Lorus Ladies' Lumibrite Dial Strap Watch Instruction Manual

12-2011
NREAQ1
■ HOW TO USE NON-CALENDAR MODEL
Normal position
First click
Pull the crown OUT to the FIRST click and set the
time. Then push the crown IN.
Note: When you set the time, first set the minute
hand to a properly advanced time, then
return the minute hand to the correct time
by turning it COUNTERCLOCKWISE.
■ H O W T O U S E D AY / D AT E M O D E L
The day of the week can be displayed
bilingually (English/another language) and you
can select either.
1. How to set the day and date
Pull out the
crown to the first
click position.
(The crown of
this watch can
be pulled out to
the second click
position.)
Turn the crown
and set the
previous day
and date. (The
day and date
can be selected
alternatively
and displayed in
English or the
other language.)
(For Cal. PC33,
turn clockwise to
set the date
only.)
Pull out the
crown to the
second click
position and
set the present
day and date
by turning the
minute hand.
Day setting for Cal. PC33
At the second click position,turn the hands
clockwise and counterclockwise repeatedly
between 11:15 pm and 3:45 am to select the
desired day and language.
Note: Do not attempt to set the day and date
between the times of 9:00 pm and 4:00 am
as this may cause the day and date
displays to change out of sequence.
2. How to set the time
Pull out the
crown to the
second click
position and the
second hand
stops. The
second hand
should
be
stopped on 12
o’clock position.
•
•
Turn the crown
and set the
desired time.
Push the crown
in to the normal
position in
accordance
with a time
signal.
Be sure to check that the AM/PM is correctly
set. (The day and date are designed to
change once every 24 hours.)
To adjust the correct time for a quartz watch,
it is necessary to advance the minute hand
4 or 5 minutes ahead of the correct time and
then turn it counterclockwise to set the
designated time.
■ L U M I B R I T E WAT C H
✼ If your watch is a LORUS LUMIBRITE watch, it
has following features.
LORUS LUMIBRITE watches absorb and store light
energy from natural and artificial light sources
and emit light in the dark. They are made of
environmentally friendly material, and therefore,
are harmless to human beings and the
environment.
•
•
With a full charge, LORUS LUMIBRITE watches
glow in the dark hours longer than conventional luminous watches of this type. If exposed to a light of more than 500 lux (i.e.,
the brightness of a typical office) for approximately 10 minutes, or direct sunlight for 2
minutes, they will glow for hours.
Since LORUS LUMIBRITE watches emit the light
they store, the brightness will decrease
gradually over time. The length of time they
will glow may also differ slightly depending
on such factors as the brightness of and
distance from the light source used to charge
the watch.
Page 1
11.11.9, 11:34 AM
Adobe
■ B AT T E RY C H A N G E
As the battery is inserted at the factory to check
the function and performance of the watch, its
actual life once in your possession may be less
than the specified period.
Be sure to replace the battery to prevent any
possible malfunction as soon as it runs down. To
replace the battery, we recommend taking the
watch to a local watch retailer.
■ C A R E O F Y O U R L O R U S WAT C H
• BATTERY
CAUTION
Do not expose the old battery to fire
or recharge it. Keep it at a place
beyond the reach of children. If a
child swallows it, consult a doctor
immediately.
• WATER RESISTANT
Condition Accidental
contact Swimming
of use
with water, and taking
such as
a shower
Indication
splashes
on the dial/
and rain
Skin
diving
Scuba
diving
case back
No
Indication
WATER
RESISTANT
WATER
RESISTANT*
(50M/5 BAR)
WATER
RESISTANT*
BAR
(
( 100M/10
or above
*
•
•
NO
NO
NO
NO
YES
NO
NO
NO
YES
YES
NO
NO
YES
YES
YES
NO
If your watch is 200 M/20 BAR, 100 M/10 BAR
or 50 M/5 BAR water resistant, it is so
indicated on the dial/case back.
Do not press the buttons or turn the crown
when the watch is wet.
If the watch is exposed to salt water, rinse it
in fresh water and then wipe it thoroughly
dry.
Caution:
Leather straps are not water resistant except so
indicated, even if the watch head is water
resistant.
• ALLERGIC REACTION
Because the case and band touch the skin
directly, it is important to clean them regularly.
If not, shirt sleeves may be stained and those
with delicate skin may develop a rash. Please
wear the watch with some play to avoid any
possible allergic reaction. If you develop a rash
on your wrist, stop wearing and consult a
physician.
• MAGNETISM
Your watch will be adversely affected by strong
magnetism. Keep it away from close contact
with magnetic objects.
• SHOCKS AND VIBRATIONS
Your watch may be worn for normal sports
activities, but be careful not to drop it or hit it
on hard surfaces.
• TEMPERATURE
Your watch is preadjusted so that constant
accuracy may be insured at normal
temperature.
■ S E RV I C E
When your LORUS watch requires repair or
sevicing, please see the enclosed WARRANTY/
GUARANTEE.
■ HOW TO ADJUST BAND LENGTH
Sliding clasp band
1. P r y u p t h e a d j u s t i n g f l a p w i t h a s m a l l
screwdriver or something with a sharpened
tip.
2. Slide the clasp to adjust it to a desired size.
3. The grooves on the Back side of the bracelet
should fit into the convex portion on the
clasp, then, close the adjust flap.
● Wrong method
If you do this way, the adjusting flap may be
destroyed.
Printed in China
Page 2
11.11.9, 11:34 AM
Adobe