 Guidance  Guidance Point

47

48

 Guidance  Estimated Time

Estimated Time

H

SETTINGS button  Navi Settings  Guidance  Estimated Time

Select the estimated time to display on the screen.

Rotate i

to select an option. Press u

.

The following options are available:

• Arrival : Displays the arrival time to the destination or the next waypoint.

• Remaining (factory default): Displays the remaining time to the destination or the next waypoint.

Map

H

SETTINGS button  Navi Settings  Map

Select the landmark icons to display on the map, change the orientation of the map, display your current location, and learn the meaning of the icons, colors, and symbols displayed on the map.

Rotate i

to select an item. Press u

.

The following items are available:

• Show Icon on Map : Selects the icons to display on the map.

2 Showing Icons on Map P. 51

• Color (Day)

: Selects the color of the map for the Day mode.

2 Color P. 53

• Color (Night)

: Selects the color of the map for the Night mode.

2 Color P. 53

• View

: Selects the map orientation (North-up, Heading-up, or 3D map).

2 View (Map Orientation) P. 56

• 3D Angle Adjustment

: Adjusts the viewing angle for the 3D map.

2 3D Angle Adjustment P. 57

• Straight Line Guide : Sets whether to display a straight guideline to the destination or waypoint.

2 Straight Line Guide P. 57

Continued 49

50

 Map  Estimated Time

• Current Location : Displays and saves your current location.

2 Current Location P. 58

• Map Legend : Displays an overview of the map features.

2 Map Legend P. 59

• Display Tracking : Sets whether to display the tracking dots on the map.

2 Display Tracking P. 63

• Delete Tracking : Deletes the tracking dots on the map.

2 Deleting Tracking Dots P. 63

• Correct Vehicle Position : Adjusts the position of the vehicle on the map.

2 Correct Vehicle Position P. 64

• System Device Information : Views database, software, device, and vehicle identification information.

2 System Device Information P. 65

• Map Data Update : Checks the map data update status when updating the map database.

2 Map Data Update P. 65

 Map  Showing Icons on Map

Showing Icons on Map

H

SETTINGS button  Navi Settings  Map  Show Icon on Map

Select the icons that are displayed on the map.

1.

Rotate i

to select an item. Press u

.

1 Showing Icons on Map

You can display or hide the icons using voice commands on the Voice Portal screen (e.g., say d

“Display hospital”

).

2 Map Display Commands P. 142

The following options are available:

• All On

: Displays the landmark icons.

2 Map Screen Legend P. 8

• Customize

: Fine-tunes the icon display.

2 Fine-tuning the Icons P. 52

• Off : Hides the landmark icons.

2.

Rotate i

to select an option.

Press u

.

Repeat step1 and 2 as necessary.

3.

Move r

to select OK . Press u

.

Continued 51

52

 Map  Showing Icons on Map

Fine-tuning the Icons

Icons in some categories can be fine-tuned to display or hide.

1.

Rotate i

to select the icons to display on the map. Press u

.

Pressing u

toggles the icon display on or off.

 Repeat the procedure as necessary.

2.

Move r

and rotate i

to select

OK . Press u

.

 Map  Color

Color

Set separate map colors for Day and Night modes.

Color (Day)

H

SETTINGS button  Navi Settings  Map  Color (Day)

Rotate i

to select a color for the

Day mode. Press u

.

1 Color (Day)

Set to White (factory default is Beige ) to obtain the best daytime display contrast.

Color (Night)

H

SETTINGS button  Navi Settings  Map  Color (Night)

Rotate i

to select a color for the

Night mode. Press u

.

1 Color (Night)

Set to Black (factory default) to obtain the best nighttime display contrast.

Continued 53

54

 Map  Color

Switching Display Mode Manually

Set the screen brightness separately for Day and Night modes. Press the a

(Display mode) button to cycle through the display modes (Day to Night to Off).

1.

Press the a

button.

The Brightness bar is displayed for a few seconds.

 Rotate i

to adjust the brightness. Press u

.

2.

Press the a

button again.

Repeat the procedure to switch the display modes.

1 Switching Display Mode Manually

A visual guide helps you see the difference

between Day and Night modes.

2 Day or Night Mode P. 9

Recommended Settings

Select mid-range for the dash illumination.

Select White for the map Day display and

Black for the map Night display.

Illumination control a

button

Priority

Sunlight sensor

(see your

Owner’s Manual for location)

Dash illumination adjustment buttons (see your

Owner’s Manual for location)

Headlights

(Auto/On/Off)

Screen color choice

Operation

1

2

Selects Day, Night, or Off display mode. This button has the highest priority and overrides all other display control adjustments listed below.

Remember : Once you press this button, you assume full manual control of the display mode until the power mode is set to VEHICLE OFF (LOCK).

If the sunlight sensor detects daylight and the headlights are turned on, the system automatically overrides the

Night display and displays the Day display mode.

Remember : If desired, use the a

button to override this automatic choice.

3 When headlights are turned on, and you wish to have the

Day display mode, adjust the illumination to the full brightness setting (beeps).

Remember : Adjust the dash brightness back to mid-range to allow auto switching by sensing the headlights are on or off.

4 When turned on, the display changes to Night display mode. The previous three controls listed above can

“cancel” this function.

Remember : Use the a

button, or adjust the dash illumination to full brightness, to set the display to your desired choice.

N/A The user can select the color of the screen that will be displayed for the Day and Night display modes described above.

Remember : For best contrast, ensure that the map color is white for Day and black for Night.

 Map  Color

55

56

 Map  View (Map Orientation)

View (Map Orientation)

H

SETTINGS button  Navi Settings  Map  View

Select the map orientation.

Rotate i

to select an option. Press u

.

The following options are available:

• North-Up : Displays the map with North always pointing up.

• Heading-Up : Displays the map so that the direction you are traveling is always pointing up.

• 3D Map : Displays the bird’s eye view map.

1 View (Map Orientation) d

“Display Heading-up” (on Voice Portal screen), d

“Display North-up” (on Voice Portal screen), d

“Display 3D map” (on Voice Portal screen)

The red arrow in the symbol always points North.

Heading-up and 3D map view switch to the

North-up view on the maximum map scale.

The bird’s eye view map switches to the

Heading-up map while scrolling the map.

The viewing angle for the bird’s eye view can be adjusted.

2 3D Angle Adjustment P. 57

3D Angle Adjustment

H

SETTINGS button  Navi Settings  Map  3D Angle Adjustment

Adjust the viewing angle.

Rotate i

to adjust the angle. Press u

.

Straight Line Guide

H SETTINGS button  Navi Settings  Map  Straight Line Guide

Set whether to display a straight guideline to the destination or waypoint

Rotate i

to select an option. Press u .

The following options are available:

• On (factory default): Displays the straight guideline on the map.

• Off : Disables the feature.

 Map  3D Angle Adjustment

57

58

 Map  Current Location

Current Location

H

SETTINGS button  Navi Settings  Map  Current Location

Display and save your current location for future use as a destination. The address, latitude, longitude, and elevation of your current location are displayed.

■ To save your current location in the address book:

1.

Press

 u

Move

to select Address Book.

w necessary.

to scroll the map as

2.

Edit the name, phone number, and

category.

2 Address Book P. 23

3.

Move r

and rotate i

to select

OK . Press u

.

1 Current Location d

“Display Current Location” (on Voice Portal screen)

You can also save the current location by saying d

“Register the Current Location” .

If you have PIN-protected your address book, enter your PIN when prompted. Press u

to select OK . PINs are optional.

2 PIN Numbers P. 28

The elevation is not displayed if the system is receiving insufficient GPS information. When elevation is displayed, it may differ with roadside elevation signs by ±100 feet or more.

Saving your current location does not change or cancel your current route.

 Map  Map Legend

Map Legend

H

SETTINGS button  Navi Settings  Map  Map Legend

See an overview of the map lines, areas, routes, traffic information, and navigation icons.

Move w

or y

select an item.

 The system displays the map legend.

1 Map Legend

A visual guide helps you see the map legend.

2 Map Screen Legend P. 8

Continued 59

 Map  Map Legend

60

Map Scale and Functions

The functions that are available from the map screen depend on the map scale.

Function page 1/20 1/8

Map Scale (top: mile, bottom: metric)

1/4 1/2 1 2 5 15 50 150 350 1000

80 200 400 800 1.6

3.2

8 24 80 240 560 1600

Icon display

Landmark icon

Exit info.

One-way traffic

8

8

8

Waypoint

“flag”

9

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

✔ ✔ ✔ ✔ ✔ ✔ ✔ Traffic incident

Map orientation

8

Heading-up

North-up

56

56

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

3D map

Others

56

Tracking dots

97

Unverified road

8

Map features

Avoid areas

Traffic speed

8

40

8

✔ ✔ ✔

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

✔ ✔ ✔

✔ ✔ ✔ ✔ ✔ ✔ ✔

1 Map Scale and Functions

You can change the map scale using voice commands on the Voice Portal screen (e.g., say d

“Display 2 mile scale” ).

2 Map Scale Commands P. 142

You can change between miles or kilometers.

See your Owner’s Manual.

 Map  Map Legend

Map Icons and Functions

Display or hide all icons on the map screen, with the exception of Honda/Acura

Dealer icons which are always shown.

■ Landmark icon

Type

Honda/Acura dealer

Hospital

School

ATM

Gas station

Restaurants

Post office

Grocery store

Hotel/Lodging

Police station

Shopping, Tourist attraction, Bank

Parking garage

Parking lot

Freeway exit info.

Icon display control

Always on

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

No icon

No icon

Yes

Yes

Yes

No

Yes

Yes

Yes

Yes

Yes

Yes

No

Icon selectable

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

No

Yes

Yes

Yes

Yes

Icon searchable

Yes

Yes

Yes

Yes

Yes

Yes

1 Map Icons and Functions

You can display or hide the icons using voice commands on the map screen (e.g., say d

“Display hospital”

).

2 Map Display Commands P. 142

Some icons, like police stations, are not shown, but you can still locate the nearest one with the

Find Nearest voice command (e.g., say d

“Find nearest police station” ).

2 Find Place Commands P. 143

Icon display control

Icons that can be displayed or hidden using the

Interface Dial or voice command.

Icon selectable

Icons that can be selected as a destination using the Interface Dial.

Icon searchable

Icons that can be searched using the d

Find

Nearest voice command.

Continued 61

62

 Map  Map Legend

■ Traffic icon

Traffic incident

Type

Icon display control

Yes

Icon selectable

No

Icon searchable

Yes

1 Traffic Incident

When you use the Interface Dial to position the cursor (round red circle) over the traffic incident icon, you can view the summary of the incident.

Press u

on the traffic incident icon to view a pop-up message describing the incident in detail.

 Map  Display Tracking

Display Tracking

H

SETTINGS button  Navi Settings  Map  Display Tracking

The navigation system can be set to display white tracking dots (“breadcrumbs”) on the map screen.

Rotate i

to select an option. Press u

.

The following options are available:

• On

: The system displays the white tracking dots.

2 Tracking Dots P. 97

• Off (factory default): Disables the feature.

Deleting Tracking Dots

H

SETTINGS button  Navi Settings  Map  Delete Tracking

Rotate i

to select Yes . Press u

.

1 Deleting Tracking Dots

When you transfer the vehicle to a third party, delete the tracking dots.

63

64

 Map  Correct Vehicle Position

Correct Vehicle Position

H

SETTINGS button  Navi Settings  Map  Correct Vehicle Position

Manually adjust the current position of the vehicle as displayed on the map screen if the position appears to be incorrect.

1.

Put the vehicle in Park.

2.

Rotate i

to select Correct

Vehicle Position . Press u

.

3.

Scroll the map to position the cursor over at your correct position.

Press u

.

1 Correct Vehicle Position

An apparent position error can occur where buildings, tunnels, and other objects block or reflect the GPS signals, forcing the system to use

“dead reckoning” to determine your location and direction.

Using this function to adjust vehicle position is not recommended. When the system reacquires a GPS signal, it will automatically place the vehicle in the correct location.

If you continually have to adjust the vehicle position, you may have problems with the GPS

reception or there may be database errors.

2 System Limitations P. 130

4.

Rotate i

to position the arrowhead in the correct direction the vehicle is facing.

5.

Press u

to select OK .

 Map  System Device Information

System Device Information

H

SETTINGS button  Navi Settings  Map  System Device Information

View database, software, device, and vehicle identification information.

1 System Device Information

You will need this information when ordering a map update.

2 Obtaining a Navigation Update Data

P. 133

Map Data Update

H SETTINGS button  Navi Settings  Map  Map Data Update

Check the map data update status when updating the map database.

1 Map Update Status

This operation is only available during a database update.

2 Obtaining a Navigation Update Data

P. 133

65

66

Navigation

This section describes how to enter a destination, select a route to take, and follow the route to your destination. It also describes how to change your route or destination along the way.

Entering a Destination ........................... 68

Address ................................................. 70

Address Book......................................... 76

Previous Destination............................... 77

Place Category ....................................... 78

Place Name ............................................ 80

Place Phone Number .............................. 83

ZAGAT................................................... 83

Download POI........................................ 86

Scenic Route .......................................... 87

Intersection ............................................ 88

Map Input.............................................. 89

Coordinate ............................................ 91

Calculating the Route ..............................92

Viewing the Routes .................................93

Driving to Your Destination ...................94

Viewing the Route ..................................94

Listening to Voice Guidance ....................98

Reaching a Waypoint ..............................99

Map Menu ..............................................100

Displaying the Map Menu .....................100

Directions .............................................102

Traffic Rerouting™................................104

Changing Your Route ............................106

Pausing the Route .................................107

Canceling the Route .............................107

Adding Waypoints ................................108

Editing the Destination List ................... 112

Taking a Detour ................................... 114

Avoiding Area ...................................... 114

Changing Your Destination ................. 115

Find Nearest Place ................................ 115

Selecting a Destination on the Map ...... 116

Entering a New Destination .................. 117

Resuming Your Trip .............................. 118

67

Entering a Destination

H

MENU button (on map)

This section describes how to enter a destination for route guidance.

Rotate i

to select an item. Press u

.

Select More Search Methods to display additional menu entries.

1 Entering a Destination d

“Display Destination” , d

“Display

Navigation”

If you press the MENU button when en route, the Route Option screen is displayed.

2 Changing Your Route P. 106

Prior to departure, you can set areas along your route to avoid.

2 Avoiding Area P. 114

68

The following items are available:

• Address

: Sets a destination by entering an address.

2 Address P. 70

• Address Book : Sets a destination by selecting an address stored in your Address

Book.

2 Address Book P. 76

• Previous Destination : Sets a destination by selecting a previous destination.

2 Previous Destination P. 77

 Entering a Destination 

• Go Home : Sets your home address as a destination.

2 Going Home P. 10

• Place Category : Sets a destination by selecting a place/landmark.

2 Place Category P. 78

• Place Name

: Sets a destination by entering a place name.

2 Place Name P. 80

• Place Phone No.

: Sets a destination by entering the phone number of a place/ landmark.

2 Place Phone Number P. 83

• ZAGAT : Sets a destination (restaurant) by using ZAGAT® SURVEY Rating

information.

2 ZAGAT P. 83

• Download POI : Sets a destination by using a list of the imported POI (category

and places) data you created.

2 Download POI P. 86

• Scenic Route : Sets a destination by using a list of scenic roads for each state (U.S.

and Canada only).

2 Scenic Route P. 87

• Intersection

: Sets a destination (intersection) by entering two streets.

2 Intersection P. 88

• Map Input : Sets a destination by scrolling through the map.

2 Map Input P. 89

• Coordinate

: Sets a destination by entering latitude and longitude.

2 Coordinate P. 91

1 Entering a Destination

ZAGAT provides restaurant information only in the U.S.

69

 Entering a Destination  Address

Address

H

MENU button  Address

Enter an address to use as the destination. The state or province you are currently in is displayed (e.g., California).

Rotate i

to select an item. Press u

.

70

The following items are available:

• City : Selects your destination city.

2 Selecting a City P. 72

• Street

: Selects your destination street.

2 Selecting a Street P. 73

• House Number : Enters the house number to select the street.

2 Selecting a Street by House Number P. 75

• ZIP Code : Enters the zip code to select the city.

2 Selecting a City by Zip Code P. 71

• Change State : Selects the state or province.

2 Selecting the State or Province P. 71

 Entering a Destination  Address

Selecting the State or Province

H

MENU button

 Address  Change State

Rotate i

to select a state from the list. Press u

.

1 Selecting the State or Province

Move w

or y

to select the following areas:

USA for the U.S. mainland, Alaska, Hawaii, and Puerto Rico

Canada

Mexico

Selecting a City by Zip Code

H

MENU button  Address  ZIP Code

1.

Enter the zip code of your destination.

2.

Move r

to select OK . Press u

.

1 Selecting a City by Zip Code

If your city is not listed, it may be part of a larger metropolitan area. Try entering the street first.

Continued 71

72

 Entering a Destination  Address

Selecting a City

H

MENU button  Address  City

3.

Rotate i

to select the destination city from the list. Press u

.

 Next, you are prompted to enter

a street name.

2 Selecting a Street P. 73

The name of the city where you are currently located is displayed.

1.

Enter the name of a different city, or move r

to select OK for the current city. Press u

.

1 Selecting a City

Vehicle position may not be displayed when:

• The automobile is traveling off-road.

The vehicle position data cannot be updated.

You do not need to enter spaces or symbols

(e.g., &, -, %). Partial matches are supported

(e.g., “ANGELES” to find “LOS ANGELES”).

Using Voice Command (English only)

Say d

“ City ” on the Find address by screen, and the following screen is displayed:

Say d

“Current City” to select your current

location, or say the name of a different city.

2 Selecting a Street P. 73

The Say city name screen is not displayed when your vehicle is in Puerto Rico or Mexico.

 Entering a Destination  Address

Non-detailed area mark: Try entering the street first and then select the city.

Selecting a Street

H

MENU button  Address  Street

2.

Rotate i

to select your destination city from the list. Press u

.

 A list of matching hits is automatically displayed after you enter several letters, with the closest match at the top of the list. Matching letters are highlighted.

Next, you are prompted to enter

a street name.

2 Selecting a Street P. 73

1 Selecting a City

If your city is not listed, it may be part of a larger metropolitan area. Try entering the street first.

1 Selecting a Street

When entering the names of major freeways, you can use the following abbreviations. For interstates, use an “I” (e.g., I-10). For U.S. freeways, use “US” (e.g., US-18). For state freeways, use the two-character state designation (e.g., CA-101). For county roads, use the appropriate designation (e.g., G-2).

Using Voice Command (English only)

Say d

“ Street ” on the Find address by screen, and the following screen is displayed:

1.

Enter the name of your destination street.

Do not enter the street type

(e.g., street, road, avenue) or direction (e.g., north, south, east, west).

 Move r

to select OK to display a list of streets. Press u

.

Say the name of your destination street, and say the street number as a string of individual numbers.

Set the route to your destination.

2 Calculating the Route P. 92

The Say street name screen is not displayed when your vehicle is in Puerto Rico or Mexico.

Continued 73

74

 Entering a Destination  Address

2.

Rotate i

to select your destination street from the list.

Press u

.

 A list of matching hits is automatically displayed after you enter several letters, with the closest match at the top of the list. Matching letters are highlighted.

3.

Enter the street number.

 Only valid street numbers can be entered.

4.

Move r

to select OK . Press u

.

5.

Set the route to your destination.

2 Calculating the Route P. 92

1 Selecting a Street

If you did not select a city first and there is more than one city with the specified street, a list of cities is displayed.

Rotate i

to select the desired city from the list.

Press u

.

Selecting a Street by House Number

H

MENU button

 Address  House Number

1.

Enter the house number.

Only a valid house number can be entered.

2.

Move r

to select OK . Press u

.

 If you did not yet select a street name, enter a street name when you are prompted.

3.

Rotate i

to select your destination street from the list.

Press u

.

 Select a city when you are prompted.

4.

Set the route to your destination.

2 Calculating the Route P. 92

 Entering a Destination  Address

75

76

 Entering a Destination  Address Book

Address Book

H

MENU button  Address Book

Select an address stored in your address book to use as the destination.

1.

Rotate i

to select your destination from the list. Press u

.

2.

Set the route to your destination.

2 Calculating the Route P. 92

 Move w

or y

to display only the entries in the categories you

have created.

2 Selecting an Address Book

Category P. 26

1 Address Book

If you have PIN-protected your address book, enter your PIN when prompted. Press u

to select OK . PINs are optional.

2 PIN Numbers P. 28

Move r

and rotate i

to select the following items:

Add New Address : Adds an entry to the

address book.

2 Adding an Address Book Entry P. 23

Sort : Selects Sort by Name or Sort by

Distance .

Delete All : Deletes all entries in the address book.

 Entering a Destination  Previous Destination

Previous Destination

H

MENU button  Previous Destination

Select an address from a list of your 50 most recent destinations to use as the destination. The list is displayed with the most recent destination at the top.

1.

Rotate i

to select a destination from the list. Press u

.

2.

Set the route to your destination.

2 Calculating the Route P. 92

1 Previous Destination

If Previous Destination is grayed out, there are no previous destinations entered.

Your home address and addresses stored in your address book are not added to the list of previous destinations.

Move r

and rotate i

to select Delete All to delete all previous destinations.

You can delete unwanted previous destinations

from the list.

2 Previous Destination P. 29

77

78

 Entering a Destination  Place Category

Place Category

H

MENU button  Place Category

Select the category of a place (e.g., Banking, Lodging, Restaurant) stored in the map database to search for the destination.

1.

Rotate

Press i u

.

to select a category.

2.

Rotate i

to select a subcategory.

Press u

.

2 List of Categories P. 148

1 Place Category

This option is convenient if you do not know the exact name of a place or if you want to narrow down the number of matches returned for places with a common name.

Move y

to select Category History to access your recently used place categories. Up to 30 categories can be stored.

You can also delete your recently used place categories.

2 Category History P. 30

Search POI Categories helps you to search the subcategory. When you enter a keyword and select OK , the list of appropriate subcategories is displayed.

 Entering a Destination  Place Category

3.

Rotate u

.

i

to select an item. Press

The following items are available:

• Search by Name : Searches for a place in the subcategory by name. Enter a city name when prompted.

• City Vicinity : Searches for a place in the subcategory within a 20-mile radius of a specific city. Enter a city name and then a place name when prompted. Only the first 1000 matching places/landmarks are displayed.

• Sort by Distance to Travel : Displays all the places in the subcategory sorted by distance from your current location. The closest place is displayed at the top.

4.

Rotate i

to select a place name from the list. Press u

.

5.

Set the route to your destination.

2 Calculating the Route P. 92

1 Place Category

The straight line distance (as the crow flies, not driving distance) and direction to the destination are shown for the highlighted place.

Restaurants with a z

icon have a ZAGAT® review. To display only restaurants with a

ZAGAT® review, move r

to select ZAGAT

Only , or say d

“Zagat” .

2 ZAGAT Review P. 85

ZAGAT provides restaurant information only in the U.S.

79

80

 Entering a Destination  Place Name

Place Name

H

MENU button  Place Name

Enter the name of a place (e.g., business, hotel, restaurant) stored in the map database to use as the destination.

1.

Enter a place name.

2.

Move r

to select OK to display a list of matching hits. Press u

.

1 Place Name

This option is convenient if you know the exact name of a place.

Once a name is entered and selected, move r

to select Sort by Name or Sort by Distance .

Matching letters are highlighted.

Restaurants with a z

icon have a ZAGAT® review.

2 ZAGAT P. 83

ZAGAT provides restaurant information only in the U.S.

3.

Rotate i

to select a place name from the list. Press u

.

 If the place name is in multiple categories, the categories are displayed when you select it.

2 Place Name in Multiple

Categories P. 81

4.

Set the route to your destination.

2 Calculating the Route P. 92

 Entering a Destination  Place Name

Place Name in Multiple Categories

If the place name is in multiple categories in the map database, the following screen is displayed.

1.

Rotate i

to select a place name.

Press u

.

1 Place Name in Multiple Categories

Matching letters are in highlighted.

2.

Rotate i

to select a subcategory.

Press u

.

Continued 81

82

 Entering a Destination  Place Name

3.

Rotate i

to select a place. Press u

.

4.

Set the route to your destination.

2 Calculating the Route P. 92

1 Place Name in Multiple Categories

Move r

to select Sort by City or Sort by

Distance .

 Entering a Destination  Place Phone Number

Place Phone Number

H

MENU button  More Search Methods  Place Phone Number

Select a destination by phone number. Only phone numbers in the database are recognized.

1.

Enter the area code and phone number.

2.

Rotate i

to select OK . Press u

.

3.

Set the route to your destination.

2 Calculating the Route P. 92

1 Place Phone Number

All 10 digits must be entered.

Phone numbers of private residences entered in your address book are not stored in the database and thus cannot be used to search for a destination.

A list is displayed if there are multiple locations in the database with the same phone number.

Rotate i

to select a place from the list. Press u

.

ZAGAT

H

MENU button  More Search Methods  ZAGAT

Find a restaurant by ZAGAT® SURVEY Rating information.

1.

Select a metropolitan area, region, neighborhood, and restaurant type when prompted.

1 ZAGAT®

Selecting this sorting method will show you

ZAGAT's highest-rated restaurants by the options, and not necessarily by distance from your current location.

Only states within the U.S. are displayed in the metropolitan area list.

Restaurant information for Mexico cannot be searched with ZAGAT.

Continued 83

84

 Entering a Destination  ZAGAT

2.

Rotate i

to select the sort method used to list the restaurants.

Press u

.

The following options are available:

• Food, Décor, Service : Lists the restaurants by the rating value.

• Cost : Lists the restaurants by the average cost of a meal (including drink and tip).

3.

Rotate i

to select a restaurant.

Press u

.

4.

Set the route to your destination.

2 Calculating the Route P. 92

 Entering a Destination  ZAGAT

ZAGAT Review

The ZAGAT® survey for some restaurants is included in the database and displayed when entering a restaurant as a destination. You can view an explanation of the data displayed for the surveyed restaurants.

1.

Rotate i

to select a restaurant with the z

icon from the place list. Press u

.

2.

Rotate i

to select ZAGAT

Review . Press u

.

1 ZAGAT Review

Scrolling through the review is disabled while the vehicle is moving.

ZAGAT provides restaurant information only in the U.S.

 Press u

(or say d

“Read List” ) to have the system read the ZAGAT® review.

 Move r

to select Help for details on the ratings and symbols.

85

86

 Entering a Destination  Download POI

Download POI

H

MENU button  More Search Methods  Download POI

Select a place imported into the navigation system as the destination.

1.

Rotate i

to select a category from the list. Press u

.

1 Download POI

Move r

and rotate i

to select the following items:

Import from USB : Imports POI data into the navigation system.

2 Importing POI Categories P. 31

Delete All : Deletes all POI entries.

Help with Feature : Views tips for the

Download POI feature.

2.

Rotate i

to select a place. Press u

.

3.

Set the route to your destination.

2 Calculating the Route P. 92

 Entering a Destination  Scenic Route

Scenic Route

H

MENU button  More Search Methods  Scenic Route

Select a scenic road as a destination (U.S. and Canada only).

1.

Rotate i

to select a state. Press u

.

1 Scenic Route

If you select a scenic road that runs through multiple states, only the portion of the road in the selected state is displayed.

2.

Rotate i

to select a scenic road.

Press u

.

3.

Set the route to your destination.

2 Calculating the Route P. 92

87

88

 Entering a Destination  Intersection

Intersection

H

MENU button  More Search Methods  Intersection

Select the intersection of two streets as the destination. The state or province for your current location is displayed at the top of the screen (e.g., California).

1.

Rotate i

to select the intersection search method. Press u

.

2.

Set the route to your destination.

2 Calculating the Route P. 92

The following options are available:

• City : Selects the city where the intersection is located. You are prompted to enter the name of the two intersecting streets.

2 Selecting a City P. 72

• Street : Selects the two intersecting streets. The city or cities that the streets are located in are displayed.

2 Selecting a Street P. 73

• Change State : Selects the state or province.

2 Selecting the State or Province P. 71

1 Intersection

It is usually easier to select Street to find the streets first. The city or cities that the streets are in will be displayed. If you select City and your city is not listed, it may be part of a larger metropolitan area. Try entering the street first.

If the intersection is outside the state you are currently in, rotate i

to select Change State .

2 Selecting the State or Province P. 71

If there is more than one intersection, you are prompted to select the intersection. If the two streets that you have selected do not intersect, no intersection is entered.

Map Input

H

MENU button  More Search Methods  Map Input

Use the Interface Dial to manually select an icon or a location on the map screen as the destination.

You are prompted to define the map area to display.

1.

Rotate i

to select an item. Press u

.

 Entering a Destination  Map Input

The following items are available:

• Current Position : Your current location is centered on the map.

• State : You are prompted to select the state.

2 Selecting the State or Province P. 71

• City : You are prompted to select the city.

2 Selecting a City P. 72

• USA, Canada and Mexico : Your current location is displayed on a map of the country.

Continued 89

90

 Entering a Destination  Map Input

2.

Scroll the map to position the cursor over your desired destination, adjusting the map scale as necessary.

If the address is not the desired location, scroll the map to another location and try again.

3.

Press u

to display the route calculation menu.

2 Calculating the Route P. 92

4.

Rotate i

to select Set as

Destination.

Press u

.

1 Map Input

Auto Zoom

Press u

repeatedly on the map to zoom in (to the scale 1/4 mile) while scrolling the map.

Information icons are displayed at scales from 1 mile to 1/4 mile. Place/landmark icons are displayed at 1/8 mile or less. Roads are displayed at 1/4 mile or less.

If you select multiple icons within the cursor radius, you are prompted to select one of the items from a list.

2 Selecting a Destination on the Map P. 116

 Entering a Destination  Coordinate

Coordinate

H

MENU button  More Search Methods  Coordinate

Specify a location using latitude and longitude map coordinates.

1.

Enter the latitude and select OK .

2.

Enter the longitude and select OK .

1 Coordinate

Latitude and longitude must be entered up to the seconds’ value.

3.

Move w

to scroll the map to position the cursor over your desired destination, adjusting the map scale as necessary.

If the address is not the desired location, scroll to another location and try again.

4.

Press u

to display the route

calculation menu.

2 Calculating the Route P. 92

5.

Rotate i

to select Set as

Destination.

Press u

.

91

92

Calculating the Route

This section describes how to calculate your route.

1.

Rotate i

to select Set as

Destination . Press u

.

 The system calculates and displays the route line on the map screen.

2 Route Line P. 96

Move w

to scroll the map around the destination.

The following options are available:

• View Routes : Displays three different routes.

2 Viewing the Routes P. 93

• Route Preference : Move r

to select Route Preference to change the route

preferences (calculating method).

2 Route Preference P. 35

2.

Follow the route guidance to your

destination.

2 Driving to Your Destination P. 94

 The system provides you with pop-up messages if your route passes through unverified areas, avoid areas, or areas with traffic restrictions.

1 Calculating the Route

The straight line distance (as the crow flies, not driving distance) and direction to the destination are shown.

You cannot use voice commands while the system is calculating the route.

Search Nearby

You can find the nearest place/landmark (e.g., nearest gas station) by specifying a category.

2 Find Nearest Place P. 115

Call

You can place a telephone call to the destination phone number. See your Owner’s Manual.

Save to Address Book

You can add the destination address to the address book.

2 Adding an Address Book Entry P. 23

Edit/Delete Entry

You can edit or delete the address book entry.

2 Editing an Address Book Entry P. 25

Edit Home Entry

You can edit your home address entry.

2 Home Address P. 27

ZAGAT Review

You can view the ZAGAT® rating information.

2 ZAGAT Review P. 85

 Calculating the Route  Viewing the Routes

Viewing the Routes

View three different routes to your destination.

Rotate i

to select a route. Press u

.

 The travel distance and estimated travel time is displayed for each route.

 The system calculates and displays the route line on the map screen.

2 Route Line P. 96

1 Viewing the Routes

It is not unusual for some calculated route options to be identical.

93

Driving to Your Destination

94

This section describes how to follow the route guidance to your destination, receive traffic and weather information and choose the icons displayed on the map screen.

Viewing the Route

Map Screen

After calculating the route to your destination, the route is displayed on

the map screen.

2 Map Screen Legend P. 8

As you drive, the system tracks your position on the map in real time and provides guidance as you approach

each guidance point on the route.

2 During Route Guidance P. 9

1 Viewing the Route d

“Display Map”

You can change the map scale using voice commands (e.g., say d

“Display 2 mile scale” ).

2 Map Scale Commands P. 142

You can also change the map scale by rotating i

.

You can control the icons displayed on the map screen using voice commands (e.g., say d

“Display post office”

).

2 Map Display Commands P. 142

You can obtain information about the route using voice commands (e.g., say d

“How long to the destination?”

).

2 Route Commands P. 144

You can display the next guidance point on the map screen by saying d

“Display Map Guide”

(when en route).

If you scroll the map while en route, the time and distance to destination indicators are replaced with an indicator showing distance from the current vehicle position.

You can display only the map screen or a split map-guidance screen.

2 Guidance Mode P. 43

 Driving to Your Destination  Viewing the Route

Guidance Screen

The guidance screen offers an alternative way to view your route.

The next guidance point is displayed as you approach each guidance point on the route.

You can also view a list of guidance directions.

1 Guidance Screen

A visual guide helps you check the guidance

screen.

2 Guidance Screen P. 9

Continued 95

96

 Driving to Your Destination  Viewing the Route

Route Line

When driving on verified streets, the route line is light blue. The route line display changes when driving on unverified streets:

Straight line guide

• If Unverified Routing is Off , the route line uses verified streets only

(when possible). If Straight Line

Guide is set to On , a pink “vector line” pointing directly towards your

destination is displayed.

2 Straight Line Guide P. 57

1 Route Line

You can set Unverified Routing to Off to follow your own route to the destination. If

Unverified Routing is On , be aware that unverified streets may not be displayed

accurately.

2 Unverified Routing P. 36

You can always view the entire route by simply saying d

“Display entire route.”

The route line may also consist of red, orange, or green segments when traffic information is

displayed.

2 Map Screen Legend

P. 8

2 Traffic Rerouting™ P. 104

Blue-pink route line

• If Unverified Routing is On , the route line changes to a blue-pink line to indicate that the route line uses unverified streets.

Deviating From the Planned Route

If you leave the calculated route, the system automatically recalculates a route to the desired destination based on your current location and direction.

2 Route Preference P. 35

 Driving to Your Destination  Viewing the Route

Tracking Dots

You can display a series of dots (breadcrumbs) to track the path you are taking. If

needed, you can follow the dots back to the mapped road you originally left.

2 Display Tracking P. 63

1 Tracking Dots

A message “Not on a digitized road” may appear when you drive half a mile away from a mapped road.

Breadcrumbs may occasionally be displayed in urban areas, such as large parking lots in shopping malls, in new subdivisions where the roads are not yet in the database, or in areas where a GPS signal is unavailable, such as in a parking garage.

Breadcrumbs are limited to approximately 150 miles. Breadcrumbs at the beginning of the trail are deleted if you exceed that distance.

Breadcrumbs are displayed only at 1/20, 1/8, 1/4, and 1/2 mile map scales.

97

98

 Driving to Your Destination  Listening to Voice Guidance

Listening to Voice Guidance

H

ENTER button (on map)  Voice

As you approach each guidance point, a pop-up window is displayed on the map screen with instructions for you to follow. Voice guidance for each guidance point is also provided.

Typically, you hear three prompts:

• 1/2 mile from the guidance point (2 miles on freeway)

• 1/4 mile from the guidance point (1 mile on freeway)

• Just before the guidance point

To replay voice guidance, rotate i

to select Voice in the Map Menu.

If you select Voice between guidance points, voice guidance for the next guidance point is provided.

1 Listening to Voice Guidance d

“Voice” (on the map screen)

You can turn voice guidance OFF if you prefer.

Press the SETTINGS button. Select System

Settings and set Volume to 0 .

When driving in unverified areas, the phrase “if possible” is inserted before each voice guidance prompt.

Voice in the Map Menu may be grayed out if:

The system is in process of gathering the route guidance information.

• The vehicle is out of the road (e.g., pulling in a parking lot).

The timing of voice guidance varies depending on the type of road you are on and the distance to the next guidance point.

Reaching a Waypoint

When you reach a waypoint, a pop-up message is displayed. You can continue or pause the route guidance.

Rotate i

to select No to pause the route guidance. Press u

.

 Select Yes to continue the guidance.

 Driving to Your Destination  Reaching a Waypoint

Resuming the route guidance

You can resume the route guidance in the following ways:

• Restart the engine when you stop your car (e.g., to rest, stop for gas, etc.).

2 Resuming Your Trip P. 118

• Select Resume Guidance from the navigation menu or the map menu.

2 Map Menu P. 100

2 Changing Your Route P. 106

99

Map Menu

Displaying the Map Menu

Use the Map Menu to control the icons displayed on the screen and to display traffic information, weather information, and messages. You can also use the Map Menu to find locations or to cancel the route.

1.

On the map screen, press u

.

 The Map Menu is displayed on the map screen.

1 Map Menu

If you scroll the map while en route, press the

NAV (or BACK) button to return to the current position map screen, then press u

.

Traffic Incidents

You must be in or near a traffic-enabled city to receive coverage for that area. FM Traffic is available in the lower 48 states, Canada and

Hawaii.

The incident icons are displayed on the 5 mile or less map scale.

2 Map Scale and Functions P. 60

2.

Rotate i

to select an item. Press u

.

100

The following items are available:

• Voice: Select to hear the voice guidance when en route.

2 Listening to Voice Guidance P. 98

 Map Menu  Displaying the Map Menu

• Map/Guidance : Allows you to select the map and guidance settings (display mode, icons to display on the map, map orientation, map color, and 3D view angle), display your current location and an overview of the map features.

2 Guidance Mode P. 43

2 Showing Icons on Map P. 51

2 Color P. 53

2 View (Map Orientation) P. 56

2 3D Angle Adjustment P. 57

2 Current Location P. 58

2 Map Legend P. 59

• Pause Guidance

: Pauses your current route.

2 Pausing the Route P. 107

• Resume Guidance : Resumes your current route. This item is displayed while the route guidance is paused.

• Cancel Route: Cancels your current route.

2 Canceling the Route P. 107

• Directions

: Displays a list of the guidance points.

2 Directions P. 102

• Search Nearby: Allows you to find the nearest place/landmark (e.g., nearest gas station) by specifying a category. You can then add the location to the list of

destinations, set as a waypoint, or set as your destination.

2 Find Nearest Place P. 115

• Traffic Incidents: Displays a list of the traffic incidents around your current location or on your current route.

2 Traffic Rerouting™ P. 104

1 Map Menu

Directions

The system provides freeway exit information only in the U.S.

101

102

 Map Menu  Directions

Directions

H

ENTER button (on map)  Directions

Display a list of the guidance points on your route for your confirmation.

1.

Rotate i

to select a guidance point from the list. Press u

.

 The system displays a map of the guidance point.

1 Directions

Guidance points with exit information are indicated by a (freeway exit information) icon. Move r

to select Exit Info to display the

exit information.

2 Freeway Exit Information P. 103

The system provides freeway exit information only in the U.S.

The route guidance information is automatically deleted when you reach your destination.

2.

Press u

to select Back to list or press the BACK button to return to the previous screen.

 Map Menu  Directions

Freeway Exit Information

H

ENTER button (on map)

 Directions  Exit Info

Display a list of the freeway exits for the route. You can view freeway exit information (whether the exit is near gas stations, restaurants, ATMs, etc.) and add new destinations or waypoints to the calculated route.

1.

Rotate i

to select an exit from the list. Press u

.

1 Freeway Exit Information d

“Display Freeway Exit Information”

You can scroll the map and select a (freeway exit information) icon on the map screen to display the freeway exit information. The icon is only displayed if there is exit information available.

Icons are displayed only at 1/4, 1/2, or 1 mile scale.

2 Showing Icons on Map P. 51

The system provides freeway exit information only in the U.S.

The route guidance information is automatically deleted when you reach your destination.

2.

Rotate i

to select a list item.

Press u

.

 Move w

or y

to display information for different exits.

 You can set the route to your destination.

2 Calculating the Route P. 92

103

 Map Menu  Traffic Rerouting™

Traffic Rerouting™

When driving to your destination, the system automatically searches for a faster

route based on traffic flow information and traffic incidents.

2 Map Screen Legend P. 8

2 Traffic Rerouting P. 38

1 Traffic Rerouting

Automatic traffic rerouting may not provide a detour route depending on circumstances.

104

Traffic Rerouting™ Manually

H

ENTER button (on map)

 Traffic Incidents

Manually avoid specific incidents and/or congestion on your route:

1.

Rotate i

to select an incident from the list. Press u

.

 The system displays the map screen and the incident location.

1 Traffic Rerouting™ Manually d

“Display traffic incidents” , d

“Display traffic list”

You can display traffic incidents and related information on the map screen using voice commands.

2 Map Display Commands P. 142

 Map Menu  Traffic Rerouting™

2.

Rotate u

.

i

to select Avoid . Press

Repeat step 1 to 2 as necessary.

3.

Move r

to select Reroute . Press u

.

 The system recalculates a detour route that avoids the traffic incidents.

1 Traffic Rerouting™ Manually

You can choose to avoid up to 10 traffic incidents. It is not always possible for the system to calculate a route that avoids all traffic incidents or specific traffic incidents you select.

The “On Route” tab on the Traffic List screen is only available during route guidance.

You cannot select an incident to avoid from the

“All” tab.

You can also detour around a traffic incident manually if you encounter an unexpected

obstacle.

2 Taking a Detour P. 114

105

Changing Your Route

H

MENU button (when en route)

This section describes how to alter your route, add an interim “waypoint” (pit stop), choose a different destination, cancel your current destination, and continue your trip after stopping.

Rotate i

to select an item. Press u

.

1 Changing Your Route d

“Display Destination” , d

“Display

Navigation” (when en route)

If you press the MENU button when not en

route, the Destination Menu screen is displayed.

2 Entering a Destination P. 68

106

The following items are available:

• Voice : Select to hear the voice guidance when en route.

2 Listening to Voice Guidance P. 98

• Destination List : Shows a list of waypoints. You can delete waypoints or edit the order of them.

2 Editing the Destination List P. 112

• Pause Guidance

: Pauses your current route.

2 Pausing the Route P. 107

• Resume Guidance : Resumes your current route. This item is displayed while the route guidance is paused.

• Cancel Route

: Cancels the route guidance.

2 Canceling the Route P. 107

• View Routes : Displays three different routes.

2 Viewing the Routes P. 93

 Changing Your Route  Pausing the Route

• Change Route Preference

: Changes the route preferences (calculating method).

2 Route Preference P. 35

• Detour

: Calculates a detour route.

2 Taking a Detour P. 114

• Avoid Streets : Avoids streets along your route.

2 Avoiding Area P. 114

Pausing the Route

H

MENU button (when en route)

Pause Guidance

Pause the route guidance and return to the map screen. The destination icons and all waypoint flags remain displayed on the map. Press the MENU button when en route and select Resume Guidance to resume the route guidance.

Canceling the Route

H

MENU button (when en route)

 Cancel Route

Cancel the route guidance and remove the destination and all waypoints from the destination list. The system then returns to the map screen.

1 Pausing the Route

You can also pause your route from the Map

Menu.

2 Map Menu P. 100

1 Canceling the Route

You can also cancel your route from the Map

Menu.

2 Map Menu P. 100

107

108

 Changing Your Route  Adding Waypoints

Adding Waypoints

Add up to four waypoints (pit stops) along the route to your destination.

Waypoints are displayed on the map screen as small, numbered red flags.

The route follows the waypoints in the order they are listed in the

Destination List.

1 Adding Waypoints

Waypoints allow you to stop for gas or food, for example, and then continue on to your destination.

Press the NAV button to return to the map screen without adding a waypoint at any time.

The search corridor used for adding waypoints can be adjusted.

2 Edit POI Search Radius Along Route P. 39

You can delete waypoints or edit the order of waypoints in the destination list.

2 Editing the Destination List P. 112

 Changing Your Route  Adding Waypoints

Adding Waypoints from the Route Menu

H

MENU button (when en route)

 Destination List  Add New destination 

Find Along Route

1.

Rotate i

to select a search method to add a waypoint. Press u

.

1 Adding Waypoints

Search method

“Search around” method

“Search along” method

The following items are available:

• Search Around: Searches in a spiral pattern around the location you select.

• Search Along : Searches within a “corridor” on either side of the locations you select.

2.

Rotate i

to select a waypoint category (e.g., GAS STATION ).

Press u

.

Continued 109

110

 Changing Your Route  Adding Waypoints

3.

Rotate i

to select a place. Press u

.

 The waypoint is added to the

Destination List.

4.

Rotate i

to select a location and move the order of destinations.

Press u

.

5.

Move r

and rotate i

to select

Start Route . Press u

.

 The route is automatically recalculated and displayed on the map screen.

 Changing Your Route  Adding Waypoints

Adding Waypoints from the Navigation Menu

H

MENU button (when en route)

 Destination List  Add New destination 

Use Nav Menu

1.

Rotate i

to select a method to

enter a waypoint.

2 Entering a Destination P. 68

 A new destination is added to the end of the Destination list.

1 Adding Waypoints from the Navigation Menu

You can edit the order of waypoints and destination.

2 Editing the Destination List P. 112

2.

Move r

and rotate i

to select

Start Route . Press u

.

 The route is automatically recalculated and displayed on the map screen.

111

112

 Changing Your Route  Editing the Destination List

Editing the Destination List

Editing the Order of Waypoints.

H

MENU button (when en route)  Destination List

1.

Move r

and rotate i

to select

Edit Order . Press u

.

1 Editing the Order of Waypoints

Move r

to rotate i

to select Show All on

Map to display the destination and waypoints on the map screen.

2.

Rotate i

to select a list item to move. Press u

.

3.

Rotate i

to select a new location.

Press u

.

4.

Move r

and rotate i

to select

Start Route . Press u

.

The route is automatically recalculated and displayed on the map screen.

 Changing Your Route  Editing the Destination List

Deleting Waypoints

H

MENU button (when en route)

 Destination List

1.

Rotate i

to select a list item to delete. Press u

.

1 Deleting Waypoints

Move r

and rotate i

to select Delete All to delete the destination and all the waypoints.

Select Show on Map to display the waypoint on the map screen.

2.

Rotate i

to select Delete . Press u

.

3.

Rotate i

to select Yes . Press u

.

113

114

 Changing Your Route  Taking a Detour

Taking a Detour

H

MENU button (when en route)  Detour

Calculate a detour route manually. The system attempts to calculate a new route by avoiding the next 5 miles (while on a freeway) or 1 mile (while on a surface street).

Avoiding Area

H

MENU button (when en route)

 Avoid Streets

Select a street or streets along your route to avoid.

1.

Rotate i

to select the street you want to avoid. Press u

.

 Repeat the procedure to avoid other streets.

1 Taking a Detour

The detour option is convenient if you encounter an unexpected obstacle such as a road closure or extremely heavy traffic congestion.

1 Avoiding Area

Avoiding certain streets is convenient if you know of road construction, road closures, or excessive traffic along the route.

You cannot choose specific streets you want to use, only those to avoid. However, you can select intersections or waypoints (places/landmarks) that the system will use in your route.

2 Adding Waypoints P. 108

You can store up to 10 streets to avoid. You cannot avoid your current street or the streets of your waypoint(s) or destination (system beeps if selected).

2.

Move r to select Recalculate

Route . Press u

.

 The system calculates a new route.

Changing Your Destination

There are several methods you can use to change the route destination.

Find Nearest Place

H

ENTER button (on map)  Search Nearby

Search for the nearest place/landmark on the map screen and set it as your destination.

1.

Rotate i

to select Search

Nearby . Press u

.

2.

Rotate i

to select a category type. Press u

.

3.

Rotate i

to select a place. Press u

.

4.

Rotate i

to select Set as

Destination . Press u

.

5.

Move r

to select Clear Current

Route . Press u

.

 The route is automatically recalculated and displayed on the map screen.

 Rotate i

to edit the order to set the location as a new waypoint. Press u

.

1 Find Nearest Place d

“Find Nearest…” (on map screen)

The Find Nearest voice command is the fastest method of specifying a place/landmark as your

destination. Many kinds of places can be found.

2 Find Place Commands P. 143

115

116

 Changing Your Destination  Selecting a Destination on the Map

Selecting a Destination on the Map

Select a new destination when en route by selecting a location on the map.

1.

Scroll the map to position the cursor over your desired destination, adjusting the map scale as necessary. Press u

.

 If the address displayed is not the desired location, press the

BACK button and repeat the procedure.

2.

Rotate i

to select Set as

Destination . Press u

.

2 Calculating the Route P. 92

1 Selecting a Destination on the Map

If there is more than one icon or street under the map cursor, you are prompted to select the item from a list.

Rotate i

to select an item. Press u

.

3.

Move r

to select Clear Current

Route . Press u

.

 The route is automatically recalculated and displayed on the map screen.

 Rotate i

to edit the order to set the location as a new waypoint. Press u

.

 Changing Your Destination  Entering a New Destination

Entering a New Destination

H

MENU button (when en route)  Destination

Enter a new destination using the Destination Menu screen even when you are en route.

1.

Rotate i

to select a method to

enter a new destination.

2 Entering a Destination P. 68

 After entering a new destination, the address is displayed on the Calculate

Route screen.

2.

Rotate i

to select Set as

Destination . Press u

.

3.

Move r

to select Clear Current

Route . Press u

.

 The route is automatically recalculated and displayed on the map screen.

 Rotate i

to edit the order to set the location as a new waypoint. Press u

.

1 Entering a New Destination d

“Display Destination” , d

“Display

Navigation”

117

118

Resuming Your Trip

Stop your vehicle en route (e.g., to rest, stop for gas, etc.), and then continue on your route.

If you did not complete your route, the Continue Trip screen is displayed when you restart your vehicle.

Rotate i

to select Set as

Destination . Press u

.

 You can continue on the same route.

Move w

to scroll the map around the destination.

 Press the BACK button to cancel your destination.

• Route Preference : Move r

to select Route Preference to change the route

preferences (calculating method).

2 Route Preference P. 35

• View Routes

: Displays three different routes.

2 Viewing the Routes P. 93

1 Resuming Your Trip

The Continue Trip screen has the same options as when you calculate a route.

2 Calculating the Route P. 92

You can also cancel your destination by pressing any hard button except the a

button

Search Nearby

You can find the nearest place/landmark (e.g., nearest gas station) by specifying a category.

2 Find Nearest Place P. 115

Call

You can place a telephone call to the destination phone number. See your Owner’s Manual.

Save to Address Book

You can add the destination address to the address book.

2 Adding an Address Book Entry P. 23

Edit/Delete Entry

You can edit or delete the address book entry.

2 Editing an Address Book Entry P. 25

Edit Home Entry

You can edit your home address entry.

2 Home Address P. 27

ZAGAT Review

You can view the ZAGAT® rating information.

2 ZAGAT Review P. 85

Troubleshooting

Troubleshooting ................................... 120

Map, Voice, Entering Destinations ........ 120

Traffic .................................................. 122

Guidance, Routing ............................... 123

Update, Coverage, Map Errors ............. 125

Display, Accessories.............................. 125

Miscellaneous Questions ...................... 125

Error Messages ...................................... 126

Navigation System................................ 126

119

120

Troubleshooting

Map, Voice, Entering Destinations

The Startup Confirmation screen is displayed every time I start the car.

Problem

The navigation system reboots by itself (returns to the opening screen).

How do I specify a destination when an entered city or street could not be found?

Why do some letters become grayed out when I enter an address?

How do I delete Personal Addresses, Previous

Destinations, or the Home Address?

I cannot hear the navigation system voice.

The voice control system is having difficulty recognizing my voice commands.

I cannot give voice commands.

Solution

This is normal. The Startup Confirmation screen reminds you and your guest drivers to always operate the navigation system in a safe manner. The Startup Confirmation screen goes off after a certain period of time and the top screen of the last mode is displayed.

A reboot can be caused by extreme temperatures or shock from bumpy roads, and does not necessarily indicate a problem. If this happens frequently, please see a dealer.

• Try entering the street first. Some cities are lumped in with a major metro area. In rural “unverified” areas or new subdivisions, streets may be missing or only partially numbered.

• Try selecting the destination directly from the map.

2 Map Input P. 89

As you enter each letter in an address or a place/landmark, the navigation system looks in the database to see what letters are possible and grays out letters that do not apply.

1.

Press the SETTINGS button. Select Navi Settings > Personal Info to display the types of information.

2.

Select the type of address to delete.

3.

Select Delete .

1.

Press the SETTINGS button. Select System Settings and check that Volume is not set to 0 .

2.

Select Voice Rec.

and set Voice Prompt to On .

• Check that the vents are not blowing air onto the microphone on the ceiling, the vehicle is as quiet as possible, and you are using the correct command when speaking.

2 Voice Recognition P. 21

• Say d

“Voice Help” on any screen to see a list of the applicable voice commands.

Make sure you selected OK at the Startup Confirmation screen.

2 Start-up P. 18

 Troubleshooting  Map, Voice, Entering Destinations

Problem

I cannot select an option using the Interface Dial.

Solution

To reduce potential driver distraction, certain onscreen functions and features are limited or inoperable while the vehicle is moving. Use voice commands or pull over to proceed.

The navigation system pronunciation of street names in the guidance command or destination address sounds strange.

The screen is bright when I drive at night.

The basic guidance phrases use a studio-recorded voice, but street names are pronounced using a machine-generated voice. Consequently, the name may be mispronounced or sound strange at times.

1.

Check that the nighttime dashboard brightness control is not set to maximum.

2.

Press the SETTINGS button. Select Navi Settings > Map > Color (Night) . Set the

Night color to Black for the best contrast.

2 Switching Display Mode Manually P. 54

The screen is dark when I drive during the day.

How do I change or remove my PIN?

Press the SETTINGS button. Select Navi Settings > Map > Color (Day) . Set the Day

color to White for the best contrast.

2 Switching Display Mode Manually P. 54

1.

Press the SETTINGS button. Select Navi Settings > Personal Info > PIN Number >

Address Book PIN or Go Home PIN .

2.

Enter your existing PIN. You then have the choice to change or remove the PIN.

2 PIN Numbers P. 28

A dealer must reset the PIN for you.

I have forgotten my PIN. How do I reset the PIN for

Home or the PIN for personal addresses?

Why is Call grayed out on the Calculate Route screen? Your phone is not paired to Bluetooth ® HandsFreeLink® or, if paired, your phone is in use. See your Owner’s Manual.

121

122

 Troubleshooting  Traffic

Traffic

Problem

My FM Traffic is missing or is not displaying properly.

What is wrong?

The navigation system sometimes provides a detour route when I am driving a route on the freeway.

The navigation system routes me to an exit and an alternate freeway with unknown flow speeds or surface streets.

How can I ignore the detour route and return to the original route?

Solution

Verify the following:

• FM Traffic relies on a clear FM signal. If signal strength is low, traffic data may not be available.

• Check the traffic icons and traffic flow on the Navi Settings.

2 Showing Icons on Map P. 51

• It is possible that there is a temporary technical problem with your metropolitan area traffic.

You can call Honda Automobile Customer Service to see if there is an outrage.

2 Honda Automobile Customer Service Contact Information P. 132

• If the situation persists, see your Honda dealer for assistance.

If Traffic Rerouting is set to On , the navigation system provides a detour route to

your destination only if it can find a significantly faster route than the original one.

2 Traffic Rerouting P. 38

The navigation system predicts which route should be faster based on freeway congestion along your route. Use your own experience to determine whether the alternate route would be faster.

Press the SETTINGS button. Select Navi Settings > Routing , and set Traffic

Rerouting to Off .

2 Traffic Rerouting P. 38

 Troubleshooting  Guidance, Routing

Guidance, Routing

Problem Solution

The navigation system does not route me the same way I would go or the same way as other mapping systems.

The navigation system attempts to generate the optimal route. You can change the

route preferences used when calculating a route.

2 Route Preference P. 35

The navigation system wants to route me around potential traffic problems. How do I stop these pop-up messages?

The street I’m on is not shown on the map screen.

The vehicle position icon is not following the road and the “GPS icon” text in the upper left hand corner of the screen is white or missing.

Press the SETTINGS button. Select Navi Settings > Routing , and set Traffic

Rerouting to Off

.

2 Traffic Rerouting P. 38

The mapping database is constantly undergoing revision. You can access the most recent information on the internet.

2 Map Coverage P. 133

• Check that the GPS antenna (located in the dashboard) is not blocked. For best reception, remove items from the dashboard, such as radar detectors, cell phones, or loose articles.

• Metallic tinting or other aftermarket devices can interfere with the GPS reception.

Please consult a dealer.

2 GPS System P. 130

Your route has entered an unverified area.

2 Unverified Routing P. 36

The blue highlighted route and voice guidance stopped or turned into a blue/pink line before I got to my destination.

How do I stop the map from rotating as I drive along?

Press the SETTINGS button. Select Navi Settings > Map > View > North-Up , or say d

“Display north-up” to change the map orientation.

The “time to destination” display sometimes increases even though I am getting closer to my destination.

If your speed reduces due to slower traffic, the navigation system updates the “time to destination” based on your actual road speed to give you a better estimate of arrival time.

The vehicle position icon on the map “lags” a short distance behind, especially when I arrive at an intersection.

This is normal. The navigation system is unaware of the width of intersections. Large

differences in vehicle position can indicate a temporary loss of the GPS signal.

2 GPS System P. 130

Continued 123

124

 Troubleshooting  Guidance, Routing from my screen?

routing.

Problem

The screen is showing white dots as I drive along.

How do I remove the white dots (“breadcrumbs”)

A road that I selected to avoid is being used when

My elevation (shown when I display the current position) seems to fluctuate even though my elevation has not changed.

My elevation is missing on the “current position” screen.

Solution

These dots are called “breadcrumbs.” These are displayed if Display Tracking is set to

On .

2 Display Tracking P. 63

Press the SETTINGS button. Select Navi Settings > Map , set Display Tracking to Off or select Delete Tracking

to remove the white dots from the map.

2 Display Tracking P. 63

When you “draw” your area to avoid, make sure to select sections of roads that

include at least one intersection.

2 Avoiding Area P. 114

This is normal. The elevation can vary ±100 feet due to GPS calculation errors.

2 GPS System P. 130

The elevation is only displayed if the GPS antenna can receive signals from at least four satellites. Try moving the vehicle into an open area. The elevation is also not displayed if the calculated elevation is zero or below sea level.

 Troubleshooting  Update, Coverage, Map Errors

Update, Coverage, Map Errors

Problem

My city is not part of a fully verified detailed coverage area.

Does the navigation system work outside North

America?

How do I report errors I find in the database?

Solution

The mapping database is constantly undergoing revision. You can access the most recent information on the internet.

2 Map Coverage P. 133

The navigation system contains maps for the 50 U.S. states, Canada, Puerto Rico, and

Mexico. The navigation system will not work in other countries.

2 Map Coverage P. 133

Minor errors are bound to occur in a large database. If you encounter major errors, see

2 Reporting Errors P. 132

Display, Accessories

Problem

The display appears dim when starting the car in really cold weather.

Solution

This is normal. The display will become brighter after a few minutes.

Miscellaneous Questions

Problem

My battery was disconnected or went dead, and the navigation system is asking for a code.

Solution

Press and hold the PWR

9

(Power) button for two seconds. The system should reactivate. If you have installed an aftermarket system, contact a dealer.

125

126

Error Messages

Navigation System

Error Message

The display temperature is too high. For protection, the system will shut off until the display cools down.

System temp is low. System will shut down until it warms up.

The navigation system temperature is too low. For protection, the system will shut off until it warms up.

Solution

This message appears briefly when the display temperature is too high. The navigation system turns off until the display cools down. The system turns back on automatically when the display cools down.

The navigation system has difficulty reading the HDD when the temperature is below approximately -22°F. The navigation system starts up automatically when the display warms up.

The navigation system atmospheric pressure is too low. For protection, the system will shut off until the pressure returns to safe levels.

The HDD is inoperable due to low atmospheric pressure. Move your vehicle to the place where the atmospheric pressure is high.

The navigation system temperature is too high. For protection, the system will shut off until it cools down.

The navigation system has difficulty reading the HDD when the temperature is high.

The navigation system starts up automatically when the system cools down.

System temp is too high. System will shut down until it cools down.

HDD access error. Please consult your dealer.

HDD access error. The system will reset and attempt to correct the problem.

Writing of the data to the HDD failed with a cause other than low temperature, high temperature, and low atmospheric pressure. After a short wait, try to operate the system again. If this does not solve the problem, consult with the dealer.

Reference Information

System Initialization ..............................128

Entering the Security Code....................128

Acquiring GPS Information....................128

Startup Confirmation Screen .................129

Map Matching ......................................129

System Limitations ................................130

GPS System...........................................130

Address Calculation ..............................130

Database ..............................................130

Customer Assistance .............................132

Resolving Problems ...............................132

Reporting Errors ....................................132

Honda Automobile Customer Service

Contact Information............................132

Visiting a Dealer ................................... 132

Map Coverage ..................................... 133

Obtaining a Navigation Update Data .... 133

Traffic Information ............................... 134

Operation in Alaska, Hawaii, Canada,

Puerto Rico, and Mexico ..................... 134

Legal Information ................................. 135

Copyrights ........................................... 135

User Agreements ................................. 135

As required by the FCC ........................ 139

127

128

System Initialization

The navigation system must be initialized if power to the navigation system is interrupted for any reason (e.g., the battery was disconnected).

Entering the Security Code

Find the navigation system’s security code and serial number label in your Owner’s

Manual kit. Do not store the label in your vehicle. If you lose the label, you must first retrieve the serial number, and then obtain the code. You can find out about your serial number and security code from a dealer.

1.

Set the power mode to ON, and turn on the audio system.

 If you set the power mode to

ACCESSORY, you will be requested to enter the security code. See step 3.

2.

Press and hold the PWR

9

(Power) button for more than two seconds.

The system is reactivated when the system’s control unit recognizes that the system is in your vehicle.

If the control unit fails to recognize,

“ENTER CODE” appears on the navigation screen.

3.

If necessary, enter the security code.

 If you do not enter the security code correctly after 10 tries, leave the system for one hour before trying again, or visit a dealer to have the system reset.

NOTE:

In the U.S. you can register the security code at Owner Link (owners.honda.com.), and find information on how to retrieve the serial number and obtain the code at radio-navicode.honda.com

.

Acquiring GPS Information

Depending on the length of time the power was interrupted, your system may require GPS initialization.

If initialization is not necessary, the system proceeds directly to the Startup

Confirmation screen.

If the system fails to locate a sufficient number of satellites to locate your position within 10 minutes, the following screen is displayed.

 System Initialization  Startup Confirmation Screen

If you are experiencing GPS reception

problems:

2 GPS System P. 130

Startup Confirmation

Screen

The Startup Confirmation screen is displayed when initialization has successfully completed. It is displayed every time you start your vehicle. Press u

to select OK to continue.

Map Matching

Map matching is the process of using the acquired GPS information to locate your position on the map screen. If you are on a mapped road, the name of the road is displayed along the bottom of the map screen when map matching is completed.

Do not enter a destination until the road name is displayed.

The system may initially show your location on a different street (e.g., in urban areas where streets are close together), may show an incorrect elevation, or may delay the display of the vehicle position icon at intersections. This is normal; the system will correct itself while you drive.

129

System Limitations

130

GPS System

The signals received from the GPS satellites are extremely weak (less than a millionth of the strength of a local FM station) and require an unobstructed view of the sky.

The GPS antenna is located in the dashboard. The signal reception can easily be interrupted or interfered with by the following:

• Metallic window tint on the front or side windows

• Cell phones, PDAs, or other electronic devices docked in a cradle or lying loose on the dashboard

• Remote starters or “hidden” vehicle tracking systems mounted near the navigation unit

• Audio electronic devices mounted near the navigation unit

• Trees, tall buildings, freeway overpasses, tunnels, or overhead electrical power wires

The GPS is operated by the U.S.

Department of Defense. For security reasons, there are certain inaccuracies built into the GPS for which the navigation system must constantly compensate. This can cause occasional positioning errors of up to several hundred feet.

Address Calculation

The destination icon shows only the approximate location of a destination address. This occurs if the number of possible addresses is different from the number of actual addresses on a block. For example, the address 1425 on a 1400 block with 100 possible addresses

(because it is followed by the 1500 block) will be shown a quarter of the way down the block by the system. If there are only

25 actual addresses on the block, the actual location of address 1425 would be at the end of the block.

Database

The digitized map database reflects conditions as they existed at various points in time before production. Accordingly, your database may contain inaccurate or incomplete data or information due to the passage of time, road construction, changing conditions, or other causes.

For example, some places/landmarks may be missing when you search the database because the name was misspelled, the place was improperly categorized, or a place/landmark is not yet in the database.

This is also true for police stations, hospitals, and other public institutions. Do not rely on the navigation system if you need law enforcement or hospital services.

Always check with local information sources.

In addition, the map database contains verified and unverified areas. Unverified streets may be missing from the map, in the wrong location, or have an incorrect name or address range. A message will warn you if your route includes unverified streets. Exercise additional caution when driving in unverified areas.

The database does not include, analyze, process, consider, or reflect any of the following categories of information:

• Neighborhood quality or safety

• Population density

• Availability or proximity of law enforcement

• Emergency, rescue, medical, or other assistance

• Construction work, zones, or hazards

• Road and lane closures

• Legal restrictions (such as vehicular type, weight, load, height, and speed restrictions)

• Road slope or grade

• Bridge height, width, weight, or other limits

• Traffic facilities safety

• Special events

• Pavement characteristics or conditions

Every effort has been made to verify that the database is accurate. The number of inaccuracies you experience increases the longer you go without obtaining an

updated map database.

2 Obtaining a Navigation Update Data

P. 133

We assume no liability for any incident that may result from an error in the program, or from changed conditions not noted above.

 System Limitations  Database

131

132

Customer Assistance

Resolving Problems

If you run into a specific issue that you cannot resolve, consult the following help resources:

• For navigation system issues:

2 Troubleshooting P. 120

There are also FAQs available online at automobiles.honda.com.

For traffic-related issues:

2 Traffic P. 122

• For reporting issues with the database or places/landmarks:

2 Reporting Errors P. 132

• Call Honda Automobile Customer

Service.

2 Honda Automobile Customer Service

Contact Information P. 132

Reporting Errors

You can help to improve database accuracy by reporting any errors you encounter.

• Report errors in freeways and main

“verified” roads shown in black on the map at http://mapreporter.navteq.com/ dur-web-external/ .

• Please do not report errors in purple

“unverified” roads. Maps for these

areas are provided for reference only.

2 Unverified Routing P. 36

• Please do not report errors in places/ landmarks, such as changes in business names. Information about points of interest are constantly being updated.

An updated database is available for purchase, usually in the fall of each year.

2 Obtaining a Navigation Update Data

P. 133

• For vehicle position icon errors, screen error messages, or other GPS-related

errors:

2 Troubleshooting P. 120

2 System Limitations P. 130

Honda Automobile

Customer Service Contact

Information

Honda Navi

American Honda Motor Co., Inc.

Honda Automobile Customer Service

Mail Stop 500-2N-7E

1919 Torrance Blvd.

Torrance, CA 90501-2746

Tel: (800) 999-1009

Fax: (310) 783-3273

Visiting a Dealer

If you have a question that you cannot resolve using the available help resources, you can consult a dealer. Please identify the specific issue (e.g., error occurs when you enter a specific address, when driving on a certain road, or just when it’s cold) so that the service technician can refer the issue to the factory so that a solution can be found. Be patient, the service technician may be unfamiliar with your specific issue.

 Customer Assistance  Map Coverage

Map Coverage

The navigation system provides map coverage for the United States, Canada,

Puerto Rico, and Mexico. The map coverage consists of accurately mapped

(verified) metropolitan areas and a less accurate (unverified) rural database. Note that unverified areas are constantly being reviewed and converted to verified areas each year.

Map coverage update information is available from Honda Automobile

Customer Service or online at www.hondanavi.com

.

To find navigation system update information:

1.

Visit www.hondanavi.com

.

2.

Enter your vehicle model and model year.

3.

Click Map Coverage to display a list of verified coverage areas on the most recent update.

4.

Click Map Coverage Details to display a

PDF document with a full listing of all coverage areas.

Adobe® Reader® is required for viewing and printing the Portable

Document Format (PDF) documents.

To download the latest version of

Adobe Reader, visit http:// get.adobe.com/reader/ .

Obtaining a Navigation

Update Data

Honda is continually expanding the scope of the navigation system. Navigation system software upgrades may be made available periodically, usually in the fall of each year.

To purchase an updated data file:

1.

Obtain your vehicle’s VIN number and

the System/Device Information.

2 System Device Information P. 65

2.

Call the Honda Navigation Disc

Fulfillment Center at (888) 291-4675, or order online at www.hondanavi.com.

Update data is not available from a dealer.

However, the dealer may assist you in obtaining an update data for you out of courtesy. There is no program for free updates.

133

134

 Customer Assistance  Traffic Information

Traffic Information

• Continuously updated traffic information is available in major metropolitan areas across the 48 contiguous states and Canada. A list of coverage areas is available online.

• Visit automobiles.honda.com/traffic for a complete listing of coverage areas and other information.

Operation in Alaska,

Hawaii, Canada, Puerto

Rico, and Mexico

Map Coverage

All roads displayed on the map screens are verified roads. Information in this manual relating to “unverified” roads or areas is not applicable.

Address and Place Entry

Screens

Entering a destination address or place/ landmark on another island may result in a screen caution message. This is because there are no ferry routes between islands in the database.

Puerto Rico and Mexico

If Street Name Guidance is set to On , the street names will not be read out by voice guidance. This may change in a future data update.

Legal Information

Copyrights

• Infogroup-Data: Certain business data provided by Infogroup © 2011, All

RIghts Reserved.

• EXIT-Data: © ZENRIN CO., LTD. 2011.

All rights reserved.

• Building foot print: © ZENRIN CO., LTD.

2011. All rights reserved.

• Junction View Data: © ZENRIN USA,

INC. 2011. All rights reserved.

• ZAGAT SURVEY: © 2012 Zagat Survey,

LLC. Zagat Survey is a registered trademark of Zagat Survey, LLC The

Zagat Content displayed may not reflect the most up-to-date Zagat Content available to the public.

• Brand icon: The marks of companies displayed by this product to indicate business locations are the marks of their respective owners. The use of such marks in this product does not imply any sponsorship, approval, or endorsement by such companies of this product.

User Agreements

Navigation System User

Agreement

In using this HDD “Satellite Linked

Navigation System” (the “HDD”), which includes HONDA MOTOR CO., LTD. software, ALPINE ELECTRONICS, INC. software, and NAVTEQ database contents

(hereinafter referred to as “Licensors”), you are bound by the terms and conditions set forth below. By using your copy of the

HDD, you have expressed your Agreement to the terms and conditions of this

Agreement. You should, therefore, make sure that you read and understand the following provisions. If for any reason you do not wish to be bound by the terms of this Agreement, please return the HDD to your dealer.

• The HDD may not be copied, duplicated, or otherwise modified, in whole or in part, without the express written permission of the Licensors.

• The HDD may not be transferred or sublicensed to any third party for profit, rent or loan, or licensed for reuse in any manner.

• The HDD may not be decompiled, reverse engineered or otherwise disassembled, in whole or in part.

• The HDD may not be used in a network or by any other manner of simultaneous use in multiple systems.

• The HDD is intended solely for personal use (or internal use where the end-user is a business) by the consumer. The HDD is not to be used for commercial purposes.

• The Licensors do not guarantee to the client that the functions included in the

HDD meet the specific objectives of the user.

• Licensor shall not be responsible for any damages caused by the use of the HDD to the actual user or to any third party.

• The warranty on the HDD shall not extend to an exchange or refund due to misspelling, omission of letters, or any other cosmetic discrepancy in the contents of the HDD.

• The right to use the HDD shall expire either when the user destroys the HDD or software, or when any of the terms of this Agreement are violated and the

Licensors exercise the option to revoke the license to use the HDD or software.

Continued 135

 Legal Information  User Agreements

136

• The terms and conditions hereof apply to all subsequent users and owners as well as to the original purchaser.

• The logos of oil companies, hotels, convenience stores, and other businesses are displayed for your information and convenience, and in no way imply any sponsorship, approval or endorsement of these companies, or their products. The logos are trademarks of their respective owners.

• The marks of companies displayed by this product to indicate business locations are the marks of their respective owners.

• The use of such marks in this product does not imply any sponsorship, approval, or endorsement by such companies of this product.

The user shall indemnify and save harmless the Licensors, and their officers, employees and agents, from and against any claim, demand or action, irrespective of the nature of the cause of the claim, demand or action, alleging loss, costs, expense, damages or injuries (including injuries resulting in death) arising out of the use or possession of the HDD or software.

Use, duplication, or disclosure of this HDD by or on behalf of the United States government is subject to “Restricted

Rights” as set forth at FAR 52.227-14, -19 or DFARS 252.227-7013, as applicable.

Manufacturers are the Licensors, including

HONDA MOTOR CO., LTD., 2-1-1 Minami

Aoyama Minato-Ku Tokyo 107-8556

JAPAN., Alpine Electronics, Inc., 20-1

Yoshima Kogyodanchi, Iwaki, Fukushima

970-1192 JAPAN., NAVTEQ Corporation,

425 W Randolph St. Chicago, IL 60606,

USA.

Navigation System END USER

LICENSE AGREEMENT

You have acquired a device (“DEVICE”) that includes software licensed by Alpine

Electronics, Inc. (collectively “ALPINE”) from an affiliate of Microsoft Corporation

(collectively “MS”). Those installed software products of MS origin, as well as associated media, printed materials, and

“online” or electronic documentation

(“SOFTWARE”) are protected by international intellectual property laws and treaties. The SOFTWARE is licensed, not sold. All rights reserved.

IF YOU DO NOT AGREE TO THIS END USER

LICENSE AGREEMENT (“EULA”), DO NOT

USE THE DEVICE OR COPY THE SOFTWARE

INSTEAD, PROMPTLY CONTACT ALPINE

FOR INSTRUCTIONS ON RETURN OF THE

UNUSED DEVICE(S) FOR A REFUND. ANY

USE OF THE SOFTWARE, INCLUDING BUT

NOT LIMITED TO USE ON THE DEVICE,

WILL CONSTITUTE YOUR AGREEMENT TO

THIS EULA (OR RATIFICATION OF ANY

PREVIOUS CONSENT).

• GRANT OF SOFTWARE LICENSE

This EULA grants you the following license: You may use the SOFTWARE only on the DEVICE.

• NOT FAULT TOLERANT

THE SOFTWARE IS NOT FAULT

TOLERANT. ALPINE HAS

INDEPENDENTLY DETERMINED HOW TO

USE THE SOFTWARE IN THE DEVICE,

AND MS HAS RELIED UPON ALPINE TO

CONDUCT SUFFICIENT TESTING TO

DETERMINE THAT THE SOFTWARE IS

SUITABLE FOR SUCH USE.

• NO WARRANTIES FOR THE SOFTWARE

THE SOFTWARE is provided “AS IS” and with all faults. THE ENTIRE RISK AS TO

SATISFACTORY QUALITY,

PERFORMANCE, ACCURACY, AND

 Legal Information  User Agreements

EFFORT (INCLUDING LACK OF

NEGLIGENCE) IS WITH YOU. ALSO,

THERE IS NO WARRANTY AGAINST

INTERFERENCE WITH YOUR

ENJOYMENT OF THE SOFTWARE OR

AGAINST INFRINGEMENT. IF YOU HAVE

RECEIVED ANY WARRANTIES

REGARDING THE DEVICE OR

SOFTWARE THOSE WARRANTIES DO

NOT ORIGINATE FROM, AND ARE NOT

BINDING ON, MS.

NO LIABILITY FOR CERTAIN DAMAGES.

EXCEPT AS PROHIBITED BY LAW, MS,

MICROSOFT CORPORATION AND THEIR

AFFILIATES SHALL HAVE NO LIABILITY

FOR ANY INDIRECT, SPECIAL,

CONSEQUENTIAL OR INCIDENTAL

DAMAGES ARISING FROM OR IN

CONNECTION WITH THE USE OR

PERFORMANCE OF THE SOFTWARE.

THIS LIMITATION SHALL APPLY EVEN IF

ANY REMEDY FAILS OF ITS ESSENTIAL

PURPOSE. IN NO EVENT SHALL MS,

MICROSOFT CORPORATION AND/OR

THEIR AFFILIATES BE LIABLE FOR ANY

AMOUNT IN EXCESS OF U.S. TWO

HUNDRED FIFTY DOLLARS

(U.S.$250.00).

• SPEECH RECOGNITION

If the SOFTWARE includes speech recognition component(s), you should understand that speech recognition is an inherently statistical process and that recognition errors are inherent in the process. Neither ALPINE nor its suppliers shall be liable for any damages arising out of errors in the speech recognition process.

• LIMITATIONS ON REVERSE

ENGINEERING, DECOMPILATION, AND

DISASSEMBLY

You may not reverse engineer, decompile, or disassemble the

SOFTWARE, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation.

• ADDITIONAL SOFTWARE/SERVICES

The SOFTWARE may permit ALPINE, MS,

Microsoft Corporation or their affiliates to provide or make available to you

SOFTWARE updates, supplements, addon components, or Internet-base service components of the SOFTWARE after the date you obtain your initial copy of the

SOFTWARE (“Supplemental

Components”).

 If ALPINE provides or makes available to you Supplemental Components and no other EULA terms are provided along with the

Supplemental Components, then the terms of this EULA shall apply.

If MS, Microsoft Corporation or their affiliates make available

Supplemental Components, and no other EULA terms are provided, then the terms of this EULA shall apply, except that MS, Microsoft

Corporation or affiliate entity providing the Supplemental

Component(s) shall be licensor of the

Supplemental Component(s).

 ALPINE, MS, Microsoft Corporation and their affiliates reserve the right to discontinue any Internet-based services provided to you or made available to you through the use of the SOFTWARE.

• RECOVERY MEDIA

If SOFTWARE is provided by ALPINE on separate media and labeled “Recovery

Media” you may use the Recovery

Media solely to restore or reinstall the

SOFTWARE originally installed on the

DEVICE.

Continued 137

 Legal Information  User Agreements

138

• UPGRADES

If the SOFTWARE is provided by ALPINE separate from the DEVICE on separate media or via web download or other means, and is labeled “For Upgrade

Purposes Only” you may install one (1) copy of such SOFTWARE onto the

DEVICE as a replacement copy for the existing SOFTWARE, and use it in accordance with this EULA, including any additional EULA terms accompanying the upgrade SOFTWARE.

• TERMINATION

Without prejudice to any other rights,

ALPINE or MS may terminate this EULA if you fail to comply with the terms and conditions of this EULA. In such event, you must destroy all copies of the

SOFTWARE and all of its component parts.

• INTELLECTUAL PROPERTY RIGHTS

All title and intellectual property rights in and to the SOFTWARE (including but not limited to any images, photographs, animations, video, audio, music, text and “applets,” incorporated into the

SOFTWARE), the accompanying printed materials, and any copies of the

SOFTWARE, are owned by MS,

Microsoft Corporation, their affiliates or suppliers. The SOFTWARE is licensed, not sold.

You may not copy the printed materials accompanying the SOFTWARE. All title and intellectual property rights in and to the content which may be accessed through use of the SOFTWARE is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants you no rights to use such content. All rights not specifically granted under this EULA are reserved by

MS, Microsoft Corporation, their affiliates and suppliers. Use of any online services which may be accessed through the SOFTWARE may be governed by the respective terms of use relating to such services. If this

SOFTWARE contains documentation that is provided only in electronic form, you may print one copy of such electronic documentation.

• TRADEMARKS

This EULA does not grant you any rights in connection with any trademarks or service marks of ALPINE MS, Microsoft

Corporation, their affiliates or suppliers.

• PRODUCT SUPPORT

Product support for the SOFTWARE is not provided by MS, its parent corporation Microsoft Corporation, or their affiliates or subsidiaries. For product support, please refer to ALPINE support number provided in the documentation for the DEVICE.

Should you have any questions concerning this EULA, or if you desire to contact ALPINE for any other reason, please refer to the address provided in the documentation for the DEVICE.

• SOFTWARE TRANSFER ALLOWED BUT

WITH RESTRICTIONS

You may permanently transfer rights under this EULA only as part of a permanent sale or transfer of the

Device, and only if the recipient agrees to this EULA. If the SOFTWARE is an upgrade, any transfer must also include all prior versions of the SOFTWARE.

• EXPORT RESTRICTIONS

You acknowledge that SOFTWARE is of

US-origin. You agree to comply with all applicable international and national laws that apply to the SOFTWARE, including the U.S. Export Administration

Regulations, as well as end-user, enduse and country destination restrictions

issued by U.S. and other governments.

For additional information on exporting the SOFTWARE, see http:// www.microsoft.com/exporting/ .

As required by the FCC

1.

This device complies with Part 15 of the

FCC Rules and Canadian RSS-210/

RSSGen. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

2.

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by the party responsible for compliance may void the user’s authority to operate the equipment.

3.

This product emits radio frequency energy, but the radiated output power of this device is far below the FCC and

IC radio frequency exposure limits. This equipment complies with FCC and IC RF radiation exposure limits set forth for an uncontrolled environment. Nevertheless, the device should be used in such a manner that the potential for human contact with the antenna during normal operation is minimized.

 Legal Information  As required by the FCC

139

140

Voice Commands

Voice Commands .................................. 142

Navigation Commands ......................... 142

On-Screen Commands ......................... 144

Spelling Assistance ............................... 144

141

142

Voice Commands

Navigation Commands

The system accepts these commands on a map/guidance screen.

General Commands

Display phone (equivalent to PHONE)

Display audio (equivalent to AUDIO)

Display navigation (if en route, displays the Route screen)

Display information (equivalent to INFO)

Display menu (equivalent to MENU. if en route, displays Route Options)

Display setting (equivalent to SETTING)

Display map

Display map guide (when en route, shows the next guidance point)

Display voice portal (equivalent to d

(Talk) Button)

Cancel

What time is it?

What is today’s date?

Voice help (displays commands for current screen)

Map Display Commands

Display current location (shows current latitude, longitude, and elevation)

Display/Hide (specify icon type):

ATM gas station restaurant post office grocery store lodging (hotel, motel) parking garage parking lot school hospital freeway exit information traffic traffic speeds traffic icons traffic incidents

Go home

Register the current location (stores current location in the Address Book)

Map Scale Commands

Display north up

Display heading up

Display 3D map

Display zoom in

Display zoom out

Display (specify scale):

1/20 mile (80 m) scale

1/8 mile (200 m) scale

1/4 mile (400 m) scale

1/2 mile (800 m) scale

1 mile (1600 m) scale

2 mile (3 km) scale

5 mile (8 km) scale

15 mile (24 km) scale

50 mile (80 km) scale

150 mile (240 km) scale

350 mile (560 km) scale

1000 mile (1600 km) scale

Max zoom in

Max zoom out

Find Place Commands

Find nearest (specify place):

Fuel and auto

Honda dealers

Acura dealers

Gas station

Hydrogen station

Auto parts & electronics

Auto repair & maintenance

Car wash & detailing

Motorcycle dealers

Other car dealers

Roadside assistance

ATM and bank

ATM

Bank

Check cashing

Currency exchange

Community

Business

City hall

Civic center

Convention center

Court house

Higher education

Library

Post office

School

Emergency room

Hospital

Police station

Veterinarian

Lodging

Bed & breakfast

Hotel

Resort

Recreation

Amusement park

Golf course

Historical monument

Marina

Movie theater

Museum

Park

Performing arts

Sports complex

Tourist attraction

Restaurant

ZAGAT restaurant

American restaurant

Californian restaurant

Chinese restaurant

Coffee shop

Continental restaurant

Fast food

 Voice Commands  Navigation Commands

French restaurant

German restaurant

Greek restaurant

Indian restaurant

Italian restaurant

Japanese restaurant

Korean restaurant

Mexican restaurant

Pizza

Seafood restaurant

Thai restaurant

Vegetarian restaurant

Vietnamese restaurant

Other restaurant

Shopping

Shopping area

Accessory store

Book store

Clothing store

Grocery store

Home improvement store

Mall

Office supply store

Pharmacy

Pet food store

Sewing store

Shoe store

Sporting goods store

Continued 143

144

 Voice Commands  On-Screen Commands

Toy store

Travel center

Airport

Automobile club

Bus station

Camping

Commuter rail station

Ferry terminal

Named place

Park & ride

Parking garage

Parking lot

Rental car agency

Rest area

Ski area

Tourist information

Train station

Travel agency

Truck stop

Route Commands

The system accepts these commands when a route is set.

How long to the destination?*

How far to the destination?*

Display destination map

Display entire route

Cancel route

Repeat guidance

* These commands are not available if you scroll through the map while en route to a destination.

On-Screen Commands

The system accepts these commands on any screen. There are over 100 on-screen commands. Say what is written on the screen to activate that selection. For lists, you can say the list item number to select that item.

Next (or Down)

Previous (or Up)

Return

OK (excluding Startup Confirmation screen)

Delete

Spelling Assistance

The voice control system can also recognize phonetic alphabet input for numbers, letters, accented letters, punctuation marks, and symbols.

NOTE:

When selecting letters using the voice control system, a confirmation box may pop up to confirm the entry.

Numbers

Letters

7

8

5

6

9

0

3

4

1

2

Say … Say … or Number …

One

Two

Three

Four

Five

Six

Seven

Eight

Nine

Zero

G

H

E

F

C

D

A

B

K

L

J

I

M

Say … Or say…

Apple/Alpha

Boy/Bravo

Charlie

Dog/Delta

Edward/Echo

Frank/Foxtrot

George/Golf

Henry/Hotel

Igloo/India

John/Juliet

King/Kilo

Larry/Lima

Mary/Mike

 Voice Commands  Spelling Assistance

T

U

R

S

P

Q

N

O

X

Y

V

W

Z

Say … Or say…

Nancy/November

Oscar

Paul/Papa

Queen/Quebec

Robert/Romeo

Sam/Sierra

Tom/Tango

Uncle/Uniform

Victor

William/Whiskey

X-ray

Yellow/Yankee

Zebra/Zulu

Continued 145

 Voice Commands  Spelling Assistance

Accented Letters

Ù

Ú

Ô

Ö

Û

Ü

Say … Say … or Symbol …

O circumflex

O umlaut

U grave

U acute

U circumflex

U umlaut

Symbols

146

É

Ê

Ç

È

Â

Ä

À

Á

Ï

Î

Í

Ë

Ó

Say … Say … or Symbol …

A grave

A acute

A circumflex

A umlaut

C cedilla

E grave

E acute

E circumflex

E umlaut

I acute

I circumflex

I umlaut

O acute

:

-

*

+

$

#

?

!

/

;

@

&

~

Say … Say … or Symbol …

Question mark

Exclamation point

Dollar

Pound

Asterisk

Plus

Hyphen

Colon

Semicolon

Slash

At sign

Ampersand

Tilde

»

`

^

<

>

%

_

¡

¿

)

(

«

,

.

Say … Say … or Symbol …

Dot

Double quote

Comma

Apostrophe

Open parenthesis

Close parenthesis

Inverted exclamation point

Inverted question mark

Left-Pointing Double Angle

Quotation Mark

Right-Pointing Double

Angle Quotation Mark

Percent

Underscore

Less than

Greater than

Caret

Back quote

 Voice Commands  Spelling Assistance

147

148

List of Categories

All Types

Acura Dealers

Honda Dealers

Fuel/Auto

Auto Repair & Maintenance

Car Wash & Detailing

Motorcycle Dealers

All Types

Bed & Breakfast

Lodging

Hotel/Motel

Resort

Recreation

Shopping

All Types

Accessories/Jewelry

Auto Parts & Electronics

Mall/Department Store

Office Supplies/Electronics

Pharmacy/Drug Store

Gas Station

Hydrogen Station

Auto Parts & Electronics

All Types

ATM

Other Car Dealers

Roadside Assistance

ATM/Bank

Check Cashing/Money Transfer Marina

Currency Exchange

All Types

Amusement Park

Museum Books/Music/Video

Park/Recreation Area Clothing

Golf Course Performing Arts

Historical Monument Sports Complex

Tourist Attraction

Shoes/Bags

Groceries

Home Improvement

Movie Theater Travel

Pet Food/Supplies

Sewing/Linen

Sporting Goods

Toys/Arts/Crafts

Bank

Community All Types

Restaurant

Indian

All Types

Airport

Parking Garage/House

Parking Lot

All Types

Business

Court House

Higher Education

City Hall Library

Civic/Community Center Post Office

Convention/Exhibition Center School

Emergency

All Types

Hospital

Police Station

Roadside Assistance

Veterinarian

All Types (Zagat Only) Italian

American Japanese

Café/Coffee shop

Californian

Chinese

Continental

Korean

Mexican

Pizza

Seafood

Fast Food

French

German

Greek

Thai

Vegetarian

Vietnamese

Other

Automobile Club

Bed & Breakfast

Bus Station

Camping

Commuter Rail Station

Ferry Terminal

Hotel/Motel

Named Place

Park & Ride

Rental Car Agency

Resort

Rest Area

Ski Area

Tourist Attraction

Tourist Information

Train Station

Travel Agency

Truck Stop/Plaza

Index

Symbols a

(Display Mode) Button ...................... 54

J

(Hang-Up/Back) Button

................5, 20

d

(Talk) Button ......................................5, 20

Numerics

3D Angle Adjustment ................................. 57

A

Address

Editing Address Book ................................. 25

Editing Avoid Area ..................................... 41

Setting Destination ..................................... 70

Address Book

Editing Address Book ................................. 23

Setting Destination ..................................... 76

Address Book PIN

........................................ 28

ATM/Bank (Place Category)

....................... 78

Avoid Streets

.............................................. 114

Avoided Area ............................................... 40

C

Call ................................................................. 92

Cancel Route

.............................................. 107

Category

Editing Address Book ................................. 25

Place Category List ................................... 148

Setting Destination ..................................... 78

Category History

Deleting ...................................................... 30

Change State ................................................ 71

City

.................................................................72

City Vicinity

Setting Destination .....................................79

Color

Day ..............................................................53

Night ...........................................................53

Community (Place Category) .....................78

Continue Trip .............................................118

Coordinate ....................................................91

Correct Vehicle Position ..............................64

Current Location ..........................................58

Current Position

Editing Address Book .................................25

Setting Destination .....................................89

D

Day Mode

Switching Display Mode .............................54

Delete Tracking

............................................63

Destination List

Adding Waypoint .....................................108

Editing .......................................................112

Detour

.........................................................114

Directions ....................................................102

Display Tracking

...........................................63

Driving ........................................................97

Setting ........................................................63

Download POI

Editing Category .........................................32

Importing Category ....................................31

Setting Destination .....................................86

E

Edit Go Home .............................................. 27

Edit Home Entry

.......................................... 92

Edit POI Search Radius Along Route

........ 39

Edit/Delete Entry ......................................... 92

Emergency (Place Category)

...................... 78

ENT Button ..................................................... 6

Error Messages .......................................... 126

Navigation System ................................... 126

Estimated Time ............................................ 48

Exit Info ...................................................... 103

F

Fuel/Auto (Place Category)

........................ 78

G

Go Home

...................................................... 10

Go Home PIN ............................................... 28

Guidance (Navi Settings)

............................ 42

Guidance Mode

........................................... 43

Guidance Point

............................................ 47

H

Home Address

....................................... 10, 27

Honda Automobile Customer Service

Contact Information

................................ 132

House Number

............................................. 75

149

150

 Index

I

Interface Dial

..................................................6

Intersection ...................................................88

L

Lodging (Place Category) ...........................78

M

Map (Navi Settings)

.....................................49

Map Data Update

Obtaining Update Data ............................133

Map Input

Editing Avoid Area ......................................41

Setting Destination .....................................89

Map Legend

..............................................8, 59

Map Menu

..................................................100

Map Screen

...................................................94

Changing View ...........................................56

Icon .........................................................8, 61

Scale ............................................................60

Map/Guidance

............................................101

MENU Button

Changing Route .......................................106

Entering a Destination ................................68

N

NAV Button

..............................................9, 43

Navigation Menu (Destination)

.................68

Navigation Menu (Route Option)

...........106

Next Maneuver Pop up ...............................46

Night Mode

Switching Display Mode ............................ 54

P

Personal Info

................................................ 22

PIN Numbers ................................................ 28

Place Category

Editing Address Book ................................. 25

Place Category List ................................... 148

Setting Destination .................................... 78

Place Name

Editing Address Book ................................. 25

Setting Destination .............................. 79, 80

Place Phone Number

Editing Address Book ................................. 25

Setting Destination .................................... 83

Previous Destinations

Deleting ...................................................... 29

Editing Address Book ................................. 25

Setting Destination .................................... 77

R

Recreation (Place Category) ...................... 78

Restaurant (Place Category)

...................... 78

Route Option ............................................. 106

Route Preference

........................................ 35

Routing

......................................................... 34

S

Scenic Route

................................................. 87

Search Along .............................................. 109

Search Around

........................................... 109

Search by Name ........................................... 79

Search Nearby ............................................ 115

Security PIN Code ...................................... 128

SETTINGS Button

........................................... 4

Shopping (Place Category) ......................... 78

Show Icon on Map ...................................... 51

Sort by Distance to Travel

.......................... 79

Straight Line Guide ..................................... 57

Street

............................................................. 73

Street Name Guidance ................................ 45

System Device Information ........................ 65

T

Traffic Incidents ......................................... 104

Traffic List ................................................... 104

Traffic Rerouting

....................................... 104

Auto Reroute ............................................ 104

Navi Settings ............................................... 38

Travel (Place Category) ............................... 78

U

Unverified Routing

...................................... 36

Update System Software

Finding Update Information ..................... 133

Obtaining Update Data ............................ 133

V

Vehicle

Correct Vehicle Position ............................. 64

Off-road Tracking ....................................... 63

View (Navi Settings) .................................... 56

View Area Map

............................................ 40

View Routes

................................................. 93

Voice

Map Menu .................................................. 98

Voice Commands

Basic Operation ............................................ 7

Help ............................................................ 13

Voice Commands List ............................... 142

Voice Control System ................................. 20

Voice Control Operation

Basic Operation ............................................ 5

Voice Portal .................................................. 5

W

Waypoint

Adding ...................................................... 108

Deleting, Ordering .................................... 112

Z

ZAGAT

Displaying Review ....................................... 85

Setting Destination ..................................... 83

Zip Code

........................................................ 71

 Index

151

advertisement

Key Features

  • Voice control for hands-free operation
  • 13 different methods to enter a destination
  • FM Traffic to bypass congestion and traffic incidents
  • Set up to 4 waypoints along your route for planned stops
  • Avoid certain areas to detour around construction or closures
  • Store up to 200 contacts in the address book

Frequently Answers and Questions

How do I get started with the Honda Crosstour?
Press the NAV button to start up the system.
Can I use voice commands to control the system?
Yes, you can use voice commands to control all key functions of the navigation system.
How do I enter a destination?
You can enter a destination using 13 different methods, including address, intersection, place name, and phone number.
Can I avoid certain areas on my route?
Yes, you can set streets and areas to detour around.
Can I add stops along my route?
Yes, you can add up to 4 waypoints along your route.

Related manuals

Download PDF

advertisement

Table of contents