Data sheet
OSP60 / OSI-S / OMM-S www.renishaw.com/SPRINT
Specification
System principal application High-speed scanning system for on-machine process control.
OSP60 (probe) Analogue scanning probe for machine tools, capable of both 3D scanning and 3D discrete
OMM-S (receiver)
OSI-S (interface) point measurements.
Optical receiver specific to the OSP60 probe.
Interface that processes data from the OMM-S and provides input/output communication with the machine tool.
Infrared optical transmission: up to 1000 3D points per second.
Transmission type
Probe transmission range
Probe turn-on time
Probe weight (without shank) with batteries
Battery type
Battery life typical at 20 °C
Full power
Low power ( ⅛ )
Scanning measurement range
(see note 2)
Sensor type
Sense directions
Sensor resolution (µm/digit)
360°. Up to 4.5 m (14.7 ft) with one receiver, or up to 9 m (29.5 ft) with two receivers.
Less than 0.5 seconds
1080 g (38.1 oz)
3 × CR123 3 V lithium-manganese dioxide
Standby
121 days
Omnidirectional ±X, ±Y, ±Z.
5% usage
320 hours
Full 3D (simultaneous XYZ data output)
(see note 1)
121 days
±X, ±Y, ±Z 0.50 mm (0.020 in)
620 hours (see note 1)
XY 0.025 µm (0.9843 µin); Z 0.004 µm (0.1575 µin)
Continuous life
16 hours
31 hours
(see note 3)
Maximum speed (see note 4) Scanning up to rapid (G0) feedrate, dependent on machine tool performance and application.
Stylus length range 75 mm to 150 mm (2.95 in to 5.90 in) recommended.
Stylus ball diameter range
Stylus type
2 mm to 8 mm (0.078 in to 0.31 in) typical.
Straight styli only. OSP60-specific styli recommended. For further information, see the information leaflet Styli recommendations for OSP60 scanning probes
(Renishaw part no. H-5465-8102).
Spring rate (see note 3) Measuring force (see notes 3 and 5)
0.8 N/mm (4.57 lb/in) 0.1 N 10 gf (0.4 ozf)
Stylus force
XY (typical)
Z (typical)
Sealing
OSP60/OMM-S
OSI-S
Operating temperature
OMM-S cable
1.5 N/mm (8.57 lb/in)
IPX8
IP20
0.2 N 20 gf (0.7 ozf)
BS EN 60529:1992+A2:2013 (IEC 60529:1989+A1:1999+A2:2013).
+5 °C to +55 °C (+41 °F to +131 °F)
The OMM-S is supplied with a 15 m (49 ft) cable.
Cable specification: Ø6.1 mm, 8-core, twisted pair, screened cable, each core
Controller compatibility
7 × 0.146 mm. Maximum cable length 30 m (98 ft).
Mounting
OMM-S A mounting bracket is available allowing directional setting.
OSI-S
OSI-S supply
DIN rail or alternative mounting screws.
18 Vdc to 30 Vdc 500 mA @ 24 V nominal 4 A peak. Supply must conform to
OSI-S output signal
BS EN 60950-1:2006+A2:2013 (IEC 60950-1:2005+A2:2013).
Voltage-free solid state relay (SSR) output, configurable normally open or normally closed.
‘On’ resistance = 50 Ω max. Load voltage = 50 V max. Load current = 60 mA max.
OSI-S input/output protection Power input is protected by a 1.85 A resettable fuse.
Turning on the power supply will reset the OSI-S.
Please contact Renishaw for system compatibility requirements.
Note 1
Note 2
Note 3
Note 4
Note 5
Calculated value.
Maximum allowed distance between the nominal scan line and the actual scan line. Full 3D performance on a vertical machining centre with a 75 mm stylus.
In some applications, this range can be extended. Contact your local Renishaw representative for more information.
Typical for a 100 mm stylus.
Maximum feedrate for over deflection protection is F40000 in Z and F60000 in XY.
Force at which the status signal changes for touch trigger. Assumes a trigger threshold of 0.125 mm (0.0049 in).
Data sheet
OSP60 dimensions
100 (3.94)
M4 stylus
13.6 (0.54)
Battery cassette
A range of probe-ready shanks are available from Renishaw
4.8°
4.8°
Dimensions given in mm (in)
Window
100.6 (3.96)
Probe status LED
Stylus length
75 (2.95)
Stylus overtravel limits
±X / ±Y +Z
7 (0.28) 6 (0.24)
100 (3.94)
150 (5.91)
9 (0.35) 6 (0.24)
13.5 (0.53) 6 (0.24)
− Z
2.2 (0.09)
2.2 (0.09)
2.2 (0.09)
OMM-S dimensions
84 (3.30)
40 (1.57) 40 (1.57) 46.7 (1.84)
5.5 (0.22)
OMM-S mounting bracket (optional)
3 holes Ø6.5 (0.26)
25
(0.98)
25
(0.98)
3 grip protrusions
100.5 (3.95)
Dimensions given in mm (in)
16 (0.63)
2 (0.08)
3 pairs of holes Ø5.5
(0.22) permit OMM-S mounting in alternative orientation
Dimensions given in mm (in)
45 (1.77)
90 (3.54)
45°
OSI-S dimensions
151.4 (5.96)
151.4 (5.96)
Dimensions given in mm (in)
Transmission performance envelope
The system performance envelope and range is shown below.
The system components should be positioned so that the optimum range can be achieved over the full travel of the machine’s axes, taking into account likely part positions on a moving machine table. The system uses optical infrared transmission and requires line-of-sight.
When possible, the optical power of the probe can be reduced to maximise battery life and the optical power of the receiver can be reduced to prevent interference with systems on adjacent machines.
75° 75°
60° 60°
45° 45°
30° 30°
15° 15°
OSP60
1.0
(3.3)
2.0
(6.5)
3.0 (9.8)
4.0 (13.1)
5.0 (16.4)
75°
Typical plot at +20 °C (+68 °F)
360° around probe axis in m (ft)
60°
45°
30°
0°
15°
Optical centre line
0°
15°
Power level settings
Full power
½ power
¼
power
⅛ power
30°
45°
60°
1.0
(3.3)
2.0 (6.5)
3.0 (9.8)
4.0 (13.1)
75°
5.0 (16.4)
OMM-S
Renishaw plc
New Mills, Wotton-under-Edge
Gloucestershire, GL12 8JR
United Kingdom
T +44 (0)1453 524524
F +44 (0)1453 524901
E [email protected]
www.renishaw.com
Spare parts and accessories
A full range of spare parts and accessories is available.
Please contact Renishaw for a full list.
For worldwide contact details, visit www.renishaw.com/contact
RENISHAW HAS MADE CONSIDERABLE EFFORTS TO ENSURE THE CONTENT OF THIS DOCUMENT IS CORRECT
AT THE DATE OF PUBLICATION BUT MAKES NO WARRANTIES OR REPRESENTATIONS REGARDING THE CONTENT.
RENISHAW EXCLUDES LIABILITY, HOWSOEVER ARISING, FOR ANY INACCURACIES IN THIS DOCUMENT.
© 2015–2019 Renishaw plc. All rights reserved.
Issued 07.2019
*H-5465-8200-05*
