Morris MDM-3018 - 30Lt DEHUMIDIFIER Instructions manual

Morris MDM-3018 - 30Lt DEHUMIDIFIER Instructions manual
MULTIFUNCTIONAL AIR
TREATMENT UNIT MANUAL
MODEL MDM-3018
VERY IMPORTANT
Do not install and use your portable Air Treatment
Unit before carefully reading this instruction guide.
Please retain this manual brochure for product
warranty and future reference
CAUTION
1. " PLEASE MAKE SURE THE PRODUCT
VENTILATES ALL THE TIME "! Please make sure
the inlet and outlet ventilation is not blocked at all
times.
2. Operate this unit on a horizontal surface to avoid
water leakage.
3. Do not operate this unit in an explosive or
corrosive atmosphere.
4. Operate this unit in an ambient of 32 degree
centigrade or less.
5. Clean air filter periodically to enjoy the most
efficient cooling.
6. When the unit is shut off, please wait at least 3.5
minutes before restarting this is to prevent the
compressor from being damaged.
7. This unit needs at least 7 Amps of electricity to
have its compressor operational. To avoid the
household electricity block out, please do not
use any extension cord for this unit.
8. This unit is for indoor cooling, humidifying,
dehumidifying and air filtering (optional).
1
9. When turning on the unit at the first time, the
cool air outlet stepper motor will operate and
then the fan motor and the compressor will start
up. The compressor will work after 3.5 minutes
operating hereafters.
10. When the supply cord is damaged, it must be
replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid
hazard.
11. In order to dispose the appliance safely, please
remove the batteries from the unit before
scrapping it.
12. This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.
13. Please drain off water when moving the unit.
14. Do not install the unit in the laundry room.
15. The unit should be installed according to the
national wiring rules.
16. The heating function of the unit should be operated
in an indoor ambient temperature between 5℃ and
23℃.
17. This unit is only suitable for personal use in limited
area.
2
ATTENTION
For effective hot air and cooling functions, please
ensure that the following steps are undertaken:
1)
Extend the exhaust hose to a length of not
more than 400mm. The exhaust hose must
be kept parallel and must not be bent up or
down.
2)
A distance of 500mm minimum must be
kept between the filter side of the unit and
wall or any other obstacles”.
3)
When this appliance starts to defrost, the
word “DF” will be displayed .
4)
To enjoy the hot air, please take down the hot
outlet connector and exhaust pipe(as fig 2)
when the unit starts cooling, face to the hot air
outlet and then enjoy the hot air.
CONGRATULATIONS ON YOUR
SELECTION OF A QUALITY
MULTIFUNCTIONAL AIR TREATMENT UNIT
This Air Treatment Unit has been designed and manufactured to the
highest standards of modern engineering.
Our product not only provides you a remote control to help user
operate all the functions easily and conveniently but also has below
benefits:
3
air
- Moves easily from room to room on easy glide castors
- No installation required-just plug into any household power
outlet
- Powerful refrigerated air system cools down the ambience
instantly whenever you want.
- Dehumidified and filtered air cycle improve breathing
environments effectively.
- Besides the remote control, your one touch electronic pad also
provides easy-identifying manual operation.
- 24 hour programmable timer that can be used with either the
air conditioning or dehumidification setting
- Unique sleep control function, dehumidification,
humidification and air purification.
- 220-240 Volt 50Hz operation
- 1.8 meter cord with plug
UNPACKING INSTRUCTIONS
1.
Place the unit in the correct upright position before unpacking.
2.
Cut the two packing straps.
3.
Slide the carton in an upwards motion and it will release from the base.
4.
Lift the unit carefully to make it slides out of the foam
base.
5.
Pull out the water tank and take out the exhaust hose
as the picture.
6.
Install the exhaust hose on the unit before operating
the unit.
4
CONTENTS
1 / Air conditioner unit
2 / Remote control
3 / User manual
4 / Window Kit A
NAME OF THE PARTS
1.
Control panel
2.
Remote control
receiver
3.
Filter of EVA
4.
Air outlet
5.
Air inlet(left)
6.
Joint tube
7.
Exhaust hose
8.
Remote control
location
9.
Filter of COND
10. Air inlet(right)
11. Exhaust air outlet
12. Exhaust air outlet joint
13. Filler
14. Drain hole
15. Water tank
5
CONTROL PANEL & DESCRIPTION OF FUNCTION
6
1.
POWER
KEY
Press to turn unit "ON" or "OFF"
2.
FUNCTION
Press this key to select dehumidifying, cooling, heating, humidifying, air delivery or
air purification.
3.
TEMPERATURE REGULATION KEY
(+)
During cooling function:This key raises the preset temperature by 1℃ each time it
is pressed and the maximum limit is 30℃.
During heating function:This key raises the preset temperature by 1℃ each time it
is pressed and the maximum limit is 25℃.
During dehumidifying & humidifying function:This key raises the preset humidity by
5% each time it is pressed and the maximum limit is 90%.
4.
TEMPERATURE REGULATION KEY
(-)
During cooling function:This key lowers the preset temperature by 1℃ each time it
is pressed and the minimum limit is 17℃.
During heating function:This key lowers the preset temperature by 1℃ each time it
is pressed and the minimum limit is 15℃
During dehumidifying & humidifying function:This key lowers the preset humidity by
5% each time and the minimum limit is 30%
HUMIDITY SETTING:
“CO”(continuous)→30%→35%→40%→45%→50%→55%
→60%→65%→70%→75%→80%→85%→90%→“CO”
(continuous)circulation.
5.
LCD
DISPLAY
The display indicates the current setting temperature or the timer setting. When the
set temperature or the timer is adjusted, the new setting is shown then the display
returns the current set temperature.
7
※ The display is also used to show error codes should a fault occur, see ERROR
CODES.
6.
Press
SPEED
to select either LOW, HIGH or AUTO fan speed.
If "AUTO" is selected (During cooling function),”HIGH” or "MEDIUM" or “LOW" will
be selected automatically according to the difference between setting temperature
and ambient temperature.
The unit will be running on high speed if the ambient temperature higher than the
setting temperature for 2℃. The unit will be running on low speed if the ambient
temperature is same with the setting temperature.
7.
PROGRAMMABLE
TIMER
TIMER-ON: The timer-on is
used to turn on the unit automatically after
the set time is over.
1. Press the "TIMER" key at stand-by status to set the time you desired.
2. Once the set hour has come to an end, the unit will turn on automatically.
3. Press the "POWER" key before time out, the setting time will be canceled and
the unit will turn on.
4. You can set the function and fan speed while setting the timer.
TIMER-OFF: The timer-off is used to turn off the unit automatically after the setting
time is over.
1. Press the "TIMER" key at operating status to set the time you desired.
2. Once the set hour has come to an end, the unit will turn off automatically.
3. Press the "POWER" key before the time out, the setting time will be canceled
and the unit will turn off.
8.
FAN FUNCTION
During this mode, the unit only runs for the fan without involved the operation of
compressor & water pump. The fan speed can be set from the panel.
9.
DEHUMIDIFICATION
When ambient humidity is lower than setting humidity by 2%, compressor will stop
automatically for 3.5 minutes, and return working until the ambient humidity is higher
than setting humidity by 2%.
8
10. HUMIDIFICATION
1. The unit will stop automatically after four hours operating in this mode. Please put
some water (Approx 0.8L) into the filler and turn it on again.
2. The unit will stop humidifying if ambient humidity is equal to the pre-set humidity.
Otherwise it will work as the humidifying procedure1.
3.
The fan motor and water motor will work, but compressor doesn’t work.
11. PURIFICATION
Ionizer function will
auto start when unit work. When select this function,
the purification indicator light will be on and only the fan motor works.
When the fan motor’s life time is larger than 2000hrs,the indicator light will flash,
and LCD display E8, it means the filter should be changed; Change the active
carbon filter and press SPEED button for 3 seconds and alarm reset.
12. SLEEP CONTROL
FUNCTION
1. While in cooling mode, press
the SLEEP key to set the temperature. It
increases1 ℃ after an hour and at most increases 2 ℃ after 2 hours.
2.
Press the SLEEP key again can cancel the setting.
13.
SWING
Press
this key and the outlet will oscillate and it will stop when this key
is pressed again. The outlet will close up automatically when the unit stops
working.
14. HEATING FUNCTION WILL START
(1) Heating function , temperature setting range
PTC
is 15~25℃
(2) Temperature can be set, when the environment temperature is lower than
setting temperature, it will start heating
(3) PTC will work only when the environment temperature<25℃
15. ALARM
When the water tank is full,"E4" will be displayed on the display panel. To resume
operation, please remove the rubber cap of the drain hose to drain out the water
firstly. The E4 warning will disappear after draining, and then you can restart the
unit by pressing the POWER key.
16. CHILD
LOCK
Press“+”and“-”at the same time for three seconds, the unit
will enter child lock function, and it will be unlocked by pressing the two buttons
again.
9
REMOTE CONTROL FUNCTION
On/Off switch
Function “MODE” selector
Hourly programming
Automatic fan speed
High fan speed
Low fan speed
Night operation selector
Temperature selector
Swing
10
NOTICE
This unit can evaporate the condensation and distribute through the exhaust hose
automatically.
1.
When the unit is in the cooling function, it does not need the drain pipe installed.
Please make sure that the rubber cap① is locked on drain hole, when the unit is
running.
2.
When operating the dehumidifying function the “①” rubber cap on drain hose
should be pulled out and install a proper drain hose②,please remove the air
exhaust hose, connect a drain hose to the drain hole and lead the water to the
outside in order to intensify dehumidifying capacity.
※ When the water tank is full,"E4" will be displayed on the display panel. Please
remove the rubber cap“②” of the drain hole to drain out the water first. After the
drainage is completed, please restart the unit and then the unit can operate
normally.
3.
During the humidifying process, Please make sure the stopper is fixed well on the
drain hole, pour water into the filler(as fig 1), this unit has innovative inner structure,
the redundant water will flow into the water tank and the display screen will show
E4 if the water tank is full. Stop pouring water and shake the unit gently, dry the
water tank and reload the water tank, press the power button and restart the unit.
11
MAINTENANCE
PLEASE DISCONNECT THE POWER CORD
BEFORE CLEANING.
AIR FILTER
1. The air filter located on both sides of the unit can be
removed simply by pulling the frame out.
2. Wash the filter with cool water (cooler than 40℃)
every two weeks, and put filter back after it air-dried naturally.
CONDENSER/EVAPORATOR
Use a brush attachment with a vacuum cleaner.
Casing
Wipe with a damp cloth and polish with a soft cloth.
When cleaning the filter, please remove it as the picture.
POWER SUPPLY
(1) Confirm the correct power.
(2) Insert the plug into the outlet firmly In order to prevent any dangerous
leakage.
(3) Don’t pull power wire by force because it will cause damage to power wire.
12
PLACE FOR USE
(1) Because the machine distributes hot air, please don’t place or operate in a
narrow place.
(2) In case of dangerous leak, don’t work the machine in a humid place.
(3) Don’t place the machine in a sunlit corner otherwise the unit might shut
down due to the overheat and the color of the machine may soon fade out.
HELPFUL HINTS
The unit is fitted with a special thermal cut off device.
Please ensure the unit is not placed against objects which will obstruct air
intake e.g. furniture or curtains as this will affect it's performance dramatically.
WINDOW KIT INSTALL

Install the Exhaust Hose and the Adjustable Window Slider Kit as
depicted in Fig.1 & Fig.1a.
13
EXHAUST HOSE INSTALL
1. Take out the joint tube from the exhaust pipe(see picture ①) and fix a part and b part
together.
2. Please take out the hot air outlet joint and put the right side filter into the hot air inlet.
1. Rotate the joint tube counterclockwise and fix it with the exhaust pipe(see arrow①).
2. Fit the pipe joint on the unit as arrow ② .
3. Please to install the exhaust hose onto the unit see instruction arrow ③
4. Please to discharge the exhaust hose onto the unit see instruction arrow ④
14
TROUBLE SHOOTING
Problem
Cause
E1
Electrical short on both
temperature sensor and
PCB(environment)
Electrical short of
temperature sensor copper
tube and PCB wiring(coil)
Indicates water tank full or
possibly the incorrect
wiring of plug
Contact an electrician for repair
Filter’s life time is larger
than 2000hrs
Change the filter and press SPEED button
E2
E4
E8
Trouble shooting
Contact an electrician for repair
User needs to pull out the rubber stopper
which is located at the bottom of the unit, to
drain the water away. Check that the plug
has been wired correctly.
for 3 seconds and alarm reset.
15
SPECIFICATION
Model No.
Power Source
MDM-3018
220-240V~50Hz
Rated Power (EN60335)
Cooling
Heating
590W
700W
PTC Heater Power
600W
Cooling Capacity
1100W
Heating Capacity
600W
Moisture Removed
30 liters/day
Humidifying capacity
0.2L/H
Refrigerant
R410A
Water Tank Capacity
Dimensions (mm)
2.6L
375Wx280Dx505H
(CE) N 842/2006:
R410A is a kind of fluorinated greenhouse gases covered by
the Kyoto Protocol.
R410A is total global warming potential (GWP) is 2088.
16
NOTICE ABOUT RECYCLING
Your product is designed and manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their
end-of-life, should be disposed of separately from your household waste.
Please dispose of this equipment at your local community waste
collection/recycling centre. In the European Union there are separate
collection systems for used electrical and electronic products.
Please help us to conserve the environment we live in!
DECLARATION OF CONFORMITY
Herewith, Amiridis-Savvidis S.A. states that model MDM-3018, complies with the
requirements of below directives:
EMC-Directive: 04 / 108 / EC
Low Voltage Directive: 06 / 95 / EC
RoHS2 Directive: 11 / 65 / EU
The detailed declaration of conformity can be found at www.morris.gr
EXCLUSIVE IMPORTER IN GREECE:
Amiridis – Savidis S.A.
87A, 17th November Str - P.C. 55534
Pylaia - Thessaloniki - Greece
T: 2310944944 | F: 2310944940
www.amiridis-savvidis.gr
www.united-electronics.gr
17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement