Toyota Prius C Owner's manual

Toyota Prius C Owner's manual
Introduction
NAVIGATION SYSTEM OWNER’S MANUAL
This manual explains the operation of the system. Please read this manual
carefully to ensure proper use. Keep this manual in your vehicle at all times.
The screen shots in this document and the actual screens of the system differ
depending on whether the functions and/or a contract existed and the map data
available at the time of producing this document.
Please be aware that the content of this manual may be different from the system in some cases, such as when the system’s software is updated.
NAVIGATION SYSTEM
The Navigation System is one of the most technologically advanced vehicle accessories ever developed. The system receives satellite signals from the Global
Positioning System (GPS) operated by the U.S. Department of Defense. Using
these signals and other vehicle sensors, the system indicates your present position and assists in locating a desired destination.
The navigation system is designed to select efficient routes from your present
starting location to your destination. The system is also designed to direct you
to a destination that is unfamiliar to you in an efficient manner. The system uses
AISIN AW maps. The calculated routes may not be the shortest nor the least
traffic congested. Your own personal local knowledge or “short cut” may at
times be faster than the calculated routes.
The navigation system’s database includes Point of Interest categories to allow
you to easily select destinations such as restaurants and hotels. If a destination
is not in the database, you can enter the street address or a major intersection
close to it and the system will guide you there.
The system will provide both a visual map and audio instructions. The audio instructions will announce the distance remaining and the direction to turn in when
approaching an intersection. These voice instructions will help you keep your
eyes on the road and are timed to provide enough time to allow you to maneuver, change lanes or slow down.
Please be aware that all current vehicle navigation systems have certain limitations that may affect their ability to perform properly. The accuracy of the vehicle’s position depends on satellite conditions, road configuration, vehicle
condition or other circumstances. For more information on the limitations of the
system, refer to page 250.
2
IMPORTANT INFORMATION ABOUT THIS MANUAL
For safety reasons, this manual indicates items requiring particular attention
with the following marks.
WARNING
● This is a warning against anything which may cause injury to people if the warning is
ignored. You are informed about what you must or must not do in order to reduce the risk
of injury to yourself and others.
NOTICE
● This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in
order to avoid or reduce the risk of damage to your vehicle and its equipment.
SYMBOLS USED IN ILLUSTRATIONS
Safety symbol
The symbol of a circle with a slash through it means “Do not”, “Do not do
this” or “Do not let this happen”.
Arrows indicating operations
Indicates the action (pushing, turning,
etc.) used to operate switches and other
devices.
3
HOW TO READ THIS MANUAL
No.
4
Name
Description
Operational
Outlines
An outline of the operation is explained.
Main Operations
The steps of an operation are explained.
Related Operations
A main operation’s supplementary operations are described.
Information
Useful information for the user is described.
SAFETY INSTRUCTION
To use this system in the safest possible
manner, follow all the safety tips shown
below.
This system is intended to assist in reaching the destination and, if used properly,
can do so. The driver is solely responsible
for the safe operation of your vehicle and
the safety of your passengers.
Do not use any feature of this system to
the extent it becomes a distraction and
prevents safe driving. The first priority
while driving should always be the safe operation of the vehicle. While driving, be
sure to observe all traffic regulations.
Prior to the actual use of this system, learn
how to use it and become thoroughly familiar with it. Read the entire manual to make
sure you understand the system. Do not
allow other people to use this system until
they have read and understood the instructions in this manual.
For your safety, some functions may become inoperable when driving. Unavailable screen buttons are dimmed. Only
when the vehicle is not moving, can the
destination and route selection be done.
WARNING
● For safety, the driver should not operate
the system while he/she is driving. Insufficient attention to the road and traffic
may cause an accident.
● While driving, be sure to obey the traffic
regulations and maintain awareness of
the road conditions. If a traffic sign on
the road has been changed, route guidance may not have the updated information such as the direction of a one way
street.
While driving, listen to the voice instructions as much as possible and glance at
the screen briefly and only when it is safe.
However, do not totally rely on voice guidance. Use it just for reference. If the system cannot determine the current position
correctly, there is a possibility of incorrect,
late, or non-voice guidance.
The data in the system may occasionally
be incomplete. Road conditions, including
driving restrictions (no left turns, street closures, etc.) frequently change. Therefore,
before following any instructions from the
system, look to see whether the instruction
can be done safely and legally.
This system cannot warn about such
things as the safety of an area, condition of
streets, and availability of emergency services. If unsure about the safety of an area, do not drive into it. Under no
circumstances is this system a substitute
for the driver’s personal judgement.
Use this system only in locations where it
is legal to do so. Some states/provinces
may have laws prohibiting the use of video
and navigation screens next to the driver.
5
TABLE OF CONTENTS
1
QUICK GUIDE
1. BASIC FUNCTION........................... 10
2
BASIC FUNCTION
OVERVIEW BUTTONS ......................... 10
1. BASIC INFORMATION BEFORE
OPERATION.................................. 30
“Apps” SCREEN .................................... 12
INITIAL SCREEN ................................... 30
HOME SCREEN .................................... 14
TOUCH SCREEN GESTURES.............. 32
2. QUICK REFERENCE....................... 18
TOUCH SCREEN OPERATION ............ 33
“Setup” SCREEN ................................... 18
3. NAVIGATION OPERATION ............ 20
REGISTERING HOME .......................... 20
REGISTERING PRESET
DESTINATIONS.................................. 22
OPERATION FLOW:
GUIDING THE ROUTE ....................... 24
SETTING HOME AS
THE DESTINATION ............................ 25
4. FUNCTION INDEX........................... 26
FUNCTION INDEX ................................ 26
HOME SCREEN OPERATION .............. 34
ENTERING LETTERS AND
NUMBERS/LIST SCREEN
OPERATION........................................ 35
SCREEN ADJUSTMENT ....................... 38
2. Bluetooth® SETTINGS ................... 40
REGISTERING/CONNECTING
Bluetooth® DEVICE ............................. 40
SETTING Bluetooth® DETAILS ............. 44
3. OTHER SETTINGS ......................... 52
GENERAL SETTINGS ........................... 52
VOICE SETTINGS ................................. 58
VEHICLE SETTINGS ............................. 59
DRIVER SETTINGS............................... 60
MAINTENANCE ..................................... 61
6
3
AUDIO SYSTEM
5
INFORMATION
1
1. BASIC OPERATION........................ 66
1. USEFUL INFORMATION .............. 136
QUICK REFERENCE ............................ 66
RECEIVING WEATHER
INFORMATION ................................. 136
SOME BASICS...................................... 67
DATA SERVICES SETTINGS ............. 138
2. RADIO OPERATION ....................... 72
AM/FM RADIO....................................... 72
XM Satellite Radio ................................. 82
6
INTERNET RADIO ................................ 89
3. MEDIA OPERATION ....................... 90
PERIPHERAL MONITORING
SYSTEM
1. REAR VIEW MONITOR
SYSTEM ...................................... 140
USB MEMORY ...................................... 94
REAR VIEW MONITOR SYSTEM ....... 140
iPod ....................................................... 99
Bluetooth® AUDIO ............................... 104
REAR VIEW MONITOR SYSTEM
PRECAUTIONS ................................ 142
AUX ..................................................... 109
THINGS YOU SHOULD KNOW .......... 147
STEERING SWITCHES ...................... 112
5. SETUP ........................................... 114
AUDIO SETTINGS .............................. 114
6. TIPS FOR OPERATING
THE AUDIO SYSTEM .................. 116
OPERATING INFORMATION ............. 116
7
PHONE
VOICE COMMAND SYSTEM
1. VOICE COMMAND SYSTEM
OPERATION ................................ 126
VOICE COMMAND SYSTEM.............. 126
CASUAL SPEECH
RECOGNIZATION ............................ 132
COMMAND LIST ................................. 133
5
6
7
1. PHONE OPERATION
(HANDS-FREE SYSTEM
FOR CELLULAR PHONES)........ 150
QUICK REFERENCE .......................... 150
SOME BASICS .................................... 151
®
4
3
4
CD ......................................................... 90
4. AUDIO REMOTE CONTROLS ...... 112
2
CALLING ON THE Bluetooth
PHONE.............................................. 154
RECEIVING ON THE Bluetooth®
PHONE.............................................. 159
TALKING ON THE Bluetooth®
PHONE.............................................. 160
Bluetooth® PHONE MESSAGE
FUNCTION ........................................ 163
2. SETUP........................................... 168
PHONE/MESSAGE SETTINGS .......... 168
3. WHAT TO DO IF... ....................... 180
TROUBLESHOOTING......................... 180
7
8
9
TABLE OF CONTENTS
8
NAVIGATION SYSTEM
9
Entune App Suite
1. BASIC OPERATION...................... 188
1. Entune App Suite OVERVIEW .... 256
QUICK REFERENCE .......................... 188
Entune App Suite SERVICE................. 256
MAP SCREEN OPERATION ............... 191
MAP SCREEN INFORMATION ........... 197
2. Entune App Suite
OPERATION................................ 261
TRAFFIC INFORMATION.................... 201
Entune App Suite ................................. 261
2. DESTINATION SEARCH............... 204
DESTINATION SEARCH SCREEN..... 204
3. SETUP........................................... 268
Entune App Suite SETTINGS .............. 268
SEARCH OPERATION........................ 206
STARTING ROUTE GUIDANCE ......... 216
INDEX
3. ROUTE GUIDANCE....................... 220
ROUTE GUIDANCE SCREEN ............ 220
TYPICAL VOICE GUIDANCE
PROMPTS......................................... 225
EDITING ROUTE................................. 226
4. MEMORY POINTS......................... 231
MEMORY POINTS SETTINGS ........... 231
5. SETUP ........................................... 240
DETAILED NAVIGATION
SETTINGS ........................................ 240
TRAFFIC SETTINGS........................... 244
6. TIPS FOR THE NAVIGATION
SYSTEM ....................................... 250
GPS (GLOBAL POSITIONING
SYSTEM) .......................................... 250
MAP DATABASE VERSION AND
COVERED AREA.............................. 252
8
ALPHABETICAL INDEX................... 272
1
1
QUICK GUIDE
2
1
BASIC FUNCTION
3
1. OVERVIEW BUTTONS ................. 10
4
2. “Apps” SCREEN .......................... 12
3. HOME SCREEN ............................ 14
5
STATUS DISPLAY................................. 16
2
6
QUICK REFERENCE
1. “Setup” SCREEN ......................... 18
3
7
NAVIGATION OPERATION
8
1. REGISTERING HOME .................. 20
2. REGISTERING PRESET
DESTINATIONS .......................... 22
3. OPERATION FLOW:
GUIDING THE ROUTE................ 24
4. SETTING HOME AS
THE DESTINATION .................... 25
4
FUNCTION INDEX
1. FUNCTION INDEX ........................ 26
9
9
1. BASIC FUNCTION
1. OVERVIEW BUTTONS
10
1. BASIC FUNCTION
No.
Page
By touching the screen with your finger, you can control the selected
functions.
32, 33
Insert a disc into this slot. The CD player turns on immediately.
69
Press to access the Bluetooth® hands-free system.
150
Press to display the “Apps” screen.
12
Press to display the home screen.
14, 34
Turn to select a radio station or skip to the next or previous track/file.
72, 82, 90,
94, 99, 104
MAP card slot
Do not eject the micro SD card, as doing so may deactivate the navigation system.
253
Press to access the audio system. The audio system turns on in the
last mode used.
66, 67, 68
Press to turn the audio system on and off, and turn it to adjust the volume.
67
Press the “ ” or “ ” button to seek up or down for a radio station or to
access a desired track/file.
72, 82, 90,
94, 99, 104
Press to eject a disc.
1
QUICK GUIDE
Function
69
11
1. BASIC FUNCTION
2. “Apps” SCREEN
Press the “APPS” button to display the “Apps” screen.
12
1. BASIC FUNCTION
No.
Function
Page
188
Select to display the audio control screen.
66
Select to display the phone top screen.
150
Select to display the “Message Inbox” screen.
163
Select to display weather information.
136
Select to display traffic information.
201
1
QUICK GUIDE
Select to display the map screen.
Select to reorder the applications.
263
 Select the desired application then
or
to reorder.
Select to display the “Setup” screen.
18
Select to update the applications.
262
Select to display the energy monitor/fuel consumption screen.
“Owner’s
Manual”
Select to display the “Maintenance” screen.
61
Select to display the application screen.
261
INFORMATION
● When there are two pages, select
or
to change the page.
13
1. BASIC FUNCTION
3. HOME SCREEN
Press the “HOME” button to display the home screen.
The home screen can display multiple information screens, such as the audio system screen, hands-free screen and navigation screen, simultaneously. When
hands-free mode is selected, it is possible to make a call on the home screen if the
desired phone number is registered to one of the 4 displayed buttons. In order to
register the contact, select and hold the desired button and register the desired
contact by obey displayed messages on the screen. (P.158)
When a screen is selected, the selected screen is switched to a full-screen display.
The home screen can be set to either a three-way split screen or a two-way split
screen.
For details about setting the home screen: P.34
Three-way split screen
14
1. BASIC FUNCTION
Two-way split screen
1
QUICK GUIDE
No.
Function
Page
Displays the condition of the Bluetooth® connection
16
Select to display the “Setup” screen.
18
15
1. BASIC FUNCTION
STATUS DISPLAY
The condition of the Bluetooth® connection, as well as the level of reception and
the amount of cellular phone battery charge left, are displayed on the status display.
No.
Indicators
Conditions
(Gray)
No connection
The condition of
the
Bluetooth®
connection
The level of reception
16
Poor
(Blue)
Good
 An antenna for the Bluetooth® connection is built into the instrument panel. The condition of the Bluetooth® connection may deteriorate and the system may not function when a Bluetooth® phone
is used in the following conditions and/or places:
The cellular phone is obstructed by certain objects (such as when
it is behind the seat or in the glove box or console box).
The cellular phone is touching or is covered with metal materials.
 Leave the Bluetooth® phone in a place where the condition of the
Bluetooth® connection is good.
Poor
Excellent
 The level of reception does not always correspond with the level
displayed on the cellular phone. The level of reception may not be
displayed depending on the phone you have.
When the cellular phone is out of the service area or in a place
inaccessible by radio waves, “No Service” is displayed.
 “Rm” is displayed when receiving in a roaming area. While roaming, display “Rm” top-left on the icon.
 The receiving area may not be displayed depending on the type of
phone you have.
1. BASIC FUNCTION
No.
Indicators
Conditions
The amount of
battery
charge
left
Empty
Full
 The amount displayed does not always correspond with the
amount displayed on the Bluetooth® device.
The amount of battery charge left may not be displayed depending on the type of the Bluetooth® device connected.
This system does not have a charging function.
1
QUICK GUIDE
17
2. QUICK REFERENCE
1. “Setup” SCREEN
The items shown on the “Setup” screen can be set. Press the “APPS” button, then
select “Setup” to display the “Setup” screen.
18
2. QUICK REFERENCE
No.
Page
Select to change the selected language, operation sound, automatic
screen change settings, etc.
52
Select to customize the home screen.
34
Select to set the voice settings.
58
Select to adjust the contrast and brightness of the screens.
38
Select to set memory points (home, preset destinations, address book
entries, areas to avoid), navigation details or to delete previous destinations.
1
QUICK GUIDE
Function
231, 240
Select to set audio settings.
114
Select to set the phone sound, contacts, message settings, etc.
168
Select to set Bluetooth® phones and Bluetooth® audio devices.
44
Select to turn the screen off.

Select to set Entune App Suite settings.
268
Select to set data services settings.
138
Select to link the driver’s cellular phone settings. (audio presets, language, etc.)
60
Select to set vehicle information.
59
Select to set traffic information.
244
19
3. NAVIGATION OPERATION
1. REGISTERING HOME
1
2
3
20
Press the “APPS” button.
4
Select “Go Home”.
5
Select “Yes”.
6
There are different kinds of methods to search for your home.
(P.204)
Select “Navigation”.
Select “Dest.”.
3. NAVIGATION OPERATION
7
Select “Enter”.
1
QUICK GUIDE
8
Select “OK”.
Registration of home is complete.
Registering home in a different way
P.232
Editing the name, location, phone number and icon
P.232
Setting home as the destination
P.207
21
3. NAVIGATION OPERATION
2. REGISTERING PRESET DESTINATIONS
1
Press the “APPS” button.
2
Select “Navigation”.
3
22
Select “Dest.”.
4
Select one of the preset destination buttons.
5
Select “Yes”.
6
There are different kinds of methods to search for a destination.
(P.204)
3. NAVIGATION OPERATION
7
Select “Enter”.
1
Select a position for this preset
destination.
9
Select “OK”.
QUICK GUIDE
8
Registration of preset destinations is
complete.
Registering preset destinations in a different way
P.233
Editing the name, location, phone number and icon
P.234
Setting preset destinations as the destination
P.207
23
3. NAVIGATION OPERATION
3. OPERATION FLOW: GUIDING THE ROUTE
1
Press the “APPS” button.
5
Select “Go”.
6
2
Select “Navigation”.
Select “OK”.
Selecting routes other than the one recommended. (P.216)
Guidance to the destination is displayed
on the screen and can be heard via
voice guidance.
3
Select “Dest.”.
4
There are different kinds of methods to search for a destination.
(P.204)
24
3. NAVIGATION OPERATION
4. SETTING HOME AS THE DESTINATION
1
Press the “APPS” button.
Guidance to the destination is displayed
on the screen and can be heard via
voice guidance.
2
Select “Navigation”.
3
Select “Dest.”.
4
Select “Go Home”.
25
1
QUICK GUIDE
5 Select “OK”.
Selecting routes other than the one recommended. (P.216)
4. FUNCTION INDEX
1. FUNCTION INDEX
Map
Displaying maps
Page
Viewing the map screen
188
Displaying the current position
191
Viewing the current position vicinity map
195
Changing the scale
191
Changing the map orientation
192
Displaying map information
197
Displaying the estimated travel/arrival time to the destination
220
Selecting the map mode
193
Displaying traffic information
201
Searching for destinations
Page
Searching for the destination
206
Changing the search area
207
Route guidance
Before starting or during route guidance
Page
Starting route guide
216
Editing the route
226
Viewing the entire route map
221
Pausing guidance
219
Adjusting route guidance volume
58
Deleting the destination
227
Address book
Page
Registering address book entries
235
Marking icons on the map
236
26
4. FUNCTION INDEX
Useful functions
1
Information
Hands-free system (for cellular phone)
Registering/connecting
Bluetooth® phone
®
61
Page
40
Making a call on a Bluetooth phone
154
Receiving a call on the Bluetooth® phone
159
Voice command system
Operating the system with your voice
Peripheral monitoring system
Viewing behind the rear of the vehicle
QUICK GUIDE
Displaying vehicle maintenance
Page
Page
126
Page
140
27
4. FUNCTION INDEX
28
2
1
BASIC FUNCTION
2
1
BASIC INFORMATION BEFORE
OPERATION
2. SETTING Bluetooth®
DETAILS ..................................... 44
3
“Bluetooth* Setup” SCREEN.................. 44
1. INITIAL SCREEN ........................... 30
REGISTERING A Bluetooth®
DEVICE ............................................... 45
2. TOUCH SCREEN GESTURES ...... 32
DELETING A Bluetooth® DEVICE ......... 46
CONNECTING A Bluetooth®
DEVICE ............................................... 47
3. TOUCH SCREEN
OPERATION ................................ 33
EDITING THE Bluetooth® DEVICE
INFORMATION ................................... 49
4. HOME SCREEN OPERATION ...... 34
4
5
6
“System Settings” SCREEN................... 50
5. ENTERING LETTERS AND
NUMBERS/LIST SCREEN
OPERATION ................................ 35
3
7
OTHER SETTINGS
ENTERING LETTERS AND
NUMBERS .......................................... 35
1. GENERAL SETTINGS .................. 52
LIST SCREEN ....................................... 35
GENERAL SETTINGS SCREEN ........... 52
6. SCREEN ADJUSTMENT ............... 38
2. VOICE SETTINGS......................... 58
VOICE SETTINGS SCREEN ................. 58
2
Bluetooth® SETTINGS
3. VEHICLE SETTINGS .................... 59
1. REGISTERING/CONNECTING
Bluetooth® DEVICE .................... 40
REGISTERING A Bluetooth® PHONE
FOR THE FIRST TIME ....................... 40
REGISTERING A Bluetooth® AUDIO
PLAYER FOR THE FIRST TIME ........ 41
4. DRIVER SETTINGS ...................... 60
MANUALLY SELECT LINKED
SETTINGS .......................................... 60
5. MAINTENANCE ............................ 61
PROFILES ............................................. 42
CERTIFICATION ................................... 43
*: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
29
8
9
1. BASIC INFORMATION BEFORE OPERATION
1. INITIAL SCREEN
1
When the power switch is turned to
ACCESSORY or ON mode, the initial
screen will be displayed and the system will begin operating.
MAINTENANCE INFORMATION
This system reminds users when to replace certain parts or components and
shows dealer information (if registered) on the screen.
When the vehicle reaches a previously
set driving distance or date specified
for a scheduled maintenance check,
the “Maintenance Reminder” screen
will be displayed when the system is
turned on.
 Images shown on the initial screen can
be changed to suit individual preferences. (P.55.)
 After a few seconds, the “Caution” screen
will be displayed.
 After about 5 seconds, the “Caution”
screen automatically switches to the next
screen.
WARNING
● When the vehicle is stopped with the
hybrid system operating, always apply
the parking brake for safety.
 The screen goes off if the screen is not
operated for several seconds.
 To prevent the screen from being displayed again, select “Do Not Tell Me
Again”.
 To register maintenance information:
P.61
 If
is selected, the registered
phone number can be called.
30
1. BASIC INFORMATION BEFORE OPERATION
RESTARTING THE SYSTEM
When system response is extremely
slow, the system can be restarted.
2
1
BASIC FUNCTION
Press and hold the “PWR·VOL” knob
for 3 seconds or more.
31
1. BASIC INFORMATION BEFORE OPERATION
2. TOUCH SCREEN GESTURES
Operations are performed by touching the touch screen directly with your finger.
Operation method
Outline
Main use
Touch
Quickly touch and release
once.
Changing and selecting various settings
Drag*
Touch the screen with
your finger, and move the
screen to the desired position.
Flick*
Quickly move the screen
by flicking with your finger.
 Scrolling the lists
 Scrolling the map screen
 Scrolling the main screen page
 Scrolling the map screen
*: The above operations may not be performed on all screens.
INFORMATION
● Flick operations may not be performed smoothly in high altitudes.
32
1. BASIC INFORMATION BEFORE OPERATION
3. TOUCH SCREEN OPERATION
This system is operated mainly by the
buttons on the screen. (Referred to as
screen buttons in this manual.)
2
BASIC FUNCTION
 When a screen button is touched, a
beep sounds. (To set the beep sound:
 52)
NOTICE
● To prevent damaging the screen, lightly
touch the screen buttons with your finger.
● Do not use objects other than your finger
to touch the screen.
● Wipe off fingerprints using a glass cleaning cloth. Do not use chemical cleaners
to clean the screen, as they may damage the touch screen.
INFORMATION
● If the system does not respond to touching a screen button, move your finger
away from the screen and then touch it
again.
● Dimmed screen buttons cannot be operated.
● The displayed image may become
darker and moving images may be
slightly distorted when the screen is
cold.
● In extremely cold conditions, the map
may not be displayed and the data input
by a user may be deleted. Also, the
screen buttons may be harder than
usual to depress.
● When you look at the screen through
polarized material such as polarized
sunglasses, the screen may be dark and
hard to see. If so, look at the screen
from different angles, adjust the screen
settings on the “Display Settings” screen
or take off your sunglasses.
● When
select
screen.
is displayed on the screen,
to return to the previous
33
1. BASIC INFORMATION BEFORE OPERATION
4. HOME SCREEN OPERATION
The home screen can display multiple
information screens, such as the audio
system screen and hands-free screen,
simultaneously.
1
2
Press the “HOME” button.
“Home” screen is displayed.
 When a screen is selected, the selected
screen will change to a full-screen display.
CUSTOMIZING THE HOME
SCREEN
The display items/area on the home
screen can be changed.
1
Select
2
Select “Home Screen”.
.
 Select “Two Panel” or “Three Panel”.
3
4
5
Select the desired area.
Select the desired item.
Select “OK”.
INFORMATION
● When the selected item is already being
displayed and another area is selected
for that item, the item that it is replacing
will be displayed in the original item’s
location.
34
1. BASIC INFORMATION BEFORE OPERATION
5. ENTERING LETTERS AND NUMBERS/LIST SCREEN OPERATION
When searching by an address, name,
etc., or entering data, letters and numbers can be entered via the screen.
LIST SCREEN
The list screen may be displayed after
entering characters.
DISPLAYING THE LIST
1
No.
Function
Select to enter desired characters.
Text field. Entered character(s) will
be displayed.
During character entry, when there is
only one available option for the next
character(s), the next character(s)
will be displayed in gray text in the
text field automatically. Gray text is
entered by selecting this button.
Enter characters and select “OK”.
 Matching items from the database are
listed even if the entered address or name
is incomplete.
 The list will be displayed automatically if
the maximum number of characters is
entered or matching items can be displayed on a single list screen.
Select to erase one character. Select
and hold to continue erasing characters.
Select to display the alphabet keys.
Select to display other symbols.
 On certain letter entry screens, letters can
be entered in upper or lower case.
2
BASIC FUNCTION
ENTERING LETTERS AND
NUMBERS
INFORMATION
● The number of matching items is shown
on the right side of the screen. If the
number of matching items is more than
999, the system displays “” on the
screen.
: Select to enter in lower case.
: Select to enter in upper case.
 Keyboard layout can be changed.
(P.52)
35
1. BASIC INFORMATION BEFORE OPERATION
■SELECTING ALL ITEMS
Some lists contain “Select All”. If “Select All” is selected, it is possible to
select all items.
1
LIST SCREEN OPERATION
When a list is displayed, use the appropriate screen button to scroll through
the list.
Select “Select All”.
“Unselect All”: Unselect all items in the
list.
Icon
Function
Select to skip to the next or previous page.
Select and hold
or
to
scroll through the displayed list.
This indicates the
screen’s position.
If
displayed
appears to the right of an
item name, the complete name is
too long to display.
Select
to scroll to the end of
the name.
Select
to move to the begin-
ning of the name.
36
1. BASIC INFORMATION BEFORE OPERATION
SORTING
1
Select “Sort”.
Some lists contain character screen
buttons, “ABC”, “DEF” etc., which allow a direct jump to list entries that begin with the same letter as the
character screen button.
1
2
Select the desired character jump buttons.
Select the desired sorting criteria.
INFORMATION
● Every time the same character screen
button is selected, the list starting with
the subsequent character is displayed.
37
2
BASIC FUNCTION
The order of a list displayed on the
screen can be sorted in the order of
distance from the current location,
date, category, etc.
CHARACTER JUMP BUTTONS
IN LISTS
1. BASIC INFORMATION BEFORE OPERATION
6. SCREEN ADJUSTMENT
The contrast and brightness of the
screen display and the image of the
camera display can be adjusted. The
screen can also be changed to either
day or night mode.
1
Press the “APPS” button.
CHANGING BETWEEN DAY
AND NIGHT MODE
Depending on the position of the headlight switch, the screen changes to day
or night mode. This feature is available
when the headlight is switched on.
1
Select “Day Mode”.
INFORMATION
● If the screen is set to day mode with the
headlight switch turned on, this condition
is memorized even with the hybrid system turned off.
2
3
4
Select “Setup”.
Select “Display”.
Select the items to be set.
No.
Function
Page
Select to adjust the screen
display.
39
Select to adjust the camera
display.
Select to turn day mode on/
off.
38
38
1. BASIC INFORMATION BEFORE OPERATION
ADJUSTING THE CONTRAST/
BRIGHTNESS
The contrast and brightness of the
screen can be adjusted according to
the brightness of your surroundings.
BASIC FUNCTION
1
2
2
Select “General” or “Camera”.
Select the desired item.
General
Camera
Screen button
Function
“Brightness” “+”
Select to brighten the
screen.
“Brightness” “-”
Select to darken the
screen.
“Contrast” “+”
Select to strengthen the
contrast of the screen.
“Contrast” “-”
Select to weaken the
contrast of the screen.
3
Select “OK”.
39
2. Bluetooth® SETTINGS
1. REGISTERING/CONNECTING Bluetooth® DEVICE
REGISTERING A Bluetooth®
PHONE FOR THE FIRST TIME
5
To use the hands-free system, it is
necessary to register a Bluetooth®
phone with the system.
When this screen is displayed, search
for the device name displayed on this
screen on the screen of your
Bluetooth® device.
Once the phone has been registered, it
is possible to use the hands-free system.
This operation cannot be performed
while driving.
For details about registering
Bluetooth® device: P.45
1
a
Turn the Bluetooth® connection setting
of your cellular phone on.
 This function is not available when
Bluetooth® connection setting of your cellular phone is set to off.
2
Press the “APPS” button.
3
Select “Phone”.
 Operations up to this point can also be
performed by pressing the
the steering wheel or
instrument panel.
4
40
switch on
switch on the
Select “Yes” to register a phone.
 For details about operating the Bluetooth®
device, see the manual that comes with it.
 To cancel the registration, select “Cancel”.
6
Register the Bluetooth® device using
your Bluetooth® device.
 A PIN-code is not required for SSP
(Secure Simple Pairing) compatible
Bluetooth® devices. Depending on the
type of Bluetooth® device being connected, a message confirming registration may be displayed on the Bluetooth®
device’s screen. Respond and operate the
Bluetooth® device according to the confirmation message.
2. Bluetooth® SETTINGS
7
Check that the screen is displayed
when registration is complete.
 The system waits for connection requests
coming from the registered device.
 At this stage, the Bluetooth® functions are
not yet available.
Turn the Bluetooth® connection setting
of your audio player on.
 This function is not available when the
Bluetooth® connection setting of your
audio player is set to off.
2
Press the “AUDIO” button.
3
Select “Source” on the audio screen
or press “AUDIO” button again.
4
5
Select “
6
Follow the steps in “REGISTERING A
Select “OK” when the connection status changes from “Connection waiting...” to “Connected”.
 If an error message is displayed, follow
the guidance on the screen to try again.
REGISTERING A Bluetooth®
AUDIO PLAYER FOR THE
FIRST TIME
To use the Bluetooth® Audio, it is necessary to register an audio player with
the system.
Audio”.
Select “Yes” to register an audio player.
Bluetooth® DEVICE” from “STEP 2”.
(P.45)
Once the player has been registered, it
is possible to use the Bluetooth® Audio.
This operation cannot be performed
while driving.
For details about registering
Bluetooth® device: P.45
2
BASIC FUNCTION
8
1
a
41
2. Bluetooth® SETTINGS
PROFILES
This system supports the following services.
Bluetooth®
Device
Bluetooth®
Phone/
Bluetooth®
Audio
Player
Spec.
Bluetooth® Specification
Bluetooth®
Device
Profile
HFP (Hands-Free Profile)
Function
Registering
a
Bluetooth®
vice
de-
Function
Hands-free
system
OPP (Object Push Profile)
Bluetooth
Phone
®
Bluetooth®
Audio
Player
PBAP (Phone Book Access profile)
Transferring the
contacts
Requirements
Recommendations
Ver. 2.0
Ver. 3.0
+EDR
Requirements
Recommendations
Ver. 1.0
Ver. 1.6
Ver. 1.1
Ver. 1.2
Ver. 1.0
Ver. 1.1
MAP (Message Access
Profile)
Bluetooth®
phone message

Ver. 1.0
SPP (Serial Port Profile)
Entune App Suite

Ver. 1.1
Ver. 1.0
Ver. 1.2
Ver. 1.0
Ver. 1.4
A2DP (Advanced Audio
Distribution Profile)
AVRCP (Audio/Video Remote Control Profile)
Bluetooth® audio
system
INFORMATION
● If your cellular phone does not support HFP, registering the Bluetooth® phone or using
OPP, PBAP, MAP or SPP profiles individually will not be possible.
● If the connected Bluetooth® device version is older than recommended or incompatible,
the Bluetooth® device function may not work properly.
● Refer to http://www.toyota.com/entune/ to find approved Bluetooth® phones for this system.
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
42
2. Bluetooth® SETTINGS
CERTIFICATION
U.S.A.
 IC: 2024B-FT0044C
 This device complies with Industry
Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2)this
device must accept any interference,
including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux
CNR d'Industrie Canada applicables
aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux
conditions suivantes: (1)l'appareil ne
doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi,
même si le brouillage est susceptible
d'en compromettre le fonctionnement.
 CAUTION: Radio Frequency Radiation
Exposure
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment and meets
RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment should
be installed and operated keeping the
radiator at least 20cm or more away
from person’s body (excluding extremities: hands, wrists, feet and ankles).
ATTENTION: l'exposition aux rayonnements radiofréquence
Cet équipement est conforme aux limites d'exposition de rayonnement IC établies pour un environnement non
contrôlé et remplit les conditions RSS102 en matière d'exposition aux
radiofréquences (RF) IC. Cet équipement doit être installé et utilisé en maintenant une distance d'au moins 20 cm
ou plus entre le radiateur et le corps
d'une personne (à l'exception des extrémités: mains, poignets, pieds et chevilles).
43
2
BASIC FUNCTION
 FCC ID: BABFT0044C
 This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference,
and (2) this device must accept any
interference
received,
including
interference that may cause undesired
operation.
 FCC
WARNING:
Changes
or
modifications not expressly approved by
the party responsible for compliance
could void the user’s authority to
operate the equipment.
 CAUTION: Radio Frequency Radiation
Exposure
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment and meets the
FCC radio frequency (RF) Exposure
Guidelines. This equipment should be
installed and operated keeping the
radiator at least 20cm or more away
from person’s body in normal use
position.
 Co-location: This transmitter must not
be co-located or operated in conjunction
with any other antenna or transmitter.
Canada
2. Bluetooth® SETTINGS
2. SETTING Bluetooth® DETAILS
1
Press the “APPS” button.
2
3
4
Select “Setup”.
“Bluetooth* Setup” SCREEN
Function
Registering a
Select “Bluetooth*”.
Select the desired item to be set.
Page
Bluetooth®
device
45
Deleting a Bluetooth® device
46
Connecting a Bluetooth® device
47
Editing the
mation
Bluetooth®
device infor-
Bluetooth® system settings
49
50
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
44
2. Bluetooth® SETTINGS
DISPLAYING THE “Bluetooth*
Setup” SCREEN IN A
DIFFERENT WAY
1
2
3
4
phone/message
settings
Press the “APPS” button.
Select “Setup”.
Select “Phone”.
Select “Connect Phone”.
From the status display
1
Select status display area on the
screen.
Up to 5 Bluetooth® devices can be registered.
2
Bluetooth® compatible phones (HFP)
and audio players (AVP) can be registered simultaneously.
BASIC FUNCTION
From the
screen
REGISTERING A Bluetooth®
DEVICE
This operation cannot be performed
while driving.
1
Display the “Bluetooth* Setup” screen.
(P.44)
2
Select “Add”.
When another Bluetooth® device is connected
 To disconnect the Bluetooth® device,
select “Yes”.
When 5 Bluetooth® devices have already been registered
 A registered device needs to be replaced.
Select “Yes”, and select the device to be
replaced.
3
When this screen is displayed, search
for the device name displayed on this
screen on the screen of your
Bluetooth® device.
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
45
2. Bluetooth® SETTINGS
 For details about operating the Bluetooth®
device, see the manual that comes with it.
 To cancel the registration, select “Cancel”.
4
Register the Bluetooth® device using
your Bluetooth® device.
 A PIN-code is not required for SSP
(Secure Simple Pairing) compatible
Bluetooth® devices. Depending on the
type of Bluetooth® device being connected, a message confirming registration may be displayed on the Bluetooth®
device’s screen. Respond and operate the
Bluetooth® device according to the confirmation message.
5
Check that the screen is displayed
when registration is complete.
 The system waits for connection requests
coming from the registered device.
 At this stage, the Bluetooth® functions are
not yet available.
6
Select “OK” when the connection status changes from “Connection waiting...” to “Connected”.
DELETING A Bluetooth®
DEVICE
1
Display the “Bluetooth* Setup” screen.
(P.44)
2
3
Select “Remove”.
4
Select “Yes” when the confirmation
screen appears.
5
Check that a confirmation screen is
displayed when the operation is complete.
Select the desired device.
INFORMATION
● When deleting a Bluetooth® phone, the
contact data will be deleted at the same
time.
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
 If an error message is displayed, follow
the guidance on the screen to try again.
46
2. Bluetooth® SETTINGS
CONNECTING A Bluetooth®
DEVICE
®
If more than 1 Bluetooth device has
been registered, select which device to
connect to.
1
2
Display the “Bluetooth* Setup” screen.
(P.44)
Select the device to be connected.
Select the desired connection.
When another Bluetooth® device is connected
 To disconnect the Bluetooth® device,
select “Yes”.
4
Check that a confirmation screen is
displayed when the connection is complete.
 If an error message is displayed, follow
the guidance on the screen to try again.
INFORMATION
● It may take time if the device connection
is carried out during Bluetooth® audio
playback.
● Depending on the type of Bluetooth®
device being connected, it may be necessary to perform additional steps on
the device.
● When disconnecting a Bluetooth®
device, it is recommended to disconnect
using the navigation system.
 Supported profile icons will be displayed.
: Phone
: Audio player
: Phone/Entune App Suite service
 The profile icon for a currently connected
device will be displayed in color.
 Selecting a profile icon which is not currently connected will switch the connection to the function.
 If the desired Bluetooth® device is not
on the list, select “Add” to register the
device. (P.45)
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
47
2
BASIC FUNCTION
Up to 5 Bluetooth® devices (Phones
(HFP) and audio players (AVP)) can be
registered.
3
2. Bluetooth® SETTINGS
■AUTO CONNECTION MODE
To turn auto connection mode on, set
“Bluetooth* Power” to on. (P.50)
Leave the Bluetooth® device in a location where the connection can be established.
 When the power switch is turned to
ACCESSORY or ON mode, the system
searches for a nearby registered device.
 The system will connect with the registered device that was last connected, if it
is nearby.
■CONNECTING MANUALLY
When the auto connection has failed or
“Bluetooth* Power” is turned off, it is
necessary to connect Bluetooth® manually.
1
Press the “APPS” button and select
“Setup”.
2
3
Select “Bluetooth*”.
Follow the steps in “CONNECTING A
Bluetooth® DEVICE” from “STEP 2”.
(P.47)
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
48
■RECONNECTING THE Bluetooth®
PHONE
If a Bluetooth® phone is disconnected
due to poor reception from the
Bluetooth® network when the power
switch is in ACCESSORY or ON mode,
the system automatically reconnects
the Bluetooth® phone.
2. Bluetooth® SETTINGS
EDITING THE Bluetooth®
DEVICE INFORMATION
Information
The name of the Bluetooth® device.
Can be changed to a desired name.
(P.50)
Select to set the Bluetooth® audio
player connection method. (P.50)
1
Display the “Bluetooth* Setup” screen.
(P.44)
Device address is unique to the device and cannot be changed.
2
3
Select the desired device to be edited.
Phone number of the Bluetooth®
phone.
Select “Device Info”.
Compatibility
profile
Bluetooth® device.
of
the
Select to reset all setup items.
INFORMATION
4
Confirm and change the Bluetooth®
device information.
● If 2 Bluetooth® devices have been registered with the same device name, the
devices can be distinguished referring to
the device’s address.
● Depending on the type of phone, some
information may not be displayed.
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
49
2
BASIC FUNCTION
The Bluetooth® device’s information
can be displayed on the screen. The
displayed information can be edited.
No.
2. Bluetooth® SETTINGS
CHANGING A DEVICE NAME
1
2
Select “Device Name”.
Enter the name and select “OK”.
INFORMATION
● Even if the device name is changed, the
name registered in your Bluetooth®
device does not change.
“System Settings” SCREEN
The Bluetooth® settings can be confirmed and changed.
1
Display the “Bluetooth* Setup” screen.
(P.44)
2
3
Select “System Settings”.
Select the desired item to be set.
SETTING AUDIO PLAYER
CONNECTION METHOD
1
Select “Connect
From”.
2
Select the desired connection method.
Audio
Player
“Vehicle”: Select to connect the audio
system to the audio player.
“Device”: Select to connect the audio
player to the audio system.
 Depending on the audio player, the “Vehicle” or “Device” connection method may
be best. As such, refer to the manual that
comes with the audio player.
 To reset the connection method, select
“Default”.
50
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
2. Bluetooth® SETTINGS
No.
Information
Page
Select to set Bluetooth®
connection on/off.
51
51
PIN-code used when the
Bluetooth® device was registered. Can be changed to
a desired code.
51
Device address is unique
to the device and cannot be
changed.

Select to set the phone
connection status display
on/off.

Select to set the connection status display of the
audio player on/off.

Compatibility profile of the
system device.

Select to reset all setup
items.
1
Select “Bluetooth* Power”.
2
When “Bluetooth* Power” is on:
The Bluetooth® device is automatically
connected when the power switch is
turned to ACCESSORY or ON mode.
When “Bluetooth* Power” is off:
The Bluetooth® device is disconnected,
and the system will not connect to it next
time.
INFORMATION
● While driving, the auto connection state
can be changed from off to on, but cannot be changed from on to off.
EDITING THE Bluetooth* NAME
1
2
Select “Bluetooth* Name”.
Enter a name and select “OK”.

EDITING THE PIN-CODE
1
2
Select “Bluetooth* PIN”.
Enter a PIN-code and select “OK”.
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
51
BASIC FUNCTION
Displays system name.
Can be changed to a desired name.
CHANGING “Bluetooth*
Power”
3. OTHER SETTINGS
1. GENERAL SETTINGS
Settings are available for system time,
operation sounds, etc.
1
Press the “APPS” button.
2
3
4
Select “Setup”.
52
Select “General”.
Select the items to be set.
GENERAL SETTINGS
SCREEN
3. OTHER SETTINGS
No.
Function
Function
Select to set the animations on/off.
Select to customize the startup image. (P.55)
2
Select to customize the screen off
image. (P.56)
BASIC FUNCTION
Select to change the time zone and
set the daylight saving time on/off.
(P.54)
No.
Select to change the language.
Select to change the unit of measure
for distance.
Select to change the unit of temperature.
Select to set the sound beeps on/off.
Select to change the screen button
color.
Select to change the keyboard layout.
Select to set automatic screen
changes from the audio control
screen to the home screen to on/off.
When set to on, the screen will automatically return to the home screen
from the audio control screen after
20 seconds.
Select to delete personal data.
(P.57)
Select to update software versions.
For details, contact your Toyota
dealer.
Select to update “Gracenote” database versions. For details, contact
your Toyota dealer.
Select to display the software information. Notices related to third party
software used in this product are enlisted. (This includes instructions for
obtaining such software, where applicable.)
Select to reset all setup items.
53
3. OTHER SETTINGS
SYSTEM TIME SETTINGS
Used for changing time zones and the
on/off settings of daylight saving time.
1
Display the “General Settings” screen.
(P.52)
2
3
Select “System Time”.
Select the items to be set.
No.
Function
Select to change the time zone.
(P.54)
Select to set daylight saving time on/
off.
4
54
Select “OK”.
■SETTING THE TIME ZONE
1
2
Select “Time Zone”.
Select the desired time zone.
3. OTHER SETTINGS
CUSTOMIZING THE STARTUP
AND SCREEN OFF IMAGES
■TRANSFERRING IMAGES
1
An image can be copied from a USB
memory and used as the startup and
screen off images.
Open the cover and connect a USB
memory.
2
BASIC FUNCTION
When the power switch is turned to
ACCESSORY or ON mode, the initial
screen will be displayed. (P.30)
When “Screen Off” on the “Setup”
screen is selected, the screen is turned
off and the desired screen off image
that is set is displayed. (To turn the
screen off: P.18)
 Turn on the power of the USB memory if it
is not turned on.
2
3
4
5
6
7
Press the “APPS” button.
Select “Setup”.
Select “General”.
Select “Customize Startup Image” or
“Customize Screen Off Image”.
Select “Transfer”.
Select “Yes”.
INFORMATION
● When saving the images to a USB,
name the folder that the startup image is
saved to “StartupImage” and name the
folder that the screen off image is saved
to “DisplayOffImage”. If these folder
names are not used, the system cannot
download the images. (The folder
names are case sensitive.)
● The compatible file extensions are JPG
and JPEG.
● Image files of 5 MB or less can be transferred.
● Up to 3 images can be downloaded.
● Files with non-ASCII filenames can not
be downloaded.
55
3. OTHER SETTINGS
■SETTING THE STARTUP IMAGES
1
2
3
4
Display the “General Settings” screen.
(P.52)
ES
1
Display the “General Settings” screen.
(P.52)
2
Select “Customize Startup Image” or
“Customize Screen Off Image”.
3
Select “Delete All”.
4
Select “Yes”.
Select “Customize Startup Image”.
Select the desired image.
Select “OK”.
■SETTINGS THE SCREEN OFF IMAGES
1
Display the “General Settings” screen.
(P.52)
2
Select “Customize Screen Off Image”.
3
Select the desired image.
4
Select “OK”.
56
■DELETING TRANSFERRED IMAG-
3. OTHER SETTINGS
DELETING PERSONAL DATA
1
Display the “General Settings” screen.
(P.52)
2
3
Select “Delete Personal Data”.
4
Select “Yes” when the confirmation
screen appears.
2
BASIC FUNCTION
Select “Delete”.
 Registered or changed personal settings
will be deleted or returned to their default
conditions.
For example:
• General settings
• Navigation settings
• Audio settings
• Phone settings
NOTICE
● Make sure the micro SD card is inserted
when deleting personal data. The personal data cannot be deleted when the
micro SD card is removed. To delete the
data, after inserting the micro SD card,
turn the power switch to ACCESSORY
or ON mode.
57
3. OTHER SETTINGS
2. VOICE SETTINGS
Voice volume, etc. can be set.
1
Press the “APPS” button.
2
3
4
Select “Setup”.
VOICE SETTINGS SCREEN
Select “Voice”.
Select the items to be set.
INFORMATION
● “Voice Settings” screen can also be displayed from the voice recognition top
screen. (P.128)
No.
Function
Select to adjust the volume of voice
guidance.
Select to set the voice guidance during route guidance on/off.
Select to set the voice recognition
prompts.
Select to train voice recognition.
The voice command system adapt
the user accent.
Select to set the voice prompt interrupt on/off.
Select to set the web search engine.
The search engines are Entune App
Suite applications. (P.261)
Select to set the voice recognition
tutorial.
Select to reset all setup items.
58
3. OTHER SETTINGS
3. VEHICLE SETTINGS
Setting is available for vehicle customization.
1
Press the “APPS” button.
2
BASIC FUNCTION
2
3
4
Select “Setup”.
Select “Vehicle”.
Select the desired item to be set.
 For details, refer to “Owner’s Manual”.
59
3. OTHER SETTINGS
4. DRIVER SETTINGS
The driver settings feature will allow
the system to link some preferences
(such as audio presets, button colors,
language, etc.) to a paired Bluetooth®
phone.
1
Press the “APPS” button.
2
3
4
Select “Setup”.
60
Select “Driver”.
Select “Enable this Feature”.
MANUALLY SELECT LINKED
SETTINGS
1
Display the driver settings screen.
(P.60)
2
Select “Manually Select Linked Settings”.
3
Select the desired phone.
 After a few seconds, loaded screen automatically switches to the home screen.
3. OTHER SETTINGS
5. MAINTENANCE
When this system is turned on, the
“Maintenance Reminder” screen displays when it is time to replace a part
or certain components. (P.30)
1
Press the “APPS” button.
No.
Function
Select to set the condition of parts or
components.
Select to add new information items
separately from provided ones.
Select to reset the item which have
expired conditions.
Select to call the registered dealer.
Select to register/edit dealer information. (P.62)
2
3
Select “Maintenance”.
Select the desired item.
When set to on, the indicator will illuminate. The system is set to give
maintenance information with the
“Maintenance Reminder” screen.
(P.30)
INFORMATION
● When the vehicle needs to be serviced,
the screen button color will change to
orange.
61
BASIC FUNCTION
Select to cancel all conditions which
have been entered.
2
3. OTHER SETTINGS
MAINTENANCE INFORMATION
SETTING
1
Select the desired part or component
screen button.
 When the vehicle needs to be serviced,
the screen button color will change to
orange.
2
Set the conditions.
No.
Function
Select to enter the next maintenance
date.
Select to enter the driving distance
until the next maintenance check.
Select to cancel the conditions which
have been entered.
Select to reset the conditions which
have expired.
3
Select “OK” after entering the conditions.
INFORMATION
● For scheduled maintenance information,
refer to “Scheduled Maintenance Guide”
or “Owner’s Manual Supplement”.
● Depending on driving or road conditions,
the actual date and distance that maintenance should be performed may differ
from the stored date and distance in the
system.
62
DEALER SETTING
Dealer information can be registered in
the system. With dealer information
registered, route guidance to the dealer is available.
1
2
Select “Set Dealer”.
Select the desired item to search for
the location. (P.204)
 The editing dealer screen appears after
setting the location.
3. OTHER SETTINGS
3
■EDITING DEALER OR CONTACT
Select the items to be edited.
NAME
1
2
Select “Edit” next to “Dealer” or “Contact”.
Enter the name and select “OK”.
Function
Page
Select to enter the name of
a dealer.
63
Select to enter the name of
a dealer member.
63
Select to set the location.
63
Select to enter the phone
number.
63
Select to delete the dealer
information displayed on
the screen.

Select to set the displayed
dealer as a destination.
216
1
2
Select “Edit” next to “Location”.
Scroll the map to the desired point
(P.196) and select “OK”.
■EDITING PHONE NUMBER
1
2
Select “Edit” next to “Phone #”.
Enter the phone number and select
“OK”.
63
BASIC FUNCTION
■EDITING THE LOCATION
No.
2
3
AUDIO SYSTEM
1
BASIC OPERATION
1. QUICK REFERENCE ..................... 66
2. SOME BASICS............................... 67
TURNING THE SYSTEM
ON AND OFF ...................................... 67
SELECTING AN AUDIO SOURCE........ 68
DISC SLOT ............................................ 69
USB/AUX PORT .................................... 69
SOUND SETTINGS ............................... 70
VOICE COMMAND SYSTEM ................ 71
2
RADIO OPERATION
1. AM/FM RADIO............................... 72
OVERVIEW ............................................ 72
PRESETTING A STATION .................... 75
SELECTING A STATION FROM
THE LIST ............................................. 75
CACHING A RADIO PROGRAM ........... 76
RADIO BROADCAST DATA
SYSTEM .............................................. 77
TRAFFIC ANNOUNCEMENT
(FM RADIO)......................................... 78
USING HD Radio™ TECHNOLOGY...... 78
AVAILABLE HD Radio™
TECHNOLOGY.................................... 79
TROUBLESHOOTING GUIDE............... 81
2. XM Satellite Radio ........................ 82
OVERVIEW ............................................ 82
HOW TO SUBSCRIBE TO
AN XM Satellite Radio ......................... 85
DISPLAYING THE RADIO ID................. 87
PRESETTING A CHANNEL................... 87
SELECTING A CHANNEL FROM
THE LIST ............................................. 87
IF THE SATELLITE RADIO TUNER
MALFUNCTIONS ................................ 88
3. INTERNET RADIO......................... 89
LISTENING TO INTERNET RADIO ....... 89
64
3
1
AUDIO SYSTEM
2
3
MEDIA OPERATION
1. CD .................................................. 90
4
AUDIO REMOTE CONTROLS
3
1. STEERING SWITCHES............... 112
4
OVERVIEW ........................................... 90
PLAYING AN AUDIO CD ...................... 93
5
SETUP
PLAYING AN MP3/WMA/AAC DISC ..... 93
2. USB MEMORY............................... 94
5
1. AUDIO SETTINGS ...................... 114
AUDIO SETTINGS SCREEN............... 114
OVERVIEW ........................................... 94
6
PLAYING A USB AUDIO ....................... 98
3. iPod................................................ 99
OVERVIEW ........................................... 99
iPod AUDIO ......................................... 103
iPod VIDEO ......................................... 103
4.
Bluetooth®
6
TIPS FOR OPERATING
THE AUDIO SYSTEM
7
1. OPERATING INFORMATION ..... 116
RADIO.................................................. 116
AUDIO ...................... 104
CD PLAYER AND DISC ...................... 117
OVERVIEW ......................................... 104
iPod...................................................... 119
CONNECTING A Bluetooth®
DEVICE............................................. 108
FILE INFORMATION ........................... 120
LISTENING TO Bluetooth® AUDIO ..... 108
ERROR MESSAGES........................... 124
TERMS ................................................ 123
5. AUX .............................................. 109
OVERVIEW ......................................... 109
65
8
9
1. BASIC OPERATION
1. QUICK REFERENCE
The audio control screen can be reached by the following methods:
Using the “AUDIO” button
Press the “AUDIO” button to display the audio screen.
Using the “APPS” button
Press the “APPS” button, then select “Audio” to display the audio screen.
Function
Using the radio
Page
72, 82, 89
Playing an audio CD or MP3/WMA/AAC disc
90
Playing a USB memory
94
Playing an iPod®
99
®
Playing a Bluetooth device
104
Using the AUX port
109
Using the steering wheel audio switches
112
Audio system settings
114
66
1. BASIC OPERATION
2. SOME BASICS
This section describes some of the basic features of the audio system. Some
information may not pertain to your
system.
TURNING THE SYSTEM ON
AND OFF
Your audio system works when the
power switch is in ACCESSORY or ON
mode.
3
● To prevent the 12-volt battery from being
discharged, do not leave the audio system on longer than necessary when the
hybrid system is off.
CERTIFICATION
CAUTION:
 For vehicles sold in U.S.A.:
Part 15 of the FCC Rules
FCC WARNING: Changes or modifications not expressly approved by the
party responsible for compliance could
void the user’s authority to operate the
equipment.
“PWR·VOL” knob: Press to turn the audio
system on and off. The system turns on in
the last mode used. Turn this knob to adjust the volume.
“AUDIO” button: Press to display screen
buttons for the audio system.
 A function that enables automatic return
to the home screen from the audio
screen can be selected. (P.52)
67
AUDIO SYSTEM
NOTICE
1. BASIC OPERATION
REORDERING THE AUDIO
SOURCE
SELECTING AN AUDIO
SOURCE
1
Press the “AUDIO” button.
2
Select “Source” or press “AUDIO”
button again.
3
Select the desired source.
1
Display the “Select Audio Source”
screen. (P.68)
2
Select “Reorder”.
3
Select the desired audio source then
or
4
INFORMATION
● Dimmed screen buttons cannot be operated.
● When there are two pages, select
or
68
to change the page.
Select “OK”.
to reorder.
1. BASIC OPERATION
DISC SLOT
USB/AUX PORT
INSERTING A DISC
1
1
Open the cover and connect a device.
Insert a disc into the disc slot.
3
 After insertion, the disc is automatically
loaded.
EJECTING A DISC
1
Press the
disc.
button and remove the
INFORMATION
● If a USB hub is plugged-in, two devices
can be connected at a time.
● Even if a USB hub is used to connect
more than two USB devices, only the
first two connected devices will be recognized.
NOTICE
● Never try to disassemble or oil any part
of the CD player. Do not insert anything
other than a disc into the slot.
INFORMATION
● The player is intended for use with 4.7
in. (12 cm) discs only.
● When inserting a disc, gently insert the
disc with the label facing up.
69
AUDIO SYSTEM
 Turn on the power of the device if it is not
turned on.
1. BASIC OPERATION
SOUND SETTINGS
TONE AND BALANCE
TONE:
AUTOMATIC SOUND
LEVELIZER (ASL)
The system adjusts to the optimum volume and tone quality according to vehicle speed to compensate for
increased vehicle noise.
BALANCE:
1
Display the “Audio Settings” screen.
(P.114)
2
3
Select “Automatic Sound Levelizer”.
70
How good an audio program sounds is
largely determined by the mix of the
treble, mid and bass levels. In fact, different kinds of music and vocal programs usually sound better with
different mixes of treble, mid and bass.
Select “High”, “Mid”, “Low”, or
“Off”.
A good balance of the left and right stereo channels and of the front and rear
sound levels is also important.
Keep in mind that when listening to a
stereo recording or broadcast, changing the right/left balance will increase
the volume of 1 group of sounds while
decreasing the volume of another.
1. BASIC OPERATION
1
Select “Sound” on the audio control
screen.
2
Select the desired screen button.
VOICE COMMAND SYSTEM
1
Press this switch to operate the voice
command system.
3
AUDIO SYSTEM
No.
Function
Select “+” or “-” to adjust highpitched tones.
Select “+” or “-” to adjust midpitched tones.
 The voice command system and its list
of commands can be operated.
(P.126)
Select “+” or “-” to adjust lowpitched tones.
Select to adjust the sound balance
between the front and rear speakers.
Select to adjust the sound balance
between the left and right speakers.
71
2. RADIO OPERATION
1. AM/FM RADIO
OVERVIEW
The radio operation screen can be reached by the following methods:
Select “AM” or “FM” on the “Select Audio Source” screen. (P.68)
■CONTROL SCREEN
Top screen
Option screen
72
2. RADIO OPERATION
■CONTROL PANEL
3
AUDIO SYSTEM
73
2. RADIO OPERATION
No.
Function
Select to scroll the page of preset buttons.
Select to display the option screen.
Select to display the audio source selection screen.
Select to display the cache radio operation buttons. (P.76)
Select to display the sound setting screen.
Cache radio only: Select to turn mute on/off.
Select to display a list of receivable stations/channels.
Select to store information of the audio currently being broadcast on the radio.
Select to tune to preset stations/channels.
Select to display the additional text information.
Select to scan for receivable stations/channels.
Select to turn HD Radio mode on/off.
When the “HD Radio™” indicator is off, the station list shows only analog broadcasts.
Analog FM only: Select to display RBDS text messages.
 Turn to step up/down frequencies.
 Turn to move up/down the list. Also, the knob can be used to enter selections on the
list screens by pressing it.
Press to select an audio mode.
 Turn to adjust volume.
 Press to turn the audio system on/off.
 Press and hold to restart the audio system.
 Press to seek for a station/channel.
 Press and hold for continuous seek.
INFORMATION
● The radio automatically changes to stereo reception when a stereo broadcast is received.
● The radio automatically blends to an HD Radio signal in AM or FM where available.
74
2. RADIO OPERATION
PRESETTING A STATION
Radio mode has a mix preset function,
which can store up to 36 stations (6
stations per page x 6 pages) from any
of the AM, FM or SAT bands.
Tune in the desired station.
A station list can be displayed.
1
2
Select “Station List”.
3
Select the desired station and select
“OK”.
FM radio only: Select the desired program genre.
Select “(add new)”.
 To change the preset station to a different
one, select and hold the preset station.
3
Select “Yes” on the confirmation
screen.
4
Select “OK” after setting the new preset station.
3
AUDIO SYSTEM
1
2
SELECTING A STATION
FROM THE LIST
INFORMATION
● The number of preset radio stations displayed on the screen can be changed.
(P.115)
75
2. RADIO OPERATION
■REFRESHING THE STATION LIST
1
Select “Refresh” on the station list
screen and the following screen will be
displayed.
CACHING A RADIO
PROGRAM
A radio program can be cached and
played back in a time-shifted manner.
PLAYING BACK THE CACHE
MANUALLY
The broadcast cached in the program
cache can be played back manually.
“Cancel Refresh”: Select to cancel the
refresh.
“Source”: Select to change to another audio source while refreshing.
1
Display the cache radio operation buttons. (P.72)
2
Select the desired cache radio operation button.
INFORMATION
● The audio system sound is muted during
refresh operation.
● In some situations, it may take some
time to update the station list.
No.
Function
Hides the cache operation buttons
Skips backward 2 minutes
Fast rewinds continuously
Returns to the live radio broadcast
Fast forwards continuously
Skips forward 2 minutes
Shows the current playback location
relative to the cached broadcast recording time with a bar scale.
76
2. RADIO OPERATION
AUTOMATIC PLAYBACK OF
THE CACHE
INFORMATION
● The system can store up to 20 minutes.
Cached data will be erased when the
radio mode or station is changed or
when the audio system is turned off.
● If noise or silence occurs during the
caching process, cache writing will continue, with the noise or silence recorded
as is. In this case, the cached broadcast
will contain the noise or silence when
played back.
1
Select “Station List”.
2
FM radio only: Select a desired genre
of station and select a desired station.
 The genre list is in the following order:
• Classical
• Country
• EasyLis (Easy Listening)
• Inform (Information)
• Jazz
• News
• Oldies
• Other
• Pop Music
• Religion
• Rock
• R&B (Rhythm and Blues)
• Sports
• Talk
• Traffic (Not available when “HD Radio™”
indicator is off.)
• Alert (Emergency Alert)
RADIO BROADCAST DATA
SYSTEM
This audio system is equipped with Radio Broadcast Data Systems (RBDS).
RBDS mode allows text messages to
be received from radio stations that utilize RBDS transmitters.
When RBDS is on, the radio can
— only select stations of a particular
program type,
— display messages from radio stations,
— search for a stronger signal station.
RBDS features are available only
when listening to an FM station that
broadcasts RBDS information and the
“FM Info” indicator is on.
77
3
AUDIO SYSTEM
If the radio broadcast is interrupted by
another audio output, such as an
incoming phone call, the system will
automatically cache the interrupted
portion
and
perform
time-shift
playback when the interruption ends.
To manually operate the cache
operation: (P.76)
SELECTING A DESIRED
GENRE
2. RADIO OPERATION
TRAFFIC ANNOUNCEMENT
(FM RADIO)
A station that regularly broadcasts traffic information is automatically located.
1
2
Select “Station List”.
Select the desired traffic program station.
INFORMATION
● If a traffic program station is found, the
name of the traffic program station will
be displayed for a while.
USING HD Radio™
TECHNOLOGY
HD Radio™ Technology is the digital
evolution of analog AM/FM radio. Your
radio product has a special receiver
which allows it to receive digital
broadcasts (where available) in
addition to the analog broadcasts it
already receives. Digital broadcasts
have better sound quality than analog
broadcasts as digital broadcasts
provide free, crystal clear audio with no
static or distortion. For more
information, and a guide to available
radio stations and programming, refer
to www.hdradio.com.
HD Radio Technology manufactured
under license from iBiquity Digital
Corporation. U.S. and
Foreign
Patents. HD Radio™ and the HD, HD
Radio, and “Arc” logos are proprietary
trademarks of iBiquity Digital Corp.
78
2. RADIO OPERATION
AVAILABLE HD Radio™
TECHNOLOGY
MULTICAST
On the FM radio frequency most digital
stations have “multiple” or supplemental programs on one FM station.
2
Tag information in the music broadcasting is preserved in the system and
transmits to an iPod.
1
Select “Tag” to bookmark the music
information.
2
Connect an iPod. (P.69)
Select the “HD)” logo.
Select the desired channel.
 Turning the “TUNESCROLL” knob can
also select the desired multicast channel.
3
AUDIO SYSTEM
1
PRESERVING A MUSIC
INFORMATION
 Turn on the power of the iPod if it is not
turned on.
 Once an iPod is connected, the music tag
moves from the radio into the iPod.
 When the iPod is connected to iTunes, the
“tagged” information of the songs which
were tagged while listening to the radio
can be viewed. Then a user may decide to
purchase the song or CD/Album which
had been listened to on their radio.
79
2. RADIO OPERATION
INFORMATION
● The tag information can not be preserved while scanning or caching the
radio station.
● If tagging the music information fails,
“Saving the HD Radio tag was unsuccessful.” will be displayed on the screen.
If this occurs, tag the information again.
● HD Radio™ stations can be preset.
● An orange “HD)” logo indicator will be
displayed on the screen when in digital.
The “HD)” logo will first appear in a gray
color indicating the station is indeed (an
analog and) a digital station. Once the
digital signal is acquired, the logo will
change to a bright orange color.
● The song title and artist name will
appear on the screen when available by
the radio station. The radio station can
send album pictures when available.
● As a user works through the analog
radio stations, (where applicable) the
radio receiver will automatically tune
from an analog signal to a digital signal
within 5 seconds.
80
2. RADIO OPERATION
TROUBLESHOOTING GUIDE
Cause
Action
Mismatch of time alignment- a user may hear a
short period of programming replayed or an echo,
stutter or skip.
The radio stations analog
and digital volume is not
properly aligned or the station is in ballgame mode.
None, radio broadcast issue. A
user can contact the radio station.
Sound fades, blending in
and out.
Radio is shifting between
analog and digital audio.
Reception issue, may clear-up as
the vehicle continues to be driven.
Turning the indicator of the “HD
Radio™” button off can force radio
in an analog audio.
Audio mute condition when
an HD2/HD3 multicast
channel had been playing.
The radio does not have
access to digital signals at
the moment.
This is normal behavior, wait until
the digital signal returns. If out of
the coverage area, seek a new
station.
Audio mute delay when selecting an HD2/HD3 multicast channel preset.
The digital multicast content is not available until
HD Radio™ broadcast can
be decoded and make the
audio available. This takes
up to 7 seconds.
This is normal behavior, wait for
the audio to become available.
Text information does not
match the present song audio.
Data service issue by the
radio broadcaster.
Broadcaster should be notified.
Complete the form;
www.ibiquity.com/automotive/
report_radio_station_experiences.
No text information shown
for the present selected frequency.
Data service issue by the
radio broadcaster.
Broadcaster should be notified.
Complete the form;
www.ibiquity.com/automotive/
report_radio_station_experiences.
81
3
AUDIO SYSTEM
Experience
2. RADIO OPERATION
2. XM Satellite Radio
OVERVIEW
The satellite radio operation screen can be reached by the following methods:
Select “XM” on the “Select Audio Source” screen. (P.68)
■CONTROL SCREEN
82
2. RADIO OPERATION
■CONTROL PANEL
3
AUDIO SYSTEM
83
2. RADIO OPERATION
No.
Function
Select to scroll the page of preset buttons.
Select to display the option screen.
 Select to scan for receivable channels.
 Select “Additional Information” to display the information.
Select to display the audio source selection screen.
Select to display the sound setting screen.
Select to display a list of receivable channels.
Select to tune to preset channels.
 Turn to step up/down channels.
 Turn to move up/down the list. Also, the knob can be used to enter selections on the
list screens by pressing it.
Press to select an audio mode.
 Turn to adjust volume.
 Press to turn the audio system on/off.
 Press and hold to restart the audio system.
 Press to seek for a channel.
 Press and hold for continuous seek.
CERTIFICATION
CAUTION:
 FCC WARNING: Changes or modifications in construction not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment.
 Radio frequency exposure.
This device is approved for Mobile Application only and, to comply with applicable FCC
radio frequency exposure regulations, must be used with a distance of at least 7.9 in.
(20cm) between the antenna and the body of any person at all time during use.
NOTICE:
 THIS DEVICE COMPLIES WITH PART15 OF THE FCC RULES.
 OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS,
1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
84
2. RADIO OPERATION
HOW TO SUBSCRIBE TO AN
XM Satellite Radio
To listen to a satellite radio broadcast
in the vehicle, a subscription to the XM
Satellite Radio service is necessary.
HOW TO SUBSCRIBE
It is necessary to enter into a separate
service agreement with XM Satellite
Radio in order to receive satellite
broadcast programming in the vehicle.
Additional activation and service subscription fees apply that are not included in the purchase price of the vehicle
and digital satellite tuner.
 For complete information on subscription rates and terms, or to subscribe to
XM Satellite Radio:
 U.S.A.
Refer to www.siriusxm.com or call
1-866-635-2349.
Canada
Refer to www.xmradio.ca or call
1-877-438-9677.
● XM Radio ServicesLegal Disclaimers
and Warnings
• Fees and TaxesSubscription fee,
taxes, one time activation fee, and
other fees may apply. Subscription fee
is consumer only. All fees and programming subject to change.
Subscriptions subject to Customer
Agreement available at www.siriusxm.com. (U.S.A.) or www.xmradio.ca (Canada) XM service only
available in the 48 contiguous United
States and Canada.
Explicit Language NoticeChannels
with frequent explicit language are indicated with an “XL” preceding the channel name. Channel blocking is
available for XM Satellite Radio receivers by notifying XM at;
U.S.A. Customers:
Visit www.siriusxm.com or calling
1-866-635-2349
Canadian Customers:
Visit www.xmradio.ca or calling
1-877-438-9677
● It is prohibited to copy, decompile, disassemble, reverse engineer, hack, manipulate, or otherwise make available any
technology or software incorporated in
receivers compatible with the XM Satellite Radio System or that support the XM
website, the Online Service or any of its
content. Furthermore, the AMBE® voice
compression software included in this
product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice
Systems, Inc.
● Note: this applies to XM receivers only
and not XM Ready devices.
85
3
AUDIO SYSTEM
An XM Satellite Radio is a tuner designed exclusively to receive broadcasts provided under a separate
subscription. Availability is limited to
the 48 contiguous U.S. states and
some Canadian provinces.
NOTICE
2. RADIO OPERATION
INFORMATION
● XM Radio ServicesDescriptions
• Radio and Entertainment
XM offers more than 170 satellite radio
channels of commercial-free music
and premier sports, news, talk, and
entertainment. XM is broadcast via satellites to millions of listeners across the
continental United States. XM subscribers listen to XM on satellite radio
receivers for the car, home, and portable use. More information about XM is
available online at www.siriusxm.com
(U.S.A.) or www.xmradio.ca (Canada).
● XM
Radio
ServicesSubscription
Instructions
• For XM Services requiring a subscription (such as XM Radio, and some
Infotainment & data services), the following paragraph shall be included.
Required XM Radio and some Infotainment & data services monthly subscriptions sold separately after trial
period. Subscription fee is consumer
only. All fees and programming subject
to change. Subscriptions are subject to
the Customer Agreement available at
www.siriusxm.com. XM service only
available in the 48 contiguous United
States.  2011 Sirius XM Radio Inc.
Sirius, XM and all related marks and
logos are trademarks of Sirius XM
Radio Inc. All other marks, channel
names and logos are the property of
their respective owners.
For more information, program schedules, and to subscribe or extend subscription after complimentary trial
period; more information is available
at:
USA Customers:
Visit www.siriusxm.com or call
1-866-635-2349
Canadian Customers:
Visit www.xmradio.ca or call
1-877-438-9677
86
INFORMATION
● XM Satellite Radio is solely responsible
for the quality, availability and content of
the satellite radio services provided,
which are subject to the terms and conditions of the XM Satellite Radio customer service agreement.
● Customers should have their radio ID
ready; the radio ID can be found by tuning to “Ch 000” on the radio. For details,
see “DISPLAYING THE RADIO ID”
below.
● All fees and programming are the
responsibility of XM Satellite Radio and
are subject to change.
SATELLITE TUNER
TECHNOLOGY NOTICE
Toyota’s satellite radio tuners are
awarded Type Approval Certificates
from XM Satellite Radio Inc. as proof of
compatibility with the services offered
by XM Satellite Radio.
INFORMATION
● Satellite tuner
The tuner supports only Audio Services
(Music and Talk) and the accompanying
Text Information of XM® Satellite Radio.
2. RADIO OPERATION
DISPLAYING THE RADIO ID
Each XM tuner is identified with a
unique radio ID. The radio ID is required when activating an XM service
or when reporting a problem.
1
2
3
Select “Channel List”.
Select the desired program genre.
Select the desired channel and select
“OK”.
PRESETTING A CHANNEL
1
2
Tune in the desired channel.
Select “(add new)”.
 To change the preset channel to a different one, select and hold the preset station/
channel.
3
Select “Yes” on the confirmation
screen.
4
Select “OK” after setting the new preset channel.
3
AUDIO SYSTEM
 If “Ch 000” is selected using the
“TUNESCROLL” knob, the ID code,
which is 8 alphanumeric characters, will
be displayed. If another channel is
selected, the ID code will no longer be displayed. The channel (000) alternates
between displaying the radio ID and the
specific radio code.
SELECTING A CHANNEL
FROM THE LIST
87
2. RADIO OPERATION
IF THE SATELLITE RADIO TUNER MALFUNCTIONS
When problems occur with the XM tuner, a message will appear on the screen. Referring to the table below to identify the problem, take the suggested corrective action.
Message
Explanation
The XM antenna is not connected. Check whether the XM antenna
cable is attached securely.
“Check Antenna”
A short circuit occurs in the antenna or the surrounding antenna cable. See a Toyota certified dealer for assistance.
You have not subscribed to XM Satellite Radio. The radio is being
updated with the latest encryption code. Contact XM Satellite Radio
for subscription information. When a contract is canceled, you can
choose “Ch 000” and all free-to-air channels.
“Ch Unauthorized”
The premium channel you selected is not authorized. Wait for about
2 seconds until the radio returns to the previous channel or “Ch 001”.
If it does not change automatically, select another channel. To listen
to the premium channel, contact XM Satellite Radio.
“No Signal”
The XM signal is too weak at the current location. Wait until your vehicle reaches a location with a stronger signal.
“Loading”
The unit is acquiring audio or program information. Wait until the unit
has received the information.
“Channel Off Air”
The channel you selected is not broadcasting any programming. Select another channel.
-----
There is no song/program title or artist name/feature associated with
the channel at that time. No action is required.
“Chan Unavailable”
The channel you selected is no longer available. Wait for about 2
seconds until the radio returns to the previous channel or “Ch 001”.
If it does not change automatically, select another channel.
INFORMATION
● Contact the XM Listener Care Center at 1-866-635-2349 (U.S.A.) or 1-877-438-9677
(Canada).
88
2. RADIO OPERATION
3. INTERNET RADIO
LISTENING TO INTERNET
RADIO
One of Entune App Suite features is
the ability to listen to internet radio. In
order to use this service, a compatible
phone and the system needs to be set
up. For details: P.261
Select the internet radio application.
● Other applications can be activated
while listening to internet radio.
● If an iPhone is connected via Bluetooth®
and USB at the same time, system operation may become unstable. For known
phone compatibility information, refer to
http://www.toyota.com/entune/.
● Some parts of applications can be
adjusted using the switches on the
steering wheel.
● For additional information, refer to
http://www.toyota.com/entune/ or call
1-800-331-4331.
 The internet radio application screen is
displayed.
 Perform operations according to the displayed application screen.
 For the instrument panel operation
method: P.68
 If a compatible phone is already registered, it will be connected automatically.
89
3
AUDIO SYSTEM
1
INFORMATION
3. MEDIA OPERATION
1. CD
OVERVIEW
The CD operation screen can be reached by the following methods:
Select “CD” on the “Select Audio Source” screen. (P.68)
Insert a disc. (P.69)
■CONTROL SCREEN
90
3. MEDIA OPERATION
■CONTROL PANEL
3
AUDIO SYSTEM
91
3. MEDIA OPERATION
No.
Function
 Displays cover art
 Select to display a track/file list.
Select to display the audio source selection screen.
Select to display the sound setting screen.
Select to play/pause.
Shows progress
Select to set repeat playback.
Select to set random playback.
 Audio CD: Select to display a track list.
 MP3/WMA/AAC disc: Select to display a folder list.
To return to the top screen, select “Now Playing” on the list screen.
Disc slot
 Turn to select a track/file.
 Turn to move up/down the list. Also, the knob can be used to enter selections on the
list screens by pressing it.
Press to select an audio mode.
 Turn to adjust volume.
 Press to turn the audio system on/off.
 Press and hold to restart the audio system.
 Press to select a track/file.
 Press and hold to fast forward/rewind.
Press to eject a disc.
INFORMATION
● If a disc contains CD-DA files and MP3/WMA/AAC files, only the CD-DA files can be
played back.
● If a CD-TEXT disc is inserted, the title of the disc and track will be displayed. Up to 32
characters can be displayed.
● If the disc contains no CD-TEXT, only the track number would be displayed on the
screen.
92
3. MEDIA OPERATION
PLAYING AN AUDIO CD
PLAYING AN MP3/WMA/AAC
DISC
REPEATING
The track currently being listened to
can be repeated.
1
The file currently being listened to can
be repeated.
1
Select the repeat button to change on/
off.
RANDOM ORDER
Tracks can be automatically and randomly selected.
1
Select the random button to change
on/off.
RANDOM ORDER
Files can be automatically and randomly selected.
1
Select the random button to change
on/off.
93
3
AUDIO SYSTEM
Select the repeat button to change on/
off.
REPEATING
3. MEDIA OPERATION
2. USB MEMORY
OVERVIEW
The USB memory operation screen can be reached by the following methods:
Select “USB (DEVICE NAME)” on the “Select Audio Source” screen. (P.68)
Connect a USB memory. (P.69)
■CONTROL SCREEN
94
3. MEDIA OPERATION
■CONTROL PANEL
3
AUDIO SYSTEM
95
3. MEDIA OPERATION
No.
Function
Select to display the audio source selection screen.
Select to display the sound setting screen.
Select to play/pause.
Shows progress
Select to set repeat playback.
Select to set random playback.
Select to display the play mode selection screen.
To return to the top screen, select “Now Playing” on the list screen.
 Displays cover art
 Select to display file/track list.
 Turn to select a file/track.
 Turn to move up/down the list. Also, the knob can be used to enter selections on the
list screens by pressing it.
Press to select an audio mode.
 Turn to adjust volume.
 Press to turn the audio system on/off.
 Press and hold to restart the audio system.
 Press to select a file/track.
 Press and hold to fast forward/rewind.
96
3. MEDIA OPERATION
WARNING
● Do not operate the player’s controls or connect the USB memory while driving.
NOTICE
INFORMATION
● If tag information exists, the file names will be changed to track names.
97
3
AUDIO SYSTEM
● Do not leave your portable player in the car. In particular, high temperatures inside the
vehicle may damage the portable player.
● Do not push down on or apply unnecessary pressure to the portable player while it is connected as this may damage the portable player or its terminal.
● Do not insert foreign objects into the port as this may damage the portable player or its
terminal.
3. MEDIA OPERATION
PLAYING A USB AUDIO
REPEATING
The file/track currently being listened
to can be repeated.
1
Select the repeat button to change on/
off.
RANDOM ORDER
Files/tracks can be automatically and
randomly selected.
1
98
Select the random button to change
on/off.
3. MEDIA OPERATION
3. iPod
OVERVIEW
The iPod operation screen can be reached by the following methods:
Select “iPod (DEVICE NAME)” on the “Select Audio Source” screen. (P.68)
Connect an iPod. (P.69)
When the iPod connected to the system includes iPod video, the system can only
output the sound by selecting the browse screen. (P.103)
3
AUDIO SYSTEM
■CONTROL SCREEN
99
3. MEDIA OPERATION
■CONTROL PANEL
100
3. MEDIA OPERATION
No.
Function
 Displays cover art
 Select to display a track list.
Select to display the audio source selection screen.
Select to display the sound setting screen.
3
Select to play/pause.
AUDIO SYSTEM
Shows progress
Select to set repeat playback.
Select to set random playback.
Select to display the play mode selection screen.
To return to the top screen, select “Now Playing” on the list screen.
 Turn to select a track.
 Turn to move up/down the list. Also, the knob can be used to enter selections on the
list screens by pressing it.
Press to select an audio mode.
 Turn to adjust volume.
 Press to turn the audio system on/off.
 Press and hold to restart the audio system.
 Press to select a track.
 Press and hold to fast forward/rewind.
101
3. MEDIA OPERATION
WARNING
● Do not operate the player’s controls or connect the iPod while driving.
NOTICE
● Do not leave your portable player in the car. In particular, high temperatures inside the
vehicle may damage the portable player.
● Do not push down on or apply unnecessary pressure to the portable player while it is connected as this may damage the portable player or its terminal.
● Do not insert foreign objects into the port as this may damage the portable player or its
terminal.
INFORMATION
● The system can only output the sound while driving.
● When an iPod is connected using a genuine iPod cable, the iPod starts charging its battery.
● Depending on the iPod, the video sound may not be able to be heard.
● Depending on the iPod and the songs in the iPod, iPod cover art may be displayed. This
function can be changed to on/off. (P.114) It may take time to display iPod cover art,
and the iPod may not be operated while the cover art display is in process.
● When an iPod is connected and the audio source is changed to iPod mode, the iPod will
resume playing from the same point it was last used.
● Depending on the iPod that is connected to the system, certain functions may not be
available.
● Files/tracks selected by operating a connected iPod may not be recognized or displayed
properly.
● If an iPhone is connected via Bluetooth® and USB at the same time, system operation
may become unstable. For known phone compatibility information, refer to
http://www.toyota.com/entune/.
102
3. MEDIA OPERATION
iPod AUDIO
REPEATING
The track currently being listened to
can be repeated.
1
To change to iPod video mode, select
“Browse” on the iPod audio screen,
then select the “Videos” tab and select the desired video file.
The system can only output the iPod
video sound.
RANDOM ORDER
Tracks can be automatically and randomly selected.
1
3
AUDIO SYSTEM
Select the repeat button to change on/
off.
iPod VIDEO
Select the shuffle button to change on/
off.
103
3. MEDIA OPERATION
4. Bluetooth® AUDIO
The Bluetooth® audio system enables users to enjoy listening to music that is
played on a portable player on the vehicle speakers via wireless communication.
This audio system supports Bluetooth®, a wireless data system capable of playing
portable audio music without cables. If your device does not support Bluetooth®,
the Bluetooth® audio system will not function.
OVERVIEW
The Bluetooth® audio operation screen can be reached by the following methods:
Select “
Audio” on the “Select Audio Source” screen. (P.68)
Connect a Bluetooth® audio device (P.108)
Depending on the type of portable player connected, some functions may not be
available and/or the screen may look differently than shown in this manual.
■CONTROL SCREEN
104
3. MEDIA OPERATION
■CONTROL PANEL
3
AUDIO SYSTEM
105
3. MEDIA OPERATION
No.
Function
Select to display the audio source selection screen.
Displays Bluetooth® device condition.
Select to display the sound settings screen.
Select to play/pause.
Shows progress
Select to set repeat playback.
Select to set random playback.
Select to display the playlist screen.
To return to the top screen, select “Now Playing” on the list screen.
Select to display the portable device connection screen.
 Displays cover art
 Select to display a track list.
 Turn to select a track.
 Turn to move up/down the list. Also, the knob can be used to enter selections on the
list screens by pressing it.
Press to select an audio mode.
 Turn to adjust volume.
 Press to turn the audio system on/off.
 Press and hold to restart the audio system.
 Press to select a track.
 Press and hold to fast forward/rewind.
106
3. MEDIA OPERATION
WARNING
NOTICE
● Do not leave your portable player in the vehicle. In particular, high temperatures inside
the vehicle may damage the portable player.
INFORMATION
● Depending on the Bluetooth® device that is connected to the system, the music may start
playing when selecting
selecting
while it is paused. Conversely, the music may pause when
while it is playing.
● In the following conditions, the system may not function:
• The Bluetooth® device is turned off.
• The Bluetooth® device is not connected.
• The Bluetooth® device has a low battery.
● It may take time to connect the phone when Bluetooth® audio is being played.
● For operating the portable player, see the instruction manual that comes with it.
● If the Bluetooth® device is disconnected due to poor reception from the Bluetooth® network when the power switch is in ACCESSORY or ON mode, the system will automatically reconnect to the portable player.
● If the Bluetooth® device is disconnected on purpose, such as it was turned off, this does
not happen. Reconnect the portable player manually.
● Bluetooth® device information is registered when the Bluetooth® device is connected to
the Bluetooth® audio system. When selling or disposing of the vehicle, remove the
Bluetooth® audio information from the system. (P.57)
107
3
AUDIO SYSTEM
● Do not operate the player’s controls or connect to the Bluetooth® audio system while driving.
● Your audio unit is fitted with Bluetooth® antennas. People with implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter
defibrillators should maintain a reasonable distance between themselves and the
Bluetooth® antennas. The radio waves may affect the operation of such devices.
● Before using Bluetooth® devices, users of any electrical medical device other than
implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or
implantable cardioverter defibrillators should consult the manufacturer of the device for
information about its operation under the influence of radio waves. Radio waves could
have unexpected effects on the operation of such medical devices.
3. MEDIA OPERATION
CONNECTING A Bluetooth®
DEVICE
LISTENING TO Bluetooth®
AUDIO
To use the Bluetooth® audio system, it
is necessary to register a Bluetooth®
device with the system.
Registering an additional device
1
Select
“Select
Device”
on
the
REPEATING
The track currently being listened to
can be repeated.
1
Bluetooth® audio control screen.
2
For more information: P.45
RANDOM ORDER
Selecting a registered device
1
Select
“Select
Device”
on
Bluetooth® audio control screen.
2
108
For more information: P.47
Select the repeat button to change on/
off.
the
Tracks can be automatically and randomly selected.
1
Select the random button to change
on/off.
3. MEDIA OPERATION
5. AUX
OVERVIEW
The AUX operation screen can be reached by the following methods:
Select “AUX” on the “Select Audio Source” screen. (P.68)
Connect a device to the AUX port (P.69)
■CONTROL SCREEN
3
AUDIO SYSTEM
109
3. MEDIA OPERATION
■CONTROL PANEL
110
3. MEDIA OPERATION
No.
Function
Select to display the audio source selection screen.
Select to display the sound setting screen.
Press to select an audio mode.
3
AUDIO SYSTEM
 Turn to adjust volume.
 Press to turn the audio system on/off.
 Press and hold to restart the audio system.
WARNING
● Do not connect portable audio device or operate the controls while driving.
NOTICE
● Do not leave portable audio device in the vehicle. The temperature inside the vehicle may
become high, resulting in damage to the player.
● Do not push down on or apply unnecessary pressure to the portable audio device while it
is connected as this may damage the portable audio device or its terminal.
● Do not insert foreign objects into the port as this may damage the portable audio device
or its terminal.
111
4. AUDIO REMOTE CONTROLS
1. STEERING SWITCHES
Some parts of the audio system can be adjusted using the switches on the steering
wheel.
No.
Switch
“MODE” switch
“ ” switch
Volume control switch
“MODE” switch
Mode
AM,
FM,
XM, AUX
CD,
MP3/
WMA/AAC
disc, USB,
iPod, BT audio, APPS
112
Operation
Function
Press
Change audio modes
Press and hold
(0.8 sec. or more)
Mute
Press
Change audio modes
Press and hold
(0.8 sec. or more)
Pause
4. AUDIO REMOTE CONTROLS
“ ” switch
Mode
AM/FM Radio
CD
MP3/WMA/
AAC disc
USB
iPod
BT audio
Function
Press
Preset station up/down
Press and hold
(0.8 sec. or more)
Seek up/down continuously while the switch is being
pressed
Press
Preset channel up/down
Press and hold
(0.8 sec. or more)
Type seek up/down
Press and hold
(1.5 sec. or more)
Fast up/down
Press
Track up/down
Press and hold
(0.8 sec. or more)
Fast forward/rewind
Press
File up/down
Press and hold
(0.8 sec. or more)
Fast forward/rewind
Press
File/Track up/down
Press and hold
(0.8 sec. or more)
Fast forward/rewind
Press
Track/File up/down
Press
Track up/down
Press and hold
(0.8 sec. or more)
Fast forward/rewind
3
AUDIO SYSTEM
XM
Operation
Volume control switch
Mode
All
Operation
Function
Press
Volume up/down
Press and hold
(0.8 sec. or more)
Volume up/down continuously
INFORMATION
● In the APPS mode, some operation may be done on the screen depend on the selected
APPS.
113
5. SETUP
1. AUDIO SETTINGS
Detailed audio settings can be programmed.
1
AUDIO SETTINGS SCREEN
Press the “APPS” button.
No.
2
3
4
114
Select “Setup”.
Select “Audio”.
Select the items to be set.
Function
Page
Select to change the number of preset radio stations/channels displayed
on the screen.
115
Select to set cover art settings on/off.

Select to set automatic
sound levelizer.
70
Select to enable cache radio.

Select to reset all setup
items.

5. SETUP
SETTING THE NUMBER OF
RADIO PRESETS
1
Display the “Audio Settings” screen.
(P.114)
2
3
Select “Number of Radio Presets”.
3
AUDIO SYSTEM
Select the button with the desired number to be displayed.
115
6. TIPS FOR OPERATING THE AUDIO SYSTEM
1. OPERATING INFORMATION
NOTICE
● To avoid damage to the audio system:
• Be careful not to spill beverages over
the audio system.
• Do not put anything other than an
appropriate disc into the disc slot.
INFORMATION
● The use of a cellular phone inside or
near the vehicle may cause a noise from
the speakers of the audio system which
you are listening to. However, this does
not indicate a malfunction.
RADIO
Usually, a problem with radio reception
does not mean there is a problem with
the radio — it is just the normal result
of conditions outside the vehicle.
For example, nearby buildings and terrain can interfere with FM reception.
Power lines or phone wires can interfere with AM signals. And of course, radio signals have a limited range. The
farther the vehicle is from a station, the
weaker its signal will be. In addition, reception conditions change constantly
as the vehicle moves.
Here, some common reception problems that probably do not indicate a
problem with the radio are described.
116
FM
Fading and drifting stations: Generally, the
effective range of FM is about 25 miles (40
km). Once outside this range, you may notice fading and drifting, which increase with
the distance from the radio transmitter.
They are often accompanied by distortion.
Multi-path: FM signals are reflective, making it possible for 2 signals to reach the vehicle’s antenna at the same time. If this
happens, the signals will cancel each other
out, causing a momentary flutter or loss of
reception.
Static and fluttering: These occur when
signals are blocked by buildings, trees or
other large objects. Increasing the bass
level may reduce static and fluttering.
Station swapping: If the FM signal being
listened to is interrupted or weakened, and
there is another strong station nearby on
the FM band, the radio may tune in the
second station until the original signal can
be picked up again.
AM
Fading: AM broadcasts are reflected by
the upper atmosphere — especially at
night. These reflected signals can interfere
with those received directly from the radio
station, causing the radio station to sound
alternately strong and weak.
Station interference: When a reflected signal and a signal received directly from a radio station are very nearly the same
frequency, they can interfere with each
other, making it difficult to hear the broadcast.
Static: AM is easily affected by external
sources of electrical noise, such as high
tension power lines, lightening or electrical
motors. This results in static.
6. TIPS FOR OPERATING THE AUDIO SYSTEM
XM
 Cargo loaded on the roof luggage carrier,
especially metal objects, may adversely
affect the reception of XM Satellite Radio.
 Alternation or modifications carried out
without appropriate authorization may
invalidate the user’s right to operate the
equipment.
 This CD player is intended for use with 4.7
in. (12 cm). discs only.
 Extremely high temperatures can keep the
CD player from working. On hot days, use
the air conditioning system to cool the
inside of the vehicle before using the
player.
 Bumpy roads or other vibrations may
make the CD player skip.
 If moisture gets into the CD player, the
discs may not be able to be played.
Remove the discs from the player and
wait until it dries.
 Use only discs marked as shown above.
The following products may not be playable on your player:
• SACD
• dts CD
• Copy-protected CD
• Video CD
WARNING
● The CD player uses an invisible laser
beam which could cause hazardous
radiation exposure if directed outside the
unit. Be sure to operate the player correctly.
117
3
AUDIO SYSTEM
CD PLAYER AND DISC
Audio CDs
6. TIPS FOR OPERATING THE AUDIO SYSTEM
Special shaped discs
Transparent/translucent discs
NOTICE
● Do not use special shaped, transparent/
translucent, low quality or labeled discs
such as those shown in the illustrations.
The use of such discs may damage the
player, or it may be impossible to eject
the disc.
● This system is not designed for use of
Dual Discs. Do not use Dual Discs
because they may cause damage to the
player.
● Do not use discs with a protection ring.
The use of such discs may damage the
player, or it may be impossible to eject
the disc.
● Do not use printable discs. The use of
such discs may damage the player, or it
may be impossible to eject the disc.
Low quality discs
Correct
Labeled discs
118
Wrong
 Handle discs carefully, especially when
inserting them. Hold them on the edge
and do not bend them. Avoid getting fingerprints on them, particularly on the shiny
side.
 Dirt, scratches, warping, pin holes or other
disc damage could cause the player to
skip or to repeat a section of a track. (To
see a pin hole, hold the disc up to the
light.)
 Remove discs from the players when not
in use. Store them in their plastic cases
away from moisture, heat and direct sunlight.
6. TIPS FOR OPERATING THE AUDIO SYSTEM
iPod
3
CD-R/RW DISCS
 CD-R/CD-RW discs that have not been
subject to the “finalizing process” (a process that allows discs to be played on a
conventional CD player) cannot be
played.
 It may not be possible to play CD-R/CDRW discs recorded on a music CD
recorder or a personal computer because
of disc characteristics, scratches or dirt on
the disc, or dirt, condensation, etc. on the
lens of the unit.
 It may not be possible to play discs
recorded on a personal computer depending on the application settings and the
environment. Record with the correct format. (For details, contact the appropriate
application manufacturers of the applications.)
 CD-R/CD-RW discs may be damaged by
direct exposure to sunlight, high temperatures or other storage conditions. The unit
may be unable to play some damaged
discs.
 If you insert a CD-RW disc into the player,
playback will begin more slowly than with
a conventional CD or CD-R disc.
 Recordings on CD-R/CD-RW cannot be
played using the DDCD (Double Density
CD) system.
 “Made for iPod” and “Made for iPhone”
mean that an electronic accessory has
been designed to connect specifically to
iPod or iPhone respectively, and has been
certified by the developer to meet Apple
performance standards.
 Apple is not responsible for the operation
of this device or its compliance with safety
and regulatory standards. Please note
that the use of this accessory with iPod or
iPhone may affect wireless performance.
 iPhone, iPod, iPod classic, iPod nano, and
iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Lightning is a trademark of Apple Inc.
119
AUDIO SYSTEM
To clean a disc: Wipe it with a soft, lintfree cloth that has been dampened with
water. Wipe in a straight line from the center to the edge of the disc (not in circles).
Dry it with another soft, lint-free cloth. Do
not use a conventional record cleaner or
anti-static device.
6. TIPS FOR OPERATING THE AUDIO SYSTEM
COMPATIBLE MODELS
The following iPod®, iPod nano®, iPod
classic®, iPod touch® and iPhone® devices can be used with this system.
Made for
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
iPod touch (5th generation)*
iPod touch (4th generation)
iPod touch (3rd generation)
iPod touch (2nd generation)
iPod touch (1st generation)
iPod classic
iPod with video
iPod nano (7th generation)*
iPod nano (6th generation)
iPod nano (5th generation)
iPod nano (4th generation)
iPod nano (3rd generation)
iPod nano (2nd generation)
iPod nano (1st generation)
iPhone 5*
iPhone 4S
iPhone 4
iPhone 3GS
iPhone 3G
iPhone
FILE INFORMATION
■COMPATIBLE USB DEVICES
USB communication
formats
USB 2.0 HS (480
Mbps) and FS
(12 Mbps)
File formats
FAT 16/32
Correspondence class
Mass
class
■COMPATIBLE
storage
COMPRESSED
FILES
Item
Compatible
file format
USB/iPod
DISC
MP3/WMA/AAC
Folders in the
device
Maximum
3000
Maximum
192
Files in the
device
Maximum
9999
Maximum
255
Files per
folder
Maximum
255

*: iPod video not supported
Depending on differences between models or software versions etc., some models
might be incompatible with this system.
120
6. TIPS FOR OPERATING THE AUDIO SYSTEM
■CORRESPONDING
SAMPLING
■COMPATIBLE CHANNEL MODES
FREQUENCY
File type
File type
Frequency (kHz)
32/44.1/48
MP3 files:
MPEG 2 LSF LAYER 3
16/22.05/24
WMA files:
Ver. 7, 8, 9* (9.1/9.2)
32/44.1/48
AAC files:
MPEG4/AAC-LC
11.025/12/16/
22.05/24/32/
44.1/48
*: Only compatible with Windows Media Audio Standard
■CORRESPONDING BIT RATES
File type
Bit rate (kbps)
MP3 files:
MPEG 1 LAYER 3
32 - 320
MP3 files:
MPEG 2 LSF LAYER 3
8 - 160
WMA files: Ver. 7, 8
CBR 48 - 192
WMA files:
Ver. 9* (9.1/9.2)
CBR 48 - 320
AAC files:
MPEG4/AAC-LC
16 - 320
*: Only compatible with Windows Media Audio Standard
(Variable Bit Rate (VBR) compatible)
MP3 files
Stereo, joint stereo, dual
channel and monaural
WMA files
2ch
AAC files
1ch, 2ch (Dual channel is not
supported)
 MP3 (MPEG Audio Layer 3), WMA
(Windows Media Audio) and AAC
(Advanced Audio Coding) are audio compression standards.
 This system can play MP3/WMA/AAC files
on CD-R/CD-RW discs and USB memory.
 This system can play disc recordings compatible with ISO 9660 level 1 and level 2
and with the Romeo and Joliet file system
and UDF (2.01 or lower).
 When naming an MP3/WMA/AAC file, add
an appropriate file extension (.mp3/.wma/
.m4a).
 This system plays back files with .mp3/
.wma/.m4a file extensions as MP3/WMA/
AAC files respectively. To prevent noise
and playback errors, use the appropriate
file extension.
 This system can play only the first session
when using multi-session compatible
discs.
 MP3 files are compatible with the ID3 Tag
Ver. 1.0, Ver. 1.1, Ver. 2.2 and Ver. 2.3 formats. This system cannot display disc
title, track title and artist name in other formats.
 WMA/AAC files can contain a WMA/AAC
tag that is used in the same way as an ID3
tag. WMA/AAC tags carry information
such as track title and artist name.
 The emphasis function is available only
when playing MP3 files.
 This system can play back AAC files
encoded by iTunes.
121
3
AUDIO SYSTEM
MP3 files:
MPEG 1 LAYER 3
Channel mode
6. TIPS FOR OPERATING THE AUDIO SYSTEM
 The sound quality of MP3/WMA files generally improves with higher bit rates. In
order to achieve a reasonable level of
sound quality, discs recorded with a bit
rate of at least 128 kbps are recommended.
 M3u playlists are not compatible with the
audio player.
 MP3i (MP3 interactive) and MP3PRO formats are not compatible with the audio
player.
 The player is compatible with VBR (Variable Bit Rate).
 When playing back files recorded as VBR
(Variable Bit Rate) files, the play time will
not be correctly displayed if the fast forward or reverse operations are used.
 It is not possible to check folders that do
not include MP3/WMA/AAC files.
 MP3/WMA/AAC files in folders up to 8 levels deep can be played. However, the
start of playback may be delayed when
using discs containing numerous levels of
folders. For this reason, we recommend
creating discs with no more than 2 levels
of folders.
122
001.mp3
002.wma
Folder 1
003.mp3
Folder 2
004.mp3
005.wma
Folder 3
006.m4a
 The play order of the compact disc with
the structure shown above is as follows:
001.mp3
002.wma . . .
006.m4a
 The order changes depending on the personal computer and MP3/WMA/AAC
encoding software you use.
6. TIPS FOR OPERATING THE AUDIO SYSTEM
TERMS
PACKET WRITE
 This is a general term that describes the
process of writing data on-demand to CDR, etc., in the same way that data is written to floppy or hard discs.
 This is a method of embedding trackrelated information in an MP3 file. This
embedded information can include the
track number, track title, the artist’s name,
the album title, the music genre, the year
of production, comments, cover art and
other data. The contents can be freely
edited using software with ID3 tag editing
functions. Although the tags are restricted
to a number of characters, the information
can be viewed when the track is played
back.
WMA TAG
 WMA files can contain a WMA tag that is
used in the same way as an ID3 tag. WMA
tags carry information such as track title
and artist name.
ISO 9660 FORMAT
 This is the international standard for the
formatting of CD-ROM folders and files.
For the ISO 9660 format, there are 2 levels of regulations.
 Level 1: The file name is in 8.3 format (8
character file names, with a 3 character
file extension. File names must be composed of one-byte capital letters and numbers. The “_” symbol may also be
included.)
 Level 2: The file name can have up to 31
characters (including the separation mark
“.” and file extension). Each folder must
contain fewer than 8 hierarchies.
 Playlists created using “WINAMP” software have a playlist file extension (.m3u).
MP3
 MP3 is an audio compression standard
determined by a working group (MPEG) of
the ISO (International Standard Organization). MP3 compresses audio data to
about 1/10 the size of that on conventional
discs.
WMA
 WMA (Windows Media Audio) is an audio
compression
format
developed
by
Microsoft®. It compresses files into a size
smaller than that of MP3 files. The decoding formats for WMA files are Ver. 7, 8 and
9.
 This product is protected by certain intellectual property rights of Microsoft Corporation and third parties. Use or distribution
of such technology outside of this product
is prohibited without a license from
Microsoft or an authorized Microsoft subsidiary and third parties.
AAC
 AAC is short for Advanced Audio Coding
and refers to an audio compression technology standard used with MPEG2 and
MPEG4.
123
3
AUDIO SYSTEM
ID3 TAG
m3u
6. TIPS FOR OPERATING THE AUDIO SYSTEM
ERROR MESSAGES
Mode
CD
USB
iPod
Message
Explanation
“No music files found.”
This indicates that no MP3/WMA/AAC files are
included in the disc.
“Check Disc”
It indicates that the disc is dirty, damaged, or it
was inserted upside down. Clean the disc or insert it correctly.
It indicates a disc which is not playable is inserted.
“Disc Error”
There is a trouble inside the system.
Eject the disc.
“Connection error. Please
consult your Owner’s
Manual for instructions on
how to connect the USB
device.”
This indicates a problem in the USB memory or
its connection.
“There are no files available for playback. Please
add compatible files to
your USB device.”
This indicates that no MP3/WMA/AAC files are
included in the USB memory.
“Connection error. Please
consult your Owner’s
Manual for instructions on
how to connect the iPod.”
This indicates a problem in the iPod or its connection.
“There are no songs available for playback. Please
add compatible files to
your iPod.”
This indicates that there is no music data in the
iPod.
“No videos found.”
This indicates that no video files are included in
the iPod.
“iPod authorization unsuccessful.”
This indicates that it failed to authorize the iPod.
Please check your iPod.
INFORMATION
● If the malfunction is not rectified: Take your vehicle to your Toyota dealer.
124
4
1
VOICE COMMAND SYSTEM
2
VOICE COMMAND SYSTEM
OPERATION
3
1. VOICE COMMAND SYSTEM...... 126
4
1
USING THE VOICE COMMAND
SYSTEM............................................ 126
VOICE COMMAND SYSTEM
OPERATION ..................................... 127
2. CASUAL SPEECH
RECOGNIZATION..................... 132
3. COMMAND LIST ......................... 133
5
6
7
8
9
125
1. VOICE COMMAND SYSTEM OPERATION
1. VOICE COMMAND SYSTEM
The voice command system enables
the audio, hands-free systems, etc. to
be operated using voice commands.
MICROPHONE
Vehicles without moon roof
Refer to the command list for samples
of voice commands. (P.133)
USING THE VOICE
COMMAND SYSTEM
STEERING SWITCH
Vehicles with moon roof
Talk switch
 Press the talk switch to start the voice
command system.
 To cancel voice recognition, press and
hold the talk switch.
126
 It is unnecessary to speak directly into the
microphone when giving a command.
1. VOICE COMMAND SYSTEM OPERATION
INFORMATION
The voice command system is operated by speaking commands corresponding to each function. Also you
can confirm the each command by selecting a tab.
The tabs are found on the upper part of
the screen.
All commands that are not displayed
on the screen can be recognized on
any screens.
1
Press the talk switch.
 Voice guidance for the voice command
system can be skipped by pressing the
talk switch.
2
Say the tab selection command or select the desired tab.
 Commands related with each function are
displayed on the screen of the each function tab. Some commonly used commands are displayed on the screen of the
function tab.
 Selecting “Help” or saying “Help”
prompts voice guidance to offer examples of commands and operation methods.
127
4
VOICE COMMAND SYSTEM
● The voice command system can be
operated while guidance is being spoken, when “Voice Prompt Interrupt”
(P.58) is set to on. (It is not necessary
to wait for the confirmation beep before
speaking a command.)
● Voice commands may not be recognized
if:
• Spoken too quickly.
• Spoken at a low or high volume.
• The roof or windows are open.
• Passengers are talking while voice
commands are spoken.
• The air conditioning speed is set high.
• The air conditioning vents are turned
towards the microphone.
● In the following conditions, the system
may not recognize the command properly and using voice commands may not
be possible:
• The command is incorrect or unclear.
Note that certain words, accents or
speech patterns may be difficult for the
system to recognize.
• There is excessive background noise,
such as wind noise.
VOICE COMMAND SYSTEM
OPERATION
1. VOICE COMMAND SYSTEM OPERATION
3
Say the command displayed on the
screen.
 Registered POIs, registered names in the
contacts list etc., can be said in the place
of the “<>” next to the commands.
(P.133)
For example: Say “Find nearby dining”,
“Call John smith” etc.
 If a desired outcome is not shown, or if no
selections are available, perform one of
the following to return to the previous
screen:
• Say “Go back”.
• Select “Go Back”.
 To cancel voice recognition, select “Cancel”, or press and hold the talk switch.
■DISPLAYING THE “Voice Settings”
SCREENS
 Selecting “Voice Settings” can be displayed the “Voice Settings” screen.
(P.58)
■INCREASING THE VOICE RECOGNITION PERFORMANCE
In order to improve voice recognition performance, select “Train Voice Recognition” on the “Voice Settings” screen.
(P.58)
When “Train Voice Recognition” is selected, the user will be asked to say 10 sample
phrases. This will help the voice command
system adapt to the user’s accent.
INFORMATION
● If the system does not respond or the
confirmation screen does not disappear,
press the talk switch and try again.
● “Voice Recognition Prompts” can be set
on the “Voice Settings” screen. (P.58)
● Some voice guidance can be canceled
by setting voice prompts to off. Use this
setting when it is desirable to say a command immediately after pressing the talk
switch and hearing a beep.
128
VOICE COMMAND EXAMPLE:
LAUNCH Entune App Suite
APPLICATION
1
2
Press the talk switch.
Say “Launch <application name>”.
 Entune App Suite application screen is
displayed.
1. VOICE COMMAND SYSTEM OPERATION
VOICE COMMAND EXAMPLE:
PERFORMING A DESTINATION
SEARCH BY ADDRESS
(ENGLISH ONLY)
1
2
3
● The voice command recognition is
designed to recognize the main body of
the official street name.
Say “Enter an address”.
For example: if the official street name is
“East Main Street”, the voice command
recognition will recognize “Main”.
Say “<house number, street name,
city name, State>” continuously.
For example: Say “West 555”.
Press the talk switch.
 For information regarding the state/
province setting to perform a destination
search by address: P.207
Say “Go directly”.
 After this, follow the voice guidance and
search for a destination route by voice
command operation.
● Say the desired number, cardinal direction etc. in the place of the “<>”.
● Inputting the house number can be
skipped.
● Even if the state set using voice recognition is different from the set state in the
“Address” screen (which was set when a
destination was set manually), the set
state in the “Address” screen will not
change. (P.208)
● The house number voice recognition
conditions are outlined below:
• Numerals: 10 digits or less
• Numerals and cardinal direction or a
hyphen and numerals: A total of 9
digits or less (Do not say “and”.)
• Cardinal direction or a hyphen and
numerals: A total of 9 digits or less
(Do not say “and”.)
• Numerals are recognized as single
digits only.
• The cardinal direction and hyphens
are only recognized once.
• The following cardinal directions can
be recognized: North, East, West and
South.
129
4
VOICE COMMAND SYSTEM
 A confirmation screen will be displayed
showing the recognition results. If multiple
matching items are found, a selection
screen will be displayed. Say “<number>” or select the number.
 Some areas cannot be recognized by the
voice recognition system.
4
INFORMATION
1. VOICE COMMAND SYSTEM OPERATION
VOICE COMMAND EXAMPLE:
SEARCH FOR A SONG
VOICE COMMAND EXAMPLE:
CALL NAME
1
Press the talk switch.
1
Press the talk switch.
2
Say “Play song <name>”.
2
Say “Call
types>”.
 A confirmation screen will be displayed
showing the recognition results. If multiple
matching items are found, a selection
screen will be displayed. Say “<number>” or select the number.
 The system starts playing music and the
song lists are displayed.
<contacts>
<phone
 A confirmation screen will be displayed
showing the recognition results. If multiple
matching items are found, a selection
screen will be displayed. Say “<number>” or select the number.
INFORMATION
INFORMATION
● The Gracenote database is only compatible with the USB or iPod mode.
● A USB memory or iPod must be connected to enable track searching and
playback. (P.94, 99)
● When a USB memory or iPod is connected, recognition data is created so
tracks can be searched using voice
commands.
● Recognition data is updated under the
following conditions:
• When the USB memory or iPod data
has changed.
• When the voice recognition language
is changed. (P.52)
● While the recognition data is being created or being updated, a track search
cannot be performed using a voice command.
130
● In the same manner as it is displayed on
the screen, “Call <contacts> <phone
types>”, after saying “Call a contact”
say the name, or the name and type of
phone, of a contact.
For example: “Call a contact”, “John
Smith” or “Call a contact”, “Mary
Davis”, “Mobile”
● There are 4 types of phones: Home,
Mobile, Work and Other.
● Short or abbreviated names in the contacts list may not be recognized. Change
names in the contacts list to full names.
● Sometimes a voice recognition result
confirmation screen will be displayed.
After confirming the result, say “Yes” or
“No”.
● When the system recognizes multiple
names from the contacts list, a name
candidate list will be displayed on the
screen. If the desired name is not displayed on the top of the screen, say or
select the number of the name from the
candidate list (number 1, number 2, etc.)
to select a name from the candidate list.
● When a contact has multiple phone
numbers registered in the contacts list, a
candidate list will be displayed. If the
desired phone number is not displayed
on the top of the screen, say or select
the number of the desired phone number from the candidate list (number 1,
number 2, etc.) to select a phone number from the candidate list.
1. VOICE COMMAND SYSTEM OPERATION
VOICE COMMAND EXAMPLE:
DIAL NUMBER
1
Press the talk switch.
2
Say the phone number.
 In the same manner as it is displayed on
the screen, “Dial <number>”, after saying
“Dial a number” say the phone number.
 Say the phone number one digit at a time.
For example, if the phone number is
2345678:
Say “two three four five six seven
eight”
Do not say “twenty three forty five sixty
seven eight”
Say “Call” or press the
the steering wheel.
VOICE COMMAND SYSTEM
3
4
switch on
 When the confirmation screen appears,
say “Yes” or select “Yes” or press the
switch on the steering wheel.
 When the system recognizes multiple
phone numbers, a phone number candidate list will be displayed on the screen.
switch on the steering
Pressing the
wheel makes a call to the top entry on
the list. If the desired phone number is
not displayed on the top of the screen,
say the number of the desired phone
number from the candidate list to select
a phone number from the candidate list.
131
1. VOICE COMMAND SYSTEM OPERATION
2. CASUAL SPEECH RECOGNIZATION
Due to natural language speech recognition technology, this system enables
recognition of a command when spoken naturally. However, the system
cannot recognize every variation of
each command. In some situations, it
is possible to omit the command for the
procedure and directly state the desired operation. Not all voice commands are displayed in the function
menu.
INFORMATION
● If the command cannot be recognized
completely, the command input screen
will be displayed. (Search results will be
shown based on the part of the command that was recognized.)
EXPRESSION EXAMPLES FOR
EACH FUNCTION
Command
Expression examples
“Go Home”
Navigate to my house.
Take me home.
“Enter an
Address”
I need directions to an
address.
Give me a street.
“Find Nearby
<POI category>”
Search for a <Restaurants> around here.
Find a <Restaurants>
nearby.
“Call
<name>
<type>”
Get
me
<Robert
Brown>.
Call <contacts> <phonetypes>.
“Dial <number>”
Call <911>.
“Play Artist
<name>”*
Play the artist <name>.
I want to hear the band
<name>.
“Play Album
<name>”*
Play album <name>.
*: Only for external music device
132
1. VOICE COMMAND SYSTEM OPERATION
3. COMMAND LIST
Recognizable voice commands and their actions are shown below.
 Frequently used commands are listed in the following tables.
 For devices that are not installed in the vehicle, the related commands will not be displayed in the screen. Also, according to conditions, other commands may not be displayed in the screen.
 The functions available may vary according to the system installed.
 Voice recognition language can be changed. (P.52)
Basic
4
Action
“Help”
Prompts voice guidance to offer examples of commands
or operation methods
“Go Back”
Returns to the previous screen
“Number one/two/three/four/five”
Selects the number on the list screen
“Next Page”
Displays the next page
“Previous Page”
Displays the previous page
“Go to <tab>”
Displays the command list of the selected tab
Apps
When the voice recognition language is set to English.
Command
“Launch <apps>”
Action
Activates the Entune App Suite application
Navigation
Command
Action
“Find Nearby <POI category>”
Displays a list of <POI category*> near the current position
“Enter an Address”
Enables setting a destination by saying the address
“Go Home”
Displays the route to home
“Cancel Route”
Stops the route guidance
*: For example; “Gas stations”, “Restaurants”, etc.
133
VOICE COMMAND SYSTEM
Command
1. VOICE COMMAND SYSTEM OPERATION
Phone
Command
Action
“Redial”
Places a call to the phone number of the latest outgoing
call
“Call Back”
Places a call to the phone number of latest incoming call
“Show Recent Calls”
Displays the call history screen
“Dial <phone number>”
Places a call to the said phone number
“Call <contacts> <phonetypes>”
Place a call to the said phone type of the contact from the
phone book
Audio
Command
Action
“Play Playlist <name>”
Plays tracks from the selected playlist
“Play Artist <name>”
Plays tracks from the selected artist
“Play Song <name>”
Plays the selected track
“Play Album <name>”
Plays tracks from the selected album
Information
Command
Action
“Show Forecast”
Displays weather information
“Show Traffic”
Displays traffic information
INFORMATION
● Commands relating to operation of the audio can only be performed when the audio is
turned on.
134
5
1
INFORMATION
2
1
USEFUL INFORMATION
3
1. RECEIVING WEATHER
INFORMATION ......................... 136
4
DISPLAYING WEATHER
INFORMATION ................................. 136
2. DATA SERVICES SETTINGS..... 138
5
SETTING DOWNLOAD METHODS .... 138
6
7
8
9
135
1. USEFUL INFORMATION
1. RECEIVING WEATHER INFORMATION
Weather information can be received
via the HD Radio broadcast or by the
Entune App Suite application on a
Bluetooth® phone. For details about
the Entune App Suite application:
P.259
3
Check that the “Weather” screen is displayed.
DISPLAYING WEATHER
INFORMATION
1
Press the “APPS” button.
No.
Function
Select to display the weather of the
current location. (P.137)
Select to display the weather of a
desired location in the recently
checked locations list.
Select to display the weather of a
desired location in the national cities
list.
2
Select “Weather”.
Select to display the weather of a
desired location in the other local cities list.
Select to display weather information over the map.
INFORMATION
● Weather information is available in the
48 states, D.C. and Alaska of the United
States.
● The weather for current location might
not show the closest city when it first displays.
136
1. USEFUL INFORMATION
DISPLAYING THE WEATHER
OF THE CURRENT LOCATION
1
Display
the
(P.136)
2
3
Select “Current Weather”.
“Weather”
screen.
Select the desired tab to be displayed.
INFORMATION
● If weather is set to the home screen, the
weather screen of the current location
will be displayed.
5
INFORMATION
137
1. USEFUL INFORMATION
2. DATA SERVICES SETTINGS
SETTING DOWNLOAD
METHODS
Data service information, which is
comprised of traffic information and
weather information, can be received
via the HD Radio broadcast and by the
Entune App Suite application on a
Bluetooth® phone. The receiving method can be set to both or only via the HD
Radio broadcast. For details about the
Entune App Suite application: P.259
1
Press the “APPS” button.
4
Select the desired item to be set.
 Select a checkbox on the right to set.
No.
Function
Select to receive data service information via both the HD Radio broadcast and the Entune App Suite
application on a Bluetooth® phone.
When both methods are available,
the HD Radio broadcast will be selected.
Select to receive data only via the
HD Radio broadcast.
INFORMATION
2
Select “Setup”.
3
Select “HD Data”.
138
● These settings are available in the 48
states, D.C. and Alaska of the United
States.
6
1
PERIPHERAL MONITORING SYSTEM
2
1
REAR VIEW MONITOR
SYSTEM
3
1. REAR VIEW MONITOR
SYSTEM .................................... 140
4
DRIVING PRECAUTIONS ................... 140
SCREEN DESCRIPTION .................... 141
5
2. REAR VIEW MONITOR
SYSTEM PRECAUTIONS......... 142
6
AREA DISPLAYED ON SCREEN........ 142
THE CAMERA ..................................... 142
DIFFERENCES BETWEEN
THE SCREEN AND
THE ACTUAL ROAD......................... 143
WHEN APPROACHING
THREE-DIMENSIONAL
OBJECTS .......................................... 145
7
8
9
3. THINGS YOU SHOULD
KNOW ....................................... 147
IF YOU NOTICE ANY SYMPTOMS .... 147
139
1. REAR VIEW MONITOR SYSTEM
1. REAR VIEW MONITOR SYSTEM*
The rear view monitor system assists
the driver by displaying an image of the
view behind the vehicle with fixed
guide lines on the screen while backing
up, for example while parking.
INFORMATION
● The screen illustrations used in this text
are intended as examples, and may differ from the image that is actually displayed on the screen.
DRIVING PRECAUTIONS
The rear view monitor system is a supplemental device intended to assist the
driver when backing up. When backing
up, be sure to visually check all around
the vehicle both directly and using the
mirrors before proceeding. If you do
not, you may hit another vehicle, and
could possibly cause an accident.
Pay attention to the following precautions when using the rear view monitor
system.
WARNING
● Never depend on the rear view monitor
system entirely when backing up. The
image and the position of the guide lines
displayed on the screen may differ from
the actual state.
Use caution, just as you would when
backing up any vehicle.
● Be sure to back up slowly, depressing
the brake pedal to control vehicle speed.
● The instructions given are only guidelines. When and how much to turn the
steering wheel will vary according to
traffic conditions, road surface conditions, vehicle condition, etc. when parking. It is necessary to be fully aware of
this before using the rear view monitor
system.
● When parking, be sure to check that the
parking space will accommodate your
vehicle before maneuvering into it.
● Do not use the rear view monitor system
in the following cases:
• On icy or slick road surfaces, or in
snow
• When using tire chains or emergency
tires
• When the backdoor is not closed completely
• On roads that are not flat or straight,
such as curves or slopes
● In low temperatures, the screen may
darken or the image may become faint.
The image could distort when the vehicle is moving, or you may become
unable to see the image on the screen.
Be sure to visually check all around the
vehicle both directly and using the mirrors before proceeding.
● If the tire sizes are changed, the position
of the fixed guide lines displayed on the
screen may change.
● The camera uses a special lens. The
distances between objects and pedestrians that appear in the image displayed
on the screen will differ from the actual
distances.(P.143)
*: If equipped
140
1. REAR VIEW MONITOR SYSTEM
SCREEN DESCRIPTION
The rear view monitor system screen will be displayed if the shift lever is shifted to
the “R” position while the power switch is in ON mode.
No.
Display
Function
6
Displays a guide path when the vehicle is being backed
straight up.
 The displayed width is wider than the actual vehicle
width.
Vehicle center guide line
This line indicates the estimated vehicle center on the
ground.
Distance guide line
Shows distance behind the vehicle.
 Displays a point approximately 1.5 ft. (0.5 m) (red) from
the edge of the bumper.
Distance guide line
Shows distance behind the vehicle.
 Displays a point approximately 3 ft. (1 m) (blue) from
the edge of the bumper.
CANCELING REAR VIEW MONITOR SYSTEM
The rear view monitor system is canceled when the shift lever is shifted into any
position other than the “R” position.
141
PERIPHERAL MONITORING SYSTEM
Vehicle width guide line
1. REAR VIEW MONITOR SYSTEM
2. REAR VIEW MONITOR SYSTEM PRECAUTIONS
AREA DISPLAYED ON
SCREEN
The rear view monitor system displays
an image of the view from the bumper
of the rear area of the vehicle.
THE CAMERA
The camera for the rear view monitor
system is located as shown in the illustration.
Displayed area
Screen
USING THE CAMERA
Corners of bumper
 The image adjustment procedure for the
rear view monitor system screen is the
same as the procedure for adjusting the
screen. (P.38)
INFORMATION
● The area displayed on the screen may
vary according to vehicle orientation
conditions.
● Objects which are close to either corner
of the bumper or under the bumper cannot be displayed.
● The camera uses a special lens. The
distance of the image that appears on
the screen differs from the actual distance.
● Items which are located higher than the
camera may not be displayed on the
monitor.
142
If the camera lens becomes dirty, it
cannot transmit a clear image. If water
droplets, snow or mud adhere to the
lens, rinse with water and wipe with a
soft cloth. If the lens is extremely dirty,
wash it with a mild cleanser and rinse.
1. REAR VIEW MONITOR SYSTEM
NOTICE
 The distance guide lines and the vehicle
width guide lines may not actually be parallel with the dividing lines of the parking
space, even when they appear to be so.
Be sure to check visually.
 The distances between the vehicle width
guide lines and the left and right dividing
lines of the parking space may not be
equal, even when they appear to be so.
Be sure to check visually.
 The distance guide lines give a distance
guide for flat road surfaces. In any of the
following situations, there is a margin of
error between the fixed guide lines on the
screen and the actual distance /course on
the road.
143
6
PERIPHERAL MONITORING SYSTEM
● The rear view monitor system may not
operate properly in the following cases.
• If the back of the vehicle is hit, the
position and mounting angle of the
camera may change.
• As the camera has a water proof construction, do not detach, disassemble
or modify it. This may cause incorrect
operation.
• Do not strongly rub the camera lens. If
the camera lens is scratched, it cannot
transmit a clear image.
• Do not allow organic solvent, car wax,
window cleaner or a glass coating to
adhere to the camera. If this happens,
wipe it off as soon as possible.
• If the temperature changes rapidly,
such as when hot water is poured on
the vehicle in cold weather, the system
may not operate normally.
• When washing the vehicle, do not
apply intensive bursts of water to the
camera or camera area. Doing so may
result in the camera malfunctioning.
● Do not expose the camera to strong
impact as this could cause a malfunction. If this happens, have the vehicle
inspected by your Toyota dealer as soon
as possible.
DIFFERENCES BETWEEN
THE SCREEN AND THE
ACTUAL ROAD
1. REAR VIEW MONITOR SYSTEM
WHEN THE GROUND BEHIND
THE VEHICLE SLOPES UP
SHARPLY
The distance guide lines will appear to
be closer to the vehicle than the actual
distance. Because of this, objects will
appear to be farther away than they actually are. In the same way, there will
be a margin of error between the
guidelines and the actual distance/
course on the road.
144
WHEN THE GROUND BEHIND
THE VEHICLE SLOPES DOWN
SHARPLY
The distance guide lines will appear to
be farther from the vehicle than the actual distance. Because of this, objects
will appear to be closer than they actually are. In the same way, there will be
a margin of error between the guide
lines and the actual distance/course on
the road.
1. REAR VIEW MONITOR SYSTEM
WHEN ANY PART OF THE
VEHICLE SAGS
When any part of the vehicle sags due
to the number of passengers or the distribution of the load, there is a margin
of error between the fixed guide lines
on the screen and the actual distance/
course on the road.
WHEN APPROACHING
THREE-DIMENSIONAL
OBJECTS
The distance guide lines are displayed
according to flat surfaced objects
(such as the road). It is not possible to
determine the position of three-dimensional objects (such as vehicles) using
the vehicle width guide lines and distance guide lines. When approaching a
three-dimensional object that extends
outward (such as the flatbed of a
truck), be careful of the following.
6
PERIPHERAL MONITORING SYSTEM
A margin of error
145
1. REAR VIEW MONITOR SYSTEM
VEHICLE WIDTH GUIDE LINES
Visually check the surroundings and
the area behind the vehicle. In the case
shown below, the truck appears to be
outside of the vehicle width guide lines
and the vehicle does not look as if it
hits the truck. However, the rear body
of the truck may actually cross over the
vehicle width guide lines. In reality if
you back up as guided by the vehicle
width guide lines, the vehicle may hit
the truck.
DISTANCE GUIDE LINES
Visually check the surroundings and
the area behind the vehicle. On the
screen, it appears that a truck is parking at point B. However, in reality if you
back up to point A, you will hit the truck.
On the screen, it appears that A is closest and C is farthest away. However, in
reality, the distance to A and C is the
same, and B is farther than A and C.
Positions of A, B and C
C
AB
C
B
A

146
Vehicle width guide lines
1. REAR VIEW MONITOR SYSTEM
3. THINGS YOU SHOULD KNOW
IF YOU NOTICE ANY SYMPTOMS
If you notice any of the following symptoms, refer to the likely cause and the solution, and re-check.
If the symptom is not resolved by the solution, have the vehicle inspected by
your Toyota dealer.
Symptom
Solution
 The vehicle is in a dark
area
 The temperature around
the lens is either high or low
 The outside temperature is
low
 There are water droplets on
the camera
 It is raining or humid
 Foreign matter (mud etc.) is
adhering to the camera
 Sunlight or headlights are
shining directly into the
camera
 The vehicle is under fluorescent
lights,
sodium
lights, mercury lights etc.
Back up while visually checking the vehicle’s surroundings. (Use the monitor again
once conditions have been
improved.)
The procedure for adjusting
the picture quality of the rear
view monitor system is the
same as the procedure for
adjusting the screen. (P.38)
The image is blurry
Dirt or foreign matter (such as
water droplets, snow, mud
etc.) is adhering to the camera.
Rinse the camera lens with
water and wipe it clean with a
soft cloth.
Wash with a mild soap if the
dirt is stubborn.
The image is out of alignment
The camera or surrounding
area has received a strong
impact.
Have the vehicle inspected by
your Toyota dealer.
The fixed guide lines are very
far out of alignment
The camera position is out of
alignment.
Have the vehicle inspected by
your Toyota dealer.
 The vehicle is tilted (there is
a heavy load on the vehicle,
tire pressure is low due to a
tire puncture, etc.)
 The vehicle is used on an
incline.
If this happens due to these
causes, it does not indicate a
malfunction.
Back up while visually checking the vehicle’s surroundings.
The image is difficult to see
147
6
PERIPHERAL MONITORING SYSTEM
Likely cause
1. REAR VIEW MONITOR SYSTEM
148
7
1
PHONE
2
1
PHONE OPERATION
(HANDS-FREE SYSTEM FOR
CELLULAR PHONES)
1. QUICK REFERENCE................... 150
5. TALKING ON THE
Bluetooth® PHONE .................. 160
INCOMING CALL WAITING ................ 162
6. Bluetooth® PHONE
MESSAGE FUNCTION ............. 163
RECEIVING A MESSAGE ................... 164
2. SOME BASICS ............................ 151
CHECKING MESSAGES..................... 164
REGISTERING/CONNECTING
A Bluetooth® PHONE........................ 151
REPLYING TO A MESSAGE
(QUICK REPLY) ................................ 165
USING THE PHONE SWITCH/
MICROPHONE ................................. 152
CALLING THE MESSAGE
SENDER ........................................... 166
VOICE COMMAND SYSTEM.............. 152
ABOUT THE CONTACTS
IN THE CONTACT LIST ................... 153
WHEN SELLING OR DISPOSING
OF THE VEHICLE............................. 153
5
6
SETUP
1. PHONE/MESSAGE
SETTINGS................................. 168
PHONE/MESSAGE SETTINGS
SCREEN ........................................... 168
BY FAVORITES LIST .......................... 155
“Sound Settings” SCREEN .................. 169
BY CALL HISTORY ............................. 155
BY CONTACTS LIST .......................... 156
“Contact/Call History Settings”
SCREEN ........................................... 170
BY DIAL PAD ...................................... 158
“Messaging Settings” SCREEN ........... 178
BY OFF HOOK SWITCH ..................... 158
“Phone Display Settings” SCREEN ..... 179
BY “Home” SCREEN ........................... 158
INCOMING CALLS.............................. 159
4
7
2
3. CALLING ON THE
Bluetooth® PHONE................... 154
4. RECEIVING ON THE
Bluetooth® PHONE................... 159
3
3
WHAT TO DO IF...
1. TROUBLESHOOTING ................ 180
149
8
9
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
1. QUICK REFERENCE
The phone top screen can be used to make a phone call. To display the hands-free
operation screen, press the “APPS” button and select “Phone”, the
switch on
the steering wheel or
switch on the instrument panel.
Several functions are available to operate on each screen that is displayed by selecting the 4 tabs.
Function
Page
Registering/connecting
Calling on the
Phone operation
Message function
Setting up a phone
150
Bluetooth®
Bluetooth®
phone
phone
40
154
Receiving on the Bluetooth® phone
159
Talking on the Bluetooth® phone
160
®
Using the Bluetooth phone message function
163
Phone settings
168
Bluetooth® settings
44
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
2. SOME BASICS
The hands-free system enables calls
to be made and received without having to take your hands off the steering
wheel.
This system supports Bluetooth®.
Bluetooth® is a wireless data system
that enables cellular phones to be used
without being connected by a cable or
placed in a cradle.
The operating procedure of the phone
is explained here.
WARNING
● While driving, do not use a cellular
phone or connect the Bluetooth® phone.
● Before using Bluetooth® devices, users
of any electrical medical device other
than implantable cardiac pacemakers,
cardiac resynchronization therapy-pacemakers or implantable cardioverter
defibrillators should consult the manufacturer of the device for information
about its operation under the influence
of radio waves. Radio waves could have
unexpected effects on the operation of
such medical devices.
● If your cellular phone does not support
Bluetooth®, this system cannot function.
● In the following conditions, the system
may not function:
• The cellular phone is turned off.
• The current position is outside the
communication area.
• The cellular phone is not connected.
• The cellular phone has a low battery.
● When using Bluetooth® audio and
hands-free at the same time, the following problems may occur:
• The Bluetooth® connection may be
cut.
• Noise may be heard on the Bluetooth®
audio playback.
REGISTERING/CONNECTING
A Bluetooth® PHONE
To use the hands-free system for cellular phones, it is necessary to register a
cellular phone with the system.
(P.40)
Bluetooth® PHONE CONDITION
DISPLAY
The condition of the Bluetooth® phone
appears on the upper right side of the
screen. (P.16)
NOTICE
● Do not leave your cellular phone in the
vehicle. The temperature inside may rise
to a level that could damage the phone.
151
7
PHONE
● Your audio unit is fitted with Bluetooth®
antennas. People with implantable cardiac pacemakers, cardiac resynchronization
therapy-pacemakers
or
implantable cardioverter defibrillators
should maintain a reasonable distance
between themselves and the Bluetooth®
antennas. The radio waves may affect
the operation of such devices.
INFORMATION
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
USING THE PHONE SWITCH/
MICROPHONE
■STEERING SWITCH
■MICROPHONE
The microphone is used when talking
on the phone.
Vehicles without moon roof
By pressing the phone switch, a call
can be received or ended without taking your hands off the steering wheel.
Vehicles with moon roof
Volume control switch
 Press the “+” side to increase the volume.
 Press the “-” side to decrease the volume.
On hook switch
Off hook switch
VOICE COMMAND SYSTEM
Press this switch to operate the voice
command system.
152
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
 The voice command system and its list
of commands can be operated.
(P.126)
INFORMATION
 The following data is stored for every registered phone. When another phone is
connected, the following registered data
cannot be read:
• Contact data
• Call history data
• Favorites data
• Image data
• All phone settings
• Message settings
INFORMATION
● When a phone’s registration is deleted,
the above-mentioned data is also
deleted.
WHEN SELLING OR
DISPOSING OF THE VEHICLE
A lot of personal data is registered
when the hands-free system is used.
When selling or disposing of the vehicle, initialize the data. (P.57)
 The following data in the system can be
initialized:
• Contact data
• Call history data
• Favorites data
• Image data
• All phone settings
• Message settings
INFORMATION
● Once initialized, the data and settings
will be erased. Pay much attention when
initializing the data.
153
7
PHONE
● The other party’s voice will be heard
from the front speakers. The audio system will be muted during phone calls or
when hands-free voice commands are
used.
● Talk alternately with the other party on
the phone. If both parties speak at the
same time, the other party may not hear
what has been said. (This is not a malfunction.)
● Keep call volume down. Otherwise, the
other party’s voice may be audible outside the vehicle and voice echo may
increase. When talking on the phone,
speak clearly towards the microphone.
● The other party may not hear you clearly
when:
• Driving on an unpaved road. (Making
excessive traffic noise.)
• Driving at high speeds.
• The roof or windows are open.
• The air conditioning vents are pointed
towards the microphone.
• The sound of the air conditioning fan is
loud.
• There is a negative effect on sound
quality due to the phone and/or network being used.
ABOUT THE CONTACTS IN
THE CONTACT LIST
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
3. CALLING ON THE Bluetooth® PHONE
After a Bluetooth® phone has been
registered, a call can be made using
the hands-free system. There are several methods by which a call can be
made, as described below.
1
Press the “APPS” button.
2
3
Select “Phone”.
Select the desired tab to call from.
 The phone top screen can be displayed by
pressing the
wheel or
panel.
154
switch on the steering
switch on the instrument
How to make a call list
Page
By favorites list
155
By call history
155
By contacts list*
156
By dial pad*
158
By e-mail/SMS/MMS
166
By POI call
199
By off hook switch
158
By Entune App Suite*
266
By voice command system
130
By “Home” screen
158
*: The operation cannot be performed while
driving.
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
BY FAVORITES LIST
BY CALL HISTORY
Calls can be made using registered
contacts which can be selected from a
contact list. (P.175)
Up to 30 of the latest call history items
(missed, incoming and outgoing) can
be selected from the “Call History” tab.
1
Display the
(P.154)
screen.
1
Display the
(P.154)
2
Select the “Favorites” tab and select
the desired contact.
2
Select the “Call History” tab and se-
Select the desired number.
 The icons of call type are displayed.
top
lect
Check that the “Call” screen is displayed.
phone
top
screen.
or the desired contact.
7
PHONE
3
4
phone
: Missed call
: Incoming call
: Outgoing call
When
3
is selected
Check that the “Call” screen is displayed.
When the desired contact is selected
3
4
Select the desired number.
Check that the “Call” screen is displayed.
155
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
INFORMATION
● When making a call to the same number
continuously, only the most recent call is
listed in call history.
● When a phone number registered in the
contact list is received, the name is displayed.
● Number-withheld calls are also memorized in the system.
● International phone calls may not be
made depending on the type of cellular
phone you have.
● The list should group together consecutive entries with the same phone number
and same call type. For example, two
calls from Kay Rowles’s mobile would
be displayed as follows: Kay Rowles (2)
● By pressing the
switch on the steering wheel, a call to the latest history item
can be made.
156
BY CONTACTS LIST
Calls can be made by using contact
data which is transferred from a registered cellular phone. (P.157)
Up to 2500 contacts (maximum of 4
phone numbers and e-mail addresses
per contact) can be registered in the
contact list.
1
Display the
(P.154)
2
Select the “Contacts” tab and select
the desired contact.
3
4
Select the desired number.
phone
top
screen.
Check that the “Call” screen is displayed.
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
WHEN THE CONTACT IS
EMPTY
■FOR
PBAP
No.
Select to transfer the contacts from
the connected cellular phone.
COMPATIBLE
Select to add a new contact manually.
®
Bluetooth PHONES
When “Automatic Transfer” is set to on
(P.170)
 Contacts are transferred automatically.
When “Automatic Transfer” is set to off
(P.170)
1
Function
Select to cancel transferring.
When “Transfer” is selected
2
Select the desired item.
Follow the steps in “FOR PBAP INCOMPATIBLE BUT OPP COMPATIBLE Bluetooth® PHONES” from
“STEP 2”. (P.171)
When “Add” is selected
2
Follow the steps in “REGISTERING A
NEW CONTACT TO THE CONTACT
LIST” from “STEP 2”. (P.172)
Function
Select to transfer new contacts from
a cellular phone, select “Always”
and then enable “Automatic Transfer”.
Select to transfer all the contacts
from a connected cellular phone
only once.
Select to cancel transferring.
■FOR PBAP INCOMPATIBLE BUT
OPP COMPATIBLE
PHONES
1
● Manual transfer operation cannot be
performed while driving.
● If your cellular phone is neither PBAP
nor OPP compatible, the contacts cannot be transferred.
● Depending on the type of Bluetooth®
phone:
• It may be necessary to perform additional steps on the phone when transferring contact data.
• The registered image in the contact list
may not transfer depending on the
type of Bluetooth® phone connected.
Bluetooth®
Select the desired item.
157
PHONE
INFORMATION
No.
7
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
BY DIAL PAD
BY “Home” SCREEN
1
Display the
(P.154)
2
Select the “Dial Pad” tab and enter the
phone number.
3
phone
top
Select
or press the
the steering wheel.
4
screen.
Display the home screen. (P.34)
2
Select the desired contact.
3
Check that the “Call” screen is displayed.
switch on
Check that the “Call” screen is displayed.
INFORMATION
● Depending on the type of Bluetooth®
phone being connected, it may be necessary to perform additional steps on
the phone.
BY OFF HOOK SWITCH
Calls can be made using the latest call
history item.
1
Press the
switch on the steering
wheel to display the phone top screen.
2
Press the
switch on the steering
wheel to display the “Call History”
screen.
3
Press the
switch on the steering
wheel to call the latest history item.
4
Check that the “Call” screen is displayed.
158
1
REGISTERING A NEW
CONTACT
1
Select and hold the screen button to
add a contact.
2
3
Select the desired contact.
Select the desired number.
INFORMATION
● If there is no contact in the contacts list,
the contacts cannot be registered at the
home screen.
● The contact cannot be registered at the
home screen while driving.
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
4. RECEIVING ON THE Bluetooth® PHONE
INCOMING CALLS
When a call is received, this screen is
displayed with a sound.
1
Select
or press the
switch on
the steering wheel to talk on the phone.
To refuse to receive the call: Select
or press the
switch on the steering wheel.
To adjust the volume of a received call:
Turn the “PWR·VOL” knob, or use the volume control switch on the steering wheel.
7
PHONE
INFORMATION
● During international phone calls, the
other party’s name or number may not
be displayed correctly depending on the
type of cellular phone you have.
● The incoming call display mode can be
set. (P.179)
● The ringtone that has been set in the
“Sound Settings” screen sounds when
there is an incoming call. Depending on
the type of Bluetooth® phone, both the
system and Bluetooth® phone may
sound simultaneously when there is an
incoming call. (P.169)
159
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
5. TALKING ON THE Bluetooth® PHONE
While talking on the phone, this screen
is displayed. The operations outlined
below can be performed on this
screen.
No.
160
Function
Page
Select to display the dial
pad to send tones.
160
Select to mute your voice
to the other party.

Select to change handset
modes between handsfree and cellular phone.

INFORMATION
● Changing from hands-free call to cellular
phone call is not possible while driving.
● When cellular phone call is changed to
hands-free call, the hands-free screen
will be displayed and its functions can be
operated on the screen.
● Changing between cellular phone call
and hands-free call can be performed by
operating the cellular phone directly.
● Transferring methods and operations
will be different depending on the type of
cellular phone you have.
● For the operation of the cellular phone,
see the manual that comes with it.
SENDING TONES
Select to adjust your voice
volume that the other party
hears from their speaker.
161
Select to send tones. This
button only appears when
a number that contains a
(w) is dialed in hands-free
mode.
161
Select to hang up the
phone.

Select “+” or “-” to adjust
the volume of the other party’s voice.

Select to start talking with
the other party.
162
■BY DIAL PAD
This operation cannot be performed
while driving.
1
Select “0-9”.
2
Enter the desired number.
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
■BY SELECTING “Release Tones”
“Release Tones” appear when a continuous tone signal(s) containing a (w)
is registered in the contact list.
TRANSMIT VOLUME SETTING
1
2
Select “Transmit Volume”.
3
Select “OK”.
This operation can be performed while
driving.
1
Select the desired level for the transmit
volume.
Select “Release Tones”.
INFORMATION
INFORMATION
● The sound quality of the voice heard
from the other party’s speaker may be
negatively impacted.
● To reset the transmit volume, select
“Default”.
● “Transmit Volume” is dimmed when
mute is on.
161
7
PHONE
● A continuous tone signal is a character
string that consists of numbers and the
characters
p
or
w.
(e.g.
056133w0123p#1)
● When the “p” pause tone is used, the
tone data up until the next pause tone
will be automatically sent after 2 seconds have elapsed. When the “w” pause
tone is used, the tone data up until the
next pause tone will be automatically
sent after a user operation is performed.
● Release tones can be used when automated operation of a phone based service such as an answering machine or
bank phone service is desired. A phone
number with continuous tone signals
can be registered in the contact list.
● Tone data after a “w” pause tone can be
operated on voice command during a
call.
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
INCOMING CALL WAITING
When a call is interrupted by a third
party while talking, this screen is displayed.
1
Select
or press the
switch on
the steering wheel to start talking with
the other party.
To refuse to receive the call: Select
or press the
ing wheel.
switch on the steer-
 Each time
is selected or the
switch on the steering wheel is pressed
during an interrupted call, the party who is
on hold will be switched.
INFORMATION
● This function may not be available
depending on the type of cellular phone.
162
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
6. Bluetooth® PHONE MESSAGE FUNCTION
Received messages can be forwarded
from the connected Bluetooth® phone,
enabling checking and replying using
the system.
Depending on the type of Bluetooth®
phone connected, received messages
may not be transferred to the message
inbox.
3
Select
.
 The phone top screen can be displayed by
switch on the steering
pressing the
wheel or
panel.
4
switch on the instrument
Check that the message inbox screen
is displayed.
If the phone does not support the message function, this function cannot be
used.
1
Press the “APPS” button.
: Select to change to phone mode.
Page
7
Receiving a message
164
Checking messages
164
PHONE
Replying to a message (quick reply)
165
Calling the message sender
166
Message settings
178
Function
2
Select “Phone”.
 You can also display the message inbox
screen to select “Messages”. (STEP4)
163
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
RECEIVING A MESSAGE
When an e-mail/SMS/MMS is received, the incoming message screen
pops up with sound and is ready to be
operated on the screen.
No.
CHECKING MESSAGES
1
Display the message inbox screen.
(P.163)
2
Select the desired message from the
list.
3
Check that the message is displayed.
Function
Select to check the message.
No.
Select to not open the message.
Select to call the message sender.
INFORMATION
● Depending on the cellular phone used
for receiving messages, or its registration status with the system, some information may not be displayed.
● The pop up screen is separately available for incoming e-mail and SMS/MMS
messages under the following conditions:
E-mail:
• “Incoming E-mail Display” is set to “Full
Screen”. (P.178)
• “E-mail Notification Popup” is set to on.
(P.178)
SMS/MMS:
• “Incoming SMS/MMS Display” is set to
“Full Screen”. (P.178)
• “SMS/MMS Notification Popup” is set
to on. (P.178)
164
*
Function
Select “Mark Unread” or “Mark
Read” to mark mail unread or read
on the message inbox screen.
This function is available when “Update Read Status on Phone” is set to
on. (P.178)
Select to
(P.165)
reply
the
message.
Select to display the previous or
next message.
Select to have messages read out.
To cancel this function, select
“Stop”.
When “Automatic Message Readout” is set to on, messages will be
automatically read out. (P.178)
Select to make a call to the sender.
*: E-mail only
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
INFORMATION
● Reading a text message is not available
while driving.
● Depending on the type of Bluetooth®
phone being connected, it may be
necessary to perform additional steps on
the phone.
● Messages are displayed in the
appropriate
connected
Bluetooth®
phone’s registered mail address folder.
Select the tab of the desired folder to be
displayed.
● Only received messages on the
connected Bluetooth® phone can be
displayed.
● The text of the message is not displayed
while driving.
● Turn the “PWR·VOL” knob, or use the
volume control switch on the steering
wheel to adjust the message read out
volume.
REPLYING TO A MESSAGE
(QUICK REPLY)
15 messages have already been
stored.
1
Display the message inbox screen.
(P.163)
2
Select the desired message from the
list.
3
Select “Quick Message”.
7
Select the desired message.
PHONE
4
5
Select “Send”.
 While the message is being sent, a sending message screen is displayed.
 To cancel sending the message, select
“Cancel”.
INFORMATION
● Depending on the type of Bluetooth®
phone, reply function is not available.
165
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
■EDITING QUICK REPLY MESSAGES
This operation cannot be performed
while driving.
1
Select “Quick Message”.
CALLING THE MESSAGE
SENDER
Calls can be made to an e-mail/SMS/
MMS message sender’s phone number.
This operation can be performed while
driving.
■CALLING FROM E-MAIL/SMS/MMS
MESSAGE DISPLAY
2
Select
corresponding to the desired message to edit.
3
Select “OK” when editing is completed.
1
Display the message inbox screen.
(P.163)
2
Select the desired message.
3
Select
.
INFORMATION
● To reset the editquick reply messages,
select “Default”.
● “Quick Message 1” (“I am driving and
will arrive in approximately [ETA]
minutes.”):
This message cannot be edited and will
automatically fill in [ETA] with the
navigation calculated estimated time of
arrival on the confirm message screen.
If there are waypoints set, [ETA] to the
next waypoint will be shown.
If there is no route currently set in the
navigation system, “Quick Message 1”
cannot be selected.
166
 If there are 2 or more phone numbers,
select the desired number.
4
Check that the “Call” screen is displayed.
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
■CALLING FROM A NUMBER WITHIN A MESSAGE
Calls can be made to a number identified in a message’s text area.
■CALLING FROM THE INCOMING
MESSAGE SCREEN
P.164
This operation cannot be performed
while driving.
1
Display the message inbox screen.
(P.163)
2
3
Select the desired message.
Select the text area.
7
PHONE
4
Select the desired number.
 Identified phone numbers contained in the
message are displayed.
5
Check that the “Call” screen is displayed.
INFORMATION
● A series of numbers may be recognized
as a phone number. Additionally, some
phone numbers may not be recognized,
such as those for other countries.
167
2. SETUP
1. PHONE/MESSAGE SETTINGS
1
Press the “APPS” button.
2
3
4
DISPLAYING THE PHONE/
MESSAGE SETTINGS SCREEN
IN A DIFFERENT WAY
Select “Setup”.
Select “Phone”.
Select the item to be set.
PHONE/MESSAGE SETTINGS
SCREEN
No.
Information
Registering/connecting
phone
Page
a
Sound settings
Contact/call
tings
168
history
44
169
set-
170
Messaging settings
178
Phone display settings
179
1
Display the
(P.154)
2
Select “Settings”.
phone
top
screen.
2. SETUP
“Sound Settings” SCREEN
The call and ringtone volume can be
adjusted. A ringtone can be selected.
1
2
3
Display the “Phone/Message Settings”
screen. (P.168)
Select “Sound Settings”.
Select the desired item to be set.
No.
Function
Select to set the desired ringtone.
Select “-” or “+” to adjust the ringtone volume.
Select “-” or “+” to adjust the message readout volume.
Select to set the desired incoming
SMS/MMS tone.
Select “-” or “+” to adjust the incoming SMS/MMS tone volume.
Select to set the desired incoming email tone.
Select “-” or “+” to adjust the incoming e-mail tone volume.
Select “-” or “+” to adjust the default volume of the other party’s
voice.
7
PHONE
Select to reset all setup items.
INFORMATION
● Depending on the type of phone, certain
functions may not be available.
169
2. SETUP
“Contact/Call History
Settings” SCREEN
No.
Function
Page
For PBAP compatible
Bluetooth® phones, select
to set automatic contact/
history transfer on/off.
When set to on, the
phone’s contact data and
history are automatically
transferred.

Select to update contacts
from the connected phone.
171
Select to sort contacts by
the first name or last name
field.

Select to add contacts to
the favorites list.
175
Select to delete contacts
from the favorites list.
177
Select to set the transferred contact image display on/off.

*
Select to clear contacts
from the call history.

*
Select to add new contacts
to the contact list.
172
*
Select to edit contacts in
the contact list.
173
*
Select to delete contacts
from the contact list.
174
Select to reset all setup
items.

The contact can be transferred from a
Bluetooth® phone to the system. The
contact also can be added, edited and
deleted.
The call history can be deleted and
contact and favorites can be changed.
1
Display the “Phone/Message Settings”
screen. (P.168)
2
Select “Contact/Call History Settings”.
3
Select the desired item to be set.
*: For PBAP compatible Bluetooth®
phones, this function is available when
“Automatic Transfer” is set to off.
(P.170)
170
2. SETUP
■FOR PBAP INCOMPATIBLE BUT
INFORMATION
● Depending on the type of phone, certain
functions may not be available.
● Contact data is managed independently
for every registered phone. When one
phone is connected, another phone’s
registered data cannot be read.
UPDATE CONTACTS FROM
PHONE
If your cellular phone is neither PBAP
nor OPP compatible, the contacts cannot be transferred.
COMPATIBLE
®
Bluetooth PHONES
1
Select “Update
Phone”.
Contacts
This operation cannot be performed
while driving.
1
Select “Update
Phone”.
2
Transfer the contact data to the system
Contacts
from
from
 This operation may be unnecessary
depending on the type of cellular phone.
 Depending on the type of cellular phone,
OBEX authentication may be required
when transferring contact data. Enter
“1234” into the Bluetooth® phone.
 To cancel this function, select “Cancel”.
3
Select “Done” when it appears on the
screen.
4
Check that a confirmation screen is
displayed when the operation is complete.
 Contacts are transferred automatically.
2
Check that a confirmation screen is
displayed when the operation is complete.
 This operation may be unnecessary
depending on the type of cellular phone.
 Depending on the type of cellular phone,
OBEX authentication may be required
when transferring contact data. Enter
“1234” into the Bluetooth® phone.
 If another Bluetooth® device is connected
when transferring contact data, depending
on the phone, the connected Bluetooth®
device may need to be disconnected.
 Depending on the type of Bluetooth®
phone being connected, it may be necessary to perform additional steps on the
phone.
171
7
PHONE
PBAP
Bluetooth®
using a Bluetooth® phone.
Operation methods differ between
PBAP compatible and PBAP incompatible but OPP compatible Bluetooth®
phones.
■FOR
OPP COMPATIBLE
PHONES
2. SETUP
■UPDATING THE CONTACTS IN A
REGISTERING A NEW
CONTACT TO THE CONTACT
LIST
DIFFERENT WAY (FROM THE “Call
History” SCREEN)
For PBAP compatible Bluetooth®
phones, this function is available when
“Automatic Transfer” is set to off.
(P.170)
1
Display the
(P.154)
2
Select the “Call History” tab and select a contact not yet registered in the
contact list.
phone
top
screen.
3
4
Select “Update Contact”.
5
Select a phone type for the phone
number.
172
Select the desired contact.
New contact data can be registered.
Up to 4 numbers per person can be
registered. For PBAP compatible
Bluetooth® phones, this function is
available when “Automatic Transfer” is
set to off. (P.170)
1
2
3
Select “New Contact”.
4
Select the phone type for the phone
number.
5
To add another number to this contact,
select “Yes”.
Enter the name and select “OK”.
Enter the phone number and select
“OK”.
2. SETUP
■REGISTERING A NEW CONTACT IN
A DIFFERENT WAY (FROM THE
“Call History” SCREEN)
1
Display the
(P.154)
2
Select the “Call History” tab and select a contact not yet registered in the
contact list.
3
4
phone
top
screen.
EDITING THE CONTACT DATA
For PBAP compatible Bluetooth®
phones, this function is available when
“Automatic Transfer” is set to off.
(P.170)
1
2
Select “Edit Contacts”.
3
Select
corresponding to the desired name or number.
Select the desired contact.
Select “Add to Contacts”.
Follow the steps in “REGISTERING A
NEW CONTACT TO THE CONTACT
LIST” from “STEP 2”. (P.172)
7
4
Follow the steps in “REGISTERING A
NEW CONTACT TO THE CONTACT
LIST” from “STEP 2”. (P.172)
For editing the number
4
Follow the steps in “REGISTERING A
NEW CONTACT TO THE CONTACT
LIST” from “STEP 3”. (P.172)
173
PHONE
For editing the name
2. SETUP
■EDITING THE CONTACT IN A DIF-
DELETING THE CONTACT
DATA
FERENT WAY (FROM THE “Contact
Details” SCREEN)
1
Display the
(P.154)
2
Select the “Contacts”, “Call History”
tab or the “Favorites” tab and select
the desired contact.
3
phone
top
screen.
Select “Edit Contact”.
For PBAP compatible Bluetooth®
phones, this function is available when
“Automatic Transfer” is set to off.
(P.170)
1
2
Select “Delete Contacts”.
3
Select “Yes” when the confirmation
screen appears.
Select the desired contact and select
“Delete”.
INFORMATION
● Multiple data can be selected and
deleted at the same time.
“E-mail Addresses”: Select to display all
registered e-mail addresses for the contact.
4
174
Follow the steps in “EDITING THE
CONTACT DATA” from “STEP 3”.
(P.173)
2. SETUP
■DELETING THE CONTACT IN A DIFFERENT WAY (FROM THE “Contact
Details” SCREEN)
1
Display the
(P.154)
2
Select the “Contacts”, “Call History”
tab or the “Favorites” tab and select
the desired contact.
3
4
phone
top
screen.
Select “Delete Contact”.
FAVORITES LIST SETTING
Up to 15 contacts (maximum of 4 numbers per contact) can be registered in
the favorites list.
■REGISTERING THE CONTACTS IN
THE FAVORITES LIST
1
2
Select “Yes” when the confirmation
screen appears.
Select “Add Favorite”.
Select the desired contact to add to the
favorites list.
INFORMATION
● When a Bluetooth® phone is deleted,
the contact data will be deleted at the
same time.
7
3
Check that a confirmation screen is
displayed when the operation is complete.
175
PHONE
 Dimmed contacts are already stored as a
favorite.
2. SETUP
When 15 contacts have already been
registered to the favorites list
1
When 15 contacts have already been
registered to the favorites list, a registered contact needs to be replaced.
Select “Yes” when the confirmation
screen appears to replace a contact.
2
Select the contact to be replaced.
3
Check that a confirmation screen is
displayed when the operation is complete.
Registering contacts in the favorites list
in a different way (from the “Contacts”
screen)
1
Display the
(P.154)
2
3
Select the “Contacts” tab.
phone
top
screen.
Select  at the beginning of the desired contact list name to be registered
in the favorites list.
 When selected,  is changed to , and
the contact is registered in the favorites
list.
Registering contacts in the favorites list
in a different way (from the “Contact Details” screen)
176
1
Display the
(P.154)
2
Select the “Contacts” tab or the “Call
History” tab and select the desired
contact.
3
4
Select “Add Favorite”.
phone
top
screen.
Check that a confirmation screen is
displayed when the operation is complete.
2. SETUP
■DELETING THE CONTACTS IN THE
FAVORITES LIST
1
2
Select “Remove Favorite”.
Select the desired contacts and select
“Remove”.
Select “Yes” when the confirmation
screen appears.
4
Check that a confirmation screen is
displayed when the operation is complete.
1
Display the
(P.154)
2
3
Select the “Contacts” tab.
phone
top
screen.
Select  at the beginning of the contact list name to be deleted from the favorites list.
, and
7
Deleting contacts in the favorites list in a
different way (from the “Contact Details”
screen)
PHONE
3
Deleting contacts in the favorites list in a
different way (from the “Contacts”
screen)
 When selected,  is changed to
the data is deleted from the list.
1
Display the
(P.154)
2
Select the “Contacts”, “Call History”
tab or the “Favorites” tab and select
the desired contact to delete.
3
4
Select “Remove Favorite”.
5
Check that a confirmation screen is
displayed when the operation is complete.
phone
top
screen.
Select “Yes” when the confirmation
screen appears.
177
2. SETUP
“Messaging Settings”
SCREEN
1
Display the “Phone/Message Settings”
screen. (P.168)
2
3
Select “Messaging Settings”.
Select the desired item to be set.
No.
Function
Select to set automatic message
transfer on/off.
Select to set automatic message
readout on/off.
Select to set the SMS/MMS notification popup on/off.
Select to set the e-mail notification
popup on/off.
Select to set adding the vehicle signature to outgoing messages on/off.
Select to set updating message read
status on phone on/off.
Select to change the incoming SMS/
MMS display.
“Full Screen”: When an SMS/MMS
message is received, the incoming
SMS/MMS display screen is displayed and can be operated on the
screen.
“Drop-down”: When an SMS/MMS
message is received, a message is
displayed on the upper side of the
screen.
Select to change the incoming e-mail
display.
“Full Screen”: When an e-mail is received, the incoming e-mail display
screen is the displayed and can be
operated on the screen.
“Drop-down”: When an e-mail is received, a message is displayed on the
upper side of the screen.
Select to set display of messaging account names on the inbox tab on/off.
When set to on, messaging account
names used on the cellular phone will
be displayed.
Select to reset all setup items.
178
2. SETUP
INFORMATION
● Depending on the phone, these functions may not be available.
DISPLAYING THE “Messaging
Settings” SCREEN IN A
DIFFERENT WAY
1
Display the
(P.154)
2
3
Select “Settings”.
phone
top
“Phone Display Settings”
SCREEN
1
Display the “Phone/Message Settings”
screen. (P.168)
2
3
Select “Phone Display Settings”.
Select the desired item to be set.
screen.
Select “Messaging Settings”.
No.
Function
Select to set display of the contact/
history transfer completion message
on/off.
Select to reset all setup items.
INFORMATION
● Depending on the phone, these functions may not be available.
179
7
PHONE
Select to change the incoming call
display.
“Full Screen”: When a call is received, the hands-free screen is displayed and can be operated on the
screen.
“Drop-down”: A message is displayed on the upper side of the
screen.
3. WHAT TO DO IF...
1. TROUBLESHOOTING
If there is a problem with the hands-free system or a Bluetooth® device, first check
the table below.
When using the hands-free system with a Bluetooth® device
Page
Symptom
Likely cause
The connected device may not be a
compatible
The hands-free sys-
Bluetooth® cellular
phone.
tem or Bluetooth® device does not work.
The Bluetooth® version of the connected cellular phone
may be older than
the specified version.
180
Solution
For a list of specific
devices
which
operation has been
confirmed
on
this
system, check with
your Toyota dealer or
the following website:
http://www.toyota.com/
entune/
Cellular
phone
This
system



42
Use a cellular phone
with Bluetooth® version 2.0 or higher (recommended: Ver. 3.0
+EDR or higher).
3. WHAT TO DO IF...
When registering/connecting a cellular phone
Page
Symptom
A cellular phone cannot be registered.
Solution
An incorrect passcode was entered
on
the
cellular
phone.
Cellular
phone
This
system
Enter the correct passcode on the cellular
phone.


The registration operation has not been
completed on the
cellular phone side.
Complete the registration operation on the
cellular phone (approve registration on
the phone).


Old registration information remains
on either this system or the cellular
phone.
Delete the existing registration
information
from both this system
and the cellular phone,
then register the cellular phone you wish to
connect to this system.

46
Another Bluetooth®
device is already
connected.
Manually connect the
cellular phone you wish
to use to this system.

47
Bluetooth® function
is not enabled on
the cellular phone.
Enable the Bluetooth®
function on the cellular
phone.



51
Set
Automatic
“Unable
to
Please check
phone.”
dial.
your
7
PHONE
A Bluetooth® connection cannot be made.
Likely cause
automatic
Bluetooth® connection on this system
is set to off.
Bluetooth® connection
on this system to on
when the power switch
is in ACCESSORY or
ON mode.
Bluetooth® function
is not enabled on
the cellular phone.
Enable the Bluetooth®
function on the cellular
phone.


Old registration information remains
on either this system or the cellular
phone.
Delete the existing registration
information
from both this system
and the cellular phone,
then register the cellular phone you wish to
connect to this system.

46
181
3. WHAT TO DO IF...
When making/receiving a call
Page
Symptom
A call cannot
made/received.
be
Likely cause
Solution
Your vehicle is in a
“No Service” area.
Move to where “No
Service” no longer appears on the display.
Cellular
phone
This
system


When using the phonebook
Page
Symptom
Phonebook data cannot be transferred
manually/automatically.
Phonebook data cannot be edited.
182
Likely cause
Solution
The profile version
of the connected
cellular phone may
not be compatible
with
transferring
phonebook data.
Cellular
phone
This
system
For a list of specific
devices
which
operation has been
confirmed
on
this
system, check with
your Toyota dealer or
the following website:
http://www.toyota.com/
entune/


Automatic contact
transfer function on
this system is set to
off.
Set automatic contact
transfer function on this
system to on.

170
Passcode has not
been entered on the
cellular phone.
Enter the passcode on
the cellular phone if requested (default passcode: 1234).


Transfer operation
on
the
cellular
phone has not completed.
Complete transfer operation on the cellular
phone (approve transfer operation on the
phone).


Automatic contact
transfer function on
this system is set to
on.
Set automatic contact
transfer function on this
system to off.

170
3. WHAT TO DO IF...
When using the Bluetooth® message function
Page
Symptom
Messages cannot be
viewed.
New message notifications are not displayed.
Likely cause
Solution
Message transfer is
not enabled on the
cellular phone.
Cellular
phone
This
system
Enable message transfer on the cellular
phone (approve message transfer on the
phone).


Automatic transfer
function on this system is set to off.
Set automatic transfer
function on this system
to on.

178
Notification of SMS/
MMS/E-mail reception on this system
is set to off.
Set notification of SMS/
MMS/E-mail reception
on this system to on.

178
Automatic message
transfer function is
not enabled on the
cellular phone.
Enable
automatic
transfer function on the
cellular phone.


7
PHONE
183
3. WHAT TO DO IF...
In other situations
Page
Symptom
Likely cause
Solution
The Bluetooth® connection status is displayed at the top of
the screen each time
the power switch is in
ACCESSORY or ON
mode.
Connection confirmation display on
this system is set to
on.
The cellular phone
is not close enough
to this system.
Even though all conceivable
measures
have been taken, the
symptom status does
not change.
Cellular
phone
This
system
To turn off the display,
set connection confirmation display on this
system to off.

50
Bring
the
cellular
phone closer to this
system.


Turn the cellular phone
off, remove and reinstall the battery pack,
and then restart the
cellular phone.




Stop
the
cellular
phone’s security software and close all applications.


Before using an application installed on the
cellular phone, carefully check its source and
how its operation might
affect this system.


Enable
The cellular phone
is the most likely
cause of the symptom.
the
cellular
phone’s
Bluetooth®
connection.
: For details, refer to the owner’s manual that came with the cellular phone.
184
3. WHAT TO DO IF...
7
PHONE
185
8
NAVIGATION SYSTEM
1
BASIC OPERATION
1. QUICK REFERENCE ................... 188
MAP SCREEN ..................................... 188
2
DESTINATION SEARCH
1. DESTINATION SEARCH
SCREEN .................................... 204
NAVIGATION OPTIONS SCREEN...... 190
2. SEARCH OPERATION................ 206
2. MAP SCREEN OPERATION ....... 191
SELECTING SEARCH AREA .............. 207
CURRENT POSITION DISPLAY ......... 191
SETTING HOME AS
DESTINATION................................... 207
MAP SCALE ........................................ 191
ORIENTATION OF THE MAP ............. 192
SWITCHING THE MAP MODE............ 193
SCREEN SCROLL OPERATION ........ 195
ADJUSTING LOCATION IN
SMALL INCREMENTS...................... 196
3. MAP SCREEN
INFORMATION .......................... 197
SETTING PRESET DESTINATIONS
AS DESTINATION............................. 207
SEARCHING BY ADDRESS................ 208
SEARCHING BY POINT OF
INTEREST ......................................... 209
SEARCHING FROM PREVIOUS
DESTINATIONS ................................ 212
SEARCHING BY ADDRESS BOOK .... 212
DISPLAYING MAP INFORMATION .... 197
SEARCHING BY EMERGENCY .......... 213
DISPLAYING INFORMATION
ABOUT THE ICON WHERE
THE CURSOR IS SET ...................... 199
SEARCHING BY INTERSECTION
AND FREEWAY ................................ 213
STANDARD MAP ICONS .................... 200
SEARCHING BY COORDINATES....... 215
4. TRAFFIC INFORMATION ............ 201
3. STARTING ROUTE
GUIDANCE................................ 216
DISPLAYING TRAFFIC
INFORMATION ON THE MAP.......... 203
SEARCHING BY MAP ......................... 215
STARTING ROUTE GUIDANCE.......... 216
PAUSING GUIDANCE ......................... 219
186
8
1
NAVIGATION SYSTEM
2
3
ROUTE GUIDANCE
1. ROUTE GUIDANCE SCREEN..... 220
SCREEN FOR ROUTE GUIDANCE ... 220
5
3
1. DETAILED NAVIGATION
SETTINGS................................. 240
DURING FREEWAY DRIVING............ 222
5
2. TRAFFIC SETTINGS................... 244
TURN LIST SCREEN .......................... 224
SCREEN FOR TRAFFIC
SETTINGS ........................................ 244
TURN-BY-TURN ARROW
SCREEN ........................................... 224
AUTO AVOID TRAFFIC....................... 245
6
MY TRAFFIC ROUTES ....................... 246
7
2. TYPICAL VOICE GUIDANCE
PROMPTS.................................. 225
3. EDITING ROUTE ......................... 226
4
SCREENS FOR NAVIGATION
SETTINGS ........................................ 240
ROUTE OVERVIEW............................ 221
WHEN APPROACHING
INTERSECTION ............................... 223
SETUP
TIPS FOR THE NAVIGATION
SYSTEM
8
1. GPS (GLOBAL POSITIONING
SYSTEM)................................... 250
9
6
ADDING DESTINATIONS ................... 227
REORDERING DESTINATIONS......... 227
DELETING DESTINATIONS ............... 227
SETTING ROUTE PREFERENCES ... 228
LIMITATIONS OF THE
NAVIGATION SYSTEM..................... 250
SELECTING ROUTE TYPE ................ 228
DETOUR SETTING ............................. 229
STARTING FROM ADJACENT
ROAD................................................ 230
2. MAP DATABASE VERSION
AND COVERED AREA ............. 252
MAP INFORMATION ........................... 252
ABOUT THE MAP DATA ..................... 253
4
MEMORY POINTS
1. MEMORY POINTS SETTINGS .... 231
SETTING UP HOME ........................... 232
SETTING UP PRESET
DESTINATIONS................................ 233
SETTING UP ADDRESS BOOK ......... 235
SETTING UP AREAS TO AVOID........ 237
DELETING PREVIOUS
DESTINATIONS................................ 239
187
1. BASIC OPERATION
1. QUICK REFERENCE
MAP SCREEN
To display this screen, press the “APPS” button, then select “Navigation” on the
“Apps” screen.
No.
188
Name
Function
Page
2D North-up, 2D
heading-up or 3D
heading-up symbol
Indicates whether the map orientation is set to
north-up or heading-up. The letter(s) beside this
symbol indicate the vehicle’s heading direction
(e.g. N for north). In 3D map, only a heading-up
view is available.
192
Options button
Select to display the “Navigation Options” screen.
190
“GPS” mark
(Global Positioning System)
Shows that the vehicle is receiving signals from
the GPS.
250
Traffic indicator
Shows that traffic information is received. Select
to start voice guidance for traffic information.
When traffic information is received via HD Radio
broadcast, HD mark is displayed on the right.
201
Scale indicator
This figure indicates the map scale.
191
1. BASIC OPERATION
No.
Name
Function
Page
Zoom in/out button
Select to magnify or reduce the map scale. When
either button is selected, the map scale indicator
bar appears at the bottom of the screen.
191
Footprint
button
Select to display the footprint map screen.
192
Current position
button/voice
guidance button
 Select to display the current position address.
 Select to repeat voice guidance.
225
Destination
ton
Select to display the “Destination” screen.
204
Speed limit icon
Indicates the speed limit on the current road. The
display of the speed limit icon can be set to on/off.
197
Route information bar
Displays the current street name, or the distance
with the estimated travel time/arrival time to the
destination. The route information bar fills from
left to right as the vehicle progresses on the
route.
220
Route information button
Select to change the display between the current
street name and the distance with the estimated
travel/arrival time.
220
map
but-
8
NAVIGATION SYSTEM
189
1. BASIC OPERATION
NAVIGATION OPTIONS SCREEN
The navigation options allow you to change map configurations, display/hide POI
icons, and edit the navigation routes. To display the “Navigation Options” screen,
press the “APPS” button, select “Navigation” on the “Apps” screen, and select
“Options” on the map screen.
No.
190
Function
Page
Select to display the desired map configuration.
193
Select to set display of the map information such as POI icons, route
trace, speed limit, etc.
197
Select to display the map version and coverage area.
252
Select to edit the set route.
226
Select to pause or resume route guidance.
219
Select to display the overview of the entire route.
221
1. BASIC OPERATION
2. MAP SCREEN OPERATION
CURRENT POSITION
DISPLAY
1
Press the “APPS” button.
MAP SCALE
1
Select
or
to change the
scale of the map screen.
 The scale indicator bar appears at the bottom of the screen.
2
3
Select “Navigation”.
Check that the current position map is
displayed.
 Select and hold
or
to continue changing the scale of the map
screen.
 The scale of the map screen can also be
changed by selecting the scale bar
directly. This function is not available while
driving.
8
INFORMATION
able the map scale changes from
to
when at the minimum range.
INFORMATION
● While driving, the current position mark
is fixed on the screen and the map
moves.
● The current position is automatically set
as the vehicle receives signals from the
GPS (Global Positioning System). If the
current position is not correct, it is automatically corrected after the vehicle
receives signals from the GPS.
● After the 12-volt battery disconnection,
or on a new vehicle, the current position
may not be correct. As soon as the system receives signals from the GPS, the
correct current position is displayed.
191
NAVIGATION SYSTEM
 To correct the current position manually:P.242
● The map scale is displayed above the
zoom in button at the bottom left of the
screen.
● In areas where the footprint map is avail-
1. BASIC OPERATION
FOOTPRINT MAP
For areas covered by the footprint map
(some major cities), a footprint map on
a scale of 75 ft. (25 m) can be selected.
When the map is scaled down to 150 ft.
(50 m),
changes to
and
can be selected to display the footprint
map.
1
2
Select
ORIENTATION OF THE MAP
The orientation of the map can be
changed between 2D north-up, 2D
heading-up and 3D heading-up by selecting the orientation symbol displayed at the top left of the screen.
1
Select
,
North-up screen
on the map screen.
Check that the footprint map is displayed.
Heading-up screen
 To return to the normal map display, select
.
INFORMATION
● If the map or the current position is
moved to the area which is not covered
by the footprint map, the screen scale
automatically changes to 150 ft. (50 m).
● On the footprint map, a one way street is
displayed by
.
● Scrolling on the footprint map is not
available while driving.
Building footprints in the database
were created and provided by HERE.
192
or
.
1. BASIC OPERATION
3D screen
SWITCHING THE MAP MODE
1
Select “Options” on the map screen.
2
3
Select “Map Mode”.
Select the desired configuration button.
: North-up symbol
Regardless of the direction of vehicle travel, north is always up.
: Heading-up symbol
The direction of vehicle travel is always up.
: 3D Heading-up symbol
The direction of vehicle travel is always up.
 The letter(s) beside this symbol indicate
the vehicle’s heading direction (e.g. N for
north).
No.
Function
Page
Select to display the single
map screen.
194
Select to display the dual
map screen.
194
Select to display the compass mode screen.
195
Select to display the turn list
screen.
224
Select to display the freeway exit list screen.
222
Select to display the intersection guidance screen or
the guidance screen on the
freeway.
223
Select to display the turnby-turn arrow screen.
224
8
193
NAVIGATION SYSTEM
 Depending on the conditions, certain
screen configuration buttons cannot be
selected.
1. BASIC OPERATION
■MAP ONLY
Editing right map
The right side map can be edited.
1
2
Select any point on the right side map.
Select the desired item.
■DUAL MAP
No.
 The map on the left is the main map.
Function
Page
Select to change the orientation of the map.
192
Select to display POI icons.
197
Select to show traffic information.
201
Select to change the map
scale.
191
 When set to on, the indicator will illuminate.
194
1. BASIC OPERATION
■COMPASS
Information about the destination, current position and a compass is displayed on the screen.
SCREEN SCROLL
OPERATION
Use the scroll feature to move the desired point to the center of the screen
for looking at a point on the map that is
different from the current position.
INFORMATION
● The destination mark is displayed in the
direction of the destination. When driving, refer to the longitude and latitude
coordinates, and the compass, to make
sure that the vehicle is headed in the
direction of the destination.
● When the vehicle travels out of the coverage area, the guidance screen
changes to the whole compass mode
screen.
No.
Information/Function
Cursor mark
Distance from the current position to
the cursor mark.
8
Select to register as a memory point.
To change the icon, name, etc.:
P.235
Select to return to the current position.
 To scroll over the map screen, place the
cursor mark in the desired position and
then touch and hold the map screen. The
map will continue scrolling in that direction
until the finger is released.
195
NAVIGATION SYSTEM
Select to set as a destination.
When selecting “Go to
” on the
following map screen, the navigation
system performs a search for the
route. (P.216)
If a destination has already been set,
“Go to ” and “Add to Route” will
be displayed.
“Go to ”: Select to delete the existing destination(s) and set a new
one.
“Add to Route”: Select to add a
destination.
1. BASIC OPERATION
ADJUSTING LOCATION IN
SMALL INCREMENTS
The cursor location can be adjusted in
small increments when “Adjust Location” is selected on the setting map
screen.
Also, when changing the location of
memory points on the editing screen
(P.237) and adjusting the current position mark manually on the “Calibration”
screen (P.242), 8 directional arrows
may appear for this purpose.
1
196
Select one of the 8 directional arrows
to move the cursor to the desired point
and then select “OK”.
1. BASIC OPERATION
3. MAP SCREEN INFORMATION
SELECTING THE POI ICONS
DISPLAYING MAP
INFORMATION
Information such as POI icons, route
trace, speed limit, etc. can be displayed on the map screen.
1
2
3
1
Display the “Map Information” screen.
(P.197)
2
Select “Select POI”.
Select “Options” on the map screen.
 When the POI icons to be displayed on
the map screen have already been set,
“Change POI” is displayed.
Select “Map Information”.
3
Select the desired items to be displayed.
Select the desired POI category and
select “OK”.
No.
No.
Page
Select to display the selected POI icons.

Page
Displays up to 5 selected
POI icons on the map
screen


8
Select to select or change
POI icons.
197
Select to cancel the selected POI icons.
Select
trace.
Displays up to 6 POI icons
as favorite POI categories
241
199
Select to display other POI
categories if the desired
POIs cannot be found on
the screen.
198
Select to search for the
nearest POIs.
198
to
display
route
Select to display speed limit
icon.

Select to display traffic information.
201
 When set to on, the indicator will illuminate.
197
NAVIGATION SYSTEM
Function
Information/Function
1. BASIC OPERATION
■SELECTING OTHER POI ICONS TO
■DISPLAYING THE LOCAL POI LIST
BE DISPLAYED
1
2
Select “Other POIs”.
Select the desired POI categories and
select “OK”.
“List All Categories”: Select to display all
POI categories. To add more POI categories, select “More”.
POIs that are within 20 miles (32 km) of
the current position will be listed from
among the selected categories.
1
2
Select “Find Local POI”.
Select the desired POI.
“Near...”: Select to search for POIs near
the current position or along the route.
3
Check that the selected POI is displayed on the map screen. (P.195)
When “Near...” is selected
1
Select the desired item.
“Near Here”: Select to search for POIs
near the current position.
“Along My Route”: Select to search for
POIs along the route.
198
1. BASIC OPERATION
ROUTE TRACE
The traveled route can be stored and
retraced on the map screen. This feature is available when the map scale is
30 miles (50 km) or less.
1
Display the “Map Information” screen.
(P.197)
2
Select “Route Trace”.
 The “Route Trace” indicator illuminates
and the route trace starts.
3
Check that the traveled line is displayed.
When the cursor is placed over an icon
on the map screen, the name bar is
displayed on the upper part of the
screen. If “Info” appears on the right
side of the name bar, detailed information can be displayed.
1
2
Place the cursor over an icon.
Select “Info”.
8
POI information
NAVIGATION SYSTEM
■STOP RECORDING THE ROUTE
DISPLAYING INFORMATION
ABOUT THE ICON WHERE
THE CURSOR IS SET
TRACE
1
2
Select “Route Trace” again.
A confirmation screen will be displayed.
“Yes”: Select to keep the recorded
route trace.
“No”: Select to erase the recorded
route trace.
Memory point information
INFORMATION
● The traveled route can be stored up to
124 miles (200 km).
199
1. BASIC OPERATION
Destination information
STANDARD MAP ICONS
Icon
Name
Island
Park
No.
Function
Industry
Select to register as a memory point.
To change the icon, name, etc.:
P.235
Business facility
Select to set as a destination.
Airport
Select to call the registered number.
Select to delete destination or memory point.
Select to display the edit memory
point screen.
INFORMATION
● Even when traffic information is not currently being received, traffic information
and “Info” will be displayed for a while
after traffic information has been
received.
Military
University
Hospital
Stadium
Shopping mall
Golf
200
1. BASIC OPERATION
4. TRAFFIC INFORMATION
Traffic data can be received via HD
Radio broadcast or Entune App Suite
to display traffic information on the
map screen.
1
2
3
Press the “APPS” button.
DISPLAYING TRAFFIC
INFORMATION
A list of current traffic information can
be displayed along with information on
the incident’s distance and position relative to the vehicle.
1
Display the “Traffic
screen. (P.201)
2
3
Select “Traffic Event List”.
Information”
Select the desired traffic information.
“On Current Road”: Select to display traffic information for the current road.
“On Current Route”: Select to display
traffic information for the set route.
Select “Traffic”.
 When set to on, the indicator will illuminate.
Select the desired item.
4
Check that the traffic information is displayed.
8
Function
Page
Select to display a list of
current traffic information.
201
Select to display a map
with predictive traffic data.
202
Select to display traffic
along the saved routes.
202
“Detail”: Select to display detailed traffic
information.
201
NAVIGATION SYSTEM
No.
1. BASIC OPERATION
DISPLAYING PREDICTIVE
TRAFFIC INFORMATION
A map with predictive traffic data can
be displayed.
1
2
3
Display the “Traffic
screen. (P.201)
Information”
MY TRAFFIC ROUTES
Traffic information along the saved
routes can be displayed. To use this
function, it is necessary to register a
route. (P.246)
1
Display the “Traffic
screen. (P.201)
2
Select “My Traffic Routes”.
Select “Predictive Traffic Map”.
Scroll the map to the desired point and
set the time of predictive traffic information.
 If map data has been updated, a confirmation screen will be displayed. Select “OK”
or “Do Not Tell Me Again”.
3
 The time of the predictive traffic information can be displayed in 15-minute steps
up to +45 minutes.
“ ”: Moves the time forward 15 minutes.
“ ”: Moves the time back 15 minutes.
Information”
Select the desired route.
“Options”: Select to add, edit or delete
personal routes.(P.246)
 If routes have not been registered yet, a
confirmation screen will be displayed.
Select “Yes” to register the route.
4
5
Select the desired traffic information.
Check that the traffic information is displayed.
“Detail”: Select to display detailed traffic
information.
202
1. BASIC OPERATION
DISPLAYING TRAFFIC
INFORMATION ON THE MAP
1
2
3
Select “Options” on the map screen.
Select “Map Information”.
Select “Traffic Information”.
No.
Information/Function
The icons show traffic incident, road
repair, traffic obstacles, etc. Select to
display traffic information and start
voice guidance for the traffic information.
 When set to on, the indicator will illuminate.
The color of the arrow changes depending on the traffic information received.
4
The indicator is displayed as follows.
Check that the traffic information is displayed.
: Traffic information has
been received.
: Traffic information has
been received via HD Radio broadcast.
No icon: Any traffic information has
not been received.
INFORMATION
● Traffic information may take some time
to load after the system is turned on.
8
NAVIGATION SYSTEM
203
2. DESTINATION SEARCH
1. DESTINATION SEARCH SCREEN
The “Destination” screen enables to search for a destination. To display the “Destination” screen, press the “APPS” button, and select “Navigation” on the “Apps”
screen. Then select “Dest.” on the map screen.
No.
204
Function
Page
Select to search for a destination by address.
208
Select to search for a destination by point of interest.
209
Select to search for a destination from previously set destinations.
212
Select to search for a destination from a registered entry in “Address
book”.
212
Select to search for a destination by online database.
265
Select to search for a destination from emergency service points.
213
Select to search for a destination by intersection or freeway entrance/
exit.
213
Select to search for a destination by the last displayed map.
215
Select to search for a destination by coordinates.
215
Select to set a destination by home.
207
2. DESTINATION SEARCH
No.
Function
Page
Select to set a destination from preset destinations.
207
Select to delete set destinations.
227
8
NAVIGATION SYSTEM
205
2. DESTINATION SEARCH
2. SEARCH OPERATION
1
Press the “APPS” button.
2
3
4
Select “Navigation”.
5
Select “Go” when the confirm destination screen is displayed.
No.
Function
Select “Dest.”.
Select to adjust the position in smaller increments. (P.196)
Search for a destination.
Select to register as a memory point.
Select to call the registered number.
 There are different kinds of methods to
search for a destination. (P.204)
206
Select to search for the route.
(P.216)
If a destination has already been
set, “Go Directly” and “Add to
Route” will be displayed.
“Go Directly”: Select to delete the
existing destination(s) and set a new
one.
“Add to Route”: Select to add a
destination.
2. DESTINATION SEARCH
SELECTING SEARCH AREA
The selected state (province) can be
changed to set a destination from a
different state (province) by using
“Address”, “Point of Interest” or
“Intersection & Freeway”.
1
Display the
(P.206)
“Destination”
screen.
2
Select “Address”, “Point of Interest”
or “Intersection & Freeway”.
3
Select “Select State/Province” or
“Change State/Province”.
 If a state (province) has not been selected
yet, “Select State/Province” is displayed.
4
Select the desired state (province).
SETTING HOME AS
DESTINATION
To use this function, it is necessary to
register a home address. (P.232)
1
Display the
(P.206)
2
Select “Go Home”.
“Destination”
screen.
 The navigation system performs a search
for the route and the entire route map is
displayed. (P.216)
SETTING PRESET
DESTINATIONS AS
DESTINATION
To use this function, it is necessary to
register preset destinations to the
preset screen buttons (1-5). (P.233)
Display the
(P.206)
2
Select any of the preset destination
buttons (1-5).
“Destination”
screen.
 To change countries, select the “United
States”, “Canada” or “Mexico” tab.
 For map database information and
updates: P.252
 The navigation system performs a search
for the route and the entire route map is
displayed. (P.216)
207
8
NAVIGATION SYSTEM
1
2. DESTINATION SEARCH
SEARCHING BY STREET
ADDRESS
SEARCHING BY ADDRESS
There are 2 methods to search for a
destination by address.
1
Display the
(P.206)
2
3
Select “Address”.
“Destination”
screen.
Select the desired search method.
1
Select “Street Address”.
2
Enter a house number and select
“OK”.
3
4
5
6
Enter a street name and select “OK”.
Select the desired street name.
Enter a city name and select “OK”.
Select the desired city name.
 If the same address exists, the address
list screen will be displayed. Select the
desired address.
INFORMATION
No.
Function
Page
Select to search by city.
208
Select to search by street
address.
208
SEARCHING BY CITY
1
2
Select “City”.
Enter a city name and select “OK”.
“Last 5 Cities”: Select the city name from
the list of the last 5 cities.
3
4
5
6
Select the desired city name.
Enter a street name and select “OK”.
Select the desired street name.
Enter a house number and select
“OK”.
 If the same address exists, the address
list screen will be displayed. Select the
desired address.
208
● A street name can be searched using
only the body part of its name.
For example: S WESTERN AVE
• A search can be performed by entering
“S WESTERN AVE”, “WESTERN AVE”
or “WESTERN”.
2. DESTINATION SEARCH
SEARCHING BY NAME
SEARCHING BY POINT OF
INTEREST
There are 3 methods to search for a
destination by Points of Interest.
1
Display the
(P.206)
2
3
Select “Point of Interest”.
“Destination”
1
2
3
Select “Name”.
Enter a POI name and select “OK”.
Select the desired POI.
screen.
Select the desired search method.
No.
No.
Page
Select to search by name.
209
Select to search by category.
210
Select to search by phone
number.
211
Page
Select to search for POI in
the desired city.
210
Select to search for POI
from the category list.
210
 When entering the name of a specific POI,
and there are 2 or more sites with the
same name, the list screen will be displayed. Select the desired POI.
INFORMATION
● To search for a facility name using multiple search words, put a space between
each word.
209
8
NAVIGATION SYSTEM
Function
Function
2. DESTINATION SEARCH
■SELECTING A CITY TO SEARCH
1
2
Select “City”.
Enter a city name and select “OK”.
“Any City”: Select to cancel the city setting.
3
4
SEARCHING BY CATEGORY
1
2
Select “Category”.
Select the desired search point.
Select the desired city name.
Select the desired POI.
■SELECTING FROM THE CATEGORIES
1
2
Select “Category”.
No.
Select the desired category.
Function
Select to set the search point from
near the current position.
Select to search for POIs along the
set route.
Select to set the search point from
near a city center. (P.211)
Select to set the search point from
near a destination.
 If there is more than 1 detailed item of the
selected category, the detailed list will be
displayed.
3
Select the desired POI category.
“List All Categories”: Select to display all
POI categories.
3
Select the desired POI.
 If there is more than 1 detailed item of the
selected category, the detailed list will be
displayed.
“List All Categories”: Select to display all
POI categories.
“Favorite POI Categories”: Select to use
the 6 POIs that have been previously
set.(P.241)
4
210
Select the desired POI.
2. DESTINATION SEARCH
SEARCHING BY PHONE
NUMBER
INFORMATION
● The names of POIs located within
approximately 200 miles (320 km) from
the selected search point can be displayed.
When “Near a City Center in XX*” is selected
1
2
1
Select “Phone #”.
2
Enter a phone number and select
“OK”.
 If there is more than 1 site with the same
number, the list screen will be displayed.
Select “Near a City Center in XX”.
Enter a city name and select “OK”.
“Last 5 Cities”: Select the city name from
the list of the last 5 cities.
3
4
Select the desired city name.
5
Follow the steps from 3 onward in
“SEARCHING
BY
CATEGORY”.
(P.210)
INFORMATION
● If there is no match for the entered
phone number, a list of identical numbers with different area codes will be displayed.
Select “OK” when the city center map
screen is displayed.
*: XX represents the selected search area
name.
8
NAVIGATION SYSTEM
INFORMATION
● If the navigation system has never been
used, selecting the city name from “Last
5 Cities” will not be available.
211
2. DESTINATION SEARCH
SEARCHING FROM
PREVIOUS DESTINATIONS
1
Display the
(P.206)
2
3
Select “Previous Destinations”.
“Destination”
screen.
Select the desired destination.
“Previous Start Point”: Select to display
the start point map of the previous guided
route.
“Delete”: Select to delete the previous
destination. (P.239)
INFORMATION
● The previous start point and up to 100
previously set destinations are displayed
on the screen.
212
SEARCHING BY ADDRESS
BOOK
To use this function, it is necessary to
register an address book entry.
(P.235)
1
Display the
(P.206)
2
3
Select “Address Book”.
“Destination”
screen.
Select the desired address book entry.
 “Options”: Select to register or edit
address book entries. (P.235)
2. DESTINATION SEARCH
SEARCHING BY
EMERGENCY
1
2
3
4
Display the
(P.206)
“Destination”
SEARCHING BY
INTERSECTION AND
FREEWAY
screen.
Select “Emergency”.
Select the desired emergency category.
There are 2 methods to search for a
destination by Intersection & Freeway.
1
Display the
(P.206)
2
3
Select “Intersection & Freeway”.
“Destination”
screen.
Select the desired method.
Select the desired destination.
INFORMATION
● The navigation system does not guide in
areas where route guidance is unavailable. (P.251)
No.
Page
Select to search by intersection.
214
Select to search by freeway entrance/exit.
214
213
8
NAVIGATION SYSTEM
Function
2. DESTINATION SEARCH
SEARCHING BY
INTERSECTION
SEARCHING BY FREEWAY
ENTRANCE/EXIT
1
Select “Intersection”.
1
Select “Freeway Entrance / Exit”.
2
Enter the name of the first intersecting
street which is located near the destination and select “OK”.
2
Enter a freeway name and select
“OK”.
Select the desired street name.
3
4
Select the desired freeway.
3
4
Enter the name of the second intersecting street and select “OK”.
5
5
Enter a freeway entrance or exit name
and select “OK”.
Select the desired street name.
6
Select the desired entrance or exit
name.
 If the 2 streets cross at more than 1 intersection in a city, the list of intersections will
be displayed.
Select “Entrance” or “Exit”.
INFORMATION
● Be sure to use the complete name of the
freeway or highway, including the
hyphen, when entering the destination.
Freeways and interstates use an “I” (I405). US highways use the state designation before the number (CA-118).
214
2. DESTINATION SEARCH
SEARCHING BY MAP
SEARCHING BY
COORDINATES
By selecting “Map” the last displayed
location is displayed again on the map
screen. You can search for a destination from this map.
1
Display the
(P.206)
2
3
Select “Map”.
“Destination”
screen.
1
Display the
(P.206)
2
3
Select “Coordinates”.
“Destination”
screen.
Enter the latitude and longitude and
select “OK”.
Scroll the map to the desired point and
select “Go to ”.
“Adjust Location”: Select to adjust the
position in smaller increments. (P.196)
8
NAVIGATION SYSTEM
 If a destination has already been set, “Go
to
” and “Add to Route” will be displayed.
“Go to ”: Select to delete the existing
destination(s) and set a new one.
“Add to Route”: Select to add a destination.
 The navigation system performs a search
for the route and the entire route map is
displayed. (P.216)
215
2. DESTINATION SEARCH
3. STARTING ROUTE GUIDANCE
When the destination is set, the entire
route map from the current position to
the destination is displayed.
STARTING ROUTE
GUIDANCE
1
Select “OK” to start guidance.
No.
Select the desired route from 3 possible routes. (P.217)
change
the
route.
Select to display a list of the turns required to reach the destination.
(P.218)
Current position
Destination point
Type of route and its distance
Distance of the entire route
Select to start guidance.
If “OK” is selected and held until a
beep sounds, demo mode will start.
Press the “HOME” or “APPS” button to end demo mode.
216
● Be sure to obey traffic regulations and
keep road conditions in mind while driving. If a traffic sign on the road has been
changed, the route guidance may not
indicate such changed information.
INFORMATION
Information/Function
Select to
(P.218)
WARNING
● The route for returning may not be the
same as that for going.
● The route guidance to the destination
may not be the shortest route or a route
without traffic congestion.
● Route guidance may not be available if
there is no road data for the specified
location.
● When setting the destination on a map
with a scale more than 0.5 mile (800 m),
the map scale changes to 0.5 miles (800
m) automatically. If this occurs, set the
destination again.
● If a destination that is not located on a
road is set, the vehicle will be guided to
the point on a road nearest to the destination. The road nearest to the selected
point is set as the destination.
2. DESTINATION SEARCH
3 ROUTES SELECTION
■DISPLAYING 3 ROUTES INFORMATION
1
2
Select “3 Routes”.
Select the desired route.
No.
1
2
Select “Info”.
Check that the “3 Route Information”
screen is displayed.
Function
Select to display the quickest route.
No.
Information
Select to display the route that is the
shortest distance to the set destination.
Time necessary for the entire trip
Select to display the alternative
route.
Distance of the toll road
Select to display the information
about the 3 routes. (P.217)
Distance of the freeway
Distance of the entire trip
8
NAVIGATION SYSTEM
Distance of the ferry trip
217
2. DESTINATION SEARCH
DISPLAYING TURN LIST
A list of turn information from the current position to the destination can be
displayed.
1
2
Select “Turn List”.
Check that the turn list is displayed.
No.
Information
Destinations can be added, reordered
or deleted, and conditions for the route
to the destination can be changed.
1
2
Select “Edit Route”.
Select the desired item.
Function
Page
Current position
Select to add destinations.
227
Distance to the next turn
Select to delete destinations.
227
Select to reorder destinations.
227
Select to set route preferences.
228
Select to change route
type.
228
Turn direction at the intersection
Select to display the map of the selected point.
INFORMATION
● However, not all road names on the
route may appear on the list. If a road
changes its name without requiring a
turn (such as on a street that runs
through 2 or more cities), the name
change will not appear on the list. The
street names will be displayed in order
from the starting point, along with the
distance to the next turn.
218
EDITING ROUTE
No.
INFORMATION
● Even if the “Freeways” indicator is
dimmed, the route cannot avoid including a freeway in some cases. (P.228)
● If the calculated route includes a trip by
ferry, the route guidance shows a sea
route. After traveling by ferry, the current
position may be incorrect. Upon reception of GPS signals, it is automatically
corrected.
2. DESTINATION SEARCH
PAUSING GUIDANCE
1
Select “Options” on the map screen.
2
Select “Pause Guidance”.
RESUMING GUIDANCE
1
Select “Resume Guidance”.
8
NAVIGATION SYSTEM
219
3. ROUTE GUIDANCE
1. ROUTE GUIDANCE SCREEN
During the route guidance, various
types of guidance screens can be displayed depending on conditions.
SCREEN FOR ROUTE
GUIDANCE
CHANGING ROUTE
INFORMATION BAR
When the vehicle is on the guidance
route, the route information bar displays the current street name or the
distance with the estimated travel/arrival time to the destination.
1
Select the route information bar (
) or
the route information button ( ) to
change the display of the route information bar.
No.
Information/Function
Distance to the next turn and an arrow indicating the turning direction
Guidance route
Current position
Current street name or route information
INFORMATION
● If the vehicle goes off the guidance
route, the route is searched again.
● For some areas, the roads have not
been completely digitized in our database. For this reason, the route guidance may select a road that should not
be traveled on.
● When arriving at the set destination the
destination name will be displayed on
the upper part of the screen.
220
No.
Information/Function
Select to change the display between the estimated travel time and
the estimated arrival time.
Select to change the display between the current street name and
the distance with the estimated travel/arrival time.
INFORMATION
● When the vehicle is on the guidance
route, the distance measured along the
route is displayed. Travel time and
arrival time are calculated based on the
average speed for the specified speed
limit.
● When the vehicle gets off the guidance
route, the arrow facing the destination is
displayed instead of the estimated
travel/arrival time.
● The route information bar fills from left to
right as the vehicle progresses on the
route.
3. ROUTE GUIDANCE
DISTANCE AND TIME TO
DESTINATION
When driving on the guidance route
with more than 1 destination set, a list
of the distance with estimated travel/
arrival time from the current position to
each destination is displayed.
1
2
Select the route information bar.
Check that the list of the distance and
time is displayed.
ROUTE OVERVIEW
The entire route from the current position to the destination can be displayed
during the route guidance.
1
2
3
Select “Options” on the map screen.
Select “Route Overview”.
Check that the entire route map is displayed.
 For details about this screen: P.216
 By selecting one of the number buttons,
the desired route information is displayed.
8
NAVIGATION SYSTEM
221
3. ROUTE GUIDANCE
DURING FREEWAY DRIVING
During freeway driving, the freeway
exit information screen will be displayed.
No./
Icon
Information/Function
Distance and time from the current
position to the road traffic facilities.
Name of the road traffic facilities.
When the vehicle approaches an exit
or junction, the freeway guidance
screen will be displayed.
No.
Information/Function
Next exit or junction name
Distance from the current position to
the exit or junction
POIs that are close to a freeway exit.
Select to hide the freeway guidance
screen. To return to the freeway
Select to display the selected map of
the exit vicinity.
guidance screen, select
Select to display the nearest road
traffic facilities from the current position.
Select to scroll to farther road traffic
facilities.
Select to scroll to closer road traffic
facilities.
222
WHEN APPROACHING
FREEWAY EXIT OR JUNCTION
.
Remaining distance bar to the guidance point
3. ROUTE GUIDANCE
TOLLGATE GUIDANCE
When the vehicle approaches a tollgate, the tollgate view will be displayed.
No.
WHEN APPROACHING
INTERSECTION
When the vehicle approaches an intersection, the intersection guidance
screen will be displayed.
Information/Function
Distance from the current position to
the tollgate
No.
Information/Function
Next street name
Select to hide the tollgate guidance
screen. To return to the tollgate
guidance screen, select
.
Remaining distance bar to the guidance point
Distance to the intersection
Select to hide the intersection guidance screen. To return to the intersection guidance screen, select
Remaining distance bar to the guidance point
223
NAVIGATION SYSTEM
.
8
3. ROUTE GUIDANCE
TURN LIST SCREEN
1
Select “Turn List” on the “Map Mode”
screen. (P.193)
2
Check that the turn list screen is displayed.
No.
TURN-BY-TURN ARROW
SCREEN
On this screen, information about the
next turn on the guidance route can be
displayed.
1
Select “Turn-by-Turn Arrow” on the
“Map Mode” screen. (P.193)
2
Check that the turn-by-turn arrow
screen is displayed.
Information/Function
Turn direction
Distance between turns
Next street or destination name
No.
Information/Function
Exit number or street name
Turn direction
Distance to the next turn
224
3. ROUTE GUIDANCE
2. TYPICAL VOICE GUIDANCE PROMPTS
As the vehicle approaches an intersection, or point, where maneuvering the
vehicle is necessary, the system’s
voice guidance will provide various
messages.
WARNING
● Be sure to obey the traffic regulations
and keep the road condition in mind
especially when you are driving on IPD
roads. The route guidance may not have
the updated information such as the
direction of a one way street.
INFORMATION
● If a voice guidance command cannot be
heard, select
on the map screen
to hear it again.
● To adjust the voice guidance volume:
P.58
● Voice guidance may be made early or
late.
● If the system cannot determine the current position correctly, you may not hear
voice guidance or may not see the magnified intersection on the screen.
8
NAVIGATION SYSTEM
225
3. ROUTE GUIDANCE
3. EDITING ROUTE
1
Press the “APPS” button.
5
Select the item to be set.
No.
2
3
4
Function
Page
Select “Navigation”.
Select to add destinations.
227
Select “Options”.
Select to delete destinations.
227
Select to reorder destinations.
227
Select to set route preferences.
228
Select to change route
type.
228
Select to set detours.
229
Select to start from adjacent road.
230
Select “Edit Route”.
6
226
Check that the entire route map is displayed. (P.216)
3. ROUTE GUIDANCE
ADDING DESTINATIONS
1
Display the
(P.226)
2
3
Select “Add”.
4
“Edit
Route”
DELETING DESTINATIONS
screen.
Search for an additional destination in
the same way as a destination search.
(P.204)
Select “Add Destination Here” to insert the new destination into the route.
1
Display the
(P.226)
2
3
Select “Delete”.
“Edit
Route”
screen.
Select “Yes” when the confirmation
screen appears.
 When more than 1 destination has been
set, a list will be displayed on the screen.
Select the item(s) to be deleted.
“Delete All”: Select to delete all destinations on the list.
 If more than 1 destination has been set,
the system will recalculate the route(s) to
the set destination(s) as necessary.
REORDERING
DESTINATIONS
8
NAVIGATION SYSTEM
When more than 1 destination has
been set, the arrival order of the destinations can be changed.
1
Display the
(P.226)
2
3
Select “Reorder”.
“Edit
Route”
screen.
Select the desired destination and select “Move Up” or “Move Down” to
change the arrival order. Then select
“OK”.
227
3. ROUTE GUIDANCE
SETTING ROUTE
PREFERENCES
SELECTING ROUTE TYPE
The conditions to determine the route
can be selected from various choices
such as freeways, toll roads, ferries,
etc.
1
Display the
(P.226)
2
3
Select “Preferences”.
“Edit
Route”
1
Display the
(P.226)
2
3
Select “Route Type”.
“Edit Route”
screen.
Select the desired route type.
screen.
Select the desired route preferences
and select “OK”.
 During driving, the route guidance starts
after selecting the desired route type.
4
The entire route from the starting point
to the destination is displayed.
 For details about this screen: P.216
 When set to on, the indicator will illuminate.
228
3. ROUTE GUIDANCE
3
DETOUR SETTING
Select the desired detour distance.
During the route guidance, the route
can be changed to detour around a
section of the route where a delay is
caused by road repairs, an accident,
etc.
1
Display the
(P.226)
2
Select “Detour”.
“Edit
Route”
screen.
No.
Function
Select to detour within 1 mile of the
current position.
Select to detour within 3 miles of the
current position.
Select to detour within 5 miles of the
current position.
Select to detour on the entire route.
Select to make the system search
for the route based on traffic congestion information received from
traffic information. (P.201)
8
NAVIGATION SYSTEM
229
3. ROUTE GUIDANCE
INFORMATION
STARTING FROM ADJACENT
ROAD
When a freeway and a surface road
run in parallel, the system may show
the guidance route going on the freeway while driving on the surface road,
or vice versa.
● This picture shows an example of how
the system would guide around a delay
caused by a traffic jam.
This position indicates the location of a
traffic jam caused by road repairs, an
accident, etc.
This route indicates the detour suggested by the system.
● When the vehicle is on a freeway, the
detour distance selections are 5, 15 and
25 miles (or 5, 15 and 25 km if units are
in km).
● The system may not be able to calculate
a detour route depending on the
selected distance and surrounding road
conditions.
230
If this happens, you can instantly
choose the adjacent road for the route
guidance.
1
Display the “Edit Route” screen.
(P.226)
2
Select “Start from Adjacent Road”.
INFORMATION
● When there is no adjacent road, this
screen button will not be displayed.
4. MEMORY POINTS
1. MEMORY POINTS SETTINGS
Home, preset destinations, address
book entries, areas to avoid can be set
as memory points. The registered
points can be used as the destinations.
(P.204)
4
Select the desired item to be set.
Registered areas to avoid, will be
avoided when the system searches for
a route.
1
2
3
Press the “APPS” button.
Select “Setup”.
Select “Navigation”.
No.
Function
Page
Select to set home.
232
Select to set preset destinations.
233
Select to set the address
book.
235
Select to set areas to
avoid.
237
Select to delete previous
destinations.
239
8
240
NAVIGATION SYSTEM
Select to set detailed navigation settings.
231
4. MEMORY POINTS
EDITING HOME
SETTING UP HOME
If home has been registered, that information can be recalled by selecting
“Go Home” on the “Destination”
screen. (P.207)
1
Display the “Navigation
screen. (P.231)
2
3
Select “Home”.
1
2
Select “Edit”.
Select the desired item to be edited.
Settings”
Select the desired item to be set.
No.
No.
Function
Page
Select to register home.
232
Select to edit home.
232
Select to delete home.
232
3
Select “Set Home”.
3
Select “OK” when the editing home
screen appears.
232
Select the desired item to search for
the location. (P.204)
Page
Select to edit the home
name.
237
Select to set display of the
home name on/off.

Select to edit location information.
237
Select to edit the phone
number.
237
Select to change the icon
to be displayed on the map
screen.
236
Select “OK”.
DELETING HOME
REGISTERING HOME
1
2
Function
1
2
Select “Delete”.
Select “Yes” when the confirmation
screen appears.
4. MEMORY POINTS
REGISTERING PRESET
DESTINATIONS
SETTING UP PRESET
DESTINATIONS
If a preset destination has been registered, that information can be recalled
by using preset destinations on the
“Destination” screen. (P.207)
1
Display the “Navigation
screen. (P.231)
2
3
Select “Preset Destinations”.
1
Select “Set”.
2
Select the desired item to search for
the location. (P.204)
3
Select a position for this preset destination.
4
Select “OK” when the editing preset
destination screen appears. (P.234)
Settings”
Select the desired item.
INFORMATION
No.
Page
Select to register a preset
destination.
233
Select to edit a preset destination.
234
Select to delete a preset
destination.
234
8
NAVIGATION SYSTEM
Function
● Up to 5 preset destinations can be registered.
233
4. MEMORY POINTS
EDITING PRESET
DESTINATIONS
DELETING PRESET
DESTINATIONS
1
Select “Edit”.
1
Select “Delete”.
2
3
Select the desired preset destination.
2
Select the preset destination to be deleted and select “Delete”.
3
Select “Yes” when the confirmation
screen appears.
Select the item to be edited.
No.
4
234
Function
Page
Select to edit the preset
destination name.
237
Select to set display of the
preset destination name
on/off.

Select to edit location information.
237
Select to edit the phone
number.
237
Select to change the icon
to be displayed on the map
screen.
236
Select “OK”.
4. MEMORY POINTS
EDITING ADDRESS BOOK
ENTRIES
SETTING UP ADDRESS
BOOK
Points on the map can be registered.
1
Display the “Navigation
screen. (P.231)
2
3
Select “Address Book”.
Settings”
1
2
3
Select the desired item.
No.
The icon, name, location and/or phone
number of a registered address book
entry can be edited.
Page
Select to register address
book entries.
235
Select to edit address book
entries.
235
Select to delete address
book entries.
237
Select “New”.
3
Select “OK” when the editing address
book entry screen appears. (P.235)
Select the item to be edited.
No.
REGISTERING ADDRESS
BOOK ENTRIES
1
2
Select the desired address book entry.
Select the desired item to search for
the location. (P.204)
4
Function
Page
Select to edit the address
book entry name.
237
Select to set display of the
address book entry name
on/off.

Select to edit location information.
237
Select to edit the phone
number.
237
Select to change the icon
to be displayed on the map
screen.
236
Select “OK”.
INFORMATION
● Up to 100 address book entries can be
registered.
235
8
NAVIGATION SYSTEM
Function
Select “Edit”.
4. MEMORY POINTS
■CHANGING THE ICON
1
2
Select “Edit” next to the “Icon”.
Select the desired icon.
When the “With Sound” tab is selected
A sound for some address book entries
can be set. When the vehicle approaches the location of the address
book entry, the selected sound will be
heard.
1
2
Select the “With Sound” tab.
Select the desired sound icon.
: Select to play the sound.
 Change pages by selecting the “Page 1”,
“Page 2” or “With Sound” tab.
“With Sound”: Select the memory points
with a sound
 When “Bell (with Direction)” is selected,
select an arrow to adjust the direction and
select “OK”.
INFORMATION
● The bell sounds only when the vehicle
approaches this point in the direction
that has been set.
236
4. MEMORY POINTS
■CHANGING THE NAME
1
2
Select “Edit” next to “Name”.
Enter a name and select “OK”.
■CHANGING THE LOCATION
1
2
Select “Edit” next to “Location”.
Scroll the map to the desired point
(P.196) and select “OK”.
■CHANGING PHONE NUMBER
1
2
Select “Edit” next to “Phone #”.
SETTING UP AREAS TO
AVOID
Areas to be avoided because of traffic
jams, construction work or other reasons can be registered as “Areas to
Avoid”.
1
Display the “Navigation
screen. (P.231)
2
3
Select “Areas to Avoid”.
Settings”
Select the desired item.
Enter the phone number and select
“OK”.
DELETING ADDRESS BOOK
ENTRIES
1
2
Select the item to be deleted and select
“Delete”.
No.
Function
Page
Select to register areas to
avoid.
238
Select to edit areas to
avoid.
238
Select to delete areas to
avoid.
239
Select “Yes” when the confirmation
screen appears.
237
8
NAVIGATION SYSTEM
3
Select “Delete”.
4. MEMORY POINTS
REGISTERING AREAS TO
AVOID
1
Select “New”.
2
Select the desired item to search for
the location. (P.204)
3
Select either
or
to
change the size of the area to be avoided and select “OK”.
EDITING AREAS TO AVOID
The name, location and/or area size of
a registered area can be edited.
1
2
3
Select “Edit”.
Select the area and select “OK”.
Select the item to be edited.
No.
4
Select “OK” when the editing area to
avoid screen appears.
INFORMATION
● If a destination is entered in the area to
avoid or the route calculation cannot be
made without running through the area
to avoid, a route passing through the
area to be avoided may be shown.
● Up to 10 locations can be registered as
points/areas to avoid.
Page
Select to edit the name of
the area to avoid.
239
Select to set display of the
area to avoid name on/off.

Select to edit area location.
239
Select to edit area size.
239
Select to set the area to
avoid function on/off.
4
238
Function
Select “OK”.

4. MEMORY POINTS
■CHANGING THE NAME
1
2
Select “Edit” next to “Name”.
Enter a name and select “OK”.
DELETING AREAS TO AVOID
1
2
Select “Delete”.
3
Select “Yes” when the confirmation
screen appears.
■CHANGING THE LOCATION
1
2
Select “Edit” next to “Location”.
Scroll the map to the desired point
(P.196) and select “OK”.
■CHANGING THE AREA SIZE
1
Select “Edit” next to “Size”.
2
Select either
or
to
change the size of the area to be avoided and select “OK”.
Select the area to be deleted and select “Delete”.
DELETING PREVIOUS
DESTINATIONS
Previous destinations can be deleted.
1
Display the “Navigation
screen. (P.231)
2
3
Select “Delete Previous Dest.”.
Settings”
Select the previous destination to be
deleted and select “Delete”.
8
Select “Yes” when the confirmation
screen appears.
239
NAVIGATION SYSTEM
4
5. SETUP
1. DETAILED NAVIGATION SETTINGS
Settings are available for pop-up information, favorite POI categories, low
fuel warning, etc.
1
Press the “APPS” button.
2
3
4
5
6
Select “Setup”.
240
Select “Navigation”.
Select “Detailed Navi. Settings”.
Select the items to be set.
Select “OK”.
SCREENS FOR NAVIGATION
SETTINGS
5. SETUP
No.
Function
Page
Select to set the voice guidance for the next street
name on/off.

Select to set IPD road guidance on/off.

Select to set favorite POI
categories that are used for
POI selection to display on
the map screen.
241
Select to adjust the current
position mark manually or
to adjust miscalculation of
the distance caused by tire
replacement.
242
Select to set display of popup information on/off.

Select to set display of low
fuel warning on/off.
243
Select to reset all setup
items.

FAVORITE POI CATEGORIES
(SELECT POI ICONS)
Up to 6 POI icons, which are used for
selecting POIs on the map screen, can
be selected as favorites.
1
Display the “Detailed Navi. Settings”
screen. (P.240)
2
3
Select “Favorite POI Categories”.
Select the category to be changed.
“Default”: Select to set the default categories.
4
Select the desired POI icon.
241
NAVIGATION SYSTEM
“List All Categories”: Select to display all
POI categories.
5
8
Select the desired POI category.
5. SETUP
CURRENT POSITION/TIRE
CHANGE CALIBRATION
The current position mark can be adjusted manually. Miscalculation of the
distance caused by tire replacement
can also be adjusted.
1
Display the “Detailed Navi. Settings”
screen. (P.240)
2
3
Select “Calibration”.
Select the desired item.
■POSITION/DIRECTION
CALIBRA-
TION
When driving, the current position
mark will be automatically corrected by
GPS signals. If GPS reception is poor
due to location, the current position
mark can be adjusted manually.
1
2
Select “Position / Direction”.
3
Select an arrow to adjust the direction
of the current position mark and select
“OK”.
Scroll the map to the desired point
(P.196) and select “OK”.
 For additional information on the accuracy of a current position: P.250
■TIRE CHANGE CALIBRATION
The tire change calibration function will
be used when replacing the tires. This
function will adjust miscalculation
caused by the circumference difference between the old and new tires.
1
Select “Tire Change”.
 The message appears and the quick distance calibration starts automatically.
INFORMATION
● If this procedure is not performed when
the tires are replaced, the current position mark may be incorrectly displayed.
242
5. SETUP
LOW FUEL WARNING POP-UP
When the fuel level is low, a warning
message will pop up on the screen.
1
Display the “Detailed Navi. Settings”
screen. (P.240)
2
Select “Low Fuel Warning Pop-up”.
■SEARCHING GAS STATION IN LOW
FUEL WARNING
A nearby gas station can be selected
as a destination.
1
Select “Yes” when the low fuel warning appears.
2
Select the desired nearby gas station.
8
Select “Enter
tion.
NAVIGATION SYSTEM
3
” to set as a destina-
“Info”: Select to display gas station information. (P.199)
243
5. SETUP
2. TRAFFIC SETTINGS
Traffic information such as traffic congestion or traffic incident warnings can
be made available.
1
Press the “APPS” button.
2
3
4
5
Select “Setup”.
SCREEN FOR TRAFFIC
SETTINGS
Select “Traffic”.
Select the items to be set.
Select “OK”.
No.
Function
Select to set specific routes (such as
frequently used routes) on which
you wish to receive traffic information. (P.246)
Select to set the avoid traffic function auto/manual. (P.245)
Select to set the usage of traffic information for the estimated arrival
time on/off.
Select to set the display of an arrow
of free flowing traffic on/off.
Select to set to on/off whether to
consider the predictive traffic information (P.202) with estimated arrival time and detoured route
search.
Select to set of traffic incident voice
warning on/off.
Select to reset all setup items.
244
5. SETUP
AUTO AVOID TRAFFIC
1
Display the “Traffic Settings” screen.
(P.244)
2
3
Select “Avoid Traffic”.
Select the desired item.
No.
Function
Select to automatically change
routes when congestion information
of the guidance route has been received.
LY
When the navigation system calculates a new route, the following screen
will be displayed.
1
Select the desired item.
No.
Function
Select to start route guidance using
the new route.
Select to confirm the new route and
current route on the map.
8
Select to continue the current route
guidance.
Select to not reroute when congestion information for the guidance
route has been received.
4
Select “OK”.
245
NAVIGATION SYSTEM
Select to select manually whether or
not to change routes when congestion information of the guidance
route has been received. In this
mode, a screen will appear to ask if
you wish to reroute.
■CHANGING THE ROUTE MANUAL-
5. SETUP
REGISTERING PERSONAL
ROUTES
MY TRAFFIC ROUTES
Specific routes (such as frequently
used routes) on which you wish to receive traffic information can be registered as “My Traffic Routes”. A route is
set by defining a start point and end
point, and can be adjusted by setting
up to 2 preferred roads.
1
Display the “Traffic Settings” screen.
(P.244)
2
3
Select “My Traffic Routes”.
Select the desired item.
No.
Function
Page
Select to register personal
routes.
246
Select to edit personal
routes.
247
Select to delete personal
routes.
247
1
Select “New”.
2
Select “Edit” next to “Name”.
3
4
5
Enter the name and select “OK”.
6
7
Select “Edit” next to “End”.
8
Select “OK” when the editing traffic
route screen appears.
Select “Edit” next to “Start”.
Select the desired item to search for
the location. (P.204)
Select the desired item to search for
the location. (P.204)
 The routes can be adjusted by setting preferred roads. (P.248)
INFORMATION
● Up to 5 routes can be registered.
246
5. SETUP
EDITING PERSONAL ROUTES
1
2
3
DELETING PERSONAL
ROUTES
Select “Edit”.
Select the desired traffic route.
1
Select “Delete”.
2
Select the traffic route to be deleted
and select “Delete”.
3
Select “Yes” when the confirmation
screen appears.
Select “Edit” next to the item to be edited.
8
Function
Page
NAVIGATION SYSTEM
No.
Select to edit the name of
the personal route.
Select to edit start location.
246
Select to edit end location.
Select to see and modify
the entire route.
4
248
Select “OK”.
 The entire route map will be displayed.
247
5. SETUP
SETTING PREFERRED ROADS
“My Traffic Routes” can be adjusted by
setting up to 2 preferred roads.
1
Select “Set Preferred Roads”.
2
■ADDING PREFERRED ROADS
1
Select “Add”.
 If two preferred roads are already set,
select “Yes” and delete a preferred road
before add a new one.
2
Scroll the map to the desired point and
select “OK”.
3
Select “OK” to use this road.
Select the desired item.
“Next”: Select to change road.
4
No.
248
Function
Page
Select to add preferred
roads.
248
Select to modify preferred
roads.
249
Select to delete preferred
roads.
249
Select “Add Here” for the desired location.
 If a preferred road is already set, a second
preferred road can be added anywhere
between the start point, the end point and
the existing preferred road.
5. SETUP
■MODIFYING PREFERRED ROADS
■DELETING PREFERRED ROADS
1
2
Select “Modify”.
1
2
3
Scroll the map to the desired point and
select “OK”.
Select the preferred road to be modified if 2 preferred roads have been set.
Select “Delete”.
Select the preferred road to be deleted
if 2 preferred roads have been set.
“Delete All”: Select to delete all preferred
roads on the list.
3
Select “Yes” when the confirmation
screen appears.
8
NAVIGATION SYSTEM
4
Select “OK” to use this road.
“Next”: Select to change road.
249
6. TIPS FOR THE NAVIGATION SYSTEM
1. GPS (GLOBAL POSITIONING SYSTEM)
LIMITATIONS OF THE
NAVIGATION SYSTEM
This navigation system calculates the
current position using satellite signals,
various vehicle signals, map data, etc.
However, an accurate position may not
be shown depending on satellite conditions, road configuration, vehicle condition or other circumstances.
The Global Positioning System (GPS) developed and operated by the U.S. Department of Defense provides an accurate
current position, normally using 4 or more
satellites, and in some case 3 satellites.
The GPS system has a certain level of inaccuracy. While the navigation system
compensates for this most of the time, occasional positioning errors of up to 300 ft.
(100 m) can and should be expected. Generally, position errors will be corrected
within a few seconds.
250
When the vehicle is receiving signals from
satellites, the “GPS” mark appears at the
top left of the screen.
The GPS signal may be physically obstructed, leading to inaccurate vehicle position on the map screen. Tunnels, tall
buildings, trucks, or even the placement of
objects on the instrument panel may obstruct the GPS signals.
The GPS satellites may not send signals
due to repairs or improvements being
made to them.
Even when the navigation system is receiving clear GPS signals, the vehicle position may not be shown accurately or
inappropriate route guidance may occur in
some cases.
NOTICE
● The installation of window tinting may
obstruct the GPS signals. Most window
tinting contains some metallic content
that will interfere with GPS signal reception of the antenna in the instrument
panel. We advise against the use of window tinting on vehicles equipped with
navigation systems.
6. TIPS FOR THE NAVIGATION SYSTEM
 Accurate current position may not be
shown in the following cases:
• When driving on a small angled Yshaped road.
• When driving on a winding road.
• When driving on a slippery road such as
in sand, gravel, snow, etc.
• When driving on a long straight road.
• When freeway and surface streets run in
parallel.
• After moving by ferry or vehicle carrier.
• When a long route is searched during
high speed driving.
• When driving without setting the current
position calibration correctly.
• After repeating a change of direction by
going forward and backward, or turning
on a turntable in a parking lot.
• When leaving a covered parking lot or
parking garage.
• When a roof carrier is installed.
• When driving with tire chains installed.
• When the tires are worn.
• After replacing a tire or tires.
• When using tires that are smaller or
larger than the factory specifications.
• When the tire pressure in any of the 4
tires is not correct.
 After replacing a tire: P.242
INFORMATION
● This navigation system uses tire turning
data and is designed to work with factory-specified tires for the vehicle.
Installing tires that are larger or smaller
than the originally equipped diameter
may cause inaccurate display of the current position. The tire pressure also
affects the diameter of the tires, so make
sure that the tire pressure of all 4 tires is
correct.
251
8
NAVIGATION SYSTEM
 If the vehicle cannot receive GPS signals, the current position can be
adjusted manually. For information on
setting the current position calibration:
P.242
 Inappropriate route guidance may occur in
the following cases:
• When turning at an intersection off the
designated route guidance.
• If you set more than 1 destination but
skip any of them, auto reroute will display a route returning to the destination
on the previous route.
• When turning at an intersection for which
there is no route guidance.
• When passing through an intersection
for which there is no route guidance.
• During auto reroute, the route guidance
may not be available for the next turn to
the right or left.
• During high speed driving, it may take a
long time for auto reroute to operate. In
auto reroute, a detour route may be
shown.
• After auto reroute, the route may not be
changed.
• If an unnecessary U-turn is shown or
announced.
• If a location has multiple names and the
system announces 1 or more of them.
• When a route cannot be searched.
• If the route to your destination includes
gravel, unpaved roads or alleys, the
route guidance may not be shown.
• Your destination point might be shown
on the opposite side of the street.
• When a portion of the route has regulations prohibiting the entry of the vehicle
that vary by time or season or other reasons.
• The road and map data stored in the
navigation system may not be complete
or may not be the latest version.
6. TIPS FOR THE NAVIGATION SYSTEM
2. MAP DATABASE VERSION AND COVERED AREA
MAP INFORMATION
5
Check that the map data screen is displayed.
Coverage areas and legal information
can be displayed and map data can be
updated.
1
Press the “APPS” button.
No.
Function
Map version
Select to display map coverage areas.
Select to display legal information.
2
3
4
252
Select “Navigation”.
Select “Options”.
Select “Map Data”.
INFORMATION
● Map data updates are available for a
fee. Contact your Toyota dealer for further information.
6. TIPS FOR THE NAVIGATION SYSTEM
ABOUT THE MAP DATA
Map data for the navigation system is
contained in a micro SD card that is inserted in the micro SD card slot.
Do not eject the micro SD card, as doing so may deactivate the navigation
system.
NOTICE
● Do not edit or delete the map data on
the micro SD card, as doing so may
deactivate the navigation system.
8
NAVIGATION SYSTEM
INFORMATION
● microSDHC Logo is a trademark of SD3C,LLC.
253
6. TIPS FOR THE NAVIGATION SYSTEM
254
9
1
Entune App Suite
2
1
Entune App Suite OVERVIEW
3
1. Entune App Suite SERVICE ...... 256
BEFORE USING THE FUNCTION ...... 258
4
PREPARATION BEFORE USING
Entune App Suite .............................. 259
5
2
Entune App Suite OPERATION
6
1. Entune App Suite ....................... 261
USING Entune App Suite..................... 261
LINKING Entune App Suite AND
NAVIGATION FUNCTION................. 265
Entune App Suite KEYWORD
OPERATION ..................................... 266
3
SETUP
7
8
9
1. Entune App Suite SETTINGS .... 268
SCREEN FOR
Entune App Suite SETTINGS ........... 268
255
1. Entune App Suite OVERVIEW
1. Entune App Suite SERVICE*
Entune App Suite is a service that enables downloadable applications to be displayed on and operated from the screen. Before Entune App Suite can be used, a
few actions need to be performed first. (P.259)
*: Entune App Suite is available in the contiguous United States, D.C. and Alaska.
256
1. Entune App Suite OVERVIEW
No.
Name
Function
Content provider
Provides content to the system via a cellular phone.
Application server
Provides downloadable application to the system via a cellular
phone.
Cellular phone*
Using the Entune App Suite application, communication is relayed between the system, the application server and the contents provider.
Applications
Downloaded Entune App Suite applications provide access to
audio content from a content provider when connected via a
compatible phone with a data connection.
Entune App Suite
Contents received, via a cellular phone, from the contents provider servers are displayed on the screen. The system is
equipped with an application player to run applications.
*: For known compatible phones, refer to http://www.toyota.com/entune/.
INFORMATION
● The actual service availability is dependent on the network condition.
9
Entune App Suite
257
1. Entune App Suite OVERVIEW
BEFORE USING THE
FUNCTION
SUBSCRIPTION
 User registration is required to start using
the Entune App Suite service.
 Entune App Suite does not require an activation fee or monthly recurring fees.
 Services requiring a separate contract can
also be used.*
*: For details, refer to
http://www.toyota.com/entune/ or call
1-800-331-4331.
AVAILABILITY OF SERVICE
 Entune App Suite is available in the contiguous United States, D.C. and Alaska.
INFORMATION
● When using Entune App Suite, depending on the details of your cellular phone
contract, data usage fees may apply.
Confirm data usage fees before using
this service.
● In this section, the required actions to
activate applications, connect a cellular
phone to the system and registration
steps for Entune App Suite are
explained. For details regarding Entune
App Suite operations and each of the
applications, refer to
http://www.toyota.com/entune/.
● The actual service availability is dependent on the network condition.
258
INITIALIZING PERSONAL
DATA
The personal data used in applications
can be removed from the system.
(P.57)
 The following personal data can be
deleted from the system and returned to
their default settings:
• Downloaded applications
• Downloaded application content
INFORMATION
● Once initialized, data will be erased from
the system. Pay close attention when
initializing the data.
1. Entune App Suite OVERVIEW
PREPARATION BEFORE
USING Entune App Suite
USER REGISTRATION
1
Perform user registration at
http://www.toyota.com/entune/.
SETUP REQUIRED TO USE
Entune App Suite
Perform the following actions.
1
User registration
2
Download the Entune App Suite application to your cellular phone.
3
Register the cellular phone to the system.
4
Download Entune App Suite applications to the system.
In order to use Entune App Suite, the following actions must first be performed:
 User registration with a service contract
(P.259)
 Download the Entune App Suite application onto your cellular phone, and login to
the application. (P.260)
 Register the cellular phone that the
Entune App Suite application was downloaded to with the system. (P.260)
9
Entune App Suite
 Register a Bluetooth® phone with the
hands-free system. (P.40)
 Download Entune App Suite applications
to the system. (P.260)
259
1. Entune App Suite OVERVIEW
REGISTERING THE Entune App
Suite APPLICATION
1
Download the Entune App Suite application to your cellular phone.
2
Run the Entune App Suite application
on your cellular phone.
3
Enter the information required into the
Entune App Suite application. Login to
the application.
INFORMATION
● Applications can only be used when the
Entune App Suite application has been
downloaded to your cellular phone and
the application is running.
● Entune App Suite operational procedures can also be confirmed by visiting
http://www.toyota.com/entune/.
● In order to use applications, it is necessary to run the Entune App Suite application on your cellular phone.
● If an iPhone is connected via Bluetooth®
and USB at the same time, system operation may become unstable. For known
phone compatibility information, refer to
http://www.toyota.com/entune/.
● If an Entune App Suite application is
used while iPod audio is being played
back, system operation may become
unstable.
260
DOWNLOADING Entune App
Suite APPLICATIONS
1
The actions on P.259 need to be performed before Entune App Suite applications can be downloaded.
2
Once your phone is running the Entune
App Suite application with a valid account logged in and is connected to the
system, an on-screen pop-up will be
displayed offering to begin downloading Entune App Suite applications to
the system. After download has started, see P.263 for more information.
2. Entune App Suite OPERATION
1. Entune App Suite
USING Entune App Suite
2
Select the desired application button.
Entune App Suite is a service that enables the usable contents of a cellular
phone to be displayed on and operated
from the screen. Before Entune App
Suite can be used, a few actions need
to be performed first. (P.259)
For details about the function and service of each application, refer to http://
www.toyota.com/entune/.
1
Press the “APPS” button.
No.
Function
Page
Select to activate an application.

Select to update the application.
262
Select to reorder the applications.
263
9
Entune App Suite
261
2. Entune App Suite OPERATION
UPDATING an application
3
Check that downloading is completed.
When Entune App Suite is activated,
an application may need to be updated. By updating, an application can be
kept to the latest version. When updating the application, it is necessary to
download the updated data and install
it.
■DOWNLOADING THE UPDATED
DATA
If an update is available, “Update” can
be selected.
1
Select “Update”.
No.
Function
Select to install the update later. The
screen will return to the last displayed screen. Installing the updated data later: P.263
Select to display detailed information about the updated data.
Select to install the updated data.
Follow the steps “INSTALLING THE
UPDATED DATA” from “STEP 2”.
(P.263)
INFORMATION
2
Check that downloading is started.
“Download in Background”: Select to
operate other function while downloading.
“Cancel”: Select to cancel updating.
262
● Application download time may vary
based on the speed of the cellular network.
● Application download can be resumed
after turning off and back on.
● Future mandatory updates will display
an on-screen pop-up when available.
● Entune App Suite function cannot be
operated while mandatory updates
downloading.
2. Entune App Suite OPERATION
■INSTALLING THE UPDATED DATA
After the downloading is complete,
“Update” will be changed to “Install”.
1
2
Select “Install”.
Select “Continue”.
“Later”: Select to postpone the installation
of the updated data and go back to the previous screen.
3
Check that installing is started.
“Install in Background”: Select to operate other function while installing.
4
REORDERING THE
APPLICATIONS
Order of the applications can be
changed.
1
2
Display the “Apps” screen. (P.261)
3
Select the desired application to be
moved.
4
Select
or
to move the application, and select “OK”.
Select “Reorder”.
Select “OK” after the installing is complete.
9
INFORMATION
Entune App Suite
● Entune App Suite function cannot be
operated while installing.
263
2. Entune App Suite OPERATION
IF A MESSAGE APPEARS ON THE SCREEN
When problems occur starting up the application player, a message will appear on
the screen. Referring to the table below to identify the problem, take the suggested
corrective action.
Message
Display conditions
Corrective action
“This feature is unavailable
during an emergency call.”
Safety Connect is being implemented.
After Safety Connect is finished, perform the operation
again.
“This feature is unavailable
while transferring contacts.”
Contacts are being transferred manually from the
phonebook.
When the transfer of contacts
is complete, perform the operation.
“Unable to connect to a
Bluetooth* phone. For troubleshooting
assistance,
please visit toyota.com.”
The cellular phone cannot be
connected.
Refer
to
http://
www.toyota.com/entune/ to
confirm if the phone is compatible or not.
“This feature is unavailable
during a handsfree call.”
A hands-free
progress.
After the hands-free call is finished, perform the operation.
call
is
in
“To use these services, an
active application needs to be
running on your phone. For
more information, please visit
toyota.com.”
The Entune App Suite application cannot be connected
to Bluetooth® SPP.
“Entune connection has been
lost. Please confirm your connection.”
Communication was disconnected.
Refer
to
http://
www.toyota.com/entune/ to
confirm if the phone is
Bluetooth® SPP compatible
or not, and then activate the
Entune App Suite application.
After a few moments, retry
the operation.
*: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
264
2. Entune App Suite OPERATION
SETTING A DESTINATION
USING Entune App Suite
LINKING Entune App Suite
AND NAVIGATION FUNCTION
The system can set a destination and
make a hands-free call via Entune App
Suite. For details about the function
and service of each application, refer
to http://www.toyota.com/entune/.
1
2
3
4
5
Press the “APPS” button.
Locations that were searched using
Entune App Suite can be set as a destination.
1
Display the “Web Search” screen.
(P.265)
2
Select the desired application button to
search.
3
4
5
Enter a search term, and select “GO”.
6
Select “OK” to start guidance.
Select “Map”.
Select “Go to
”.
Select “Navigation”.
Select “Dest.”.
Select “Web Search”.
9
Entune App Suite
Check that the “Web Search” screen is
displayed.
 For the operation of the route guidance
screen and the function of each screen
button: P.216
265
2. Entune App Suite OPERATION
MAKING A PHONE CALL
USING Entune App Suite
Phone calls can be made to locations
which were searched using Entune
App Suite.
1
Display the “Web Search” screen.
(P.265)
2
Select the desired application button to
search.
3
4
5
Enter a search term, and select “GO”.
Information can be entered to an application by the software keyboard or
voice recognition. For details about the
function and service of each application, refer to http://www.toyota.com/entune/.
 The keyboard layout can be changed.
(P.52)
Select “Call”.
USING THE SOFTWARE
KEYBOARD
Select “Yes”.
“Cancel”: Select to cancel making a
phone call.
6
Entune App Suite KEYWORD
OPERATION
Check that the “Call” screen is displayed.
 For phone operation and the function of
each screen button: P.160
1
2
Display the “Apps” screen. (P.261)
3
4
Select the character input space.
5
Entering characters will be reflected on
the character input space.
Select the desired application button.
Enter a search term, and then select
“OK”.
 For details on operating the keyboard:
P.35
266
2. Entune App Suite OPERATION
ENTERING A KEYWORD USING
THE VOICE RECOGNITION
FUNCTION
1
2
Display the “Apps” screen. (P.261)
3
4
Press the talk switch. (P.126)
Select the desired application button.
Say the desired keyword.
 Completion of saying the keyword will be
detected automatically.
5
Search results will be displayed on the
screen.
9
Entune App Suite
267
3. SETUP
1. Entune App Suite SETTINGS
Settings are available for Entune App
Suite.
1
SCREEN FOR Entune App
Suite SETTINGS
Press the “APPS” button.
No.
2
3
4
5
268
Select “Setup”.
Select “Entune”.
Function
Select to set the voice guidance volume.
Select to set the pop up reminder for
cellular phone data usage. (P.269)
Select the items to be set.
Select “OK”.
Select to reset all setup items.
3. SETUP
PHONE DATA PLAN POP-UP
SETTINGS
The phone data plan pop-up can be set
when a paid application is downloaded.
1
Display the “Entune Settings” screen.
(P.268)
2
3
Select “Phone Data Plan Pop-Up”.
4
Select “OK”.
Check the desired function to be operated.
9
Entune App Suite
269
3. SETUP
270
1
INDEX
2
3
4
5
6
7
8
9
271
ALPHABETICAL INDEX
A
D
AAC.......................................................... 90
AM............................................................ 72
APPS button ............................................ 10
“Apps” screen........................................... 12
AUDIO button........................................... 10
Audio settings ........................................ 114
AUX ........................................................ 109
Data services settings ............................ 138
B
Setting download methods ................. 138
Destination search screen...................... 204
Driver settings .......................................... 60
E
Editing route ........................................... 226
Adding destinations ............................ 227
Deleting destinations .......................... 227
Bluetooth®................................................ 40
Detour setting ..................................... 229
Profiles ................................................. 42
Reordering destinations...................... 227
Registering a Bluetooth® audio
player ................................................ 41
Selecting route type............................ 228
Registering a Bluetooth® phone........... 40
Bluetooth® audio.................................... 104
Connecting a Bluetooth® device ........ 108
Listening to Bluetooth® audio............. 108
Bluetooth® phone................................... 150
Bluetooth® phone message function ..... 163
Setting route preferences ................... 228
Starting from adjacent road .................230
Emergency ............................................. 213
Entering letters and numbers/
list screen operation ............................. 35
Entering letters and numbers ............... 35
Entune App Suite ................................... 261
Entering keyword operation................ 266
C
Calling on the Bluetooth® phone............ 154
Casual speech recognization................. 132
CD............................................................ 90
Playing an audio CD............................. 93
Playing an MP3/WMA/AAC disc........... 93
Command list ......................................... 133
272
Linking Entune App Suite and
navigation function .......................... 265
F
M
FM radio................................................... 72
Maintenance ............................................ 61
Map database version and
covered area ...................................... 252
Map screen information ......................... 197
G
General settings....................................... 52
GPS (Global Positioning System).......... 250
Limitations of the navigation
system ............................................ 250
H
HOME button ........................................... 10
“Home” screen ......................................... 14
Home screen operation ........................... 34
I
Initial screen............................................. 30
Internet radio............................................ 89
iPod.......................................................... 99
K
Keyboard ................................................. 35
Displaying information about
the icon where the cursor is set ...... 199
Standard map icons ........................... 200
Map screen operation ............................ 191
Adjusting location in small
increments ...................................... 196
Current position display...................... 191
Map scale ........................................... 191
Orientation of the map........................ 192
Screen scroll operation....................... 195
Switching the map mode .................... 193
Memory points settings .......................... 231
Deleting previous destinations ........... 239
Setting up address book..................... 235
Setting up areas to avoid.................... 237
Setting up home ................................. 232
Setting up preset destinations ............ 233
Microphone ............................................ 126
MP3.......................................................... 90
273
ALPHABETICAL INDEX
N
R
Navigation .............................................. 187
Rear view monitor system...................... 140
Receiving weather information............... 136
Receiving on the Bluetooth® phone ....... 159
O
Operating information ............................ 116
CD player and disc ............................. 117
Error messages .................................. 124
File information................................... 120
iPod .................................................... 119
Radio .................................................. 116
Terms ................................................. 123
Overview buttons ..................................... 10
P
Phonebook............................................. 156
Phone/message settings........................ 168
Incoming calls..................................... 159
Registering home ..................................... 20
Registering preset destinations................ 22
Registering/connecting Bluetooth®
device ................................................... 40
Certification........................................... 43
Profiles.................................................. 42
Registering a Bluetooth® audio player
for the first time ................................. 41
Registering a Bluetooth® phone
for the first time ................................. 40
Route guidance screen .......................... 220
During freeway driving........................ 222
“Contact/Call History Settings”
screen ............................................. 170
Route overview................................... 221
“Messaging Settings” screen.............. 178
Turn list screen ................................... 224
“Phone Display Settings” screen ........ 179
Turn-by-turn arrow screen .................. 224
Phone/message settings screen ........ 168
When approaching intersection .......... 223
Route trace............................................. 199
“Sound Settings” screen..................... 169
PWR·VOL knob ....................................... 10
274
Screen for route guidance .................. 220
S
T
Satellite Radio.......................................... 82
Screen adjustment................................... 38
Search operation ................................... 206
Talking on the Bluetooth® phone ........... 160
Searching by coordinates................... 215
Incoming call waiting .......................... 162
Touch screen gestures ............................ 32
Touch screen operation ........................... 33
Traffic information .................................. 201
Traffic settings........................................ 244
Searching by emergency ................... 213
Auto avoid traffic................................. 245
Searching by intersection and
freeway ........................................... 213
My traffic routes.................................. 246
Searching by address ........................ 208
Searching by address book................ 212
Searching by map .............................. 215
Searching by point of interest............. 209
Searching from previous
destinations .................................... 212
Screen for traffic settings.................... 244
Troubleshooting ..................................... 180
TUNESCROLL button............................. 10
Typical voice guidance prompts............. 225
Selecting search area ........................ 207
U
Setting home as destination............... 207
USB/AUX port .......................................... 69
USB memory............................................ 94
Setting preset destinations
as destination ................................. 207
Setting Bluetooth® details........................ 44
“Bluetooth* Setup” screen .................... 44
Connecting a Bluetooth® device .......... 47
Deleting a Bluetooth® device ............... 46
Editing the Bluetooth® device
information........................................ 49
Playing a USB audio ............................ 98
V
Vehicle settings........................................ 59
Voice command system......................... 126
Voice settings........................................... 58
Registering a Bluetooth® device .......... 45
“System Settings” screen ..................... 50
Setting home as the destination .............. 25
“Setup” screen ......................................... 18
Starting route guidance.......................... 216
Steering switches................................... 112
*: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
275
ALPHABETICAL INDEX
W
WMA ........................................................ 90
X
XM Satellite Radio ................................... 82
Displaying the radio ID ......................... 87
How to subscribe to
an XM Satellite Radio ....................... 85
If the satellite radio tuner
malfunctions...................................... 88
Presetting a channel............................. 87
Selecting a channel from the list .......... 87
276
Map database information and updates
277
278
279
280
281
282
B. VISA. With respect to any VISA data, VISA specifically requires the following:
i.) All materials are the copyrighted property of AISIN and/or TELECOMMUNICATION SYSTEMS, INC. and its licensors. No material from this site may be copied, reproduced, republished,
uploaded, posted, transmitted, stored, or distributed in any way, except that end user may download one listing (a location’s name and address) on an individual non-automated basis per visiting
session to the Licensee site or application, into end user’s personal electronic address book. A
personal electronic address book may not be shared by end user with other end users, nor may
it be copied, reproduced, republished, uploaded, posted, transmitted, stored or distributed in any
way. Use of the personal electronic address book must be for end user’s personal, noncommercial use only.
ii.) End user may not use any material from AISIN’s site or application for the purpose of compiling, enhancing, verifying, supplementing, or otherwise modifying VISA databases, lists, or directories of any kind, including, but not limited to, location databases, mailing lists, contact lists,
marketing lists, geographic directories, or any other compilation or collation of information which
is sold, rented, published, distributed, or in any manner supplied to a third party.
Certain business data provided by Infogroup © 2012, All Rights Reserved.
283
1. Certification
 Gracenote, the Gracenote logo and logotype, “Powered by Gracenote”, MusicID, Playlist
Plus and MediaVOCS are either registered trademarks or trademarks of Gracenote, Inc.
in the United States and/or other countries
284
285
For U.S. owners
286
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement