Installation guide DOC.IG.BQC40.1 Rev. 3 Bettis Q-Series Control Module QC40 AS-Interface Bettis Q-Series May 2018 Bettis Q-Series Installation guide May 2018 1 DOC.IG.BQC40.1 Rev. 3 Applicable Control Modules QC40 - AS-Interface Weather proof IP66/ NEMA4X QC40 - AS-Interface Non-Incendive or Non Sparking Note: These variations can be equipped with one or two pilot valves: * One pilot valve is default and suitable for normal operation of double acting or spring return actuators. * Two pilot valves are required for Fail in Last Position function on double acting actuators. The enclosures have a IP66 or NEMA 4X, ingress protected rating. 2 Before starting * Actuator must be isolated both pneumatically and electrically before any (dis)assembly is begun. * Hazards related to the control of external processes under measurement, are beyond the scope of of the content described in this document. * Installation, adjustment, putting into service, use, assembly, disassembly and maintenance of the control module must be done by qualified personnel. * Do not install, operate, or maintain a Q series control module without being fully trained and qualified in valve, actuator, and accessory installation, operation, and maintenance. * To avoid personal injury or property damage, it is important to carefully read, understand, and follow all of the contents of this manual, including all safety cautions and warnings. * Be sure that the actuator is correctly mounted before connecting air supply and electrical wiring (see Installation & Operation Manual Bettis Q-Series Valve Actuator, DOC.IOM.BQ.E) * Check the module label for the right execution (see figure 2.2) * Check the type of actuator: single or double acting (see figure 2.2). * For mechanical installation of the module see installation instruction leaflet DOC.QC4.MTI.1, as shipped with the module. * If you have any questions regarding these instructions, contact your Emerson sales office before proceeding as shipped with the module. 1 Control Module Label = 2 QC40..WP.. = ASI OK QC40..x4.. = ASI Non Incendive / Non Sparking OK Actuator Label = QS xxxx = Single acting (Spring Return) QD xxxx = Double acting Note: x is variable based on the certification type. Fig. 2.1 Check proper mounting before connecting air supply and electrical wiring. 2 Fig. 2.2 Identification Installation guide Bettis Q-Series DOC.IG.BQC40.1 Rev. 3 2.1 May 2018 Mechanical alignment and mounting of the control module (1) The control module is equipped with an alignmentedge on top of the module. This allows easy alignment and mounting of the control module on to the actuator housing. Alignment-edge Alignment-edge Procedure: (see figure 2.3) 1. First take care that both mating faces from the actuator and control module are clean and free of dirt. 2. Check if the module has the required function 3. Remove the transparent film from the control module. 4. Ensure seals are placed correctly. 5. Level the screws with the surface. 6. Place the alignment-edge (1) of the control module at the top of the pneumatic interface. 7. Flip the module down taking care that the IPT Probe (2) on the actuator fits in the mating hole on the control module and loosely place the screws. 8. Tighten screws according force in sequence. Tightening moments IPT probe (2) Fig. 2.3 Alignment and mounting of control module to actuator The Control Module should be fastened by using an Allen key and applying the following tightening moments: - Allen Key: No 5 Torque: 6.1 to 6.6 Nm (54 - 58.4 In.lbs) Terminal compartment with: - AS-I cartridge and - switch cartridge Lockable Control Module Type Label Option: 1 or 2 speed control throttles Module cover Pneumatic connections Option: Local Manual Control Option: Additional Local Manual Control for “Fail in Last Position” Fig 2.4 Control module overview 3 Bettis Q-Series Installation guide May 2018 3 Pneumatic connections IMPORTANT 1 The actuator/valve combination can move after connecting the air supply. 2 Ensure that the QC40 control modules are mounted properly to the actuator to achieve good functioning and the required ingress protection, before connecting the air supply. 3 Check that the maximum supply pressure Pmax = 8bar/116Psi 4 Be sure that the minimum required supply pressure for the application is available at the actuator. 5 Take appropriate measures to prevent condensation or moisture to entering the actuator or the control module. Condensation or moisture can damage these components and can result in failures. 6 The exhaust ports Ra and Rb on the module (see figure 3.1) are shipped from the factory with transport protection. * If ingress protection IP66 or NEMA 4X is required, appropriate connections must be used in exhaust ports Ra & Rb. 3.1 * * * * Single acting Ra Control Ps Module cover 1/4” BSP or 1/4” NPT Double acting Ra Rb Ps 1/4” BSP or 1/4” NPT Fig. 3.1 Pneumatic connections Operating media : Air or inert gasses. Air filtered at 50μm. Dew point 10 K below operating temperature. For subzero applications take appropriate measures. 3.2 50µm Single acting (spring return) or Double acting actuator : 1 Remove the transport sticker from the air supply (Ps). 2 Connect air supply to port (Ps). 4 DOC.IG.BQC40.1 Rev. 3 OK Fig 3.2 Install drip loops Installation guide Bettis Q-Series DOC.IG.BQC40.1 Rev. 3 4 May 2018 Electric Connections Table 4.1 Electrical data QC40 - ASI Protocol AS-Interface Spec3.0 Maximum Voltage 31.6V Minimum Current 34mA at 26.5V (pilot valves off) Nominal Current (one pilot valve activated) 85mA at 26.5V Maximum Current Consumption 125mA at 26.5V (one pilot valve application) Maximum Current Consumption 140mA at 26.5V (two pilot valves application) Protection Short circuit detection Note: The current consumption of feedback switches is included. Check the product data sheet for one or two pilot valves application. Environmental conditions : Ambient: -25°C to +60°C Temperature * (-4°F to +140°F) Maximum Surface: 80°C (176°F) 0 to 85% at 25°C(+77°F) derate Humidity to 50% above 40°C (104°F) (non-condensing). Operating full power available Altitude up to 2000 meter (6000 feet). Use In- and outdoor. * The current restricted power supply meets NEC Class 2, as described by the National Electrical Code® (ANSI/NFPA 70 (NEC®)) * In case the Control module is used in Hazardous locations, check the Control Drawings as per chapter 10 for the applicable temperature range. Table 4.2 Wiring dimensions Wire type: Dimensions: Cable range 0.33 - 2.5mm2 or 22 - 12AWG Please check www.as-interface.net for various application guides like installation and wiring guidelines. Table 4.3 Tools Screw: Terminals Earth screws Tool: Screw driver: 0.6 x 3.5 Screw driver for cross slotted Phillips screws nr. 2. WARNING: * If the Control Module is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. * If required, mount earth wire (1) between top (2) and bottom (3) ring of earth wire connection (see figure 4.1). 4.1 Electrical data for hazardous area executions Please check chapter 10 for electrical data and instructions in case an “Non Incendive/Non Sparking” Control Module is used in hazardous locations (Zone 2 or Class I Div.2). Fig. 4.1 Earth wire connections 5 Bettis Q-Series Installation guide May 2018 4.2 DOC.IG.BQC40.1 Rev. 3 Procedure Control Module Terminal compartment 1 Remove Control Module cover (see figure 4.2). 2 Guide the cable(s) through the electrical entry(ies). - Use and mount cable glands as required by national or local legislation. Type Label Lockable Module cover - When IP66/NEMA4X ingress protection is required, the electrical entries must be fitted with glands rated IP66/NEMA4X or higher. 3 Make the electrical connections as shown in figure 4.3. - For hazardous area connections, see the instructions in chapter 10 Electrical entries: 3/4”NPT or M20 - Quick connectors, as shown below, are allowed to be used only for non-explosion safety product application 4 Mount the function module cover to the housing (see figure 4.2) or continue with chapter 5. Take care that the cover seal is in place to comply to dust and water tightness according to IP66 / NEMA4X. LED’s for Fault, Power, Open and Close position FAULT POWER 1/2”NPT or M20 Wiring Terminals Fig. 4.2 Terminal connections behind cover. AS-I terminal wiring connections: QC40 AS-I control module Field wiring Actuator wiring + 1 AS-I Power 2 - 3 supply Note: Terminal 2 can be used for shield. Quick connector pinouts: (male chassis part) 1 3 4 1 2 4 2 7/8" UNC 1 3 3 M12 Brown Blue 1 2 3 Quick Terminals connector option Connect only the brown and blue wires. Where applicable, cut away unused wires. Fig. 4.3 Terminal connections and quick connector pinouts 6 Installation guide Bettis Q-Series DOC.IG.BQC40.1 Rev. 3 5 May 2018 Commissioning In order to commission the QC40 ASI Control Module, the following actions must be considered or done: 5.1.2 Before re-adjusting the limit switch points 1 Re-adjustment of the limit switch points if the factory setting do not meet the application requirements 2 Addressing of the QC40 ASI Control Module * Before mounting the actuator on the valve, be sure that both the actuator and the valve have the same “open” or “closed” position. * Set the Mechanical stroke before setting the limit switches. 5.1 Re-adjustment of the limit switch points 5.1.1 Factory switch point settings Mechanical stroke: 90°±0.5° (Actuator setting) Switch points: ± 15° before each end of stroke (open and closed position, see fig 5.1). Adjustable range: -20° to +3° at each end. 20° 3° Switch points IMPORTANT 5.1.3 Pneumatic and electrical connections Make pneumatic and electrical connections before adjusting the limit switch setting. See chapter 3 and 4. 5.1.4 Switch point setting and valve rotation direction. The QC40 ASI Control Module is equipped with non-intrusive switch point adjustment. The adjustment screws are accessible behind a shield in the front of the module (see fig 5.2). This means that the switch point adjustment can be done without opening the module. Closed 90° Normally valves are “Closed” after a clock wise rotation. - 20° Open 3° Fig. 5.1 Adjustable range If required the mechanical stroke and the limit switch setting can be re-adjusted. - For mechanical stroke adjustment of the actuator, please see document DOC.IOM.BQ.E, available from www.emerson.com/bettis. For re-adjusting the limit switches, see procedure below. - In this case the top adjustment screw (see fig. 5.2), sets the switch point of the “Closed” position and bottom adjustment screw sets the switch point of the “Open” position. For a valve that is “Open” after a clock wise rotation, the position feedback will be reversed. The table below indicates which re-adjustment screw is related to the “Open” or “Closed” switch point setting. Table 5.1 Re-adjustment screws Re-adjustment screw : Bottom Top Valve movement “Close” after “Open” after a clock wise a clock wise rotation rotation Open position Close position Close position Open position 7 Bettis Q-Series Installation guide May 2018 DOC.IG.BQC40.1 Rev. 3 The lever is of the “floating” type. When the IPT device operates the lever, it moves completely upwards until it meets the upper pivot block (4). At this point the lever will tip over and pull down the switch operating rod (5) and operates the bottom switch (7). When the IPT device moves back the springs cause the lever to move completely downwards until it meets the lower pivot block (2). At this point the lever will tip over and push up the switch operating rod (5) and operates the top switch (8). 5.1.5 Working principles Switch Operating Mechanism (see fig 5.2) The Switch Operating Mechanism is intend to operate the position feedback switches and allows adjustment of the switch points in the open and closed end positions. Factory setting is that the switches are activated 15° before the end of the open and closed stroke. Switch Operation The rotation of the actuators pinion operates the IPT device (1) which results in a linear movement. The linear movement of the IPT device operates lever (3). The lever amplifies the linear movement of the IPT device and operates the switch operating rod (5). Dowel pin (6) in the rod operated the levers of the open and closed switch elements (8 & 9). Switch point adjustment The position of the lower pivot block (2) can be changed by adjustment screw (10) and the position of the upper pivot block (4) can be changed by adjustment screw (9). By adjusting the position of these pivot blocks the switch points will be changed. The adjustment screws (9 & 10) can be found behind the shield (12) in front of the module. To access the adjustment screws loosen the screw (11) and rotate the shield (12) as shown. 6 7 9 4 3 2 5 1 Fig. 5.2 Working principles Switch Operating Mechanism 8 DO NO T 15 10 9 11 12 ED GIZ 8 N WHEN E NING N PE O WAR !- ER 10 Installation guide Bettis Q-Series DOC.IG.BQC40.1 Rev. 3 5.1.6 Re-adjustment of switch points IMPORTANT The procedure below assumes: - That the actuator and control modules are according the factory settings. - If the switch setting is somehow lost or forgotten, then consult paragraph 6.3 to set the switch point setting back to factory setting. - That the actuator / valve assembly is closed after a clock wise rotation (see chapter 5.1.4). Below procedure assures that the position feedback complies more accurately with the valve position and will set the switch point at approximately 4° before the end of the stroke. To set and detect the Open or Closed switch points, the QC40 AS-I module has two LED’s that light up if the Open or Closed position limit switch is activated. May 2018 7. Turn bottom screw (4) counter clock wise (do not force the adjustment screw) until the switch trips and the corresponding LED (6) goes on. This position represents the actual “open” position of the valve. 8. Turn the screw minimal a 1/2 turn counter clock wise. The “open” position switch point is now set. 9. Turn the shield (2) back over the adjustment screws and fasten it with the screw (1). Important: During switch point adjustment, do not force the adjustment screws when you feel an obstruction. Forcing the adjustment screws can damage the cross head of the adjustment screw. Table 5.2 Tool table Shield screw Adjustment screws Cross slotted Phillips nr. PH2 0.6 x 3.5 or Cross slotted Phillips nr. PH2 Procedure (see fig 5.3): 1. Loosen the screw (1) of the shield (2) and turn the shield down. 5 Closed Position: 5. Send an “Open” command to the ASI module, wait and make sure the valve has moved to open position. 6. Turn bottom screw (4) clock wise (do not force the adjustment screw) until the switch trips and the corresponding LED (6) goes out. POWER 3 2. Send an “Close” command to the ASI module, wait and make sure the valve has moved to closed position. 3. Turn top screw (3) counter clock wise (do not force the adjustment screw) until the switch trips and the corresponding LED (5) goes out. 4. Turn top screw (3) clock wise (do not force the adjustment screw) until the switch trips and the corresponding LED (5) goes on. This position represents the actual, mechanical “closed” position of the valve. 5. Turn the screw minimal a 1/2 turn clock wise. The “closed” position switch point is now set. Open Position: FAULT 6 4 1 2 “Closed” FAULT Switch point adjustment POWER 5 FAULT POWER 6 “Open” Switch point adjustment Note: 360° rotation of adjustment screw is ±8° adjustment of switch point. Fig. 5.3 Re-adjustment screws for “Open” and “Closed” position feedback 9 Bettis Q-Series Installation guide May 2018 5.2 DOC.IG.BQC40.1 Rev. 3 Addressing 5.2.2 Diagnostics The QC40 ASI module supports the ASI-3 profile. When a module ships from the factory, it has the slave address “0”. The slave address can be changed using a master device. Please check the applicable sections of the documentation supplied with these devices. Table 5.2.1 Factory address IO-Code ID-Code Programming notes: 00 EID1 6 EID2 A Parameter - 7 E 00 The ASI communications watchdog is activated. The control electronics in the module are monitored for short circuit. Diagnostics information is communicated via ASI slave status LEDs and Master (see table 3) Red Green Q-Series data bits Type D0 Bi-directional D1 Bi-directional D2 D3 Bi-directional Bi-directional Table 5.2.2 Symptom Normal operation Functions DI’s Feedback “Closed” Feedback “Open” Not used Not used DO’s Solenoid 2 Control Solenoid 1 Control POWER FAULT POWER Fig. 5.4 ASI slave status LEDs ASI slave status LEDs (see figure 5.4) Indication at the slave LEDs Flags in the master Possible reason Green Red Config. Error Periphery Fault On Off reset reset Everything OK On On set reset Master in STOP Mode undefined Short circuit or line break No data exchanges Serious peripheral error On with reset 10 FAULT Blinking set Suggested action -/Check master configuration “Slave not in LPS Slave with wrong IO/ID Check slave Reset at Slave active configuration Slave address = 0” Contact Emerson Actuation Technologies Installation guide Bettis Q-Series DOC.IG.BQC40.1 Rev. 3 5.3 Check operation 5.3.1 Default (single) pilot valve operation 1. For function test, the unit must be connected to an ASI master device or an ASI gateway. 2. Connect pressure according chapter 3 and the ASI bus signal according chapter 4. 3. For sending the “Open” or “Closed” command, check the applicable sections of the documentation supplied with the ASI master device or the ASI gateway. 4. Send an “Open” command to the Solenoid 1 DO (Data bit D1) of the ASI module. 5. Actuator moves to “Open” position. 6. Send an “Close” command to the Solenoid 1 DO (Data bit D1) of the ASI module. 7. Actuator moves to “Closed” position. 8. Mount the Control Module cover to the housing (see figure 3.1). May 2018 5.3.2 Dual pilot valve (Fail in Last Position) operatation Important: The QC40 ASI Control module with Dual Pilot valves has only the Fail-in-Last-Position function when the module is mouted to a double acting actuator. 1. For function test, the unit must be connected to an ASI master device or an ASI gateway. 2. Connect pressure according chapter 3 and the ASI bus signal according chapter 4. 3. For sending the “Open” or “Closed” command, check the applicable sections of the documentation supplied with the ASI master device or the ASI gateway. 4. Send an “Open” command to the Solenoid 1 DO (Data bit D1) of the ASI module while “Close” command to Solenoid 2 DO (Data bit D0). 5. Actuator moves to “Open” position. 6. Remove the ASI wiring from the module terminals. 7. The double acting actuator should not rotate. 8. Re-connect the ASI bus signal according chapter 4. 9. Send an “Open” command to the Solenoid 2 DO (Data bit D0) of the ASI module while “Close” command to Solenoid 1DO (Data bit D1). 10.Actuator moves to “Closed” position. 11.Remove the ASI wiring from the module terminals. 12.The double acting actuator should not rotate. 13.Mount the Control Module cover to the housing (see figure 3.1). 11 Bettis Q-Series Installation guide May 2018 6 Trouble shooting 6.1 The “Open” and “Closed” position feedback signals are reversed from the actual valve positions. 1 Check if the actuator is correctly mounted to the valve. Before mounting the actuator on the valve, the actuator and the valve should have the same “open” or ‘closed” position (see Installation & Operation Manual Bettis Q-Series Valve Actuator DOC.IOM.BQ.E). 2 Some valves may be operated in such a way that they are: - “Open” after a clock wise rotation and - “Closed” after a clock wise rotation. 3 Please see § 5.1 for setting the “Open” and “Closed” position feedback signals 6.2 The actuator does not give (good) position feedback signals. 1 Check if the actuator is correctly mounted to the valve. 2 Re-adjust the limit switch setting as per chapter § 5.1 6.3 Factory setting of the switch points. IMPORTANT The procedure below assumes: - That the actuator / valve assembly is closed after a clock wise rotation (see also § 5.1). - The control module is pneumatically and electrically connected according chapter 3 and 4. This procedure sets the switch point settings of the switches, back to the factory settings (±15° before each end of stroke), assuming a mechanical stroke of 90°±0.5° of the actuator. To set and detect the Open or Closed switch points, the QC40 AS-I module has two LED’s that light up if the Open or Closed position limit switch is activated. 12 DOC.IG.BQC40.1 Rev. 3 Procedure (see fig 5.3): 1. Loosen the screw (1) of the shield (2) and turn the shield down. Closed Position: 2. Send an “Close” command to the ASI module. 3. Turn top screw (3) counter clock wise maximum 20 turns, (do not force the adjustment screw) until the switch trips and the corresponding LED (5) goes out. 4. Turn top screw (3) clock wise 1 3/4 turn (do not force the adjustment screw). The “closed” position switch point is now set to factory setting. Open Position: 5. Send an “Open” command to the ASI module. 6. Turn bottom screw (4) clock wise maximum 20 turns, (do not force the adjustment screw) until the switch trips and the corresponding LED (6) goes out. 7. Turn bottom screw (4) counter clock wise 1 3/4 turn (do not force the adjustment screw) The “open” position switch point is now set to factory setting. 8. Turn the shield (2) back over the adjustment screws and fasten it with the screw (1). Important: Do not force the adjustment screws During switch point adjustment, do not force the adjustment screws when you feel an obstruction. Forcing the adjustment screws can damage the cross head of the adjustment screw. Installation guide Bettis Q-Series DOC.IG.BQC40.1 Rev. 3 7 May 2018 Maintenance 8 The Bettis Q-Series control modules are designed to operate without maintenance. For any further maintenance to the actuator see Installation & Operation Manual Bettis Q-Series Valve Actuator, DOC.IOM.BQ.E or contact your local Bettis Q-Series representative. Installation, adjustment, putting into service, use, assembly, disassembly, maintenance and repair of the control module must be done by qualified personnel. For any further maintenance to the control module see Maintenance Manual, DOC.MM.QC40.E or contact your local Bettis Q-Series representative. Installation, adjustment, putting into service, use, assembly, disassembly, maintenance and repair of the control module must be done by the qualified personnel. ! WARNING • Substitution of components may impair suitability of the equipment Optional Controls 8.1 Manual Control options (see figure 8.1) For commissioning, emergency or maintenance purposes, the Bettis Q-Series can be supplied with one or two Manual Control options. These can operate the spool valve(s) inside the module and as such operate the actuator, when there is air pressure available, but no control signal or power supply. 8.1.1 Mounting Manual Control 1 To add a Manual Control, remove the plug(s) in front of the module and turn in the Manual Control. - For normal operation the module should be fitted with one Manual Control. - For Double Acting with a Fail-in-Last-Position function, two Manual Control can be fitted. 8.1.2 Manual Control operation 1 The Manual Control has a “Push & Lock” function: - To operate the Manual Control, use a screw driver, push to activate and release to de-activate the pilot valves. - If required turn it 45°, to lock it in position and keep the actuator in its operated state. 2 In case of a Fail in Last Position configuration with two manual controls: - The manual control on the right side (default location) will pressurize the central air chamber and cause the actuator to rotate counter clock wise. For reverse acting Bettis Q-Series actuators (Assembly code CC) the actuator will rotate clock wise. Location for 2nd Manual Control - The manual control on the left side (Location for 2nd Manual Control) will pressurize the end cap air chambers and cause the actuator to rotate clock wise. For reverse acting Bettis Q-Series actuators (Assembly code CC) the actuator will rotate counter clock wise. - In order to operate one of the manual control, be sure the opposite manual control is de-activated and unlocked. Lock 45° Unlock On Default location of Manual Control Off Fig. 8.1 Local Manual Control options 13 Bettis Q-Series Installation guide May 2018 DOC.IG.BQC40.1 Rev. 3 9 8.2 Speed control option Other documents containing information related to the Bettis Q-Series Module include: (see figure 8.2) The Bettis Q-Series can be supplied with a Speed Control option. One throttle is required for Spring Return actuators and up to two for Double Acting actuators. The speed control throttle controls the air flow in and out of an air chamber and as such limits the speed of the “Opening” and “Closing” stroke simultaneously. 8.2.1 Mounting Speed Control throttle(s): 1 Remove the plug(s) at the side of the module and turn in the throttle (1). 2 Spring Return actuators: Use the top entry only. 3 Double acting actuators: Use both bottom and top entries. - For standard actuators, the top entry will throttle the closing stroke. - For standard actuators, the bottom entry will throttle the opening stroke. - For reverse acting actuators, the opposite strokes will be throttled. 8.2.2 Adjusting Speed Control throttle(s): 1 Remove the nut cap (2). 2 Clockwise rotation of the adjustment screw reduces the speed. 3 Counter clockwise rotation of the adjustment screw increases the speed. 4 Replace the nut cap. Spring Return: Top entry only. Double Acting: Bottom and/or top entries. 2 Fig. 8.2 Speed control operation 14 Related Information 1 - 1.604.13: QC40 AS-I Control Module data sheets DOC.IOM.BQ.E: Installation Operation & Maintenance Manual. These documents are available, in multiple languages, for download go to www.emerson.com/bettis 9.1 Applied IECEx standards The following standards are applied: - For Bettis Q-Series Control Module QC40...P4... , IEC 60079-0 Ed. 6.0 : 2011 IEC 60079-15 Ed. 4.0 : 2010 IEC 60079-31 Ed. 2.0 : 2013 9.2 RoHS Directive This product is only intended for use in large scale fixed installation excluded from the scope of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS 2). Installation guide Bettis Q-Series DOC.IG.BQC40.1 Rev. 3 May 2018 10 EU Declaration of Conformity Legal representative entity for the European Union: Emerson Process Management, Valve Automation Asveldweg 11, 7556 BR Hengelo Netherlands ROC nr 11100 Rev. 0 EU DECLARATION OF CONFORMITY Issued in accordance with the EMC Directive 2014/30/EU, Appendix 1 ATEX Directive 2014/34/EU above mentioned European Directives. Product description: Serial number: Year of Construction: Manufacturer: QC40 AS-I Control module Emerson Machinery Equipment (Shenzhen) Co. Ltd. Bao Heng Technology Industry Park Phase 2, North Hong Lang 2nd Road District 68, Bao’an District, 518101 Shenzhen, China EMC Directive 2014/30/EU Types: Applicable standards: QC40... IEC61326-1 : 2012 NAMUR Recommendations : NE21: 2004 ATEX DIRECTIVE Types: Marking: Applicable standards: QC40...P4... DEKRA 16ATEX0100 X II 3 G Ex nA IIC T4 Gc II 2 D Ex tb IIIC T80°C Db Ta = -25°C ... +60°C EN 60079-0 : 2012 + A11:2013 EN 60079-15:2010 EN 60079-31:2014 Meander 1051, 6825 MJ Arnhem, The Netherlands EN Signed: Name: Position: ____________________________ S. Ooi Vice President, Global Marketing & Pneumatic/Hydraulic SBU Emerson, Actuation Technologies Date: Place: 2016-11-25 Houston TX, U.S.A. 15 Bettis Q-Series Installation guide May 2018 DOC.IG.BQC40.1 Rev. 3 11 QC40 ASI Smart Modules Non Incendive / Non sparking 11.2 ATEX / IECEx Intended use 11.1 Product marking IECEx Hazardous or Classified Location Certificate No.: DEK 16.0061 X Non-Sparking Ex nA IIC T4 Gc Ex tb IIIC T80°C Db ATEX Hazardous or Classified Location Certificate No.: DEKRA 16ATEX0100 X Non-Sparking II 3 G Ex nA IIC T4 Gc II 2 D Ex tb IIIC T80°C Db FM 11.3 Safety instructions Hazardous or Classified Location Non Incendive - Class I, II, III, Division 2, Groups ABCDEFG, T4 - Class 1, Zone 2, Group IIC T4 CSA Hazardous or Classified Location Certificate No.: CSA 17CA70125362X Class I, Division 2, Groups A, B, C and D, T4; Class II, Division 1, Group E, F and G, T80°C; Class III, Division 1, T80°C Ex nA nC IIC T4 Gc Ex tb IIIC T80°C Db Ambient temperature: T4 @ Ta = -25°C...+60°C IP66/Nema 4X Terminals Lockable cover • The Control Module QC40..P4.. of the Bettis Q-Series pneumatic actuator is a Group II category 3G (ATEX) equipment with protection level Gc (IECEx). • The Bettis Q-Series pneumatic actuators is a Group II category 2 equipment. • Both are intended for use in areas in which explosive atmospheres caused by mixtures of air and gases, vapors, mists or by air/dusts are likely to occur. • Therefore the assembly may be used in hazardous area classified Zones 2 (Gasses) and/or 21, 22 (Dust). Type plate ! WARNING • Personal injury or property damage caused by fire or explosion may occur if the module is opened in any area which contains a potentially explosive atmosphere or has been classified as hazardous. • Do not open when module is energized. • Prevent any kind ignition during installation, adjustment, putting into service and use. • Assembly, disassembly and maintenance must be done in safe area’s without a potential explosion hazard. • Installation, adjustment, putting into service, use, assembly, disassembly and maintenance or repair, shall be carried out in accordance with the applicable code of practice by suitably-trained personnel. • Provisions must be made to prevent the rated supply voltage being exceeded by more than 40%. • Potential electrostatic charging hazard, clean only with a damp cloth - danger of propagating discharge. • The apparatus shall be installed in such a way that the risk from electrostatic discharges and propagating brush discharges caused by rapid flow of dust is avoided. Do not open when energized Fig 11.1 Product marking 16 • Precaution shall be taken to avoid danger of ignition due to electrostatic charges on the marking plate of the enclosure. Installation guide Bettis Q-Series DOC.IG.BQC40.1 Rev. 3 • Substitution of electronics cartridge, switch cartridge, pilot valve cartridge, pneumatic cartridge, enclosure and seals must be with parts from Emerson else the suitability for Division 2 will be impaired. 11.4 CSA safety instructions • The equipment may be used in zones 2 with • • • • flammable gases and vapours with apparatus groups IIA, IIB & IIC and with temperature classes T1, T2, T3, T4. The equipment may be used in zones 21 & 22 with flammable dusts, fibres and flyings in groups IIIA, IIB and IIC, with a layer autoignition temperature of not less than 75 K above the maximum surface temperature marked in the dust coding. There are no special checking or maintenance conditions other than a periodic check. With regard to explosion safety, it is not necessary to check for correct operation. If the equipment is likely to come into contact with aggressive substances, e.g. acidic liquids or gases that may attack metals or solvents that may affect polymeric materials, then it is the responsibility of the user to take suitable precautions that prevent it from being adversely affected thus ensuring that the type of protection is not compromised. May 2018 11.5 Wiring instructions QC40 Non Incendive / Non Sparking Protocol AS-Interface Spec3.0 Maximum Voltage 31.6V Minimum Current 34mA at 26.5V (pilot valves off) Nominal Current (one pilot valve 85mA at 26.5V activated) Maximum Current Consumption 125mA at 26.5V (one pilot valve application) Maximum Current Consumption 140mA at 26.5V (two pilot valves application) Protection Short circuit detection * The current restricted power supply meets NEC Class 2, as described by the National Electrical Code® (ANSI/NFPA 70 (NEC®)) Terminal connections Unclassified or Non Hazardous Location AS-I power supply Hazardous or Classified Location + 1 2 - 3 Warning * Explosion hazard. Do not disconnect equipment when a flammable or combustible atmosphere is present. * Use installation wiring connections with admitted maximum operating temperature of at least 20 ºC (68°F) higher than maximum ambient. 17 Bettis Q-Series May 2018 18 Installation guide DOC.IG.BQC40.1 Rev. 3 Installation guide DOC.IG.BQC40.1 Rev. 3 Bettis Q-Series May 2018 19 World Area Conﬁguration Centers (WACC) offer sales support, service, inventory and commissioning to our global customers. Choose the WACC or sales ofﬁce nearest you: NORTH & SOUTH AMERICA MIDDLE EAST & AFRICA 19200 Northwest Freeway Houston TX 77065 USA T +1 281 477 4100 P. O. Box 17033 Jebel Ali Free Zone Dubai T +971 4 811 8100 Av. Hollingsworth 325 Iporanga Sorocaba SP 18087-105 Brazil T +55 15 3413 8888 P. O. Box 10305 Jubail 31961 Saudi Arabia T +966 3 340 8650 ASIA PACIFIC No. 9 Gul Road #01-02 Singapore 629361 T +65 6777 8211 24 Angus Crescent Longmeadow Business Estate East P.O. Box 6908 Greenstone 1616 Modderfontein Extension 5 South Africa T +27 11 451 3700 www.emerson.com/bettis ©2018 Emerson. All rights reserved. No. 1 Lai Yuan Road Wuqing Development Area Tianjin 301700 P. R. China T +86 22 8212 3300 EUROPE Holland Fasor 6 Székesfehérvár 8000 Hungary T +36 22 53 09 50 Strada Biffi 165 29017 Fiorenzuola d’Arda (PC) Italy T +39 0523 944 411 For complete list of sales and manufacturing sites, please visit www.emerson.com/actuationtechnologieslocations or contact us at [email protected] The Emerson logo is a trademark and service mark of Emerson Electric Co. BettisTM is a mark of one of the Emerson family of companies. All other marks are property of their respective owners. The contents of this publication are presented for information purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by our terms and conditions, which are available on request. We reserve the right to modify or improve the designs or specifications of our products at any time without notice.