- Computers & electronics
- TVs & monitors
- Wall & ceiling mounts accessories
- Glastender
- DI-FR-DW
- Data Sheet
advertisement
▼
Scroll to page 2
Project: Item #: Model #: AIA# Qty: SIS# Drop-In Ice Cream Freezers DI-FR, DI-FR-DW, DI-FR36, DI-FR36-FL, DI-FR36-DW or DI-FR36-DW-FL Standard Features • Stainless steel work surface, lid, and interior liner with galvanized steel exterior wrap • CFC Free foamed-in-place insulation • Available with integral 6″ diameter draining dipper well and faucet • Six foot grounded cord and plug provided • Available sizes for one or two 3-gallon containers • Refer to reverse side for mounting instructions • Special angle brackets, U-channels, and mounting bolts provided for easy installation DI-FR-DW NOTE: The standard top lifts up and the special hinges allow the lid to remain open while dipping. A special “flip lid” is available on the models that hold two 3-gallon containers. The flip lid is hinged in the middle and opens from each end. The flip lid models are specified with the suffix ‘-FL’ on the end of the model number. DI-FR36-FL Specifications Drains • 1-1/2″ I.P.S. (when ordered with dipper well) Threaded drain will fit Dearborn part #8033 slipnut and part #W-573P washer. Faucet • Accepts 3/8″ cold water leads (when ordered with dipper well) Capacities • DI-FR models holds one 3-gallon container • DI-FR36 models holds two 3-gallon containers Inside Dimensions • DI-FR models- 10 x 10 x 12 1/2 • DI-FR36 models- 10 x 20 x 12 1/2 Electrical • 120V, 1 phase, 60 Hz, 4.2 full load amps • Dedicated 15 amp circuit is recommended • Includes 6 foot grounded cord and plug Refrigeration • 1/5 HP, R404A refrigerant Operating Range • -5°F to 10°F Materials • 20 gauge stainless steel parts include: work surface, interior liner, lid, and dipper well • 22 gauge galvanized steel parts include: exterior wrap • 16 gauge galvanized steel parts include: base plate Angle mounting bracket U-channel Mounting bolt DI-FR shown installed in countertop Glastender, Inc. • 5400 North Michigan Road • Saginaw, MI • 48604-9780 989.752.4275 • 800.748.0423 • Fax 989.752.4444 www.glastender.com Approval/Notes: Specifications subject to change without notice. For current specifications please visit our website. Printed in USA 6.05 Rev.11-16-07 Drop-In Ice Cream Freezers Dimensional Information PLAN VIEWS CUT-OUT DIMENSION 14-3/4" X 14-3/4" CUT-OUT DIMENSION 22-3/4" X 14-3/4" 18" 14" 24" AIR FLOW AIR FLOW AIR FLOW AIR FLOW 14" CUT-OUT DIMENSION 32-3/4" X 14-3/4" CUT-OUT DIMENSION 24-3/4" X 14-3/4" 34" 28" 24" COLD WATER 24" 14" 18" 14" 18" 18" DRAIN MINIMUM 5" CLEARANCE FOR AIR FLOW DI-FR MINIMUM 5" CLEARANCE FOR AIR FLOW DI-FR-DW DI-FR36 DI-FR36-FL DI-FR36-DW DI-FR36-DW-FL 6-1/4" 6-1/4" 22" 22" DRAIN 24" 14" FRONT VIEWS COUNTER TOP ANGLE BRACKET U-CHANNEL SCREW BOLT SIDE ELEVATION COUNTER TOP COUNTER TOP INSTALLATION INSTRUCTIONS DI-FR 1. Remove angle brackets from drop-in ice cream freezer. 2. Place freezer into appropriate size cut-out for specific model number used. 3. Replace angle brackets, firmly tighten screws. 4. Place U-channels on top of bolts. 5. Tighten each bolt evenly along U-channels. 6. Seal as necessary. DI-FR-DW NOTE: AIR FLOW RESTRICTION WILL CAUSE COMPRESSOR FAILURE AND VOID WARRANTY. 5400 North Michigan Road • Saginaw, MI • 48604-9780 989.752.4275 • 800.748.0423 • Fax 989.752.4444 www.glastender.com Printed in USA
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project