Motorola i465 Nextel Guide 97 Pages
advertisement
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party Name: Motorola, Inc.
Address: 8000 West Sunrise Boulevard
Plantation, FL 33322 USA
Phone Number: 1 (800) 453-0920
Hereby declares that the product:
Product Name: i465
Model Number: H98XAH6JR7AN
FCC-ID: IHDT56KB1
Conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section
15.109(a)
FCC Notice to Users
The following statement applies to all products that have received FCC approval. Applicable products bear the FCC logo, and/or an FCC ID in the format FCC-ID: IHDT56KB1 on the product label.
Motorola has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. See 47 CFR Sec. 15.21.
Class B Digital Device
As a personal computer peripheral, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See 47 CFR Sec. 15.19(3).
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Motorola, Inc.
Consumer Advocacy Office
600 N US Hwy 45
Libertyville, IL 60048 www.hellomoto.com
Note: Do not ship your phone to the above address. If you need to return your phone for repairs, replacement, or warranty service, please contact the Motorola Customer Support Center at:
1-800-453-0920 (United States)
1-877-483-2840 (TTY/TDD United States for hearing impaired)
Certain mobile phone features are dependent on the capabilities and settings of your service provider’s network. Additionally, certain features may not be activated by your service provider, and/or the provider's network settings may limit the feature’s functionality. Always contact your service provider about feature availability and functionality. All features, functionality, and other product specifications, as well as the information contained in this user's guide are based upon the latest available information and are believed to be accurate at the time of printing. Motorola reserves the right to change or modify any information or specifications without notice or obligation.
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. All other product or service names are the property of their respective owners. Java and all other
Java-based marks are trademarks or registered trademarks of Sun
Microsystems, Inc. in the U.S. and other countries.
© Motorola, Inc., 2009.
Manual Number: NNTN7551A
HELLOMOTO
Introducing your new Motorola wireless phone. Here’s a quick anatomy lesson.
Volume Keys
PTT Button
Audio Jack
Micro USB
Connector
Connects charger and accessories.
Messaging Key
Web Key
Camera Key
Speaker
On/Off Key
Left Soft Key
Perform function in lower left display.
Menu Key
From home screen, open main menu.
Talk Key
Make & answer calls.
4-Way Navigation
Key
Right Soft Key
Perform function in lower right display.
End/Power Key
End calls, exit menu system, turns phone on/off.
OK Key
In menus & lists, press to select highlighted option.
1
check it out turn it on & off
To turn on your phone, press and hold .
for a few seconds or until the display turns on. If prompted, enter your four-digit unlock code.
Voicemail LED
Text Message LED
Bluetooth LED
1
Press and hold the
Power Key for a few seconds, or until the screen lights up, to turn on your phone.
2
Custo m izable r key that can be used to open the
Sett i n g s screen.
2
3
Press the Navigation key u p , down, left or r ig ht to highlight a m enu feature.
4
Press the r key to select.
Note: If you press the .
for more than four seconds, the handset will power “On” in
Transmitters Off
mode. See “transmitters” on page 33.
To turn off your phone, press and hold .
for two seconds.
contents
check it out . . . . . . . . . . . 2 turn it on & off . . . . . . . 2
menu map. . . . . . . . . . . . 6
use and care . . . . . . . . . . 8
essentials . . . . . . . . . . . . 9 about this guide . . . . . . 9
SIM card . . . . . . . . . . . 10 battery . . . . . . . . . . . . 10
enable security . . . . . . 14 make a phone call. . . . 14 answer a phone call . . 14
advanced calling . . . . . 15 make a push to talk call . . . . . . . . . . . . . . . 15
answer a push to talk call . . . . . . . . . . . . . . . 16
store a phone number or PTT ID . . . . . . . . . . 17
messaging . . . . . . . . . 19
inbox. . . . . . . . . . . . . . 20
outbox . . . . . . . . . . . . 23
sent items . . . . . . . . . 24 customize messaging. 24
using your handset as a modem . . . . . . . . . . 28
basics. . . . . . . . . . . . . . . 29 display . . . . . . . . . . . . 29
main menu . . . . . . . . . 30 text entry . . . . . . . . . . 30
volume . . . . . . . . . . . . 32
navigation key. . . . . . . 33 handsfree speaker . . . 33 transmitters . . . . . . . . 33
use GPS with map software . . . . . . . . . . . 34 features for the hearing impaired. . . . . 34
TTY . . . . . . . . . . . . . . . 35
main attractions . . . . . . 37 media center . . . . . . . 37
video player . . . . . . . . 38 camera . . . . . . . . . . . . 38
PTX features . . . . . . . . 41
PTT features . . . . . . . . 49
. . . . . . . . . 50
call features. . . . . . . . . . 53 turn off a call alert . . . . 53
contents 3
recent calls . . . . . . . . . 53
voice names . . . . . . . . 55
emergency calls . . . . . 56 international calls. . . . . 56
speed dial . . . . . . . . . . 57 voicemail . . . . . . . . . . . 57
talkgroup calls . . . . . . . 58
LINCaround . . . . . . . . . . 60
LINCaround . . . . . . . . . 61 exiting LINCaround . . . 61 channels and codes . . . 61
private LINCaround calls . . . . . . . . . . . . . . . 64
making emergency calls while in
setup options. . . . . . . . 66
customize. . . . . . . . . . . . 68 ring tones . . . . . . . . . . 68
backlight . . . . . . . . . . . 69
LED indicators . . . . . . . 69
wallpaper . . . . . . . . . . . 70 datebook . . . . . . . . . . . 70
hide or show location information . . . . . . . . . 72
Legal and Safety . . . . . . 7
4
Information . . . . . . . . . 74
Precautions . . . . . . . . . 75
Compatibility . . . . . . . . 75
Recycling . . . . . . . . . . . 77
4 contents
Assurances . . . . . . . . . 80
Safety . . . . . . . . . . . . . 80
Rate . . . . . . . . . . . . . . . 81
Calls. . . . . . . . . . . . . . . 82
Canada. . . . . . . . . . . . . 83
Organization . . . . . . . . 88
Recyclable . . . . . . . . . . 88
Label. . . . . . . . . . . . . . 88
Information . . . . . . . . . 89
Notice. . . . . . . . . . . . . 89
Security . . . . . . . . . . . 89
Driving . . . . . . . . . . . . 90
index . . . . . . . . . . . . . . . 92
contents 5
6 main menu u
Settings
• (see next page)
Q
Downloads Store
1
Mobile Web
L Java Apps
• Buy More
• Java System
B
Recent Calls
N
PTT Features
• PTT List
• Send Message
• Send Picture
• Send Event
• Send My Info
• Send Contact
• Configure c
Bluetooth
• Hands Free
• Link to Devices
• Device History
• Setup
• Find Me c
GPS
• Position
• Privacy
• Interface
D
Datebook
menu map
J
My Info
• My Name
• Line 1
• Line 2
• PTT ID
• Group ID
• Carrier IP
• IP1 Address
• IP2 Address
0
VoiceRecord p
Call Alert t
Ring Tones
• Buy Ring Tones
• Vibrate All: On/Off
• Ringer
• Vibrate
• Silent o
Profiles
M
Call Timers
• Last Call
• Phone Reset
• Phone Lifetime
• Prvt/Grp Reset
• Prvt/Grp Life
• Kbytes Reset l
Memo
K
Shortcuts
• [New Entry]
• 1)
• 2)Bluetooth
• 3)Ring Tones
• 4)Contacts
• 5)Mobile Web
• 6)Java Apps
• 7)Settings
• 8)Profiles
• 9)Call Forward
P
Call Forward
E
Messages
• [Create Message]
• Voice Mail
• Inbox
• Drafts
• Outbox
• Net Alert
• Fax Mail
• Sent Items
L
Contacts j
Media Center
H
Camera
P
LINCaround
L
PTT List
This is the standard Main Menu layout. Your phone’s menu may be a little different.
settings menu
Display/Info
• Wallpaper
• Text Size
• Theme
• Home Icons
• Backlight
• Clock
• Menu View
• Large Dialing
• Language
Phone Calls
• Set Line
• Any Key Ans
• Auto Redial
• Call Waiting
• Auto Ans
• Minute Beep
• Call Duration
• TTY
• Hearing Aid
• Notifications
• DTMF Dialing
• Prepend
Push To Talk
• Tkgrp Silent
• Tkgrp Area
• One Touch PTT
• Alert Type
• PTT Quick Notes
• On/Off Features
• Store Rcvd Info
• PTT Backlight
Personalize
• Menu Options
• Up Key
• Down Key
• Left Key
• Right Key
• Center Key
• Left Sftkey
• Right Sftkey
• Power Up
Volume
• Line 1
• Line 2
• Messages
• Earpiece
• Speaker
• Keypad
• Java Earpiece
• Java Spkr
• Data
Security
• Phone Lock
• Keypad Lock
• SIM PIN
• GPS PIN
• Change Passwds
Advanced
• Alert Timeout
• Headset/Spkr
• Connectivity
• Reset Defaults
• Return to Home
• Transmitters
• Phone Only
• Baud Rate
7
8
use and care
Use and Care
To care for your Motorola phone, please keep it away from: liquids of any kind
Don’t expose your phone to water, rain, extreme humidity, sweat, or other moisture. If it does get wet, don’t try to accelerate drying with the use of an oven or dryer, as this may damage the phone.
extreme heat or cold
Avoid temperatures below 0°C/32°F or above 45°C/113°F .
dust and dirt
Don’t expose your phone to dust, dirt, sand, food, or other inappropriate materials.
cleaning solutions
To clean your phone, use only a dry soft cloth. Don’t use alcohol or other cleaning solutions.
microwaves
Don’t try to dry your phone in a microwave oven.
the ground
Don’t drop your phone.
essentials
Caution: Before using the phone for the first time, read the Important Safety and Legal information included in the gray-edged pages at the back of this guide.
about this guide
This guide shows how to locate a menu feature as follows:
Find it: / > u > Phone Calls
This means that, from the home screen:
1 Press the menu key / and then press the Settings menu option u .
2 Press the navigation keys ; to scroll to
Phone Calls , and press the center key r to select it.
symbols
This means a feature is network or subscription dependent and may not be available in all areas, or might not be offered by your service provider. Contact customer service for more information.
This means a feature requires an optional accessory.
essentials 9
SIM card
insert the SIM card
Warning: To avoid loss or damage, do not remove your SIM card from your phone unless absolutely necessary.
battery
Battery Use & Battery Safety
• Motorola recommends you always use Motorola-branded batteries and chargers.
The warranty does not cover damage caused by non-Motorola batteries and/or chargers.
Caution: Use of an unqualified battery or charger may present a risk of fire, explosion, leakage, or other hazard.
Improper battery use, or use of a damaged battery, may result in a fire, explosion, or other hazard.
• Battery usage by children should be supervised.
• Important : Motorola mobile devices are designed to work best with qualified batteries. If you see a message on your display such as Invalid
10 essentials
Battery or Unable to Charge , take the following steps:
• Remove the battery and inspect it to confirm it bears a Motorola “Original
Equipment” hologram;
• If there is no hologram, the battery is not a qualified battery;
• If there is a hologram, replace the battery and retry charging it;
• If the message remains, contact a
Motorola Authorized Service Center.
• New batteries or batteries stored for a long time may take more time to charge.
• Charging precautions: When charging your battery, keep it near room temperature. Never expose batteries to temperatures below 0°C (32°F) or above 45°C (113°F) when charging.
Always take your mobile device with you when you leave your vehicle.
• When storing your battery, keep it in a cool, dry place.
• It is normal over time for battery life to decrease, and for the battery to exhibit shorter runtime between charges or require more frequent or longer charging times.
• Avoid damage to battery and mobile device.
Do not disassemble, open, crush, bend, deform, puncture, shred, or submerge the battery or mobile device. Avoid dropping the battery or mobile device, especially on a hard surface. If your battery or mobile device has been subjected to such damage, take it to a Motorola
Authorized Service Center before using. Do not attempt to dry it with an essentials 11
appliance or heat source, such as a hair dryer or microwave oven.
• Use care when handling a charged battery: Particularly when placing it inside a pocket, purse, or other container with metal objects. Contact with metal objects (e.g., jewelry, keys, beaded chains) could complete an electrical circuit (short circuit), causing the battery to become very hot, which could cause damage or injury.
Promptly dispose of used batteries in accordance with local regulations.
Contact your local recycling center for proper battery disposal.
Warning: Never dispose of batteries in a fire because they may explode.
battery installation
1 Pull out the connector cover. Slide the battery door downwards until it is released from the phone.
12 essentials
2 Remove the battery door.
3 Push the battery down until it snaps in place.
battery charging
New batteries are not fully charged. charge using the charger
1 Pull out the connector cover, and insert the charger into the micro USB connector on your phone as shown.
4 Replace the battery door and slide it up while pressing gently until you hear a click.
charge from your computer
You can partially charge your phone’s battery by connecting a Motorola-approved
USB cable from your phone’s micro-USB port to a high power USB connector on a essentials 13
computer (not a low-power one, such as the
USB connector on your keyboard or bus-powered USB hub). Typically, USB high-power connectors are located directly on your computer.
enable security
You must enable security the first time you power on you phone or within 10 days of first activation of your phone.
1 Press K under Ok .
2 You are prompted to enable security.
Press K under Yes . A series of screens followed by the default home page displays.
3 Press .
to return to the home screen.
make a phone call
Enter a phone number and press , or use a
voice command. See “place a call using a voice name” on page 55.
To hang up press .
.
answer a phone call
1 If you want to answer the call on speaker phone, press the speaker key ) .
2 If you want to answer the call using the handset, press , . To hang up press .
.
3 If you are using a Bluetooth headset, press the answer key on your headset. To hang up press the key again.
1 4 essentials
advanced calling
feature call waiting To accept the second call and put the active call on hold press K under Yes .
To accept the second call and end the active call press
.
.
3-way call Make or receive a phone call and press / > 3 Way . Enter the second phone number, press , and K under Join .
You cannot make and other calls during a three-way call, even if one party hangs up.
any key answer
To answer phone calls by pressing any key on the keypad press / > u >
Phone Calls > Any Key Ans > On .
make a push to talk call
Your PTT ID is the number at which you receive one-to-one Push to Talk calls.
Talkgroup numbers are numbers through which you receive one-to-many group calls.
to make a push to talk call
1 Enter the PTT ID you want to call.
2 Press and hold the PTT button. Begin talking after your phone emits a chirping sound.
3 Release the PTT button to listen.
To end the call press .
.
Note: A Push to Talk call ends automatically if there is no activity on the call for a few seconds.
essentials 15
send call alerts
Sending a call alert discretely lets the recipient know that you want to talk to him or her on a Push to Talk call.
When you send a call alert, the recipient’s handset displays your name and emits a series of beeps or vibrations.
to send a call alert
1 Enter the PTT ID you want to call as you would when making a Push to Talk call.
2 Press K under Alert .
When the message Ready To Alert appears on the display, press the PTT button until the message Alert Successful appears.
answer a push to talk call
1 When your phone emits a chirping sound or vibrates to indicate you are receiving a
Push to Talk call, wait for the caller to finish speaking.
2 Press and hold the PTT button and begin talking after your phone emits a chirping sound.
3 Release the PTT button to listen.
To end the call press .
.
16 essentials
answer a call alert
When you receive a call alert, you must do one of the following: option
Answer: Begin a Push to Talk call with the sender.
Queue: Store the call alert to the call alert queue.
Clear: Dismiss and delete the call alert.
You cannot receive phone calls or Push to Talk calls until you do.
to answer a call alert
1 Press the PTT button to start a Push to
Talk call with the sender.
or
2 Queue the call alert by pressing K under
Queue .
or
3 Clear the call alert by pressing K under
Clear .
store a phone number or PTT ID
You can store a phone number or PTT ID in
Contacts :
Find it: / > L > [New Contact]
1 Enter a name for the new entry. Each entry’s name can contain 20 characters.
2 Select a specific Ring Tone .
3 Select a type for the entry ( Mobile , PTT ID ,
Work1 , Work2 , Home , Email , Fax , Pager , Talkgroup ,
PTT List , IP or Other ). To store a PTT ID choose PTT ID .
4 Enter the number for the entry and press
K under Save when done.
essentials 17
contacts
feature edit/delete contact entry
Press
K
under Contcs .
Select a contact and press
/ > Edit . Change the desired content and press r . Press
K
under Save .
set ringer ID Press K under Contacts.
Select a contact and press
/ > Edit . Select Ringer and choose your desired ring tone. Press K under Done .
call a stored phone number or PTT ID
Find it: / > L or, press the K under Contcs .
1 Scroll to the Contacts entry.
2 If the Contacts entry contains more than one number, scroll left or right until the type of the number you want to call is displayed ( Mobile , PTT ID , Work1 , Work2 , Home , etc.).
3 If you chose a phone number, press , to call the entry, or if you chose a PTT ID,
Talkgroup ID, or PTT List, press and hold the PTT button to call the number.
your phone number and
PTT ID
Follow the directions below to locate your phone number and PTT ID.
Find it: / > My Info
Tip: Want to see your phone number or PTT
ID while you’re on a call? Press / > My Info .
18 essentials
messaging
Your phone sends text messages using
Mobile Originated Short Messaging Services
(MOSMS) and receives text messages from other phones that are using MOSMS.
Note: The messaging menus may look slightly different depending on the messaging setup of your phone.
create and send messages
1 From the home screen press
K
under
Mesgs > [Create Message] or press L located at the top right side of the display.
2 Enter the phone number of the person you want to send the message to and press r or press
K
under Browse . Select
Contacts or Recent Calls to find the number you want and press K under Done .
3 Select Mesg : and enter the text of the message or to use a quick note press K under QNotes and scroll to the quick note you want then press r .
4 If you want to send the message, press
K under Send or to delete the message without sending it, press K under Cancel .
quick notes
When you are filling in the Message field, you can add ready-made words or short phrases called Quick Notes. After you add these words or phrases, you can edit them as you would any other text.
1 While you are creating a message, scroll to or select Message .
2 Press
K
under QNotes .
3 Select the quick note you want to insert into the message then press r .
4 Press K under Send .
essentials 19
use drafts
When you save a message as a draft, it is saved in the drafts folder.
Find it: Press / > E > Drafts .
1 Select the draft you want to edit.
2 To edit the fields you want to change, follow step 2 through step 4 in “create and send messages” above.
delete a draft
When you send a draft, it is removed from the
Drafts folder.
1 To delete a message in the Drafts folder without sending it, scroll to the message you want to delete and press
K
under
Delete .
2 Press K under Yes to confirm.
inbox
Find it: Press / > E > Inbox .
receive a message
1 To view the message press K under Read .
2 To dismiss the message notification press
K
under Exit .
While reading a text and numeric message that contains a phone number, you can press
, to call that number.
Note: The Text Message LED( 9 ) will appear when you have unread text messages.
threaded inbox
The threaded Inbox allows you to organize your messages by sender.
1 From the Inbox, highlight a message.
20 essentials
2 Press / > Threading , and select from None or Sender .
read from the message center
1 From the home screen press K under
Mesgs > Inbox .
2 Select the message you want to read.
3 To reply to the message, press
K
under
Reply .
delete unread messages
1 Scroll to the message you want to delete.
2 Press K under Delete and K under Yes to confirm.
forward a message
1 Press / > Forward .
2 Create and send your message.
Embedded objects and attachments are included when you forward a message.
lock and unlock messages
Locked messages cannot be deleted until you unlock them.
1 View the message you want to lock or unlock.
2 Press / > Lock Message or Unlock Message .
call a number in a message
If a message you receive contains a phone number, PTT ID, or Talkgroup ID in the From field, the To field, or the body of the message, you can call or send a call alert to that number.
send a call alert
1 View the message.
essentials 21
2 Highlight the PTT ID or Talkgroup ID you want to alert.
3 Press / > Alert .
4 Push the PTT button.
make a talkgroup call
1 View the message.
2 Press / .
3 Highlight the Talkgroup ID you want to call.
4 Select Talkgroup .
5 Push the PTT button.
store message information to contacts
If a message you receive contains a phone number, PTT ID, Talkgroup ID, or an email address in the From field, the To field, or the
22 essentials body of the message, you can store this information to Contacts .
1 View the message.
2 Highlight the number or email address you want to save.
3 Press / > Save Number or Save Email .
4 To store the number or email address as a new entry, select [New Contact] .
To store the number or email address to an existing entry, select the entry.
5 With the Contacts type field highlighted, press ; left or right to display the
Contacts type you want to assign the number or email address.
6 Press K under Save .
reply to a message
To reply to a message:
1 View the message you want to reply to.
2 To reply to the sender only, press K under Reply or press K under Reply All to reply to all recipients.
3 A list of short phrases appears. Select any of these phrases to add it to your messages or select [Create Reply] .
4 Edit any message fields you want to change.
5 Press K under Send .
use auto replies
If the message you are replying to was sent with auto replies, it contains a numbered list of possible replies for you to send. Press the number of the reply you want to send. The reply is sent immediately without further action.
go to a website
If a message contains one or more website
URLs, you can go to that website.
1 View the message.
2 Highlight the website URL you want to go to.
3 Press / > Go To Website.
Note: The entire URL must appear in the message to allow you to open the website.
outbox
The Outbox holds all unsent messages.
Find it: Press / > E > Outbox .
resending failed messages from the outbox
1 Highlight the message you want to resend.
essentials 23
2 Press K under Resend .
cancel an unsent message
1 Highlight the message you want to cancel.
2 Press / .
3 Press
K
under Cancel .
sent items
The Sent Items box holds sent messages.
forward items from sent items
1 Scroll to the message you want to forward.
2 Press / > Forward .
3 Make edits if you wish, select the recipient and press
K
under Send .
check delivery status
If a message was successfully sent and you set the message to confirm delivery, you can check the delivery status:
1 Scroll to the message you want to view.
2 Press / > Delivery Status .
delete sent messages
1 Scroll to the message you want to delete.
2 Press K under Delete .
3 Press K under Yes to confirm.
delete all unlocked sent messages
1 Press / > Delete All .
2 Press
K
under Yes to confirm.
customize messaging
Find it: / > E > / > Setup .
2 4 essentials
This option is available from many context-sensitive menus.
The following options become available: option
Signature: Allows you to create a signature that is automatically inserted at the end of your messages. Signatures can be edited before sending the message.
Quick Notes: Lets you create new Quick Notes and edit or delete Quick Notes you created.
Cleanup: Controls how long messages remain in the Inbox and Sent Items before being deleted.
Delivery Rpt: Allows you to be automatically notified when your message is delivered.
Memory Size: Shows a report on used and free memory in your phone.
Text Msg Setup: opens a submenu to set text messaging options.
manage memory
Your text Inbox and Sent Items hold 200 messages each. The Outbox, and Drafts folder hold up to 30 messages each. If they are full, you cannot receive messages, send messages, or save drafts until you delete some items.
To view the amount of memory available in your text inbox:
Find it: Press / > E > / > Setup >
Memory Size .
text message setup
Find it: / > E > / > Setup > Text Msg setup .
This option is available from many context-sensitive menus.
essentials 25
The following options become available: option
Srvc Cntr No: Allows you to enter a service center number.
Expire After: Allows you to set the number of days before a message expires.
cleanup options
The cleanup option controls how long messages remain in the Inbox and Sent Items before they are deleted. You set the cleanup option for the Inbox and Sent Items separately.
The clean up option deletes only read, unlocked messages and sent messages.
Find it: / > E > / > Setup > Cleanup.
1 Select Inbox or Sent Items .
2 Choose a clean up option from the following list: option
Off: Messages are never automatically deleted.
5 Messages: If you have more than 5 messages, messages are deleted in the order they were received, starting with the oldest, until 5 are left.
10 Messages: If you have more than 10 messages, messages are deleted in the order they were received, starting with the oldest, until 10 are left.
1 Day : Messages are deleted if they are older than 1 day.
3 Days: Messages are deleted if they are older than 3 days.
With these options, messages are deleted when you exit the message center after setting the option.
26 essentials
option
F-In F-Out: Messages are deleted as necessary on an FirstIn FirstOut basis.
Custom: Lets you create a clean-up option of up to 199 days for the inbox.
3 Press K under Yes to automatically delete messages now or press K under
No to delete messages later.
delete all messages
To delete all read, unlocked messages from the Inbox, all messages in the Drafts folder, or all successfully sent messages in the Outbox:
Find it: / > E .
1 Select Inbox , Drafts , Sent Items , or Outbox .
2 Press / > Delete All .
3 Press K under Yes to confirm.
delete a thread
To delete a thread from the Inbox:
1 From the Inbox, select a thread.
2 Press / > Delete Thread .
3 Press K under Yes to confirm.
message notifications
When you receive a message, your phone notifies you with text on the display, a notification tone or vibration.
You can access the message or dismiss the notification.
If you dismiss the notification, the message is not deleted. It can be accessed through the message center.
If you are not on a phone call when you receive a message, your phone sounds a notification tone every 30 seconds until you access the message or dismiss the alert.
essentials 27
If you are on a call when you receive a message, your phone may sound a notification tone during the call or after you end the call, depending on how you set your notification options.
set notification options
To control whether your phone sounds message notification tones while you are on a phone call:
Find it: / > u > Phone Calls > Notifications .
Select from the following options: option
Receive All : Tones sound during calls for all types of messages.
Msg Mail Only : Tones sound during calls for mail messages; tones for all other types of messages are held until you end calls.
option
Delay All : Tones for all types of messages are held until you end calls.
Note: Delay All is the default setting.
To set notification options during a call press
/ > Call Setup > Notifications .
using your handset as a modem
Your phone can be connected to a computer via USB for use as a modem. For more specific information on how to setup your phone for use with your computer please visit www.motorola.com/support and look under the FAQ section.
28 essentials
basics
See page 1 for a basic phone diagram.
display
The home screen shows when you turn on the phone. To dial a number from the home screen, press number keys and , .
Note: Your home screen may look different.
Time
Ready
10:05pm 10/23
Date
status indicators
Status indicators are shown at the top of the home screen:
1. 2. 3. 4.
5. 6. 7.
Time
Ready
10:05pm 10/23
Date
Left Soft
Key Label
Right Soft
Key Label
Soft key labels show the current soft key functions. For soft key locations, see page 1.
Left Soft
Key Label
Right Soft
Key Label
1 Signal Strength Indicator: Vertical bars show the strength of the network connection. You can’t make or receive calls when ~ shows.
basics 29
2 Active Phone Line: $ indicates phone line 1 is ready to make calls; ( indicates phone line 2 is ready to make calls.
3 Speaker On/Off: Sounds associated with
Push to Talk calls and group calls can be set to come through the earpiece rather than through the speaker.
4 Ringer Vibe/Off: Your phone is set to not ring.
5 Message Indicator: Shows when you receive a text message.
6 Packet Data: Your handset is ready to transfer packet data or is transferring packet data when it shows a blinking arrow.
7 Battery Charge Indicator: A fuller battery indicates a greater charge. Recharge the battery when your phone shows Low Battery .
main menu
All your phone’s features can be accessed through the main menu. You can set the main menu to appear as List View or Icon View .
Find it: / > u > Display/Info > Menu View .
text entry
Some features let you enter text.
Your phone provides convenient ways to enter words, letters, punctuation, and numbers whenever you are prompted to enter text (for example, when adding a Contacts entry or when using Text Messaging).
change the character input mode
1 When you see a screen where you can enter text, press / to change the character input mode.
30 basics
2 Select one of the following options: entry method
Alpha Press a key several times for different characters.
Word
Text
Settings
Enter words using a predictive text entering system that lets you enter a word with fewer keypresses.
Selects the desired entry languages and Word Prediction features.
word method
The Word text input method predicts the word you are typing by comparing the letters entered with dictionaries of words, and provides the most commonly-used word as you type. You may use up to two dictionaries, one for a primary language and another for a secondary language.
enter a word using “word” method character input
1 Select the Word character input method.
2 Press the corresponding keys to enter a word (for example, to enter the word Bill , press
F G H H
). (If you make a mistake, press
D
to erase a single character. Press and hold D to delete an entire entry.)
3 To accept a word and insert a space, press
I
.
To accept a word completion (such as
Billion when you entered Bill ), press the navigation key to the right. To enter Bill , press the navigation key to the left.
If next word prediction is turned on, when you hit space, you will be presented with a predicted word option. For example, if you enter Go , you will be presented with a predicted word option such as to . Press basics 31
the navigation key right to accept the predicted word.
If two or more word combinations result from the sequence of letters entered, a down arrow will be displayed. Press and hold the navigation key down to display a list of possible word choices.
When word completion is turned on, if you get a word you don’t want, you can press the navigation key up or down to see more word choices.
alpha method
To enter characters by tapping the keypad:
1 Select the Alpha method.
2 Press the corresponding keys to enter a word. For example, to enter the word Bill , press F G H H . If you make a mistake, press D to erase a single character. Press and hold D to erase an entire word.
3 To enter a symbol character, press B or A and the key for the symbol you wish to enter.
By default, the first letter of an entry is capitalized.
volume
Press the volume keys up or down to:
• turn off an incoming call alert
• change the earpiece volume during calls
• change the ringer volume from the home screen
32 basics
Tip: You can quickly set your ringer to
Vibrate All by holding the down volume key in the home screen.
navigation key
Press the navigation key up, down, left, or right to scroll to items in the display. When you highlight the desired item, press r to select it.
handsfree speaker
You can use your phone’s handsfree speaker to make calls without holding the phone to your ear.
During a call, press K under Spkr to turn the handsfree speaker On.
The handsfree speaker stays on until you press K under Spkr again.
transmitters
Consult airline staff about the use of the
Transmitters Off feature during flight. Turn off your phone whenever instructed to do so by airline staff.
Transmitters Off turns off your phone’s calling and Bluetooth features in situations where wireless phone use is prohibited, but you can use the phone’s other non-calling features when Transmitters is turned Off.
Find it: / > u > Advanced > Transmitters > Off .
basics 33
use GPS with map software
Your phone can be connected to a PC, laptop, or PDA via USB for use as a GPS receiver. For more specific information on how to setup your phone for use with your computer please visit www.motorola.com/support and look under the
FAQ section.
features for the hearing impaired
using your phone with a hearing aid
For best results use the following optimization procedures and handset setting. They generally apply as well for users with cochlear implants: optimize your handset position and orientation
While in a phone call slide your phone up and down, then left and right until best microphone coupling is obtained. You also may need to adjust your hearing aid (HA) volume setting .
If your HA has a telecoil, activate its switch, then also rotate the handset as illustrated to align the telecoils.
Note: Some automatically switched hearing aids may need an auxiliary switching magnet.
3 4 basics
If you are unsure whether your HA is telecoil equipped or needs an auxiliary magnet, please refer to your HA user guide or contact a hearing aid professional or supplier.
Approximate telecoil location is within
6-13 mm of this location.
Off - Shut off
M - Microphone
T - Telecoil
Approximate telecoil location is just above the battery.
choose your hearing aid setting
Find it: / > u > Phone Calls > Hearing Aid .
1 Set this option to Microphone . Microphone coupling is now optimized. or
2 Set this option to Telecoil . Handset meets
US federal requirements for telecoil coupling sound or set this option to Off
(factory default). This is the setting for non
HA users.
TTY
feature turn On TTY feature choose TTY mode change the
TTY baud rate
Press / > u >
Phone Calls > TTY > Use TTY > On .
Press / > u >
Phone Calls > TTY > Type .
Select from TTY , VCO or HCO .
Press / > u >
Phone Calls > TTY > Baud .
Select 45.45
or 50.00
.
basics 35
feature change TTY mode during a call
While in the TTY call, press
/ > In Call Setup > TTY > Type .
Select from TTY , VCO or HCO .
security features
feature phone lock To lock the phone press
/ > u > Security >
Phone Lock > Lock Now or
Auto Lock .
keypad lock To lock the keypad press
/ > u > Security >
Keypad Lock > Lock Now or
Auto Lock .
enable SIM
PIN
Shortcut: To lock the keypad press / > * .
Press / > u > Security >
SIM PIN > On .
36 basics feature change SIM
PIN
Press / > u > Security >
Change Passwords > SIM PIN .
Note: You can make emergency calls on a
main attractions media center
The media center lets you access pictures, audio recordings, and videos stored in your phone’s memory.
The following audio recordings can be accessed through the media center:
• Voice records
• Musical ring tones in the list of ring tones
• Audio recordings downloaded to your phone
Items in the media center can be sent in
MMS messages and with Bluetooth. See
“use drafts” on page 20 and “Bluetooth ® ” on page 50.
Pictures in the media center can be sent in
Push to Talk calls using Send via PTT. See
Audio files supported by the Media Center include:
Format
.au
.midi
.mp3
.wav
.amr
Sampling Rates/Bit Rates
8 KHz/8 kbps
8 KHz
8 KHz/8 kbps
8 KHz/64 kbps
12kbps main attractions 37
Image files supported by the Media Center include:
Format
.png
.gif
.jpg
.wbmp
Max. Image Size (in pixels)
128 x 160
128 x 160
640 x 480
128 x 160
Video files supported by the Media Center include:
Format
AVI
H.263
MPEG
Frame Rate and
Max. Image Size (in pixels)
15fps 128 x 96
15fps 128 x 96
15fps 128 x 96
video player
1 From the Media Center, scroll left or right to Media: Video.
2 Select the video you wish to view, and it will begin to play.
3 To stop the video, press the navigation key down. To play the video again, press r .
camera
You can save pictures taken with the integrated camera in your phone’s memory, and can access them through the Media
Center.
Pictures you take can be sent via Push to Talk calls and Bluetooth. You can also set them as your phone’s wallpaper.
38 main attractions
access the camera
To access the camera, press e located at the bottom right side of the display or press
/ > H .
To take pictures aim the camera lens and press K under Capture or press r .
To save the picture, press r .
To discard the picture without saving it, press
K under Discard .
From the camera viewfinder, you can press
/ to enter Menu Options .
The following options become available: option
Media Center : Opens the Media Center application.
Record Video : To record a video
Zoom : To set the camera’s zoom to 1x, 2x, or
4x.
option
Lighting : Turn on the spotlight On before taking a picture in low light conditions. You can set it up to be Normal or Low Light .
Self Timer : Delay capturing the picture for a selected number of seconds. The values are: Off (default), 10 seconds , 15 seconds , and 20 seconds .
To turn off the timer before the picture is captured, press K under Cancel .
Picture Quality : Adjust the picture quality to
Normal or Fine .
Picture Size : Set up the picture size to XL
(640x480) , L (320x240) , M (160x120) , S (128x96) , or
WP (128x160) . You can also set picture size from the viewfinder by pressing left and right.
Memory Usage : Shows the total amount of Used ,
Free , and total Capacity of the phone’s memory.
main attractions 39
option
Camera Setup : To access the camera set up screen.
access the media center
You can access the media center from the camera at any time by pressing / > Media
Center , except when you are using the Camera
Setup menu or viewing the memory screen.
The media center contains all your pictures, music files, and videos located on your phone’s memory. Press A and * or A and
# to filter your results.
customize the camera
Find it: e
> / > Camera Setup
The following options become available: option
Ask for Name : If this option is On , you are prompted to enter a name for each picture before saving. Otherwise, pictures are automatically saved with the date and a number as their names.
Shutter Sound : Sets the default sound the camera makes when it takes a picture.
Default Size : Sets the default value for the Picture
Size option.
Default Quality : Sets the default value for the quality of the picture.
4 0 main attractions
PTX features
With Push To View features, your phone can send and receive the following items through
Push to Talk calls with other phones that have this capability:
• Short text messages 1
• Pictures 1
• Datebook events
• My Info
• Contact information
• Location information 1
You can choose to send messages, pictures, events, My Info , Contacts or Location information to the PTT ID you are engaged in a Push to Talk call with, PTT IDs on the Recent Calls list, and
PTT IDs stored in Contacts .
1. Additional charges may apply.
When you make or receive a Push to Talk call, your phone automatically determines whether the phone you are engaged in a Push to Talk call with is able to receive each of these items. Your phone saves this information for as long as the PTT ID is on your Recent Calls list or is saved in your Contacts . Your phone updates the saved information each time you make or receive a call to or from that PTT ID.
Note: You cannot send PTT feature items during Talkgroup calls or PTT List calls.
send messages
The Push to Send Messages feature lets you send short text messages through
Push to Talk calls.
When you send a message, it appears on the display of the phone you are engaged in the
Push to Talk call with.
main attractions 4 1
begin a message and choose a recipient
You can begin a message during a Push to
Talk call, from the Contacts list, the Recent Calls list, or from PTT Features .
begin a message during a push to talk call
While in a Push to Talk call, press / >
Use PTT Feature > Send Message .
Note: The first time you send a message,
Messaging Fees May Apply Continue?
appears and you are prompted to respond. Press K under Yes to acknowledge the message.
begin a message from the Contacts or the Recent Calls list
1 From the Contacts or the Recent Calls list, select the entry containing the PTT ID you want to send the message to.
2 Press / > Use PTT Feature > Send Message .
4 2 main attractions begin a message from PTT Features
PTT Features lets you select the PTT ID you want to send the message to from Contacts or the
Recent Calls list.
Find it: / > N > Send Contact > Browse.
Then select Contacts or Recent Calls to see a list of entries from the Contacts or the Recent Calls list that can receive messages.
create messages
After you have begun a message and chosen a recipient, a screen appears that lets you create the text of the message you want to send. Your message may be up to 400 characters long.
You can choose from a list of ready-made words or short phrases called Quick Notes.
You can use a Quick Note as it is or edit it before you send it. Editing a Quick Note
changes the Quick Note for this message only and will not change the Quick Note on the list.
send a completed message
After you have completed your message, press the PTT button to send it.
receive messages
When you receive a message, a message notification appears on the display.
To view the message: Press K under Read .
To dismiss the message press K under
Dismiss .
reply to a message
1 View the message.
2 Press K under Reply .
3 Create the message and press the PTT button to send it.
send pictures
You can send pictures stored in the Media
Center through Push to Talk calls. The picture you send appears on the Push to Talk call recipient’s display.
If the recipient accepts the picture, their phone saves the picture. The picture then appears in that phone’s recent call list.
Note: You can create and send messages up to 100KB including attachments.
The first time you send a stored picture after turning the phone on, Picture Fees May Apply
Continue?
appears and you are prompted to respond.
Note: You cannot make or receive Push to
Talk calls while transmitting or receiving a picture.
main attractions 4 3
send a picture during a call
1 While in a Push to Talk call, press K under Picture or press / > Use PTT Feature >
Send Picture.
A list of pictures that can be included in a
Push to Talk call appears.
2 Select the picture you want to send.
3 Press the PTT button to send the picture.
4 Wait while the picture is transmitted. The
Push to Talk call is temporarily interrupted while a picture is transmitted.
5 When prompted, press the PTT button to resume the Push to Talk call.
start a call by sending a picture
from the media center
Find it: / > Media Center
1 Scroll left or right to Media: Pictures .
44 main attractions
2 Select the picture you want to send.
3 Press / > Send Via...
> Send Via PTT .
4 Select A Contact or A Recent Call
A list of contacts that have PTT IDs and are able to receive pictures appears.
5 Select the name of the person you want to send the picture to.
6 Press the PTT button to send the picture.
7 When prompted, press the PTT button to resume the Push to Talk call. from PTT Features:
Find it: / > N > Send Picture .
1 Select A Contact or A Recent Call
A list of contacts that have PTT IDs and are able to receive pictures appears.
2 Select the name of the person you want to send the picture to.
3 Select Browse Picture or Capture Picture .
4 Press the PTT button to send the picture.
5 Once picture has been sent, when prompted press the PTT button to resume the call.
receive a picture
When someone sends you a picture, your phone emits a tone or vibrates and a message appears asking if you want to accept the picture.
Pictures you receive are saved to your phone’s memory. They are accessible through the media center.
When you see a message asking if you want to accept the picture, press Yes to accept or No to decline.
clear a picture from the display
If you want to clear a picture from your phone’s display while still on a call, press
/ > Clear Screen .
send a datebook event
to send a datebook event during a push to talk call
1 While in a Push to Talk call press / >
Use PTT Feature > Send Event .
Note: If these options do not appear on the menu, the PTT ID you are engaged in a Push to Talk call with is not able to receive Datebook events.
2 If you want to create a new datebook event, press
K
under New and create the event in your datebook. If you want to chose an existing event do so.
3 If the event is a recurring event: Select
This Event Only to send only the event main attractions 4 5
selected. Select Repeat Events to send all occurrences of the event.
4 Push the PTT button to send the event.
send my info
1 While in a Push to Talk call press / >
Send via PTT > Send My Info , and push the PTT button to send.
or
2 From the home screen press / >
My Info > / > Send via PTT . Enter a PTT ID or press
K
under Browse to chose a recipient from Contacts, Recent Calls or Memo, and press r . Push the PTT button to send.
set my info sending option
You can control what portion of the information in My Info is sent and whether it is sent automatically in every call or only when you choose to send it.
4 6 main attractions
Find it: / > PTT Features > Configure >
PTT My Info > Info to Send
1 Select or remove the fields you want to send.
2 Press
K
under Done .
The information your phone sends always includes My Name , and PTT ID . You may also send
Line 1 , Line 2 , and Carrier IP , depending on your sending options. automatic sending
To control whether you send your information automatically:
Find it: / > PTT Features > Configure >
PTT My Info > Auto Send
1 Select On or Off
2 When you make a call in which your information is sent automatically, the name you entered in the My Name field of
My Info appears on the display of the
recipient’s phone, even if your name and
PTT ID are not stored in the recipient’s
Contacts.
send contact information
1 While in a Push to Talk call press / >
Use PTT Feature .
2 Select Send Contact and select the contact information you want to send.
3 Push the PTT button to send.
or
1 From the home screen press / >
PTT Features > Send Contact.
2 Enter the PTT ID number of the person you want to send the Contact information to or press K under Browse .
3 Select from Recent Calls , Contacts , or Memo .
4 Select the contact information you want to send and push the PTT button.
turn PTT features on and off
You can turn your phone’s ability to send and receive messages, pictures, and Datebook events on and off.
You cannot turn your phone’s ability to send and receive My Info and contact information on and off.
Find it: / > u > Push To Talk > On/Off Features .
1 Check or uncheck Messages, Pictures or
Events.
main attractions 4 7
one touch PTT
Find it: / > u > Push To Talk > One Touch PTT.
One Touch PTT sets your phone to do any of the following each time you press the PTT button from the home screen: option
Off : Nothing happens when you press the
PTT button from the home screen.
PTT List
: Go to PTT List. See “PTT list” on page 48.
Last Call : Call the most recent PTT ID or
Group on the recent calls list.
Assigned No.
: Call a PTT ID you assign. Enter the number using your keypad, or press
K under Search . Select Contacts , Recent Calls , or
Memo .
Note: If you are entering a Talkgroup number, enter # before the number.
4 8 main attractions option
PTT Features
: Go to PTT Features. See “PTT features” on page 49.
Send Message : Go to the first screen to send a message.
Send Picture : Go to the first screen to send
pictures. See “send pictures” on page 43.
Send Event : Go to the first screen to send a
Datebook event.
Send My Info : Go to the first screen to send My
Info. See “send my info” on page 46.
Send Contact : Go to the first screen to send a
contact. See “send contact information” on page 47.
PTT list
PTT List lets you quickly make a call, create a PTT List or make a PTT List call when accessing any PTT IDs on your phone.
To view a list of Contacts and PTT Lists with
PTT IDs in Contacts :
Find it: / > PTT List
To move between Contacts , Recent Calls , or Memo , use the ; left or right, or press
A
and * or
A and # .
To make a Push to Talk call or PTT List call:
1 Select the entries you want.
2 Press K under Done .
3 Push the PTT button.
To save your selections as a PTT List press
/ > Save PTT List . For more information about
PTT Lists, see “talkgroup calls” on page 58.
If you want to assign a name to the PTT List, enter the name.
Note: If you do not assign a name, the PTT
List is named PTT List followed by the number of members in the PTT List. For example, PTT List (8) for a PTT List with 8 members.
PTT features
PTT Features lets you quickly access PTT functions, and other Push to Talk call features, from the main menu.
Find it: / > PTT Features
1 Select PTT List , Send Message , Send Picture , Send
Event , Send My Info , Send Contact , or Configure .
After choosing what PTT item you are sending, select a contact and press the
PTT button to send.
or
2 Select Configure to configure your PTT Quick
Notes , PTT My Info , One Touch PTT , or
On/Off Features .
main attractions 4 9
Bluetooth
®
Find it: / > c
turn Bluetooth on or off
You can turn your phone’s Bluetooth feature on or off. While Bluetooth power is on, your phone can communicate with other devices.
Find it: / > c > Setup > Power
1 Select On to power Bluetooth On.
2 Select Name if you wish to assign a name to your handset.
3 Select Find Me Time to determine the amount of time in which your handset can be found by other Bluetooth devices.
You can turn off Bluetooth if you want to prolong battery life or if you enter an area where Bluetooth is prohibited.
Note: The Bluetooth status indicator on your phone’s display screen and the Bluetooth LED
( 8 ) shows your Bluetooth connection status.
make a Bluetooth connection
connect your handset with a Bluetooth headset
Find it: / > c > Hands Free > [Find Devices]
1 Follow the instructions on your Bluetooth headset to set it up to be found.
2 Once your Bluetooth headset is set to be found press r on your handset. Your phone will scan for the Bluetooth headset until it finds it. Press r when you see the name of the Bluetooth headset on your screen.
3 Your handset requires that you create a bond in order to connect with a Bluetooth
50 main attractions
headset. Press K under Yes when you are prompted to bond with the headset.
4 Enter the Bluetooth pass key.
Some Bluetooth devices ship with
Bluetooth PINs. Please refer to your
Bluetooth device’s user guide to locate this information.
If a device ships without a Bluetooth PIN, then you can enter any PIN for that device. To establish a connection to that device, enter the same PIN for both your phone and the device. For example, if you enter 1234 as the device’s PIN, then enter
1234 as your phone’s PIN.
5 Press
K
under Ok .
This handset offers the Bluetooth auto pair feature with auto pair compatible Motorola devices. When bonded via Bluetooth with a certain device, the pin will not be required.
connect your handset with another
Bluetooth device
Find it: / > c > Link To Devices
1 Select the device you want from the list of found devices on your screen.
2 Create a bond if you are prompted to do so.
If you have previously connected to a device, the device will be stored on your phone so you can connect with it easily.
use Bluetooth during a call
You can connect with available Bluetooth devices during a call.
1 While in a call, press / > Use Bluetooth .
2 Select the audio device you want to connect to from the list of Hands Free Devices .
If the Audio Devices list contains only one device, your phone will try to connect to it.
main attractions 51
send information via Bluetooth
Your handset can transfer Contacts entries,
Datebook events, audio files, pictures and videos to another Bluetooth device.
The receiving device must be within 32 feet
(10 meters) of your phone in order to connect.
Note: Files sent or received may be up to 1 MB, depending on your service provider.
sending information
1 From within Contacts, datebook, or Media
Center, select the Contacts entry,
Datebook event, audio file, video, or picture you want to send.
2 Press / > Send Via...
> Bluetooth .
3 Select the device you want to transfer the contact information to, or search for the device by selecting [Find Devices] .
4 If prompted, bond with the device.
52 main attractions
Your phone connects with the devices and transfers the information.
call features turn off a call alert
You can press the volume keys to turn off a call alert before answering the call.
recent calls
The recent calls list contains information associated with calls you have made and received and call alerts you have received.
When you send or receive Push to Talk calls, the recent call list contains the following PTX items with those calls:
• contact information received
• My Info received
• short text messages received
• pictures sent or received
• Datebook events received
The recent calls list displays up to 20 of the most recent calls and call alerts.
1 Press / > Recent Calls .
2 Scroll through the list.
3 To view more details of the item press r .
store an item to contacts from recent calls
Phone calls, Push to Talk calls, My Info,
Contacts or Location entries received from other phones can be stored to the Contacts list from the Recent Calls list.
call features 53
Find it: / > Recent Calls .
1 Scroll to or select the item you want to store.
2 Press K under Save to store the information as a new entry in the
Contacts list.
or
3 Select an existing contact and update the information.
4 Press K under Done to save your changes.
redial
To redial your last outgoing call, press and hold , or push the PTT button if it was a
Push to Talk call.
caller ID
Caller ID allows people to identify a caller before answering the phone by displaying the number of the incoming call. If you do not want your number displayed when you make a call, just follow these easy steps.
To block your phone number from being displayed for a specific outgoing call:
1 Press * 6 7 .
2 Enter the number you want to call.
3 Press , .
To permanently block your number, call your customer service provider.
call forward
Call forwarding sends calls to the phone numbers you specify. You can forward all calls to one number or forward missed calls to
5 4 call features
different numbers depending on the reason you missed the call. You can forward phone lines 1 and 2 independently.
Find it: / > Call Forward .
1 To forward all calls select All Calls and select
To to enter the phone number you want all your calls forwarded to.
or
2 You can specify a forwarding number for each type of missed call by selecting
Detailed and choosing the following options:
If Busy : When your handset is on a call or transferring data.
If No Answer : When you do not answer on the first 4 rings.
If Unreachable : When your handset is out of coverage or powered off.
voice names
You can place calls by speaking commands to your phone if you have previously assigned a voice name to your contacts.
assign voice names to contacts
1 Press K under Contcs and select
[New Contact] .
2 Assign a name, phone number and select
[Options] .
3 Select Voice Name and follow the prompt to record the voice name.
4 Press K under Back and K under Save .
place a call using a voice name
1 Press the speaker key ) until you are prompted to say the voice name.
The handset will automatically place the call.
call features 55
emergency calls
Your service provider programs one or more emergency phone numbers that you can call under any circumstances. Emergency calls can be made without a SIM card, when your phone is locked, or when the SIM card is blocked.
Note: Emergency numbers vary by country.
Your phone’s preprogrammed emergency number(s) may not work in all locations, and sometimes an emergency call cannot be placed due to network, environmental, or interference issues.
Dial 911 or your local emergency number to be connected to an emergency response center. If you are on an active call, you must end it before making an emergency call.
When you make an emergency call, your phone’s GPS Enabled feature can help emergency service personnel find you, if you
56 call features are in a location where your phone's GPS antenna has established a clear view of the open sky and your local emergency response center has the equipment to process location information. Because of the limitations of this feature, always provide your location, to the best of your knowledge, to the emergency response center when you make an emergency call .
Note: Emergency calls cannot be placed while the keypad is locked, or if your phone is displaying a No Service message on the screen.
To unlock the keypad, press /* .
international calls
If your phone service includes international dialing, press and hold 0 to insert your local international access code (indicated by +).
Then, press the keypad keys to dial the country code and phone number.
speed dial
Each phone number stored in Contacts is assigned a Speed Dial number, which you can use to call that number.
1 From the home screen, use the keypad to enter the Speed Dial number assigned to the phone number you want to call.
2 Press # .
3 Press , .
turbo dial
The first nine entries in your contacts are set for turbo dial. They can be called by pressing and holding the speed dial number
(1 through 9).
voicemail
To receive voice mail messages, you must first set up a voice mail account with your service provider.
receiving a message
When you receive a voice mail message, New
VoiceMail Message appears on the display and the voicemail LED ( 7 ) icon will appear.
To call your service provider’s voice mail system and listen to the message:
1 Press K under Call .
2 To dismiss the message notification:
• Press r or Back .
If the caller leaves a message, this icon 3 appears on the display, reminding you that you have a new message.
call features 57
talkgroup calls
A group call is similar to a Push To Talk call, but is made to all members of a Talkgroup at once.
Before you can make or receive group calls, a
Talkgroup must be established. After the
Talkgroup is established, you must join the
Talkgroup.
joining a talkgroup
Your sales representative or your service provider establishes talkgroups for you and assigns each Talkgroup a Talkgroup number.
You can choose a name for each of your
Talkgroups when you create entries for them in Contacts.
To receive group calls made to any of these
Talkgroups, you must join the Talkgroup.
1 Press K under Contcs .
58 call features or
From the main menu, scroll to Contacts and press ; .
2 Scroll to the Talkgroup you want to join.
3 Press K under Join.
Note: You can only monitor one Talkgroup at a time.
making talkgroup calls
1 Press # . Then enter the Talkgroup number using the keypad. or
Choose the Talkgroup name from
Contacts or recent calls list.
2 Proceed as if making a Private call.
receiving talkgroup calls
To answer a group call:
• Proceed as if answering a Private call.
Only one person at a time may speak on a group call.
• The Private ID or name of the person who is speaking will appear on the display below the Talkgroup number.
turning off talkgroup calls
To set your phone to prevent you from hearing group calls to your Talkgroup:
Find it: / > Settings > Push to Talk >
Tkgrp Silent > On .
To set your phone to let you hear group calls to your Talkgroup:
Find it: / > Settings > Push to Talk >
Tkgrp Silent > Off .
call features 59
LINCaround
Note: This feature may not be offered by your service provider.
With LINCaround, you can make and receive
Two-Way Radio calls without network coverage. If you are travelling outside your service provider's coverage area, receiving a poor signal, or otherwise want to temporarily avoid using your service provider's network, you can switch to LINCaround and talk with anyone on your code and channel who is within range.
Note: Range will vary based on terrain, man-made structures and atmospheric conditions.
LINCaround lets you:
• Use code or private mode operation
• Use up to 10 channels
• Communicate with standalone
LINCaround radios
Note: You cannot use LINCaround with older
Family Radio Services products.
The following features and main menu items are unavailable while in LINCaround:
• On-network phone or Private calls
• Data transmission
• Incoming message notification
• Datebook
• Call forwarding
• Call Timers
• Call alerts
60 LINCaround
switching to
LINCaround
To set your phone to LINCaround:
1 From the home screen press / >
LINCaround and press r .
2 Select Go to LINCaround .
Switching to LINCaround Please Wait displays.
After a few seconds, the LINCaround idle screen displays. When LA Ready displays, you can begin using LINCaround.
While in LINCaround, this icon 4 displays.
exiting LINCaround
To switch to network mode:
1 From the LINCaround idle screen, press
/ > LA Options and press r .
2 Select Exit LINCaround .
Switching to Network Please Wait displays. After a few seconds, the network idle screen appears.
talk range
While in LINCaround mode, phones should be a minimum of 6 feet apart to maximize performance and improve transmission range.
channels and codes
Your phone has 10 channels and 15 codes.
Channels are divided into sets of frequencies.
Other parties may be talking on the same channel. Codes minimize interference from other parties when you are sharing the same channel.
LINCaround opens to the last code and channel used on your phone. You can view the code and channel your phone is currently set to on the LINCaround idle screen.
LINCaround 61
For code calls, all parties must be on the same channel and code. For private
LINCaround calls, the person you are calling must be in LINCaround and set to the same channel to receive your call.
Note: When making a code call, all parties that are on your code and channel can hear your conversation.
setting channels and codes
To set a channel:
1 From the LINCaround idle screen, press
K under Edit .
2 Scroll to Channel .
3 Press K under Edit .
4 Select a channel.
5 When you are finished, press K under
Back to return to the LINCaround idle screen.
62 LINCaround
To set a code:
1 From the LINCaround idle screen, press
K under Edit .
2 Scroll to Code .
3 Press K under Edit .
4 Select a code.
5 When you are finished, press K under
Back to return to the LINCaround idle screen.
making code calls
To make a code call:
1 From the LINCaround idle screen or the channel and code edit screen, press and hold the PTT button. Transmit appears on the first line of display. Begin speaking after your phone emits the LINCaround tone.
Note: The LINCaround tone consists of 4 rapid beeps.
2 Release the PTT button to listen.
If you receive an error message:
• No one is on your channel or code.
• You are out of range.
receiving code calls
When you receive a code call, Receive will appear on the display. After hearing the
LINCaround tone, you have 6 seconds to reply before the call times out.
To reply to the call, press the PTT button.
Note: An incoming LINCaround call can be terminated at any time by pressing .
.
receiving all LINCaround calls
If you set the code to Receive All , your phone can receive LINCaround transmissions from any phone that is set to the same channel, regardless of the code (1-15). When you receive transmissions with the code set to
Receive All , the code that the transmission was received on will replace Receive All on the display.
Note: You cannot initiate a code call when the code is set to Receive All .
To set the code to Receive All :
1 From the LINCaround idle screen, press
K under Edit .
2 Scroll to Code .
3 Press
K
under Edit .
4 Select Receive All .
5 When you are finished, press K under
Back to return to the LINCaround idle screen.
LINCaround 63
To reply to a call with the code set to Receive All :
• Press the PTT button.
private LINCaround calls
If you want to have a private conversation without other parties listening in, you can make a private LINCaround call. The person you are calling must be in LINCaround and set to the same channel to receive your call.
private only
To set LINCaround to ignore code calls, so that you only make or receive private
LINCaround calls, set your code to Pvt Only .
To set the code to Pvt Only :
1 From the LINCaround idle screen, press
K under Edit .
2 Scroll to Code .
3 Press K under Edit .
4 Select Pvt Only .
5 When you are finished, press K under
Back to return to the LINCaround idle screen.
making a private LINCaround call
1 Enter the PTN of the person you want to call on your channel. If the PTN is more than 10-digits, enter the last 10-digits of the PTN, or scroll to a number or name in
Contacts or the Recent Calls List.
2 Press and hold the PTT button. Begin speaking after your phone emits the
LINCaround tone.
3 Release the PTT button to listen.
6 4 LINCaround
The number or name of the person you are calling will appear in the display.
If you receive an error message:
• The PTN you entered is invalid.
• The person that you are trying to reach is in network mode.
• The person that you are trying to reach is set to a different channel.
• The person that you are trying to reach is out of range.
receiving a private LINCaround call
The number or name of the person who is calling will appear in the display. To reply, press the PTT button.
ending code calls and private
LINCaround calls
Code calls and private LINCaround calls will end automatically after 6 seconds of inactivity.
The LINCaround idle screen will display.
Note: A private or code LINCaround call can be interrupted during the 6 second idle time by another code call or private call.
making emergency calls while in LINCaround mode
If you attempt to make an Emergency 911 call while in LINCaround mode, your phone will automatically exit LINCaround mode and attempt to find a network signal.
If you are out of network coverage your phone will not be able to make an emergency 911
LINCaround 65
cellular call until you go back into the network coverage area.
You must wait until the phone reconnects to the network before attempting to make an emergency 911 cellular call.
setup options
You can set up LINCaround options on the LA
Options screen. You can access this screen in both network and LINCaround modes.
To access setup options:
1 Press / > LINCaround or LA Options.
2 Select Setup .
You can set the following LINCaround options:
• Direct Launch : Launch directly into
LINCaround when you select LINCaround from the main menu.
• State Tone : Have an alert sound notify you that you have used LINCaround for a specified interval.
using direct launch
To set your phone to launch LINCaround when you select LINCaround from the main menu:
1 From the Setup screen, scroll to
Direct Launch and press r .
2 Select On .
Note: If Direct Launch is set to On , the
LINCaround setup options will be unavailable from the main menu. However, you can still access setup options while in LINCaround by pressing / and selecting > LA Options > Setup .
To turn off Direct Launch:
1 From the Setup screen, scroll to Direct
Launch and press r .
2 Select Off .
66 LINCaround
LA Options will now display when you select
LINCaround from the main menu.
using state tone
To set your phone to alert you after you have used LINCaround for a specified interval:
1 From the Setup screen, scroll to State Tone and press r .
2 Select the interval after which you want the tone to sound.
For example, if you select 1 hour, you will be notified every hour that you are in
LINCaround.
To turn off State Tone:
1 From the Setup screen, scroll to State Tone and press r .
2 Select Off .
LINCaround 67
customize ring tones
To set the ring tone your phone makes when you receive phone calls, call alerts, message notifications, pictures sent using Send via PTT or Datebook reminders:
Find it: / > Ring Tones
1 Make sure Vibrate All is set to Off .
2 Scroll through the list of ring tones and select the one you want to assign.
Vibrate sets your phone to vibrate instead of making a sound. Silent sets your phone to neither vibrate nor make a sound.
3 Select the features you want to assign the ring tone to.
4 When you are finished, press K under
Done .
Note: This icon , appears on the display if you set your phone to Silent . This icon 5 appears on the display if you set the phone to
Vibrate All .
set your phone to vibrate
You can set your phone to vibrate instead of making a sound when you receive all phone calls, Push to Talk calls, group calls, PTT List calls, call alerts, message notifications, pictures sent using Send via PTT, and
Datebook reminders.
Find it: / > Ring Tones > Vibrate All
Set this option to On or Locked .
68 customize
Setting this option to On lets you turn Vibrate All off by pressing the up volume control. Setting this option to Locked requires you to press and hold the up volume control to turn Vibrate All off.
The Locked option helps prevent you from accidentally turning Vibrate All off.
To set Vibrate All to On or Locked using the volume controls:
Press the volume controls to turn down the volume as far as possible to set Vibrate All to On .
Continue to hold the down volume control to set Vibrate All to Locked .
To set your phone to vibrate instead of making a sound for some features but not others:
Find it: / > Ring Tones
1 Make sure Vibrate All is set to Off .
2 Select Vibrate from the list of ring tones.
3 Select the features you want to set to make no sound.
4 When you are finished, press K under
Done .
backlight
Set the amount of time that the display and java apps. backlights remain on, or turn off the backlight feature to extend battery life.
Find it: / > u > Display/Info > Backlight
LED indicators
You can turn off the Bluetooth, messaging, and voicemail indicators on the external display.
Find it: / > u > Display/Info > Backlight >
Bluetooth LED , Message LED , or VMail LED > Off customize 69
wallpaper
Set a previously saved photo or picture as a wallpaper (background) image in your phone’s external display, internal screen or throughout all menu screens.
Find it: / > u > Display/Info > Wallpaper
1 Select Wallpaper .
2 Scroll through the list of pictures and press r to select a picture.
You can set the wallpapers to change automatically after a certain period of time by turning on the Auto Cycle feature located in the
Wallpaper menu. You can select from 5 minutes ,
15 minutes , 1 hour , 8 hours , Daily , or Startup .
datebook
feature create datebook events see datebook event event reminder
To create a new Datebook event press / > Datebook >
[New Event] .
To see a calendar event press / > Datebook . Press ; left or right to see the day and ; up or down to see the events.
When an event reminder occurs press K under View .
Press K under Back to close the reminder.
70 customize
feature receive datebook events via
PTT
To view the information while still in the Push to Talk call press r .
The 5 most recent events received from a PTT ID are stored with that PTT ID on the recent calls list.
To store events to the
Datebook press
K
under
Save while viewing the event you want to store.
datebook setup
Find it: / > Datebook > / > Setup
You can view or change these options: options
Start View: Sets Datebook to start in day view, week view, or month view when you access Datebook.
Daily Begin: Sets the beginning of your day.
This is the earliest time of day displayed in week view, if you have a 12-hour day view.
Delete After: Sets the amount of time
Datebook waits to delete an event after it occurs.
Time Shift: Lets you shift the times of all
Datebook events. This is useful if you are traveling to a different time zone.
Alert Timeout: Sets the amount of time a tone continues to sound when you receive a
Datebook reminder.
customize 71
options
Clock: Controls whether the time and date appear on the home screen; sets time and date format; sets year.
hide or show location information
Your phone is equipped with a Location feature for use in connection with locationbased services that may be available in the future.
Turning Location On will allow the network to detect your position using GPS technology, making some applications and services easier to use. Turning Location off will disable the
GPS location function for all purposes except
911, but will not hide your general location based on the cell site serving your call. No application or service may use your location
72 customize without your request or permission. GPSenhanced 911 is not available in all areas.
set your privacy options
Find it: / > GPS > Privacy
Select from the following options: option
Restricted: No Java or similar software applications may view the location of your phone. However, location information may still be available to the phone’s owner, fleet manager, or account administrator.
Unrestricted: All applications may view the location of your phone, without notifying you.
option
Ask Access: When an application attempts to view the location of your phone, you will be prompted to give permission. However, location information may still be available to the phone’s owner, fleet manager, or account administrator.
change GPS PIN
When you receive your phone, your GPS PIN is 0000.
To change your GPS PIN press / > u >
Security > Change Passwords > GPS PIN . Enter the current GPS PIN and enter the new four to eight digit GPS PIN. Re-enter the new four- to eight-digit GPS PIN to confirm.
customize 73
Legal and Safety
Safety and General Information
This section contains important information on the safe and efficient operation of your mobile device. Read this information before using your integrated multi-service portable radio.*
Exposure to Radio Frequency (RF) Energy
Your mobile device contains a transmitter and receiver. When it is
ON, it receives and transmits RF energy. When you communicate with your phone, the system handling your call controls the power level at which your phone transmits.
Your mobile device is designed to comply with local regulatory requirements in your country concerning exposure of human beings to RF energy.
Portable Radio Product Operation and EME
Exposure
Your Motorola radio product is designed to comply with the following national and international standards and guidelines regarding exposure of human beings to radio frequency electromagnetic energy (EME):
7 4 Legal and Safety
• United States Federal Communications Commission, Code of Federal Regulations; 47 CFR part 2 sub-part J.
• American National Standards Institute (ANSI) / Institute of
Electrical and Electronics Engineers (IEEE). C95. 1-1992.
• Institute of Electrical and Electronics Engineers (IEEE).
C95. 1-2005 Edition.
*
• International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
• Ministry of Health (Canada). Safety Code 6. Limits of
Human Exposure to Radio frequency Electromagnetic
Fields in the Frequency Range from 3 kHz to 300 GHz,
1999.
• Australian Communications Authority Radio communications (Electromagnetic Radiation - Human
Exposure) Standard 2003.
• ANATEL, Brazil Regulatory Authority, Resolution 303 (July
2, 2002) “Regulation of the limitation of exposure to
* The information provided in this document supersedes the general safety information in user’s guides published prior to May 1, 2006
electrical, magnetic, and electromagnetic fields in the radio frequency range between 9 kHz and 300 GHz.”
“Attachment to Resolution 303 from July 2, 2002."
Operational Precautions
For optimal mobile device performance, and to be sure that human exposure to RF energy does not exceed the guidelines set forth in the relevant standards, always follow these instructions and precautions.
Phone Operation
When placing or receiving a phone call, hold your mobile phone as you would a landline telephone. Speak directly into the microphone .
Two-way radio operation
Your radio product has been designed and tested to comply with national and international standards and guidelines regarding human exposure to RF electromagnetic energy, when operated in the two-way mode (at the face, or at the abdomen when using an audio accessory) at usage factors of up to 50% talk/50% listen.
Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the PTT button. To receive calls, release the
PTT button. Transmitting 50% of the time or less, is important because this radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).
When using your radio product as a traditional two-way radio, hold the radio product in a vertical position with the microphone one to two inches (2.5 to 5 cm) away from the lips .
If you wear the mobile device on your body, always place the mobile device in a Motorola approved clip, holder, holster, case or body harness. If you do not use a body-worn accessory supplied or approved by Motorola and are not using the mobile device in the intended use positions along side the head in the phone mode or in front of the face in the two-way radio mode, or if you hang your device from a lanyard around your neck, keep the device at least 2.5 centimeters (1 inch) from your body when transmitting.
Approved Accessories
For a list of approved Motorola accessories call 1-800-453-0920, or visit our website at www.motorola.com/iden.
RF Energy Interference/Compatibility
Nearly every electronic device is subject to RF energy interference from external sources if inadequately shielded, designed or otherwise configured for RF energy compatibility. In some circumstances your mobile device may cause interference with other devices.
Legal and Safety 75
Follow Instructions to Avoid Interference
Problems
Turn OFF your mobile device in any location where posted notices instruct you to do so.
In an aircraft, turn off your mobile device whenever instructed to do so by airline staff. If your mobile device offers an airplane mode or similar feature, consult airline staff about using it in flight.
Implantable Medical Devices
If you have an implantable medical devices, such as a pacemaker or defibrillator, consult your physician before using this mobile device.
Persons with implantable medical devices should observe the following precautions:
• ALWAYS keep the mobile device more than 20 centimeters (8 inches) from the implantable medical device when the phone is turned ON.
• DO NOT carry the mobile device in the breast pocket;
• Use the ear opposite the implantable medical device to minimize the potential for interference.
• Turn OFF the mobile device immediately if you have any reason to suspect that interference is taking place.
Read and follow the directions from the manufacturer of your implantable medical device. If you have any questions about using your mobile device with your implantable medical device, consult your health care provider.
Hearing Aids
Some phones may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer or physician to discuss alternatives.
Other Medical Devices and Health Care Facilities
If you use any other personal medical devices, consult your physician or the manufacturer or your device to determine if it is adequately shielded from RF energy. Turn off your radio product when instructed to do so in hospitals or health care facilities that may be using equipment that is sensitive to external RF energy.
Bluetooth
This device supports Bluetooth 1.2 including HSP, HFP, OPP, DUN,
PBAP, and BPP. In order for Bluetooth devices to communicate with one another, they must utilize the same Bluetooth profile. To determine the profiles supported by other Motorola devices, visit www.hellomoto.com/bluetooth. For other devices, contact their respective manufacturer.
Certain Bluetooth features including those listed may not be supported by all compatible Bluetooth-enabled devices, and/or the functionality of such features may be limited in certain devices, or by certain wireless carriers. Contact your wireless carrier about feature availability and functionality.
76 Legal and Safety
Caring for the Environment by
Recycling
This symbol on a Motorola product means the product should not be disposed of with household waste.
Disposal of your Mobile Device and Accessories
Please do not dispose of mobile devices or electrical accessories
(such as chargers, headsets, or batteries) with your household waste. These items should be disposed of in accordance with the national collection and recycling schemes operated by your local or regional authority. Alternatively, you may return unwanted mobile devices and electrical accessories to any Motorola Approved
Service Center in your region. Details of Motorola approved national recycling schemes, and further information on Motorola recycling activities can be found at: www.motorola.com/recycling
Disposal of your Mobile Device Packaging and
User’s Guide
Product packaging and user’s guides should only be disposed of in accordance with national collection and recycling requirements.
Please contact your regional authorities for more details.
Driving Precautions
The use of wireless phones while driving may cause distraction.
Discontinue a call if you can’t concentrate on driving.
Additionally, the use of wireless devices and their accessories may be prohibited or restricted in certain areas. Always obey the laws and regulations on the use of these products.
Responsible driving practices can be found in the “Smart Practices
While Driving” section (see page 90).
Operational Warnings
Obey all posted signs when using Mobile devices in public areas.
Potentially Explosive Atmospheres
Areas with potentially explosive atmospheres are often but not always posted, and can include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, or areas where the air contains chemicals or particles, such as grain, dust or metal powders.
When you are in such area, turn off your handset, and do not remove, install, or charge batteries unless it is a radio product type especially qualified for use in such areas as “Intrinsically Safe” (for example, Factory Mutual, CSA, or UL approved). In such areas, sparks can occur and cause an explosion or fire.
Legal and Safety 77
Symbol Key
Your battery, charger, or portable radio may contain symbols, defined as follows:
Symbol
032374o
032376o
032375o
Definition
Important safety information follows.
Do not dispose of your battery or phone in a fire.
Your battery or phone may require recycling in accordance with local laws.
Contact your local regulatory authorities for more information.
Do not throw your battery or phone in the trash.
Li Ion BATT
032378o
Your phone contains an internal lithium ion battery.
Do not let your battery, charger, or phone get wet.
Symbol Definition
Listening at full volume to music or voice through a headset may damage your hearing.
Batteries and Chargers
Caution: Improper treatment or use of batteries may present a danger of fire, explosion, leakage, or other hazard. For more information, see the “Battery Use and Battery Safety” section in this user’s guide.
Keep Your Mobile Device and Its Accessories
Away from Small Children
These products are not toys and may be hazardous to small children. For example:
• A choking hazard may exist for small, detachable parts.
• Improper use could result in loud sounds, possibly causing hearing injury.
• Improperly handled batteries could overheat and cause a burn.
Glass Parts
Some parts of your mobile device may be made of glass. This glass could break if the product is dropped on a hard surface or receives
78 Legal and Safety
a substantial impact. If glass breaks, do not touch or attempt to remove. Stop using your mobile device until the glass is replaced by a qualified service center.
Seizures/Blackouts
Some people may be susceptible to epileptic seizures or blackouts when exposed to flashing lights, such as when playing video games. These may occur even if a person has never had a previous seizure or blackout.
If you have experienced seizures or blackouts, or if you have a family history of such occurrences, please consult with your physician before playing video games or enabling a flashing-lights feature (if available) on your mobile device.
Discontinue use and consult a physician if any of the following symptoms occur: convulsion, eye or muscle twitching, loss of awareness, involuntary movements, or disorientation. It is always a good idea to hold the screen away from your eyes, leave the lights on in the room, take a 15-minute break every hour, and stop use if you are very tired.
Caution About High Volume Usage
Warning: Warning: Exposure to loud noise from any source for extended periods of time may affect your hearing. The louder the volume sound level, the less time is required before your hearing could be affected. To protect your hearing:
• Limit the amount of time you use headsets or headphones at high volume.
• Avoid turning up the volume to block out noisy surroundings.
• Turn the volume down if you can’t hear people speaking near you.
If you experience hearing discomfort, including the sensation of pressure or fullness in your ears, ringing in your ears, or muffled speech, you should stop listening to the device through your headset or headphones and have your hearing checked.
For more information about hearing, see our Web site at direct.motorola.com/hellomoto/nss/AcousticSafety.asp
(in English only).
Repetitive Motion
When you repetitively perform actions such as pressing keys or entering finger-written characters, you may experience occasional discomfort in your hands, arms, shoulders, neck, or other parts of your body. If you continue to have discomfort during or after such use, stop use and see a physician.
Service and Repairs
If you have questions or need assistance, we’re here to help.
Go to www.motorola.com/support , where you can select from a number of customer care options. You can also contact the
Motorola Customer Support Center at 1 (800) 453-0920 (United
Legal and Safety 79
States), 1 (877) 483-2840 (TTY, TDD United States for hearing impaired).
Export Law Assurances
This product is controlled under the export regulations of the
United States of America and Canada. The Governments of the
United States of America and Canada may restrict the exportation or re-exportation of this product to certain destinations. For further information contact the U.S. Department of Commerce or the
Canadian Department of Foreign Affairs and International Trade.
Battery Use and Safety
Important: Handle and store batteries properly to avoid injury or damage.
Most battery issues arise from improper handling of batteries, and particularly from the continued use of damaged batteries.
DON’Ts
• Don’t disassemble, crush, puncture, shred, or otherwise attempt to change the form of your battery.
• Don’t let the phone or battery come in contact with water.
Water can get into the phone’s circuits, leading to corrosion. If the phone and/or battery get wet, have them checked by your carrier or contact Motorola, even if they appear to be working properly.
80 Legal and Safety
• Don’t allow the battery to touch metal objects.
If metal objects, such as jewelry, stay in prolonged contact with the battery contact points, the battery could become very hot.
• Don’t place your battery near a heat source.
Excessive heat can damage the phone or the battery. High temperatures can cause the battery to swell, leak, or malfunction. Therefore:
• Do not dry a wet or damp battery with an appliance or heat source, such as a hair dryer or microwave oven.
DOs
• Avoid leaving your phone in your car in high temperatures.
• Do avoid dropping the battery or phone.
Dropping these items, especially on a hard surface, can potentially cause damage.
• Do contact your service provider or Motorola if your phone or battery has been damaged from dropping or high temperatures.
Important: Use Motorola Original products for quality assurance and safeguards. To aid consumers in identifying authentic Motorola batteries from non-original or counterfeit batteries (that may not have adequate safety protection), Motorola provides holograms on its batteries. Consumers should confirm that any battery they purchase has a “Motorola Original” hologram.
Motorola recommends you always use Motorola-branded batteries and chargers.
Motorola mobile devices are designed to work with Motorola batteries. If you see a message on your display such as I nvalid Battery or Unable to Charge , take the following steps:
• Remove the battery and inspect it to confirm that it has a
“Motorola Original” hologram;
• If there is no hologram, the battery is not a Motorola battery;
• If there is a hologram, replace the battery and retry charging it;
• If the message remains, contact a Motorola authorized service center.
Important: Motorola’s warranty does not cover damage to the phone caused by non-Motorola batteries and/or chargers.
Warning: Use of a non-Motorola battery or charger may present a risk of fire, explosion, leakage, or other hazard.
Proper and safe battery disposal and recycling: Proper battery disposal is not only important for safety, it benefits the environment. Consumers may recycle their used batteries in many retail or service provider locations. Additional information on proper disposal and recycling may be found on the Web:
• www.motorola.com/recycling
• www.rbrc.org/call2recycle/ (in English only)
Disposal: Promptly dispose of used batteries in accordance with local regulations. Contact your local recycling center or national recycling organizations for more information on how to dispose of batteries.
Warning: Never dispose of batteries in a fire because they may explode.
Battery Charging
Notes for charging your phone’s battery:
• When charging your battery, keep it near room temperature. Never expose batteries to temperatures below 0°C (32°F) or above 45°C (113°F) when charging.
• New batteries are not fully charged.
• New batteries or batteries stored for a long time may take more time to charge.
• Motorola batteries and charging systems have circuitry that protects the battery from damage from overcharging.
Specific Absorption Rate
Your model wireless phone meets the governmental requirements for exposure to radio waves.
Your mobile device is a radio transmitter and receiver. It is designed and manufactured to not exceed limits for exposure to radio frequency (RF) energy set by the Federal Communications
Legal and Safety 81
Commission (FCC) of the U.S. Government and by the Canadian regulatory authorities. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed for the safety of all persons, regardless of age or health, and to account for any variations in measurements.
The exposure standard for mobile devices employs a unit of measurement known as the Specific Absorption Rate (SAR). The
SAR limit set by the FCC and by the Canadian regulatory authorities is 1.6 watts per kilogram (W/kg), averaged over one gram of tissue. Tests for SAR are conducted using procedures accepted by the FCC and by Industry Canada with the mobile device transmitting at its highest certified power level in all tested frequencies. Although the SAR is determined at the highest certified power level, the actual SAR level of the mobile device while operating can be below the maximum value. This is because the mobile device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station, the lower the power output.
Before a mobile device is available for sale to the public in the U.S. and Canada, it must be tested and certified to the FCC and Industry
Canada that it does not exceed the limit established by each government for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body)
82 Legal and Safety submitted to the FCC and available for review by Industry Canada.
The highest SAR value for this mobile device when tested for use at the ear is 1.17 W/kg, and when worn on the body, as described in this guide, is 1.41 W/kg. Body-worn measurements can differ, depending upon available accessories and regulatory requirements. The SAR information includes the Motorola testing protocol, assessment procedure, and measurement uncertainty range for this product.
While there may be differences between the SAR levels of various mobile devices and at various positions, they meet the governmental requirements for safe exposure. Please note that improvements to this product model could cause differences in the
SAR value for later products; in all cases, products are designed to be within the guidelines.
Additional information on SAR can be found on the Cellular
Telecommunications & Internet Association (CTIA) Web site: http://www.phonefacts.net
or the Canadian Wireless Telecommunications Association (CWTA)
Web site: http://www.cwta.ca
AGPS and Emergency Calls
When you make an emergency call, your mobile device can use
Assisted Global Positioning System (AGPS) satellite signals to tell the emergency response center your approximate location.
The AGPS feature has limitations, so always tell the emergency response center your best knowledge of your location. Remain on the phone for as long as the emergency response center instructs you.
AGPS might not work for emergency calls, if your local emergency response center does not process AGPS location information. For details, contact your local authorities.
If your mobile device cannot find strong AGPS satellite signals, the location of the nearest cell tower in contact with your mobile device is automatically provided to the emergency response center.
AGPS Performance Tips
• Go outside and away from underground locations, covered vehicles, structures with metal or concrete roofs, tall buildings, and foliage. Indoor performance might improve if you move closer to windows, but some window sun shielding films can block satellite signals.
• Move away from radios, entertainment equipment, and other electronic devices that might interfere with or block
AGPS satellite signals.
AGPS uses satellites controlled by the U.S. government and subject to changes implemented in accordance with the
Department of Defense AGPS user policy and the Federal Radio
Navigation Plan. These changes might affect AGPS performance.
Motorola Limited Warranty for the
United States and Canada
What Does this Warranty Cover?
Note: FOR IDEN SUBSCRIBER PRODUCTS, ACCESSORIES
AND SOFTWARE PURCHASED IN THE UNITED STATES OR
CANADA
Subject to the exclusions contained below, Motorola, Inc. warrants its Motorola iDEN Digital Mobile and Portable Handsets
("Products"), Motorola-branded or certified accessories sold for use with these Products ("Accessories") and Motorola software contained on CD-Roms or other tangible media and sold for use with these Products ("Software") to be free from defects in materials and workmanship under normal consumer usage for the period(s) outlined below. This limited warranty is a consumer's exclusive remedy, and applies as follows to new Products, Accessories and Software purchased by consumers in the United States or Canada, which are accompanied by this written warranty:
Products Covered
Products as defined above.
Length of Coverage
One (1) year from the date of purchase by the first consumer purchaser of the product.
Legal and Safety 83
Products Covered
Accessories as defined above.
Products or
Accessories that are
Repaired or
Replaced.
Software as defined above. Applies only to physical defects in the media that embodies the copy of the software
(e.g. CD-ROM, or floppy disk).
Length of Coverage
One (1) year from the date of purchase by the first consumer purchaser of the product.
The balance of the original warranty or for ninety (90) days from the date returned to the consumer, whichever is longer.
Ninety (90) days from the date of purchase.
What is not covered? (Exclusions)
Normal Wear and Tear . Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage.
Ornamental Decorations . Ornamental decorations such as emblems, graphics, rhinestones, jewels, gemstones and their settings, and other decorative elements, are excluded from coverage.
Batteries . Only batteries whose fully charged capacity falls below
80% of their rated capacity and batteries that leak are covered by this limited warranty.
Abuse & Misuse . Defects or damage that result from: (a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.) to the surface of the product resulting from misuse; (b) contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; (c) use of the Products or Accessories for commercial purposes or subjecting the Product or Accessory to abnormal usage or conditions; or (d) other acts which are not the fault of Motorola, are excluded from coverage.
Use of Non-Motorola Products and Accessories . Defects or damage that result from the use of Non-Motorola branded or certified Products, Accessories, Software or other peripheral equipment are excluded from coverage.
Unauthorized Service or Modification . Defects or damages resulting from service, testing, adjustment, installation, maintenance, alteration, including without limitation, software changes, or modification in any way by someone other than
Motorola, or its authorized service centers, are excluded from coverage.
Altered Products . Products or Accessories with (a) serial numbers or date tags that have been removed, altered or obliterated; (b) broken seals or that show evidence of tampering;
(c) mismatched board serial numbers; or (d) nonconforming or
8 4 Legal and Safety
non-Motorola housings, antennas, or parts, are excluded from coverage.
Communication Services . Defects, damages, or the failure of
Products, Accessories or Software due to any communication service or signal you may subscribe to or use with the Products,
Accessories or Software is excluded from coverage.
Software Embodied in Physical Media.
No warranty is made that the software will meet your requirements or will work in combination with any hardware or software applications provided by third parties, that the operation of the software products will be uninterrupted or error free, or that all defects in the software products will be corrected.
Software NOT Embodied in Physical Media . Software that is not embodied in physical media (e.g. software that is downloaded from the internet), is provided "as is" and without warranty.
Who is covered? This warranty extends only to the first consumer purchaser, and is not transferable.
What will Motorola Do? Motorola, at its option, will at no charge repair, replace or refund the purchase price of any Products,
Accessories or Software that does not conform to this warranty.
We may use functionally equivalent reconditioned/refurbished/pre-owned or new Products,
Accessories or parts. No data, software or applications added to your Product, Accessory or Software, including but not limited to personal contacts, games and ringer tones, will be reinstalled. To avoid losing such data, software and applications please create a back up prior to requesting service.
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
Motorola iDEN Customer Services 1-800-453-0920 or
954-723-4910
TTY-877-483-2840
Or visit us online at http://www.motorola.com/iden
You will receive instructions on how to ship the Products,
Accessories or Software, at your expense, to a Motorola
Authorized Repair Center. To obtain service, you must include: (a) a copy of your receipt, bill of sale or other comparable proof of purchase; (b) a written description of the problem; (c) the name of your service provider, if applicable; (d) the name and location of the installation facility (if applicable) and, most importantly; (e) your address and telephone number.
What Other Limitations Are There?
ANY IMPLIED
WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL
MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT, ACCESSORY OR SOFTWARE,
OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
Legal and Safety 85
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF
REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS,
ACCESSORIES OR SOFTWARE TO THE FULL EXTENT THESE
DAMAGES MAY BE DISCLAIMED BY LAW.
Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or limitation on the length of an implied warranty, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or from one jurisdiction to another.
Laws in the United States and other countries preserve for
Motorola certain exclusive rights for copyrighted Motorola software such as the exclusive rights to reproduce and distribute copies of the Motorola software. Motorola software may only be copied into, used in, and redistributed with, the Products associated with such Motorola software. No other use, including without limitation disassembly of such Motorola software or exercise of the exclusive rights reserved for Motorola, is permitted.
Patent and Software Provisions
MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and
Motorola will pay those costs and damages finally awarded
86 Legal and Safety against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following: a.That MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim; b.That MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and c.Should the Product or parts become, or in MOTOROLA'S opinion be likely to become, the subject of a claim of infringement of a
United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by
MOTOROLA.
MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the
Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product or any parts thereof.
Laws in the United States and other countries preserve for
MOTOROLA certain exclusive rights for copyrighted MOTOROLA
software, such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise or rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights.
Hearing Aid Compatibility With Mobile
Phones
Some Motorola phones are measured for compatibility with hearing aids. If the box for your particular model has “Rated for
Hearing Aids” printed on it, the following explanation applies.
When some mobile phones are used near some hearing devices
(hearing aids and cochlear implants), users may detect a buzzing, humming, or whining noise. Some hearing devices are more immune than others to this interference noise, and phones also vary in the amount of interference they generate.
The wireless telephone industry has developed ratings for some of their mobile phones, to assist hearing device users in finding phones that may be compatible with their hearing devices. Not all phones have been rated. Phones that are rated have the rating on their box or a label on the box.
The ratings are not guarantees. Results will vary depending on the user’s hearing device and hearing loss. If your hearing device happens to be vulnerable to interference, you may not be able to use a rated phone successfully. Trying out the phone with your hearing device is the best way to evaluate it for your personal needs.
M-Ratings: Phones rated M3 or M4 meet FCC requirements and are likely to generate less interference to hearing devices than phones that are not labeled. M4 is the better/higher of the two ratings.
T-Ratings: Phones rated T3 or T4 meet FCC requirements and are likely to be more usable with a hearing device’s telecoil (“T
Switch” or “Telephone Switch”) than unrated phones. T4 is the better/higher of the two ratings. (Note that not all hearing devices have telecoils in them.)
Hearing devices may also be measured for immunity to this type of interference. Your hearing device manufacturer or hearing health professional may help you find results for your hearing device. The more immune your hearing aid is, the less likely you are to experience interference noise from mobile phones.
Legal and Safety 87
Information From the World Health
Organization
Present scientific information does not indicate the need for any special precautions for the use of mobile phones. If you are concerned, you may want to limit your own or your children’s RF exposure by limiting the length of calls or by using hands-free devices to keep mobile phones away from your head and body.
Source: WHO Fact Sheet 193
Further information: http://www.who.int./peh-emf .
Product Registration
Online Product Registration: www.motorola.com/us/productregistration
Product registration is an important step toward enjoying your new
Motorola product. Registering permits us to contact you for product or software updates and allows you to subscribe to updates on new products or special promotions. Registration is not required for warranty coverage.
Please retain your original dated sales receipt for your records. For warranty service of your Motorola Personal Communications
Product you will need to provide a copy of your dated sales receipt to confirm warranty status.
Thank you for choosing a Motorola product.
Wireless: The New Recyclable
Your wireless phone can be recycled. Recycling your phone reduces the amount of waste disposed in landfills and allows recycled materials to be incorporated into new products.
The Cellular Telecommunications Industry Association (CTIA) and its members encourage consumers to recycle their phones and have taken steps to promote the collection and environmentally sound recycling of end-of-life devices.
As a phone user, you have an important role in ensuring that this device is recycled properly. When it comes time to give this phone up or trade it in for a new one, please remember that the phone, the charger, and many of its accessories can be recycled. It's easy.
To learn more about CTIA's Recycling Program for Used Wireless
Devices, please visit us at: http://recycling.motorola.young-america.com/ index.html
California Perchlorate Label
Some mobile phones use an internal, permanent backup battery on the printed circuit board that may contain very small amounts of perchlorate. In such cases, California law requires the following label:
Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate .
There is no special handling required by consumers.
88 Legal and Safety
Patent and Trademark Information
MOTOROLA, the Stylized M Logo and all other trademarks indicated as such herein are trademarks of Motorola, Inc. ® Reg.
U.S. Pat. & Tm. Off. © 2009 Motorola, Inc. All rights reserved.
Microsoft and Microsoft Internet Explorer are registered trademarks of Microsoft Corporation.
T9 is a trademark owned by Tegic Communications.
T9
®
Text Input Patent and Trademark Information.
This product is covered by U.S. Pat. 5,818,437, U.S. Pat. 5,953,541,
U.S. Pat. 6,011,554 and other patents pending.
Java and all other Java-based marks are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries.
All other product names or services mentioned in this manual are the property of their respective trademark owners.
Software Copyright Notice
Motorola products may include copyrighted Motorola and third party software stored in semiconductor memories or other media.
Laws in the United States and other countries preserve for
Motorola and third party software providers certain exclusive rights for copyrighted software, such as the exclusive rights to distribute or reproduce the copyrighted software. Accordingly, any copyrighted software contained in the Motorola products may not be modified, reverse-engineered, distributed, or reproduced in any manner to the extent allowed by law. Furthermore, the purchase of
Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents, or patent applications of Motorola or any third party software provider, except for the normal, non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product.
Privacy and Data Security
Motorola understands that privacy and data security are important to everyone. Because some features of your mobile device may affect your privacy or data security, please follow these recommendations to enhance protection of your information:
• Monitor access— Keep your mobile device with you and do not leave it where others may have unmonitored access. Lock your device’s keypad where this feature is available.
• Keep software up to date— If Motorola or a software/application vendor releases a patch or software fix for your mobile device that updates the device’s security, install it as soon as possible.
• Erase before recycling— Delete personal information or data from your mobile device prior to disposing of it or turning it in for recycling. For instructions on how to delete all personal information from your device, please contact your local service provider.
Legal and Safety 89
• Understanding AGPS— To provide location information for emergency calls, certain Motorola mobile devices incorporate Assisted Global Positioning System (AGPS) technology. AGPS technology also can be used in non-emergency applications to track and monitor a user’s location—for example, to provide driving directions. Users who prefer not to permit such tracking and monitoring should avoid using such applications.
If you have further questions regarding how the use of your mobile device may impact your privacy or data security, please contact
Motorola at [email protected]
, or contact your service provider.
Smart Practices While Driving
Drive Safe, Call Smart
SM
Check the laws and regulations on the use of phones and their accessories in the areas where you drive. Always obey them. The use of these devices may be prohibited or restricted in certain areas—for example handsfree use only. Go to www.motorola.com/callsmart (in English only) for more information.
Your mobile device lets you communicate by voice and data—almost anywhere, anytime, wherever wireless service is available and safe conditions allow. When driving a car, driving is your first responsibility. If you choose to use your phone while driving, remember the following tips:
90 Legal and Safety
• Get to know your Motorola mobile device and its features such as speed dial and redial. If available, these features help you to place your call without taking your attention off the road.
• When available, use a handsfree device. If possible, add an additional layer of convenience to your phone with one of the many Motorola Original handsfree accessories available today.
• Position your mobile device within easy reach. Be able to access your phone without removing your eyes from the road. If you receive an incoming call at an inconvenient time, if possible, let your voice mail answer it for you.
• Let the person you are speaking with know you are driving; if necessary, suspend the call in heavy traffic or hazardous weather conditions. Rain, sleet, snow, ice, and even heavy traffic can be hazardous.
• Do not take notes or look up phone numbers while driving. Jotting down a “to do” list or going through your address book takes attention away from your primary responsibility, driving safely.
• Dial sensibly and assess the traffic; if possible, place calls when your car is not moving or before pulling into traffic. If you must make a call while moving, dial only a few numbers, check the road and your mirrors, then continue.
• Do not engage in stressful or emotional conversations that may be distracting. Make people you are talking with aware you are driving and suspend conversations that can divert your attention away from the road.
• Use your mobile device to call for help. Dial 911 or other local emergency number in the case of fire, traffic accident, or medical emergencies (wherever wireless phone service is available).
• Use your mobile device to help others in emergencies. If you see an auto accident, crime in progress, or other serious emergency where lives are in danger, call 911 or other local emergency number
(wherever wireless phone service is available), as you would want others to do for you.
• Call roadside assistance or a special non-emergency wireless assistance number when necessary. If you see a broken-down vehicle posing no serious hazard, a broken traffic signal, a minor traffic accident where no one appears injured, or a vehicle you know to be stolen, call roadside assistance or other special non-emergency wireless number (wherever wireless phone service is available).
Legal and Safety 91
index
A
3-way calls 15 call waiting 15
alert
B
92 index
setting your phone 50 turning on or off 50
C call
edit/delete 18 set ringer ID 18
D
receive events via PTT 71 setup 71
drafts
see also text messages, drafts
E
F frequently asked questions
G
GPS enabled
H
I
L
LINCaround
channels, setting 62 code calls, making 62
switching to 61 switching to network mode 61 talk range 61
M
message center
index 93
modem
N
O
optional accessory 9 optional feature 9
P
PTT List calls
Push to Talk calls
R
received calls 53 recent calls 53
ring tones
off 68 setting 68 vibrate 68, 69
9 4 index
S safety
change SIM PIN 36 enable SIM PIN 36
T
text messages 19, 28 creating 19
V
voicemail 57 message indicator 57 receiving 57 setting up 57
W
Y
index 95
advertisement