advertisement
▼
Scroll to page 2
PROJECT ITEM # QUANTITY DATE APPROVAL F17C Self-Contained Refrigerated Base Equipment Stands Long Form Specifications Top is constructed of 18-gauge stainless steel, with integral front marine edge nosing and rear backsplash. Spline bars made of 12gauge stainless steel and run front to back on both the left and right stainless steel sides for support and spline purposes. Interior subtop made of 22 gauge 2BF stainless steel is made integral with the top by injecting 2.00” of high density polyurethane foam between the exterior and interior tops. As a standard, 14-gauge cutting board brackets are attached to each side and house a 1.25” thick x 9.5” deep maple cutting board. Refrigerated base interior back and bottom is constructed of 22-gauge 2BF stainless steel. Exterior sides are constructed of 18-gauge stainless steel. Bottom and back are made of 22 gauge galvanized steel. Both left and right interior sides are formed of ABS plastic. The base is injected with 2.00” of high density polyurethane foam between the exterior and interior. Refrigerated base fronts are made of .095” thick ABS thermoformed plastic and backed up by ridged polyurethane water blown injection molded frames. The frames are an excellent thermo-break and superior structural material for fastening doors and drawers. Exterior machine compartment side is constructed of 18-gauge galvanized steel. Single units are supplied with wall-mounted bracket and threaded rod to allow installation of the unit against a solid surface. Units shipped, as part of a line-up do not come standard with a wall mounted bracket assembly. Full Extension Plus drawer system is a complete drawer system, which can operate independent of the unit it’s installed in. Drawer system is sized to hold 12 x 20 x 4 “ deep hotel pans and smaller fractional pans. Drawer system is all stainless steel construction for maximum durability. Outer drawer track is made of 11-gauge stainless and held in place with 12-gauge up-right and cross supports. Drawer track rollers are made of Delrin™ 100 NC-10 and do not require grease for operation. Intermediate tracks are removable without tools and house Delfield’s “anti-friction binary roller system”. Drawer boxes are designed with “easy pan grip flanges”. Tracks are designed with a stay shut feature that holds the drawer gasket tight to the base front on uneven floors. Exterior drawer fronts are made of 22- gauge stainless steel; and an interior made of ABS plastic with formed in channels to house the snap-in dart style santoprene gasket. A 12-gauge galvanized brace is foamed in place to be an integral part of the drawer front assembly. Each drawer front is injected with 1.87” of high density polyurethane foam between the exterior and interior. Handles are recessed black plastic and held in with a positive lock system. Model F17C68 Unit is supported with two 14-gauge leg rails that run the entire length of the unit. Leg rails are welded to the bottom side of the unit and are tied together with two 12-gauge braces running front to back. Caster/leg boxes are welded inside the leg rail and 6.12” adjustable stainless steel legs are mounted as standard with (4) 5/16” bolts. Self-contained models have a pre-wired condensing unit and a digital thermometer installed in the machine compartments (standard on right) louver panel and supplied with an 8’ cord and plug. Interior refrigerated base cabinet will maintain 36 to 40 degree temperatures at 100-degree ambient room temperature. Refrigeration system components are HFC-404A. Interior cabinet is cooled with mullion style blower coils (coated) mounted between each door/drawer section for even air and temperature control. Electrical connections are 115V-60H-1PH. Optional Accessories and Modifications 505B 906A 505F 905A 906E 1027A 104 108 213 Stainless steel back Stainless steel end Laminate facing (drawers only) Laminate back Laminate end Casters Doors, except 32" Locks *220V/50 cycle electrical *Inclusion of this option will alter electrical specifications. The Delfield Company, 980 S. Isabella Rd., Mt Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com Delfield reserves the right to make changes in design or specifications without prior notice. ©2003 The Delfield Company. All rights reserved. Printed in U.S.A. F17C Self-Contained Refrigerated Base Equipment Stands 52" [132.1cm] 60" [152.4cm] 68" [172.7cm] 78" [198.1cm] 50" [127cm] 58" [147.3cm] 66" [168cm] 76" [193cm] 32" (81.3cm) REF'G 19" (48.3cm) 27" (68.6cm) REF'G 27" (68.6cm) REF'G 27" (68.6cm) REF'G 32" (81.3cm) REF'G 32" (81.3cm) REF'G 32" (81.3cm) REF'G 19" (48.3cm) 27" (68.6cm) REF'G 27" (68.6cm) REF'G 27" (68.6cm) REF'G 32" (81.3cm) REF'G 32" (81.3cm) REF'G 6" [15.2cm] 1/5 HP 115V-60C-1PH 14" [35.6cm] 1/5 HP 115V-60C-1PH ELEVATION VIEW F17C52 14" [35.6cm] ELEVATION VIEW F17C60 14" [35.6cm] 1/5 HP 115V-60C-1PH 85" [216cm] 14" [35.6cm] ELEVATION VIEW F17C78 ELEVATION VIEW F17C68 87" [221cm] 27" (68.6cm) REF'G 1/5 HP 115V-60C-1PH 95" [241.3cm] 110" [279.4cm] 93" [236cm] 108" [274cm] 19" (48.3cm) 27" (68.6cm) REF'G 27" (68.6cm) REF'G 27" (68.6cm) REF'G 27" (68.6cm) REF'G 32" (81.3cm) REF'G 32" (81.3cm) REF'G 32" (81.3cm) REF'G 27" (68.6cm) REF'G 19" (48.3cm) 27" (68.6cm) REF'G 27" (68.6cm) REF'G 27" (68.6cm) REF'G 27" (68.6cm) REF'G 32" (81.3cm) REF'G 32" (81.3cm) REF'G 32" (81.3cm) REF'G 1/4 HP 115V-60C-1PH 14" [35.6cm] 14" 1/4 HP 115V-60C-1PH [35.6cm] ELEVATION VIEW F17C87 14" 1/4 HP 115V-60C-1PH [35.6cm] ELEVATION VIEW F17C110 ELEVATION VIEW F17C95 30.74" 78.07cm 2.00" 5.08cm 30.74" 78.1cm 26.08" (66.24cm) (19", 24", 32" drawers) 28.18 (71.57cm) (27" drawers) 40.00" 101.6cm 9.5" 24cm END VIEW ALL MODELS 36.00" 91.44cm 26.00" 66.04cm 25.50" 64.77cm 7.62" 6.13" 19.38cm 15.57cm END VIEW ALL MODELS Mechanical Data–Standard Unit MODEL NUMBER NUMBER OF DRAWERS PAN* CAPACITY H.P. VOLTS, HERTZ PHASE AMPS BTU DESIGN LOAD BTU SYSTEM CAPACITY SHIP WEIGHT F17C52 (2) 32” 4 1/5 115/60/1 8.0 452 1727 410 lbs/ 186 kg F17C60 (2) 19 & (2) 27” 6 1/5 115/60/1 8.0 556 1727 460 lbs/ 208 kg F17C68 (4) 27” 8 1/5 115/60/1 8.0 632 1727 500 lbs/ 227 kg F17C78 (4) 32” 8 1/5 115/60/1 8.0 726 1727 580 lbs/ 263 kg F17C87 (2) 19 & (4) 27” 10 1/4 115/60/1 10.0 868 2341 625 lbs/ 283 kg F17C95 (6) 27” 12 1/4 115/60/1 10.0 1001 2341 700 lbs/ 317 kg F17C110 (6) 32” 12 1/4 115/60/1 10.0 1143 2341 750 lbs/ 340 kg *12” x 20” x 4” deep pans not included. 5-15P NEMA plug used on all lengths. The Delfield Company, 980 S. Isabella Rd., Mt Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com Delfield reserves the right to make changes in design or specifications without prior notice. ©2003 The Delfield Company. All rights reserved. Printed in U.S.A. DS17C 04/03
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project