Aplex AEx-819P ATEx Certificate User Manual

Add to my manuals
78 Pages

advertisement

Aplex AEx-819P ATEx Certificate User Manual | Manualzz
AEx-8XXP(H)
15”, 15.6”, 19”, and 21.5” Full IP66 Stainless Steel Designed with M12 waterproof
connector of Panel PC Series.
User Manual
Release Date
Revision
Aug. 2019
V1.5
®2019 Aplex Technology, Inc.
All Rights Reserved.
Published in Taiwan
Aplex Technology, Inc.
15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan
Tel: 886-2-82262881
Fax: 886-2-82262883
URL: http://www.aplextec.com/zh/home.php
Revision History
Reversion
Date
Description
0.1
2017/11/24
For Preliminary Release
1.0
2018/01/02
Official version
1.1
2018/03/27
Modify power pin defined
1.2
2018/05/16
Modify power pin description
1.3
2018/06/22
Add Warning
1.4
2018/10/12
Revise specification wording
1.5
2019/08/28
Modify MB information
AEx-8XXP(H) Series User Manual
1
Warning!___________________________
This equipment generates, uses and can radiate radio frequency energy and if
not installed and used in accordance with the instructions manual, it may
cause interference to radio communications. It has been tested and found to
comply with the limits for a Class A computing device pursuant to FCC Rules,
which are designed to provide reasonable protection against such interference
when operated in a commercial environment. Operation of this equipment in
a residential area is likely to cause interference in which case the user at his
own expense will be required to take whatever measures may be required to
correct the interference.
Electric Shock Hazard – Do not operate the machine with its back cover
removed. There are dangerous high voltages inside.
If you need to connect or reconnect M12 cables, please make sure turning off
the power before all the replacement procedures and must in normal
environment, Recommend use ATEx certificated IO cables.
Disclaimer
This information in this document is subject to change without notice. In no event
shall Aplex Technology Inc. be liable for damages of any kind, whether incidental or
consequential, arising from either the use or misuse of information in this
document or in any related materials.
AEx-8XXP(H) Series User Manual
2
ATEX Instruction Guide
SAFETY INSTRUCTIONS
Read these instructions carefully, and look at the equipment to become familiar with
the device before trying to install, operate, or maintain it. The following special
messages may appear throughout this documentation or on the equipment to warn
of potential hazards or to call attention to information that clarifies or simplifies a
procedure.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by
qualified personnel. No responsibility is assumed by Digital Electronics Corporation
for any consequences arising out of the use of this material. A qualified person is one
who has skills and knowledge related to the construction and operation of electrical
equipment and its installation, and has received safety training to recognize and
avoid the hazards involved.
SCOPE
This present document applies when AEx-8XXP(H) Series bears
marking. They
are supplied only with DC 9~36 V. This documentation has to be kept and always
refer to those instructions for installation, operation, maintenance or evolution of
your system.
Permitted zones of application
Refer to the section titled "Markings" to get information about the permitted zones
of protection and the types of protection.
• AEx-8XXP(H) Series is installed in zones 2 hazardous areas must be certified and
bear the
marking.
• Ensure with the marking that the terminals are compatible with the conditions
permitted for the hazardous area at the site where it is being used.
AEx-8XXP(H) Series User Manual
3
Notice
1. Under certain extreme circumstances, the label may generate an
ignition-capable level of electrostatic charge. Therefore the equipment shall not
be installed in a location where the external conditions are conducive to the
build-up of electrostatic charge on the label. In addition, the label shall only be
cleaned with a damp cloth.
2. Warning – in locations where high external humidity and internal temperature
variations (e.g. frequent on-off cycles) may cause condensation inside the
equipment, the interior should be periodically inspected.
3. When the device is mounted in a hazardous area, connection and
disconnection of external connectors while live is only permitted if the potentially
explosive atmosphere is shown to be absent.
4. The “9-36” Vdc rated supply shall be protected such that transients are limited
to a maximum of 119 V; no such protection is required for the signal lines.
5. Equipotential bonding facilities on the outside of enclosure are assessed as
providing effective connection of a conductor with a cross-sectional area of at least
4 mm2, 10AWG, 600V wire
6. The equipment is suitable for use in class I, division 2, groups A, B, C, D OR
non-hazardous locations only.
7. Warning- Do not use USB while the circuit is live unless the area is known to
be non-hazardous.
Markings
ATEX and markings, applied to the AEx-8XXP(H) Series Graphic Operator Interface,
are as follows:
AEx-8XXP(H) Series
II 3G Ex nA ic IIC T4 Gc and CID2 IP66
Temperature < 135°C
Power Input Voltage: DC 9~36V
TUV 15 ATEX 7701 X
IECEx TUR 16.0008X
WARNING: Do not disconnect while circuit is live. Potential
electrostatic charges. Wipe the front panel of the terminal with a
damp cloth before turning on.
AEx-8XXP(H) Series User Manual
4
Table of Contents
Revision History…………………………………………………………………………………………………….1
Warning!/Caution………………..……………...................................…………………………….…2
Packing List…………………………………….……………………………………………………………………..3
Safety Precautions…………………………………………………………………….…..……………………..4
Chapter 1
Getting Started
1.1 Features………………………..………………………...…………………………..7
1.2 Specifications…………………...………………………………………………….7
1.3 Dimensions………………………....…………………………………………..….9
1.4 Brief Description of AEx-8XXP(H)………………………….……….……11
1.5 VESA Mounting…………………………………………………………………12
1.6 Panel Mounting…………………………………………………………………12
Chapter 2
Hardware
2.1 Motherboard Introduction……………………...……………..………....13
2.2 Specifications…………………………..…………………………………………13
2.3 Jumpers and Connectors Location……………………………………...17
2.4 Jumpers Setting and Connectors…………………………………..……18
Chapter 3
BIOS Setup
3.1 Operations after POST Screen…...…….……...…………………………33
3.2 BIOS Setup Utility……………………………………………………………….33
3.3 Main Settings……………………………………..………………………………34
3.4 Advanced Settings……………………………………………………………...35
3.5 Chipset Settings……………………………………….………………………...43
3.6 Security Settings…………………………………………….…………………..45
3.7 Boot Settings…..………………………………………….……………………..46
3.8 Save & Exit Settings……………………………………..…………………....47
Chapter 4
Installation of Drivers
4.1 Intel (R) AtomTM SoC Chipset ………..……...………….………………50
4.2 Intel (R) VGA Chipset……………………………………………….……......53
4.3 Realtek ALC662 HD Audio Driver Installation…….……..………...57
4.4 Com Driver……………………………………………………..…………………59
4.5 Intel_TXE(Win) Driver……….……………………………………………….61
AEx-8XXP(H) Series User Manual
5
Chapter 5
Touch Screen Installation
5.1 Windows 8.1/10 Universal Driver Installation……..………………64
5.2 Software Function…………….…………………………………….……......68
Figures
Figure 1.1: Dimensions of AEx-815P(H)……..…………………..……………….....9
Figure 1.2: Dimensions of AEx-816P…………..…………………..……………….....9
Figure 1.3: Dimensions of AEx-819P(H)……..…………………..………………....10
Figure 1.4: Dimensions of AEx-821P…………..…………………..………………....10
Figure 1.5: Front View of AEx-8XXP(H).…………………………………….…….….11
Figure 1.6: Rear View of AEx-8XXP(H)……..…………………………………….….11
Figure 1.7: AEx-8XXP(H) Series VESA Mounting..…………………….…….….12
Figure 1.8: AEx-8XXP(H) Series Panel Mounting…………………………….….12
Figure 2.1: Motherboard Dimensions………………………………………….…….16
Figure 2.2: Jumpers and Connectors Location-Board Top……………….….17
Figure 2.3: Jumpers and Connectors Location-Board Bottom…………..…17
AEx-8XXP(H) Series User Manual
6
Chapter 1
Getting Started
1.1 Features

Intel® Celeron Processor N2930

Full flat bezel and fanless design

Full IP66 grade with M12 waterproof connector

DC 9~36V wide range power input

Projective capacitive touch

316 Stainless steel design
1.2 Specifications
AEx-815P(H)
AEx-816P
AEx-819P(H)
AEx-821P
System
CPU
Onboard Intel Celeron N2930 1.83GHz Processor
Chipset
SoC
Memory
Onboard 8GB DDR3L
IO Port
USB
1 x M12 for 2 x USB2.0 with metal waterproof CAP
Serial/Parallel
1 x M12 for COM1— RS-232(RS-422/485 for option) with metal waterproof CAP
LAN
2 x M12 for LAN with metal waterproof CAP
Power
1 x M12 for DC power input with metal waterproof CAP
VGA
1 x M12 for VGA with metal waterproof CAP
Optional IO Port (Must be a replacement for standard I/O)
USB
1 x M12 for 2 x USB2.0 (Cannot support 2 x M12 for 2 x USB2.0)
1 x M12 for 1 x USB3.0
Serial/Parallel
1 x M12 for 1x RS-232 (Cannot support 2 x M12 for 2x RS-232)
Storage Space
Storage
1 x 2.5” SATA HDD or SSD space
1 x Internal SD Card slot on board
1 x mSATA slot
Display
Display type
15” color TFT LCD
15.6” color TFT LCD
19” color TFT LCD
21.5” color TFT LCD
Max. Resolution
1024 x 768
1920 x 1080
1280 x 1024
1920 x 1080
Max. Color
16.2M
16.7M
16.7M
16.7M
2
Luminance (cd/m )
450
1000
AEx-8XXP(H) Series User Manual
400
350
1000
300
7
Contrast Ratio
800: 1
700: 1
1000: 1
5000: 1
Viewing Angle
160(H) / 150(V)
160(H) / 140(V)
170(H) / 160(V)
178(H) / 178(V)
Backlight Lifetime
50,000 hrs
50,000 hrs
50,000 hrs
50,000 hrs
MAX: 33.3W
MAX: 38.8W
Power
Power Input
DC 9~36V
Power Consumption
MAX: 22.2W
MAX: 24.7W
Mechanical
Construction
316 Stainless Steel Chassis
Mounting
VESA Mount 100 x100 (default)
Panel Mount (option)
Dimension (mm)
399 x 324 x 70mm
440 x 290 x 75mm
470 x 388.6 x 75mm
571 x 362 x 75.1mm
Net Weight (Kg)
9.4
10.1
13
13.3
Environmental
Operating
temperature
-20~60°C
Storage temperature
-30~70°C
Altitude limit for
application
Under 2000m
Overvoltage
category
CAT II
Pollution degree
2
Storage humidity
10 to 90% @ 40°C, non- condensing
Certification
CE / FCC Class A
Operating System Support
OS Support
AEx-8XXP(H) Series User Manual
Windows 7 Embedded Standard
Windows Embedded Standard 7
Windows Embedded 8.1 Pro
Windows Embedded 8.1 Industry Pro
Windows 10 IOT Enterprise LTSB 2016
8
1.3 Dimensions
Figure 1.1: Dimensions of AEx-815P(H)
Figure 1.2: Dimensions of AEx-816P
AEx-8XXP(H) Series User Manual
9
Figure 1.3: Dimensions of AEx-819P(H)
Figure 1.4: Dimensions of AEx-821P
AEx-8XXP(H) Series User Manual
10
1.4 Brief Description of AEx-8XXP(H) Series
AEx-8XXP(H) are panel PC series models for ATEX certification, which comes
with full waterproof with IP66 level designed. It is powered by Intel Celeron N2930
processor and supports 8GB DDR3L onboard memory. It comes with a 15”, 15.6”, 19”,
and 21.5” color TFT display. This model are designed by full waterproof connector
with 1x USB2.0 (support 2x USB2.0 function), 2x LAN, 1x COM and 1x VGA for
standard I/O port, but also can be replaced by USB2.0/3.0 or RS-232. The model
supports wide range DC 9~36V power input and can be panel mounted and VESA
mounted. AEx-8XXP(H) series has more outstanding features, thus you can use it in
some difficult environment and give the best in monitoring and control applications.
Figure 1.5: Front View of AEx-8XXP (H) Series
Figure 1.6: Rear View of AEx-8XXP (H) Series
AEx-8XXP(H) Series User Manual
11
1.5 VESA Mounting
The AEx-8XXP(H) series is designed to be VESA mounted as shown in Picture. Just
carefully place the unit through the hole and tighten the given screws from the rear
to secure the mounting.
Figure 1.7: AEx-8XXP (H) Series VESA Mounting
1.6 Panel Mounting
There are six holes located along the four sides of the panel PC. Insert the clamp
from the four sides and tighten them with the nuts provided.
Figure 1.8: AEx-8XXP (H) Series Panel Mounting
AEx-8XXP(H) Series User Manual
12
Chapter 2
Hardware
2.1 Motherboard Introduction
SBC-7111 is a 4" industrial motherboard developed on the basis of Intel Bay trail-I/M
Processors, which provides abundant peripheral interfaces to meet the needs of
different customers. Also, it features dual GbE ports, 4-COM ports and one Mini PCIE
configuration, one VGA port, one HDMI port, one LVDS interface. To satisfy the
special needs of high-end customers, CN1 and CN2 and CN3 richer extension
functions. The product is widely used in various sectors of industrial control.
2.2 Specifications
Specifications
Board Size
170mm x 113mm
CPU Support
Intel Atom E3845 / 1.91GHz (4cores, 10W, onboard)
Intel Celeron N2930 / 1.83 up to 2.16GHz (4cores, option)
Chipset
SoC
Memory Support
Onboard 2GB DDR3L SDRAM (N2930, option)
Onboard 4GB DDR3L SDRAM (E3845/N2930, option)
Onboard 8GB DDR3L SDRAM (N2930, option)
Graphics
Intel® HD Graphics 313/854MHz (N2930)
Intel® HD Graphics 542/792MHz (E3845)
Display Mode
1 x HDMI Port
1 x LVDS (18/24-bit dual LVDS)
1 x CRT Port
Support
Up to 1920 x 1200 for HDMI
Resolution
Up to 1920 x 1200 for LVDS (PS8625)
Up to 1920 x 1200 for CRT
Dual Display
HDMI + LVDS
HDMI + CRT
LVDS + CRT
Super I/O
ITE IT8518E
Fintek F81216AD
AEx-8XXP(H) Series User Manual
13
BIOS
AMI/UEFI
Storage
1 x SATAII Connector (7Pin, option)
1 x SATAII Connector (7Pin + 15Pin)
1 x SD Slot (USB2 to SD)
Ethernet
2 x PCIe Gbe LAN by Intel 82574L
USB 3.0 Hub(USB5534):
2 x USB 3.0/USB 2.0 (type A)stack ports (E2_USB5/E2_USB6)
1 x USB 2.0 for Touch controller (E2_USB7)
USB
1 x USB 2.0 Pin header for CN1 (E2_USB8)
USB 2.0 Hub(USB2514)
1 x USB 2.0 Pin header for CN2 (E-USB9)
2 x USB 2.0 Pin header for CN3 (E-USB10/E-USB11)
1 x USB 2.0 for MPCIE1 (E-USB12)
1 x RS232/RS422/RS485 port, DB9 connector for external (COM1) Pin 9
w/5V/12V/Ring select
Serial
1 x RS232 port, DB9 connector for external (COM2) Pin 9
w/5V/12V/Ring select
2 x UART for CN3 (COM3,COM4)
2 x RS422/485 header for CN2 (IT8518E/COM5/COM6)
Digital I/O
8-bit digital I/O by Pin header (CN2)
4-bit digital Input
4-bit digital Output
4-bit digital I/O by Pin header (CN3)
2-bit digital Input
2-bit digital Output
Battery
Support CR2477 Li battery by 2-pin header (BAT1/CMOS)
Audio
Support Audio via Realtek ALC662-VD HD audio codec
Support Line-in, Line-out, MIC by 2x6-pin header
Keyboard /Mouse
1 x PS2 keyboard/mouse by box pin header (CN3)
Expansion Bus
1 x mini-PCI-express slot
1 x PCI-express (CN3)
Touch Ctrl
1 x Touch ctrl header for TCH1 (PM6000 for USB4 or COM6)
Power Management
Wide Range DC6V~36V input
1 x 3-pin power input connector (DC_IN1/DC6~36V)
AEx-8XXP(H) Series User Manual
14
1 x 4-pin power input connector (DC_IN2/DC12V)
Switches and LED
1 x Power on/off switch (BT1/BT2/P_SW/CN2/CN3)
Indicators
1 x Reset (CN2)
1 x Power LED status (CN1)
1 x HDD LED status (CN2)
1 x Buzzer
External I/O port
2 x COM Ports (COM1/COM2)
2 x USB 3.0/2.0 Ports (stack)
2 x RJ45 GbE LAN Ports
1 x HDMI Port
1 x Stack audio Jack (Line out)
1 x Power on/off switch (BT1)
Temperature
Humidity
Operating: -20°C to 70°C
Storage: -40°C to 85°C
10% - 90%, non-condensing, operating
12V /0.80A (Intel Atom E3845 processor with 4GB DDR3L DRAM)
Power Consumption
12V /0.60A (Intel Atom E3815 processor with 2GB DDR3L DRAM)
12V /0.70A (Intel Celeron N2930 processor with 4GB DDR3L DRAM)
EMI/EMS
Meet CE/FCC class A
AEx-8XXP(H) Series User Manual
15
(units :mm)
Figure 2.1: Motherboard Dimensions
AEx-8XXP(H) Series User Manual
16
2.3 Jumpers and Connectors Location
Figure 2.2: Jumpers and Connectors Location- Board Top
Figure 2.3: Jumpers and Connectors Location- Board Bottom
AEx-8XXP(H) Series User Manual
17
2.4 Jumpers Setting and Connectors
1.
U2:
(FCBGA1170), onboard Intel Bay trail-I/M Processors.
Model
Processor
Number
PBF
Cores/Threads
TDP
N2930
1.83 up to
2.16GHz
4/4
4.5/7.5W
E3845
1.91GHz
4/4
10W
Remarks
SBC-7111-N2930-4G
SBC-7111-N2930-4G-SW
SBC-7111-N2930P-4G
SBC-7111-N2930-2G
SBC-7111-N2930P-CN3V-2G
SBC-7111-N2930-8G
SBC-7111-E3845-4G
2.
H3/H4/H5/H6 (option):
U2 Heat Sink Screw holes, four screw holes for Intel Bay trail-I/M Processors
Heat Sink assemble.
3.
U3/U4/U5/U6:
(FBGA96), Onboard DDR3L Memory.
4.
5.
Model
Memory
SBC-7111-N2930-4G
4GB
SBC-7111-N2930-4G-SW
4GB (option)
SBC-7111-N2930P-4G
4GB (option)
SBC-7111-E3845-4G
4GB (option)
SBC-7111-N2930-2G
2GB (option)
SBC-7111-N2930P-CN3V-2G
2GB (option)
SBC-7111-N2930-8G
8GB (option)
option
S-422 (PIN6):
(Switch), ATX Power and Auto Power on jumper setting.
S-422(Switch)
Mode
Pin6 (Off)
Manual Power on
Pin6 (On)
Auto Power on (Default)
BAT1:
(1.25mm Pitch 1x2 Wafer Pin Header) 3.0V Li battery is embedded to provide
power for CMOS.
AEx-8XXP(H) Series User Manual
18
6.
Pin#
Signal Name
1
VBAT
2
Ground
DC_IN1:
(5.08mm Pitch 1x3 Pin Connector), DC9~36V System power input connector.
Pin#
7.
PIN OUT
CN. 1
Wire Color
Power Input
CN. 2
1
Yellow
DC+6V~36V
Tail peeling 60mm
2
Black
Ground
Tail peeling 60mm
3
Green
FG
Tail peeling 60mm
Model
DC_IN1
SBC-7111-N2930-4G
180°Connector
SBC-7111-N2930-4G-SW
180°Connector
SBC-7111-N2930-2G
180°Connector
SBC-7111-N2930-8G
180°Connector
SBC-7111-E3845-4G
180°Connector
SBC-7111-N2930P-4G
45°Connector
SBC-7111-N2930P-CN3V-2G
45°Connector
DC_IN2 (option):
(2.0mm Pitch 1x4 wafer Pin Header) DC12V System power input connector.
Pin#
Signal Name
1
VCC_BAT (DC+12V input)
2
VCC_BAT (DC+12V input)
3
Ground
4
Ground
AEx-8XXP(H) Series User Manual
19
8.
BT1/BT2/P_SW (option):
Power on/off button, it is used to connect power switch button. The two pins
are disconnected under normal condition. You may short them temporarily to
realize system startup & shutdown or awaken the system from sleep state.
9.
Model
BT1
BT2
P_SW1
SBC-7111-N2930-4G
●
●
○
SBC-7111-N2930P-4G
●
●
○
SBC-7111-N2930-2G
●
●
○
SBC-7111-N2930-8G
●
●
○
SBC-7111-E3845-4G
●
●
○
SBC-7111-N2930P-CN3V-2G
○
●
○
SBC-7111-N2930-4G-SW
○
●
●
FAN1(option):
(2.54mm Pitch 1x3 Pin Header), Fan connector, cooling fans can be connected
directly for use. You may set the rotation condition of cooling fan in menu of
BIOS CMOS Setup.
Pin#
Signal Name
1
Ground
2
VCC
3
Rotation detection
Note:
Output power of cooling fan must be limited under 5W.
Model
10.
FAN1
SBC-7111-N2930-4G
○
SBC-7111-N2930-4G-SW
○
SBC-7111-N2930P-4G
○
SBC-7111-N2930P-CN3V-2G
○
SBC-7111-E3845-4G
○
SBC-7111-N2930-2G
○
SBC-7111-N2930-8G
○
VGA1:
AEx-8XXP(H) Series User Manual
20
(CRT 2.0mm Pitch 2x6 Pin Header), Video Graphic Array Port, Provide 2x6Pin
cable to VGA Port.
Signal Name
Pin#
Pin#
Signal Name
CRT_RED
1
2
Ground
CRT_GREEN
3
4
Ground
CRT_BLUE
5
6
VGA_EN
CRT_H_SYNC
7
8
CRT_DDCDATA
CRT_V_SYNC
9
10
CRT_DDCCLK
Ground
11
12
Ground
○
VGA hot plug setting:
VGA1 (Pin Header)
Function
Pin4-Pin6 (Close)
VGA Simulation Disabled
Pin4-Pin6 (Open)
VGA Simulation Enabled
Use the 2.0mm jumper cap to close pin4 and pin6
11.
HDMI1:
(HDMI 19P Connector), High Definition Multimedia Interface connector.
12.
JP6:
(2.0mm Pitch 2x2 Pin Header), LVDS jumper setting.
13.
JP6
Function (CN1)
Pin1-Pin2 (Close)
Single channel LVDS
Pin1-Pin2 (Open)
Dual channel LVDS (Default)
Pin3-Pin4 (Close)
8/24 bit (Default)
Pin3-Pin4 (Open)
6/18 bit
U18:
AT24C02-DIP8,The EEPROM IC(U18)is the set of LVDS resolution. If you need
other resolution settings, please upgrade U18 data.
Model
LVDS resolution
SBC-7111-N2930-4G
SBC-7111-N2930-4G-SW
1280*1024 (Default)
AEx-8XXP(H) Series User Manual
800*480 (option)
21
14.
15.
SBC-7111-N2930P-4G
800*600 (option)
SBC-7111-N2930P-CN3V-2G
SBC-7111-N2930-2G
SBC-7111-N2930-8G
SBC-7111-E3845-4G
1024*768 (option)
1920*1080 (option)
------
INVT1:
(2.0mm Pitch 1x6 wafer Pin Header), Backlight control connector for LVDS.
Pin#
Signal Name
1
+DC12V
2
+DC12V
3
Ground
4
Ground
5
BKLT_EN_OUT
6
BKLT_CTRL
CN1:
(1.25mm Pitch 2x20 Connector, DF13-40P), for 18/24-bit LVDS output connector,
fully supported by Parad PS8625(DP to LVDS), the interface features dual
channel 24-bit output. Low Voltage Differential Signaling, A high speed, low
power data transmission standard used for display connections to LCD panels.
Function
LVDS
Signal Name
Pin#
Pin#
Signal Name
12V_S0
2
1
12V_S0
BKLT_EN_OUT
4
3
BKLT_CTRL
Ground
6
5
Ground
LVDS_VDD5
8
7
LVDS_VDD5
LVDS_VDD3
10
9
LVDS_VDD3
Ground
12
11
Ground
LA_D0_P
14
13
LA_D0_N
LA_D1_P
16
15
LA_D1_N
LA_D2_P
18
17
LA_D2_N
LA_D3_P
20
19
LA_D3_N
LA_CLKP
22
21
LA_CLKN
LB_D0_P
24
23
LB_D0_N
AEx-8XXP(H) Series User Manual
Function
LVDS
22
D2-USB8
Power LED
16.
17.
18.
LB_D1_P
26
25
LB_D1_N
LB_D2_P
28
27
LB_D2_N
LB_D3_P
30
29
LB_D3_N
LB_CLKP
32
31
LB_CLKN
Ground
34
33
Ground
E2-USB8_P
36
35
E2-USB8_N
5V_S5_USB
38
37
5V_S5_USB
PWR_LED+
40
39
Ground
E2-USB8
Power LED
JP4 (Reserve):
(2.0mm Pitch 2x2 Pin Header).
JP4
Function
Close 3-4 (default)
-
Open 1-2 (default)
-
Close 3-4 (option)
Hardware Enabled
TCH1:
(2.0mm Pitch 1x6 wafer Pin Header), internal Touch controller connector.
Pin#
Signal Name
1
SENSE
2
X+
3
X-
4
Y+
5
Y-
6
GND_EARCH
Touch Interface Setting
EC(U44) Data
TCH1(PM6000)
Option A
CN1(E2-USB8)
Option B
JP1:
(2.0mm Pitch 2x3 Pin Header), COM1 jumper setting, pin 1~6 are used to select
signal out of pin 9 of COM1 port.
JP1 Pin#
AEx-8XXP(H) Series User Manual
Function
23
19.
Close 1-2
COM1 RI (Ring Indicator) (default)
Close 3-4
COM1 Pin9: DC+5V
(option)
Close 5-6
COM1 Pin9: DC+12V
(option)
S_232:
(Switch), COM1 jumper setting, it provides selectable RS232 or RS422 or RS485
serial signal output.
Function
20.
S_232 Pin# (switch)
RS232 (Default)
ON: Pin1, Pin2, Pin3, Pin4, Pin5
RS422 (option)
OFF: Pin1, Pin2, Pin3, Pin4, Pin5
RS485 (option)
OFF: Pin1, Pin2, Pin3, Pin4, Pin5
S_422:
(Switch), COM1 setting, it provides selectable RS232 or RS422 or RS485 serial
signal output.
Function
21.
S_422 Pin# (switch)
RS232 (Default)
OFF: Pin1, Pin2, Pin3, Pin4, Pin5
RS422 (option)
ON: Pin1, Pin2, Pin3, Pin4, Pin5
RS485 (option)
ON: Pin1, Pin2, Pin3, Pin4, Pin5
S-422 (switch)
Mode
Pin6 (Off)
ATX Power
Pin6 (On)
Auto Power on (Default)
COM1:
(Type DB9M), Rear serial port, standard DB9 Male serial port is provided to
make a direct connection to serial devices. COM1 port is controlled by pins
No.1~6 of JP1, select output Signal RI or 5V or 12V, for details, please refer to
description of JP1 and S_232 and S_422 setting.
RS232 (Default)
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
AEx-8XXP(H) Series User Manual
24
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
JP1 select Setting (RI/5V/12V)
BIOS Setup:
Advanced/F81216SEC Super IO Configuration/Serial Port 1 Configuration 【RS-232】
RS422 (option)
Pin#
Signal Name
1
422_RX+
2
422_RX-
3
422_TX-
4
422_TX+
5
Ground
6
NC
7
NC
8
NC
9
NC
BIOS Setup:
Advanced/F81216SEC Super IO Configuration/Serial Port 1 Configuration 【RS-422】
RS485 (option)
Pin#
Signal Name
1
NC
2
NC
3
485-
4
485+
5
Ground
6
NC
7
NC
8
NC
9
NC
BIOS Setup:
Advanced/F81216SEC Super IO Configuration/Serial Port 1 Configuration 【RS-485】
22.
JP2:
AEx-8XXP(H) Series User Manual
25
(2.0mm Pitch 2x3 Pin Header), COM2 jumper setting, pin 1~6 are used to select
signal out of pin 9 of COM2 port.
23.
JP2 Pin#
Function
Close 1-2
COM2 RI (Ring Indicator) (default)
Close 3-4
COM2 Pin9: DC+5V
(option)
Close 5-6
COM2 Pin9: DC+12V
(option)
COM2:
(Type DB9M),Rear serial port, standard DB9 Male serial port is provided to
make a direct connection to serial devices.
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
JP2 select Setting (RI/5V/12V)
24.
LED1, LED2, LED3, LED4 (option) :
LED1: LED STATUS. Green LED for Motherboard Power Good status.
LED2: LED STATUS. Green LED for Touch Power Status.
LED3: LED STATUS. Green LED for EC Power status.
LED4: LED STATUS. Green LED for Motherboard Power Good status.
25.
SATA_P (option):
(2.5mm Pitch 1x2 box Pin Header), One onboard 5V output connector is
reserved to provide power for SATA devices.
AEx-8XXP(H) Series User Manual
Pin#
Signal Name
1
+DC5V
2
Ground
26
Note:
Output current of the connector must not be above 1A.
Model
26.
SATA_P (Wafer)
SBC-7111-N2930-4G
○
SBC-7111-N2930-4G-SW
○
SBC-7111-N2930P-4G
○
SBC-7111-N2930P-CN3V-2G
○
SBC-7111-E3845-4G
○
SBC-7111-N2930-2G
○
SBC-7111-N2930-8G
○
SATA2 (option):
(SATA 7Pin), SATA Connectors, one SATA connector is provided with transfer
speed up to 3.0Gb/s.
Model
SATA2 (Connectors)
SBC-7111-N2930-4G
○
SBC-7111-N2930-4G-SW
○
SBC-7111-N2930P-4G
○
SBC-7111-N2930P-CN3V-2G
○
SBC-7111-E3845-4G
○
SBC-7111-N2930-2G
○
SBC-7111-N2930-8G
○
27.
SATA1:
(SATA 7Pin+15Pin), SATA Connectors, one SATA connector is provided with
transfer speed up to 3.0Gb/s.
28.
SD1:
(SD card slot), Secure Digital Memory Card socket.
29.
MPCIE1:
(Socket 52Pin), mini PCIe socket, it is located at the top, it supports mini PCIe devices
with USB2.0 and LPC and SMBUS and PCIe signal. MPCIe card size is 30x50.95mm.
30.
H1/H2:
MPCIE1 SCREW HOLES, H1and H2 for mini PCIE card (30mmx50.95mm)
assemble.
AEx-8XXP(H) Series User Manual
27
31.
F_AUDIO1:
(2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662-VD
codec is used to provide high-quality audio I/O ports. Line Out can be
connected to a headphone or amplifier. Line In is used for the connection of
external audio source via a Line in cable. MIC is the port for microphone input
audio.
32.
33.
Signal Name
Pin#
Pin#
Signal Name
+5V
1
2
GND_AUD
LINE-OUT-L
3
4
LINE-OUT-R
FRONT_JD
5
6
LINE1_JD
LINE_IN-L
7
8
LINE-IN-R
MIC-IN-L
9
10
MIC-IN-R
GND-AUD
11
12
MIC1_JD
LINE_OUT1:
(Diameter 3.5mm Jack), HD Audio port, an onboard Realtek ALC662-VD codec
is used to provide high quality audio I/O ports. Line Out can be connected to a
headphone or amplifier.
Model
LINE_OUT1
SBC-7111-N2930-4G
●
SBC-7111-N2930P-4G
●
SBC-7111-N2930-2G
●
SBC-7111-N2930-8G
●
SBC-7111-E3845-4G
●
SBC-7111-N2930P-CN3V-2G
○
SBC-7111-N2930-4G-SW
●
USB3:
USB0/USB3: (Double stack USB type A), Rear USB connector, it provides up to
two USB3.0 ports, one USB2.0 port, supports USB full-speed and low-speed
signaling.
AEx-8XXP(H) Series User Manual
28
Each USB Type A Receptacle (2 Ports) Current limited value is 2.0A.
If the external USB device current exceeds 2.0A, please separate connectors
into different Receptacle.
34.
LAN1/LAN2:
LAN1/LAN2: (RJ45 Connector), Rear LAN port, Two standard 10/100/1000M
RJ-45 Ethernet ports are provided. Use Intel 82574L chipset, LINK LED (green)
and ACTIVE LED (yellow) respectively located at the left-hand and right-hand
side of the Ethernet port indicate the activity and transmission state of LAN.
Model
RJ45(LAN1)
RJ45(LAN2)
SBC-7111-N2930-4G
●
●
SBC-7111-N2930P-4G
●
●
SBC-7111-N2930-2G
●
●
SBC-7111-N2930-8G
●
●
SBC-7111-E3845-4G
●
●
SBC-7111-N2930P-CN3V-2G
●
○
SBC-7111-N2930-4G-SW
●
●
35.
BUZ1:
Onboard buzzer.
36.
CN2:
(DF13-30P Connector) For expand output connector, It provides eight GPIO,
one RS422 or RS485, one USB2.0, one Power on/off, one Reset.
Function
Signal Name
Pin#
Pin#
Signal Name
Function
5V
5V_S5
2
1
5V_S5
5V
SOC_GPIO10
GPIO_IN2
4
3
GPIO_IN1
SOC_SPIO09
SOC_GPIO26
GPIO_IN4
6
5
GPIO_IN3
SOC_GPIO17
SOC_GPIO05
GPIO_OUT2
8
7
GPIO_OUT1
SOC_GPIO04
SOC_GPIO08
GPIO_OUT4
10
9
GPIO_OUT3
SOC_GPIO06
Ground
12
11
Ground
AEx-8XXP(H) Series User Manual
29
485 or 422
485+_422TX5+
14
13
485-_422TX5-
485 or 422
RS422(COM5)
422_RX5+
16
15
422_RX5-
RS422(COM5)
485 or 422
485+_422TX6+
18
17
485-_422TX6-
485 or 422
RS422(COM6)
422_RX6+
20
19
422_RX6-
RS422(COM6)
5V
5V_S0
22
21
HDD_LED+
HDD LED
5V_USB09
24
23
5V_USB09
E_USB9_P
26
25
E_USB9_N
Ground
28
27
FP_RST-
PWRBTN_ON
30
29
Ground
USB2.0
Power auto on
USB2.0
RESET
COM5/COM6 BIOS Setup:
Advanced/IT8518Super IO Configuration/Serial Port 1 Configuration【RS-485】
Advanced/IT8518Super IO Configuration/Serial Port 1 Configuration【RS-422】
Advanced/IT8518Super IO Configuration/Serial Port 2 Configuration【RS-485】
Advanced/IT8518Super IO Configuration/Serial Port 2 Configuration【RS-422】
37.
38.
EC_GPIO1 (option):
(2.0mm Pitch 1X10 Pin Header)For expand connector, it provides eight GPIO.
Pin#
Signal Name
1
Ground
2
GPA0_ONOFF
3
GPA1_SPK-
4
GPE6_BKLT-
5
GPE0_BKLT+
6
SPKGPC3_SPK+
7
BKL_CTRL_PWR
8
ADC6_BKLT_CTRL
9
ADC7_L_SENSE
10
3.3V
Function
EC_GPIO1
Backlight Automatic dimming
○
Backlight manual dimming
○
CN3:
(1.27mm Pitch 2x30 Female Header), for expand output connector, it provides
four GPIO, two USB 2.0,one PS/2 mouse, one PS/2 keyboard, two UARTs, one
PCIex1, one SMbus connect to the TB-528 riser Card.
AEx-8XXP(H) Series User Manual
30
Function
Signal Name
Pin#
Pin#
Signal Name
5V_S5_USB
1
2
5V_S5_USB
5V_S5_USB
3
4
5V_S5_USB
USB1011_OC
5
6
PSON_ATX-
Exp-USB10
E-USB10_N
7
8
E-USB10_P
Exp-USB10
Exp-USB11
E-USB11_N
9
10
E-USB11_P
Exp-USB11
Ground
11
12
Ground
PS2_MSCLK
13
14
PS2_MSDATA
PS2_KBCLK
15
16
PS2_KBDATA
COM4_RI
17
18
COM4_DCD-
COM4
COM4_TXD
19
20
COM4_RXD
COM4
(UART)
COM4_DTR
21
22
RICOM4_RTS-
(UART)
COM4_DSR
23
24
COM_CTS-
Ground
25
26
Ground
COM3_RI
27
28
COM3_DCD-
COM3_TXD
29
30
COM3_RXD
COM3_DTR
31
32
DSRCOM3_RTS-
COM3_DSR
33
34
DTRCOM3_CTS-
GPIO23
SOC_GPIO23
35
36
ICH_GPIO22
GPIO22
GPIO25
SOC_GPIO25
37
38
ICH_GPIO24
GPIO24
Ground
39
40
Ground
PCIE_TX0_DN
41
42
PCIE_TX0_DP
PCIE_RX0_DN
43
44
PCIE_RX0_DP
Ground
45
46
Ground
PCIE_REFCLK0_DN
47
48
PCIE_REFCLK0_DP
PCIE0_WAKE_N
49
50
PLTRST_3P3_N
SMBUS
SMB_CLK_S0
51
52
SMB_DATA_S0
PCIE
PCIE_CLKREQ0_N
53
54
Ground
3P3V_S5
55
56
PWRBTN_ON-
3P3V_S5
57
58
3P3V_S5
12V_S0
59
60
12V_S0
Not Support
COM3
(UART)
PCIE 1X
12V
Function
Not Support
COM3
(UART)
PCIE 1X
SMBUS
Power Auto on
Model
CN3(connector)
SBC-7111-N2930-4G
90°Connector
SBC-7111-N2930-4G-SW
90°Connector
SBC-7111-N2930-2G
90°Connector
SBC-7111-N2930-8G
90°Connector
AEx-8XXP(H) Series User Manual
12V
31
SBC-7111-E3845-4G
90°Connector
SBC-7111-N2930P-4G
90°Connector
SBC-7111-N2930P-CN3V-2G
180°Connector
AEx-8XXP(H) Series User Manual
32
Chapter 3
BIOS Setup
3.1 Operations after POST Screen
After CMOS discharge or BIOS flashing operation, press [Delete] key to enter CMOS
Setup.
After optimizing and exiting CMOS Setup, the POST screen displayed for the first time
is as follows and includes basic information on BIOS, CPU, memory, and storage
devices.
3.2 BIOS Setup Utility
Press [Delete] key to enter BIOS Setup utility during POST, and then a main menu
containing system summary information will appear.
AEx-8XXP(H) Series User Manual
33
3.3 Main Settings
System Time:
Set the system time, the time format is:
AEx-8XXP(H) Series User Manual
Hour :
0 to 23
Minute :
0 to 59
34
Second : 0 to 59
System Date:
Set the system date, the date format is:
Day: Note that the ‘Day’ automatically changes when you set the date.
Month: 01 to 12
Date:
01 to 31
Year:
1998 to 2099
3.4 Advanced Settings
3.4.1 ACPI Settings
Enable ACPI Auto Conf:
[Disabled]
[Enabled]
Enable Hibernation:
AEx-8XXP(H) Series User Manual
35
[Enabled]
[Disabled]
ACPI Sleep State:
[S3 (Suspend to RAM) ]
[Suspend Disabled]
Lock Legacy Resources:
[Disabled]
[Enabled]
3.4.2 F81216SEC Super IO Configuration
Super IO chip F81216SEC
Serial Port 1 Configuration
UART1 Mode Selection:
[RS-232]
[RS-485]
[RS-422]
Serial Port 2 Configuration
Change Settings
[Auto]
Serial Port 3 Configuration
Change Settings
[Auto]
Serial Port 4 Configuration
Change Settings
[Auto]
3.4.3 IT8518 Super IO Configuration
Super IO chip IT8518/IT8519
Serial Port 1 Configuration
Backlight PWM Controller(COM5):
[RS-485]
[RS-422]
Serial Port 2 Configuration (COM6)
Change Settings
[Auto]
3.4.4 Intel® Smart Connect Technology
ISCT Support
[Disabled]
[Enabled]
AEx-8XXP(H) Series User Manual
36
3.4.5 Serial Port Console Redirection
COM0
Console Redirection
[Disabled]
[Enabled]
Console Redirection Settings
Legacy Console Redirection
Legacy Console Redirection settings
Serial Port for Out-of-Band Management/
Windows Emergency Management Services (EMS)
Console Redirection
[Disabled]
[Enabled]
Console Redirection Settings
3.4.6 CPU Configuration
Socket 0 CPU Information
Intel® Atom™ CPU E3845 @ 1.91GHz
CPU Signature
Microcode Patch
Max CPU Speed
30679
901
1910 MHz
Mix CPU Speed
Processor Cores
Intel HT Technology
Intel HT-X Technology
L1 Data Cache
L1 Code Cache
L2 Cache
L2 Cache
500 MHz
4
Not Supported
Supported
24KB x 4
32KB x 4
1024KB x 2
Not Present
CPU Thermal configuration
CPU Speed
64-bit
Hyper-Threading:
1918 MHz
Supported
[Enabled]
[Disabled]
AEx-8XXP(H) Series User Manual
37
Limit CPUID Maximum:
[Disabled]
[Enabled]
Execute Disable Bit:
[Enabled]
[Disabled]
Intel Virtualization Technology:
[Enabled]
[Disabled]
Power Technology
[Energy Efficient]
[Disabled]
[Custom]
3.4.7 PPM Configuration
CPU C State Report
[Enabled]
[Disabled]
Max CPU C-state
[C7]
[C6]
[C1]
SOix
[Disabled]
[Enabled]
3.4.8 Thermal Configuration Parameters
3.4.9 IDE Configuration
Serial-ATA(SATA)
[Enabled]
[Disabled]
SATA Test Mode
[Disabled]
[Enabled]
SATA Speed Support
[Gen2]
[Gen1]
AEx-8XXP(H) Series User Manual
38
SATA ODD Port
[No ODD]
[Porto ODD]
[Port1 ODD]
[Disabled]
SATA Mode
[AHCI Mode]
[IDE Mode]
Serial-ATA Port 0
[Enabled]
[Disabled]
SATA Port0 Hotplug
[Disabled]
[Enabled]
Serial-ATA Port 1
[Enabled]
[Disabled]
SATA Port1 Hotplug
[Disabled]
[Enabled]
SATA Port0
Not Present
SATA Port1
Not Present
3.4.10 Miscellaneous Configuration
AEx-8XXP(H) Series User Manual
39
High Precision Timer
[Enabled]
[Disabled]
Boot Timer with HPET Timer
[Disabled]
[Enabled]
PCI Express Dynamic Clock Gating
[Disabled]
[Enabled]
OS Selection
Use the OS Selection option to select an operating system for the system.
Note:
Users must go to this item to select the OS mode before installing corresponding
OS driver, otherwise problems will occur when installing the driver.
3.4.11 LPSS & SCC Configuration
LPSS & SCC Configuration
SCC Configuration
SCC eMMC Support
SCC eMMC 4.5 DDR50 Support
SCC eMMC 4.5 HS200 Support
eMMC Secure Erase
SCC SDIO Support
SCC SD Card Support
SDR25 Support for SDCard
SDR50 Support for SDCard
MIPI HSI Support
[ACPI Mode]
[eMMC AUTO MODE]
[Enabled]
[Disabled]
[Disabled]
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[Disabled]
LPSS Configuration
LPSS DMA #1 Support
LPSS DMA #2 Support
LPSS I2C #1 Support
LPSS I2C #2 Support
LPSS I2C #3 Support
LPSS I2C #4 Support
AEx-8XXP(H) Series User Manual
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
40
LPSS I2C #5 Support
[Enabled]
LPSS I2C #6 Support
LPSS I2C #7 Support
NFC
Touch Pad
I2C touch Device Address
LPSS HSUART #1 Support
LPSS HSUART #2 Support
LPSS PWM #1 Support
LPSS PWM #2 Support
LPSS SPI Support
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
3.4.12 System Component
3.4.13 Network Stack Configuration
Network Stack
3.4.14 CSM Configuration
CSM Support
CSM16 Module Version
GateA20 Active
Option ROM Messages
Boot option filter
[Disabled]
[Enabled]
07.76
[Upon Request]
[Always]
[Force BIOS]
[Keep Current]
[UEFI and Legacy]
[Legacy only]
[UEFI only]
Network
[UEFI]
[Do not launch]
[Legacy]
Storage
[UEFI]
[Do not launch]
[Legacy]
Video
[Legacy]
[UEFI]
AEx-8XXP(H) Series User Manual
41
[Do not launch]
Other PCI devices
[UEFI]
[Do not launch]
[Legacy]
3.4.15 SDIO Configuration
3.4.16 USB Configuration
USB Configuration
USB Module Version 8.11.02
USB Devices:
1 keyboard, 1 Mouse,2 Hubs
Legacy USB Support:
[Enabled]
[Disabled]
XHCI Hand-off:
[Enabled]
[Disabled]
EHCI Hand-off:
[Disabled]
[Enabled]
USB Mass Storage Driver Support
[Enabled]
[Disabled]
USB hardware delays and time-outs:
USB transfer time-out:
[20 sec]
[10 sec]
[5 sec]
[1 sec]
Device reset time-out:
[20 sec]
[10 sec]
[30 sec]
[40 sec]
Device power-up delay
[Auto]
[Manual]
AEx-8XXP(H) Series User Manual
42
3.4.17 Platform Trust Technology
3.4.18 Security Configuration
3.5 Chipset Settings
3.5.1 Host Bridge
►Intel IGD Configuration
►IGD – LCD Control
Force Lid Status
BIA
ALS Support
IGD Flat Panel
Pannel Scaling
[On]
[Off]
[Auto]
[Disabled]
[Auto]
[Auto]
►Memory Frequency and Timing
►Graphics Power Management Control
Memory Information
Total Memory
4096 MB(DDR3L)
Memory Slot0
4096 MB(DDR3L)
DIMM#1
Not Present
AEx-8XXP(H) Series User Manual
43
Max TOLUD
[Dynamic]
[2GB]
[2.25GB]
[2.5GB]
[2.75GB]
[3GB]
3.5.2 South Bridge
►Azalia HD Audio
►USB Configuration
USB OTG Support
USB VBUS
[Disabled]
[On]
XHCI Mode
USB2 Link Power Management
USB 2.0(EHCI) Support
USB EHCI debug
USB Per Port Control
USB Port 0
USB Port 1
USB Port 2
[Smart Auto]
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
USB Port 3
[Enabled]
AEx-8XXP(H) Series User Manual
44
3.6 Security Settings
3.6.1 Administrator Password
3.6.2 User Password
Type the password with up to 20 characters and then press Enter key. This will
clear all previously typed CMOS passwords. You will be requested to confirm the
password. Type the password again and press Enter key. You may press Esc
key to abandon password entry operation.
To clear the password, just press Enter key when password input window pops
up. A confirmation message will be shown on the screen as to whether the password
AEx-8XXP(H) Series User Manual
45
will be disabled. You will have direct access to BIOS setup without typing any
password after system reboot once the password is disabled.
Once the password feature is used, you will be requested to type the password each
time you enter BIOS setup. This will prevent unauthorized persons from changing
your system configurations.
Also, the feature is capable of requesting users to enter the password prior to
system boot to control unauthorized access to your computer. Users may enable the
feature in Security Option of Advanced BIOS Features. If Security Option is set to
System, you will be requested to enter the password before system boot and when
entering BIOS setup; if Security Option is set to Setup, you will be requested for
password for entering BIOS setup.
3.7 Boot Settings
Setup Prompt Timeout
Bootup Numlock State
[1]
[On]
[off]
Quiet Boot
[Disabled]
AEx-8XXP(H) Series User Manual
46
[Enabled]
Fast Boot
[Disabled]
[Enabled]
Boot Option Priorities
Boot Option #1
Hard Drive BBS Priorities
Sets the system boot order
[SATA PM:*** … ]
Boot Option #1
SATA PM:***…
******
Disabled
3.8 Save & Exit Settings
Save Changes and Exit
Save & Exit Setup save Configuration and exit ?
[Yes]
[No]
AEx-8XXP(H) Series User Manual
47
Discard Changes and Ext
Exit Without Saving Quit without saving?
[Yes]
[No]
Save Changes and Reset
Save & reset Save Configuration and reset?
[Yes]
[No]
Discard Changes and Reset
Reset Without Saving Reset without saving?
[Yes]
[No]
Save Changes
Save Setup Values Save configuration?
[Yes]
[No]
Discard Changes
Load Previous Values Load Previous Values?
[Yes]
[No]
Restore Defaults
Load Optimized Defaults Load optimized Defaults?
[Yes]
[No]
Save user Defaults
Save Values as User Defaults Save configuration?
[Yes]
[No]
Restore user Defaults
Restore User Defaults Restore User Defaults?
[Yes]
[No]
Launch EFI Shell from filesystem device
WARNING Not Found
[ok]
Reset System with ME disable ModeMEUD000
ME will runs into the temporary disable mode, Ignore if ME Ignition
FWMEUD001.
AEx-8XXP(H) Series User Manual
48
Chapter 4
Installation of Drivers
This chapter describes the installation procedures for software and drivers under the
windows 8.1 & 10. The software and drivers are included with the motherboard.
The contents include Intel/VGA chipset driver, Audio driver, Com Driver, and
TXE(Win) Driver Installation instructions are given below.
Important Note:
After installing your Windows operating system, you must install first the Intel
Chipset Software Installation Utility before proceeding with the installation of
drivers.
AEx-8XXP(H) Series User Manual
49
4.1 Intel® AtomTM SoC Chipset
To install the Intel chipset driver, please follow the steps below.
Step 1. Select Intel ® AtomTM SoC Chipset from the list
Step 2. Here is welcome page. Please make sure you save and exit all programs
before install. Click Next.
AEx-8XXP(H) Series User Manual
50
Step 3. Read the license agreement. Click Accept to accept all of the terms of the
license agreement.
Step 4. Click Install to begin the installation.
AEx-8XXP(H) Series User Manual
51
Step 5. Click Finish to exit the wizard.
AEx-8XXP(H) Series User Manual
52
4.2 Intel® VGA Chipset
To install the Intel® VGA Chipset, please follow the steps below.
Step 1. Select Intel® VGA Chipset from the list.
Step 2. . Click Next.
AEx-8XXP(H) Series User Manual
53
Step 3. Choose automatically run function and Click Next to setup program.
Step 4. Read the license agreement. Click Yes to accept all of the terms of the license
agreement.
AEx-8XXP(H) Series User Manual
54
Step 5. Click Next to continue.
Step 6. Click Next to continue.
AEx-8XXP(H) Series User Manual
55
Step 7. Select Yes, I want to restart this computer now. Click Finish, then remove
any installation media from the drives.
AEx-8XXP(H) Series User Manual
56
4.3 Realtek ALC662 HD Audio Driver Installation
To install the Realtek ALC662 HD Audio Driver, please follow the steps below.
Step 1. Select Realtek AL662 HD Audio Driver from the list
Step 2. Click Next to continue.
AEx-8XXP(H) Series User Manual
57
Step 3. Click Yes, I want to restart my computer now. Click Finish to complete the
installation.
AEx-8XXP(H) Series User Manual
58
4.4 Com Driver
To install the Com Driver, please follow the steps below.
Step 1. Select Com Driver from the list
Step 2. Select setup language you need. Click Next to continue.
AEx-8XXP(H) Series User Manual
59
Step 3. Click Next to begin the installation.
Step 4. Choose Yes, I want to restart my computer now. Click Finish to complete the
installation.
AEx-8XXP(H) Series User Manual
60
4.5 Intel_TXE(Win) Driver
To install the Intel_TXE(Win) Driver, please follow the steps below.
Step 1. Select Intel_TXE(Win) Driver from the list
Step 2. Click Next to continue.
AEx-8XXP(H) Series User Manual
61
Step 3. Read the license agreement. Choose Accept and click Next to accept all of the
terms of the license agreement.
Step 4. Click Next to continue.
AEx-8XXP(H) Series User Manual
62
Step 5. Click Finish to complete the installation.
AEx-8XXP(H) Series User Manual
63
Chapter 5
Touch Screen Installation
This chapter describes how to install drivers and other software that will allow your
touch screen work with different operating systems.
5.1 Windows 8.1/10 Universal Driver Installation for
PenMount 6000 Series
Before installing the Windows 8.1/10 driver software, you must have the Windows
8.1/10 system installed and running on your computer. You must also have one of
the following PenMount 6000 series controller or control boards installed: PM6500,
PM6300.
5.1.1 Installing Software
If you have an older version of the PenMount Windows 7 driver installed in your
system, please remove it first. Follow the steps below to install the PenMount
DMC6000 Windows 8.1/10 driver.
Step 1. Insert the product CD, the screen below would appear. Click Touch Panel
Driver.
AEx-8XXP(H) Series User Manual
64
Step 2. Click Next to continue.
Step 3. Read the license agreement. Click I Agree to agree the license agreement.
AEx-8XXP(H) Series User Manual
65
Step 4. Choose the folder in which to install PenMount Windows Universal Driver.
Click Install to start the installation.
Step 5. Wait for installation. Then click Yes to continue.
AEx-8XXP(H) Series User Manual
66
Step 6. Click Finish to complete the installation.
AEx-8XXP(H) Series User Manual
67
5.2 Software Functions
Upon rebooting, the computer automatically finds the new 6000 controller board.
The touch screen is connected but not calibrated. Follow the procedures below to
carry out calibration.
1. After installation, click the PenMount Monitor icon “PM” in the menu bar.
2. When the PenMount Control Panel appears, select a device to “Calibrate.”
PenMount Control Panel
The functions of the PenMount Control Panel are Device, Multiple Monitor, Tools
and About, which are explained in the following sections.
Device
In this window, you can find out that how many devices be detected on your system.
AEx-8XXP(H) Series User Manual
68
Calibrate
This function offers two ways to calibrate your touch screen. ‘Standard Calibration’
adjusts most touch screens. ‘Advanced Calibration’ adjusts aging touch screens.
Standard Calibration
Click this button and arrows appear pointing to red
squares. Use your finger or stylus to touch the red
squares in sequence. After the fifth red point calibration
is complete. To skip, press ‘ESC’.
Advanced Calibration
Advanced Calibration uses 4, 9, 16 or 25 points to
effectively calibrate touch panel linearity of aged touch
screens. Click this button and touch the red squares in
sequence with a stylus. To skip, press ESC’.
Step 1. Please select a device then click “Configure”. You can also double click the
device too.
AEx-8XXP(H) Series User Manual
69
Step 2.Click “Standard Calibration” to start calibration procedure
NOTE: The older the touch screen, the more Advanced Mode calibration points
you need for an accurate calibration. Use a stylus during Advanced Calibration for
greater accuracy. Please follow the step as below:
AEx-8XXP(H) Series User Manual
70
Step 3. Select Device to calibrate, then you can start to do Advanced Calibration.
NOTE: Recommend to use a stylus during Advanced Calibration for greater
accuracy.
Plot Calibration Data
Check this function and a touch panel linearity
comparison graph appears when you have finished
Advanced Calibration. The blue lines show linearity
before calibration and black lines show linearity after
calibration.
Turn off EEPROM
storage
The function disable for calibration data to write in
Controller. The default setting is Enable.
AEx-8XXP(H) Series User Manual
71
Setting
Touch Mode
This mode enables and disables the mouse’s ability to drag
on-screen icons – useful for configuring POS terminals.
Mouse Emulation – Select this mode and the mouse
functions as normal and allows dragging of icons.
Click on Touch – Select this mode and mouse only provides a
click function, and dragging is disables.
Beep Sound
Enable Beep Sound – turns beep function on and off
Beep on Pen Down – beep occurs when pen comes down
Beep on Pen Up – beep occurs when pen is lifted up
Beep on both – beep occurs when comes down and lifted up
Beep Frequency – modifies sound frequency
Beep Duration – modifies sound duration
Cursor Stabilizer
Enable the function support to prevent cursor shake.
Use press and
hold as right click
You can set the time out and area for you need.
AEx-8XXP(H) Series User Manual
72
Edge Compensation
You can use Edge Compensation to calibrate more subtly.
About
This panel displays information about the PenMount controller and driver version.
AEx-8XXP(H) Series User Manual
73
Multiple Monitors
Multiple Monitors support from two to six touch screen displays for one system. The
PenMount drivers for Windows 8.1/10 support Multiple Monitors. This function
supports from two to six touch screen displays for one system. Each monitor
requires its own PenMount touch screen control board, either installed inside the
display or in a central unit. The PenMount control boards must be connected to the
computer COM ports via the USB interface. Driver installation procedures are the
same as for a single monitor. Multiple Monitors support the following modes:
Windows Extends Monitor Function
Matrox DualHead Multi-Screen Function
nVidia nView Function
NOTE: The Multiple Monitor function is for use with multiple displays only. Do not
use this function if you have only one touch screen display. Please note once
you turn on this function the rotating function is disabled.
Enable the multiple display function as follows:
1. Check the Enable Multiple Monitor Support box; then click Map Touch Screens
to assign touch controllers to displays.
2. When the mapping screen message appears, click OK.
3. Touch each screen as it displays “Please touch this monitor”. Following this
sequence and touching each screen is called mapping the touch screens.
AEx-8XXP(H) Series User Manual
74
4. Touching all screens completes the mapping and the desktop reappears on the
monitors.
5. Select a display and execute the “Calibration” function. A message to start
calibration appears. Click OK.
6. “Touch this screen to start its calibration” appears on one of the screens. Touch
the screen.
7. “Touch the red square” messages appear. Touch the red squares in sequence.
8. Continue calibration for each monitor by clicking Standard Calibration and
touching the red squares.
NOTES:
1. If you use a single VGA output for multiple monitors, please do not use the
Multiple Monitor function. Just follow the regular procedure for calibration on
each of your desktop monitors.
2. The Rotating function is disabled if you use the Multiple Monitor function.
3. If you change the resolution of display or screen address, you have to redo Map
Touch Screens, so the system understands where the displays are.
AEx-8XXP(H) Series User Manual
75
About
This panel displays information about the PenMount controller and this driver
version.
PenMount Monitor Menu Icon
The PenMount monitor icon (PM) appears in the menu bar of Windows 8.1/10
system when you turn on PenMount Monitor in PenMount Utilities.
PenMount Monitor has the following function
Control Panel
Open Control Panel Windows
Beep
Setting Beep function for each device
Right Button
When you select this function, a mouse icon appears in
the right-bottom of the screen.
Click this icon to switch between Right and Left Button
functions.
Exit
Exits the PenMount Monitor function.
AEx-8XXP(H) Series User Manual
76
Configuring the Rotate Function
1. Install the rotation software package.
2. Choose the rotate function (0°, 90°, 180°, 270°) in the 3rd party software. The
calibration screen appears automatically. Touch this point and rotation is
mapped.
NOTE: The Rotate function is disabled if you use Monitor Mapping.
AEx-8XXP(H) Series User Manual
77

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement