Steren STV-065 Soporte de techo para pantallas de 32” a 65” Owner's Manual
Steren STV-065 is a ceiling mount designed for 32" to 65" TVs weighing up to 40 kg. It features a telescopic bar for height adjustment, a tilt mechanism for optimal viewing angles, and a sturdy construction for secure installation. The mount includes all necessary hardware for mounting to concrete ceilings. With its easy installation process and versatile design, the Steren STV-065 is a great choice for mounting your TV in your home or office.
Advertisement
Advertisement
STV-065
Manual de instrucciones
HERRAMIENTAS NECESARIAS PARA LA INSTALACIÓN
0119m V1.0
IMPORTANTE
Antes de utilizar el producto, lee cuidadosamente este manual para evitar cualquier mal funcionamiento.
La información presentada sirve únicamente como referencia sobre el producto; debido a actualizaciones pueden existir diferencias.
Consulta nuestra página web www.steren.com
para obtener la versión más reciente de este manual.
PRECAUCIONES
• Este aparato no se destina para utilizarse por personas (incluyendo niños) cuyas capacidades físicas, sensoriales o mentales sean diferentes o estén reducidas, o carezcan de experiencia o conocimiento.
• Los niños deben supervisarse para asegurar que no empleen el aparato como juguete.
• Este producto está diseñado para uso en interiores.
• El soporte debe ser instalado sobre una superficie sólida.
• No debe excederse la capacidad de carga máxima (40 kg).
CONTENIDO
PIEZAS
Barras de sujeción
(2 piezas)
Soporte de pantalla
(1 pieza)
Soporte de techo
(2 segmentos)
Barra telescópica
(2 segmentos)
Nivel
(1 pieza)
TORNILLOS
M4x20 mm
A (4 piezas)
M6x20 mm
B (4 piezas)
M8x25 mm
C (4 piezas)
RONDANAS, BUJES, TUERCAS Y TAQUETES
M6x8 mm
D (2 piezas)
M8
E (4 piezas)
M6x40 mm
F (4 piezas)
M6
G (4 piezas)
M6
H (4 piezas)
M8
I (4 piezas)
M8
J (4 piezas)
M6
K (4 piezas)
M8
L (4 piezas)
INSTALACIÓN
1 Utiliza el soporte de techo como plantilla para realizar las marcas de las perforaciones en el lugar donde deseas instalarlo.
Selecciona 2 orificios de cada lado.
2 Realiza las perforaciones a una profundidad de 60 mm, con una broca de 10 mm de diámetro.
60 mm
ø10 mm
3 Ensambla el soporte de techo y el primer segmento de la barra telescópica, como se muestra en la figura.
4 Introduce los taquetes (L) en los orificios realizados, y fija la pieza con los tornillos (E) y las rondanas (I) .
I
E
L
Steren no se hace responsable por daños materiales ni personales causados por mal uso o mala instalación. Es responsabilidad del usuario asegurarse de la correcta instalación y uso del producto, así como de su revisión periódica.
D
5
F
Complementa la barra telescópica, con el segundo segmento y el soporte de pantalla a la altura deseada. Fija ambas piezas usando los tornillos (F) , las rondanas (H) y las tuercas (K) .
F
K
H K
H
6 Utiliza 4 tornillos (A o B) , los 4 bujes separadores (J) y las 4 rondanas (G) para fijar las barras en la parte posterior de la pantalla. En caso de requerir tornillos más anchos, sólo utiliza los tornillos (C) y los bujes separadores (J) , sin las rondanas.
J
G
A,B o C
Observa que la burbuja esté en el centro, para corroborar que el soporte esté nivelado
No instales pantallas de más de 65” ni con un peso mayor a 40 Kg
Los tornillos suministrados son de medidas estándar. Te recomendamos consultar el manual de instrucciones de tu pantalla para obtener información acerca de los tornillos necesarios para montarla en un soporte.
7 Afloja los tornillos de sujeción, y monta la pantalla sobre el soporte colocando primero la parte superior de las barras (en forma de gancho) y, posteriormente, la parte inferior.
Ajusta la inclinación de la pantalla, al aflojar y apretar las mariposas Afloja los tornillos (D) para girar la pantalla. Vuelve a apretarlos para que quede fija
D
Aprieta los tornillos para fijar la pantalla
Asegúrate de que las barras queden perfectamente acopladas
Ajusta la altura quitando los tornillos (F) y las tuercas (K)
F K
NECESSARY TOOLS FOR INSTALLATION
STV-065
32” TO 65” CEILING MOUNT
Instruction manual
0119m V1.0
IMPORTANT
Before using the product, read this manual carefully to avoid any malfunction.
The information presented serves only as a reference on the product; Due to updates there may be differences.
Check our website www.steren.com
for the latest version of this manual.
CAUTIONS
• This device is not intended for use by persons (including children) whose physical, sensory or mental abilities are different or reduced, or who lack experience or knowledge.
• Children should be supervised to ensure they do not use the device as a toy.
• This product is designed for indoor use.
• The support must be installed on a solid surface.
• The maximum load capacity (40 kg) must not be exceeded.
INSTALLATION
1 Use the ceiling stand as a template to make the perforation marks in the place where you want to install it. Select 2 holes on each side.
2
CONTENT
PIECES
Holding bars
(2 pieces )
TV stand
(1 piece)
Ceiling stand
(2 segments)
Telescopic bar
(2 segments)
Level
(1 piece)
SCREWS
M4x20 mm
A (4 pieces)
M6x20 mm
B (4 pieces)
M8x25 mm
C (4 pieces)
WASHERS, HUBS, NUTS AND ANCHORS
M6x8 mm
D (2 pieces)
M8
E (4 pieces)
M6x40 mm
F (4 pieces)
M6
G (4 pieces)
M6
H (4 pieces)
M8
I (4 pieces)
M8
J (4 pieces)
M6
K (4 pieces)
M8
L (4 pieces)
Perform the holes to a depth of 60 mm, with a drill of 10 mm in diameter.
60 mm
ø10 mm
4 Insert the anchors (L) into the holes made, and fix the part with the screws (E) and the washers (I) .
3 Assemble the ceiling stand and the first segment of the telescopic bar, as shown in the figure.
I
E
L
Concrete ceiling
Steren is not responsible for material or personal damages caused by misuse or improper installation. It is the responsibility of the user to ensure the correct installation and use of the product, as well as its periodic review.
D
5 Complements the telescopic bar, with the second segment and the screen support at the desired height. Fix both parts using the screws (F) , the washers (H) and the nuts (K) .
F
F
K
H K
H
Observe that the bubble is in the center, to verify that the support is level
6 Use 4 screws (A or B) , the 4 hub spacers (J) and the 4 washers (G) to fix the bars on the back of the screen. If you require wider screws, only use the screws (C) and the hub spacers
(J) , without the washers.
J
G
A,B o C
Do not install screens over 65 "or weighing more than 40 Kg
The screws supplied are standard sizes. We recommend you consult the instruction manual of your screen to obtain information about the screws necessary to mount it in a support.
7 Loosen the fixing screws, and mount the screen on the support by first placing the upper part of the bars (in hook form) and then the lower part.
Adjust the tilt of the screen, by loosening and tightening the butterflies Loosen the screws (D) to rotate the screen. Tight them so that it stay fixed
D
Tighten the screws to fix the screen Adjust the height by removing the screws (F) and the nuts (K)
Make sure that the bars are perfectly coupled F K

Public link updated
The public link to your chat has been updated.
Advertisement