Bodycraft SPT V1 Indoor Cycle Owner's Manual

Bodycraft SPT V1 Indoor Cycle Owner's Manual
SPT INDOOR TRAINING CYCLE
ASSEMBLY MANUAL
MODEL: SPT
Questions?
As a quality exercise equipment supplier we are committed to your complete satisfaction. If you have
questions, or find missing or damaged parts, we will guarantee your complete satisfaction through our
authorized dealer service centers or our home office customer service department. Please call your local
dealer for assistance or BODYCRAFT at 800-990-5556 (9:00 AM - 5:00 PM). Our trained technicians will
provide immediate assistance to you, free of charge.
Bodycraft is a division of Recreation Supply Inc.
P. O. Box 181
Sunbury, OH 43074
BEFORE YOU BEGIN
Congratulations! And Thank You for purchasing the BODYCRAFT SPT INDOOR
TRAINING CYCLE. The SPT is a high quality way to promote cardiovascular
wellness and lower body strength conditioning .
For your safety and benefits, read this manual and the accompanying literature before
using the SPT INDOOR TRAINING CYCLE. Keep this manual for future
reference.If you have additional questions, please call your local BODYCRAFT
dealers or our customer service department at 800-990-5556 Monday through Friday,
9:00 am until 5:00 pm Eastern Time.
IMPORTANT SAFETY NOTES
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your physician.
This is especially important for individuals over the age of 35 or persons
with pre-existing health problems. Recreation Supply, Inc. assumes no
responsibility for personal injury or property damage sustained by or
through use of this product.
T
.
g
adjust
beyond the marked
T
1
EXPLODED 1
2
EXPLODED 2
3
STEP 1 FRONT AND REAR STABILIZER
1. Attach Front Stabilizer (7) to Main Frame (1) on a flat level
surface floor, using two M8 X 4" Domed Bolts (3A), two M8
Washers (6)
2. Attach Rear Stabilizer (2) to Main Frame (1) on a flat level
surface floor, using two M8 X 4" Domed Bolts (3), two M8
Washers (6)
3 There are Height Adjusters (72) underneath the Rear End
Caps (54,58) that need to be adjusted until the bike is
totally stable on the floor.
FRONT
REAR
6
STEP 2 ASSEMBLE PEDALS
1. Carefully align the threads of the axle on the Right Pedal (70R)
("R" on end of axle) with the threaded hole on the right crank
arm and screw in clockwise by hand. Tighten the pedal to the
crank arm using a 15mm wrench.
2. Repeat the procedure for the left side, but screw the Left Pedal
(70L) in counter-clockwise.
IMPORTANT: First assemble pedals by HAND, not using a wrench. It is
important to match threads exactly. Using a wrench to start the
procedure can easily damage the crank threads. This problem is not
covered under warranty!
PEDAL
7
STEP 3 ASSEMBLE HANDLEBAR AND STEM
1. Insert the Handlebar Post (20) into the front tube on Main
Frame (1). You will be able to adjust the height of the
Handlebar Post and then tighten using the preinstalled
Locking Lever (18). If you do not have room to turn the handle
on the Locking Lever, it can disengage from the covered
screw by simply pulling outward on the handle. Then place
the handle where needed to complete tightening, release, and
it will re-engage with the covered screw. Remember to not
make any adjustments past the marked safety line.
2. Remove the preinstalled Sliders Safety screw (14) on the
front of the Handlebar Stem (20) .Then slide Handlebar Slider
(13) into Handlebar stem from back side (20) .Re-insert the
Sliders Safety Screw (19) Insert End cap (74) into the front of
the Handlebar slider (13) and tighten. This Sliders Safety
Screw (14) keeps the Handlebar from sliding all the way off.
8
STEP 4 ASSEMBLE SEAT AND SEAT POST
1. Insert the Seat Post (15) into the rear tube on Main Frame (1).
You will be able to adjust the height of the seat Post and then
tighten using the preinstalled Locking Lever (18). If you do not
have room to turn the handle on the Locking Lever, it can
disengage from the covered screw by simply pulling outward
on the handle. Then place the handle where needed to
complete tightening, release, and it will re-engage with the
covered screw. Remember to not make any adjustments
past the marked safety line.
2. Remove the preinstalled Sliders Safety Screw (16) on the rear
of the Seat Post (14) and then slide the Seat Sliding Housing
(15) onto the seat Post (14). Re-insert the Sliders Safety screw
(16) and tighten. This Sliders Safety Screw (16) keeps the seat
from sliding all the way off.
3. Attach Seat (17). and Adjust to desired angle, then tighten.
9
Assembly is complete! Please take the following steps before using the
Bodycraft SPT INDOOR TRAINING CYCLE:
1. Make certain all bolts are tightened securely.
2. Steel Seat Post (14) and Steel Handlebar Stem (13) are adjusted to your personal
desired height and locked with the Lock Lever (17). Note: You can pull the Lock
Lever to position the lever away from the frame if needed. Then release the lever and
screw tight.
3. Wipe sweat away after every use. Failure to do so may result in a rusty bike.
4. Do not over tighten the V-Block fixed screws (21) . The depth is preset at the factory.
Over tightening can result in stripped threads.
5. Enjoy many years of a fit lifestyle!
Thank you for purchasing the BodyCraft SPT Indoor Training Cycle.
If you have any questions, please call your local BodyCraft dealer,
call our customer service department at 800-990-5556 or at
http://www.bodycraft.com.
T
T
5
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement