Toyota 2016 Sequoia Quick Reference Guide

Toyota 2016 Sequoia Quick Reference Guide
SEQUOIA
2 0 1 6
CUSTOMER EXPERIENCE CENTER
1-800-331-4331
QUICK REFERENCE GUIDE
Printed in U.S.A. 7/15
15-TCS-08583
00505QRG16SEQ
2016
Sequoia
NOTES
This Quick Reference Guide is a summary of basic vehicle
operations. It contains brief descriptions of fundamental operations
so you can locate and use the vehicle’s main equipment quickly
and easily.
The Quick Reference Guide is not intended as a substitute for the
Owner’s Manual located in your vehicle’s glove box. We strongly
encourage you to review the Owner’s Manual and supplementary
manuals so you will have a better understanding of your vehicle’s
capabilities and limitations.
Your dealership and the entire staff of Toyota Motor Sales, U.S.A.,
Inc. wish you many years of satisfied driving in your new Sequoia.
A word about safe vehicle operations
This Quick Reference Guide is not a full description of Sequoia
operations. Every Sequoia owner should review the Owner’s
Manual that accompanies this vehicle.
Pay special attention to the boxed information highlighted in
color throughout the Owner’s Manual. Each box contains safe
operating instructions to help you avoid injury or equipment
malfunction.
All information in this Quick Reference Guide is current at the
time of printing. Toyota reserves the right to make changes at
any time without notice.
49
INDEX
OVERVIEW
FEATURES/OPERATIONS Accessory meter
EMERGENCY FEATURES
1
2
3
Doors-Child safety locks
Floor mat installation
Seat belts
Seat belts-Shoulder belt anchor
Spare tire & tools
Star Safety SystemTM
Tire Pressure Monitoring (warning) System
19
18
18
33
35
32
33
33
34-35
32
Visit your Toyota dealer for information on customizing this feature.
Programmable by customer. Refer to the Owner’s Manual for instructions and more information.
HomeLink® is a registered trademark of Gentex Corporation.
1
SAFETY AND EMERGENCY FEATURES
SAFETY AND
29
22-23
24-25
11
11
37-46
13
26
31
28
19
20
27
12
26
17
20
28
12
30
30
31
25
15
14
23
15
16
13
29
21
11
21
FEATURES/OPERATIONS
Air Conditioning/Heating
Audio
Auto lock/unlock1
Automatic Transmission
Bluetooth® Device Pairing Section
Blind Spot Monitor (BSM)
Cruise control
Cup holders
Door locks
Door-Power back
Driving position memory
Dynamic Laser Cruise Control
Four-wheel drive
Garage door opener (HomeLink®)3
Lights1 & turn signals
Moonroof
Multi-Information Display2
Parking brake
Power outlets-12V DC
Power outlets-120V AC
Rear seat entertainment system
Rear view monitor system
Seat adjustments-Front
Seat adjustments-Rear
Seat ventilators/heaters
Seats-Folding second row seats
Seats-Folding third row seats
Seats-Head restraints
Telephone controls (Bluetooth®)
Tilt and telescopic steering wheel
TOW/HAUL switch
VSC OFF switch
Window-Back
Windows
Windshield wipers & washers
10
9
10
6-7
5
2-4
8
9
OVERVIEW
Engine maintenance
Fuel tank door release and cap
Hood release
Indicator symbols
Instrument cluster
Instrument panel
Keyless entry1
Light control-Instrument panel
OVERVIEW
Instrument panel
Steering wheel controls (if equipped)
Steering wheel audio controls1,2
Voice command button1,2
Telephone controls1,2
Cruise control
Dynamic Laser Cruise Control distance switch1
Headlight, turn signal and front fog light1 controls
Gauges and meters
Wiper and washer controls
Tire Pressure Monitoring (warning) System reset
Power back window switch
VSC OFF switch
Ignition switch
Personal/Interior light main switch
Instrument panel light control
Tilt and telescopic steering control switch1
2
OVERVIEW
Details on the center panel
area on next page
FEATURES/OPERATIONS
1
If equipped
For details, refer to the “Navigation System Owner’s Manual” and “2016
Entune™ Audio Quick Reference Guide.”
2
3
SAFETY AND EMERGENCY FEATURES
Tilt and telescopic steering lock release lever1
Roll Sensing of Curtain Shield Airbag OFF switch1
REVERSE TILT (side mirrors) switch1
Headlight cleaner1
Power back door button1
Blind Spot Monitor (BSM) switch1
Power rearview mirror controls
OVERVIEW
Center panel area
Accessory meter
Theft deterrent/Engine immobilizer system indicator
Multimedia system2
Air Conditioning controls
Outside rearview mirror defogger1/Back window defogger/Windshield
wiper de-icer button1
12V DC power outlet
Seat heater1 and ventilator1 controls
Cigarette lighter
AUX audio jack/USB port
Height control switch1
AVS switch1
TOW/HAUL button1
Center differential lock/unlock switch1
Front-wheel drive control switch1
Intuitive parking assist button1
Multi-Information Display control buttons1 and/or accessory meter
control buttons1
Emergency flasher button
1
If equipped
For details, refer to the “Navigation System Owner’s Manual” and
“2016 Entune™ Audio Quick Reference Guide.”
2
4
Instrument cluster
With Multi-Information Display
OVERVIEW
Without Multi-Information Display
FEATURES/OPERATIONS
* If equipped
5
SAFETY AND EMERGENCY FEATURES
Tachometer
Speedometer
Service indicator and reminder
Fuel gauge
Voltmeter
Engine oil pressure gauge
Engine coolant temperature
Odometer/Trip meter and trip meter reset button
Multi-Information Display
Odometer and two trip meters
Automatic Transmission shift position indicator
Automatic Transmission shift range display
Automatic Transmission fluid temperature gauge*
OVERVIEW
Indicator symbols
For details, refer to “Indicators and warning lights,” Section 2-2, 2016 Owner’s
Manual.
Brake system warning*
Driver seat belt reminder
(alarm will sound if speed is over 12 mph)
Front passenger seat belt reminder
(alarm will sound if speed is over 12 mph)
Charging system warning*
AIR BAG ON indicator
AIR BAG OFF indicator*
Malfunction/Check Engine indicator*
Maintenance/Service required indicator
Low fuel level warning
Open door warning
Airbag SRS warning*
Low windshield washer fluid level warning
Master warning
Low Tire Pressure Warning*
Theft deterrent/Engine immobilizer system indicator
Power steering warning*
Roll Sensing of Curtain shield Airbag OFF indicator*
Headlight low/high beam indicator
Turn signal indicator
Shift position and shift range indicators
Vehicle Stability Control OFF indicator*
TOW/HAUL mode indicator
6
AUTO Limited Slip Differential indicator*
High/Low speed four-wheel drive indicator
OVERVIEW
Slip indicator*
Height control indicator*
Height control/MANUAL indicator*
Center differential lock indicator
Cruise control indicator
Anti-lock Brake System warning*
Automatic Transmission fluid temperature warning*
Traction Control OFF indicator*
Fuel tank door position
FEATURES/OPERATIONS
Blind Spot Monitor (BSM) outside rearview mirror indicators
SAFETY AND EMERGENCY FEATURES
* If indicator does not turn off within a few seconds of starting engine, there may be a
malfunction. Have vehicle inspected by your Toyota dealer.
7
OVERVIEW
Keyless entry
Locking operation
With power back door
Without power back door
Push
Unlocking operation
With power back door
Without power back door
Push ONCE: Driver door
TWICE: All doors
NOTE: If a door is not opened within 60 seconds of unlocking, all doors will relock for
safety.
Power back door operation (if equipped)
Push and hold
Panic button
Push and hold
8
Fuel tank door release and cap
OVERVIEW
Turn to open
Pull
NOTE: Tighten until one click is
heard. If the cap is not tightened
enough, Check Engine “ ”
indicator may illuminate.
FEATURES/OPERATIONS
Store
Light control-Instrument panel
Brightness
control
+
9
SAFETY AND EMERGENCY FEATURES
-
OVERVIEW
Hood release
Pull
Pull up latch and raise hood
Engine maintenance
Windshield washer fluid tank
Engine oil level dipstick
Engine coolant reservoir
Engine oil filler cap
NOTE: Regularly scheduled maintenance, including oil changes, will help
extend the life of your vehicle and maintain performance. Please refer
to the “Warranty & Maintenance Guide.”
10
FEATURES/OPERATIONS
Automatic Transmission
Reverse
Neutral
OVERVIEW
Park*
Drive
“S” mode
“S” “D”
* The ignition switch must be “ON” and the brake pedal depressed to shift from Park.
“S” (Sequential) mode
Shift the shift lever to “S” position from “D” position.
+: Upshift (push and release)
-: Downshift (pull and release)
TOW/HAUL switch (if equipped)
FEATURES/OPERATIONS
Downshifting increases power going uphill, or provides engine braking downhill.
For best fuel economy during normal driving conditions, always drive with the
shift lever in the “D” position.
System ON/OFF
“TOW/HAUL” mode can be used when carrying heavy loads. As fuel economy is
reduced while in “TOW/HAUL” mode, deactivating when driving without a load is
recommended.
Refer to the Owner‘s Manual for more details on this system before attempting
to use it.
Refer to the Owner’s Manual for more details.
11
SAFETY AND EMERGENCY FEATURES
Auto lock/unlock
Automatic door locks can be programmed to operate in four different modes, or
turned OFF.
-Doors lock when shifting from Park.
-Doors lock when the vehicle speed is approximately 12 mph or higher.
-Doors unlock when shifting into Park.
-Doors unlock when the driver’s door is opened within 10 seconds after turning the
ignition switch to the “ACC” or “LOCK” position.
FEATURES/OPERATIONS
Four-wheel drive (if equipped)
Four-wheel drive control switch
Turn
Turn
Push
and turn
WD High speed (2WD)
Turn to “2WD” from “4H” with speed below 62 mph.
High speed (4WD)
Turn to “4H” from “2WD” with speed below 62 mph.
Shift to “N” position when stopped, then turn to “4H” from “4L.”
Low speed (4WD)
Shift to “N” position when stopped, then push and turn to “4L” from “4H.”
For best fuel economy and performance under normal driving conditions, keep in
“2WD” position.
Center differential lock/unlock switch
Push
Lock the center differential if the vehicle’s wheels get stuck in a ditch or when
driving on a slippery or bumpy surface.
Refer to the Owner‘s Manual for more details on this system before attempting
to use it.
Parking brake
Set: Depress
Release: Depress again
12
Blind Spot Monitor (BSM)(if equipped)
OVERVIEW
System ON/OFF
Refer to the Owner‘s Manual for more details on this system before attempting
to use it.
Seats-Head restraints
Front
FEATURES/OPERATIONS
The Blind Spot Monitor is a system that assists the driver to confirm safety when
changing lanes. The system uses radar sensors to detect vehicles that are traveling
in an adjacent lane in the area that is not reflected in the outside rearview mirror
(the blind spot), and advises the driver of the vehicles’ existence via the outside
rearview mirror indicator.
Second row
Lock release button
Middle head restraint in
8-passenger models only.
Lock release button
Lock release button
13
SAFETY AND EMERGENCY FEATURES
Third row (outside)
Third row (center)
FEATURES/OPERATIONS
Seat adjustments-Rear
Second row
Separate seat
Bench seat
Third row
Manual seat
Power seat
Seat position (forward/backward)
Seatback angle
Seatback angle/lock release and slide
Seatback folding/returning
Refer to the Owner’s Manual for more details.
14
Seat adjustments-Front
Manual seat
Power seat
OVERVIEW
Seat position (forward/backward)
Seatback angle
Seat height
Seat cushion angle
Lumbar support
Position, cushion angle and height
Leg support (if equipped)
(1)
(3)
FEATURES/OPERATIONS
Seats-Folding second row seats
(2)
Separated seat
Bench seat
Pull
Pull
(1)
(2)
(3)
(4)
Lower the head restraints.
Stow the seat belt buckles.
Fold down the seatback.
Fold out the board (if equipped) from the seatback.
15
SAFETY AND EMERGENCY FEATURES
(4)
FEATURES/OPERATIONS
Seats-Folding third row seats
(1)
(2)
Insert
Insert
(4)
(3)
(5) Manual seat only
(6) From rear door side
Manual seat
From back door side
Manual seat
Pull
Power seat
(1)
(2)
(3)
(4)
(5)
(6)
Power seat
Release the center seat belt tab.
Stow the center seat belt tab.
Lower the head restraint.
Stow the seat belt buckles.
Fold the head restraint.
Fold the seats.
16
Lights & turn signals
Headlights
Type B
Auto
Auto
Headlights
Parking lights
Headlights
Parking lights
OVERVIEW
Type A
Type D
Type C
Headlights
Parking lights
Auto
DRL OFF
Headlights
Parking lights
Auto
DRL OFF
High beam
FEATURES/OPERATIONS
High beam flasher
Low beam
-Daytime Running Light system (DRL) Automatically turns on the front turn
signal lights upon starting engine and releasing parking brake.
-Automatic light cut off system Automatically turns lights off after a delay of
30 seconds, or the lock switch on remote may be pushed after locking.
Front fog lights (if equipped)
Turn signals
Type A
Right turn
Type B
Lane change
Left turn
Turn
Front fog lights come on only when the
headlights are on low beam.
17
SAFETY AND EMERGENCY FEATURES
Lane change
Turn
FEATURES/OPERATIONS
Windshield wipers & washers
Front
Type A
Type B
Single wipe
Adjust frequency*
Single wipe
Adjust frequency*
Interval wipe
Interval wipe
Slow
Slow
Fast
Fast
Pull to wash and wipe
* Intermittent windshield wiper frequency adjustment
Rotate to increase/decrease wipe frequency.
Rear
Type A
Wash and wipe
Wipe
Interval wipe
Type B
Wash and wipe
Wipe
Interval wipe
Wash and wipe
Wash and wipe
Windows
Driver side
Window lock
switch
Up
Down
Automatic operation Push the switch completely down or pull it completely
up and release to fully open or close. To stop window partway, lightly push the
switch in the opposite direction.
Window lock switch Deactivates all passenger windows and back window. Driver’s
window remains operable.
18
Window-Back
Operating from inside
OVERVIEW
Open
Close
Automatic operation Push the switch completely in or pull it completely out and
release to fully open or close. To stop window midway, lightly push the switch in
the opposite direction.
Operating from outside
Open Close
FEATURES/OPERATIONS
Door-Power back (if equipped)
Instrument panel
Back door (close only)
Push and hold
Open: Push and hold
Close: Push and hold again
NOTE: Door will stop closing if
obstructed, or to manually stop
door closing, push button again.
NOTE: If battery is disconnected, the power back door needs to be reinitialized.
Refer to the Owner’s Manual for more details.
19
SAFETY AND EMERGENCY FEATURES
Push and hold
FEATURES/OPERATIONS
Moonroof (if equipped)
Sliding operation
Tilting operation
Tilt
Open
Close
Close
Push to open/close. To stop partway, press the switch lightly.
Driving position memory
(driver’s seat) (if equipped)
Manual
To save
To recall
Push
Push
(1) Adjust driver’s seat, steering wheel, and
outside rear view mirrors.
(2) Push “SET” and “1” or “2” buttons to
save.
(1) Press “1” or “2” to recall.
You can save up to two driving positions to memory and recall it with the touch
of a button. Make sure shift lever is in “P” position and ignition switch is in the
“ON” position.
Refer to the Owner‘s Manual for more details on this system.
20
Tilt and telescopic steering wheel
Manual
Length
Lock release lever
OVERVIEW
Angle
Hold wheel, push lever down, set angle and length and return lever.
Power
Up
FEATURES/OPERATIONS
Away from
the driver
Toward the
driver
Down
Control switch
Toggle the control switch to set angle and length.
NOTE: Do not attempt to adjust while the vehicle is in motion.
VSC OFF switch
The VSC OFF switch is used to switch between modes related to the TRAC, VSC
and Auto LSD functions.
Refer to Section 2-4 of the Owner’s Manual for more information.
21
SAFETY AND EMERGENCY FEATURES
VSC OFF switch
FEATURES/OPERATIONS
Air Conditioning/Heating
Front Air Conditioning
Control panel
Display
Fan speed
Automatic climate control ON
Adjusting the temperature setting will cause the airflow vents, air intake and
fan to adjust automatically.
Air Conditioning ON/OFF
Temperature selector (driver side)
Windshield defogger (outside air only)
Airflow vent
In “
” mode, use outside air (“
” indicator “OFF”) to reduce window
fogging.
Temperature selector (front passenger side)
“SYNC” button
Indicator ON: Synchronized temperature settings for driver, front passenger
and rear seats.
Indicator OFF: Separate temperature settings for driver, front passenger and
rear seats.
Outside rearview mirror/Back window defogger or windshield wiper de-icer
(if equipped)
Rear Air Conditioning ON/OFF
Temperature selector (rear passenger area*)
Recirculate cabin air (outside air when OFF)
Climate control OFF
* To change the rear seat setting, press the “REAR” button.
22
Rear Air Conditioning
OVERVIEW
Automatic climate control ON
Display
Airflow vent
Fan speed
Temperature selector
Climate control OFF
Seat ventilators/heaters (if equipped)
With ventilators
Driver’s seat
Heater only
Driver’s seat
Front passenger’s seat
Ventilator
Ventilator
Heater
Heater
Front passenger’s seat
Turn
Turn
ON
ON
FEATURES/OPERATIONS
Front seats
Second seats
Push
Low heat
setting
Push
Push lightly in the opposite direction to turn off.
23
SAFETY AND EMERGENCY FEATURES
High heat
setting
FEATURES/OPERATIONS
Audio
Entune™ Audio Plus with Connected Navigation App Suite1 Touch screen display
Eject CD
Turn to tune
radio stations
manually or
select tracks
or files
Push to turn
ON/OFF
Push to
display audio
screen
Seek station/
CD track
select
Entune™ Premium (JBL®) Audio with Integrated Navigation and App Suite1
2
1
Refer to the “Navigation System Owner’s Manual” and “2016 Entune™ Audio Quick
Reference Guide.”
2 Entune™ Premium JBL® Audio
USB/AUX port
USB port
By connecting a USB-compatible portable audio device or USB memory to the
USB port, you can listen to music from the portable audio device or USB memory
through the vehicle’s speaker system.
AUX port
By inserting a mini plug into the AUX port, you can listen to music from a portable
audio device through the vehicle’s speaker system while in AUX mode.
24
Steering wheel switches (if equipped)
OVERVIEW
Volume control
>
>
>
>
“
”“
”
Use to search within the selected audio medium (radio, CD, etc.).
“MODE”
Push to turn audio ON and select an audio mode. Push and hold to mute or
pause the current operation.
FEATURES/OPERATIONS
Rear view monitor system
The rear view monitor system displays an image of the view from the bumper
of the rear area of the vehicle. The camera for the rear view monitor system is
located above the license plate.
Refer to the Owner‘s Manual for more details on this system.
25
SAFETY AND EMERGENCY FEATURES
To adjust the image on the rear view monitor screen, press the “SETUP” button
and select “Display” on the “Setup” screen. Select “Camera” to adjust the
screen contrast and brightness.
FEATURES/OPERATIONS
Garage door opener (HomeLink®)*
(if equipped)
Garage door openers manufactured under license from HomeLink® * can be
programmed to operate garage doors, estate gates, security lighting, etc.
Refer to “Garage door opener,” Section 3-5 in the Owner’s Manual for more
details.
For programming assistance, contact HomeLink® at 1-800-355-3515, or visit
http://www.homelink.com.
* HomeLink® is a registered trademark of Johnson Controls, Inc.
Cruise control
Turning system ON/OFF
System ON/OFF
Functions
Resume2
Increase speed
Cancel1
Set
1
2
Decrease speed
The set speed may also be cancelled by depressing the brake pedal.
The set speed may be resumed once vehicle speed exceeds 25 mph.
26
Dynamic Laser Cruise Control (if equipped)
Fixed speed mode
OVERVIEW
Refer to the Owner’s Manual for more details and complete safety precautions
before attempting to use “Dynamic Laser Cruise Control.”
(1) To select conventional/fixed speed control Push the ON-OFF button. Push the
lever forward and hold.
(2) To set, cancel and resume a speed Refer to instructions for Cruise Control in
this guide.
Distance control mode
FEATURES/OPERATIONS
Distance control mode will cruise at a set speed, decelerate to maintain selected
distance from a slower vehicle traveling in front of you, and accelerate back up
to the selected speed if the vehicle traveling in front of you changes lanes or
speeds up.
(1) To select distance control mode Push the ON-OFF button. The “CRUISE”
indicator will come on.
(2) To set, cancel and resume a speed Refer to instructions for Cruise Control in
this guide.
NOTE: Once vehicle speed is set, pushing lever up toward “+ RES” will increase
speed to the nearest 5 mph, and then in 5 mph increments. Pushing lever down
toward “- SET” will reduce speed in the same way.
MIDDLE
SHORT
(3) To change the vehicle-to-vehicle distance
Push the distance button to cycle through the settings, which will change
progressively from LONG to MIDDLE to SHORT.
27
SAFETY AND EMERGENCY FEATURES
LONG
FEATURES/OPERATIONS
Multi-Information Display (if equipped)
Push “INFO” to change information in the following:
(1) Zoom display of odometer and trip meter
(2) Average gas mileage
(3) Current gas mileage
(4) Miles left on remaining fuel
(5) Running time from engine start
(6) Average vehicle speed
Push “SETUP” to customize to the following settings:
(1) UNIT
(2) KEYLESS ENTRY FEEDBACK
(3) KEYLESS ENTRY RELOCK TIMER
(4) KEYLESS ENTRY ALL DOORS UNLOCK
(5) DOOR AUTO LOCKING
(6) DOOR AUTO UNLOCKING
(7) HEADLAMPS AUTO OFF TIMER
(8) COURTESY LAMPS OFF TIMER
(9) LANGUAGE
(10) DEFAULT SETTING
Door locks
Unlock
Lock
28
Accessory meter
OVERVIEW
*if equipped
Telephone controls (Bluetooth®)
(if equipped)
Audio unit
Microphone
FEATURES/OPERATIONS
Change information(MultiOutside temperature/Cruise
information)*
information display (if equipped)
“SELECT RESET” button*
Clock
“SETUP” button to customize unit*
Hour set
Minute set
Refer to your Owner’s Manual for complete details on this system before
attempting to use it.
Steering wheel telephone switches
Start call
End call
Voice command
button
Bluetooth® technology allows dialing or receipt of calls without taking hands from
the steering wheel or using a cable to connect the compatible telephone and the
system.
Refer to “Using a Bluetooth® phone” Section 3-2 in the Owner’s Manual, for more
details.
29
SAFETY AND EMERGENCY FEATURES
Volume
FEATURES/OPERATIONS
Power outlets-12V DC (if equipped)
Instrument panel
Inside of the center console box
Back of the center console box
Luggage compartment
Key must be in the “ACC” or “ON” position to be used.
Power outlets-120V AC (if equipped)
Key must be in the “ON” position to be used.
30
Rear seat entertainment system
(if equipped)
OVERVIEW
FEATURES/OPERATIONS
Front audio system
DVD player
DVD screen
Remote control
A/V input port
120V AC power outlet
Headphone volume controls and headphone jacks
For details, refer to the “Navigation System Owner’s Manual.”
Cup holders
Front
Front console
Back of the front console
Rear side trim
Rear console box (if equipped)
31
SAFETY AND EMERGENCY FEATURES
Rear
SAFETY AND EMERGENCY FEATURES
Tire Pressure Monitoring (warning)
System
System reset initialization
SET” button
1. Push and hold “
until the indicator blinks three
times.
2. Wait a few minutes to allow
initialization to complete.
After adjusting tire pressures, or after tires have been rotated or replaced, turn
the ignition switch to “ON” and press and hold the “ SET” button until indicator
blinks three times. Let the vehicle sit for a few minutes to allow initialization to
complete.
Refer to the load label on the door jamb or the Owner’s Manual for tire inflation
specifications.
If the tire pressure indicator flashes for more than 60 seconds and then remains on,
take the vehicle to your local Toyota dealer.
NOTE: The warning light may come on due to temperature changes or changes
in tire pressure from natural air leakage. If the system has not been initialized
recently, setting the tire pressures to factory specifications should turn off the
light.
Seat belts
Take up slack
Too high
Keep as low on
hips as possible
NOTE: If a passenger’s seat belt is fully extended, then retracted even slightly,
the Automatic locking retractor (ALR) will prevent it from being re-extended
beyond that point, unless fully retracted again. This feature is used to help hold
child restraint systems securely.
To find more information about seat belts, and how to install a child restraint
system, refer to the Owner’s Manual.
32
Seat belts-Shoulder belt anchor
Squeeze lock release to lower
OVERVIEW
Doors-Child safety locks
Rear door
Unlock
Lock
Spare tire & tools
Spare tire, jack and tool location
FEATURES/OPERATIONS
Moving the lever downward will allow the door to be opened only from the outside.
Jack and tool
Spare tire
Removing the spare tire
(1)
(2)
(3)
Refer to the Owner’s Manual for tire changing and jack positioning procedures.
33
SAFETY AND EMERGENCY FEATURES
(1) Remove the cover.
(2) Assemble the jack handle.
(3) Insert the jack handle extension into the lowering screw. Lower the spare tire
completely to the ground.
SAFETY AND EMERGENCY FEATURES
Star Safety SystemTM
All new Toyota vehicles come standard with the Star Safety SystemTM, which
combines Vehicle Stability Control (VSC), Traction Control (TRAC), Anti-lock
Braking System (ABS), Electronic Brake-force Distribution (EBD), Brake Assist (BA)
and Smart Stop Technology (SST).
Vehicle Stability Control (VSC)
VSC helps prevent loss of traction during cornering by reducing engine power and
applying brake force to selected wheels.
Toyota’s VSC monitors steering angle and the direction your vehicle is traveling.
When it senses that the front or rear wheels begin to lose traction, VSC reduces
engine power and applies braking to selected wheels. This helps restore traction
and vehicle control.
Traction Control (TRAC)
VSC helps prevent loss of traction during cornering by reducing engine power, and
Traction Control helps maintain traction on loose gravel and wet, icy, or uneven
surfaces by applying brake force to the spinning wheel(s).
Toyota’s TRAC sensors are activated when one of the drive wheels starts to slip.
TRAC limits engine output and applies the brakes to the spinning wheel. This
transfers power to the wheels that still have traction to help keep you on track.
Anti-Lock Brake System (ABS)
ABS helps prevent brakes from locking up by “pulsing” brake pressure to each
wheel. This limits brake lockup and helps provide directional control for the
current road conditions.
Toyota’s ABS sensors detect which wheels are locking up and limits wheel lockup
by “pulsing” each wheel’s brakes independently. Pulsing releases brake pressure
repeatedly for fractions of a second. This helps the tires attain the traction that
current road conditions will allow, helping you to stay in directional control.
Electronic Brake Force Distribution (EBD)
Toyota’s ABS technology has Electronic Brake-force Distribution (EBD) to help
maintain control and balance when braking. Abrupt stops can cause a vehicle
to tilt forward, reducing the braking power of the rear wheels. EBD responds to
sudden stops by redistributing brake force to enhance the braking effectiveness of
all four wheels.
Brake Assist (BA)
Brake Assist is designed to detect sudden or “panic” braking, and then add braking
pressure to help decrease the vehicle’s stopping distance. When there’s only a
split second to react, Brake Assist can add additional brake pressure more quickly
than just the driver alone can.
34
Smart Stop Technology (SST)
SST engages when the accelerator is depressed first and the brakes are applied
firmly for longer than one-half second at speeds greater than five miles per hour.
OVERVIEW
Smart Stop Technology automatically reduces engine power when the accelerator
and brake pedals are pressed simultaneously under certain conditions.
SST doesn’t engage if the brake pedal is depressed before the accelerator pedal,
allowing vehicles to start on a steep hill and safely accelerate without rolling
backward.
Floor mat installation
There are two types of Toyota floor mats: carpeted and all-weather. Each vehicle
has model-specific floor mats. Installation is easy.
To keep your floor mat properly positioned, follow these steps:
Always align the Δ marks
FEATURES/OPERATIONS
• Only use floor mats designed for your specific model.
• Use only one floor mat at a time, using the retaining hooks to keep the mat in
place.
• Install floor mats right side up.
SAFETY AND EMERGENCY FEATURES
35
36
BLUETOOTH® DEVICE PAIRING
SECTION
37
BLUETOOTH® DEVICE PAIRING
To begin the Bluetooth® Pairing process, press the HOME button on the
faceplate of your Toyota Vehicle Entune™ Multimedia Head Unit.1
Bluetooth® Pairing for Android® phone
and Entune™ touch screen system
Pairing your phone is the first step in connecting with your Toyota for hands-free
calling and for audio streaming via Bluetooth. This pairing process is quick and
easy: all Android mobile digital devices have Bluetooth integrated; all you have to
do is setup the phone and multimedia system to “talk” to each other and form a
connection.2
Initiate Bluetooth® on your Android®
STEP 1
From your APPS
SCREEN, select
SETTINGS
STEP 2
Select
CONNECTIONS and
select BLUETOOTH
STEP 3
STEP 4
Ensure
BLUETOOTH
is ON
Select YOUR PHONE
DEVICE to make it
discoverable.
Phone will seek out
Bluetooth devices while
remaining discoverable.
STEP 5
While your Android device is seeking
out Bluetooth devices, proceed to
your Entune Multimedia Head Unit on
your Toyota vehicle.
1 To determine which head unit is installed in your vehicle, refer to the Audio section in this guide.
2 Some Android devices may have slightly different SETTINGS screen layout depending on manufacturer of
device and Android OS version.
38
Initiate Bluetooth® on your Entune™ Multimedia Head Unit
Once you have Bluetooth enabled on your phone and ready to pair, you will need
to initiate Bluetooth on your Entune head unit. Please follow the instructions
below to pair your Bluetooth enabled phone to your Entune system.
STEP 6
On your Toyota Vehicle
Entune Multimedia Head Unit,
Select SETUP BUTTON on the
Home Screen.
STEP 9
Back on your smartphone,
you can now select your
TOYOTA VEHICLE in
Bluetooth Settings.
STEP 7
STEP 8
Select BLUETOOTH
STEP 10
Select ADD, to add your
phone device
STEP 11
Your smartphone is now
paired with Entune.
You may need to enter the provided
Bluetooth PIN on your phone.
39
Once paired, Entune will
attempt to connect audio and
contacts on your phone.
BLUETOOTH DEVICE PAIRING
Initiate Bluetooth® on your Entune™ Multimedia Head Unit (continued)
STEP 12
STEP 13
Using your smartphone, you
will need to allow Entune
access to your messaging
and contacts
A confirmation will
appear once your phone
has been paired and
connected.
It is recommended to check the
“Don’t ask again” box, so as not
to have to press OK every time the
phone makes a Bluetooth connection
with your Toyota
Additional Resources
If you’re having trouble pairing your phone, Toyota has you covered. You can get
more information from the following sources:
Online Pairing Guide:
www.toyota.com/connect
Your Toyota Owner’s Manual
Located in the vehicle glovebox
Toyota Customer
Experience Center
(800) 331-4331
Disclosures
This brochure is accurate at the time of print; content subject to change based on periodic multimedia software updates.
1. Concentrating on the road should always be your first priority while driving. Do not use the hands-free phone system if it
will distract you.
2. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by
Toyota is under license. A compatible Bluetooth enabled phone must first be paired. Phone performance depends on
software, coverage & carrier.
3. Android is a trademark of Google, Inc.
4. Apps/services vary by phone/carrier; functionality depends on many factors. Select apps use large amounts of data; you
are responsible for charges. Apps & services subject to change. See Toyota.com/entune for details.
40
Bluetooth® Pairing for iPhone® and
Entune™ touch screen system
Pairing your phone is the first step in connecting with your Toyota for hands-free
calling and for audio streaming via Bluetooth. This pairing process is quick and
easy: all iPhone mobile digital devices have Bluetooth integrated; all you have to
do is setup the phone and multimedia system to “talk” to each other and form a
connection.
Initiate Bluetooth® on your iPhone®
STEP 1
From the HOME
SCREEN, select
SETTINGS
STEP 2
Select BLUETOOTH
STEP 3
STEP 4
Ensure
BLUETOOTH
is ON
Your iPhone will seek
out Bluetooth devices
while remaining
discoverable
STEP 5
While your iPhone device is seeking
out Bluetooth devices, proceed to
your Entune Multimedia Head Unit on
your Toyota vehicle.
CONTINUE ON THE NEXT PAGE...
41
BLUETOOTH DEVICE PAIRING
Initiate Bluetooth® on your Entune™ Multimedia Head Unit
Once you have Bluetooth enabled on your phone and ready to pair, you will need
to initiate Bluetooth on your Entune head unit. Please follow the instructions
below to pair your Bluetooth enabled phone to your Entune system.
STEP 6
Select SETUP BUTTON on the
Home Screen.
STEP 9
Back on your smartphone,
you can now select your
TOYOTA VEHICLE in
Bluetooth Settings.
STEP 7
STEP 8
Select BLUETOOTH
STEP 10
Select ADD, to add your
phone device
STEP 11
Your smartphone is now
paired with Entune.
You may need to enter the provided
Bluetooth PIN on your phone.
42
Once paired, Entune will
attempt to connect audio and
contacts on your phone.
STEP 12
STEP 13
Using your smartphone, you may need to
allow Entune access to your messaging
and contacts
A confirmation will
appear once your phone
has been paired and
connected.
Only current iPhone text messages can be viewed on
the head unit. iPhone does not allow text message
reply.
Additional Resources
If you’re having trouble pairing your phone, Toyota has you covered. You can get
more information from the following sources:
Online Pairing Guide:
www.toyota.com/connect
Your Toyota Owner’s Manual
Located in the vehicle glovebox
Toyota Customer
Experience Center
(800) 331-4331
Disclosures
This brochure is accurate at the time of print; content subject to change based on periodic multimedia software updates.
1. Concentrating on the road should always be your first priority while driving. Do not use the hands-free phone system if it
will distract you.
2. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by
Toyota is under license. A compatible Bluetooth enabled phone must first be paired. Phone performance depends on
software, coverage & carrier.
3. Apps/services vary by phone/carrier; functionality depends on many factors. Select apps use large amounts of data; you
are responsible for charges. Apps & services subject to change. See Toyota.com/entune for details.
43
BLUETOOTH DEVICE PAIRING
Bluetooth® Pairing for Windows Phone®
and Entune™ touch screen system
Pairing your phone is the first step in connecting with your Toyota for hands-free
calling and for audio streaming via Bluetooth. This pairing process is quick and
easy: all Windows Phone mobile digital devices have Bluetooth integrated; all you
have to do is setup the phone and multimedia system to “talk” to each other and
form a connection.
Initiate Bluetooth® on your Windows Phone®
STEP 1
From your APP LIST,
select SETTINGS
STEP 2
Select BLUETOOTH
STEP 3
STEP 4
Ensure
BLUETOOTH
is ON
Phone will seek out
Bluetooth devices
while remaining
discoverable
STEP 5
While your iPhone device is seeking
out Bluetooth devices, proceed to
your Entune Multimedia Head Unit on
your Toyota vehicle.
44
Initiate Bluetooth® on your Entune™ Multimedia Head Unit
Once you have Bluetooth® enabled on your phone and ready to pair, you will need
to initiate Bluetooth® on your Entune head unit. Please follow the instructions
below to pair your Bluetooth enabled phone to your Entune system.
STEP 6
On your Toyota Vehicle
Entune Multimedia Head Unit,
Select SETUP BUTTON on the
Home Screen.
STEP 9
Back on your smartphone,
you can now select your
TOYOTA VEHICLE in
Bluetooth Settings.
STEP 7
STEP 8
Select BLUETOOTH
STEP 10
Select ADD, to add your
phone device
STEP 11
Your smartphone is now
paired with Entune.
You may need to enter the provided
Bluetooth PIN on your phone.
45
Once paired, Entune will
attempt to connect audio and
contacts on your phone.
BLUETOOTH DEVICE PAIRING
Initiate Bluetooth® on your Entune™ Multimedia Head Unit (continued)
STEP 12
STEP 13
Using your smartphone,
you may need to allow
Entune access to your
contacts
A confirmation will
appear that your phone
has been paired and
connected.
Additional Resources
If you’re having trouble pairing your phone, Toyota has you covered. You can get
more information from the following sources:
Online Pairing Guide:
www.toyota.com/connect
Your Toyota Owner’s Manual
Located in the vehicle glovebox
Toyota Customer
Experience Center
(800) 331-4331
Disclosures
This brochure is accurate at the time of print; content subject to change based on periodic multimedia software updates.
1. Concentrating on the road should always be your first priority while driving. Do not use the hands-free phone system if it
will distract you.
2. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by
Toyota is under license. A compatible Bluetooth enabled phone must first be paired. Phone performance depends on
software, coverage & carrier.
3. Apps/services vary by phone/carrier; functionality depends on many factors. Select apps use large amounts of data; you
are responsible for charges. Apps & services subject to change. See Toyota.com/entune for details.
46
NOTES
47
NOTES
48
2016
Sequoia
NOTES
This Quick Reference Guide is a summary of basic vehicle
operations. It contains brief descriptions of fundamental operations
so you can locate and use the vehicle’s main equipment quickly
and easily.
The Quick Reference Guide is not intended as a substitute for the
Owner’s Manual located in your vehicle’s glove box. We strongly
encourage you to review the Owner’s Manual and supplementary
manuals so you will have a better understanding of your vehicle’s
capabilities and limitations.
Your dealership and the entire staff of Toyota Motor Sales, U.S.A.,
Inc. wish you many years of satisfied driving in your new Sequoia.
A word about safe vehicle operations
This Quick Reference Guide is not a full description of Sequoia
operations. Every Sequoia owner should review the Owner’s
Manual that accompanies this vehicle.
Pay special attention to the boxed information highlighted in
color throughout the Owner’s Manual. Each box contains safe
operating instructions to help you avoid injury or equipment
malfunction.
All information in this Quick Reference Guide is current at the
time of printing. Toyota reserves the right to make changes at
any time without notice.
49
SEQUOIA
2 0 1 6
CUSTOMER EXPERIENCE CENTER
1-800-331-4331
QUICK REFERENCE GUIDE
Printed in U.S.A. 7/15
15-TCS-08583
00505QRG16SEQ
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement