Xerox 180MX DocuPrint User Guide

Duty cycle
Speed
Controller components
Interface requirements
Targeted impressions per month on the Xerox
DocuPrint 2000 Series 100/115/135/155/180 EPS:
The speed at which data can be printed on the Xerox
DocuPrint 2000 Series 100/115/135/155/180 EPS:
• Processor (system unit):
One or more of the following network communications
systems may be used to transport documents from a
client or host to the printing system.
Printing system
Minimum
Maximum
DP100
800 thousand
3 million
Printing system
Pages per minute
(standard)
DP115
1 million
3.5 million
DP100
100
100
DP135
1.2 million
4 million
DP115
115
115
DP155
1.4 million
4.5 million
DP135
135
154
DP180
1.8 million
6 million
DP155
155
155
DP180
180
206
Note: Usage outside these ranges may vary the
service frequency.
Note: Throughput rates can vary depending upon job
complexity and system configuration.
Performance
Reliability performance of the Xerox DocuPrint 2000
Series 100/115/135/155/180 EPS for the targeted
impressions per month:
Average
monthly
print
volume
1
million
* Requires optional 7 by 10 inch enablement kit
Paper handling
• Paper weights: 16 lbs / 65 gsm bond to 110 lbs /
Average
service
calls per
month
DP100
Average
service
calls per
month
DP115
Average
service
calls per
month
DP135
Average
service
calls per
month
DP155
Average
service
calls per
month
DP180
2.7
2.6
2.5
2.6
2.4
— 8 by 10 in / 203 by 254 mm to
14.33 by 17 in / 364 by 432 mm, including A4
and A3
4.8
— 7 by 10 in / 178 by 254 mm with optional 7 by
10 in enablement kit
2
million
5.4
3
million
8.1
5.2
7.8
5.0
7.5
5.2
7.8
7.2
— One or two UltraSPARC III 750 Mhz central
processing unit (CPU) modules
Pages per minute
(using 7 by 10 in /
178 by 254 mm
paper) *
200 gsm index cut-sheet weights
• Paper sizes:
Input
— 1 or 2 GB of memory (one or two 1-GB Dual Inline Memory Modules, or DIMMs)
— 36 GB hard disk drive
— High-density, read-only DVD-ROM drive
— Diskette drive: uses 3.5 inch, 1.44 MB, doublesided, high-density diskettes
— Ethernet
— Two Printer Controller Interface (PCI) boards
— PGx64 video graphics board
--
5
million
--
6
million
--
--
10.0
10.4
9.6
---
---
---
12
Supported client workstations
Xerox DP 2000 Series 100/115/135/155/180 EPS
supports the following types of networked client
workstations and operating systems:
• Sun Workstation running Solaris 2.3 or higher
• PC running MS-DOS 5.0 or higher, using Ethernet
with TCP/IP or Novell NetWare, Windows 95/98,
Windows NT, or Windows 2000
• PC 386 or 486, running MS-DOS 5.0 or higher, with
one or more of the following TCP/IP packages:
• Auxiliary tray (Tray 2): 600 sheet capacity of 20 lbs /
14.4
Note: Variables other than monthly print volume affect
the average number of service calls. Please contact
your local Xerox representative for more information.
The Xerox DocuPrint 2000 Series 100/115/135/155/
180 EPS may have up to six input trays: two processor
trays and two, three, or four high-capacity feeder trays.
DP 155 and 180: 600 by 2400 dots per inch (dpi).
DP 100, 115, and 135: 600 by 600 dots per inch (dpi)
Refer to Helpful Facts About Paper to help in selection
of preprinted forms, perforated stock and labels.
• Data Cable: The controller can be separated up to
the length of the data interface cables that connects
them.
• Apple Macintosh, System 7 (7.6.1 or higher), using
AppleTalk through EtherTalk
• Any system that supports RFC-1179 lpr/lpd
•
•
•
•
•
•
•
•
•
—
20 foot / 6.1 meters, or
—
optional 50 foot / 15.2 meters
Power cable lengths are as follows:
Controller:
Printer:
8 feet / 2.4 m
15 feet / 4.6 m
• Cable length loss must be factored in if equipment is
installed in a raised-floor environment. Part of the
cable length is routed inside the equipment to
connect with interior power receptacles.
• All power cords attach to the back of the printer.
Listed below are the distances of the printer power
cord attachments from the left end of the printer as
you face it:
— Cord #2: 23 inches / 584 mm (DP 155 & 180)
3. PC-NFS by Sun Select
The system interprets the following data formats:
• Sample tray: 100 sheets of 20 lbs / 80 gsm bond
Installation considerations
— Cord #1: 36 inches / 914 mm
PDL compatibility
Resolution
AppleTalk network protocol software.*
* Requires additional equipment.
2. Pathway Access by Wollongong Group, Inc.
• Output bin: Each output bin has a capacity of 2500
Two output bins are standard, with up to two
additional bins available as options.
• Token ring LAN running TCP/IP, Novell 3.x, or
1. PC/TCP Network Software by FTP Software, Inc.
Output
sheets of 20 lbs / 80 gsm bond with offset capability.
interface.*
Note: This configuration may change due to the Xerox
policy of staying up to date with current technology.
• Main tray (Tray 1): 1100 sheet capacity of 20 lbs / 80
80 gsm bond paper
NetWare network protocol software.
• Online - Bus and tag supporting IBM 3211/4245
• Universal Serial Bus (USB) keyboard and mouse
• 17.4-inch flat panel monitor
gsm bond paper
4
million
• Ethernet LAN running TCP/IP, AppleTalk, or Novell
PostScript levels 2 and 3
PCL5e
LCDS
IPDS (requires additional equipment)
ASCII
PDF
TIFF
VIPP
Special considerations
• Transference of the black toner to poly-vinyl
surfaces is a common occurrence.
• When printing edge to edge, there is a 3 to 4.8 mm
border around the sheet where degraded image
quality may occur.
• Edge marking should be no closer than 4.8 mm from
the edge of the sheet.
• Xerox carbonless paper is approved for Xerox
DocuPrint 2000 Series 100/115/135/155/180 EPS.
Refer to the Xerox Supplies Catalog for the reorder
numbers.
• Appearance of very small spots is a common
occurrence on all xerographic printers. Consult your
Xerox service representative for details on
acceptable spot occurrence specifications.
Environmental requirements
Recommended
72o
4o
Operating
+/F
temperature 22o +/- 2o C
Humidity
Minimum
oF
50
10o C
45% +/- 10% RH 30% RH
Altitude
Maximum
o
85 F
29o C
65% RH
Normal
Maximum
Up to 6,000
feet / 1,830 m
above sea lvl.
9,000 feet /
2,743 m
above sea lvl.
Depth
Heat dissipation
Standby
Running
Printer
4,454 BTU/Hr
(Fuser on)
2,700 BTU/Hr
(Energy saver)
155/180:
32,770 BTU/hr
100/115/135:
28,140 BTU/hr
1,100 BTU/Hr
Supplies
Reorder number
Expected yield
(Prints/carton)
Dry ink
US: 6R206
Europe: 6R90100
180,000
Dry ink waste
bottle
US: 93K460
Europe: 93K450
N/A
Developer
US: 5R161
Europe: 5R90095
1,000,000
Fuser agent
US: 8R2955
Europe: 8R90163
250,000
(1 bottle)
MICR dry ink
US: 6R819
180,000
MICR
developer
US: 5R573
the printer.
Width
Height
Controller
The following data is accurate for the Sun Blade 1000
workstation and is presented as an example of typical
space requirements for workstations.
Stand
35.5 in
90.2 cm
30 in
76.2 cm
38.25 in
97.2 cm
Processor
25 in
63.5 cm
10 in
25.4 cm
17.75 in
45.1 cm
10 in
25.4 cm
17.5 in
44.5 cm
18.5 in
47 cm
Monitor
Processor and
monitor
• 50 in / 127 cm clearance space is required in front of
Space requirements
Printer
Space requirements (physical hardware and required
service area) for each of the printer configurations:
With inverter feeder/ 114 in
stacker and
290 cm
one (1) feeder/
stacker
223 in
567 cm
With inverter feeder/ 114 in
stacker and
290 cm
two (2) feeder/
stackers
257 in
652.8 cm
With inverter feeder/ 114 in
stacker and
290 cm
three (3) feeder/
stackers
288 in
731 cm
With inverter feeder/ 114 in
stacker, feeder/
290 cm
stacker, and bypass
transport module
242 in
615 cm
With inverter feeder/ 114 in
stacker and two (2) 290 cm
feeder/stackers, and
bypass transport
276 in
701 cm
• The controller must be positioned within the line of
sight of the printer for safety purposes while the
equipment is being serviced.
• Customer must use the Xerox-supplied stand for all
controller components. Space requirements for the
controller stand are 36 by 36 inches / 91 by 91 cm.
Xerox DocuPrint 2000
Series 100/115/135/155/
180 EPS
• For proper operation, the printer must be perfectly
level. On floors less than two degrees out of level, a
leveling kit must be used to level the equipment.
The printer will not function properly on floors more
than two degrees out of level.
For additional space/configuration options, refer to the
Xerox DocuPrint 2000 Series 100/115/135/155/180
EPS Installation Planning Guide.
Customer Information
Quick Reference Card
Electrical requirements
Controller
(47-63 Hz)
Voltage
Printer
(60 Hz)
Cord #1
100-240 120/208
VAC
VAC; or
(1 phase) 120/240
VAC
(2 phase)
155/180
printer
(60 Hz)
Cord #2
Printer
(50 Hz)
120/208 380, 400,
VAC; or 415 VAC
120/240 (3 phase)
VAC
(2 phase)
Recep5-15R
tacle
NEMA part
number
14-50R
14-30R
--
Power
0.4
consumption (KVA)
Operating
mode
7.3 +
.75 per
middle
module
stacker
7.3+
.75 per
middle
module
stacker
Consult
your local
Service
Represen
tative
Notes:
• Dedicated service is required for each component.
Each power cord must have a separate circuit.
• Power requirements of the bypass transport are
600,000
Notes:
satisfied by the printer module.
• All the dimensions are taken from the system frame
Notes:
• Expected dry ink yield is based on a 7 percent area
coverage, 8.5 by 11 inch or A4 paper, and will vary
depending on area coverage of the application, as
well as the darkness settings of the printer.
• Contact your local Xerox representative for supplies
ordering information.
• In the U.S., call 1.800.822.2200 to order Xerox
supplies, including paper and other stocks.
to the nearest wall or obstruction, shown in inches
and centimeters, and are absolute minimums.
• There should be a minimum of 78 inches / 198 cm
clearance from the floor to the nearest overhead
obstruction, throughout the entire area.
• The printing system must be installed in a fixed
location with minimum clearance space of 36 inches
/ 91.4 cm around all sides of each piece of
equipment for access by service personnel.
2002 by Xerox Corporation. All rights reserved.
Version 3.6
October 2002
701P21150

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project