Opel Crossland X 2019.75 Owner's manual

Opel Crossland X 2019.75 Owner's manual
Owner's Manual
Contents
Introduction .................................... 2
In brief ............................................ 6
Keys, doors and windows ............ 20
Seats, restraints ........................... 40
Storage ........................................ 61
Instruments and controls ............. 69
Lighting ...................................... 100
Climate control ........................... 109
Driving and operating ................. 121
Vehicle care ............................... 174
Service and maintenance .......... 214
Technical data ........................... 221
Customer information ................ 232
Index .......................................... 246
2
Introduction
Introduction
Introduction
Vehicle specific data
Please enter your vehicle's data on
the previous page to keep it easily
accessible.
Please refer to the sections "Service
and maintenance", "Technical data",
the vehicle’s identification plate and
national registration documents.
Introduction
Your vehicle is a designed
combination of advanced technology,
safety, environmental friendliness
and economy.
This Owner's Manual provides you
with all the necessary information to
enable you to drive your vehicle
safely and efficiently.
Make sure your passengers are
aware of the possible risk of accident
and injury which may result from
improper use of the vehicle.
You must always comply with the
specific laws and regulations of the
country that you are in. These laws
may differ from the information in this
Owner's Manual.
Disregarding the description given in
this manual may affect your warranty.
When this Owner's Manual refers to a
workshop visit, we recommend your
Opel Service Partner.
When this Owner's Manual refers to a
workshop visit, we recommend your
Vauxhall Authorised Repairer.
All Opel Service Partners provide
first-class service at reasonable
prices. Experienced mechanics
trained by Opel work according to
specific Opel instructions.
All Vauxhall Authorised Repairers
provide first-class service at
reasonable prices. Experienced
mechanics trained by Vauxhall work
according to specific Vauxhall
instructions.
The customer literature pack should
always be kept ready to hand in the
vehicle.
Using this manual
●
This manual describes all options
and features available for this
model. Certain descriptions,
including those for display and
●
●
●
●
●
●
●
3
menu functions, may not apply to
your vehicle due to model
variant, country specifications,
special equipment or
accessories.
The "In brief" section will give you
an initial overview.
The table of contents at the
beginning of this manual and
within each section shows where
the information is located.
The index will enable you to
search for specific information.
The Owner's Manual uses the
engine identifier code. The
corresponding sales designation
and engineering code can be
found in the section "Technical
data".
Directional data, e.g. left or right,
or front or back, always relate to
the direction of travel.
Displays may not support your
specific language.
Display messages and interior
labelling are written in bold
letters.
4
Introduction
Danger, Warnings and
Cautions
9 Danger
Text marked 9 Danger provides
information on risk of fatal injury.
Disregarding this information may
endanger life.
9 Warning
Text marked 9 Warning provides
information on risk of accident or
injury. Disregarding this
information may lead to injury.
Caution
Text marked Caution provides
information on possible damage to
the vehicle. Disregarding this
information may lead to vehicle
damage.
Symbols
Page references are indicated with 3.
3 means "see page".
Chronological order to select menu
entries in the vehicle personalisation
is indicated with I.
Page references and index entries
refer to the indented headings given
in the section table of content.
Thank you for choosing a Vauxhall.
We wish you many hours of
pleasurable driving.
Your Vauxhall Team
Your Opel Team
Introduction
5
6
In brief
In brief
Vehicle unlocking
Tailgate
Press c to unlock the vehicle. Open
the doors by pulling the handles.
Press P to unlock the tailgate only.
With electronic key system the
vehicle is unlocked by passing the
hand behind one of the front door
handles or by pressing the tailgate
button.
Press tailgate button and open the
tailgate.
Radio remote control 3 21.
Central locking system 3 23.
Electronic key system 3 22.
Load compartment 3 29.
Initial drive information
In brief
Seat adjustment
Backrests inclination
Seat height
Turn handwheel. Do not lean on
backrest when adjusting.
Seat position 3 41.
Seat adjustment 3 42.
Lever pumping motion
up
: seat higher
down : seat lower
Longitudinal adjustment
Pull handle, slide seat, release
handle. Try to move the seat back and
forth to ensure that the seat is locked
in place.
Seat position 3 41.
Seat adjustment 3 42.
Seat position 3 41.
Seat adjustment 3 42.
7
8
In brief
Seat inclination
Head restraint adjustment
Seat belt
Press switch
top
: front end higher
bottom : front end lower
Press release button, adjust height,
engage.
Head restraints 3 40.
Pull out the seat belt and fasten in belt
buckle. The seat belt must not be
twisted and must fit close against the
body. The backrest must not be tilted
back too far (maximum approx. 25°).
To unfasten belt, press red button on
belt buckle.
Seat position 3 41.
Seat belts 3 46.
Airbag system 3 49.
Seat position 3 41.
Seat adjustment 3 42.
In brief
Mirror adjustment
9
Exterior mirrors
Steering wheel adjustment
Select the relevant exterior mirror by
pushing the mirror button to the left or
right. Adjust respective mirror by the
four-way control.
Convex mirrors 3 33.
Electric adjustment 3 33.
Folding mirrors 3 34.
Heated mirrors 3 34.
Unlock lever, adjust steering wheel,
then engage lever and ensure it is
fully locked. Do not adjust steering
wheel unless vehicle is stationary and
steering wheel lock has been
released.
Seat position 3 41.
Ignition switch positions 3 123.
Power button 3 123
Interior mirror
To adjust the mirror, move the mirror
housing in the desired direction.
Manual anti-dazzle interior mirror
3 35.
Automatic anti-dazzle interior mirror
3 35.
10
In brief
Instrument panel overview
In brief
1
2
3
Power windows ..................... 36
Exterior mirrors ..................... 33
Cruise control ..................... 140
4
Speed limiter ....................... 143
Heated steering wheel ......... 70
Turn lights ........................... 104
Headlight flash .................... 102
High beam ........................... 101
High beam assist ............... 101
Exit lighting ......................... 107
Parking lights ...................... 105
5
6
Buttons for Driver
Information Centre ................ 88
Side air vents ...................... 118
Instruments .......................... 77
Driver Information Centre ...... 88
7 Infotainment controls ........... 70
8 Windscreen wiper and
washer, rear wiper and
washer ................................. 71
9 Head-up display .................... 92
10 Centre air vents .................. 118
11
12
13
14
Hazard warning flashers .... 103
Info Display .......................... 90
Centre air vent .................... 119
Light sensor ........................ 101
Rain sensor ........................... 71
Sun sensor .......................... 113
15 Central locking system .......... 23
16 Glovebox .............................. 61
Fuse box ............................ 192
17 Controls for Info Display
operation ............................... 90
18 Climate control system ........ 109
19 USB port .............................. 74
20 Electronic Stability Control
and Traction Control ........... 139
Lane departure warning ..... 163
Stop-start system ................ 126
Parking assist ..................... 150
Advanced parking assist .... 153
Electric child locks ................ 28
21 Power outlet .......................... 74
22 Selector lever ...................... 133
23 Parking brake ...................... 138
24
25
26
27
28
29
11
Power button ....................... 123
Ignition switch ..................... 123
Steering wheel adjustment . . 70
Horn ..................................... 71
Bonnet release lever .......... 176
Storage ................................. 61
Fuse box ............................ 192
30 Head-up display .................... 92
31 Light switch ........................ 100
Headlight range
adjustment ......................... 102
Front fog lights ................... 104
Rear fog light ...................... 105
Instrument illumination ....... 106
12
In brief
Exterior lighting
Headlight flash and high beam
Turn lights
AUTO : automatic light control
switches automatically
between daytime running
light and headlight
: sidelights
8
: headlights
9
pull : headlight flash
push : high beam
up
: right turn light
down : left turn light
High beam 3 101.
High beam assist 3 101.
Headlight flash 3 102.
LED headlights 3 103.
Turn lights 3 104.
Parking lights 3 105.
Automatic light control 3 101.
Front fog lights 3 104.
Rear fog light 3 105.
In brief
Hazard warning flashers
Horn
13
Washer and wiper systems
Windscreen wiper
Operated by pressing ¨.
Hazard warning flashers 3 103.
Press j.
HI
LO
INT
: fast
: slow
: interval wiping
or
AUTO : automatic wiping with rain
sensor
OFF : off
1x
: single wipe
Windscreen wiper 3 71.
14
In brief
Windscreen washer
Rear window wiper
Rear window washer
Pull.
Windscreen washer system 3 71.
Washer fluid 3 178.
OFF : off
INT : intermittent operation
ON : continuous operation
Push.
Washer fluid is sprayed on the rear
window and the wiper wipes a few
times.
Rear window wiper / washer 3 73.
In brief
Climate control
Heated rear window
The heating is operated by pressing
b.
Heated rear window 3 38.
Heated exterior mirrors 3 34.
Demisting and defrosting the
windows
●
●
●
●
●
●
●
Press à: the air distribution is
directed towards the windscreen.
Set temperature controller £ to
warmest level.
Switch on air conditioning A/C if
required.
Set fan speed Z to highest level.
Switch on heated rear window b.
Switch on heated
windscreen ,.
Open side air vents as required
and direct them towards the door
windows.
Climate control systems 3 109.
Heated windscreen 3 38.
15
16
In brief
Transmission
Automatic transmission
Starting off
Check before starting off
Manual transmission
●
●
●
●
To engage reverse on 6-speed
transmission, pull the ring.
Manual transmission 3 136.
P
R
N
D
M
<
]
:
:
:
:
:
:
:
park position
reverse
neutral mode
automatic mode
manual mode
upshift
downshift
Automatic transmission 3 133.
●
tyre pressure 3 196 and
condition
engine oil level and fluid levels
3 177
all windows, mirrors, exterior
lighting and number plates are
free from dirt, snow and ice and
are operational
proper position of mirrors 3 33,
seats 3 41 and seat belts
3 47
brake function at low speed,
particularly if the brakes are wet
In brief
Starting the engine
Ignition switch
●
Diesel engine: wait until control
indicator ! for preheating
extinguishes.
● Turn key to position 2 and
release after engine has been
started.
Starting the engine 3 124.
Power button
●
●
●
●
●
Turn key to position 1.
Move the steering wheel slightly
to release the steering wheel
lock.
Manual transmission: operate
clutch and brake pedal.
Automatic transmission: operate
brake pedal and move selector
lever to P or N.
Do not operate accelerator pedal.
17
●
●
●
Manual transmission: operate
clutch and brake pedal.
Automatic transmission: operate
brake pedal and move selector
lever to P or N.
Do not operate accelerator pedal.
Press Start/Stop button.
Release button after starting
procedure begins.
18
In brief
Stop-start system
Parking
9 Warning
●
If the vehicle is at a low speed or at a
standstill and certain conditions are
fulfilled, an Autostop is activated.
An Autostop is indicated by control
indicator D.
Manual transmission: to restart the
engine, depress the clutch pedal
again. Control indicator D
extinguishes.
Automatic transmission: to restart the
engine, release the brake pedal.
Control indicator D extinguishes.
Stop-start system 3 126.
●
●
●
Do not park the vehicle on an
easily ignitable surface. The
high temperature of the
exhaust system could ignite the
surface.
Always apply the parking
brake. Activate the parking
brake without pressing the
release button. Apply as firmly
as possible on a downhill slope
or uphill slope. Depress brake
pedal at the same time to
reduce operating force.
Switch off the engine.
If the vehicle is on a level
surface or uphill slope, engage
first gear or set the selector
lever to position P. On an uphill
slope, turn the front wheels
away from the kerb.
If the vehicle is on a downhill
slope, engage reverse gear or
set the selector lever to position
●
●
●
●
●
P. Turn the front wheels
towards the kerb.
Close the windows.
Remove the ignition key from
the ignition switch or switch off
ignition on vehicles with power
button. Turn the steering wheel
until the steering wheel lock is
felt to engage.
Lock the vehicle with e on the
radio remote control.
Or with electronic key system
press marking on front door
handles 3 22.
Activate the anti-theft alarm
system 3 31.
The engine cooling fans may run
after the engine has been
switched off 3 176.
Caution
After running at high engine
speeds or with high engine loads,
operate the engine briefly at a low
load or run in neutral for
In brief
approx. 30 seconds before
switching off, in order to protect
the turbocharger.
Caution
Under extreme cold temperatures,
idle engine for maximum
5 minutes otherwise the engine
might be damaged.
Keys, locks 3 20.
Laying-up the vehicle for a long
period of time 3 175.
19
20
Keys, doors and windows
Keys, doors and
windows
Keys, locks ................................... 20
Keys .......................................... 20
Radio remote control ................. 21
Electronic key system ................ 22
Central locking system .............. 23
Automatic locking ...................... 28
Child locks ................................. 28
Doors ........................................... 29
Load compartment .................... 29
Vehicle security ............................ 30
Anti-theft locking system ........... 30
Anti-theft alarm system .............. 31
Immobiliser ................................ 33
Exterior mirrors ............................ 33
Convex shape ........................... 33
Electric adjustment .................... 33
Folding mirrors .......................... 34
Heated mirrors ........................... 34
Interior mirrors ............................. 35
Manual anti-dazzle .................... 35
Automatic anti-dazzle ................ 35
Windows ...................................... 35
Windscreen ............................... 35
Manual windows ........................ 36
Power windows ......................... 36
Heated rear window .................. 38
Heated windscreen .................... 38
Sun visors .................................. 38
Roof ............................................. 39
Glass panel ............................... 39
Keys, locks
Keys
Caution
Do not attach heavy or bulky items
to the ignition key.
Replacement keys
The key number is specified on a
detachable tag.
The key number must be quoted
when ordering replacement keys as it
is a component of the immobiliser
system.
Locks 3 210.
Central locking 3 23.
Starting the engine 3 124.
Radio remote control 3 21.
Electronic key 3 22.
The code number of the adapter for
the locking wheel nuts is specified on
a card. It must be quoted when
ordering a replacement adapter.
Wheel changing 3 202.
Keys, doors and windows
Key with foldaway key section
Radio remote control
21
The remote control has a range of up
to 100 m, but may also be much less
due to external influences. The
hazard warning flashers confirm
operation.
Handle with care, protect from
moisture and high temperatures and
avoid unnecessary operation.
Replacing battery in radio remote
control
Replace the battery as soon as the
range reduces.
Press button to extend. To fold the
key, first press the button.
Lock cylinders
Designed to free-wheel if they are
forcefully rotated without the correct
key or if the correct key is not fully
inserted. To reset, turn cylinder with
the correct key until its slot is vertical,
remove key then re-insert it. If the
cylinder still free-wheels, turn the key
through 180° and repeat operation.
Enables operation of the following
functions via the use of the remote
control buttons:
● central locking system 3 23
● anti-theft locking system 3 30
● anti-theft alarm system 3 31
● tailgate unlocking 3 23
● power windows 3 36
● mirrors folding
Batteries do not belong in household
waste. They must be disposed of at
an appropriate recycling collection
point.
22
Keys, doors and windows
Fault
1. To unclip the cover insert a small
screwdriver between the back
cover and the remote control.
2. Remove the back cover.
3. Extract the flat battery from its
location.
4. Replace battery with a battery of
the same type. Pay attention to
the installation position.
5. Clip the cover in place.
If the central locking system cannot
be operated with the radio remote
control, the cause may be one of the
following:
● Fault in radio remote control.
● The range is exceeded.
● The battery voltage is too low.
● Frequent, repeated operation of
the radio remote control while not
in range.
● Overload of the central locking
system by operating at frequent
intervals, the power supply is
interrupted for a short time.
● Interference from higher-power
radio waves from other sources.
Manual unlocking 3 23.
Electronic key system
Enables a keyless operation of the
following functions:
● central locking system 3 23
● ignition switching on and starting
the engine 3 124
The electronic key simply needs to be
on the driver's person.
Additionally, the electronic key
includes the functionality of the radio
remote control 3 21.
Handle with care, protect from
moisture and high temperatures and
avoid unnecessary operation.
Keys, doors and windows
Fault
Replacing battery in electronic
key
Replace the battery as soon as the
system no longer operates properly
or the range is reduced. The need for
battery replacement is indicated by a
message in the Driver Information
Centre 3 94.
Batteries do not belong in household
waste. They must be disposed of at
an appropriate recycling collection
point.
23
1. To unclip the cover insert a small
screwdriver in the cutout.
2. Remove the cover.
3. Extract the flat battery from its
location.
4. Replace battery with a battery of
the same type. Pay attention to
the installation position.
5. Clip the cover in place.
If the central locking cannot be
operated or the engine cannot be
started, the cause may be one of the
following:
● Fault in electronic key.
● Electronic key is out of reception
range.
● The battery voltage is too low.
● Overload of the central locking
system by operating at frequent
intervals, the power supply is
interrupted for a short time.
● Interference from higher-power
radio waves from other sources.
To rectify the cause of the fault,
change the position of the electronic
key.
Manual unlocking 3 23.
Central locking system
Unlocks and locks doors, load
compartment and fuel filler flap.
Pull an interior door handle fully to
unlock and open the respective door.
24
Keys, doors and windows
Note
In the event of an accident in which
airbags or belt pretensioners are
deployed, the vehicle is
automatically unlocked.
Automatic locking 3 28
Rigid key
Unlocking
Unlocking mode can be set in the
vehicle personalisation menu in the
Info Display. Two settings are
selectable:
● All doors, load compartment and
fuel filler flap will be unlocked by
turning the key once.
● Only the driver's door and fuel
filler flap will be unlocked by
turning the key once. To unlock
entire vehicle, turn the key twice.
Vehicle personalisation 3 95.
Turn key in the driver's door lock
cylinder.
If the vehicle is not closed properly,
the central locking system will not
work.
Remote control operation
Unlocking
Locking
Close doors, load compartment and
fuel filler flap.
Press O.
Turn key in the driver's door lock
cylinder.
Keys, doors and windows
Unlocking mode can be set in the
vehicle personalisation menu in the
Info Display. Two settings are
selectable:
● All doors, load compartment and
fuel filler flap will be unlocked by
pressing O once.
● Only the driver's door and fuel
filler flap will be unlocked by
pressing O once. To unlock entire
vehicle, press O twice.
Vehicle personalisation 3 95.
Unlocking the tailgate
Press P longer to unlock the
tailgate only.
Vehicle personalisation 3 95.
Unlocking and opening the tailgate
3 29.
Locking
Close doors, load compartment and
fuel filler flap.
25
Electronic key system operation
Press N.
If the vehicle is not closed properly,
the central locking system will not
work.
Confirmation
Operation of the central locking
system is confirmed by the hazard
warning flashers.
The electronic key must be outside
the vehicle, within a range of approx.
1 m of the relevant door side.
26
Keys, doors and windows
Unlocking
●
Entire vehicle will be unlocked by
passing hand behind one of the
front door handles or by pressing
the tailgate button.
● Only the tailgate will be unlocked
by pressing the tailgate button.
Vehicle personalisation 3 95
Locking
Pass hand behind one of the front
door handles to unlock the vehicle or
press the tailgate button.
Unlocking mode can be set in the
vehicle personalisation. Three
settings are selectable:
● Only the driver's door and fuel
filler flap will be unlocked by
passing hand behind the driver's
door handle.
If the vehicle is not closed properly,
the electronic key remains in the
vehicle or the ignition is not off,
locking will not be permitted and a
warning chime sounds.
Unlocking and opening the tailgate
The tailgate can be unlocked and
opened by pushing the tailgate button
when the electronic key is in range.
The doors remain locked depending
on the configuration in the vehicle
personalisation.
Load compartment 3 29
Vehicle personalisation 3 95
Confirmation
Operation of central locking system is
confirmed by the hazard warning
flashers.
Central locking button
Press marking of the front door
handles.
Entire vehicle will be locked.
Locks or unlocks entire vehicle from
the passenger compartment via a
switch.
Keys, doors and windows
27
Manual locking
Press Q to lock. The LED in the button
illuminates.
Press Q again to unlock. The LED in
the button extinguishes.
Operation with the key in case of
a central locking system fault
In case of a fault, e.g. vehicle battery
or remote control / electronic key
battery is discharged, the vehicle can
be locked or unlocked with the
mechanical key.
Manual unlocking
Electronic key: press and hold the
latch to extract the integral key.
Manually unlock the driver's door by
inserting and turning the key in the
lock cylinder. With working central
locking system the vehicle will be
unlocked.
By switching on the ignition, the antitheft locking system is deactivated.
The other doors can be opened by
pulling the interior handle. The load
compartment and fuel filler flap will
possibly not be unlocked.
Manually lock the driver's door by
inserting and turning the key in the
lock cylinder. With working central
locking system the vehicle will be
locked.
28
Keys, doors and windows
If the vehicle is not closed properly,
the automatic locking does not take
place. This is signalled by the sound
of the locks rebounding,
accompanied by illumination of h in
the instrument panel, an audible
signal and the display of an alert
message.
Activation or deactivation
Automatic relock after unlocking
This feature automatically relocks the
vehicle a short time after unlocking
with the remote control or electronic
key, provided vehicle has not been
opened.
Child locks
9 Warning
Use the child locks whenever
children are occupying the rear
seats.
To lock the other doors, first remove
the black cover by inserting a key and
turning clockwise.
Insert key into the recess and move
latch sideways.
Remove key and attach the black
cover.
The fuel filler flap and tailgate are
possibly not locked.
Automatic locking
Automatic locking after driving off
This system allows automatic locking
as soon as the speed of the vehicle
exceeds 10 km/h.
Mechanical child locks
With the ignition on, press Q until an
audible signal starts and a
corresponding message is displayed.
The state of the system stays in
memory when switching off the
ignition.
Keys, doors and windows
Turn the red child lock in the rear
doors to the horizontal position by
using a key. The door cannot be
opened from the inside.
To deactivate, turn the child lock to
the vertical position.
Switching on
Press Ô. The indicator lamp in the
button comes on, accompanied by a
confirmation message. This indicator
lamp remains on until the child lock is
switched off.
Electric child locks
Switching off
Press Ô again. The indicator lamp on
button goes off, accompanied by a
confirmation message.
Remotely operated system to prevent
opening of the rear doors using the
interior handles.
29
Doors
Load compartment
Tailgate
Opening
Press the tailgate button and open the
tailgate.
30
Keys, doors and windows
Closing
gases, which cannot be seen or
smelled, could enter the vehicle.
This can cause unconsciousness
and even death.
Caution
Use the interior handle.
Do not push the tailgate button whilst
closing as this will open the tailgate
again.
Central locking system 3 23.
General hints for operating
tailgate
9 Danger
Do not drive with the tailgate open
or ajar, e.g. when transporting
bulky objects, since toxic exhaust
Before opening the tailgate, check
overhead obstructions, e.g. a
garage door, to avoid damage to
the tailgate. Always check the
moving area above and behind the
tailgate.
Note
The installation of certain heavy
accessories onto the tailgate may
affect its ability to remain open.
Note
At low outside temperatures the
tailgate may not open fully by itself.
In this event, lift the tailgate manually
to its normal end position.
Vehicle security
Anti-theft locking system
9 Warning
Do not use the system if there are
people in the vehicle! The doors
cannot be unlocked from the
inside.
The system deadlocks all the doors.
All doors must be closed otherwise
the system cannot be activated.
Unlocking the vehicle disables the
mechanical anti-theft locking system.
This is not possible with the central
locking button.
Keys, doors and windows
Activating
31
It monitors:
● doors, tailgate, bonnet
● passenger compartment
including adjoining load
compartment
● vehicle inclination, e.g. if it is
raised
● ignition
Activation
Press N on the radio remote control
twice within 5 seconds.
Or with electronic key system press
twice the marking on one of the front
door handles.
Anti-theft alarm system
The anti-theft alarm system is
combined with the anti-theft locking
system.
The anti-theft alarm system is
combined with the central locking
system.
All doors must be closed.
The electronic key of the electronic
key system must not remain in the
vehicle.
● Radio remote control: activated
30 seconds after locking the
vehicle by pressing e once.
● Electronic key system: activated
30 seconds after locking the
vehicle by pressing marking on
one of the front door handles.
●
●
Radio remote control: directly by
pressing e twice within
5 seconds.
Electronic key system: directly by
pressing twice the marking on
one of the front door handles.
Note
Changes to the vehicle interior such
as the use of seat covers and open
windows, could impair the function
of passenger compartment
monitoring.
32
Keys, doors and windows
Activation without monitoring of
passenger compartment and
vehicle inclination
3. Close doors.
4. Activate the anti-theft alarm
system.
Indication
LED in the o button flashes if the
anti-theft alarm system is activated.
Seek the assistance of a workshop in
the event of faults.
Deactivation
Radio remote control: Unlocking the
vehicle by pressing c deactivates the
anti-theft alarm system.
Switch off the monitoring of
passenger compartment and vehicle
inclination when animals are being
left in the vehicle, because of high
volume ultrasonic signals and
because movements could trigger the
alarm. Also switch off when the
vehicle is on a ferry or train.
1. Close tailgate, bonnet, windows.
2. Press o. LED in the button o
illuminates for a maximum of
10 minutes.
Electronic key system: Unlocking the
vehicle by pressing marking on one of
the front door handles deactivates the
anti-theft alarm system.
The electronic key must be outside
the vehicle, within a range of approx.
1 m of the relevant door side.
The system is not deactivated by
unlocking the driver's door with the
key or with the central locking button
in the passenger compartment.
Alarm
When triggered, the alarm siren
sounds and the hazard warning lights
flash simultaneously. The number
and duration of alarm signals are
stipulated by legislation.
The anti-theft alarm system can be
deactivated by pressing c or
switching on the ignition.
Electronic key system: The anti-theft
alarm system can be deactivated by
pressing marking on one of the front
door handles.
A triggered alarm, which has not been
interrupted by the driver, will be
indicated by the hazard warning
Keys, doors and windows
lights. They will flash quickly four
times the next time the vehicle is
unlocked with the radio remote
control.
If the vehicle's battery is to be
disconnected (e.g. for maintenance
work), the alarm siren must be
deactivated as follows: switch the
ignition on then off, then disconnect
the vehicle's battery within
15 seconds.
If the battery has been reconnected
(e.g. after maintenance work), wait for
10 minutes to restart the engine.
Note
The immobiliser does not lock the
doors. Always lock the vehicle after
leaving it 3 23.
Switch on the anti-theft alarm
system 3 31.
Emergency operation of electronic
key 3 123.
33
Exterior mirrors
Convex shape
The shape of the mirror makes
objects appear smaller, which will
affect the ability to estimate
distances.
Electric adjustment
Immobiliser
The system checks whether the
vehicle is allowed to be started with
the key being used.
The immobiliser is activated
automatically at the end of a trip.
Note
Radio Frequency Identification
(RFID) tags may cause interference
with the key. Do not have it placed
near the key when starting the
vehicle.
Select the relevant exterior mirror by
pushing the mirror button to the left or
right.
Then swivel the control to adjust the
mirror.
34
Keys, doors and windows
Folding mirrors
Electric folding
Heated mirrors
For pedestrian safety, the exterior
mirrors will swing out of their normal
mounting position if they are struck
with sufficient force. Reposition the
mirror by applying slight pressure to
the mirror housing.
Pull mirror button rearwards. Both
exterior mirrors will fold.
Pull mirror button rearwards again to
return both exterior mirrors to their
original position.
If an electrically folded mirror is
manually extended, pulling mirror
button rearwards will only electrically
extend the other mirror.
Operated by pressing b.
Heating works with the engine
running and is switched off
automatically after a short time.
Heated rear window 3 38.
Keys, doors and windows
Interior mirrors
Automatic anti-dazzle
Manual anti-dazzle
35
Windows
Windscreen
Windscreen stickers
To reduce dazzle, adjust the lever on
the underside of the mirror housing.
Dazzle from following vehicles is
automatically reduced, when driving
in the dark.
Do not attach stickers such as toll
road stickers or similar on the
windscreen in the area of the interior
mirror. Keep the sensor free from
dust, dirt and ice. Otherwise the
detection zone of the rain sensor /
light sensor and the view area of the
camera in the mirror housing could be
restricted.
Sensors 3 71, 3 101
36
Keys, doors and windows
Windscreen replacement
Caution
If the vehicle has a front-looking
camera sensor for the driver
assistance systems, it is very
important that any windscreen
replacement is performed
accurately according to Opel
specifications. Otherwise, these
systems may not work properly
and there is a risk of unexpected
behaviour and / or messages from
these systems.
If the vehicle has a front-looking
camera sensor for the driver
assistance systems, it is very
important that any windscreen
replacement is performed
accurately according to Vauxhall
specifications. Otherwise, these
systems may not work properly
and there is a risk of unexpected
behaviour and / or messages from
these systems.
Manual windows
The rear door windows can be
opened or closed manually with the
window cranks.
Power windows
9 Warning
Take care when operating the
power windows. Risk of injury,
particularly to children.
If there are children on the rear
seats, switch on the child safety
system for the power windows.
Keep a close watch on the
windows when closing them.
Ensure that nothing becomes
trapped in them as they move.
Switch on ignition to operate power
windows.
Operate the switch for the respective
window by pushing to open or pulling
to close.
Pushing or pulling gently to the first
detent: window moves up or down as
long as the switch is operated.
Pushing or pulling firmly to the second
detent then releasing: window moves
up or down automatically with safety
function enabled. To stop movement,
operate the switch once more in the
same direction.
Keys, doors and windows
Safety function
If the window glass encounters
resistance above the middle of the
window during automatic closing, it is
immediately stopped and opened
again.
37
Child safety system for rear
windows
Override safety function
In the event of closing difficulties due
to frost or the like, switch on the
ignition, then pull the switch to the first
detent and hold. The window moves
up without safety function enabled.
To stop movement, release the
switch.
Press V to deactivate rear door
power windows; the LED illuminates.
To activate, press V again.
Press and hold e to close windows.
Release button to stop window
movement.
If the windows are fully closed, the
hazard warning lights will flash twice.
Operating windows from outside
Overload
The windows can be operated
remotely from outside the vehicle.
If the windows are repeatedly
operated within short intervals, the
window operation is disabled for
some time.
38
Keys, doors and windows
Initialising the power windows
If the windows cannot be closed
automatically (e.g. after
disconnecting the vehicle battery), a
warning message is displayed in the
Driver Information Centre.
Vehicle messages 3 94.
Activate the window electronics as
follows:
1. Close doors.
2. Switch on ignition.
3. Pull switch until the window is
closed and keep pulling for
additional 2 seconds.
4. Push switch until the window is
completely open and keep
pushing for additional 2 seconds.
5. Repeat for each window.
Heated rear window
Operated by pressing b.
Heating works with the engine
running and is switched off
automatically after a short time.
Depending on climate control system,
b is located at a different position.
Heated exterior mirrors 3 34.
Heated windscreen
Operated by pressing ,. LED in
button illuminates.
Heating works with the engine
running and is switched off
automatically after a short time.
Depending on climate control
system, , is located at a different
position.
Sun visors
The sun visors can be folded down or
swivelled to the side to prevent
dazzling.
The covers of the mirrors should be
closed when driving.
A ticket holder is located on the
backside of the sun visor.
Keys, doors and windows
Roof
Glass panel
Sunblind
The sunblind is electrically operated.
Press N firmly to the second detent
and then release at the front: the
sunblind is completely closed.
Safety function
If the sunblind encounters resistance
during automatic closing, it is
immediately stopped and opened
again.
Initialising after a power failure
Press N gently to the first detent at
the rear: the sunblind is opened as
long as the switch is operated.
Press N firmly to the second detent
and then release at the rear: the
sunblind is completely opened.
Press N gently to the first detent at
the front: the sunblind is closed as
long as the switch is operated.
After a power failure, it may only be
possible to operate the sunblind to a
limited extent. Initialise the system as
follows:
1. Switch on ignition.
2. Press N twice gently to the first
detent at the rear, the sunblind
opens slightly.
3. Immediately press N twice gently
to the first detent at the front, the
sunblind closes slightly.
After step 3 the sunblind is in
initialising mode without safety
function.
39
4. Press N gently to the first detent
at the rear until the sunblind is
completely opened.
5. Press N gently to the first detent
at the front until the sunblind is
completely closed.
After this procedure, the sunblind is
initialised with safety function
activated.
When N is pressed firmly to the
second detent during initialising, the
procedure is cancelled.
40
Seats, restraints
Seats, restraints
Head restraints
Height adjustment
Position
Head restraints ............................ 40
Front seats ................................... 41
Seat position .............................. 41
Seat adjustment ........................ 42
Armrest ...................................... 44
Heating ...................................... 44
Rear seats ................................... 45
Armrest ...................................... 45
Seat belts ..................................... 46
Three-point seat belt ................. 47
Airbag system .............................. 49
Front airbag system ................... 52
Side airbag system .................... 52
Curtain airbag system ............... 53
Airbag deactivation .................... 54
Child restraints ............................. 55
Child restraint systems .............. 55
Child restraint installation
locations ................................... 58
Head restraints on front seats
9 Warning
Only drive with the head restraint
set to the proper position.
Press release button, adjust height,
engage.
The upper edge of the head restraint
should be at upper head level. If this
is not possible for extremely tall
people, set to highest position, and
set to lowest position for small people.
Seats, restraints
Head restraints on rear seats
Front seats
Height adjustment
Seat position
41
9 Warning
Only drive with the seat correctly
adjusted.
9 Danger
Do not sit closer than 25 cm to the
steering wheel, to permit safe
airbag deployment.
Pull the head restraint upwards or
press the catch to release and push
the head restraint downwards.
Removal of rear head restraint
E.g. when using a child restraint
system 3 55.
Pull the head restraint upwards, press
the catch to release and pull the head
restraint out.
●
9 Warning
Never adjust seats while driving as
they could move uncontrollably.
●
Sit with buttocks as far back
against the backrest as possible.
Adjust the distance between the
seat and the pedals so that legs
are slightly angled when fully
pressing the pedals. Slide the
front passenger seat as far back
as possible.
Set seat height high enough to
have a clear field of vision on all
sides and on instrument cluster.
There should be at least one
hand of clearance between head
and the roof frame. Thighs
should rest lightly on the seat
without pressing into it.
42
Seats, restraints
●
Sit with shoulders as far back
against the backrest as possible.
Set the backrest rake so that it is
possible to easily reach the
steering wheel with arms slightly
bent. Maintain contact between
shoulders and the backrest when
turning the steering wheel. Do
not angle the backrest too far
back. We recommend a
maximum rake of approx. 25°.
Adjust seat and steering wheel in
a way that the wrist rests on top
of the steering wheel while the
arm is fully extended and
shoulders on the backrest.
Adjust the steering wheel 3 70.
Adjust the head restraint 3 40.
Adjust the thigh support so that
there is a space approx. two
fingers wide between the edge of
the seat and the hollow of the
knee.
Adjust the lumbar support so that
it supports the natural shape of
the spine.
●
●
●
●
●
Seat adjustment
Backrest inclination
Drive only with engaged seats and
backrests.
Longitudinal adjustment
Turn handwheel. Do not lean on
backrest when adjusting.
Pull handle, slide seat, release
handle. Try to move the seat back and
forth to ensure that the seat is locked
in place.
Seats, restraints
43
Seat height
Seat inclination
Lumbar support
Lever pumping motion
up
: seat higher
down : seat lower
Press switch
top
: front end higher
bottom : front end lower
Adjust lumbar support using the fourway switch to suit personal
requirements.
Moving support up and down: push
switch up or down.
Increasing and decreasing support:
push switch forwards or backwards.
44
Seats, restraints
Adjustable thigh support
Armrest
Pull the lever and slide the thigh
support.
Armrest can be folded up.
Heating
Adjust heating to the desired setting
by pressing ß for the respective seat
one or more times. The control
indicator in the button indicates the
setting.
Prolonged use of the highest setting
for people with sensitive skin is not
recommended.
Seat heating is operational when
engine is running.
During an Autostop, seat heating is
also operational.
Stop-start system 3 126.
Seats, restraints
Rear seats
Drive only with engaged seats and
backrests.
9 Warning
Pull handle, slide seat, release
handle. Try to move the seat back and
forth to ensure that the seat is locked
in place.
Armrest
Backrest inclination
Never adjust seats while driving as
they could move uncontrollably.
Folding backrests 3 62.
Longitudinal adjustment
Both parts of the rear seat can be
individually moved forwards or
backwards.
Folding down armrest 3 62.
Pull the loop, adjust inclination and
release loop. Do not lean on backrest
when adjusting.
45
46
Seats, restraints
Seat belts
The seat belts are locked during
heavy acceleration or deceleration of
the vehicle, holding the occupants in
the seat position. Therefore the risk of
injury is considerably reduced.
9 Warning
Fasten seat belt before each trip.
In the event of an accident, people
not wearing seat belts endanger
their fellow occupants and
themselves.
Belt pretensioners
Seat belts are designed to be used by
only one person at a time.
Child restraint system 3 55.
Periodically check all parts of the belt
system for damage, soiling and
proper functionality.
Have damaged components
replaced. After an accident, have the
belts and triggered belt pretensioners
replaced by a workshop.
In the event of a head-on, rear-end or
side-on collision of a certain severity,
the front and rear seat belts are
tightened. The front seat belts are
tightened by two pretensioners per
seat. The outer rear seat belts are
tightened by one pretensioner per
seat.
Note
Make sure that the belts are not
damaged by shoes or sharp-edged
objects or trapped. Prevent dirt from
getting into the belt retractors.
Incorrect handling (e.g. removal or
fitting of belts) can trigger the belt
pretensioners.
Seat belt reminder
Each seat is equipped with a seat belt
reminder, indicated by a control
indicator X for the respective seat in
the roof console 3 81.
Belt force limiters
Stress on the body is reduced by the
gradual release of the belt during a
collision.
9 Warning
Deployment of the belt pretensioners
is indicated by continuous illumination
of control indicator v 3 82.
Triggered belt pretensioners must be
replaced by a workshop. Belt
pretensioners can only be triggered
once.
Note
Do not affix or install accessories or
other objects that may interfere with
the operation of the belt
pretensioners. Do not make any
Seats, restraints
47
Unfasten
modifications to belt pretensioner
components as this will invalidate
the operating permit of your vehicle.
Three-point seat belt
Fasten
Loose or bulky clothing prevents the
belt from fitting snugly. Do not place
objects such as handbags or mobile
phones between the belt and your
body.
Withdraw the belt from the retractor,
guide it untwisted across the body
and insert the latch plate into the
buckle. Tighten the lap belt regularly
whilst driving by pulling the shoulder
belt.
9 Warning
The belt must not rest against hard
or fragile objects in the pockets of
your clothing.
Seat belt reminder X 3 81.
To release belt, press red button on
belt buckle.
Centre seat belt of the second
seat row
The centre seat is equipped with a
particular three-point seat belt.
48
Seats, restraints
Pull latch plates with the belt out of
belt holder in the roof.
Insert lower latch plate into left-hand
buckle (1) at the centre seat. Guide
the upper latch plate with the belt over
the lap area and the shoulder (do not
twist) and insert it into right-hand
buckle (2) at centre seat.
To unfasten the seat belt, first press
the button on the right-hand buckle
(2) and remove upper latch plate.
Then press the button on the lefthand buckle (1) and remove lower
latch plate. The seat belt retracts
automatically.
Using the seat belt while pregnant
9 Warning
The lap belt must be positioned as
low as possible across the pelvis
to prevent pressure on the
abdomen.
Seats, restraints
Airbag system
The airbag system consists of a
number of individual systems
depending on the scope of
equipment.
When triggered, the airbags inflate
within milliseconds. They also deflate
so quickly that it is often unnoticeable
during the collision.
9 Warning
The airbag system deploys in an
explosive manner, repairs must be
performed by skilled personnel
only.
9 Warning
Adding accessories that change
the vehicle's frame, bumper
system, height, front end or side
sheet metal, may keep the airbag
system from working properly. The
operation of the airbag system can
also be affected by changing any
parts of the front seats, seat belts,
airbag sensing and diagnostic
module, steering wheel,
instrument panel, inner door seals
including the speakers, any of the
airbag modules, ceiling or pillar
trim, front sensors, side impact
sensors or airbag wiring.
Note
The airbag systems and belt
pretensioner control electronics are
located in the centre console area.
Do not put any magnetic objects in
this area.
Do not affix any objects onto the
airbag covers and do not cover them
with other materials. Have damaged
covers replaced by a workshop.
Each airbag is triggered only once.
Have deployed airbags replaced by
a workshop. Furthermore, it may be
necessary to have the steering
wheel, the instrument panel, parts of
the panelling, the door seals,
handles and the seats replaced.
Do not make any modifications to
the airbag system as this will
invalidate the vehicle operating
permit.
49
Control indicator v for airbag systems
3 82.
Child restraint systems on front
passenger seat with airbag
systems
Warning according to ECE R94.02:
EN: NEVER use a rearward-facing
child restraint on a seat protected by
an ACTIVE AIRBAG in front of it;
DEATH or SERIOUS INJURY to the
CHILD can occur.
DE: Nach hinten gerichtete
Kindersitze NIEMALS auf einem Sitz
verwenden, der durch einen davor
befindlichen AKTIVEN AIRBAG
50
Seats, restraints
geschützt ist, da dies den TOD oder
SCHWERE VERLETZUNGEN DES
KINDES zur Folge haben kann.
FR: NE JAMAIS utiliser un siège
d'enfant orienté vers l'arrière sur un
siège protégé par un COUSSIN
GONFLABLE ACTIF placé devant lui,
sous peine d'infliger des
BLESSURES GRAVES, voire
MORTELLES à l'ENFANT.
ES: NUNCA utilice un sistema de
retención infantil orientado hacia
atrás en un asiento protegido por un
AIRBAG FRONTAL ACTIVO. Peligro
de MUERTE o LESIONES GRAVES
para el NIÑO.
RU: ЗАПРЕЩАЕТСЯ
устанавливать детское
удерживающее устройство лицом
назад на сиденье автомобиля,
оборудованном фронтальной
подушкой безопасности, если
ПОДУШКА НЕ ОТКЛЮЧЕНА! Это
может привести к СМЕРТИ или
СЕРЬЕЗНЫМ ТРАВМАМ
РЕБЕНКА.
NL: Gebruik NOOIT een achterwaarts
gericht kinderzitje op een stoel met
een ACTIEVE AIRBAG ervoor, om
DODELIJK of ERNSTIG LETSEL van
het KIND te voorkomen.
DA: Brug ALDRIG en bagudvendt
autostol på et forsæde med AKTIV
AIRBAG, BARNET kan komme i
LIVSFARE eller komme ALVORLIGT
TIL SKADE.
SV: Använd ALDRIG en bakåtvänd
barnstol på ett säte som skyddas med
en framförvarande AKTIV AIRBAG.
DÖDSFALL eller ALLVARLIGA
SKADOR kan drabba BARNET.
FI: ÄLÄ KOSKAAN sijoita taaksepäin
suunnattua lasten turvaistuinta
istuimelle, jonka edessä on
AKTIIVINEN TURVATYYNY, LAPSI
VOI KUOLLA tai VAMMAUTUA
VAKAVASTI.
NO: Bakovervendt
barnesikringsutstyr må ALDRI brukes
på et sete med AKTIV
KOLLISJONSPUTE foran, da det kan
føre til at BARNET utsettes for
LIVSFARE og fare for ALVORLIGE
SKADER.
PT: NUNCA use um sistema de
retenção para crianças voltado para
trás num banco protegido com um
AIRBAG ACTIVO na frente do
mesmo, poderá ocorrer a PERDA DE
VIDA ou FERIMENTOS GRAVES na
CRIANÇA.
IT: Non usare mai un sistema di
sicurezza per bambini rivolto
all'indietro su un sedile protetto da
AIRBAG ATTIVO di fronte ad esso:
pericolo di MORTE o LESIONI
GRAVI per il BAMBINO!
EL: ΠΟΤΕ μη χρησιμοποιείτε παιδικό
κάθισμα ασφαλείας με φορά προς τα
πίσω σε κάθισμα που προστατεύεται
από μετωπικό ΕΝΕΡΓΟ ΑΕΡΟΣΑΚΟ,
διότι το παιδί μπορεί να υποστεί
ΘΑΝΑΣΙΜΟ ή ΣΟΒΑΡΟ
ΤΡΑΥΜΑΤΙΣΜΟ.
PL: NIE WOLNO montować fotelika
dziecięcego zwróconego tyłem do
kierunku jazdy na fotelu, przed
którym znajduje się WŁĄCZONA
PODUSZKA POWIETRZNA.
Niezastosowanie się do tego
zalecenia może być przyczyną
ŚMIERCI lub POWAŻNYCH
OBRAŻEŃ u DZIECKA.
Seats, restraints
TR: Arkaya bakan bir çocuk emniyet
sistemini KESİNLİKLE önünde bir
AKTİF HAVA YASTIĞI ile
korunmakta olan bir koltukta
kullanmayınız. ÇOCUK ÖLEBİLİR
veya AĞIR ŞEKİLDE
YARALANABİLİR.
UK: НІКОЛИ не використовуйте
систему безпеки для дітей, що
встановлюється обличчям назад,
на сидінні з УВІМКНЕНОЮ
ПОДУШКОЮ БЕЗПЕКИ, інакше це
може призвести до СМЕРТІ чи
СЕРЙОЗНОГО ТРАВМУВАННЯ
ДИТИНИ.
HU: SOHA ne használjon hátrafelé
néző biztonsági gyerekülést előlről
AKTÍV LÉGZSÁKKAL védett ülésen,
mert a GYERMEK HALÁLÁT vagy
KOMOLY SÉRÜLÉSÉT okozhatja.
HR: NIKADA nemojte koristiti sustav
zadržavanja za djecu okrenut prema
natrag na sjedalu s AKTIVNIM
ZRAČNIM JASTUKOM ispred njega,
to bi moglo dovesti do SMRTI ili
OZBILJNJIH OZLJEDA za DIJETE.
SL: NIKOLI ne nameščajte otroškega
varnostnega sedeža, obrnjenega v
nasprotni smeri vožnje, na sedež z
AKTIVNO ČELNO ZRAČNO
BLAZINO, saj pri tem obstaja
nevarnost RESNIH ali SMRTNIH
POŠKODB za OTROKA.
SR: NIKADA ne koristiti bezbednosni
sistem za decu u kome su deca
okrenuta unazad na sedištu sa
AKTIVNIM VAZDUŠNIM
JASTUKOM ispred sedišta zato što
DETE može da NASTRADA ili da se
TEŠKO POVREDI.
MK: НИКОГАШ не користете детско
седиште свртено наназад на
седиште заштитено со АКТИВНО
ВОЗДУШНО ПЕРНИЧЕ пред него,
затоа што детето може ДА ЗАГИНЕ
или да биде ТЕШКО ПОВРЕДЕНО.
BG: НИКОГА не използвайте
детска седалка, гледаща назад,
върху седалка, която е защитена
чрез АКТИВНА ВЪЗДУШНА
ВЪЗГЛАВНИЦА пред нея - може да
се стигне до СМЪРТ или
СЕРИОЗНО НАРАНЯВАНЕ на
ДЕТЕТО.
RO: Nu utilizaţi NICIODATĂ un scaun
pentru copil îndreptat spre partea din
spate a maşinii pe un scaun protejat
de un AIRBAG ACTIV în faţa sa;
51
acest lucru poate duce la DECESUL
sau VĂTĂMAREA GRAVĂ a
COPILULUI.
CS: NIKDY nepoužívejte dětský
zádržný systém instalovaný proti
směru jízdy na sedadle, které je
chráněno před sedadlem AKTIVNÍM
AIRBAGEM. Mohlo by dojít k
VÁŽNÉMU PORANĚNÍ nebo ÚMRTÍ
DÍTĚTE.
SK: NIKDY nepoužívajte detskú
sedačku otočenú vzad na sedadle
chránenom AKTÍVNYM AIRBAGOM,
pretože môže dôjsť k SMRTI alebo
VÁŽNYM ZRANENIAM DIEŤAŤA.
LT: JOKIU BŪDU nemontuokite atgal
atgręžtos vaiko tvirtinimo sistemos
sėdynėje, prieš kurią įrengta AKTYVI
ORO PAGALVĖ, nes VAIKAS GALI
ŽŪTI arba RIMTAI SUSIŽALOTI.
LV: NEKĀDĀ GADĪJUMĀ
neizmantojiet uz aizmuguri vērstu
bērnu sēdeklīti sēdvietā, kas tiek
aizsargāta ar tās priekšā uzstādītu
AKTĪVU DROŠĪBAS SPILVENU, jo
pretējā gadījumā BĒRNS var gūt
SMAGAS TRAUMAS vai IET BOJĀ.
52
Seats, restraints
ET: ÄRGE kasutage tahapoole
suunatud lapseturvaistet istmel, mille
ees on AKTIIVSE TURVAPADJAGA
kaitstud iste, sest see võib
põhjustada LAPSE SURMA või
TÕSISE VIGASTUSE.
MT: QATT tuża trażżin għat-tfal li
jħares lejn in-naħa ta’ wara fuq sit
protett b’AIRBAG ATTIV quddiemu;
dan jista’ jikkawża l-MEWT jew
ĠRIEĦI SERJI lit-TFAL.
GA: Ná húsáid srian sábháilteachta
linbh cúil RIAMH ar shuíochán a
bhfuil mála aeir ag feidhmiú os a
chomhair. Tá baol BÁIS nó GORTÚ
DONA don PHÁISTE ag baint leis.
Beyond the warning required by
ECE R94.02, for safety reasons a
forward-facing child restraint system
must only be used subject to the
instructions and restrictions in the
table 3 58.
The airbag label is located on both
sides of the front passenger sun visor.
Airbag deactivation 3 54.
Front airbag system
The front airbag system consists of
one airbag in the steering wheel and
one in the instrument panel on the
front passenger side. These can be
identified by the word AIRBAG.
The front airbag system is triggered in
the event of a front-end impact of a
certain severity. The ignition must be
switched on.
9 Warning
Optimum protection is only
provided when the seat is in the
proper position.
Seat position 3 41.
Keep the area in which the airbag
inflates clear of obstructions.
Fit the seat belt correctly and
engage securely. Only then is the
airbag able to protect.
Side airbag system
The inflated airbags cushion the
impact, thereby reducing the risk of
injury to the upper body and head of
the front seat occupants
considerably.
Seats, restraints
The side airbag system consists of an
airbag in each front seat backrest.
This can be identified by the word
AIRBAG.
The side airbag system is triggered in
the event of a side impact of a certain
severity. The ignition must be
switched on.
53
9 Warning
Keep the area in which the airbag
inflates clear of obstructions.
Note
Only use protective seat covers that
have been approved for the vehicle.
Be careful not to cover the airbags.
Curtain airbag system
The curtain airbag system consists of
an airbag in the roof frame on each
side. This can be identified by the
word AIRBAG on the roof pillars.
The curtain airbag system is triggered
in the event of a side-on impact of a
certain severity. The ignition must be
switched on.
The inflated airbags cushion the
impact, thereby reducing the risk of
injury to the upper body and pelvis in
the event of a side-on collision
considerably.
The inflated airbags cushion the
impact, thereby reducing the risk of
injury to the head in the event of a
side-on impact considerably.
9 Warning
Keep the area in which the airbag
inflates clear of obstructions.
The hooks on the handles in the
roof frame are only suitable for
hanging up light articles of
clothing, without coat hangers. Do
not keep any items in these
clothes.
54
Seats, restraints
Airbag deactivation
The front passenger airbag system
must be deactivated for child restraint
system on the passenger seat
according to the instructions in the
table 3 58. The side airbag and
curtain airbag systems, the belt
pretensioners and all driver airbag
systems will remain active.
Switch positions:
*OFF : front passenger airbag is
deactivated and will not
inflate in the event of a
collision. Control indicator
*OFF illuminates
continuously in the centre
console
ÓON : front passenger airbag is
active
9 Danger
The front passenger airbag system
can be deactivated via a keyoperated switch on the passenger
side of the instrument panel.
Change status only when the vehicle
is stopped with the ignition off.
Deactivate passenger airbag only
in combination with the use of a
child restraint system, subject to
the instructions and restrictions in
the table 3 58.
Otherwise, there is a risk of fatal
injury for a person occupying a
seat with a deactivated front
passenger airbag.
If the control indicator ÓON
illuminates for approx. 60 seconds
after the ignition is switched on, the
front passenger airbag system will
inflate in the event of a collision.
If the control indicator *OFF
illuminates after the ignition is
switched on, the front passenger
airbag system is deactivated. It stays
on while the airbag is deactivated.
If both control indicators are
illuminated at the same time, there is
a system failure. The status of the
system is not discernible, therefore
no person is allowed to occupy the
front passenger seat. Contact a
workshop immediately.
Seats, restraints
Consult a workshop immediately if
neither of the two control indicators
are illuminated.
Control indicator for airbag
deactivation 3 82.
Child restraints
Child restraint systems
9 Danger
If using a rear-facing child restraint
system on the front passenger
seat, the airbag system for the
front passenger seat must be
deactivated. This also applies to
certain forward-facing child
restraint systems as indicated in
the tables 3 58.
Airbag deactivation 3 54.
Airbag label 3 49.
We recommend a child restraint
system which is tailored specifically to
the vehicle. For further information,
contact your workshop.
Before fastening a child seat adjust
the head restraint 3 40.
When a child restraint system is being
used, pay attention to the following
usage and installation instructions
and also those supplied with the child
restraint system.
55
Always comply with local or national
regulations. In some countries, the
use of child restraint systems is
forbidden on certain seats.
Child restraint systems can be
fastened with:
● Three-point seat belt
● ISOFIX brackets
● Top-tether anchor
Three-point seat belt
Child restraint systems can be
fastened by using a three-point seat
belt. After fastening the child restraint
system the seat belt has to be
tightened 3 58.
56
Seats, restraints
ISOFIX brackets
Either a Top-tether strap or a support
leg must be used in addition to the
ISOFIX brackets.
In addition to the ISOFIX brackets,
fasten the Top-tether strap to the
Top-tether anchors.
ISOFIX child restraint systems of
universal category positions are
marked in the table by IUF 3 58.
Selecting the right system
i-Size child seats and vehicle seats
with i-Size approval are marked with
i-Size symbol, see illustration.
Fasten vehicle-approved ISOFIX
child restraint systems to the ISOFIX
brackets. Specific vehicle ISOFIX
child restraint system positions are
marked in the ISOFIX table 3 58.
ISOFIX brackets are indicated by a
label on the backrest.
An i-Size child restraint system is an
universal ISOFIX child restraint
system according UN Regulation No.
129.
All i-Size child restraint systems can
be used on any vehicle seat suitable
for i-Size, i-Size table 3 58.
Top-tether anchors
Top-tether anchors are marked with
the symbol : for a child seat.
The rear seats are the most
convenient location to fasten a child
restraint system.
Children should travel facing
rearwards in the vehicle as long as
possible. This makes sure that the
child's backbone, which is still very
weak, is under less strain in the event
of an accident.
Suitable are restraint systems that
comply with valid UN ECE
regulations. Check local laws and
regulations for mandatory use of child
restraint systems.
The following child restraints are
recommended for the following
weight classes:
● Maxi Cosi Cabriofix for group 0,
group 0+
● Duo Plus for group I
Seats, restraints
● Kidfix XP for group II/III
● Graco Junior for group III
Ensure that the child restraint system
to be installed is compatible with the
vehicle type.
Ensure that the mounting location of
the child restraint system within the
vehicle is correct, see following
tables.
Allow children to enter and exit the
vehicle only on the side facing away
from the traffic.
When the child restraint system is not
in use, secure the seat with a seat belt
or remove it from the vehicle.
Note
Do not affix anything on the child
restraint systems and do not cover
them with any other materials.
A child restraint system which has
been subjected to stress in an
accident must be replaced.
57
58
Seats, restraints
Child restraint installation locations
Permissible options for fastening a child restraint system with a three-point seat belt
On front passenger seat
Weight class
activated airbag
deactivated airbag
On rear outboard seats
On rear centre seat
Group 0: up to 10 kg
X
U/L1,2
U/L3
X
Group 0+: up to 13 kg
X
U/L1,2
U/L3
X
Group I: 9 to 18 kg
X
U/L1,2
U/L3,4
X
Group II: 15 to 25 kg
U/L1,2
X
U/L3,4
X
Group III: 22 to 36 kg
U/L1,2
X
U/L3,4
X
U : universal suitability in conjunction with three-point seat belt
L : suitable for particular child restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories. The
child restraint system must be approved for the specific vehicle type (refer to the vehicle type list of the child restraint
system)
X : no child restraint system permitted in this weight class
1 : move seat forwards as far as necessary and adjust seat backrest inclination as far as necessary to a vertical position
to ensure that the belt runs forwards from the upper anchorage point
2 : move seat height adjustment upwards as far as necessary,
adjust seat backrest inclination as far as necessary to a vertical position to ensure that the belt is tight on the buckle
side
3 : move the respective front seat ahead of the child restraint system forwards and the sliding rear seat backwards as
far as necessary
4 : adjust the respective headrest as necessary or remove if required
Seats, restraints
59
Permissible options for fitting an ISOFIX child restraint system with ISOFIX brackets
On front passenger seat
Weight class
Size class Fixture
On rear outboard
activated airbag deactivated airbag seats
On rear centre
seat
Group 0: up to 10 kg
G
ISO/L2
X
X
X
X
F
ISO/L1
X
X
X
X
E
ISO/R1 X
X
IL1
X
Group 0+: up to 13 kg E
ISO/R1 X
X
IL1
X
D
ISO/R2 X
X
IL1
X
C
ISO/R3 X
X
IL1
X
D
ISO/R2 X
X
IL1,2
X
C
ISO/R3 X
X
IL1,2
X
B
ISO/F2
X
B1
A
Group I: 9 to 18 kg
X
IL,
IUF1,2
X
ISO/F2X X
X
IL, IUF1,2
X
ISO/F3
X
X
IL, IUF1,2
X
Group II: 15 to 25 kg
X
X
IL1,2
X
Group III: 22 to 36 kg
X
X
IL1,2
X
60
Seats, restraints
IL
: suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories.
The ISOFIX restraint system must be approved for the specific vehicle type (refer to the vehicle type list of the child
restraint system)
IUF : suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight class
X : no ISOFIX child restraint system approved in this weight class
1
: move the respective front seat ahead of the child restraint system forwards and the sliding rear seat backwards as
far as necessary
2
: adjust the respective headrest as necessary or remove if required
ISOFIX size class and seat device
A – ISO/F3
: forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg
B – ISO/F2
: forward-facing child restraint system for smaller children in the weight class 9 to 18 kg
B1 – ISO/F2X : forward-facing child restraint system for smaller children in the weight class 9 to 18 kg
C – ISO/R3
: rear-facing child restraint system for children of maximum size in the weight class up to 18 kg
D – ISO/R2
: rear-facing child restraint system for smaller children in the weight class up to 18 kg
E – ISO/R1
: rear-facing child restraint system for young children in the weight class up to 13 kg
F– ISO/L1
: left lateral facing position child restraint system (carry-cot)
G – ISO/L2
: right lateral facing position child restraint system (carry-cot)
Permissible options for fitting an i-Size child restraint system with ISOFIX brackets
On front passenger seat
i-Size child restraint systems
activated airbag
deactivated airbag
On rear outboard seats
On rear centre seat
X
X
i-U
X
i - U : suitable for i-Size 'universal' forward and rearward facing child restraint systems
X
: seating position not suitable for i-Size 'universal' child restraint systems
Storage
Storage
Storage compartments ................ 61
Glovebox ................................... 61
Cupholders ................................ 61
Centre console storage ............. 62
Load compartment ....................... 62
Load compartment cover ........... 64
Rear floor storage cover ............ 64
Lashing eyes ............................. 65
Warning triangle ........................ 66
First aid kit ................................. 66
Roof rack system ......................... 67
Roof rack ................................... 67
Loading information ..................... 67
Storage compartments
9 Warning
Do not store heavy or sharp
objects in the storage
compartments. Otherwise, the
storage compartment lid could
open and vehicle occupants could
be injured by objects being thrown
around in the event of hard
braking, a sudden change in
direction or an accident.
61
The glovebox should be closed whilst
driving.
Cooled glovebox
Air ventilation and temperature
depend on the settings of the climate
control system. The air vent in the
glovebox can be closed 3 118.
Cupholders
Glovebox
Cupholders are located in the centre
console.
62
Storage
Centre console storage
The storage container can be used to
store small items.
Load compartment
The rear seat backrest is divided in
two parts. Both parts can be folded
down.
9 Warning
When folding up, ensure that
backrests are securely locked in
position before driving. Failure to
do so may result in personal injury
or damage to the load or vehicle in
the event of hard braking or a
collision.
Depending on the version, the
storage compartment is located
under a cover.
Before folding rear seat backrests,
execute the following if necessary:
● Remove the load compartment
cover 3 64.
● Press and hold the catch to push
the head restraints down 3 40.
●
Insert the seat belts in the guiding
latches.
Load compartment extension
(version with lever)
Storage
●
●
Pull the lever on one or both outer
sides and fold down the
backrests onto the seat cushion.
To fold up, raise the backrests
and guide them into an upright
position until they engage
audibly.
●
Fold up rear armrest before
folding down the relevant part of
the backrest. Otherwise this part
of the backrest cannot be folded
down.
Folding rear armrest
Pull the loop to fold down the rear
armrest.
●
The backrests are properly
engaged when the red mark near
the lever is no longer visible.
Load compartment extension
(version with loop)
●
Move both rear seats to the most
rearward position 3 45.
●
Pull the loop and fold down the
backrest onto the seat cushion.
To fold up, raise the backrests
and guide them into an upright
position until they engage
audibly.
63
64
Storage
The armrest can also be folded down
from the load compartment by pulling
the loop and pushing the centre
backrest.
The centre backrest is properly
engaged when the red mark on the
loop is no longer visible.
The load compartment cover can be
stored behind the rear seat backrests.
Unhook retaining straps and lift the
cover backwards until it unlatches.
Then slide it down in the guides
behind the seat backrests.
Fitting cover
Load compartment cover
Engage cover in side guides and fold
downwards. Attach the retaining
straps to the tailgate.
Do not place any objects on the cover.
Removing cover
Lift cover, slightly angle and turn it.
Remove the cover.
Rear floor storage cover
Stowing
Unhook retaining straps from tailgate.
Raise cover at the recess to gain
access to emergency breakdown
equipment.
Storage
65
Lashing eyes
Tyre repair kit 3 199.
Spare wheel 3 203.
Double load floor
The double load floor can be inserted
in the load compartment in two
positions:
●
●
lower position above the rear
floor storage cover
upper position interlocked with
the grab handle into back panel
trim
To remove, press the handle to
unlock the load floor and lift it up while
using the handle.
If mounted in the upper position, the
space between the load floor and the
spare wheel well cover can be used
as a storage compartment.
In this position, if the rear seat
backrests are folded forwards, an
almost completely flat load bay is
created.
In the upper position, the double load
floor is able to withstand a maximum
load of 100 kg. In the lower position,
the double load floor is able to
withstand the maximum permissible
load.
The lashing eyes are designed to
secure items against slippage, e.g.
using lashing straps or luggage net.
66
Storage
Warning triangle
First aid kit
Stow the warning triangle in the space
at the rear of the load compartment
and secure it with the Velcro®
fastener.
Fold down the cover on the left side
of the load compartment.
Stow the first aid kit in the stowage
compartment.
Storage
Roof rack system
Roof rack
Detach the cover from each mounting
point and fasten the roof rack with the
attached screws.
67
Loading information
For safety reasons and to avoid
damage to the roof, the vehicleapproved roof rack system is
recommended.
Follow the installation instructions
and remove the roof rack when not in
use.
Mounting roof rack
●
●
Open all doors.
Mounting points are located in each
door frame of the vehicle body.
●
Heavy objects in the load
compartment should be placed
against the seat backrests. Make
sure that the backrests are
securely engaged 3 62. If objects
can be stacked, heavier objects
should be placed at the bottom.
Prevent sliding of loose objects
by securing them with straps
attached to the lashing eyes
3 65.
Do not allow the load to protrude
above the upper edge of the
backrests.
68
●
●
●
Storage
Do not place any objects on the
load compartment cover or the
instrument panel, and do not
cover the sensor on top of the
instrument panel.
The load must not obstruct the
operation of the pedals, parking
brake and gear selector, or
hinder the freedom of movement
of the driver. Do not place any
unsecured objects in the interior.
Do not drive with an open load
compartment.
9 Warning
Always make sure that the load in
the vehicle is securely stowed.
Otherwise objects can be thrown
around inside the vehicle and
cause personal injury or damage
to the load or car.
●
The payload is the difference
between the permitted gross
vehicle weight (see identification
plate 3 221) and the EC kerb
weight, refer to the EEC
Certificate of Conformity
provided with your vehicle or
●
other national registration
documents.
To calculate the payload, enter
the data for your vehicle in the
weights table at the front of this
manual.
The EC kerb weight includes
weights for the driver (68 kg),
luggage (7 kg) and all fluids (fuel
tank 90% full).
Optional equipment and
accessories increase the kerb
weight.
Driving with a roof load increases
the sensitivity of the vehicle to
cross-winds and has a
detrimental effect on vehicle
handling due to the vehicle's
higher centre of gravity.
Distribute the load evenly and
secure it properly with retaining
straps. Adjust the tyre pressure
and vehicle speed according to
the load conditions. Check and
retighten the straps frequently.
Do not drive faster than
120 km/h.
The permissible roof load is
60 kg. The roof load is the
combined weight of the roof rack
and the load.
Instruments and controls
Instruments and
controls
Controls ....................................... 70
Steering wheel adjustment ........ 70
Steering wheel controls ............. 70
Heated steering wheel ............... 70
Horn ........................................... 71
Windscreen wiper and washer . . 71
Rear window wiper and
washer ...................................... 73
Outside temperature .................. 73
Clock ......................................... 74
Power outlets ............................. 74
Inductive charging ..................... 75
Cigarette lighter ......................... 76
Ashtrays .................................... 76
Warning lights, gauges and indi‐
cators ........................................... 76
Instrument cluster ...................... 76
Speedometer ............................. 77
Odometer .................................. 78
Trip odometer ............................ 78
Tachometer ............................... 78
Fuel gauge ................................ 79
Engine coolant temperature
gauge ....................................... 79
Engine oil level monitor ............. 79
Service display .......................... 80
Control indicators ...................... 81
Turn lights .................................. 81
Seat belt reminder ..................... 81
Airbag and belt tensioners ......... 82
Airbag deactivation .................... 82
Charging system ....................... 82
Malfunction indicator light .......... 82
Service vehicle soon ................. 83
Stop engine ............................... 83
System check ............................ 83
Brake and clutch system ........... 83
Parking brake ............................ 83
Antilock brake system (ABS) ..... 84
Gear shifting .............................. 84
Lane departure warning ............ 84
Electronic Stability Control and
Traction Control system ........... 84
Electronic Stability Control and
Traction Control system off ...... 85
Engine coolant temperature ...... 85
Preheating ................................. 85
Exhaust filter .............................. 85
AdBlue ....................................... 85
Deflation detection system ........ 85
Engine oil pressure .................... 85
Low fuel ..................................... 86
Autostop .................................... 86
Exterior light .............................. 86
69
Low beam .................................. 86
High beam ................................. 86
High beam assist ....................... 86
Front fog lights ........................... 86
Rear fog light ............................. 87
Rain sensor ............................... 87
Cruise control ............................ 87
Side blind spot alert ................... 87
Active emergency braking ......... 87
Speed limiter ............................. 87
Door open .................................. 87
Displays ....................................... 88
Driver Information Centre .......... 88
Info Display ................................ 90
Head-up display ........................ 92
Vehicle messages ........................ 94
Warning chimes ......................... 94
Vehicle personalisation ................ 95
Telematics services ..................... 98
Opel Connect ............................ 98
Vauxhall Connect ...................... 98
70
Instruments and controls
Controls
Steering wheel controls
Heated steering wheel
Cruise control and speed limiter are
operated via the controls on the left
side of the steering wheel.
On the same side is located the
switch for the heated steering wheel.
Infotainment system can be operated
via the controls on the right side of the
steering wheel.
Driver assistance systems 3 140.
Further information is available in the
Infotainment manual.
Heated steering wheel 3 70.
Activate heating by pressing *.
Activation is indicated by the LED in
the button.
Heating is operational when the
engine is running and during an
Autostop.
Stop-start system 3 126.
Steering wheel adjustment
Unlock lever, adjust steering wheel,
then engage lever and ensure it is
fully locked.
Do not adjust steering wheel unless
vehicle is stationary and steering
wheel lock has been released.
Instruments and controls
Horn
Windscreen wiper and
washer
Windscreen wiper with adjustable
wiper interval
71
To activate interval wiping mode the
next time ignition is switched on,
press the lever downwards to position
OFF and back to INT.
Adjustable wiper interval
Press j.
HI
LO
INT
OFF
1x
:
:
:
:
:
fast
slow
interval wiping
off
single wipe
Do not use if the windscreen is frozen.
Switch off in car washes.
Wiper lever in position INT.
Turn the adjuster wheel to adjust the
wiping frequency.
72
Instruments and controls
Windscreen wiper with rain
sensor
switched on, press the lever
downwards to position OFF and back
to AUTO.
Do not use if the windscreen is frozen.
Switch off in car washes.
Windscreen washer
Adjustable sensitivity of the rain
sensor
HI
: fast
LO
: slow
AUTO : automatic wiping with rain
sensor
OFF : off
1x
: single wipe
In AUTO position, the rain sensor
detects the amount of water on the
windscreen and automatically
regulates the frequency of the
windscreen wiper. If ignition is
switched off, automatic wiping mode
is deactivated. To activate automatic
wiping mode the next time ignition is
Pull lever. Washer fluid is sprayed
onto the windscreen and the wiper
wipes a few times.
Washer fluid 3 178.
Wiper lever in position AUTO.
Turn the adjuster wheel to adjust the
sensitivity of the rain sensor.
Make sure the sensor is not blocked
3 35, 3 10.
Control indicator < 3 71.
Instruments and controls
Rear window wiper and
washer
Activation or deactivation of this
function can be changed in the
Vehicle personalisation menu 3 95.
Rear window wiper
Rear window washer
OFF : off
INT : intermittent operation
ON : continuous operation
Push lever.
Washer fluid is sprayed onto the rear
window and the wiper wipes a few
times.
The rear window washer system is
deactivated when the fluid level is
low.
Washer fluid 3 178.
Do not use if the rear window is
frozen.
Switch off in car washes.
The rear window wiper comes on
automatically when the windscreen
wiper is switched on and reverse gear
is engaged.
73
Outside temperature
A drop in temperature is indicated
immediately and a rise in temperature
after a time delay.
Illustration shows an example.
If outside temperature drops to 3 °C,
a warning message is displayed in the
Driver Information Centre.
9 Warning
The road surface may already be
icy even though the display
indicates a few degrees above
0 °C.
74
Instruments and controls
Clock
Do not damage the outlets by using
unsuitable plugs.
Stop-start system 3 126.
Date and time are shown in the
Info Display 3 90.
Setting date and time, see
Infotainment manual.
USB charging port
Power outlets
A 12 V power outlet is located in the
centre console.
Another power outlet is located in the
console between the front seats.
Do not exceed the maximum power
consumption of 120 W.
With ignition off, the power outlet is
deactivated. Additionally, the power
outlet is deactivated in the event of
low vehicle battery voltage.
Electrical accessories that are
connected must comply with the
electromagnetic compatibility
requirements laid down in
DIN VDE 40 839.
Do not connect any current-delivering
accessories, e.g. electrical charging
devices or batteries.
One or two USB ports are prepared
for charging devices.
When two USB ports are available,
the upper USB port can be used to
connect a phone for phone projection.
Note
The sockets must always be kept
clean and dry.
USB port and phone projection see
Infotainment manual.
Instruments and controls
Inductive charging
9 Warning
Inductive charging can affect the
operation of implanted
pacemakers or other medical
devices. If applicable, seek
medical advice before using the
inductive charging device.
9 Warning
Remove any metal objects from
the charging device before
charging a mobile device, as these
objects could become very hot.
To charge a mobile device:
1. Remove all objects from the
charging device.
2. Place the mobile device with the
display facing upwards on the
charging device.
3. LED illuminates green, when
mobile device is charging.
The mobile device must be smaller
than 7 cm by 15 cm to fit into the
charging device.
PMA or Qi compatible mobile devices
can be charged inductively.
75
On some mobile devices, a back
cover with an integrated coil or a
jacket may be required to use
inductive charging.
Protective cover for the mobile device
could have impact on the inductive
charging.
LED illuminates yellow, when
● metall objects have been
detected in the charging area
● mobile device was not placed
properly.
In the case that the mobile device is
not charging properly:
1. Remove the mobile device from
the charging device.
2. Rotate the mobile device by 180°.
3. Wait 3 seconds after the LED has
extinguished and place the mobile
device on the charging device
again.
76
Instruments and controls
Warning lights, gauges
and indicators
Cigarette lighter
Instrument cluster
Press in the cigarette lighter. It
switches off automatically once the
element is glowing. Pull out the
cigarette lighter.
A portable ashtray can be placed in
the cupholders.
Overview
O
Turn lights 3 81
X
Seat belt reminder 3 81
v
Airbag and belt tensioners
3 82
Caution
V
Airbag deactivation 3 82
To be used only for ash and not for
combustible rubbish.
p
Charging system 3 82
Z
Malfunction indicator light
3 82
C
Service vehicle soon 3 83
Ashtrays
Instruments and controls
STOP Stop engine 3 83
J
System check 3 83
R
Brake and clutch system
3 83
m
Parking brake3 83
u
Antilock brake system (ABS)
3 84
R
)
w
Deflation detection system
3 85
I
Engine oil pressure 3 85
Engine oil level monitor
3 79
Yo
Low fuel 3 86
D
Autostop 3 86
Gear shifting 3 84
8
Exterior light 3 86
Lane departure warning
3 84
9
Low beam 3 86
C
High beam 3 86
Electronic Stability Control
and Traction Control system
3 84
f
High beam assist 3 86
>
Front fog lights 3 86
Electronic Stability Control
and Traction Control system
off 3 85
ø
Rear fog light 3 87
<
Rain sensor 3 87
Engine coolant temperature
high 3 85
m
Cruise control 3 87
B
Side blind spot alert 3 87
!
Preheating 3 85
Ø
%
Exhaust filter 3 85
Active emergency braking
3 87
Y
AdBlue 3 85
b
a
Wo
ß
Speed limiter 3 87
h
Door open 3 87
Speedometer
Indicates vehicle speed.
77
78
Instruments and controls
Odometer
Tachometer
Monochrome display
The total recorded distance is
displayed in km.
Trip odometer
The recorded distance since the last
reset is displayed in the Driver
Information Centre.
Trip odometer counts up to
9,999.9 km without automatic reset.
Press L for 2 seconds to reset trip
odometer.
Colour display
Trip odometer counts up to
1,999.9 km and resets then
automatically.
Press L for 2 seconds to reset trip
odometer.
The trip / fuel information menu
provides additionally two trip counter
3 88.
Displays the engine speed.
Drive in a low engine speed range for
each gear as much as possible.
A red marker indicates the beginning
of the warning zone of excessive
revolutions. For Diesel engines, the
warning zone starts at 5000
revolutions per minute. For petrol
engines, the warning zone starts at
7000 revolutions per minute.
Instruments and controls
Caution
If the needle is in the red warning
zone, the maximum permitted
engine speed is exceeded. Engine
at risk.
Engine coolant temperature
gauge
Fuel gauge
Caution
If engine coolant temperature is
too high, stop vehicle, switch off
engine. Danger to engine. Check
coolant level.
Engine oil level monitor
Displays the coolant temperature.
50 : engine operating temperature
not yet reached
90 : normal operating temperature
130 : temperature too high
Displays the fuel level in the tank.
Control indicator o illuminates if the
level in the tank is low.
Never run the fuel tank dry.
Because of the fuel remaining in the
tank, the top-up quantity may be less
than the specified fuel tank capacity.
79
Control indicator o illuminates if
engine coolant temperature is too
high.
The state of the engine oil level is
displayed in the Driver Information
Centre for a few seconds following
the service information after switching
on the ignition.
A proper state of engine oil level is
indicated by the message Oil level
correct.
If engine oil level is low, I flashes
and Oil level incorrect is indicated,
accompanied by the C indicator.
Confirm engine oil level by using the
dipstick and top up engine oil
respectively.
Engine oil 3 177.
A fault of measurement is indicated
by the message Oil level
measurement invalid. Check engine
oil level manually by using the
dipstick.
80
Instruments and controls
Service display
The service system informs when to
change the engine oil and filter or a
vehicle service is required. Based on
driving conditions, the interval at
which an engine oil and filter change
is required can vary considerably.
Service information 3 215.
A required service due is displayed in
the Driver Information Centre for
7 seconds after switching on the
ignition.
If no service is required for the next
3000 km or more no service
information appears in the display.
If service is required within the next
3000 km, the remaining distance or
time duration is indicated for several
seconds. Simultaneously symbol
C lights up permanently as
reminder.
If service is required in less than
1000 km, C flashes and then lights
up permanently. Remaining distance
or time duration is indicated for
several seconds.
Overdued service is indicated by a
message in the Driver Information
Centre which indicates the overdued
distance. C flashes and then lights
up permanently until service is
executed.
Retrieving service information
To retrieve the status of the service
information at any time press left
button underneath the Driver
Information Centre.
Reset of service interval
After each service, the service
indicator must be reset to ensure
proper functionality. It is
recommended to seek the assistance
of a workshop.
Operate as following:
● switch off ignition
● press and hold button M or
CHECK
● switch on ignition, the distance
indication begins a countdown
● when the display indicates =0,
release the button
The C disappears.
Or
Instruments and controls
The control indicator colours mean:
red
: danger, important reminder
yellow : warning, information, fault
green : confirmation of activation
blue : confirmation of activation
white : confirmation of activation
Instrument cluster overview 3 76.
81
Seat belt reminder
Seat belt reminder on all seats
X illuminates or flashes red in the
instrument cluster together with the
indication in the roof console for each
seat belt.
Turn lights
O illuminates or flashes green.
The service information is displayed
for a few seconds.
Service information 3 215.
Illuminates briefly
Control indicators
A turn light or the hazard warning
flashers are activated.
Rapid flashing: failure of a turn light or
associated fuse.
This includes turn lights connected to
the socket of the towing equipment.
Bulb replacement 3 182.
Fuses 3 190.
Turn lights 3 104.
The control indicators described are
not present in all vehicles. The
description applies to all instrument
versions.
Depending on the equipment, the
position of the control indicators may
vary. When the ignition is switched
on, most control indicators will
illuminate briefly as a functionality
test.
The parking lights are switched on.
Flashes
●
When the ignition is switched on,
X in the instrument cluster and
the symbol for the respective
seat in the roof console comes
82
Instruments and controls
on, if the seat belt of any
occupied seat has not been
fastened.
● After driving off, X in the
instrument cluster and the
symbol for the respective seat in
the roof console flashes for a
certain time together with a
chime. After a certain time of
driving X illuminates constantly
until the seat belt of the
respective seat has been
fastened or if any passenger has
unfastened the seat belt.
Seat belts 3 46.
Deployment of the belt pretensioners
or airbags is indicated by continuous
illumination of v.
9 Warning
Have the cause of the fault
remedied immediately by a
workshop.
Belt pretensioners 3 46.
Airbag system 3 49.
Airbag deactivation
Airbag and belt tensioners
v illuminates red.
When the ignition is switched on, the
control indicator illuminates for
approx. 4 seconds. If it does not
illuminate, does not go out after
4 seconds or illuminates whilst
driving, there is a fault in the airbag
system. Seek the assistance of a
workshop. The airbags and belt
pretensioners may fail to trigger in the
event of an accident.
The front passenger airbag is
activated.
*OFF illuminates yellow.
The front passenger airbag is
deactivated.
Airbag deactivation 3 54.
Charging system
p illuminates red.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
Illuminates when the engine is
running
Stop, switch off engine. Vehicle
battery is not charging. Engine
cooling may be interrupted. The
brake servo unit may cease to be
effective. Seek the assistance of a
workshop.
Malfunction indicator light
Z illuminates or flashes yellow.
ÓON illuminates yellow.
Instruments and controls
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
Illuminates when the engine is
running
Fault in the emission control system.
The permitted emission limits may be
exceeded.
Seek the assistance of a workshop
immediately.
Flashes when the engine is
running
The engine management system has
a fault that could lead to catalytic
converter damage. Ease up on the
accelerator until the flashing stops.
Seek the assistance of a workshop
immediately.
Service vehicle soon
C illuminates yellow.
Illuminates briefly when the ignition is
switched on.
May illuminate together with other
control indicators and a
corresponding message in the Driver
Information Centre.
Seek the assistance of a workshop
immediately.
Illuminates red
Stop engine
Brake and clutch system
Y illuminates red.
Illuminates briefly when the ignition is
switched on.
Illuminates together with other control
indicators, accompanied by a warning
chime and a corresponding message
in the Driver Information Centre.
Stop engine immediately and seek
the assistance of a workshop.
System check
J illuminates yellow or red.
Illuminates yellow
A minor engine fault has been
detected.
83
A major engine fault has been
detected.
Stop engine as soon as possible and
seek the assistance of a workshop.
R illuminates red.
The brake and clutch fluid level is too
low, when parking brake is not
applied 3 179.
9 Warning
Stop. Do not continue your
journey. Consult a workshop.
Illuminates when the manual parking
brake is applied and ignition is
switched on 3 138.
Brake fluid 3 179.
Parking brake
m illuminates red.
84
Instruments and controls
Illuminates when the parking brake is
applied and ignition is switched on
3 138.
Gear shifting
Lane departure warning
Manual transmission
) flashes yellow when the system
recognises an unintended lane
change.
Lane departure warning 3 163.
Antilock brake system
(ABS)
u illuminates yellow.
Illuminates for a few seconds after the
ignition is switched on. The system is
ready for operation when the control
indicator extinguishes.
If the control indicator does not go out
after a few seconds, or if it illuminates
while driving, there is a fault in the
ABS. The brake system remains
operational but without ABS
regulation.
Antilock brake system 3 137.
Electronic Stability Control
and Traction Control system
b illuminates or flashes yellow.
Illuminates
R with the number of a higher gear is
indicated, when upshifting into this
gear is recommended for fuel saving
reasons.
Automatic transmission manual
mode
R is indicated, when upshifting is
recommended for fuel saving
reasons.
A fault in the system is present.
Continued driving is possible. Driving
stability, however, may deteriorate
depending on road surface
conditions.
Have the cause of the fault remedied
by a workshop.
Flashes
The system is actively engaged.
Engine output may be reduced and
the vehicle may be braked
automatically to a small degree.
Electronic Stability Control and
Traction Control system 3 139.
Instruments and controls
Electronic Stability Control
and Traction Control system
off
n illuminates yellow.
The systems are deactivated.
Preheating of diesel engine is
activated. Only activates when
outside temperature is low. Start the
engine when control indicator
extinguishes.
Starting the engine 3 124.
Engine coolant temperature
Exhaust filter
o illuminates red.
Illuminates when the engine is
running
Stop, switch off engine.
Caution
Coolant temperature too high.
Check coolant level immediately
3 178.
If there is sufficient coolant, consult a
workshop.
Preheating
! illuminates yellow.
% or C illuminates yellow.
The exhaust filter requires cleaning.
Continue driving until the control
indicator extinguishes.
Illuminates temporarily
Start of saturation of the exhaust filter.
Start cleaning process as soon as
possible by driving at a vehicle speed
of at least 60 km/h.
Illuminates constantly
Indication of a low additive level. Seek
the assistance of a workshop.
Exhaust filter 3 129.
AdBlue
Y flashes or illuminates yellow.
85
Illuminates yellow
The remaining driving range is
between 600 km and 2400 km.
Flashes yellow
The remaining driving range is
between 0 and 600 km.
AdBlue level is low. Refill AdBlue
soon to avoid prevention of the
engine start.
AdBlue 3 130.
Deflation detection system
w illuminates or flashes yellow.
Illuminates
Tyre pressure loss in one or more
wheels. Stop immediately and check
tyre pressure.
Flashes
Fault in system. Consult a workshop.
Deflation detection system 3 197.
Engine oil pressure
I illuminates red.
86
Instruments and controls
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
Illuminates when the engine is
running
Caution
Engine lubrication may be
interrupted. This may result in
damage to the engine and / or
locking of the drive wheels.
1. Select neutral gear.
2. Move out of the flow of traffic as
quickly as possible without
impeding other vehicles.
3. Switch off ignition.
9 Warning
When the engine is off,
considerably more force is needed
to brake and steer.
During an Autostop, the brake
servo unit will still be operational.
Do not remove key until vehicle is
stationary, otherwise the steering
wheel lock could engage
unexpectedly.
Keep engine turned off and let the
vehicle be towed to a workshop
3 177.
Low fuel
Stop-start system 3 126.
Exterior light
8 illuminates green.
The exterior lights are on 3 100.
Low beam
9 illuminates green.
Illuminated when low beam is on.
o illuminates yellow.
Level in fuel tank is too low.
Refuelling 3 167.
Bleeding the diesel fuel system
3 181.
C illuminates blue.
Illuminated when high beam is on or
during headlight flash 3 101.
Autostop
High beam assist
D illuminates or flashes green.
Illuminates green
Engine is in an Autostop.
High beam
f illuminates green.
The high beam assist is activated
3 101.
Flashes green
Front fog lights
Autostop is temporarily unavailable,
or Autostop mode is invoked
automatically.
> illuminates green.
The front fog lights are on 3 104.
Instruments and controls
Rear fog light
Illuminates
ø illuminates yellow.
The rear fog light is on 3 105.
The system has been deactivated or
a fault has been detected.
Additionally, a warning message is
displayed in the Driver Information
Centre.
Check the reason of the deactivation
3 147 and in case of a system fault,
seek the assistance of a workshop.
Rain sensor
< illuminates green.
Illuminated when automatic wiping
with rain sensor is activated.
Windscreen wiper and washer 3 71.
Cruise control
m illuminates in the Driver
Information Centre.
Cruise control 3 140.
Side blind spot alert
B illuminates green.
The system is active 3 158.
Active emergency braking
m illuminates or flashes yellow.
Note
m also illuminates if the seat belts
of the front passengers are not
fastened. In this case, active
emergency braking is deactivated.
Flashes
The system is actively engaged.
Depending on the situation, the
vehicle may automatically brake
moderately or hard.
Forward collision alert 3 145.
Front pedestrian protection 3 149.
Speed limiter
ß illuminates in the Driver
Information Centre.
Speed limiter 3 143.
Door open
h illuminates red.
A door or the tailgate is open.
87
88
Instruments and controls
Displays
Selecting menus and functions
Driver Information Centre
The Driver Information Centre is
located in the instrument cluster.
Depending on the version, the Driver
Information Centre is available as
monochrome or colour display.
Driver Information Centre indicates:
● overall and trip odometer
● digital speed indication
● trip / fuel information menu
● gear shift indication
● service information
● vehicle and warning messages
● driver assistance messages
● pop-up messages
● AdBlue information
Turn the adjuster wheel to select a
page in the trip / fuel information
menu.
Press SET/CLR to confirm or reset a
function.
Vehicle and service messages are
popped up in the Driver Information
Centre if required. Scroll messages
by turning the adjuster wheel.
Confirm messages by pressing
SET/CLR.
Additionally, some menus can be
selected via the left button:
Press M to switch between the
respective menus.
Or
Instruments and controls
Press CHECK to switch between the
respective menus.
Vehicle messages 3 94.
Trip / fuel information menu,
monochrome display
Average fuel consumption
Display of average consumption. The
measurement can be reset at any
time and starts with a default value.
To reset, press SET/CLR for a few
seconds.
89
Digital speed
Digital display of the instantaneous
speed.
Trip / fuel information menu,
colour display
Average speed
Display of average speed. The
measurement can be reset at any
time.
To reset, press SET/CLR for a few
seconds.
Turn the adjuster wheel to select a
page:
Trip odometer
Trip odometer 3 78.
Fuel range
Range is calculated from current fuel
level and current consumption. The
display shows average values.
After refuelling, the range is updated
automatically after a brief delay.
When the fuel level is low, a message
appears on the display and the
control indicator o in the fuel gauge
illuminates 3 86.
Instantaneous Fuel Consumption
Display of the instantaneous
consumption.
Differerent pages with combined
information can be selected.
Turn the adjuster wheel to select a
page.
Information page:
Fuel range
Range is calculated from current fuel
level and current consumption. The
display shows average values.
90
Instruments and controls
After refuelling, the range is updated
automatically after a brief delay.
When the fuel level is low, a message
appears on the display and the
control indicator o in the fuel gauge
illuminates 3 86.
Instantaneous Fuel Consumption
Display of the instantaneous
consumption.
Trip 1 page:
Average speed
Display of average speed. The
measurement can be reset at any
time.
Average fuel consumption
Display of average consumption. The
measurement can be reset at any
time and starts with a default value.
Distance travelled
Displays the current distance for trip
1 since the reset.
Trip odometer counts up to
9,999.9 km without automatic reset.
The values of trip 1 page can be reset
by pressing SET/CLR for a few
seconds.
Trip 2 page:
Average speed
Display of average speed. The
measurement can be reset at any
time.
Average fuel consumption
Display of average consumption. The
measurement can be reset at any
time and starts with a default value.
Distance travelled
Displays the current distance for trip
2 since a certain reset.
The values of trip 2 page can be reset
by pressing SET/CLR for a few
seconds.
Digital speed page
Digital display of the instantaneous
speed.
Stop and Start time counter
A time counter calculates the time
spent in STOP mode during a
journey. It resets to zero every time
the ignition is switched on.
Compass page
Displays the geographic direction of
driving.
Blank page
No trip/fuel information is displayed.
AdBlue
Press M or CHECK repeatedly until
the AdBlue menu is shown.
AdBlue range
Indicates an estimate of the AdBlue
level. A message indicates whether
the level is sufficient or low.
3 130.
Info Display
The Info Display is located in the
instrument panel near the instrument
cluster.
Depending on the vehicle
configuration the vehicle has a
● Graphic Info Display
or
● 7'' Colour Info Display with
touchscreen functionality
or
● 8'' Colour Info Display with
touchscreen functionality
Instruments and controls
The Info Display can indicate:
● time 3 74
● outside temperature 3 73
● date 3 74
● Infotainment system, see
description in the Infotainment
manual
● indication of rear view camera
3 162
● indication of panoramic view
system 3 159
● indication of parking assist
instructions 3 150
● navigation, see description in the
Infotainment manual
● vehicle and system messages
3 94
● settings for vehicle
personalisation 3 95
91
Graphic Info Display
Press X to switch on the display.
Press MENU to select main menu
page.
Press èäåé to select a menu page.
Press OK to confirm a selection.
Press BACK to exit a menu without
changing a setting.
For further information, see
Infotainment manual.
7'' Colour Info Display
Selecting menus and settings
Menus and settings are accessed via
the touchscreen.
Press X to switch on the display.
Press ; to display the homepage.
Touch required menu display icon.
Touch a respective icon to confirm a
selection.
Touch 9 to return to the next higher
menu level.
Press ; to return to the homepage.
For further information, see
Infotainment manual.
Vehicle personalisation 3 95.
92
Instruments and controls
8'' Colour Info Display
Selecting menus and settings
There are three options to operate the
display:
● via buttons below the display
● by touching the touchscreen
● via speech recognition
Button and touch operation
Touch required menu display icon or
a function.
Confirm a required function or
selection by touching.
Touch r on the display to exit a
menu without changing a setting.
For further information, see
Infotainment manual.
Speech recognition
Description see Infotainment manual.
Vehicle personalisation 3 95.
Head-up display
Press X to switch on the display.
Press SET to select system settings
(units, language, time and date).
Press Í to select vehicle settings or
driving functions.
The head-up display displays driver
information onto a foldable projection
plane on the driver's side.
The information appears as an image
projected from a lense in the
instrument panel onto the projection
plane directly ahead in driver's view.
The image appears focused out
toward the front of the vehicle.
Head-up display views:
● vehicle speed
● speed limits by the traffic sign
recognition
● set speed of speed limiter
● set speed of cruise control
● navigation information.
Instruments and controls
keep the head-up display image
dim and placed low in your field of
view.
Adjust brightness
Adjust position of head-up display
image
1. Adjust the driver's seat.
2. Start the engine.
3. Press ä or å to centre the image.
It can only be adjusted up and
down, not side to side.
9 Warning
If the head-up display image is too
bright or too high in your field of
view, it may obstruct your view
when it is dark outside. Be sure to
The head-up display image will
automatically dim and brighten to
compensate for outside lighting.
Brightness can also be adjusted
manually as needed:
Press e to brighten the display. Press
æ to dim the display.
The image can temporarily light up
depending on angel and position of
sunlight.
Switching off
Press æ and hold to turn the head-up
display off.
Language
Preferred language can be set in
vehicle personalisation menu 3 95.
Units
Units can be changed in vehicle
personalisation menu 3 95.
93
Care of head-up display
Clean the projection plane of the
head-up display with a soft cloth
sprayed with glass cleaner. Wipe the
lens gently, then dry it.
System limitations
Head-up display may not operate
properly when:
● The lens in the instrument panel
is covered by objects or not
clean.
● Display brightness is too dim or
bright.
● Image is not adjusted to the
proper height.
● The driver wears polarised
sunglasses.
If the head-up image is not correct for
other reasons, contact a workshop.
94
Instruments and controls
Vehicle messages
Messages in the
Colour Info Display
Messages are indicated in the Driver
Information Centre, in some cases
together with a warning chime.
Some important messages may
appear additionally in the
Info Display. Some messages only
pop-up for a few seconds.
Warning chimes
If several warnings appear at the
same time, only one warning chime
will sound.
When starting the engine or whilst
driving
Press SET/CLR to confirm a
message.
Vehicle and service messages
The vehicle messages are displayed
as text. Follow the instructions given
in the messages.
The warning chime regarding not
fastened seat belts has priority over
any other warning chime.
● If a seat belt is not fastened.
● If a door or the tailgate is not fully
closed when starting off.
● If a certain speed is exceeded
with parking brake applied.
● If cruise control deactivates
automatically.
● If a programmed speed or speed
limit is exceeded.
●
●
●
●
●
If a warning message appears in
the Driver Information Centre.
If the electronic key is not in the
passenger compartment.
If the parking assist detects an
object.
If an unintended lane change
occurs.
If the exhaust filter has reached
the maximum filling level.
When the vehicle is parked and /
or the driver's door is opened
●
With exterior lights on.
During an Autostop
●
●
If the driver's door is opened.
If any condition for an autostart is
not fulfilled.
Instruments and controls
Vehicle personalisation
The vehicle's behaviour can be
personalised by changing the settings
in the Info Display.
Some functions are only displayed or
active when the engine is running.
Graphic Info Display
Press MENU to open the menu page.
Use four-way button to operate the
display:
Select ˆ Personalisationconfiguration I OK.
Unit settings
Select Display configuration I OK.
Select Choise of units I OK.
Select desired settings I OK.
Language settings
Select Display configuration I OK.
Select Choise of language I OK.
Select desired language I OK.
Vehicle settings
Select Define vehicle parameters I
OK.
In the corresponding submenus the
following settings can be changed:
● Lighting.
Follow me home headlamps:
Activation and setting duration
time.
Welcome lighting: Activation and
setting duration time.
● Comfort
Ambient lighting: Activation /
Deactivation.
Rear wiper in reverse gear:
Activation / Deactivation.
●
●
95
Vehicle
Unlocking boot only: Activation /
Deactivation.
Plip action: Driver / all doors.
Driving assistance
Fatigue Detection system:
Activation / Deactivation.
Speed recommendation:
Activation / Deactivation.
7" Colour Info Display
Press ; to open homepage.
Use touch buttons to operate the
display:
Select Settings.
96
Instruments and controls
Unit settings
Select Units
Change units for Consumption and
Distance and Temperature.
Language settings
Select Language.
Change language by touching the
respective entry.
Vehicle settings
Select Vehicle.
In the corresponding submenus the
following settings can be changed:
● Collision / Detection Systems
Side Blind Spot Alert: Activates
or deactivates side blind spot
alert.
Drowsy Driver Alert : Activates or
deactivates the driver
drowsiness system.
Speed Limit Information:
Activates or deactivates the
speed limit information by traffic
sign recognition.
Rear View Camera Guidelines:
Activates or deactivates the rear
●
●
●
view camera guidelines on the
Info Display.
Comfort and Convenience
Auto Wipe in Reverse Gear:
Activates or deactivates
automatic switching on of the
rear window wiper when reverse
gear is engaged.
Lighting
Ambient Lighting: Activates or
deactivates the ambient lighting
and adjusts its brightness.
Welcome Lighting: Activates or
deactivates and changes the
duration of welcome lighting.
Exit Lighting: Activates or
deactivates and changes the
duration of exit lighting.
Remote Lock, Unlock, Start
Remote Door Unlock: Changes
the configuration to unlock the
driver's door only or all doors
when pressing O on the remote
control.
Unlock boot only: Activates or
deactivates unlocking the tailgate
only when pressing T on the
remote control.
8" Colour Info Display
Press SET to open settings menu.
Use touch buttons to operate the
display.
Unit settings
Select System settings.
Change units for Consumption and
Distance and Temperature.
Confirm with G.
Language settings
Select Languages.
Instruments and controls
Change language by touching the
respective entry.
Confirm with G.
Vehicle settings
●
●
Press Í.
Select Vehicle settings.
In the corresponding submenus the
following settings can be changed:
● Headlights
Welcome lighting: Activates or
deactivates the function and
adjusts its duration.
●
Guide-me-home lighting:
Activates or deactivates the
function and adjusts its duration.
Comfort
Mood lighting: Adjusts the
brightness of the ambient
lighting.
Rear wiper in reverse: Activates
or deactivates automatic
switching on of the rear window
wiper when reverse gear is
engaged.
Vehicle access
Door unlock: boot only: Activates
or deactivates unlocking only the
tailgate when pressing T on the
remote control.
Door unlock: driver only:
Changes the configuration to
unlock only the driver's door and
fuel filler flap or all doors, load
compartment and fuel filler flap
when pressing O on the remote
control.
Safety
Driver attention warning:
Activates or deactivates the
driver drowsiness system.
97
Driving functions
Press Í.
Select Driving functions.
In the corresponding submenus the
following settings can be changed:
● Park Assist: Activates advanced
park assist, a parking maneuver
can be selected.
● Blind Spot Sensors: Activates or
deactivates side blind spot alert.
● Panoramic view system:
Activation / deactivation of the
function.
98
Instruments and controls
Telematics services
Opel Connect
Opel Connect is a new way to stay
connected and secure on the road.
Features available with
Opel Connect are:
● emergency call function
● breakdown call function
When the vehicle is equipped with
Opel Connect, these features are
automatically activated. Terms and
Conditions apply.
Opel Connect is operated by the
buttons in the overhead console.
Note
Opel Connect is not available for all
markets. For further information,
contact your workshop.
Emergency call function
Vehicles featuring the emergency call
function are equipped with a red
SOS button in the overhead console.
The emergency call function will
establish a connection to the nearest
public safety answering point (PSAP).
A minimum set of data including
vehicle and location information will
be sent to the PSAP.
Note
Establishing an emergency call may
not be possible in areas without
sufficient network availability or due
to hardware damage during an
accident.
Automatic crash notification
In case of an accident with airbag
deployment, an automatic
emergency call is established and an
automatic crash notification will be
transmitted to the next public safety
answering point.
Emergency assistance
In case of an emergency you can also
manually place an emergency call by
pressing the red SOS button for more
than two seconds. The LED flashes to
confirm that a connection to the
nearest PSAP is being established.
The LED illuminates steadily as long
as the call is active.
Pressing the SOS button immediately
a second time will terminate the call.
The LED switches off.
Status LED
Illuminates green and red and
extinguishes after a short time, when
the ignition is switched on: the system
works properly.
Illuminates red: fault in the system.
Contact a workshop.
Flashes red: backup battery needs
replacement.
Breakdown call function
Pressing . for more than two
seconds connects you to a roadside
assistance service provider.
For information about coverage and
scope of services of the roadside
assistance, please refer to the
Service and warranty booklet.
Vauxhall Connect
Vauxhall Connect is a new way to
stay connected and secure on the
road.
Features available with
Vauxhall Connect are:
● emergency call function
● breakdown call function
Instruments and controls
When the vehicle is equipped with
Vauxhall Connect, these features are
automatically activated. Terms and
Conditions apply.
Vauxhall Connect is operated by the
buttons in the overhead console.
Emergency call function
Vehicles featuring the emergency call
function are equipped with a red
SOS button in the overhead console.
The emergency call function will
establish a connection to the nearest
public safety answering point (PSAP).
A minimum set of data including
vehicle and location information will
be sent to the PSAP.
Note
Establishing an emergency call may
not be possible in areas without
sufficient network availability or due
to hardware damage during an
accident.
Automatic crash notification
In case of an accident with airbag
deployment, an automatic
emergency call is established and an
automatic crash notification will be
transmitted to the next public safety
answering point.
Emergency assistance
In case of an emergency you can also
manually place an emergency call by
pressing the red SOS button for more
than two seconds. The LED flashes to
confirm that a connection to the
nearest PSAP is being established.
The LED illuminates steadily as long
as the call is active.
Pressing the SOS button immediately
a second time will terminate the call.
The LED switches off.
Status LED
Illuminates green and red and
extinguishes after a short time, when
the ignition is switched on: the system
works properly.
Illuminates red: fault in the system.
Contact a workshop.
Flashes red: backup battery needs
replacement.
99
Breakdown call function
Pressing . for more than two
seconds connects you to a roadside
assistance service provider.
For information about coverage and
scope of services of the roadside
assistance, please refer to the
Service and warranty booklet.
100
Lighting
Lighting
Exterior lighting .......................... 100
Light switch .............................. 100
Automatic light control ............. 101
High beam ............................... 101
High beam assist ..................... 101
Headlight flash ......................... 102
Headlight range adjustment .... 102
Headlights when driving
abroad .................................... 103
Daytime running lights ............. 103
LED headlights ........................ 103
Hazard warning flashers .......... 103
Turn lights ................................ 104
Front fog lights ......................... 104
Rear fog light ........................... 105
Parking lights ........................... 105
Reversing lights ....................... 105
Misted light covers ................... 105
Interior lighting ........................... 106
Instrument panel illumination
control ..................................... 106
Interior lights ............................ 106
Reading lights .......................... 106
Sun visor lights ........................ 107
Lighting features ........................ 107
Centre console lighting ............ 107
Entry lighting ............................ 107
Exit lighting .............................. 107
Battery discharge protection .... 108
Exterior lighting
Light switch
Turn light switch:
AUTO : automatic light control
switches automatically
between daytime running
light and headlight
: sidelights
8
: headlights
9
Control indicator 8 3 86.
Tail lights
Tail lights are illuminated together
with low / high beam and sidelights.
Lighting
Automatic light control
Additionally, headlights are switched
on if the windscreen wipers have
been activated for several wipes.
LED headlights 3 103.
Tunnel detection
When a tunnel is entered headlights
are switched on immediately.
High beam
When the automatic light control
function is switched on and the
engine is running, the system
switches between daytime running
lights and headlights automatically
depending on the external lighting
conditions and information given by
the wiper system.
Make sure the sensor is not blocked
3 10, 3 35.
Daytime running light 3 103.
Automatic headlight activation
During poor lighting conditions
headlights are switched on.
Push to switch from low to high beam.
Pull to deactivate high beam.
High beam assist 3 101.
101
High beam assist
The camera in the windscreen
detects the lights of oncoming or
preceding vehicles. Once activated,
high beam assist remains active and
switches high beam on and off
depending on surrounding
conditions. The latest setting of the
high beam assist will remain after the
ignition is switched on again.
This feature automatically activates
the high beam in the dark when
vehicle speed is faster than 25 km/h.
It switches automatically back to low
beam when:
● The camera in the windscreen
detects the lights of oncoming or
preceding vehicles.
● The vehicle speed drops below
15 km/h.
● It is foggy or snowy.
● Front or rear fog lights are
switched on.
● Driving in urban areas.
If there are no restrictions detected,
the system switches back to high
beam.
102
Lighting
Activation
Activate high beam assist by pressing
f. The LED of the button
illuminates.
The green control indicator f
illuminates continuously when the
high beam assist is activated, the blue
one 7 illuminates when high beam is
on.
Control indicator f 3 86, 7 3 86.
If a headlight flash is activated when
the high beam assist is activated and
low beam is on, the high beam assist
will be deactivated. The system
changes to high beam.
If a headlight flash is activated when
the high beam assist is activated and
high beam is on, the high beam assist
will be deactivated. The system
changes to low beam.
To reactivate the high beam assist,
flash the headlights again.
Pull to deactivate the high beam.
Headlight range adjustment
Manual headlight range
adjustment
Headlight range can be adjusted
manually if vehicle is equipped with
halogen headlights. LED headlights
are adjusted automatically.
Dynamic automatic headlight
levelling 3 103.
Headlight flash
Deactivation
Deactivate high beam assist by
pressing f. The LED of the button
extinguishes.
Pull to activate the headlight flash.
To adapt headlight range to the
vehicle load to prevent dazzling: turn
thumb wheel ? to required position.
Lighting
0 : front seats occupied
1 : all seats occupied
2 : all seats occupied and load
compartment laden
3 : driver's seat occupied and load
compartment laden
Headlights when driving
abroad
When driving in countries where
traffic drives on the opposite side of
the road, the headlights do not have
to be adjusted.
LED headlights
Reverse parking function
LED headlights for low and high beam
ensure better visibility under all
conditions. They include the following
functions:
● cornering lights
● high beam assist 3 101
● automatic headlight levelling
To assist driver's orientation when
parking, both corner lights and
reversing light illuminate when
headlights are on and reverse gear is
engaged. They remain illuminated for
a short time after disengaging reverse
gear or until driving faster than
7 km/h in a forward gear.
Cornering light
Automatic headlight levelling
Light switch must be in position
AUTO.
To prevent oncoming traffic from
being dazzled, headlight levelling is
automatically adjusted.
Daytime running lights
Daytime running lights increases
visibility of the vehicle during daylight.
They are switched on automatically
during daytime when engine is
running.
The system switches between
daytime running lights and low beam
automatically, depending on the
lighting conditions.
103
Fault in LED headlight system
When turning off, depending on the
steering angle and the turn light,
particular LEDs are triggered which
illuminate the direction of travel. It is
activated up to a speed of 40 km/h.
When the system detects a failure in
the LED headlight system, a warning
is displayed in the Driver Information
Centre.
Hazard warning flashers
Operated by pressing ¨.
104
Lighting
Turn lights
Activate temporary flashing by
holding the lever just before the
resistance point. Turn lights will flash
until lever is being released.
To activate three flashes, tap the
lever briefly without passing the
resistance point.
Front fog lights
Hazard warning flashers are switched
on automatically in the following
situations:
● braking in an emergency
(depending on the force of
deceleration)
● in the event of an accident.
They are switched off by pressing ¨
or accelerating.
up
: right turn light
down : left turn light
A resistance point can be felt when
moving the lever.
Constant flashing is activated when
the lever is being moved beyond the
resistance point. It is deactivated
when the steering wheel is moved in
the opposite direction or lever is
manually moved back to its neutral
position.
After 20 seconds the volume of the
audible signal will increase if the
speed is above 60 km/h.
Operated by pressing >.
Light switch in position AUTO:
switching on front fog lights will switch
headlights on automatically.
The fog lights should only be used in
very bad visibility conditions like fog,
snow or heavy rain.
Lighting
Rear fog light
Parking lights
105
Reversing lights
The reversing light comes on when
the ignition is on and reverse gear is
selected.
Misted light covers
The inside of the light housing may
mist up briefly in poor, wet and cold
weather conditions, in heavy rain or
after washing. The mist disappears
quickly by itself. To help, switch on the
headlights.
Operated by pressing ø.
Light switch in position AUTO:
switching on rear fog light will switch
headlights on automatically.
Light switch in position 8: rear fog
light can only be switched on with
front fog lights.
The vehicle rear fog light is
deactivated when towing a trailer or a
plug is connected with the socket,
e.g. when a bicycle carrier is used.
When the vehicle is parked, the
parking lights on one side can be
activated:
1. Switch off ignition.
2. Move the lever all the way up
(right parking lights) or down (left
parking lights).
Confirmed by a signal and the
corresponding turn light control
indicator.
106
Lighting
Interior lighting
Instrument panel
illumination control
Interior lights
Rear courtesy lights
During entry and exit of the vehicle,
the front and rear courtesy lights
automatically switch on and then off
after a delay.
Illuminate in conjunction with the front
courtesy light.
Note
In the event of an accident with
airbag deployment the courtesy
lights are turned on automatically.
Reading lights
Front courtesy light
Brightness of the following lights can
be adjusted when headlights are
switched on:
● instrument cluster illumination
● Info Display
● illuminated switches and
operation elements
Turn thumb wheel A and hold until
the desired brightness is obtained.
Operated by pressing s and t in the
courtesy lights.
: automatic switching on
and off
press u : on
press v : off
w
Lighting
Lighting features
Centre console lighting
A spotlight integrated in the overhead
console illuminates the centre
console when headlights are
switched on.
Entry lighting
Welcome lighting
Illustration shows rear reading lights.
Sun visor lights
Illuminates when the cover is opened.
Some or all of the following lights are
switched on for a short time by
unlocking the vehicle:
● headlights
● tail lights
● number plate lights
● instrument panel light
● interior lights
The number of activated lights
depends on the surrounding light
conditions.
The lighting switches off immediately
when the ignition is switched on.
107
This function can be activated or
deactivated in the vehicle
personalisation.
Vehicle personalisation 3 95.
The following lights will additionally
switch on when the driver's door is
opened:
● illumination of some switches
● Driver Information Centre
● door pocket lights
Exit lighting
The following lights are switched on if
the ignition is switched off:
● interior lights
● instrument panel light
They will switch off automatically after
a delay. This function works only in
the dark.
108
Lighting
Battery discharge protection
Switching off interior lights
Vehicle battery state of charge
function
To prevent discharge of the vehicle
battery when the ignition is switched
off, some interior lights are switched
off automatically after some time.
The function guarantees longest
vehicle battery life via a generator
with controllable power output and
optimised power distribution.
To prevent discharge of the vehicle
battery when driving, the following
systems are reduced automatically in
two stages and finally switched off:
● auxiliary heater
● heated rear window and heated
mirrors
● heated seats
● fan
In the second stage, a message
which confirms the activation of the
vehicle battery discharge protection
will be displayed in the Driver
Information Centre.
Climate control
Climate control
Climate control systems ............. 109
Heating and ventilation system 109
Air conditioning system ........... 110
Electronic climate control
system .................................... 113
Auxiliary heater ........................ 117
Air vents ..................................... 118
Adjustable air vents ................. 118
Fixed air vents ......................... 119
Maintenance .............................. 119
Air intake ................................. 119
Air conditioning regular
operation ................................ 119
Service .................................... 119
Climate control systems
Heating and ventilation
system
109
Temperature £
Adjust the temperature by turning
£ to the desired temperature.
red area : warmer
blue area : colder
Heating will not be fully effective until
the engine has reached normal
operating temperature.
Air distribution l M K
Controls for:
● temperature £
● air distribution l, M and K
● fan speed Z
● demisting and defrosting à
● heated rear window and heated
exterior mirrors b
● heated windscreen ,
● heated seats ß
Press:
l : to windscreen and front door
windows
M : to head area and rear seats via
adjustable front air vents
K : to front and rear foot well and
windscreen
Combinations are possible.
Fan speed Z
Adjust the air flow by turning Z to the
desired speed.
110
Climate control
Demisting and defrosting the
windows á
Press á: the air distribution is
directed towards the windscreen.
● Set temperature controller £ to
warmest level.
● Set fan speed Z to highest level.
● Switch on heated rear window b.
● Open side air vents as required
and direct them towards the door
windows.
Heated rear window b 3 38.
Heated exterior mirrors b 3 34.
Heated windscreen , 3 38.
Heated seats ß 3 44.
Air conditioning system
●
Controls for:
● temperature £
● air distribution l, M and K
● fan speed Z
● demisting and defrosting à
● air conditioning A/C
● air recirculation 4
● heated rear window and heated
exterior mirrors b
●
●
heated windscreen ,
heated seats ß
Some changes of settings are
indicated briefly in the Info Display.
Activated functions are indicated by
the LED in the respective button.
Temperature £
Adjust the temperature by turning
£ to the desired temperature.
red area : warmer
blue area : colder
Heating will not be fully effective until
the engine has reached normal
operating temperature.
Climate control
Air distribution l M K
Press:
l : to windscreen and front door
windows
M : to head area and rear seats via
adjustable front air vents
K : to front and rear foot well and
windscreen
Combinations are possible.
Fan speed Z
Adjust the air flow by turning Z to the
desired speed.
Air conditioning A/C
Press A/C to switch on cooling.
Activation is indicated by the LED in
the button. Cooling is only functional
when the engine is running and
climate control fan is switched on.
Press A/C again to switch off cooling.
The air conditioning system cools and
dehumidifies (dries) as soon as the
outside temperature is slightly above
the freezing point. Therefore
condensation may form and drip from
under the vehicle.
If no cooling or drying is required,
switch off the cooling system for fuel
saving reasons.
Activated cooling may inhibit
Autostops.
Stop-start system 3 126.
111
Demisting and defrosting the
windows à
●
●
●
●
●
●
●
Press à: the air distribution is
directed towards the windscreen.
Set temperature controller £ to
warmest level.
Switch on air conditioning A/C if
required.
Set fan speed Z to highest level.
Switch on heated rear window b.
Switch on heated
windscreen ,.
Open side air vents as required
and direct them towards the door
windows.
112
Climate control
Note
If à is pressed while the engine is
running, an Autostop will be inhibited
until à is pressed again.
If à is pressed while the engine is in
an Autostop, the engine will restart
automatically.
Stop-start system 3 126.
Air recirculation system 4
Press 4 again to deactivate air
recirculation mode.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling, the
air humidity increases, so the
windows may mist up from inside.
The quality of the passenger
compartment air deteriorates,
which may cause the occupants to
feel drowsy.
In warm and very humid ambient air
conditions, the windscreen may mist
up from outside when cold air is
directed towards it. If windscreen
mists up from outside, activate
windscreen wiper and deactivate l.
Press 4 to activate air recirculation
mode, LED is indicated.
Select air recirculation to assist in
cooling the interior or in blocking
outside odours or exhaust.
Maximum cooling
Briefly open the windows so that hot
air can disperse quickly.
● Switch on air conditioning A/C.
● Press 4 for air recirculation
system on.
● Press M for air distribution.
● Set temperature control £ to
coldest level.
● Set fan speed Z to highest level.
● Open all vents.
Heated rear window b 3 38.
Heated exterior mirrors b 3 34.
Heated windscreen , 3 38.
Climate control
Heated seats ß 3 44.
Electronic climate control
system
The dual zone climate control allows
different temperatures for driver side
and front passenger side.
In automatic mode, temperature, fan
speed and air distribution are
regulated automatically.
Controls for:
● temperature on driver side £
● MENU enters the Climate setting
menu in the Info Display
● fan speed Z
●
●
●
●
●
●
automatic mode AUTO
temperature on front passenger
side £
cooling A/C
manual air recirculation 4
demisting and defrosting à
heated rear window and heated
exterior mirrors b
heated windscreen ,
●
● heated seats ß
Activated functions are indicated by
the LED in the respective control.
The electronic climate control system
is only fully operational when the
engine is running.
Make sure the sun sensor used by the
electronic climate control system is
not covered 3 10.
113
Climate settings menu
Press MENU to enter the climate
setting menu.
Settings for:
● air distribution l, M, K
● fan speed Z
● temperature for driver and
passenger side
● dual zone temperature
synchronisation MONO
● cooling A/C
● automatic mode AUTO
114
Climate control
Climate setting menu can also be
displayed
● by pressing ! and
thenselecting Climate on the 7''
Colour Info Display or
● by pressing Í and then selecting
Climate from the menu on the 8''
Colour Info Display.
Automatic mode AUTO
Basic settings for automatic control
with maximum comfort:
● Press AUTO to start the cooling
automatically.
● Open all air vents to allow
optimised air distribution in
automatic mode.
● Set the preselected
temperatures for driver and front
passenger using the left and right
control dial. Recommended
temperature is 22 °C.
Temperature is indicated in
displays beside the controls and
in the climate settings menu.
● Air recirculation mode 4 should
be deactivated. When
deactivated the LED in the button
is not illuminated.
Manual settings
Climate control system settings can
be changed by activating the
following functions:
Fan speed Z
Adjust the air flow by turning rotary
knob Z to the desired speed.
To return to automatic mode, press
AUTO.
Climate control
Air distribution l, M, K
Temperature preselection £
115
If the minimum temperature Lo is set,
the climate control system runs at
maximum cooling, if cooling A/C is
switched on.
If the maximum temperature Hi is set,
the climate control system runs at
maximum heating.
Note
If A/C is switched on, reducing the
set cabin temperature can cause the
engine to restart from an Autostop or
inhibit an Autostop.
Press MENU.
Touch
l : to windscreen and front door
windows
M : to head area and rear seats via
adjustable air vents
K : to front and rear foot well and
windscreen
To return to automatic air distribution,
press AUTO.
Set the preselected temperatures
separately for driver and front
passenger to the desired value using
the left and right controls. The dial on
the passenger side changes the
temperature for the passenger side.
The dial on the driver's side changes
the temperature for the driver's side or
for both sides depending on
activation of synchronisation MONO
in the climate settings menu. Press
MENU to enter the menu.
Recommended temperature is 22 °C.
Temperature is indicated in displays
beside the controls and in the climate
settings menu.
Stop-start system 3 126.
Dual zone temperature
synchronisation MONO or SYNC
Press MENU to enter the menu.
Touch MONO or SYNC to link
passenger side temperature setting
to the driver side.
When passenger side control dial will
be adjusted, synchronisation is
deactivated.
116
Climate control
Cooling A/C
Manual air recirculation 4
compartment air deteriorates,
which may cause the occupants to
feel drowsy.
In warm and very humid ambient air
conditions, the windscreen may mist
up from outside, when cold air is
directed towards it. If windscreen
mists up from outside, activate
windscreen wiper and deactivate l.
Press A/C to switch on cooling. The
LED in the button illuminates to
indicate activation. Cooling is only
functional when the engine is running
and climate control fan is switched on.
Press A/C again to switch off cooling.
The air conditioning system cools and
dehumidifies (dries) when outside
temperature is above a specific level.
Therefore condensation may form
and drip from under the vehicle.
If no cooling or drying is required,
switch off the cooling system for fuel
saving reasons.
Press 4 to activate the air
recirculation mode. The LED in the
button illuminates to indicate
activation.
Press 4 again to deactivate
recirculation mode.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling, the
air humidity increases, so the
windows may mist up from inside.
The quality of the passenger
Climate control
Demisting and defrosting the
windows à
Note
If à is pressed while the engine is
running, an Autostop will be inhibited
until à is pressed again.
If à is pressed while the engine is in
an Autostop, the engine will restart
automatically.
Stop-start system 3 126.
●
●
●
●
●
●
Press à. The LED in the button
illuminates to indicate activation.
Temperature and air distribution
are set automatically and the fan
runs at high speed.
Switch on cooling by pressing
A/C, if required.
Switch on heated rear window b.
Switch on heated
windscreen ,.
To return to previous mode press
à again, to return to automatic
mode press AUTO.
Deactivation of electronic climate
control system
Cooling, fan and automatic mode can
be switched off by turning control dial
Z anticlockwise.
Activation by switching on the fan or
pressing AUTO.
Heated rear window b 3 38.
Heated exterior mirrors b 3 34.
Heated windscreen , 3 38.
Heated seats ß 3 44.
117
Auxiliary heater
Air heater
Quickheat is an electric auxiliary air
heater which automatically warms up
the passenger compartment more
quickly.
118
Climate control
Air vents
Adjustable air vents
At least two air vents must be open
while cooling is on.
9 Warning
Direct the flow of air by tilting and
swivelling the slats.
To close the vent, swivel the slats
inwards.
Centre air vent on top of the
instrument panel
Outer air vents in the instrument
panel
Do not attach any objects to the
slats of the air vents. Risk of
damage and injury in case of an
accident.
Centre air vents in the instrument
panel
Close air flow by turning the thumb
wheel to the front.
Direct the flow of air by tilting and
swivelling the slats.
To close the vent, swivel the slats
outwards.
Climate control
Air vent in the glovebox
Maintenance
Air intake
Additional air vents are located
beneath the windscreen and door
windows and in the foot wells.
areas with high dust levels or which
are sensitive to environmental
allergens.
Passenger compartment air filter
replacement may also be needed if
there is reduced air flow, windows
fogging up, or odors.
Your dealer can help to determine
when it is the right time to replace the
filter.
Air conditioning regular
operation
The air vent can be opened or closed
by turning.
Fixed air vents
119
The air intake in front of the
windscreen in the engine
compartment must be kept clear to
allow air intake. Remove any leaves,
dirt or snow.
Cabin air filter
Change filter regulary for maximum
effect.
More frequent passenger
compartment air filter replacement
may be needed, if you drive in areas
with heavy traffic, poor air quality,
In order to ensure continuously
efficient performance, cooling must
be operated for a few minutes once a
month, irrespective of the weather
and time of year. Operation with
cooling is not possible when the
outside temperature is too low.
Service
For optimal cooling performance, it is
recommended to annually check the
climate control system, starting 3
years after initial vehicle registration,
including:
120
●
●
●
●
●
●
●
Climate control
functionality and pressure test
heating functionality
leakage check
check of drive belts
cleaning of condenser and
evaporator drainage
performance check
cabin air filter check
Driving and operating
Driving and
operating
Driving hints ............................... 122
Control of the vehicle ............... 122
Steering ................................... 122
Starting and operating ............... 122
New vehicle running-in ............ 122
Ignition switch positions ........... 123
Power button ........................... 123
Starting the engine .................. 124
Overrun cut-off ........................ 126
Stop-start system .................... 126
Parking .................................... 128
Engine exhaust .......................... 129
Exhaust filter ............................ 129
Catalytic converter ................... 130
AdBlue ..................................... 130
Automatic transmission .............. 133
Transmission display ............... 133
Gear selection ......................... 134
Manual mode ........................... 135
Electronic driving programmes 135
Fault ........................................ 135
Interruption of power supply .... 135
Manual transmission .................. 136
Brakes ........................................ 137
Antilock brake system ............. 137
Parking brake .......................... 138
Brake assist ............................. 139
Hill start assist ......................... 139
Ride control systems ................. 139
Electronic Stability Control and
Traction Control system ......... 139
Driver assistance systems ......... 140
Cruise control .......................... 140
Speed limiter ........................... 143
Forward collision alert ............. 145
Active emergency braking ....... 147
Front pedestrian protection ..... 149
Parking assist .......................... 150
Advanced parking assist ......... 153
Side blind spot alert ................. 158
Panoramic view system ........... 159
Rear view camera ................... 162
Lane departure warning .......... 163
Driver alert ............................... 164
Fuel ............................................ 166
Fuel for petrol engines ............. 166
Fuel for diesel engines ............ 166
Refuelling ................................ 167
Trailer hitch ................................ 169
General information ................. 169
Driving characteristics and
towing tips .............................. 169
121
Trailer towing ........................... 170
Towing equipment ................... 170
122
Driving and operating
Driving hints
Control of the vehicle
Never coast with engine not
running
Many systems will not function in this
situation (e.g. brake servo unit, power
steering). Driving in this manner is a
danger to yourself and others.
All systems function during an
Autostop.
Stop-start system 3 126.
Pedals
To ensure the pedal travel is
uninhibited, there must be no mats in
the area of the pedals.
Use only floor mats, which fit properly
and are fixed by the retainers on the
driver side.
Steering
If power steering assist is lost
because the engine stops or due to a
system malfunction, the vehicle can
be steered but may require increased
effort.
Starting and operating
New vehicle running-in
Do not brake unnecessarily hard for
the first few journeys.
During the first drive, smoke may
occur because of wax and oil
evaporating off the exhaust system.
Park the vehicle in the open for a
while after the first drive and avoid
inhaling the fumes.
During the running-in period, fuel and
engine oil consumption may be
higher.
Additionally, the cleaning process of
the exhaust filter may take place more
often.
Exhaust filter 3 129.
Driving and operating
Ignition switch positions
9 Danger
Never remove the key from
ignition switch during driving as
this will cause steering wheel lock.
Power button
0 : ignition off: some functions
remain active until key is
removed or driver's door is
opened, provided the ignition was
on previously
1 : ignition on power mode: ignition
is on, control indicators illuminate
and most electrical functions are
operable
2 : engine start: release key after
engine has been started
Steering wheel lock
Remove key from ignition switch and
turn steering wheel until it engages.
123
Engine start
Operate the clutch pedal, the brake
pedal and press Start/Stop. Release
the button after starting procedure
begins.
Engine and ignition off
Press Start/Stop briefly in each mode
or when engine is running and vehicle
is stationary. Some functions remain
active until driver's door is opened,
provided the ignition was on
previously.
Emergency shut off during driving
If the engine needs to be switched off
during driving in case of emergency,
press Start/Stop for 5 seconds.
9 Danger
The electronic key must be inside the
vehicle.
Ignition on power mode without
starting the engine
Press Start/Stop without operating a
pedal. Control indicators illuminate
and most electrical functions are
operable.
Switching off the engine during
driving may cause loss of power
support for brake and steering
systems. Assistance systems and
airbag systems are disabled.
Lighting and brake lights will
extinguish. Therefore power down
124
Driving and operating
the engine and ignition while
driving only when required in case
of emergency.
display No Remote Detected or
Replace Battery in Remote Key when
you try to start the vehicle.
For unlocking or locking the doors,
see fault in radio remote control unit
or electronic key system 3 23.
Steering wheel lock
Starting the engine
The steering wheel lock activates
automatically when:
● The vehicle is stationary.
● The ignition has been switched
off.
To release steering wheel lock, open
and close driver's door and switch the
ignition on power mode or start the
engine directly.
Vehicles with ignition switch
9 Warning
If the vehicle battery is discharged,
the vehicle must not be towed,
tow-started or jump-started as the
steering wheel lock cannot be
disengaged.
Operation in case of failure
If either the electronic key fails or the
battery of the electronic key is weak,
the Driver Information Centre may
Hold the electronic key with buttons
outside at the marking on the steering
column cover as shown in the
illustration.
Operate the clutch pedal, the brake
pedal and press Start/Stop. Release
the button after starting procedure
begins.
This option is intended for
emergencies only. Replace the
electronic key battery as soon as
possible 3 22.
●
●
●
●
Turn key to position 1.
Move the steering wheel slightly
to release the steering wheel
lock.
Manual transmission: operate
clutch and brake pedal.
Automatic transmission: operate
brake pedal and move selector
lever to P or N.
Driving and operating
●
●
Do not operate accelerator pedal.
Diesel engines: wait until control
indicator ! extinguishes.
● Turn key to position 2 and
release after the engine has been
started.
Manual transmission: during an
Autostop, the engine can be started
by depressing the clutch pedal
3 126.
Automatic transmission: during an
Autostop, the engine can be started
by releasing the brake pedal 3 126.
Vehicles with power button
●
Manual transmission: operate
clutch and brake pedal.
● Automatic transmission: operate
brake pedal and move selector
lever to P or N.
● Do not operate accelerator pedal.
● Press Start/Stop button. Release
button after starting procedure
begins.
● Diesel engine starts after control
indicator ! for preheating
extinguishes.
● Before restarting or to switch off
the engine when vehicle is
stationary, press Start/Stop once
more briefly.
To start the engine during an
Autostop:
● Manual transmission: during an
Autostop, the engine can be
started by depressing the clutch
pedal 3 126.
● Automatic transmission: during
an Autostop, the engine can be
started by releasing the brake
pedal 3 126.
125
Starting the vehicle at low
temperatures
Starting the engine without additional
heaters is possible down to -25 °С for
diesel engines and -30 °C for petrol
engines.
Required is an engine oil with the
correct viscosity, the correct fuel,
performed services and a sufficiently
charged vehicle battery.
With temperatures below -30 °C the
automatic transmission requires a
warming phase of approx. 5 minutes.
The selector lever must be in position
P.
Caution
Under extreme cold temperatures,
idle engine for maximum
5 minutes otherwise the engine
might be damaged.
126
Driving and operating
Turbo engine warm-up
Activation
Upon start-up, engine available
torque may be limited for a short time,
especially when the engine
temperature is cold. The limitation is
to allow the lubrication system to fully
protect the engine.
The stop-start system is available as
soon as the engine is started, the
vehicle starts-off and the conditions
as stated below in this section are
fulfilled.
The system is ready to operate when
the LED in the button Ò is not
illuminated. To activate the system
when the system is deactivated,
press Ó.
If the stop-start system is temporarily
not available and the button Ò is
pressed, the LED in the button
flashes.
Overrun cut-off
The fuel supply is automatically cut off
during overrun, i.e. when the vehicle
is driven with a gear engaged but
accelerator pedal is released.
Depending on driving conditions, the
overrun cut-off may be deactivated.
Stop-start system
The stop-start system helps to save
fuel and to reduce the exhaust
emissions. When conditions allow, it
switches off the engine as soon as the
vehicle is at a low speed or at a
standstill, e.g. at a traffic light or in a
traffic jam.
Deactivation
Deactivate the stop-start system
manually by pressing Ò. The
deactivation is indicated when the
LED in the button illuminates.
Autostop
Vehicles with manual transmission
An Autostop can be activated at a
standstill.
Activate an Autostop as follows:
● Depress the clutch pedal.
● Set the lever to neutral.
● Release the clutch pedal.
Driving and operating
The engine will be switched off while
the ignition stays on.
Vehicles with automatic transmission
If the vehicle is at a standstill with
depressed brake pedal, Autostop is
activated automatically.
The engine will be switched off while
the ignition stays on.
The stop-start system will be disabled
on inclines of 12% or more.
Indication
An Autostop is indicated by control
indicator D.
During an Autostop, the heating and
brake performance will be
maintained.
Conditions for an Autostop
The stop-start system checks if each
of the following conditions is fulfilled.
●
The stop-start system is not
manually deactivated.
● The driver's door is closed or the
driver's seat belt is fastened.
● The vehicle battery is sufficiently
charged and in good condition.
● The engine is warmed up.
● The engine coolant temperature
is not too high.
● The engine exhaust temperature
is not too high, e.g. after driving
with high engine load.
● The ambient temperature is not
too low or too high.
● The climate control system
allows an Autostop.
● The brake vacuum is sufficient.
● The self-cleaning function of the
exhaust filter is not active.
● The vehicle was driven at least at
walking speed since the last
Autostop.
Otherwise an Autostop will be
inhibited.
127
Note
The Autostop may be inhibited for
several hours after a battery
replacement or reconnection.
Certain settings of the climate control
system may inhibit an Autostop. See
Climate control chapter for more
details 3 110.
If an autostop is temporarily not
available, D flashes green 3 86.
Immediately after driving at a higher
speed an Autostop may be inhibited.
Vehicle battery discharge protection
To ensure reliable engine restarts,
several vehicle battery discharge
protection features are implemented
as part of the stop-start system.
Power saving measures
During an Autostop, several electrical
features such as auxiliary electric
heater or rear window heating are
disabled or switched to a power
saving mode. The fan speed of the
climate control system is reduced to
save power.
128
Driving and operating
Restart of the engine by the driver
Vehicles with automatic transmission
The engine is restarted if
● the brake pedal is released while
the selector lever is in position D
or M
● or the brake pedal is released or
the selector lever is in position N
when the selector lever is moved
to position D or M
● or the selector lever is moved to
position R.
The stop-start system is
manually deactivated.
● The driver's seat belt is
unfastened or the driver's door is
opened.
● The engine temperature is too
low.
● The charging level of the vehicle
battery is below a defined level.
● The brake vacuum is not
sufficient.
● The climate control system
requests an engine start.
If an electrical accessory, e.g. a
portable CD player, is connected to
the power outlet, a brief power drop
during the restart might be noticeable.
Restart of the engine by the stopstart system
Parking
Vehicles with manual transmission
Depress the clutch pedal without
depressing the brake pedal to restart
the engine.
The selector lever must be in neutral
to enable an automatic restart.
If one of the following conditions
occurs during an Autostop, the
engine will be restarted automatically
by the stop-start system:
●
9 Warning
●
Do not park the vehicle on an
easily ignitable surface. The
high temperature of the
exhaust system could ignite the
surface.
●
●
●
●
●
Always apply the parking
brake. Activate the parking
brake without pressing the
release button. Apply as firmly
as possible on a downhill slope
or uphill slope. Depress brake
pedal at the same time to
reduce operating force.
Switch off the engine.
If the vehicle is on a level
surface or uphill slope, engage
first gear or set the selector
lever to position P. On an uphill
slope, turn the front wheels
away from the kerb.
If the vehicle is on a downhill
slope, engage reverse gear or
set the selector lever to position
P. Turn the front wheels
towards the kerb.
Close the windows.
Remove the ignition key from
the ignition switch or switch off
ignition on vehicles with power
button. Turn the steering wheel
until the steering wheel lock is
felt to engage.
Driving and operating
●
●
●
Lock the vehicle with e on the
radio remote control.
Or with electronic key system
press marking on front door
handles 3 22.
Activate the anti-theft alarm
system 3 31.
The engine cooling fans may run
after the engine has been
switched off 3 176.
Caution
After running at high engine
speeds or with high engine loads,
operate the engine briefly at a low
load or run in neutral for
approx. 30 seconds before
switching off, in order to protect
the turbocharger.
Caution
Under extreme cold temperatures,
idle engine for maximum
5 minutes otherwise the engine
might be damaged.
Note
In the event of an accident with
airbag deployment, the engine is
switched off automatically if the
vehicle comes to a standstill within a
certain time.
In countries with extreme low
temperatures it may be necessary to
park the vehicle without applied
parking brake. Make sure to park the
vehicle on a level surface.
Keys, locks 3 20.
Laying-up the vehicle for a long
period of time 3 175.
129
Engine exhaust
9 Danger
Engine exhaust gases contain
poisonous carbon monoxide,
which is colourless and odourless
and could be fatal if inhaled.
If exhaust gases enter the interior
of the vehicle, open the windows.
Have the cause of the fault
rectified by a workshop.
Avoid driving with an open load
compartment, otherwise exhaust
gases could enter the vehicle.
Exhaust filter
Automatic cleaning process
The exhaust filter system filters soot
particles out of the exhaust gases.
The start of saturation of the exhaust
filter is indicated by the temporary
illumination of % or C,
accompanied by a message in the
Driver Information Centre.
130
Driving and operating
As soon as the traffic conditions
permit, regenerate the filter by driving
at a vehicle speed of at least 60 km/h
until the control indicator
extinguishes.
Note
On a new vehicle, the first exhaust
filter regeneration operations may
be accompanied by a burning smell,
which is normal. Following
prolonged operation of the vehicle at
very low speed or at idle, water
vapour can be emitted at the
exhaust on acceleration. This does
not affect the behaviour of the
vehicle or the environment.
Cleaning process not possible
If % or C stays on, accompanied
by an audible signal and a message,
this indicates that the exhaust filter
additive level is too low.
The reservoir must be topped-up
without delay. Seek the assistance of
a workshop.
Catalytic converter
AdBlue
The catalytic converter reduces the
amount of harmful substances in the
exhaust gases.
General information
Caution
Fuel grades other than those listed
on pages 3 166, 3 226 could
damage the catalytic converter or
electronic components.
Unburnt fuel will overheat and
damage the catalytic converter.
Therefore avoid excessive use of
the starter, running the fuel tank
dry and starting the engine by
pushing or towing.
In the event of misfiring, uneven
engine running, a reduction in engine
performance or other unusual
problems, have the cause of the fault
rectified by a workshop as soon as
possible. In an emergency, driving
can be continued for a short period,
keeping vehicle speed and engine
speed low.
The selective catalytic reduction
(BlueInjection) is a method to
substantially reduce the nitrogen
oxides in the exhaust emission. This
is achieved by injecting a Diesel
Exhaust Fluid (DEF) into the exhaust
system. The ammonia released by
the fluid reacts with nitrous gases
(NOx) from the exhaust and turns it
into nitrogen and water.
The designation of this fluid is
AdBlue®. It is a non-toxic, nonflammable, colourless and odourless
fluid which consists of 32% urea and
68% water.
9 Warning
Avoid contact of your eyes or skin
with AdBlue.
In case of eye or skin contact,
rinse off with water.
Driving and operating
Caution
Avoid contact of the paintwork with
AdBlue.
In case of contact, rinse off with
water.
AdBlue freezes at a temperature of
approx. -11 °C. As the vehicle is
equipped with an AdBlue pre-heater,
the emissions reduction at low
temperatures is ensured. The AdBlue
pre-heater works automatically.
Level warnings
The AdBlue consumption is approx.
1.5 l per 1000 km. The consumption
can be higher depending on driving
behaviour (e.g. high load or towing).
Depending on the calculated range of
AdBlue, different messages are
displayed in the Driver Information
Centre. The messages and the
restrictions are a legal requirement.
The first possible warning message
appears at an AdBlue range below
2400 km, shows up at each start and
each 300 km range reduction:
Top up AdBlue: Starting impossible in
2400 km
Additionally, control indicator Y
illuminates continuously and a chime
sounds with every message pop-up.
At an AdBlue range below 600 km,
the following warning message is
being displayed, shows up at each
start and each 20 km range reduction:
Top up AdBlue: Starting impossible in
600 km
Additionally, control indicator Y
flashes continuously and a chime
sounds with every message pop-up.
Note
In case of high AdBlue consumption,
the Driver Information Centre may
display this warning without the
previous warning stages.
The last warning level is entered
when the AdBlue tank is empty.
Restart of the engine is not possible.
The following warning message is
being displayed and cannot be
dismissed:
Top up AdBlue: Starting impossible
131
Additionally, control indicator Y
flashes continuously and engine
cannot be restarted until AdBlue tank
is being filled with at least 5 l.
High emission warnings
If the exhaust emission rises above a
certain value, warnings similar to the
range warnings will be displayed in
the Driver Information Centre.
Requests to have the exhaust system
checked and finally the
announcement of the prevention of
an engine restart are displayed.
These restrictions are a legal
requirement.
Consult a workshop for assistance.
Refilling AdBlue
Caution
Only use AdBlue that complies
with European standards
DIN 70 070 and ISO 22241-1.
Do not use additives.
132
Driving and operating
Do not dilute AdBlue.
Otherwise the selective catalytic
reduction system could be
damaged.
Note
Whenever a filling pump with a
nozzle for passenger cars is not
available at a filling station, use only
AdBlue bottles or canisters with a
sealed refill adapter for refilling, to
prevent splashback and overspill,
and in order to ensure that the fumes
from the tank are captured and do
not emerge. AdBlue in bottles or
canisters is available in many filling
stations and can be purchased e.g.
at Opel dealers and other retail
outlets.
Whenever a filling pump with a
nozzle for passenger cars is not
available at a filling station, use only
AdBlue bottles or canisters with a
sealed refill adapter for refilling, to
prevent splashback and overspill,
and in order to ensure that the fumes
from the tank are captured and do
not emerge. AdBlue in bottles or
canisters is available in many filling
stations and can be purchased e.g.
at Vauxhall dealers and other retail
outlets.
Since AdBlue has a limited
durability, check the date of expiry
before refilling.
Note
Refill the tank to a level of at least
5 l to ensure that the new AdBlue
level is being detected.
In case AdBlue refill is not
successfully detected:
1. Continuously drive the vehicle
for 10 min making sure that
vehicle speed is always higher
than 20 km/h.
2. If AdBlue refill is detected
successfully, AdBlue supplydriven warnings or limitations will
disappear.
If AdBlue refill is still not detected,
seek the assistance of a workshop.
If AdBlue must be refilled at
temperatures below -11 °C, the
refilling of AdBlue may not be
detected by the system. In this
event, park the vehicle in a space
with a higher ambient temperature
until AdBlue is liquified.
Note
When unscrewing the protective cap
from the filler neck, ammonia fumes
may emerge. Do not inhale as the
fumes have a pungent smell. The
fumes are not harmful by inhalation.
It is recommended to fill the AdBlue
tank completely.
The vehicle must be parked on a level
surface.
The filler neck for AdBlue is located
behind the fuel filler flap, which is
located at left rear side of the vehicle.
The fuel filler flap can only be opened
if the vehicle is unlocked.
1. Switch off ignition.
2. Close all doors to avoid ammonia
fumes entering the interior of the
vehicle.
3. Release the fuel filler flap by
pushing the flap 3 167.
Driving and operating
9. Unscrew the hose from the filler
neck.
10. Mount the protective cap and turn
clockwise until it engages.
Note
Dispose of AdBlue canister
according to environmental
requirements. Hose can be reused
after flushing with clear water before
AdBlue dries out.
4. Unscrew protective cap from the
filler neck.
5. Open AdBlue canister.
6. Mount one end of the hose on the
canister and screw the other end
on the filler neck.
7. Lift the canister until it is empty, or
until the flow from the canister has
stopped. This can take up to
5 minutes.
8. Place the canister on the ground
to empty the hose, wait 15
seconds.
133
Automatic transmission
The automatic transmission permits
automatic gearshifting (automatic
mode) or manual gearshifting
(manual mode).
Manual shifting is possible in manual
mode by tapping the selector lever to
+ or - 3 135.
Transmission display
The mode or selected gear is shown
in the Driver Information Centre.
D and the number of the engaged
gear indicates automatic mode.
134
Driving and operating
M and the number of the selected
gear indicates manual mode.
R indicates reverse gear.
N indicates neutral position.
P indicates park position.
Gear selection
Move the selector lever in the shifting
gate as shown in the illustration
above.
P : park position, wheels are locked,
engage only when the vehicle is
stationary and the parking brake
is applied
R : reverse gear, engage only when
the vehicle is stationary
N : neutral
D : automatic mode
M : manual mode
< : upshift in manual mode
] : downshift in manual mode
The selector lever is locked in P and
can only be moved when the ignition
is on and the brake pedal is applied.
The engine can only be started with
the lever in position P or N. When
position N is selected, press the brake
pedal or apply the parking brake
before starting.
Do not accelerate while engaging a
gear. Never depress the accelerator
pedal and brake pedal at the same
time.
When a gear is engaged, the vehicle
slowly begins to creep when the
brake is released.
Engine braking
To utilise the engine braking effect,
select a lower gear in good time when
driving downhill, see manual mode.
Rocking the vehicle
Rocking the vehicle is only
permissible if the vehicle is stuck in
sand, mud or snow. Move the selector
lever between D and R in a repeat
pattern. Do not race the engine and
avoid sudden acceleration.
Parking
Apply the parking brake and engage
P.
Driving and operating
Manual mode
In manual mode, no automatic
shifting to a higher gear takes place
at high engine revolutions.
Gear shifting 3 84.
Electronic driving
programmes
●
Move selector lever out of position D
towards the left in position M.
Tap selector lever towards + to shift
to a higher gear.
Tap the selector lever towards - to
shift to a lower gear.
If a higher gear is selected when
vehicle speed is too low, or a lower
gear when vehicle speed is too high,
the shift is not executed. This can
cause a message in the Driver
Information Centre.
●
●
Following a cold start, the
operating temperature
programme increases engine
speed to quickly bring the
catalytic converter to the required
temperature.
Special programmes
automatically adapt the shifting
points when driving up inclines or
down hills.
In snowy or icy conditions or on
other slippery surfaces, the
electronic transmission control
enables the driver to select
manually first, second or third
gear for starting off.
135
Kickdown
Pressing down the accelerator pedal
beyond the kickdown detent will lead
to maximum acceleration
independent of selected driving
mode. The transmission shifts to a
lower gear depending on engine
speed.
Fault
In the event of a fault a message is
displayed in the Driver Information
Centre.
Vehicle messages 3 94.
Electronic transmission control
enables only third gear. The
transmission no longer shifts
automatically.
Do not drive faster than 100 km/h.
Have the cause of the fault remedied
by a workshop.
Interruption of power supply
In the event of an interruption of
power supply, the selector lever
cannot be moved out of the P
position.
136
Driving and operating
If the vehicle battery is discharged,
start the vehicle using jump leads
3 207.
If the vehicle battery is not the cause
of the fault, release the selector lever.
1. Apply the parking brake.
2. Release the selector lever trim
from the centre console. Poke
with a finger into the leather
socket below the selector lever
and push the trim upwards.
3. Push down the button and move
the selector lever out of P. Have
the cause of the power supply
interruption remedied by a
workshop.
4. Mount the selector lever trim onto
the centre console and refit.
Manual transmission
To engage reverse on 5-speed
transmission, depress the clutch
pedal and move the selector lever to
the right and rear.
Driving and operating
When clutch slip is detected for a
specific time, the engine power will be
reduced. A warning is displayed in the
Driver Information Centre. Release
the clutch.
Caution
It is not advisable to drive with the
hand resting on the selector lever.
To engage reverse on 6-speed
transmission, depress the clutch
pedal, pull the ring under the selector
lever and move the selector lever
quite to the left and front.
If the gear does not engage, set the
lever to neutral, release the clutch
pedal and depress again; then repeat
gear selection.
Do not slip the clutch unnecessarily.
When operating, depress the clutch
pedal completely. Do not use the
pedal as a foot rest.
Gear shifting 3 84.
Stop-start system 3 126.
137
Brakes
The brake system comprises two
independent brake circuits.
If a brake circuit fails, the vehicle can
still be braked using the other brake
circuit. However, braking effect is
achieved only when the brake pedal
is depressed firmly. Considerably
more force is needed for this. The
braking distance is extended. Seek
the assistance of a workshop before
continuing the journey.
When the engine is not running, the
support of the brake servo unit
disappears once the brake pedal has
been depressed once or twice.
Braking effect is not reduced, but
braking requires significantly greater
force. It is especially important to bear
this in mind when being towed.
Control indicator R 3 83.
Antilock brake system
Antilock brake system (ABS)
prevents the wheels from locking.
138
Driving and operating
ABS starts to regulate brake pressure
as soon as a wheel shows a tendency
to lock. The vehicle remains
steerable, even during hard braking.
ABS control is made apparent
through a pulse in the brake pedal
and the noise of the regulation
process.
For optimum braking, keep the brake
pedal fully depressed throughout the
braking process, despite the fact that
the pedal is pulsating. Do not reduce
the pressure on the pedal.
When braking in an emergency, the
hazard warning flashers are switched
on automatically depending on the
force of deceleration. They are
switched off automatically the first
time you accelerate.
After starting off, the system performs
a self-test which may be audible.
Control indicator u 3 84.
Fault
9 Warning
If there is a fault in the ABS, the
wheels may be liable to lock due
to braking that is heavier than
normal. The advantages of ABS
are no longer available. During
hard braking, the vehicle can no
longer be steered and may
swerve.
Have the cause of the fault remedied
by a workshop.
Parking brake
9 Warning
Before leaving the vehicle, check
parking brake status. Control
indicator R must illuminate
constantly.
9 Warning
Always apply parking brake firmly
without operating the release
button, and apply as firmly as
possible on a downhill or uphill
slope.
To release the parking brake, pull
the lever up slightly, press the
release button and fully lower the
lever.
To reduce the operating forces of
the parking brake, depress the
foot brake at the same time.
Control indicator R 3 83.
Driving and operating
Brake assist
If brake pedal is depressed quickly
and forcefully, maximum brake force
is automatically applied.
Operation of brake assist might
become apparent by a pulse in the
brake pedal and a greater resistance
when depressing the brake pedal.
Maintain steady pressure on the
brake pedal as long as full braking is
required. Maximum brake force is
automatically reduced when brake
pedal is released.
Hill start assist
The system helps prevent unintended
movement when driving away on
inclines.
When releasing the brake pedal after
stopping on an incline, brakes remain
on for further 2 seconds. The brakes
release automatically as soon as the
vehicle begins to accelerate.
139
Ride control systems
Electronic Stability Control
and Traction Control system
Electronic stability control (ESC)
improves driving stability when
necessary, regardless of the type of
road surface or tyre grip.
As soon as the vehicle starts to
swerve (understeer / oversteer),
engine output is reduced and the
wheels are braked individually.
ESC operates in combination with the
traction control system. It prevents
the driven wheels from spinning.
The traction control system is a
component of the ESC and prevents
the driven wheels from spinning. As
soon as the driven wheels starts to
spin, engine output is reduced and
the wheel spinning the most is braked
individually. This considerably
improves the driving stability of the
vehicle on slippery road surfaces.
ESC and traction control system are
operational after each engine start as
soon as the control indicator b
extinguishes.
When ESC and traction control
system operate, b flashes.
9 Warning
Do not let this special safety
feature tempt you into taking risks
when driving.
Adapt speed to the road
conditions.
Control indicator b 3 84.
140
Driving and operating
Deactivation
ESC and traction control system are
also reactivated the next time the
ignition is switched on.
Fault
If there is a fault in the system, the
control indicator b illuminates
continuously and a message appears
in the Driver Information Centre. The
system is not operational.
Have the cause of the fault remedied
by a workshop.
ESC and traction control system can
be deactivated, everytime it is
required: press a.
Control indicator a illuminates 3 85.
A status message appears in the
Driver Information Centre.
ESC and traction control system are
reactivated by pressing the a button
again, by applying the brake or in the
case that the vehicle is driven faster
than 50 km/h.
a extinguishes when ESC and
traction control system are
reactivated.
Driver assistance
systems
9 Warning
Driver assistance systems are
developed to support the driver
and not to replace the driver's
attention.
The driver stays in full control of
the vehicle and accepts full
responsibility when driving the
vehicle.
When using driver assistance
systems, always take care
regarding the current traffic
situation and follow applicable
traffic rules.
Cruise control
The cruise control can store and
maintain speeds above 40 km/h.
Additionally at least the third gear
must be engaged on manual
transmission.
Driving and operating
Additionally position D or the second
or a higher gear in position M must be
selected on automatic transmission.
Deviations from the stored speeds
may occur when driving uphill or
downhill.
The system maintains the vehicle
speed at the preset speed by the
driver, without any action on the
accelerator pedal.
The preset speed can be exceeded
temporarily by pressing the
accelerator pedal firmly.
The status and preset speed is
displayed in the Driver Information
Centre.
Do not use the cruise control if it is not
advisable to maintain a constant
speed.
Control indicator m 3 87.
Switching on the system
Activation of the functionality
Press m on the steering wheel:
symbol m and a message are
indicated in the Driver Information
Centre. The system is still not active.
Setting speed by the driver
141
142
Driving and operating
Accelerate to the desired speed and
move thumb wheel briefly to SET/-.
The current speed is stored and
maintained. Accelerator pedal can be
released.
The preset speed can then be
changed by moving thumb wheel to
RES/+ to increase or to SET/- to
decrease the speed. Move thumb
wheel repeatedly to change speed in
small steps, move and hold to change
speed in large steps.
Speed value is indicated in the Driver
Information Centre.
Adopting speed by the speed limit
recognition
The intelligent speed adaptation
informs the driver when a speed limit
is detected by the speed limit
recognition. The detected speed limit
can be used as new value for the
cruise control.
Using the camera at the top of the
windscreen, this system detects and
reads speed limit and end of speed
limit signs.
If the cruise control is active, the
recognised speed limit will be
displayed in the Driver Information
Centre and "MEM" illuminates.
Press MEM on the steering wheel to
request saving of the suggested
speed.
Press MEM on the steering wheel
once more to confirm and save the
new speed setting.
This speed is the new value for the
cruise control.
This function can be deactivated or
activated in the personalisation menu
3 95.
Exceeding the set speed
Vehicle speed can be increased by
depressing the accelerator pedal.
When the accelerator pedal is
released, the previously stored speed
is resumed.
Deactivation of the functionality
Press Ñ: cruise control is in pause
mode and a message is displayed.
The vehicle is driven without cruise
control.
Driving and operating
Cruise control is deactivated, but not
switched off. Last stored speed
remains in memory for later speed
resume.
Cruise control is deactivated
automatically when:
● The brake pedal is depressed.
● Vehicle speed is below 40 km/h.
● The Traction Control system or
Electronic Stability Control is
operating.
● The manual transmission is in N,
first or second gear.
● The automatic transmission is in
position M and first gear.
Resume stored speed
Move thumb wheel to RES/+ at a
speed above 40 km/h. The stored
speed will be obtained.
Switching off the system
Press m: the cruise control mode is
deselected and the cruise control
indication extinguishes in the Driver
Information Centre.
Pressing ß to activate the speed
limiter deactivates cruise control.
Switching off the ignition cancels any
programmed speed value.
143
The status and preset speed limit is
displayed in the Driver Information
Centre.
Switching on the system
Fault
In the event of a cruise control fault,
the speed is cleared resulting in
flashing of the dashes.
The speed limit recognition may not
operate correctly if traffic signs do not
comply with the Vienna Convention
on Road Signs and Signals.
Speed limiter
The speed limiter prevents the
vehicle from exceeding a preset
maximum speed.
The maximum speed can be set at
speeds above 30 km/h.
The driver can accelerate the vehicle
up to the preset speed. Deviations
from the limited speed may occur
when driving downhill.
The preset speed can be exceeded
temporarily by pressing the
accelerator pedal firmly.
Press ß, symbol ß and a message
are displayed in the Driver
Information Centre. The system is still
not active.
144
Driving and operating
Accelerate to the desired speed and
move thumb wheel briefly to SET/-.
The current speed is stored as
maximum speed.
The preset maximum speed can be
changed by moving thumb wheel to
RES/+ to increase or to SET/- to
decrease the desired maximum
speed. Move thumb wheel repeatedly
to change speed in small steps, move
and hold to change speed in large
steps.
Activation of the functionality
Press Ñ to activate speed limiter.
Setting speed by the driver
Adopting speed by the speed limit
recognition
The intelligent speed adaptation
informs the driver when a speed limit
is detected by the speed limit
recognition. The detected speed limit
can be used as new value for the
speed limiter.
Using the camera at the top of the
windscreen, this system detects and
reads speed limit and end of speed
limit signs.
Speed value is indicated in the Driver
Information Centre.
Driving and operating
145
If the speed limiter is active, the
recognised speed limit will be
displayed in the Driver Information
Centre and MEM illuminates.
Press MEM on the steering wheel to
request saving of the suggested
speed limit.
Press MEM on the steering wheel
once more to confirm and save the
new speed setting.
This speed is the new value for the
speed limiter.
This function can be deactivated or
activated in the personalisation menu
3 95.
Deactivation of the functionality
Fault
Press Ñ, speed limiter is in pause
mode and a message is displayed.
The vehicle is driven without speed
limiter.
Speed limiter is deactivated, but not
switched off. Last stored speed
remains in memory for later speed
resume.
In the event of a speed limiter fault,
the speed is cleared resulting in
flashing of the dashes.
The speed limit recognition may not
operate correctly if traffic signs do not
comply with the Vienna Convention
on Road Signs and Signals.
Exceeding the speed limit
Press ß, the speed limiter mode is
deselected and the speed limit
indication extinguishes in the Driver
Information Centre.
Pressing m to activate cruise control
deactivates speed limiter.
The preset speed remains in the
memory when the ignition is switched
off.
In the event of an emergency, it is
possible to exceed the speed limit by
depressing the accelerator pedal
firmly. In this case the preset speed
value flashes.
Release the accelerator pedal and
the speed limiter function is
reactivated once a speed lower than
the limit speed is obtained.
Resume limit speed
Press Ñ. The stored speed limit will
be obtained.
Switching off the system
Forward collision alert
The forward collision alert may help to
avoid or reduce the harm caused by
front-end crashes.
The forward collision alert uses the
front camera in the windscreen to
detect a preceding vehicle directly
ahead, in your path.
If a vehicle directly ahead is
approached too quickly, a warning
chime and alert in the Driver
Information Centre is provided.
9 Warning
Forward collision alert is just a
warning system and does not
apply the brakes. When
146
Driving and operating
approaching a vehicle ahead too
rapidly, it may not provide you
enough time to avoid a collision.
The driver accepts full
responsibility for the appropriate
following distance based on traffic,
weather and visibility conditions.
The complete attention of the
driver is always required while
driving. The driver must always be
ready to take action and apply the
brakes.
Activation
Forward collision alert detects
vehicles and operates automatically
at all speeds between 5 km/h and
85 km/h. The system detects
stationary vehicles if the speed does
not exceed 80 km/h.
Alerting the driver
The driver is warned by following
alerts:
● Symbol , illuminates and a
warning message is displayed in
the Driver Information Centre
when the distance to the vehicle
ahead gets to small.
● Symbol , illuminates, a warning
message is displayed in the
Driver Information Centre and a
warning chime sounds, when a
collision is imminent and
immediate driver's action is
required.
9 Warning
Forward collision alert is just a
warning system and does not
apply the brakes. When
approaching a vehicle ahead too
rapidly, it may not provide you
enough time to avoid a collision.
The driver accepts full
responsibility for the appropriate
following distance based on traffic,
weather and visibility conditions.
The complete attention of the
driver is always required while
driving. The driver must always be
ready to take action and apply the
brakes.
Caution
The colour lighting of this control
indicator does not correspond to
local traffic laws on following
distance. The driver bears full
responsibility for maintaining safe
following distance according to
applicable traffic rules, weather
and road conditions etc. at all
times.
Selecting the alert sensitivity
The alert sensitivity has to be set to
close, normal or distant in the vehicle
personalisation menu 3 95.
Driving and operating
The chosen setting will remain until it
is changed. The alert timing will vary
based on vehicle speed. The faster
the vehicle speed, the farther away
the alert will occur. Consider traffic
and weather conditions when
selecting the alert timing.
●
Deactivation
Active emergency braking
The system can only be deactivated
by deactivating the active emergency
braking in the vehicle personalisation
3 95.
Active emergency braking can help to
reduce the damage and injury from
crashes with vehicles, pedestrians
and obstacles directly ahead, when a
collision can no longer be avoided
either by manual braking or by
steering. Before the active
emergency braking applies, the driver
is warned by the forward collision
alert or the front pedestrian protection
alert.
Forward collision alert 3 145
Front pedestrian protection 3 149
The feature uses various inputs (e.g.
camera sensor, brake pressure,
vehicle speed) to calculate the
probability of a frontal collision.
System limitations
Forward collision alert is designed to
warn on vehicles only, but may react
also to other objects.
In the following cases, forward
collision alert may not detect a vehicle
ahead or sensor performance is
limited:
● driving on winding or hilly roads
● driving in the dark
● weather limits visibility, such as
fog, rain, or snow
●
the sensor in the windscreen is
blocked by snow, ice, slush, mud,
dirt etc.
the windscreen is damaged or
affected by foreign objects, e.g.
stickers
147
9 Warning
This system is not intended to
replace the driver responsibility for
driving the vehicle and looking
ahead. Its function is limited to
supplemental use only to reduce
the vehicle speed before a
collision.
The system may not react to
animals. After a sudden lane
change, the system needs a
certain time to detect the next
preceding vehicle.
The driver must always be ready
to take action and apply the brakes
and steer to avoid collisions.
Functionality
Active emergency braking is
equipped with a front camera and
operates in forward gear above
walking speed up to 85 km/h. The
system detects stationary vehicles
only if the speed does not exceed
80 km/h.
148
Driving and operating
A precondition is that forward collision
alert with front camera system is not
deactivated in the vehicle
personalisation menu 3 95.
The system includes:
● emergency automatic braking
● forward looking brake assist
● forward collision alert
● front pedestrian protection
Emergency automatic braking
After activation of brake preparation
system and just before the imminent
collision, this function automatically
applies limited braking to reduce the
impact speed of the collision or
prohibit a crash. If active emergency
braking is applied, m flashes in the
instrument cluster. Depending on the
situation, the vehicle may
automatically brake moderately or
hard. This front automatic braking can
only occur if a vehicle or a pedestrian
ahead is detected.
Forward collision alert 3 145
Front pedestrian protection 3 149
Emergency automatic braking may
slow the vehicle to a complete stop to
try to avoid a potential crash.
9 Warning
Emergency automatic braking is
an emergency crash preparation
feature and is not designed to
avoid crashes. Do not rely on the
system to brake the vehicle.
Emergency automatic braking will
not brake outside of its operating
speed range and only responds to
detected vehicles and
pedestrians.
Forward looking brake assist
In addition to emergency automatic
braking, the forward looking brake
assist function makes the brake assist
more sensitive. Therefore, pressing
the brake pedal less strongly results
in immediate hard braking. This
function helps the driver brake
quicker and harder before the
imminent collision.
9 Warning
Active emergency braking is not
designed to apply hard
autonomous braking or to
automatically avoid a collision. It is
designed to reduce the vehicle
speed before a collision. It may not
react to animals. After a sudden
lane change, the system needs a
certain time to detect the next
preceding vehicle.
The complete attention of the
driver is always required while
driving. The driver must always be
ready to take action and apply the
brakes and steer to avoid
collisions.
The system is designed to work with
all occupants wearing their seat belts.
Forward collision alert 3 145.
Front pedestrian protection 3 149.
Driving and operating
System limitations
In some cases, the active emergency
braking system may provide an
automatic braking in situations that
seem to be unnecessary, for instance
in parking garages, due to traffic signs
in a curve or due to vehicles in
another lane. This is normal
operation, the vehicle does not need
service. Firmly apply the accelerator
pedal to override the automatic
braking if the situation and the
surroundings permit.
In the following cases, active
emergency braking performance is
limited:
● driving on winding or hilly roads
● detecting all vehicles, especially
vehicles with a trailer, tractors,
muddy vehicles, etc.
● detecting a vehicle when weather
limits visibility, such as in fog,
rain, or snow
● driving in the dark
● windscreen damaged or
stickered
Complete attention is always required
while driving, and you should be
ready to take action and apply the
brakes and / or steer the vehicle to
avoid crashes.
We recommend to deactivate the
system in the vehicle personalisation
in the following cases:
● when towing a trailer or caravan
● when carrying long objects on
roof bars or a roof rack
● when the vehicle is being towed
with the engine running
● when a spare wheel is fitted that
is smaller than the other wheels
● before using an automatic car
wash with the engine running
● before placing the vehicle on a
rolling road in a workshop
● if the windscreen has been
damaged close to the camera
● if the front bumper has been
damaged
● if the brake lamps are not working
Active emergency braking can be
deactivated in the personalisation
menu 3 95. If deactivated, m
149
illuminates in the instrument cluster
and a warning message is displayed
in the Driver Information Centre.
Fault
In case the system requires a service,
a message is displayed in the Driver
Information Centre.
If the system does not work as it
should do, vehicle messages are
displayed in the Driver Information
Centre.
Vehicle messages 3 94.
Front pedestrian protection
Front pedestrian protection may help
to avoid or reduce the harm caused
by front-end crashes with pedestrians
when driving forward.
The system uses the front camera in
the windscreen to detect a pedestrian
directly ahead in your path.
Front pedestrian protection can
detect and alert to pedestrians in a
forward gear at speeds between
5 km/h and 60 km/h.
150
Driving and operating
During driving in the dark, system
performance is limited.
9 Danger
Front pedestrian braking does not
provide an alert or automatically
brake the vehicle, unless it detects
a pedestrian.
The system may not detect
pedestrians, including children,
when the pedestrian is not directly
ahead, not fully visible, not
standing upright, or when part of a
group.
Front pedestrian protection includes:
● detecting front pedestrian ahead
● front pedestrian alert
Front pedestrian protection is
activated together with forward
collision alert.
Forward collision alert 3 145.
Detecting front pedestrian ahead
A pedestrian ahead up to a distance
of approx. 40 m is indicated by a
symbol in the instrument cluster.
Front pedestrian alert
When approaching a detected
pedestrian too quickly, a warning
message is displayed in the Driver
Information Centre. A warning chime
is provided.
Cruise control or Adaptive cruise
control may be disengaged when the
front pedestrian alert occurs.
System limitations
In the following cases, front
pedestrian protection may not detect
a pedestrian ahead or sensor
performance is limited:
● vehicle speed is out of range from
5 km/h to 60 km/h in forward gear
● the distance to an pedestrian
ahead is more than 40 m
● driving on winding or hilly roads
● driving in the dark
● weather limits visibility, such as
fog, rain, or snow
●
●
the sensor in the windscreen is
blocked by snow, ice, slush, mud,
dirt etc.
the windscreen is damaged or
affected by foreign objects, e.g.
stickers
Parking assist
General information
The system is switched off
automatically when attaching a trailer
or bike carrier to the trailer hitch.
9 Warning
The driver bears full responsibility
for the parking manoeuvre.
Always check the surrounding
area when driving backwards or
forwards while using parking
assist system.
The parking assist makes parking
easier by measuring the distance
between the vehicle and obstacles. It
informs and warns the driver by giving
acoustic signals and display
indication.
Driving and operating
Acoustic signals are given on the side
on which the vehicle is closer to an
obstacle. The interval between the
sounds becomes shorter as the
vehicle gets closer to that obstacle.
When the distance is less than
approx. 30 cm, the sound is
continuous.
Rear parking assist
The system operates with ultrasonic
parking sensors in the rear bumper.
Activation
Rear parking assist is activated when
reverse gear is engaged.
The system is ready to operate when
the LED in the parking assist button
¼ is not illuminated.
151
Deactivation
Indication
The system warns the driver with
acoustic signals against potentially
hazardous obstacles behind the
vehicle in a distance range up to
50 cm.
Additionally, the distance to rear
obstacles is displayed by changing
distance lines in the Info Display
3 90. When the obstacle is very close,
9 for danger is displayed in the
screen.
The system is switched off when
reverse gear is disengaged. Press ¼
to deactivate the system manually.
The LED in the button illuminates
when the system is deactivated. If the
system has been deactivated
manually, it is not reactivated
automatically the next time the
ignition is switched on.
Front-rear parking assist
It uses two different acoustic warning
signals for the front and rear
monitoring areas, each with a
different tone frequency.
152
Driving and operating
Indication
The system warns the driver with
acoustic signals against potentially
hazardous obstacles in front of the
vehicle and behind the vehicle by
using the respective loudspeakers.
The system operates with ultrasonic
parking sensors in the rear and front
bumper.
Activation
Rear parking assist is activated when
reverse gear is engaged.
In addition to the rear parking assist,
the front parking assist is triggered
when an obstacle is detected in front
and the speed of the vehicle is still
below 10 km/h.
The system is ready to operate when
the LED in the parking assist button
¼ is not illuminated.
Additionally, the distance to rear and
front obstacles is displayed by
changing distance lines in the Info
Display 3 90.
Deactivation
The system is deactivated
automatically when vehicle speed
exceeds 10 km/h or if the vehicle
stops for more than 3 seconds in a
forward gear or if no further obstacles
are detected.
When the system is deactivated
manually, the LED in the button
illuminates.
If the system has been deactivated
manually, it is not reactivated
automatically the next time the
ignition is switched on.
Driving and operating
System limitations
In the event of a fault or if the system
does not work temporarily, e.g.
because of high external noise level
or other interference factors, Service
in the cluster instrument illuminates.
A message is indicated in the Driver
Information Centre.
9 Warning
Under certain circumstances,
various reflective surfaces on
objects or clothing as well as
external noise sources may cause
the system to fail to detect
obstacles.
Special attention must be paid to
low obstacles which can damage
the lower part of the bumper.
Caution
Performance of the system can be
reduced when sensors are
covered, e.g. by ice or snow.
Performance of the parking assist
system can be reduced due to
heavy loading.
Special conditions apply if there
are taller vehicles in the vicinity
(e.g. off-road vehicles, mini vans,
vans). Object identification and
correct distance indication in the
upper part of these vehicles
cannot be guaranteed.
Objects with a very small reflection
cross-section, e.g. objects of
narrow size or soft materials, may
not be detected by the system.
Parking assist systems do not
detect objects outside the
detection range.
Note
Make sure that the front number
plate is properly mounted (not bent
and no gaps to the bumper on the left
or right side) and the sensors are
firmly in place.
153
Advanced parking assist
9 Warning
The driver bears full responsibility
for accepting the parking slot
suggested by the system and the
parking manoeuvre.
Always check the surrounding
area in all directions when using
the advanced parking assist.
The advanced parking assist
measures a suitable parking slot
while passing, calculates the
trajectory and automatically steers
the vehicle while parking.
Advanced parking assist provides
assistance for the following
manoeuvres:
● entry into a parallel parking slot
● entry into a perpendicular parking
slot
● exit from a parallel parking slot
154
Driving and operating
The driver must control acceleration,
braking and gear shifting, while
steering is done automatically. The
driver can take control at any time by
gripping the steering wheel.
It may be necessary to move forwards
and backwards more than once.
Instructions are given in the Info
Display 3 90.
Advanced parking assist can only be
activated when driving forwards.
Advanced parking assist is always
combined with front-rear parking
assist.
The system has six ultrasonic parking
sensors each in both the rear and
front bumper.
The system will not identify slots that
are clearly smaller or larger than the
vehicle.
Entry into a parallel parking slot
Activation
7'' Colour Info Display: to search for a
parking slot, activate the system by
selecting Park Assist on the
homepage of the touch screen. Then
select Enter parallel parking space.
8'' Colour Info Display: to search for a
parking slot, activate the system by
pressing Í. Select Driving functions
on the touch screen and then Park
Assist. Select Enter parallel parking
space.
$ illuminates in the instrument cluster
to confirm the function.
Slow down the vehicle speed below
20 km/h.
Select parking side by switching on
turn light indicator on the respective
side.
The allowed parallel distance
between the vehicle and a row of
parked cars is between 0.5 m and
1.5 m.
When a free slot is detected, a visual
feedback on the Colour Info Display
and a first acoustic signal is given.
Drive slowly forwards. When the
second acoustic signal is given, stop
the vehicle, select reverse gear,
release the steering wheel and start
moving without exceeding 7 km/h.
Driving and operating
Move forwards and backwards while
observing the warnings of the parking
assist until the end of manoeuvre is
indicated. When finished, $
extinguishes in the instrument cluster.
Entry into a perpendicular parking
slot
Activation
7'' Colour Info Display: to search for a
parking slot, activate the system by
selecting Park Assist on the
homepage of the touch screen. Then
select Enter perpendicular parking
space.
8'' Colour Info Display: when search
for a parking slot, activate the system
by pressing Í. Select Driving
functions on the touch screen and
then Park Assist. Select Enter bay
parking space.
$ illuminates in the instrument cluster
to confirm the function.
Slow down the vehicle speed below
20 km/h.
Select parking side by switching on
turn light indicator on the respective
side.
The allowed parallel distance
between the vehicle and a row of
parked cars is between 0.5 m and
1.5 m.
When several successive slots are
found, the vehicle will be directed
towards the last one.
155
When a free slot is detected, a visual
feedback on the Colour Info Display
and an acoustic signal is given. Stop
the vehicle, select reverse gear,
release the steering wheel and start
moving without exceeding 7 km/h.
156
Driving and operating
Exiting a parallel parking slot
Move forwards and backwards as
instructed by observing the warnings
of the parking assist and paying
attention to the acoustic signals until
the end of manoeuvre is indicated.
When finished, $ extinguishes in the
instrument cluster.
During the parking manoeuvre, the
system is automatically deactivated
once the rear of the vehicle is within
50 cm of an obstacle.
Activation
7'' Colour Info Display: when exiting a
parallel parking slot, activate the
system by selecting Park Assist on
the homepage of the touch screen.
Then select Exit parallel parking
space.
8'' Colour Info Display: when exiting a
parallel parking slot, activate the
system by pressing Í. Select Driving
functions on the touch screen and
then Park Assist. Select Exit parallel
parking space.
Select exit side by switching on the
respective turn light indicator.
Engage reverse or forward gear,
release the steering wheel and start
moving without exceeding 5 km/h.
Move forwards and backwards while
observing the warnings of the parking
assist until the end of manoeuvre is
indicated. The manoeuvre is
complete when the vehicle's front
wheels are out of the parking slot and
$ extinguishes in the instrument
cluster.
After deactivation check control over
the vehicle.
Driving and operating
Display indication
The instructions on the display show:
● general hints and warning
messages
● the demand to stop the vehicle,
when a parking slot is detected
● the direction of driving during the
parking manoeuvre
● the demand to shift into reverse
or first gear
● the demand to stop or to drive
slowly
● the successful completion of the
parking manoeuvre indicated by
a pop-up symbol and a chime
● the cancelling of a parking
manoeuvre
Deactivation
The current park assist manoeuvre is
cancelled via the button to return to
the previous screen in the Colour Info
Display. To deactivate the system
completely, press r Off in the
centre console.
The system is deactivated
automatically:
● if the ignition is switched off
● if stalling the engine
● if no manoeuvre is started within
5 minutes of selection of the type
of manoeuvre
● after a prolonged stop of the
vehicle during a manoeuvre
● if the electronic stability control is
triggered
● if the speed of the vehicle
exceeds the stated limit
● when the driver interrupts
movement of the steering wheel
● after four manoeuvre cycles
● on opening the driver's door
● if one of the front wheels
encounters an obstacle
● parking manoeuvre successfully
ended
Deactivation by the driver or by the
system during manoeuvring will be
indicated on the display. Additionally,
an acoustic signal sounds.
157
The system is switched off
automatically when attaching a trailer
or bike carrier to the trailer hitch.
Contact your dealer to switch off the
system for a prolonged period.
Fault
In the event of a fault, $ flashes for a
few seconds, accompanied by an
acoustic signal. If the fault occurs
during the use of the system, $
extinguishes.
In the event of a fault in the power
steering, c flashes in the instrument
panel, accompanied by a message.
Note
It is possible that the sensor detects
a non-existing object caused by
echo disturbance from external
acoustic noise or mechanical
misalignments (sporadic false
warnings may occur).
Advanced parking assist system
may not respond to changes in the
available parking space after
initiating a parking manoeuvre. The
system may recognise an entry, a
gateway, a courtyard or even a
158
Driving and operating
crossing as a parking slot. After
selecting reverse gear the system
will start a parking manoeuvre. Take
care regarding the availability of the
suggested parking slot.
Low curbs and surface irregularities,
e.g. on construction zones, are not
detected by the system. The driver
accepts responsibility.
Side blind spot alert
The side blind spot alert system
detects and reports objects on either
side of the vehicle, within a specified
blind spot zone. The system displays
a visual alert in each exterior mirror,
when detecting objects that may not
be visible in the interior and exterior
mirrors.
Side blind spot alert uses some of the
parking assist sensors.
9 Warning
Side blind spot alert does not
replace driver vision.
The system does not detect:
●
vehicles outside the side blind
zones which may be rapidly
approaching
● pedestrians, cyclists or animals
Before changing a lane, always
check all mirrors, look over the
shoulder and use the turn light.
Functionality
Activation
7'' Colour Info Display: select Blind
spot monitoring on the Info Display
and activate the function.
8'' Colour Info Display: press Í.
Select Driving functions on the Info
Display and then Blind spot
monitoring. Activate the function.
B illuminates continously green in the
instrument cluster to confirm the
function.
When the system detects a vehicle in
the side blind zone while driving
forwards, an LED will illuminate in the
relevant exterior mirror.
The LED comes on immediately when
being passed.
The LED comes on after a delay when
passing another vehicle slowly.
Driving and operating
Operation conditions
The following conditions must be
fulfilled for proper operation:
● all vehicles are moving in the
same direction and in adjacent
lanes
● the vehicle speed is between 12
and 140 km/h
● passing a vehicle with a speed
difference of less than 10 km/h
● another vehicle is passing with a
speed difference of less than
25 km/h
● the traffic flow is normal
● driving on a straight or slightly
curved road
No alert will be given in the following
situations:
● in the presence of non-moving
objects, e.g. parked vehicles,
barriers, street lamps, road signs
● with vehicles moving in the
opposite direction
● driving on a winding road or a
sharp corner
●
●
●
when passing or being passed by
a very long vehicle, e.g. lorry,
coach, which is at the same time
detected at the rear in the blind
spot angle and present in the
driver's forward field of vision
in very heavy traffic: vehicles
detected in front and behind are
confused with a lorry or a
stationary object
when passing too quickly
Deactivation
The system is deactivated in the
vehicle personalisation 3 95. B
extinguishes in the instrument cluster.
Additionally, an acoustic signal
sounds.
The state of the system is stored
when switching off the ignition.
The system is switched off
automatically when attaching a trailer
or bike carrier to the trailer hitch.
Due to adverse weather conditions
such as heavy rain, false detections
may occur.
159
Fault
In the event of a fault, B flashes for a
few moments in the instrument
cluster, accompanied by C and a
display message. Seek the
assistance of a workshop.
Panoramic view system
This system allows views of the
vehicle's surroundings to be
displayed as a nearly 180° picture in
the Info Display, like a bird's eye view.
The system uses:
● rear camera, installed in the
tailgate
● ultrasonic parking sensors in the
rear bumper
The screen is divided into two parts:
on the right there is a view from above
the vehicle, and on the left there are
different views displayed.
160
Driving and operating
Activation
Panoramic view system is activated
by:
● engaging reverse gear
● driving up to 10 km/h
Functionality
● zoom view
● 180° view
Auto mode is activated by default. In
this mode, the system selects the
best view, standard or zoom, to
display according to the information
from the parking sensors.
The state of the system is not kept in
memory when the ignition is switched
off.
Rear view
Different views can be selected in the
left part of the display. Change the
type of view by pressing the touch
field in the left lower zone of the
display:
● rear view
● auto mode
The area behind the vehicle is
displayed in the screen. The vertical
lines represent the width of the
vehicle with mirrors unfolded. The
direction of the lines changes with the
steering angle.
The horizontal lines represent a
distance of about 30 cm, 1m and 2 m
beyond the rear bumper.
This view is available in auto mode or
in the view selection menu.
Auto mode
This mode is activated by default.
Using sensors in the rear bumper, the
automatic view changes from a rear
view to a view from above, as an
obstacle is approached during a
manoeuvre.
Driving and operating
Zoom view
180° view
161
Deactivation
Panoramic view system is
deactivated when:
● driving faster than 10 km/h
● 7 seconds after disengaging
reverse gear
● by pressing the icon q in the left
upper corner of the touch screen
● opening the tailgate
General information
The camera records the vehicle's
surroundings during the manoeuvre
in order to reconstruct a view from
above the rear of the vehicle in its
near surroundings, allowing the
vehicle to be manoeuvred around
obstacles nearby. This view is
available with auto mode or in the
view selection menu.
The 180° view facilitates reversing
out of a parking bay, making it
possible to see the approach of
vehicles, pedestrians and cyclists.
This view is not recommended for
carrying out a complete manoeuvre.
It is made up of three areas: left 1,
centre 2 and right 3. This view is
available from the view selection
menu only.
9 Warning
The panoramic view system does
not replace driver vision. It will not
display children, pedestrians,
cyclists, crossing traffic, animals,
or any other objects outside of the
camera view area, e. g. below the
bumper, or underneath the
vehicle.
Do not drive or park the vehicle
using only the panoramic view
system.
Always check the surrounding of
the vehicle before driving.
162
Driving and operating
Displayed images may be further
or closer than they appear. The
area displayed is limited and
objects that are close to either
edge of the bumper or under the
bumper are not displayed on the
screen.
System limitations
Caution
●
●
●
●
●
●
During nighttime driving.
Weather limits visibility, such as
fog, rain, or snow.
The camera lenses are blocked
by snow, ice, slush, mud, dirt.
A trailer or bike carrier is attached
to the trailer hitch.
The vehicle had an accident.
There are extreme temperature
changes.
Do not reverse or park the vehicle
using only the rear view camera.
Always check the surrounding of
the vehicle before driving.
Switching on
Rear view camera is automatically
activated when reverse gear is
engaged.
Functionality
Rear view camera
For optimal operation of the
system, it is important to keep the
lense of the camera in the tailgate
between the number plate lights
always clean. Rinse the lense with
water and wipe with a soft cloth.
Do not clean the lense with a
steam-jet or high-pressure jet
cleaner.
The rear view camera assists the
driver when reversing by displaying a
view of the area behind the vehicle.
The view of the camera is displayed
in the Info Display.
The panoramic view system may not
operate properly when:
● The surrounding is dark.
● The sun or the beam of
headlights is shining directly into
the camera lenses.
The rear view camera does not
replace driver vision. Note that
objects that are outside the
camera's field of view and the
parking assist sensors, e.g. below
the bumper or underneath the
vehicle, are not displayed.
9 Warning
The area displayed by the camera is
limited. The distance of the image that
appears on the display differs from
the actual distance.
Driving and operating
Guide lines
Switching off
Lane departure warning
The camera is switched off when a
certain forward speed is exceeded or
if reverse gear is disengaged for
approx. 10 seconds.
The lane departure warning system
observes the lane markings between
which the vehicle is driving via a front
camera. The system detects lane
changes and warns the driver in the
event of an unintended lane change
via visual and acoustic signals.
Criteria for the detection of an
unintended lane change are:
● no operation of turn lights
● no brake pedal operation
● no active acceleration
If the driver is active, no warning will
be issued.
System limitations
The vertical lines represent the width
of the vehicle without mirrors and the
general direction of the vehicle. The
horizontal lines represent a distance
of about 30 cm, 1m and 2 m beyond
the rear bumper. The crossing curves
represent the maximum turning circle.
Deactivation of guide lines
Guide lines can be deactivated in the
Info Display. Select Settings I Vehicle
I Collision detection I Rear view
camera guide lines I §.
Info Display 3 90.
Vehicle personalisation 3 95.
163
The rear view camera may not
operate properly when:
● The surrounding is dark.
● The beam of headlights is shining
directly into the camera lenses.
● During nighttime driving.
● Weather limits visibility, such as
fog, rain, or snow.
● The camera lenses are blocked
by snow, ice, slush, mud, dirt.
Clean the lense, rinse with water,
and wipe with a soft cloth.
● The tailgate will be opened.
● A trailer or bike carrier is attached
to the trailer hitch.
● The vehicle had a rear end
accident.
● There are extreme temperature
changes.
164
Driving and operating
Activation
●
●
●
Deactivation
The system is deactivated by
pressing ½, the LED in the button
illuminates.
At speeds below 60 km/h the system
is inoperable.
The lane departure warning system is
activated by pressing ½. The system
is switched on when the LED in the
button is not illuminated.
The system is only operable at
vehicle speeds above 60 km/h and if
lane markings are available.
When the system recognises an
unintended lane change, the control
indicator ) flashes yellow.
Simultaneously a chime sound is
activated.
Fault
In the event of a fault, C appears in
the instrument cluster, accompanied
by a display message. Seek the
assistance of a workshop.
The system cannot operate when no
lane marking is detected.
System limitations
The system may not operate properly
when:
● vehicle speed is below 60 km/h
● driving on winding or hilly roads
●
●
●
●
●
●
driving in the dark
weather limits visibility, such as
fog, rain, or snow
the camera is blocked by snow,
ice, slush, mud, dirt, windscreen
damage or affected by foreign
items, e.g. stickers
the sun is shining directly into the
camera lens
close vehicles ahead
banked roads
road edges
roads with poor lane markings
sudden lighting changes
Driver alert
9 Warning
The system cannot replace the
need for vigilance on the part of
the driver. Taking a break is
recommended as soon as feeling
tired or at least every two hours.
Do not take the steering wheel
when feeling tired.
Driving and operating
Activation or Deactivation
The system can be activated or
deactivated in the vehicle
personalisation 3 95.
The state of the system stays in
memory when the ignition is switched
off.
Driving time alert
The driver gets notified by a pop-up
reminder symbol € in the Driver
Information Centre simultaneously
with an acoustic alert if the driver has
not taken a break after 2 hours of
driving at a speed above 65 km/h. The
alert is repeated hourly until the
vehicle is stopped, no matter how
vehicle speed evolves.
The counting of driving time alert is
reset when the ignition has been
switched off for a few minutes.
Driver drowsiness detection
The system monitors the driver's level
of vigilance. A camera in the
windscreen detects variations in
trajectory compared to the lane
markings. This system is particularly
suited for a speed higher than
65 km/h.
If the trajectory of the vehicle
suggests a certain level of
drowsiness or inattention by the
driver, the system triggers the first
level of alert. The driver is notified by
a message and an audible signal is
given.
After three first level alerts, the
system triggers a new alert with a
message, accompanied by a more
pronounced audible signal.
In certain driving conditions (poor
road surface or strong winds), the
system may give alerts independent
of the driver's level of vigilance.
The driver drowsiness detection is
reinitialised when the ignition has
been switched off for a few minutes or
the speed remains below 65 km/h for
a few minutes.
165
System limitations
The system may not operate properly
when:
● dazzle caused by headlamps of
an oncoming vehicles, low sun,
reflections on damp roads
● driving on winding, hilly or narrow
roads
● driving in the dark
● weather limits visibility, such as
fog, rain, or snow
● the camera is blocked by snow,
ice, slush, mud, dirt
● the windscreen is damaged or
affected by foreign items, e.g.
stickers
● the sun is shining directly into the
camera lens
● close vehicles ahead
● banked roads
● road edges
● roads with poor lane markings
● multiple lane markings due to
roadworks
● sudden lighting changes
166
Driving and operating
Fuel
Fuel for petrol engines
The petrol engines are compatible
with bio-fuels that conform to current
and future European standards and
and can be obtained from filling
stations:
Caution
Use of fuel with a lower octane
rating than the lowest possible
rating could lead to uncontrolled
combustion and engine damage.
The engine-specific requirements
regarding octane rating are given in
the engine data overview 3 226. A
country-specific label at the fuel filler
flap can supersede the requirement.
Fuel for diesel engines
Petrol that meets the EN228
standard, mixed with a biofuel
meeting the EN15376 standard.
Use fuel with the recommended
octane rating. A lower octane rating
can reduce engine power and torque
and slightly increases fuel
consumption.
The diesel engines are compatible
with bio-fuels that conform to current
and future European standards and
can be obtained from filling stations:
Diesel fuel that meets standard
EN590 mixed with a biofuel that
meets standard EN14214 (possibly
containing up to 7% Fatty Acid Methyl
Ester).
Diesel fuel that meets standard
EN16734 mixed with a biofuel that
meets standard EN14214 (possibly
containing up to 10% Fatty Acid
Methyl Ester).
Paraffinic diesel fuel that meets
standard EN15940 mixed with a
biofuel that meets standard
EN14214 (possibly containing up to
7% Fatty Acid Methyl Ester).
Driving and operating
Low temperature operation
The use of B20 or B30 fuel meeting
standard EN16709 is possible.
However, this use, even occasional,
requires strict application of the
special servicing conditions referred
to as "arduous conditions".
For further information, contact a
workshop.
Caution
The use of any other type of (bio)
fuel (vegetable or animal oils, pure
or diluted, domestic fuel etc.) is
strictly prohibited (risk of damage
to the engine and fuel system).
Note
The only diesel additives authorised
for use are those that meet the
B715000 standard.
At temperatures below 0 °C, some
diesel products with biodiesel blends
may clog, freeze or gel, which may
affect the fuel supply system. Starting
and engine operation may not work
properly. Make sure to fill winter
grade diesel fuel at ambient
temperatures below 0 °C.
Arctic grade diesel fuel can be used
in extreme cold temperatures below
-20 °C. Using this fuel grade in warm
or hot climates is not recommended
and may cause engine stalling, poor
starting or damage on the fuel
injection system.
167
Refuelling
9 Danger
Before refuelling, switch off
ignition and any external heaters
with combustion chambers.
Follow the operating and safety
instructions of the filling station
when refuelling.
168
Driving and operating
9 Danger
Fuel is flammable and explosive.
No smoking. No naked flames or
sparks.
If you can smell fuel in your
vehicle, have the cause of this
remedied immediately by a
workshop.
A label with symbols at the fuel filler
flap is indicating the allowed fuel
types. In Europe the pump nozzles of
the filling stations are marked with
these symbols. Refuel only the
allowed fuel type.
Caution
In case of misfuelling, do not
switch on ignition.
Fuel filler flap is located at left rear
side of vehicle.
The fuel filler flap can only be opened
if the vehicle is unlocked. Release the
fuel filler flap by pushing the flap.
Petrol and diesel refuelling
To open, turn the cap slowly
anticlockwise.
The fuel filler cap can be attached to
the hook on the fuel filler flap.
Place the nozzle in straight position to
the filler neck and press with slight
force to insert.
To refuel, switch on pump nozzle.
After the automatic cut-off, the tank
can be topped up by operating the
pump nozzle a maximum of two more
times.
Caution
Wipe off any overflowing fuel
immediately.
Driving and operating
To close, turn the fuel filler cap
clockwise.
Close the flap and allow it to engage.
Fuel filler cap
Only use genuine fuel filler caps.
Diesel-engined vehicles have special
fuel filler caps.
Trailer hitch
General information
Entrust retrofitting of towing
equipment to a workshop. It may be
necessary to make changes that
affect the cooling system, heat
shields or other equipment. Only use
approved towing equipment.
The bulb outage detection function for
trailer or bike carrier brake light
cannot detect a partial bulb outage.
E.g. in case of four bulbs with a power
of 5 W each, the function only detects
lamp outage when only a single 5 W
lamp remains or none remain.
LED lights are not suitable for the
wiring harness of this trailer hitch.
Towing equipment could cover the
opening of the towing eye. If this is the
case use the coupling ball bar for
towing.
169
Driving characteristics and
towing tips
Before attaching a trailer, lubricate
the coupling ball. However, do not do
so if a stabiliser, which acts on the
coupling ball, is being used to reduce
snaking movements.
During trailer towing do not exceed a
speed of 80 km/h. A maximum speed
of 100 km/h is only appropriate if an
oscillation damper is used and the
permissible gross trailer weight does
not exceed the vehicle’s curb weight.
For trailers with low driving stability
and caravan trailers, the use of an
oscillation damper is strongly
recommended.
If the trailer starts snaking, drive more
slowly, do not attempt to correct the
steering and brake sharply if
necessary.
When driving downhill, drive in the
same gear as if driving uphill and
drive at a similar speed.
Adjust tyre pressure to the value
specified for full load 3 230.
170
Driving and operating
Trailer towing
Trailer loads
The permissible trailer loads are
vehicle and engine-dependent
maximum values which must not be
exceeded. The actual trailer load is
the difference between the actual
gross weight of the trailer and the
actual coupling socket load with the
trailer coupled.
The permissible trailer loads are
specified in the vehicle documents. In
general, they are valid for inclines up
to 12%.
The permissible trailer load applies
up to the specified incline and at sea
level. Since engine power decreases
as altitude increases due to the air
becoming thinner, therefore reducing
climbing ability, the permissible gross
train weight also decreases by 10%
for every 1000 m of altitude. The
gross train weight does not have to be
reduced when driving on roads with
slight inclines (less than 8%, e.g.
motorways).
The permissible gross train weight
must not be exceeded. This weight is
specified on the identification plate
3 221.
Vertical coupling load
The vertical coupling load is the load
exerted by the trailer on the coupling
ball. It can be varied by changing the
weight distribution when loading the
trailer.
The maximum permissible vertical
coupling load of 65 kg is specified on
the towing equipment identification
plate and in the vehicle documents.
For vehicles with engine DV5RC and
automatic transmission, the
maximum permissible vertical
coupling load is 55 kg. Always aim for
the maximum load, especially in the
case of heavy trailers. The vertical
coupling load should never fall below
25 kg.
Rear axle load
When the trailer is coupled and the
towing vehicle fully loaded, the
permissible rear axle load (see
identification plate or vehicle
documents) may be exceeded by
60 kg, the gross vehicle weight rating
must not be exceeded. If the
permissible rear axle load is
exceeded, a maximum speed of
100 km/h applies.
Towing equipment
Caution
When operating without a trailer,
remove the coupling ball bar.
Stowage of coupling ball bar
The bag with the coupling ball bar is
stowed on the rear floor cover in the
load compartment.
Driving and operating
Swivel the connecting socket
downwards. Remove the sealing plug
from the opening for the coupling ball
bar and stow it.
Place the strap through the rear right
lashing eye, wrap around twice and
tighten the strap to secure the bag.
Fitting the coupling ball bar
Checking the tensioning of the
coupling ball bar
● Red marking on rotary knob must
point towards green marking on
coupling ball bar.
● The gap between the rotary knob
and the coupling ball bar must be
approx. 6 mm.
● The key must be in position c.
Otherwise, the coupling ball bar must
be tensioned before being inserted:
171
●
Unlock coupling ball bar by
turning key to position c.
●
Pull out rotary knob and turn
clockwise as far as it will go.
172
Driving and operating
Inserting the coupling ball bar
Eye for break-away stopping cable
9 Warning
Towing a trailer is permitted only
when a coupling ball bar is fitted
correctly. If the coupling ball bar
does not engage correctly, seek
the assistance of a workshop.
Dismounting the coupling ball bar
Insert the tensioned coupling ball bar
in the opening and push firmly
upwards until it audibly engages.
The rotary handle snaps back into its
original position resting against the
coupling ball bar without a gap.
9 Warning
Do not touch rotary handle during
insertion.
Lock the coupling ball bar by turning
the key to position c. Remove the key
and close the protective flap.
Attach breakaway stopping cable to
eye.
Checking the correct installation of
the coupling ball bar
● Green marking on rotary knob
must point towards green
marking on coupling ball bar.
● There must be no gap between
the rotary handle and the
coupling ball bar.
● The coupling ball bar must be
firmly engaged in the opening.
● The coupling ball bar must be
locked and the key removed.
Open the protective flap and turn the
key to position c to unlock the
coupling ball bar.
Pull out rotary handle and turn
clockwise as far as it will go. Pull out
coupling ball bar downwards.
Insert sealing plug in opening.
Driving and operating
Swivel the connecting socket
upwards.
Stow the coupling ball bar in the bag
and secure by fixing the strap through
the rear right lashing eye. Wrap
around twice and tighten the strap to
secure the bag.
173
174
Vehicle care
Vehicle care
General Information ................... 174
Accessories and vehicle
modifications .......................... 174
Vehicle storage ........................ 175
End-of-life vehicle recovery ..... 175
Vehicle checks ........................... 176
Performing work ...................... 176
Bonnet ..................................... 176
Engine oil ................................. 177
Engine coolant ......................... 178
Washer fluid ............................ 178
Brakes ..................................... 179
Brake fluid ............................... 179
Vehicle battery ......................... 179
Diesel fuel system bleeding ..... 181
Wiper blade replacement ........ 181
Bulb replacement ....................... 182
Halogen headlights .................. 182
LED headlights ........................ 185
Front fog lights ......................... 185
Tail lights ................................. 185
Side turn lights ......................... 189
Number plate light ................... 190
Interior lights ............................ 190
Electrical system ........................ 190
Fuses ....................................... 190
Engine compartment fuse box . 191
Instrument panel fuse box ....... 192
Vehicle tools .............................. 194
Tools ........................................ 194
Wheels and tyres ....................... 195
Winter tyres ............................. 195
Tyre designations .................... 195
Tyre pressure .......................... 196
Tyre deflation detection
system .................................... 197
Tread depth ............................. 198
Changing tyre and wheel size . 198
Wheel covers ........................... 198
Tyre chains .............................. 199
Tyre repair kit .......................... 199
Wheel changing ....................... 202
Spare wheel ............................ 203
Jump starting ............................. 207
Towing ....................................... 208
Towing the vehicle ................... 208
Towing another vehicle ........... 209
Appearance care ....................... 210
Exterior care ............................ 210
Interior care ............................. 212
Floor mats ............................... 213
General Information
Accessories and vehicle
modifications
We recommend the use of genuine
parts and accessories and factory
approved parts specific for this
vehicle type. We cannot assess or
guarantee reliability of other products
- even if they have a regulatory or
otherwise granted approval.
Any modification, conversion or other
changes made to standard vehicle
specifications (including, without
limitation, software modifications,
modifications of the electronic control
units) may invalidate the warranty
offered by Opel.
Any modification, conversion or other
changes made to standard vehicle
specifications (including, without
limitation, software modifications,
modifications of the electronic control
units) may invalidate the warranty
offered by Vauxhall.
Furthermore, such changes may
affect driver assistance systems, may
impact fuel consumption, CO2
Vehicle care
emissions and other emissions of the
vehicle and cause the vehicle to no
longer conform to the operating
permit, impacting the validity of your
vehicle registration.
Caution
When transporting the vehicle on
a train or on a recovery vehicle, the
mud flaps might be damaged.
Vehicle storage
Storage for a long period of time
If the vehicle is to be stored for several
months:
● Wash and wax the vehicle.
● Have the wax in the engine
compartment and underbody
checked.
● Clean and preserve the rubber
seals.
● Fill up fuel tank completely.
● Change the engine oil.
● Drain the washer fluid reservoir.
●
Check the coolant antifreeze and
corrosion protection.
● Adjust tyre pressure to the value
specified for full load.
● Park the vehicle in a dry, well
ventilated place. Prevent the
vehicle from rolling.
● Engage first or reverse gear or
set selector lever to P.
● Do not apply the parking brake.
● Open the bonnet, close all doors
and lock the vehicle.
● Disconnect the clamp from the
negative terminal of the vehicle
battery. Note that all systems are
not functional, e.g. central locking
system.
Anti-theft alarm system 3 31.
Putting back into operation
When the vehicle is to be put back into
operation:
● Connect the clamp to the
negative terminal of the vehicle
battery. Initialize the power
windows 3 36.
● Check tyre pressure.
●
●
●
●
175
Fill up the washer fluid reservoir.
Check the engine oil level.
Check the coolant level.
Fit the number plate if necessary.
End-of-life vehicle recovery
Information on end-of-life vehicle
recovery centres and the recycling of
end-of-life vehicles is available on our
website, where legally required. Only
entrust this work to an authorised
recycling centre.
176
Vehicle care
Vehicle checks
Performing work
9 Danger
The ignition system uses
extremely high voltage. Do not
touch.
Bonnet
Opening
Open the driver's door.
Move the safety catch sideways to the
left vehicle side and open the bonnet.
The bonnet is held open
automatically.
9 Warning
Closing
Lower the bonnet and let it fall into the
latch from a low height (20-25 cm).
Check that the bonnet is engaged.
Only perform engine compartment
checks when the ignition is off.
The cooling fan may start
operating even if the ignition is off.
Pull the lever and return it to its
original position.
Caution
Do not press the bonnet into the
latch to avoid dents.
Vehicle care
Engine oil
Check the engine oil level manually
on a regular basis to prevent damage
to the engine. Ensure that the correct
specification of engine oil is used.
Recommended fluids and lubricants
3 219.
The maximum engine oil
consumption is 0.6 l per 1000 km.
Check with the vehicle on a level
surface. The engine must be at
operating temperature and switched
off for at least 5 minutes.
Caution
It is the owner's responsibility to
maintain the proper level of an
appropriate quality oil in the
engine.
177
Different dipsticks are used
depending on engine variant.
When the engine oil level has
dropped to the MIN mark, top up the
engine oil. We recommend the use of
the same grade of engine oil that was
used at last change.
Pull out the dipstick, wipe it clean,
reinsert it fully, pull out and read the
engine oil level.
The engine oil level must not exceed
the MAX mark on the dipstick.
178
Vehicle care
the coolant concentration checked
and have the cause of the coolant
loss remedied by a workshop.
Caution
Overfilled engine oil must be
drained or suctioned out. If the oil
exceeds the maximum level, do
not start the vehicle and contact a
workshop.
Washer fluid
Capacities 3 229.
Fit the cap on straight and tighten it.
Engine coolant
The factory filled coolant provides
freeze protection down to approx.
-37 °C.
Caution
Only use approved antifreeze.
Coolant and antifreeze 3 219.
Coolant level
Caution
Too low a coolant level can cause
engine damage.
If the cooling system is cold, the
coolant level should be above the
MIN mark. Top up if the level is low.
9 Warning
Allow the engine to cool before
opening the cap. Carefully open
the cap, relieving the pressure
slowly.
To top up, use a 1:1 mixture of
released coolant concentrate mixed
with clean tap water. If no coolant
concentrate is available, use clean
tap water. Install the cap tightly. Have
Fill with clean water mixed with a
suitable quantity of approved
windscreen washer fluid which
contains antifreeze.
Vehicle care
179
Caution
Only washer fluid with a sufficient
antifreeze concentration provides
protection at low temperatures or
a sudden drop in temperature.
Washer fluid 3 219.
Brakes
In the event of minimum thickness of
the brake lining, a squealing noise
sounds during braking.
Continued driving is possible but
have the brake lining replaced as
soon as possible.
Once new brake linings are installed,
do not brake unnecessarily hard for
the first few journeys.
Brake fluid
9 Warning
Brake fluid is poisonous and
corrosive. Avoid contact with eyes,
skin, fabrics and painted surfaces.
The brake fluid level must be between
the MIN and MAX marks.
If fluid level is below MIN seek the
assistance of a workshop.
Brake fluid 3 219.
Vehicle battery
The vehicle battery is maintenancefree provided that the driving profile
allows sufficient charging of the
battery. Short-distance-driving and
frequent engine starts can discharge
the battery. Avoid the use of
unnecessary electrical consumers.
Batteries do not belong in household
waste. They must be disposed of at
an appropriate recycling collection
point.
Laying up the vehicle for more than
four weeks can lead to battery
discharge. Disconnect the clamp from
the negative terminal of the vehicle
battery.
Ensure the ignition is switched off
before connecting or disconnecting
the vehicle battery.
Battery discharge protection 3 108.
Anti-theft alarm system 3 31.
Replacing the vehicle battery
Note
Any deviation from the instructions
given in this section may lead to
temporary deactivation or
disturbance of the stop-start system.
180
Vehicle care
When the vehicle battery is being
replaced, ensure that there are no
open ventilation holes in the vicinity of
the positive terminal. If a ventilation
hole is open in this area, it must be
closed off with a dummy cap, and the
ventilation in the vicinity of the
negative terminal must be opened.
Ensure that the vehicle battery is
always replaced by the same type of
battery.
The vehicle battery has to be
replaced by a workshop.
Stop-start system 3 126.
Discharge protection
Charging the vehicle battery
Idle boost
If charging of the vehicle battery is
required due to battery condition, the
power output of the generator must
be increased. This will be achieved by
an idle boost which may be audible.
A message appears in the Driver
Information Centre.
9 Warning
On vehicles with stop-start
system, ensure that the charging
potential does not exceed 14.6 V
when using a battery charger.
Otherwise the vehicle battery may
be damaged.
Jump starting 3 207.
Battery voltage
When the vehicle battery voltage is
running low, a warning message will
appear in the Driver Information
Centre.
When the vehicle is being driven, the
load reduction function temporarily
deactivates certain functions, e.g. the
heated rear window.
The deactivated functions are
reactivated automatically as soon as
conditions permit.
Power outlet
The power outlets are deactivated in
the event of low vehicle battery
voltage.
Warning label
Meaning of symbols:
● No sparks, naked flames or
smoking.
● Always shield eyes. Explosive
gases can cause blindness or
injury.
● Keep the vehicle battery out of
reach of children.
● The vehicle battery contains
sulphuric acid which could cause
blindness or serious burn
injuries.
Vehicle care
●
●
See the Owner's Manual for
further information.
Explosive gas may be present in
the vicinity of the vehicle battery.
Power saving mode
This mode deactivates electrical
consumers to avoid excessive
discharging of the vehicle battery.
These consumers, such as the
infotainment system, windscreen
wipers, low beam headlights,
courtesy light, etc. can be used for a
total maximum time of about
40 minutes after ignition is switched
off.
Deactivating power saving mode
Power saving mode is deactivated
automatically when the engine is
restarted. Run the engine for a
sufficient charge:
● for less than 10 minutes to use
the consumers for approx.
5 minutes
● for more than 10 minutes to use
the consumers for up to approx.
30 minutes
Diesel fuel system bleeding
181
Wiper blade replacement
Within one minute after switching off
ignition, operate the wiper lever to
positon the wiper blades vertically on
the windscreen.
Lift the wiper arm until it stays in the
raised position, press button to
disengage the wiper blade and
remove.
Attach the wiper blade slightly angled
to the wiper arm and push until it
engages.
Lower wiper arm carefully.
Windscreen
Rear window
Switch off ignition.
Lift wiper arm. Disengage wiper blade
as shown in illustration and remove.
If the tank has been run dry, the diesel
fuel system must be bled. Switch on
the ignition three times for
15 seconds at a time. Then crank the
engine for a maximum of
40 seconds. Repeat this process after
no less than 5 seconds. If the engine
fails to start, seek the assistance of a
workshop.
182
Vehicle care
Attach the wiper blade slightly angled
to the wiper arm and push until it
engages.
Lower wiper arm carefully.
Bulb replacement
Halogen headlights
Switch off the ignition and switch off
the relevant switch or close the doors.
Only hold a new bulb at the base. Do
not touch the bulb glass with bare
hands.
Use only the same bulb type for
replacement.
Replace headlight bulbs from within
the engine compartment.
Bulb check
After a bulb replacement switch on
the ignition, operate and check the
lights.
1 : high beam, turn light
2 : low beam
Vehicle care
High beam
1. Rotate the cap anticlockwise and
remove it.
2. Withdraw the upper bulb holder
from the reflector housing.
3. Remove the bulb from the plug
connector by pulling.
4. Replace the bulb and connect it to
the plug connector.
5. Insert and push the bulb holder
into the reflector housing by
setting the lug into position.
6. Fit the cap and rotate clockwise.
183
Turn light
1. Rotate the cap anticlockwise and
remove it.
184
Vehicle care
2. Rotate the lower bulb holder
anticlockwise to disengage.
Withdraw the bulb holder from the
reflector housing.
Low beam
2. Lift the retainer, then pull the plug
connector backwards.
3. Fold down the retainer and
remove the bulb from the reflector
housing.
1. Rotate the cap anticlockwise and
remove it.
3. Press latch and remove the bulb
from the bulb holder.
4. Replace the bulb and attach it to
the bulb holder.
5. Insert the bulb holder into the
reflector housing and rotate
clockwise.
6. Fit the cap and rotate clockwise.
4. Replace the bulb and push it into
the reflector housing by setting
the lug into position.
5. Fold up the retainer and hold in
position.
6. Attach the plug connector to the
bulb and fix it with the retainer.
7. Fit the cap and rotate clockwise.
Vehicle care
Sidelight / daytime running light
In case of defective LEDs, have them
replaced by a workshop.
1. Turn the bulb holder anticlockwise and remove it from the
reflector housing.
LED headlights
Tail lights
Depending on version, tail lights and
brake lights are designed as LEDs. In
case of defective LEDs, have them
replaced by a workshop.
Light assembly in the body
Headlights for low and high beam,
sidelights, daytime running lights and
turn lights are designed as LEDs and
cannot be changed.
Have lights repaired by a workshop in
case of failure.
Detaching the light assembly
Front fog lights
The bulbs are accessible from the
underside of the vehicle.
2. Disengage the bulb socket from
the plug connector by pressing
the retaining lug.
3. Remove and replace the bulb
socket with bulb and attach the
plug connector.
4. Insert the bulb socket into the
reflector housing by turning
clockwise and engage.
185
1. Unscrew the two screws that
secure the light assembly.
186
Vehicle care
Remove the three screws and
take out.
b) Version with LED:
2. Remove the light assembly by
pulling it straight back.
3. Remove the bulb socket.
a) Version without LED:
Remove from the light assembly
by turning it anticlockwise.
4. Remove the bulb.
a) Version without LED:
Pull and replace.
1 : tail light / brake light
2 : turn light
b) Version with LED:
Vehicle care
Pull straight out to remove from
the socket and replace.
Attaching the light assembly
1. Depending on version, attach the
bulb carrier to the light assembly
and secure with the three screws
or attach turn light bulb socket.
Light assembly in the tailgate
2. Unscrew the plastic nut by hand.
Detaching the light assembly
1. Release the cover in the tailgate
and remove it.
2. Attach the light assembly to the
vehicle body and secure with the
two screws.
187
3. Carefully withdraw the light
assembly from the recesses and
remove.
4. Remove bulb socket.
a) Version without LED:
188
Vehicle care
Remove the reverse light bulb
socket from the light assembly by
turning it anticlockwise.
5. Remove bulb.
a) Version without LED:
Pull straight out to remove and
replace.
Press latch to release and remove
bulb socket.
b) Version with LED:
Remove and replace.
1 : tail light
2 : rear fog light or reverse light
b) Version with LED:
Attaching the light assembly
1. Depending on version, attach the
bulb carrier to the light assembly
or attach the reverse light bulb
socket.
Vehicle care
189
Side turn lights
To replace bulb, remove lamp
housing:
2. Attach the light assembly to the
tailgate.
3. Secure the light assembly with the
plastic nut.
4. Attach the cover to the tailgate.
2. Turn bulb holder anticlockwise
and remove from housing.
1. Slide the lamp housing forward
and remove it at the back.
3. Pull bulb from bulb holder and
replace it.
190
Vehicle care
4. Insert bulb holder and turn
clockwise.
5. Insert left end of the lamp, slide to
the left and insert right end.
Number plate light
The number plate light is designed as
LEDs and cannot be changed. In
case of defective LEDs, have them
replaced by a workshop.
Interior lights
Have the following bulbs replaced by
a workshop:
● courtesy light, reading lights
● load compartment light
● instrument panel illumination
Electrical system
Fuses
Data on the replacement fuse must
match the data on the defective fuse.
The three fuse boxes are located in:
● engine compartment
● instrument panel
Before replacing a fuse, turn off the
respective switch and the ignition.
A blown fuse can be recognised by its
melted wire.
Fuse extractor
A fuse extractor may be located in the
fuse box in the engine compartment.
The extractor has two sides, each
side is designed for a different type of
fuses.
Caution
Do not replace the fuse until the
cause of the fault has been
remedied.
Some functions are protected by
several fuses.
Fuses may also be inserted without
existence of a function.
Grab the fuse with the fuse extractor
and withdraw the fuse.
Vehicle care
Engine compartment fuse
box
The fuse box is in the front left of the
engine compartment.
Disengage the cover and remove it.
191
No. Circuit
10
Engine control
11
Engine control
12
Engine cooling unit
13
Body control module
14
Intelligent battery sensor
15
–
16
Front fog lights
No. Circuit
17
–
1
Fan climate control system
18
High beam right
2
–
19
High beam left
3
Body fuse box
20
Engine control fuel pump
4
–
21
Starter
5
Instrument panel fuse box
22
–
6
Engine cooling unit
23
Starter
7
Body control module
24
Trailer hitch
8
Engine control fuel pump
25
Instrument panel fuse box
9
Engine control
26
Transmission control module
192
Vehicle care
No. Circuit
Instrument panel fuse box
27
Body control module
28
Engine control module
Fuse box on the left side of the
instrument panel
29
Front wiper
30
Body control module
After having changed defective fuses,
close the fuse box cover and press
until it engages.
If the fuse box cover is not closed
correctly, malfunction may occur.
No. Circuit
In left-hand drive vehicles, the fuse
box is behind a cover in the
instrument panel. Disengage cover at
the side and remove.
1
Interior mirror, exhaust system,
electric power steering, clutch
sensor, LPG, exterior mirror
adjustment, inductive charging
2
–
3
Trailer hitch
4
Horn
5
Windscreen washer pump
front / rear
6
Windscreen washer pump
front / rear
Vehicle care
193
No. Circuit
No. Circuit
No. Circuit
7
Heated steering wheel
22 Rain sensor, front camera
8
Rear wiper
23 Door module
9
–
24 Advanced parking assist,
camera, Infotainment
35 Instrument cluster, light switch,
advanced parking assist, trans‐
mission control module
10 Central locking system
11 Central locking system
12 Instrument cluster
13 Climate control system, USB
14 OnStar
15 Instrument cluster, climate
control system
16 Brake, starter, retained power
off
17 Instrument cluster
18 Advanced parking assist
19 Top column module, trailer
control module
20 –
21 Anti-theft alarm system, start
button
25 Airbag
26 Top column module
27 Anti-theft alarm system
36 Courtesy lights, sun visor lights,
glovebox light
Fuse box on the right side of the
instrument panel
28 –
29 Infotainment
30 –
31 Infotainment
32 Power outlet front
33 –
34 Heated exterior mirrors, door
module
In left-hand drive vehicles, the fuse
box is located behind a cover in the
glovebox. Open the glovebox and
remove the cover. Remove the
bracket.
194
Vehicle care
No. Circuit
Vehicle tools
10
Power outlet rear
11
–
Tools
12
–
Vehicles with spare wheel
No. Circuit
1
Heated rear window
2
Heated exterior mirrors
3
Front power window
4
Driver's door control unit
5
Rear power window
6
Heated seats
7
–
8
Infotainment
9
–
The jack, tools, a strap for securing a
damaged wheel and the towing eye
are placed in the tool box in the right
wall of the load compartment.
Spare wheel 3 203.
Vehicle care
Vehicles without spare wheel
Wheels and tyres
Tyre condition, wheel condition
Drive over edges slowly and at right
angles if possible. Driving over sharp
edges can cause tyre and wheel
damage. Do not trap tyres on the kerb
when parking.
Regularly check the wheels for
damage. Seek the assistance of a
workshop in the event of damage or
unusual wear.
The screwdriver and the towing eye
are located in a box below the floor
cover in the load compartment.
Tyre repair kit 3 199.
Winter tyres
Winter tyres improve driving safety at
temperatures below 7 °C and should
therefore be fitted on all wheels.
In accordance with country-specific
regulations, affix the speed sticker in
the driver's field of view.
All tyre sizes are permitted as winter
tyres 3 230.
195
Tyre designations
E.g. 195/65 R 15 91 T
195 : tyre width, mm
65 : cross-section ratio (tyre height
to tyre width), %
R : belt type: Radial
RF : type: RunFlat
15 : wheel diameter, inches
91 : load index e.g. 95 is equivalent
to 615 kg
T
: speed code letter
Speed code letter:
Q : up to 160 km/h
S : up to 180 km/h
T : up to 190 km/h
H : up to 210 km/h
V : up to 240 km/h
W : up to 270 km/h
Choose a tyre appropriate for the
maximum speed of this vehicle. Refer
to the EEC Certificate of Conformity
provided with the vehicle or other
national registration documents.
Optional equipment could reduce the
maximum speed of the vehicle.
196
Vehicle care
Directional tyres
Directional tyres should be mounted
so that they rotate in the correct
direction. The proper rotation
direction is indicated by a symbol
(e.g. an arrow) on the sidewall.
Tyre pressure
Check the pressure of cold tyres at
least every 14 days and before any
long journey.
Do not forget the spare wheel.
The tyre pressure information label
on the left door frame indicates the
original equipment tyres and the
correspondent tyre pressures.
The tyre pressure data refers to cold
tyres. It applies to summer and winter
tyres.
Always inflate the spare tyre to the
pressure specified for full load.
The ECO tyre pressure serves to
achieve the smallest amount of fuel
consumption possible.
Incorrect tyre pressures will impair
safety, vehicle handling, comfort and
fuel economy and will increase tyre
wear.
The tyre pressure table indicates the
required pressure for a specific tyre
size only and shows all possible tyre
combinations 3 230.
For the tyres approved for this
vehicle, refer to the EEC Certificate of
Conformity provided with the vehicle
or other national registration
documents.
The driver is responsible for correct
adjustment of tyre pressure.
9 Warning
If the pressure is too low, this can
result in considerable tyre warmup and internal damage, leading to
tread separation and even to tyre
blow-out at high speeds.
9 Warning
For specific tyres the
recommended tyre pressure as
shown in the tyre pressure table
may exceed the maximum tyre
pressure as indicated on the tyre.
Never exceed the maximum tyre
pressure as indicated on the tyre.
Temperature dependency
The tyre pressure depends on the
temperature of the tyre. During
driving, tyre temperature and
pressure increase. Tyre pressure
values provided on the tyre
information label and tyre pressure
chart are valid for cold tyres, which
means at 20 °C.
Vehicle care
The pressure increases by nearly
10 kPa for a 10 °C temperature
increase. This must be considered
when warm tyres are checked.
Tyre deflation detection
system
The tyre deflation detection system
continually checks the rotation speed
of all four wheels and warns on low
tyre pressure condition once vehicle
is driving. This is achieved by
comparing tyre rolling circumference
with reference values and further
signals.
If a tyre loses pressure the control
indicator w illuminates and a warning
message is displayed in the Driver
Information Centre.
In this case reduce speed, avoid
sharp cornering and strong braking.
Stop at next safe opportunity and
check tyre pressure.
Control indicator w 3 85.
After adjusting tyre pressure initialise
system to extinguish the control
indicator and restart system.
Caution
197
System initialisation
Deflation detection system warns
just about low tyre pressure
condition and does not replace
regular tyre maintenance by the
driver.
In case of a system malfunction a
message is displayed in the Driver
Information Centre. Set correct tyre
pressure and reinitialise system. If the
failure continues to be displayed,
contact a workshop. The system is
inoperable when ABS or ESC has a
malfunction or a temporary spare
wheel is used.
In case of a system malfunction a
message is displayed in the Driver
Information Centre. Set correct tyre
pressure and reinitialise system. If the
failure continues to be displayed,
contact a workshop. The system is
inoperable when ABS or ESC has a
malfunction.
Once the road tyre has been refitted,
check the tyre pressure with cold
tyres and initialise the system.
After tyre pressure correction or
wheel change, the system must be
initialised to learn new circumference
reference values:
1. Always ensure that all four tyres
have correct tyre pressure
3 230.
2. Apply parking brake.
3. Press w to reset deflation
detection system.
4. Reset is confirmed by pop-up
indication.
198
Vehicle care
After initialisation system
automatically calibrates to new tyre
pressures during driving. After longer
drive the system will adopt and
monitor new pressures.
Always check tyre pressure with cold
tyres.
System has to be reinitialised when:
● tyre pressure has been changed
● load condition has been changed
● wheels have been swapped or
exchanged
The system will not warn
instantaneously on a tyre blow out or
a rapid deflation. This is due to
required calculation time.
Tread depth
Check tread depth at regular
intervals.
Tyres should be replaced for safety
reasons at a tread depth of 2-3 mm
(4 mm for winter tyres).
For safety reasons, it is
recommended that the tread depth of
the tyres on one axle should not vary
by more than 2 mm.
Changing tyre and wheel
size
The legally permissible minimum
tread depth (1.6 mm) has been
reached when the tread has worn
down as far as one of the tread wear
indicators (TWI). Their position is
indicated by markings on the
sidewall.
If there is more wear at the front than
the rear, swap round front wheels and
rear wheels periodically. If directional
tyres are mounted, ensure that the
direction of rotation of the wheels
remains the same.
Tyres age, even if they are not used.
We recommend tyre replacement
every 6 years.
If tyres of a different size than those
fitted at the factory are used, it may be
necessary to reprogramme the tyre
deflation detection system and make
other vehicle modifications.
Tyre deflation detection system
3 197.
Have the label with tyre pressures
replaced.
9 Warning
The use of unsuitable tyres or
wheels may lead to accidents and
will invalidate the vehicle
operating permit.
Wheel covers
Wheel covers and tyres that are
factory approved for the respective
vehicle and comply with all of the
relevant wheel and tyre combination
requirements must be used.
If the wheel covers and tyres used are
not factory approved, the tyres must
not have a rim protection ridge.
Vehicle care
Wheel covers must not impair brake
cooling.
9 Warning
Use of unsuitable tyres or wheel
covers could lead to sudden
pressure loss and thereby
accidents.
Vehicles with steel wheels: When
using locking wheel nuts, do not
attach wheel covers.
Tyre chains
Tyre chains are only permitted on the
front wheels.
Always use fine mesh chains that add
no more than 10 mm to the tyre tread
and the inboard sides (including chain
lock).
9 Warning
Damage may lead to tyre blowout.
Tyre chains are only permitted on
tyres of size 195/65 R15 91 and
195/60 R16 89
199
9 Warning
Do not drive faster than 80 km/h.
Do not use for a lengthy period.
Steering and handling may be
affected.
If you have a flat tyre:
Apply the parking brake and engage
first gear, reverse gear or P.
Temporary spare wheel
The use of tyre chains is not permitted
on the temporary spare wheel.
Tyre repair kit
Minor damage to the tyre tread can be
repaired with the tyre repair kit.
Do not remove foreign bodies from
the tyres.
Tyre damage exceeding 4 mm or that
is at tyre's sidewall cannot be repaired
with the tyre repair kit.
The tyre repair kit is in the load
compartment below the floor cover.
1. Remove the sealant bottle and the
compressor.
200
Vehicle care
2. Pull speed limit label from sealant
bottle and place it in driver's
visible area.
3. Remove the electrical connection
cable and air hose from the
stowage compartments on the
underside of the compressor.
4. Screw the compressor air hose to
the connection on the sealant
bottle.
5. Fit the sealant bottle into the
bracket on the compressor.
Set the compressor near the tyre
in such a way that the sealant
bottle is upright.
6. Unscrew valve cap from defective
tyre.
7. Screw the filler hose to the tyre
valve.
8. The switch on the compressor
must be set to J.
9. Connect the compressor plug to
the power outlet 3 74.
To avoid discharging the battery,
we recommend running the
engine.
Vehicle care
10. Set the rocker switch on the
compressor to I. The tyre is filled
with sealant.
11. The compressor pressure gauge
briefly indicates up to 6 bar whilst
the sealant bottle is emptying
(approx. 30 seconds). Then the
pressure starts to drop.
12. All of the sealant is pumped into
the tyre. Then the tyre is being
inflated.
13. The prescribed tyre pressure
should be obtained within
10 minutes.
Tyre pressure 3 230.
When the correct pressure is
obtained, switch off the
compressor.
If the prescribed tyre pressure is
not obtained within 10 minutes,
remove the tyre repair kit. Move
the vehicle one tyre rotation.
Reattach the tyre repair kit and
continue the filling procedure for
10 minutes. If the prescribed tyre
pressure is still not obtained, the
tyre is too badly damaged. Seek
the assistance of a workshop.
Drain excess tyre pressure with
the button on the air hose.
Do not run the compressor longer
than 10 minutes.
201
14. Detach the tyre repair kit. Remove
sealant bottle from bracket. Screw
the filler hose to the free
connection of the sealant bottle.
This prevents sealant from
escaping. Stow tyre repair kit in
load compartment.
15. Remove any excess sealant
using a cloth.
16. Continue driving immediately so
that sealant is evenly distributed
in the tyre. After driving approx.
5 km (but no more than 10 min),
stop and check tyre pressure.
Screw compressor air hose
directly onto tyre valve when
doing this. Fill tyre as described
202
Vehicle care
before. Drain excess tyre
pressure with the button on the air
hose.
If tyre pressure hasn't decreased
under 1.5 bar, set it to the correct
value. Otherwise the vehicle must
not be used. Seek assistance of a
workshop.
Repeat the checking procedure
once more after driving further
10 km (but no more than
10 minutes) to check that there is
no more loss of pressure
If the tyre pressure has fallen
below 1.5 bar, the vehicle must
not be used. Seek the assistance
of a workshop.
17. Stow away tyre repair kit in load
compartment.
Note
The driving characteristics of the
repaired tyre are severely affected,
therefore have this tyre replaced.
If unusual noise is heard or the
compressor becomes hot, turn
compressor off for at least
30 minutes.
The built-in safety valve opens at a
pressure of 700 kPa (7 bar).
Note the expiry date of the kit. After
this date its sealing capability is no
longer guaranteed. Pay attention to
storage information on sealant
bottle.
Replace the used sealant bottle.
Dispose of the bottle as prescribed
by applicable laws.
The compressor and sealant can be
used from approx. -30 °C.
Wheel changing
Make the following preparations and
observe the following information:
● Park the vehicle on a level, firm
and non-skid surface. The front
wheels must be in the straightahead position.
● If necessary, place a chock under
the wheel diagonally opposite the
wheel to be changed.
● Apply the parking brake and
engage first gear, reverse gear or
P.
●
●
●
●
●
●
If the ground on which the vehicle
is standing is soft, a solid board
(max. 1 cm thick) should be
placed under the jack.
Take heavy objects out of the
vehicle before jacking up.
No people or animals may be in
the vehicle when it is jacked-up.
Never crawl under a jacked-up
vehicle.
Do not start the vehicle when it is
raised on the jack.
Before screwing in the wheel
bolts, clean them.
9 Warning
Do not grease wheel bolts.
Tightening torques
Caution
If the vehicle is equipped with alloy
wheels, tighten the wheel bolts
manually at least for the first five
turns.
Vehicle care
There are two different types of
wheels with two different bolts and
tightening torques.
203
Jacking positions
The jacking positions shown refer to
the use of lifting arms and accessory
jacks used for changing winter /
summer tyres.
Tightening torque for alloy wheels is
100 Nm.
Front arm position of the lifting
platform centrically under the relevant
vehicle jacking point.
Spare wheel
Tightening torque for steel wheels is
115 Nm.
9 Warning
Ensure to use always the correct
wheel bolts if changing the
wheels. When installing the spare
wheel, the bolts for alloy wheels
can also be used.
Rear arm position of the lifting
platform centrically under the relevant
vehicle jacking point.
The spare wheel can be classified as
a temporary spare wheel depending
on the size compared to the other
mounted wheels and country
regulations. In this case a permissible
maximum speed applies, even
though no label at the spare wheel
indicates this.
204
Vehicle care
Caution
The use of a spare wheel that is
smaller than the other wheels or in
combination with winter tyres
could affect driveability. Have the
defective tyre replaced as soon as
possible.
There is a box with tools in the
right wall of the load
compartment.
Vehicle tools 3 194.
3. When, after a wheel change, no
wheel is placed in the spare wheel
well, fasten the wing nut and close
the floor cover.
4. After a wheel change back to a full
size wheel, place the spare wheel
outside up in the well and secure
with the wing nut.
Temporary spare wheel
Caution
If driving with a temporary spare
wheel, active emergency braking
has to deactivated.
The spare wheel is located in the load
compartment:
1. Open the floor cover.
2. The spare wheel is secured with a
wing nut. Unscrew nut and take
out the spare wheel.
Only mount one temporary spare
wheel. The permissible maximum
speed on the label on the temporary
spare wheel is only valid for the
factory-fitted tyre size.
Do not drive faster than 80 km/h. Take
curves slowly. Do not use for a long
period of time.
Fitting the spare wheel
Make the preparations given for
wheel changing 3 202 and observe
the following information:
● Never change more than one
wheel at once.
● Use the jack only to change
wheels in case of puncture, not
for seasonal winter or summer
tyre change.
● The jack is maintenance-free.
1. Disengage wheel bolt caps with a
screwdriver and remove.
Steel wheels with cover: Pull off
the wheel cover.
Alloy wheels: Disengage wheel
bolt caps with a screwdriver and
remove. To protect the wheel,
place a soft cloth between the
screwdriver and the alloy wheel.
Vehicle care
205
the jacking point in a manner that
prevents it from slipping.
2. Fold out the wheel wrench and
install ensuring that it locates
securely and loosen each wheel
bolt by half a turn.
The wheels might be protected by
locking wheel bolts. To loosen
these specific bolts, first attach
the adapter for the locking wheel
bolts onto the head of the bolt
before installing the wheel
wrench. The adapter is located in
the load compartment under the
rear floor cover.
3. Ensure the jack is correctly
positioned under the relevant
vehicle jacking point.
4. Set the jack to the necessary
height. Position it directly below
Ensure that the edge of the body
fits into the notch of the jack.
206
5.
6.
7.
8.
9.
Vehicle care
Attach wheel wrench and with the
jack correctly aligned rotate wheel
wrench until wheel is clear of the
ground.
Unscrew the wheel nuts.
Change the wheel.
Screw on the wheel nuts.
Lower the vehicle and remove
jack.
Install the wheel wrench ensuring
that it is located securely and
tighten each bolt in a crosswise
sequence. Tightening torque is
100 Nm.
bolts can also be used for the steel
spare wheel. In this case, the
spare wheel is secured by the
conical contact of each bolt. In this
case, the washers do not come
into contact with the spare wheel.
10. Align the valve hole in the wheel
cover with the tyre valve before
installing.
Install wheel nut caps.
11. Stow and secure the replaced
wheel and the tools.
12. Check the tyre pressure of the
installed tyre and the tightening
torque as soon as possible.
Stowing a damaged full size
wheel in the load compartment
The spare wheel well is not designed
for other tyre sizes than the temporary
spare wheel. A damaged full size
wheel must be stowed in the load
compartment and secured with a
strap.
Vehicle tools 3 194.
If the vehicle is equipped with
alloy wheels, note that the wheel
To secure the wheel:
1. Position the wheel outside up
close to one sidewall of the load
compartment.
2. Place the loop end of the strap
through the front lashing eye on
the appropriate side.
3. Place the hook end of the strap
through the loop and pull it until
the strap is fastened securely to
the lashing eye.
Vehicle care
Jump starting
●
Do not start with quick charger.
A vehicle with a discharged vehicle
battery can be started using jump
leads and the vehicle battery of
another vehicle.
●
9 Warning
4. Insert the strap through the
spokes of the wheel as shown in
the illustration.
5. Mount the hook to the rear lashing
eye.
6. Tighten the strap and secure it
using the buckle.
9 Danger
Always drive with folded up and
engaged rear seat backrests when
stowing a damaged full size wheel
in the load compartment.
Be extremely careful when starting
with jump leads. Any deviation
from the following instructions can
lead to injuries or damage caused
by battery explosion or damage to
the electrical systems of both
vehicles.
9 Warning
Avoid contact of the battery with
eyes, skin, fabrics and painted
surfaces. The fluid contains
sulphuric acid which can cause
injuries and damage in the event
of direct contact.
●
Never expose the vehicle battery
to naked flames or sparks.
●
●
●
●
●
●
207
A discharged vehicle battery can
already freeze at a temperature
of 0 °C. Defrost the frozen battery
before connecting jump leads.
Wear eye protection and
protective clothing when
handling a battery.
Use a booster battery with the
same voltage (12 V). Its capacity
(Ah) must not be much less than
that of the discharged vehicle
battery.
Use jump leads with insulated
terminals and a cross section of
at least 16 mm2 (25 mm2 for
diesel engines).
Do not disconnect the discharged
vehicle battery from the vehicle.
Switch off all unnecessary
electrical consumers.
Do not lean over the vehicle
battery during jump starting.
Do not allow the terminals of one
lead to touch those of the other
lead.
208
●
●
Vehicle care
The vehicles must not come into
contact with each other during
the jump starting process.
Apply the parking brake,
transmission in neutral,
automatic transmission in P.
Open the positive terminal protection
caps of both vehicle batteries.
Lead connection order:
1. Connect the red lead to the
positive terminal of the booster
battery.
2. Connect the other end of the red
lead to the positive terminal of the
discharged battery.
3. Connect the black lead to the
negative terminal of the booster
battery.
4. Connect the other end of the black
lead to a vehicle grounding point
of your vehicle in the engine
compartment.
Route the leads so that they cannot
catch on rotating parts in the engine
compartment.
To start the engine:
1. Start the engine of the vehicle
providing the jump.
2. After 5 minutes, start the other
engine. Start attempts should be
made for no longer than
15 seconds at an interval of
1 minute.
3. Allow both engines to idle for
approx. 3 minutes with the leads
connected.
4. Switch on electrical consumers
(e.g. headlights, heated rear
window) of the vehicle receiving
the jump start.
5. Reverse above sequence exactly
when removing leads.
Towing
Towing the vehicle
Wrap a cloth around the tip of a flat
screwdriver to prevent paint damage.
Insert a screwdriver in the slot at the
bottom of the cap. Release the cap by
carefully moving the screwdriver
downwards.
The towing eye is stowed with the
vehicle tools 3 194.
Vehicle care
Caution
Deactivate the driver assistance
systems like active emergency
braking 3 147, otherwise the
vehicle may automatically brake
during towing.
Switch the selector lever to neutral.
Release the parking brake.
Screw in the towing eye as far as it will
go until it stops in a horizontal
position.
Attach a tow rope – or better still a tow
rod – to the towing eye.
The towing eye must only be used for
towing and not for recovering the
vehicle.
Switch on ignition to release steering
wheel lock and to permit operation of
brake lights, horn and windscreen
wiper.
209
and when the transmission is
defective, the front axle must be
raised off the ground.
Seek the assistance of a workshop.
After towing, unscrew the towing eye.
Insert cap with the outer flange into
the recess and fix cap by pushing.
Towing another vehicle
Caution
Drive slowly. Do not drive jerkily.
Excessive tractive force can
damage the vehicle.
When the engine is not running,
considerably more force is needed to
brake and steer.
To prevent the entry of exhaust gases
from the towing vehicle, switch on the
air recirculation and close the
windows.
Vehicles with automatic transmission:
The vehicle must be towed facing
forwards, not faster than 80 km/h nor
further than 100 km. In all other cases
Wrap a cloth around the tip of a flat
screwdriver to prevent paint damage.
Insert a screwdriver in the slot at the
bottom of the cap. Release the cap by
carefully moving the screwdriver
downwards.
210
Vehicle care
The towing eye is stowed with the
vehicle tools 3 194.
Caution
Drive slowly. Do not drive jerkily.
Excessive tractive force can
damage the vehicle.
After towing, unscrew the towing eye.
Insert cap with the upper flange into
the recess and fix cap by pushing.
Screw in the towing eye as far as it will
go until it stops in a horizontal
position.
The lashing eye at the rear
underneath the vehicle must never be
used as a towing eye.
Attach a tow rope – or better still a tow
rod – to the towing eye.
The towing eye must only be used for
towing and not for recovering a
vehicle.
Appearance care
Exterior care
Locks
The locks are lubricated at the factory
using a high quality lock cylinder
grease. Use a de-icing agent only
when absolutely necessary, as this
has a degreasing effect and impairs
lock function. After using a de-icing
agent, have the locks regreased by a
workshop.
Washing
The paintwork is exposed to
environmental influences. Wash and
wax the vehicle regularly. When using
automatic vehicle washes, select a
programme that includes waxing.
Bird droppings, dead insects, resin,
pollen and the like should be cleaned
off immediately, as they contain
aggressive constituents which can
cause paint damage.
If using a vehicle wash, comply with
the vehicle wash manufacturer's
instructions. The windscreen wiper
Vehicle care
and rear window wiper must be
switched off. Remove antenna and
external accessories such as roof
racks etc.
If the vehicle is washed by hand,
make sure that the insides of the
wheel housings are also thoroughly
rinsed out.
Wax painted parts of the vehicle
regularly.
Clean edges and folds on opened
doors and the bonnet as well as the
areas they cover.
Clean bright metal mouldings with a
cleaning solution approved for
aluminium to avoid damages.
Caution
Always use a cleaning agent with
a pH value of four to nine.
Do not use cleaning agents on hot
surfaces.
Do not clean the engine compartment
with a steam-jet or high-pressure jet
cleaner.
Thoroughly rinse and leather-off the
vehicle. Rinse leather frequently. Use
separate leathers for painted and
glass surfaces: remnants of wax on
the windows will impair vision.
Have the door hinges of all doors
greased by a workshop.
Do not use hard objects to remove
spots of tar. Use tar removal spray on
painted surfaces.
Exterior lights
Headlight and other light covers are
made of plastic. Do not use any
abrasive or caustic agents, do not use
an ice scraper, and do not clean them
dry.
Polishing and waxing
Wax the vehicle regularly (at the
latest when water no longer beads).
Otherwise, the paintwork will dry out.
Polishing is necessary only if the paint
has become dull or if solid deposits
have become attached to it.
Paintwork polish with silicone forms a
protective film, making waxing
unnecessary.
211
Plastic body parts must not be treated
with wax or polishing agents.
Windows and windscreen wiper
blades
Switch off wipers before handling in
their areas.
Use a soft lint-free cloth or chamois
leather together with window cleaner
and insect remover.
When cleaning the rear window from
inside, always wipe in parallel to the
heating element to prevent damage.
For mechanical removal of ice, use a
sharp-edged ice scraper. Press the
scraper firmly against the glass so
that no dirt can get under it and
scratch the glass.
Clean smearing wiper blades with a
soft cloth and window cleaner.
Remove dirt residues from smearing
wiper blades by using a soft cloth and
window cleaner. Also make sure to
remove any residues such as wax,
insect residues and similar from the
window.
212
Vehicle care
Ice residues, pollution and continuous
wiping on dry windows will damage or
even destroy the wiper blades.
Glass panel
Never clean with solvents or abrasive
agents, fuels, aggressive media
(e.g. paint cleaner, acetonecontaining solutions etc.), acidic or
highly alkaline media or abrasive
pads.
Wheels and tyres
Do not use high-pressure jet
cleaners.
Clean rims with a pH-neutral wheel
cleaner.
Rims are painted and can be treated
with the same agents as the body.
Paintwork damage
Rectify minor paintwork damage with
a touch-up pen before rust forms.
Have more extensive damage or rust
areas repaired by a workshop.
Underbody
Interior care
Some areas of the vehicle underbody
have a PVC undercoating while other
critical areas have a durable
protective wax coating.
After the underbody is washed, check
the underbody and have it waxed if
necessary.
Bitumen / rubber materials could
damage the PVC coating. Have
underbody work carried out by a
workshop.
Before and after winter, wash the
underbody and have the protective
wax coating checked.
Interior and upholstery
Towing equipment
Do not clean the coupling ball bar with
a steam-jet or high-pressure jet
cleaner.
Only clean the vehicle interior,
including the instrument panel fascia
and panelling, with a dry cloth or
interior cleaner.
Clean the leather upholstery with
clear water and a soft cloth. In case of
heavy soiling, use leather care.
The instrument cluster and the
displays should only be cleaned using
a soft damp cloth. If necessary use a
weak soap solution.
Clean fabric upholstery with a
vacuum cleaner and brush. Remove
stains with an upholstery cleaner.
Clothing fabrics may not be
colourfast. This could cause visible
discolourations, especially on lightcoloured upholstery. Removable
stains and discolourations should be
cleaned as soon as possible.
Clean seat belts with lukewarm water
or interior cleaner.
Vehicle care
Caution
Close Velcro fasteners as open
Velcro fasteners on clothing could
damage seat upholstery.
The same applies to clothing with
sharp-edged objects, like zips or
belts or studded jeans.
Plastic and rubber parts
Plastic and rubber parts can be
cleaned with the same cleaner as
used to clean the body. Use interior
cleaner if necessary. Do not use any
other agent. Avoid solvents and petrol
in particular. Do not use highpressure jet cleaners.
Floor mats
9 Warning
If a floor mat has the wrong size or
is not properly installed, it can
interfere with the accelerator pedal
and/or brake pedal, what can
cause unintended acceleration
213
and/or increased stopping
distance which can cause a crash
and injury.
Use the following guidelines for
proper floor mat usage.
● The original equipped floor mats
were designed for your vehicle.
Have damaged floor mats only
replaced by certified floor mats.
Always check that the floor mats
do not interfere with the pedals.
● Use the floor mat with the correct
side up. Do not turn it over.
● Do not place anything on top of
the driver's side floor mat.
● Use only a single floor mat on the
driver's side.
Installing and removing the floor
mats
The driver's side floor mat and the
passenger's side floor mat are each
held in place by two retainers.
To install the floor mat:
1. Move the seat backwards as far
as possible.
2. Align slots in the mat with the
retainers, as shown.
3. Push the mat to the floor.
To remove the floor mat:
1. Move the seat backwards as far
as possible.
2. Pull the floor mat upwards to
remove.
214
Service and maintenance
Service and
maintenance
General information ................... 215
Service information .................. 215
Recommended fluids, lubricants
and parts .................................... 219
Recommended fluids and
lubricants ................................ 219
Service and maintenance
General information
Service information
In order to ensure economical and
safe vehicle operation and to
maintain the value of your vehicle, it
is of vital importance that all
maintenance work is carried out at the
proper intervals as specified.
The detailed, up-to-date service
schedule for your vehicle is available
at the workshop.
Severe operating conditions exist if
one or more of the following
circumstances occur frequently: Cold
starting, stop and go operation, e.g.
for taxis and police vehicles, trailer
operation, mountain driving, driving
on poor and sandy road surfaces,
increased air pollution, presence of
airborne sand and high dust content,
driving at high altitude and large
variations of temperature.
Under these severe operating
conditions, certain service work may
be required more frequently than the
regular service interval indicated in
the service display. Contact a
workshop for customised service
schedules.
Service display 3 80.
215
216
Service and maintenance
Confirmations
Confirmation of service is recorded in
the Service and warranty booklet.
The date and mileage is completed
with the stamp and signature of the
servicing workshop.
Make sure that the Service and
warranty booklet is completed
correctly as continuous proof of
service is essential if any warranty or
goodwill claims are to be met, and is
also a benefit when selling the
vehicle.
Service intervals
Engine code
EB2ADT
EB2ADTS
EB2FA
EP6FADTXD
Country group 1
25,000 km / 1 year
25,000 km / 1 year
30,000 km / 1 year
Country group 2
15,000 km / 1 year
25,000 km / 1 year
20,000 km / 1 year
Country group 3
15,000 km / 1 year
25,000 km / 1 year
20,000 km / 1 year
Country group 4
15,000 km / 1 year
20,000 km / 1 year
Country group 5
10,000 km / 1 year
1)
Unless otherwise indicated in the service display.
EB2DTS
10,000 km / 1 year1)
Service and maintenance
Engine code
DV5RC
DV5RD
DW10FC
Country group 1
30,000 km / 1 year 1)
30,000 km / 1 year 1)
Country group 2
30,000 km / 1 year 1)
30,000 km / 1 year 1)
Country group 3
15,000 km / 1 year
20,000 km / 1 year
Country group 4
15,000 km / 1 year
20,000 km / 1 year
15,000 km / 1 year
Country group 5
10,000 km / 1 year
10,000 km / 1 year
10,000 km / 1 year
1)
217
DV6D
Unless otherwise indicated in the service display.
Country Group 1:
Andorra, Austria, Belgium, Cyprus, Denmark, Finland, France, Germany, Greece, Iceland, Republic of Ireland, Italy,
Liechtenstein, Luxembourg, Malta, Monaco, Netherlands, Norway, Portugal, San Marino, Spain, Sweden, Switzerland,
United Kingdom.
Country Group 2:
Bosnia-Herzegovina, Bulgaria, Croatia, Czech Republic, Estonia, FYR of Macedonia, Hungary, Latvia, Lithuania, Poland,
Romania, Slovakia, Slovenia.
Country Group 3:
Albania, Montenegro, Serbia.
Country Group 4:
Israel, South Africa, Turkey, Lesotho, Swaziland.
Country Group 5:
All other countries which are not listed in the previous country groups.
218
Service and maintenance
Confirmations
Confirmation of service is recorded in the Service and warranty booklet. The date and mileage is completed with the stamp
and signature of the servicing workshop.
Make sure that the Service and warranty booklet is completed correctly as continuous proof of service is essential if any
warranty or goodwill claims are to be met, and is also a benefit when selling the vehicle.
Service and maintenance
Recommended fluids,
lubricants and parts
Recommended fluids and
lubricants
Only use products that meet the
recommended specifications.
9 Warning
Operating materials are
hazardous and could be
poisonous. Handle with care. Pay
attention to information given on
the containers.
Engine oil
Engine oil is identified by its quality
and its viscosity. Quality is more
important than viscosity when
selecting which engine oil to use. The
engine oil quality ensures e.g. engine
cleanliness, wear protection and
engine oil aging control, whereas
viscosity grade gives information on
the oil's thickness over a temperature
range.
Select the appropriate engine oil
based on its quality and on the
minimum ambient temperature
3 223.
Topping up engine oil
Caution
In case of any spilled oil, wipe it up
and dispose it properly.
Engine oils of different manufacturers
and brands can be mixed as long as
they comply with the required engine
oil quality and viscosity.
Select the appropriate engine oil
based on its quality and on the
minimum ambient temperature
3 223.
Additional engine oil additives
The use of additional engine oil
additives could cause damage and
invalidate the warranty.
Engine oil viscosity grades
The SAE viscosity grade gives
information of the thickness of the oil.
219
Multigrade oil is indicated by two
figures, e.g. SAE 5W-30. The first
figure, followed by a W, indicates the
low temperature viscosity and the
second figure the high temperature
viscosity.
Select the appropriate viscosity grade
depending on the minimum ambient
temperature 3 223.
All of the recommended viscosity
grades are suitable for high ambient
temperatures.
Coolant and antifreeze
Use only organic acid type-long life
coolant (LLC) antifreeze approved for
the vehicle. Consult a workshop.
The system is factory filled with
coolant designed for excellent
corrosion protection and frost
protection down to approx. -37 °C.
This concentration should be
maintained all year round. The use of
additional coolant additives that
intend to give additional corrosion
protection or seal against minor leaks
can cause function problems. Liability
220
Service and maintenance
for consequences resulting from the
use of additional coolant additives will
be rejected.
Washer fluid
Use only washer fluid approved for
the vehicle to prevent damage of
wiper blades, paintwork, plastic and
rubber parts. Consult a workshop.
Brake fluid
Over time, brake fluid absorbs
moisture which will reduce braking
effectiveness. The brake fluid should
therefore be replaced at the specified
interval.
AdBlue
Only use AdBlue to reduce the
nitrogen oxides in the exhaust
emission 3 130.
Technical data
Technical data
Vehicle identification .................. 221
Vehicle identification number . . 221
Identification plate ................... 221
Engine identification ................ 222
Vehicle data ............................... 223
Recommended fluids and
lubricants ................................ 223
Engine data ............................. 226
Performance ............................ 227
Vehicle dimensions ................. 229
Capacities ................................ 230
Tyre pressures ........................ 231
Vehicle identification
221
Identification plate
Vehicle identification
number
The identification plate is located on
the front left or right door frame.
The vehicle identification number is
stamped on the identification plate
and on the floor pan, under the floor
covering, visible under a cover.
The vehicle identification number
may be embossed on the instrument
panel, visible through the windscreen,
or in the engine compartment on the
right body panel.
222
Technical data
Information on identification label:
1 : manufacturer
2 : type approval number
3 : vehicle identification number
4 : permissible gross vehicle weight
rating in kg
5 : permissible gross train weight
in kg
6 : maximum permissible front axle
load in kg
7 : maximum permissible rear axle
load in kg
8 : vehicle-specific or countryspecific data
The combined total of front and rear
axle loads must not exceed the
permissible gross vehicle weight.
Vehicle's kerb weight depends on the
specification of the vehicle, e.g.
optional equipment and accessories.
Refer to the EEC Certificate of
Conformity provided with your vehicle
or other national registration
documents.
The technical data is determined in
accordance with European
Community standards. We reserve
the right to make modifications.
Specifications in the vehicle
documents always have priority over
those given in this manual.
Engine identification
The technical data tables use the
engine identifier code. The engine
data table additionally shows the
engineering code.
Engine data 3 226.
To identify the respective engine,
refer to the EEC Certificate of
Conformity provided with this vehicle
or other national registration
documents.
The Certificate of Conformity shows
the engine identifier code, other
national publications may show the
engineering code. Check piston
displacement and engine power to
identify the respective engine.
Technical data
Vehicle data
Recommended fluids and lubricants
Required engine oil quality
Country groups 3 215
Countries included in country groups 1 to 3
Opel Original engine oil
EB2FA
EB2ADT
EB2ADTS
EP6FADTXD
DV5RC
DV5RD
DV5RE
EP6FDTM
EB2DT
EC5F
DW10FC
DV6D
DV6FD
DV6FE
B71 2010 / B71 2312
B71 2312
223
224
Technical data
Vauxhall Original engine oil
EB2FA
EB2ADT
EB2ADTS
EP6FADTXD
DV5RC
DV5RD
DV5RE
EP6FDTM
EB2DT
EC5F
DW10FC
DV6D
DV6FD
DV6FE
B71 2010 / B71 2312
B71 2312
Engine EC5F: B71 2290, B71 2296 or B71 300 may also be used.
Countries included in country group 4
all engines
Opel Original engine oil
B71 2302 / B71 2297
all engines
Vauxhall Original engine oil
B71 2302 / B71 2297
Engine EC5F: B71 2296 or B71 300 may also be used.
Countries included in country group 5
all engines
Opel Original engine oil
B71 2297
Technical data
all engines
Vauxhall Original engine oil
B71 2297
Engine oil viscosity grades
Country groups 3 215
Engine oil viscosity grade
B71 2010
B71 2312
B71 2302
B71 2297
SAE 0W-20
SAE 0W-30
SAE 0W-30
SAE 5W-30
225
226
Technical data
Engine data
Engine identifier code
D12xE / F12xE
D12xHL / F12xHL
D12xHT / F12xHT
Sales designation
1.2
1.2 Turbo
1.2 Turbo
Engineering code
EB2FA
EB2DT / EB2ADT
EB2ADTS
Piston displacement [cm3]
1199
1199
1199
Engine power [kW]
61
81
96
at rpm
5750
5500
5500
Torque [Nm]
118
205
230
at rpm
2750
1750
1750
Petrol
Petrol
Petrol
recommended
95
95
95
possible
98
98
98
possible
–
–
–
Fuel type
Octane rating
1)
2)
RON1)2)
A country-specific label at the fuel filler flap can supersede the engine-specific requirement.
In certain countries, the use of a particular fuel, e.g. a specific octane rating, may be required to ensure proper engine operation.
Technical data
D15DTH
A16DT
Z16DT
D15DT
Sales designation
1.5
1.6
1.5
Engineering code
DV5RC
DV6D
DV5RD
Piston displacement [cm3]
1499
1560
1499
Engine power [kW]
88
68
75
at rpm
3750
4000
3500
Torque [Nm]
300
230
250
at rpm
1750
1750
1750
Fuel type
Diesel
Diesel
Diesel
Engine identifier code
Performance
Engine
D12xE / F12xE
D12xHL / F12xHL
D12xHT / F12xHT
Manual transmission
170
187
201
Automatic transmission
–
187
–
Maximum speed [km/h]
227
228
Technical data
Engine
D15DT
D15DTH
A16DT / Z16DT
Manual transmission
178
–
170
Automatic transmission
–
183
–
Maximum speed [km/h]
Technical data
Vehicle dimensions
Crossland X
Length [mm]
4212
Width with two exterior mirrors [mm]
1976
Width with two exterior mirrors folded [mm]
1825
Height [mm]
1597
Length of load compartment floor [mm]
793
Length of load compartment with folded rear seats [mm]
1483
Load compartment width [mm]
947
Load compartment height with cover [mm]
584
Load compartment height without cover [mm]
894
Height of load compartment opening [mm]
712
Turning circle diameter [m]
11.2
229
230
Technical data
Capacities
Engine oil
Engine
D12xE / F12xE
D12xHL / F12xHL
D12xHT / F12xHT
D15DT
A16DT / Z16DT
D15DTH
including filter [l]
3.25
3.5
3.75
3.95
between MIN and MAX [l]
1.0
1.0
1.0
1.6
Fuel tank
Petrol / diesel, refilling quantity [l]
45
AdBlue tank
AdBlue, refilling quantity [l]
14.8
Technical data
231
Tyre pressures
Comfort with up to 3 people
ECO with up to 3 people
With full load
front
rear
front
rear
front
rear
[kPa/bar]
[kPa/bar]
[kPa/bar]
[kPa/bar]
[kPa/bar]
[kPa/bar]
195/65 R15,
195/60 R16
230/2.3
230/2.3
250/2.5
250/2.5
240/2.4
290/2.9
205/60 R16,
215/50 R17
230/2.3
230/2.3
250/2.5
250/2.5
240/2.4
270/2.7
Temporary spare wheel
125/80 R16
420/4.2
420/4.2
–
–
420/4.2
420/4.2
Tyres
232
Customer information
Customer
information
Customer information
Declaration of conformity
Tansmission systems
Customer information ................ 232
Declaration of conformity ......... 232
REACH .................................... 235
Software acknowledgement .... 235
Software update ...................... 238
Registered trademarks ............ 239
Vehicle data recording and pri‐
vacy ........................................... 240
Event data recorders ............... 240
Radio Frequency Identification
(RFID) ..................................... 243
This vehicle has systems that
transmit and / or receive radio waves
subject to Directive 2014/53/EU. The
manufacturers of the systems listed
below declare conformity with
Directive 2014/53/EU. The full text of
the EU declaration of conformity for
each system is available at the
following internet address:
www.opel.com/conformity.
Importer is
Opel / Vauxhall, Bahnhofsplatz,
65423 Ruesselsheim am Main,
Germany.
Navi 5.0 IntelliLink
Continental
LCIE Bureau Veritas-Site de
Fontenay aux Roses, 33 avenue du
général Leclerc, 92260 Fontenay aux
Roses, France
Operation
Maximum output
frequency (MHz) (dBm)
2400.0 - 2483.5
2.2
2400.0 - 2483.5
15
Infotainment system R 4.0 IntelliLink
LG Electronics
European Shared Service center B.V.
Krijgsman 1, 1186 DM Amstelveen,
The Netherlands
Operation frequency:
2400.0 - 2483.5 MHz
Maximum output: 4 dBm
Infotainment system R 4.0
Clarion
244 rue du Pré à Varois, 54670
Custines, France
Operation frequency:
2400 - 2480 MHz
Maximum output: 4 dBm
OnStar module
LG Electronics
European Shared Service center B.V.
Customer information
Krijgsman 1, 1186 DM Amstelveen,
The Netherlands
Operation
Maximum output
frequency (MHz) (dBm)
2402 - 2480
4
2412 - 2462
18
880 - 915
33
1710 - 1785
24
1850 - 1910
24
1920 - 1980
24
2500 - 2570
23
Antenna module
Laird
Daimlerring 31, 31135 Hildesheim,
Germany
Operation frequency: N/A
Maximum output: N/A
Radio remote control transmitter
Hülsbeck & Fürst GmbH & Co. KG
Steeger Str. 17, 42551 Velbert,
Germany
Operation frequency: 433.92 MHz
Maximum output: 10 dBm
Radio remote control receiver
Delphi European, Middle Eastern &
African Regional Offices Customer
Technology
Center Avenue de Luxembourg,
L-4940 Bascharage, G.D. of
Luxembourg
Operation frequency:
119.0 - 128.6 kHz
Maximum output: 16dBµA/m @ 10m
Electronic key transmitter
Valeo
43 Rue Bayen, 75017 Paris, France
Operation frequency: 433.92 MHz
Maximum output: 10 dBm
Immobiliser
KOSTAL of America, Inc.
350 Stephenson Hwy, Troy MI 48083,
USA
Operation frequency: 125 kHz
Maximum output: 5 dBμA/m at 10m
233
234
Jack
Customer information
Customer information
Translation of the original declaration
of conformity
Declaration of conformity according
to EC Directive 2006/42/EC
We declare that the product:
Product designation: Jack
Type/GM part number: 3637376
Type/PSA part number: 9649243380
is in compliance with the provisions of
Directive 2006/42/EC.
Applied technical standards:
GMN9737
: jacking
GM 14337
: standard equipment
jack – hardware
tests
GMW15005 : standard equipment
jack and spare tyre,
vehicle test
ISO TS 16949 : quality
management
systems
The signatory is authorised to
compile the technical documentation.
Rüsselsheim, 13th December 2016
signed by
André-Alexander Konter
Engineering Group Manager Tyre
and Wheel Systems
Adam Opel AG
D-65423 Rüsselsheim
ICASA type approval numbers
List of all Independent
Communications Authority of South
Africa (ICASA) type approval
numbers:
TA-2016/121, TA-2016/3261,
TA-2017/2387, TA-2017/2745,
TA-2013/430, TA-2017/1106,
TA-2016/929, TA-2017/3180
235
REACH
Registration, Evaluation,
Authorisation and Restriction of
Chemicals (REACH) is a European
Union regulation adopted to improve
the protection of human health and
the environment from the risks that
can be posed by chemicals. Visit
www.opel.com/reach for further
information and for access to the
Article 33 communication.
Software acknowledgement
Certain OnStar components include
libcurl and unzip software and other
third party software. Below are the
notices and licenses associated with
libcurl and unzip and for other third
party software please see http://
www.lg.com/global/support/
opensource/index.
Please find the translated text below
the original text.
libcurl
Copyright and permission notice
Copyright (c) 1996 - 2010, Daniel
Stenberg, <[email protected]>.
236
Customer information
All rights reserved.
Permission to use, copy, modify, and
distribute this software for any
purpose with or without fee is hereby
granted, provided that the above
copyright notice and this permission
notice appear in all copies.
The software is provided "as is",
without warranty of any kind, express
or implied, including but not limited to
the warranties of merchantability,
fitness for a particular purpose and
noninfringement of third party rights.
In no event shall the authors or
copyright holders be liable for any
claim, damages or other liability,
whether in an action of contract, tort
or otherwise, arising from, out of or in
connection with the software or the
use or other dealings in the software.
Except as contained in this notice, the
name of a copyright holder shall not
be used in advertising or otherwise to
promote the sale, use or other
dealings in this Software without prior
written authorization of the copyright
holder.
unzip
This is version 2005-Feb-10 of the
Info-ZIP copyright and license. The
definitive version of this document
should be available at ftp://ftp.infozip.org/pub/infozip/license.html
indefinitely.
Copyright (c) 1990-2005 Info-ZIP. All
rights reserved.
For the purposes of this copyright and
license, “Info-ZIP” is defined as the
following set of individuals:
Mark Adler, John Bush, Karl Davis,
Harald Denker, Jean-Michel Dubois,
Jean-loup Gailly, Hunter Goatley, Ed
Gordon, Ian Gorman, Chris Herborth,
Dirk Haase, Greg Hartwig, Robert
Heath, Jonathan Hudson, Paul
Kienitz, David Kirschbaum, Johnny
Lee, Onno van der Linden, Igor
Mandrichenko, Steve P. Miller, Sergio
Monesi, Keith Owens, George
Petrov, Greg Roelofs, Kai Uwe
Rommel, Steve Salisbury, Dave
Smith, Steven M. Schweda, Christian
Spieler, Cosmin Truta, Antoine
Verheijen, Paul von Behren, Rich
Wales, Mike White.
This software is provided “as is,”
without warranty of any kind, express
or implied. In no event shall Info-ZIP
or its contributors be held liable for
any direct, indirect, incidental, special
or consequential damages arising out
of the use of or inability to use this
software.
Permission is granted to anyone to
use this software for any purpose,
including commercial applications,
and to alter it and redistribute it freely,
subject to the following restrictions:
1. Redistributions of source code
must retain the above copyright
notice, definition, disclaimer, and
this list of conditions.
2. Redistributions in binary form
(compiled executables) must
reproduce the above copyright
notice, definition, disclaimer, and
this list of conditions in
documentation and/or other
materials provided with the
distribution. The sole exception to
this condition is redistribution of a
standard UnZipSFX binary
(including SFXWiz) as part of a
self-extracting archive; that is
Customer information
permitted without inclusion of this
license, as long as the normal
SFX banner has not been
removed from the binary or
disabled.
3. Altered versions--including, but
not limited to, ports to new
operating systems, existing ports
with new graphical interfaces, and
dynamic, shared, or static library
versions--must be plainly marked
as such and must not be
misrepresented as being the
original source. Such altered
versions also must not be
misrepresented as being Info-ZIP
releases--including, but not
limited to, labeling of the altered
versions with the names “InfoZIP” (or any variation thereof,
including, but not limited to,
different capitalizations), “Pocket
UnZip,” “WiZ” or “MacZip” without
the explicit permission of Info-ZIP.
Such altered versions are further
prohibited from misrepresentative
use of the Zip-Bugs or Info-ZIP email addresses or of the Info-ZIP
URL(s).
4. Info-ZIP retains the right to use
the names “Info-ZIP,” “Zip,”
“UnZip,” “UnZipSFX,” “WiZ,”
“Pocket UnZip,” “Pocket Zip,” and
“MacZip” for its own source and
binary releases.
libcurl
Copyright and permission notice
Copyright (c) 1996 - 2010, Daniel
Stenberg, <[email protected]>.
All rights reserved.
Permission to use, copy, modify, and
distribute this software for any
purpose with or without fee is hereby
granted, provided that the above
copyright notice and this permission
notice appear in all copies.
The software is provided "as is",
without warranty of any kind, express
or implied, including but not limited to
the warranties of merchantability,
fitness for a particular purpose and
noninfringement of third party rights.
In no event shall the authors or
237
copyright holders be liable for any
claim, damages or other liability,
whether in an action of contract, tort
or otherwise, arising from, out of or in
connection with the software or the
use or other dealings in the software.
Except as contained in this notice, the
name of a copyright holder shall not
be used in advertising or otherwise to
promote the sale, use or other
dealings in this Software without prior
written authorization of the copyright
holder.
unzip
This is version 2005-Feb-10 of the
Info-ZIP copyright and license. The
definitive version of this document
should be available at ftp://ftp.infozip.org/pub/infozip/license.html
indefinitely.
Copyright (c) 1990-2005 Info-ZIP. All
rights reserved.
For the purposes of this copyright and
license, “Info-ZIP” is defined as the
following set of individuals:
Mark Adler, John Bush, Karl Davis,
Harald Denker, Jean-Michel Dubois,
Jean-loup Gailly, Hunter Goatley, Ed
238
Customer information
Gordon, Ian Gorman, Chris Herborth,
Dirk Haase, Greg Hartwig, Robert
Heath, Jonathan Hudson, Paul
Kienitz, David Kirschbaum, Johnny
Lee, Onno van der Linden, Igor
Mandrichenko, Steve P. Miller, Sergio
Monesi, Keith Owens, George
Petrov, Greg Roelofs, Kai Uwe
Rommel, Steve Salisbury, Dave
Smith, Steven M. Schweda, Christian
Spieler, Cosmin Truta, Antoine
Verheijen, Paul von Behren, Rich
Wales, Mike White.
This software is provided “as is,”
without warranty of any kind, express
or implied. In no event shall Info-ZIP
or its contributors be held liable for
any direct, indirect, incidental, special
or consequential damages arising out
of the use of or inability to use this
software.
Permission is granted to anyone to
use this software for any purpose,
including commercial applications,
and to alter it and redistribute it freely,
subject to the following restrictions:
1. Redistributions of source code
must retain the above copyright
notice, definition, disclaimer, and
this list of conditions.
2. Redistributions in binary form
(compiled executables) must
reproduce the above copyright
notice, definition, disclaimer, and
this list of conditions in
documentation and/or other
materials provided with the
distribution. The sole exception to
this condition is redistribution of a
standard UnZipSFX binary
(including SFXWiz) as part of a
self-extracting archive; that is
permitted without inclusion of this
license, as long as the normal
SFX banner has not been
removed from the binary or
disabled.
3. Altered versions--including, but
not limited to, ports to new
operating systems, existing ports
with new graphical interfaces, and
dynamic, shared, or static library
versions--must be plainly marked
as such and must not be
misrepresented as being the
original source. Such altered
versions also must not be
misrepresented as being Info-ZIP
releases--including, but not
limited to, labeling of the altered
versions with the names “InfoZIP” (or any variation thereof,
including, but not limited to,
different capitalizations), “Pocket
UnZip,” “WiZ” or “MacZip” without
the explicit permission of Info-ZIP.
Such altered versions are further
prohibited from misrepresentative
use of the Zip-Bugs or Info-ZIP email addresses or of the Info-ZIP
URL(s).
4. Info-ZIP retains the right to use
the names “Info-ZIP,” “Zip,”
“UnZip,” “UnZipSFX,” “WiZ,”
“Pocket UnZip,” “Pocket Zip,” and
“MacZip” for its own source and
binary releases.
Software update
The Infotainment system can
download and install selected
software updates over a wireless
connection.
Customer information
Note
The availability of these over-the-air
vehicle software updates varies by
vehicle and country. Find more
information on our home page.
Internet connection
Downloading over-the-air vehicle
software updates requires internet
connectivity, which can be accessed
through a password-protected Wi-Fi
hotspot, e.g. provided by a mobile
phone.
Wi-Fi hotspot is also provided by the
built-in OnStar module.
To connect the Infotainment system
to a hotspot, select Settings on the
home screen, Wi-Fi and then Manage
Wi-Fi Networks. Select the desired
Wi-Fi network, and follow the onscreen prompts.
Updates
The system will prompt for certain
updates to be downloaded and
installed. There is also an option to
check for updates manually.
To manually check for updates, select
Settings on the home screen,
Software Information and then
System Update. Follow the on-screen
prompts.
Note
Steps for downloading and installing
updates may vary by vehicle.
Note
During the installation process, the
vehicle may not be operational.
Registered trademarks
Apple Inc.
Apple CarPlay™ is a trademark of
Apple Inc.
App Store® and iTunes Store® are
registered trademarks of Apple Inc.
iPhone®, iPod®, iPod touch®, iPod
nano®, iPad® and Siri® are registered
trademarks of Apple Inc.
Bluetooth SIG, Inc.
Bluetooth® is a registered trademark
of Bluetooth SIG, Inc.
DivX, LLC
DivX® and DivX Certified® are
registered trademarks of DivX, LLC.
239
EnGIS Technologies, Inc.
BringGo® is a registered trademark of
EnGIS Technologies, Inc.
Google Inc.
Android™ and Google Play™ Store
are trademarks of Google Inc.
Stitcher Inc.
Stitcher™ is a trademark of Stitcher,
Inc.
Velcro Companies
Velcro® is a registered trademark of
Velcro Companies.
Verband der Automobilindustrie e.V.
AdBlue® is a registered trademark of
the VDA.
240
Customer information
Vehicle data recording
and privacy
Event data recorders
Electronic control units are installed in
your vehicle. Control units process
data which is received by vehicle
sensors, for example, or which they
generate themselves or exchange
amongst themselves. Some control
units are necessary for the safe
functioning of your vehicle, others
assist you while you drive (driver
assistance systems), while others
provide comfort or infotainment
functions.
The following contains general
information about data processing in
the vehicle. You will find additional
information as to which specific data
is uploaded, stored and passed on to
third parties and for what purpose in
your vehicle under the key word Data
Protection closely linked to the
references for the affected functional
characteristics in the relevant owner's
manual or in the general terms of
sale. These are also available online.
Personal reference
Each vehicle is identified by means of
a unique chassis number. In
Germany, this vehicle identification
number can be traced to the present
and former keepers of the vehicle by
means of information held by the
Federal Motor Transport Authority.
Further options, such as the vehicle's
number plate, make it possible to
trace data on the keeper or driver of
the vehicle.
The data generated or processed by
control units may therefore be
personal, or be made personal under
certain conditions. Depending on
what vehicle data is available,
conclusions may be drawn on
information such as your driving
behaviour, your location or the route
you travel, or on your usage
behaviour.
Your rights in respect of data
protection
According to applicable law on data
protection, you have certain rights in
respect of companies that process
your personal data.
Accordingly you have free and
extensive entitlement to information
held by the manufacturer as well as
third parties (e.g. authorised
breakdown services or garages,
providers of online services for your
vehicle) if they have saved personal
data relating to you. In doing so you
may demand to know what data is
stored about you for what purpose,
and where the data came from. Your
right to information also covers the
transfer of data to other locations.
Further information on your legal
rights in respect of the manufacturer
(e.g. your right to deletion or the
correction of data) can be found in the
relevant privacy notice on the
manufacturer's website (including
contact data for the manufacturer and
its data protection officer).
Data that is only stored locally in the
vehicle can be read with expert
assistance at a garage, for example;
for a fee where applicable.
Customer information
Legal requirements for
information disclosure
Insofar as regulatory requirements
exist, manufacturers are strictly
bound to release data stored by the
manufacturer in individual cases to
the extent requested following a
request by state bodies (e.g. during
criminal investigations).
Government agencies are also
authorised, in the context of
applicable law, to read data in
individual cases from vehicles
themselves. Thus information that
may help with the investigation
resolution can possibly be read from
the airbag control unit in the event of
an accident.
Operating data in the vehicle
Control units process data for
operation of the vehicle.
This data includes, for example:
● vehicle status information (e.g.
speed, movement delay, lateral
acceleration, wheel rotation rate,
"seat belts fastened" display)
● ambient conditions (e.g.
temperature, rain sensor,
distance sensor)
As a rule such data is transient and is
not stored for longer than an
operational cycle, and only processed
on board the vehicle itself. Often
control units include data storage
(including the vehicle key). This is
used to allow information to be
documented temporarily or
permanently on vehicle condition,
component stress, maintenance
requirements and technical events
and errors.
Depending on technical equipment
levels, the data stored is as follows:
● system component operating
states (e.g. fill level, tyre
pressure, battery status)
● faults and defects in important
system components (e.g. lights,
brakes)
●
241
system reactions in special
driving situations (e.g. triggering
of an airbag, actuation of the
stability control systems)
● information on events damaging
the vehicle
● for electric vehicles the amount of
charge in the high-voltage
battery, estimated range
In special cases (e.g. if the vehicle
has detected a malfunction), it may be
necessary to save data that would
otherwise just be volatile.
When you use services (e.g. repairs,
maintenance), the operating data
saved can be read together with the
vehicle identification number and
used where necessary. Staff working
for the service network (e.g. garages,
manufacturers) or third parties (e.g.
breakdown services) can read the
data from the vehicle. The same
applies to warranty work and quality
assurance measures.
Data is generally read via the OBD
(On-Board Diagnostics) port
prescribed by law in the vehicle. The
operating data read documents the
technical condition of the vehicle or
242
Customer information
individual components and assists
with fault diagnosis, compliance with
warranty obligations and quality
improvement. This data, in particular
information on component stress,
technical events, operator errors and
other faults, is transmitted to the
manufacturer where appropriate,
together with the vehicle identification
number. The manufacturer is also
subject to product liability. The
manufacturer potentially also uses
operating data from vehicles for
product recalls. This data can also be
used to check customer warranty and
guarantee claims.
Fault memories in the vehicle can be
reset by a service company when
carrying out servicing or repairs or at
your request.
Comfort and infotainment
functions
Comfort settings and custom settings
can be stored in the vehicle and
changed or reset at any time.
Depending on the equipment level in
question, these include
● seat and steering wheel position
settings
● chassis and air conditioning
settings
● custom settings such as interior
lighting
You can input your own data in the
infotainment functions for your
vehicle as part of the selected
features.
Depending on the equipment level in
question, these include
● multimedia data such as music,
videos or photos for playback in
an integrated multimedia system
● address book data for use with an
integrated hands-free system or
an integrated navigation system
● input destinations
● data on the use of online services
This data for comfort and
infotainment functions can be stored
locally in the vehicle or be kept on a
device that you have connected to the
vehicle (e.g. a smartphone, USB stick
or MP3 player). Data that you have
input yourself can be deleted at any
time.
This data can only be transmitted out
of the vehicle at your request,
particularly when using online
services in accordance with the
settings selected by you.
Smartphone integration, e.g.
Android Auto or Apple CarPlay
If your vehicle is equipped
accordingly, you can connect your
smartphone or another mobile device
to the vehicle so that you can control
it via the controls integrated in the
vehicle. The smartphone image and
sound can be output via the
multimedia system in this case. At the
same time, specific information is
transmitted to your smartphone.
Depending on the type of integration,
this includes data such as position
data, day / night mode and other
general vehicle information. For more
information, please see the operating
instructions for the vehicle /
infotainment system.
Customer information
Integration allows selected
smartphone apps to be used, such as
navigation or music playback. No
further integration is possible
between smartphone and vehicle, in
particular active access to vehicle
data. The nature of further data
processing is determined by the
provider of the app used. Whether
you can define settings, and if so
which ones, is dependent on the app
in question and your smartphone's
operating system.
Online services
If your vehicle has a radio network
connection, this allows data to be
exchanged between your vehicle and
other systems. The radio network
connection is made possible by
means of a transmitter device in your
vehicle or a mobile device provided
by you (e.g. a smartphone). Online
functions can be used via this radio
network connection. These include
online services and applications /
apps provided to you by the
manufacturer or other providers.
Proprietary services
In the case of the manufacturer's
online services, the relevant functions
are described by the manufacturer in
an appropriate location (e.g. Owner's
Manual, the manufacturer's website)
and the associated data protection
information is provided. Personal
data may be used to provide online
services. Data exchange for this
purpose takes place via a protected
connection, e.g. using the
manufacturer's IT systems provided
for the purpose. Collection,
processing and use of personal data
for the purposes of preparation of
services take place solely on the
basis of legal permission, e.g. in the
case of a legally prescribed
emergency communication system or
a contractual agreement, or by virtue
of consent.
You can activate or deactivate the
services and functions (which are
subject to charges to some extent)
and, in some cases, the vehicle's
entire radio network connection. This
243
does not include statutory functions
and services such as an emergency
communication system.
Third party services
If you make use of online services
from other providers (third parties),
these services are subject to the
liability and data protection and usage
conditions of the provider in question.
The manufacturer frequently has no
influence over the content exchanged
in this regard.
Therefore, please note the nature,
scope and purpose of the collection
and use of personal data within the
scope of third party services provided
by the service provider in question.
Radio Frequency
Identification (RFID)
RFID technology is used in some
vehicles for functions such as
immobiliser. It is also used in
connection with conveniences such
as radio remote controls for door
locking / unlocking and starting. RFID
technology in Opel vehicles does not
244
Customer information
use or record personal information or
link with any other Opel system
containing personal information.
RFID technology is used in some
vehicles for functions such as
immobiliser. It is also used in
connection with conveniences such
as radio remote controls for door
locking / unlocking and starting. RFID
technology in Vauxhall vehicles does
not use or record personal
information or link with any other
Vauxhall system containing personal
information.
Customer information
245
246
Index
A
Accessories and vehicle
modifications .......................... 174
Active emergency braking.... 87, 147
AdBlue.......................... 85, 130, 230
Adjustable air vents ................... 118
Advanced parking assist............ 153
Airbag and belt tensioners ........... 82
Airbag deactivation ................ 54, 82
Airbag label................................... 49
Airbag system .............................. 49
Air conditioning regular
operation ................................ 119
Air conditioning system .............. 110
Air intake .................................... 119
Air vents...................................... 118
Antilock brake system ................ 137
Antilock brake system (ABS) ....... 84
Anti-theft alarm system ................ 31
Anti-theft locking system .............. 30
Appearance care........................ 210
Armrest............................. 44, 45, 62
Ashtrays ....................................... 76
Automatic anti-dazzle .................. 35
Automatic crash notification (ACN) 98
Automatic light control ............... 101
Automatic locking ........................ 28
Automatic transmission ............. 133
Autostop............................... 86, 126
Auxiliary heater........................... 117
B
Battery discharge protection ...... 108
Belts.............................................. 46
BlueInjection............................... 130
Bonnet ....................................... 176
Brake and clutch system ............. 83
Brake assist ............................... 139
Brake fluid .......................... 179, 219
Brake light................................... 185
Brakes ............................... 137, 179
Breakdown.................................. 208
Bulb replacement ....................... 182
C
Capacities .................................. 230
Catalytic converter ..................... 130
Central locking system ................ 23
Centre console lighting .............. 107
Centre console storage ............... 62
Changing tyre and wheel size . . . 198
Charging system .......................... 82
Child locks ................................... 28
Child restraint installation
locations ................................... 58
Child restraints.............................. 55
Child restraint systems ................ 55
Cigarette lighter ........................... 76
Climate control ............................. 15
Climate control systems............. 109
Clock............................................. 74
247
Control indicators.......................... 81
Control of the vehicle ................. 122
Controls........................................ 70
Convex shape .............................. 33
Coolant and antifreeze............... 219
Cornering lights.......................... 103
Cruise control ...................... 87, 140
Cupholders .................................. 61
Curtain airbag system .................. 53
D
Danger, Warnings and Cautions . . . 4
Daytime running lights ............... 103
Declaration of conformity............ 232
DEF............................................ 130
Deflation detection system........... 85
Diesel exhaust fluid.................... 130
Diesel fuel system bleeding ....... 181
Door open .................................... 87
Doors............................................ 29
Driver alert.................................. 164
Driver assistance systems.......... 140
Driver Information Centre............. 88
Driving characteristics and
towing tips .............................. 169
Driving hints................................ 122
E
Electric adjustment ...................... 33
Electrical system......................... 190
Electronic climate control system 113
Electronic driving programmes . . 135
Electronic key system................... 22
Electronic Stability Control and
Traction Control system.... 84, 139
Electronic Stability Control and
Traction Control system off....... 85
Emergency call............................. 98
End-of-life vehicle recovery ....... 175
Engine compartment fuse box ... 191
Engine coolant ........................... 178
Engine coolant temperature ........ 85
Engine coolant temperature
gauge ....................................... 79
Engine data ............................... 226
Engine exhaust .......................... 129
Engine identification................... 222
Engine oil ........... 177, 219, 223, 230
Engine oil level monitor................ 79
Engine oil pressure ...................... 85
Entry lighting .............................. 107
Event data recorders.................. 240
Exhaust filter......................... 85, 129
Exit lighting ................................ 107
Exterior care .............................. 210
Exterior light ................................. 86
Exterior lighting .................... 12, 100
Exterior mirrors............................. 33
F
Fault ........................................... 135
First aid......................................... 66
First aid kit ................................... 66
Fixed air vents ........................... 119
Floor mats................................... 213
Folding mirrors ............................. 34
Forward collision alert................. 145
Front airbag system ..................... 52
Front fog lights ............. 86, 104, 185
Front pedestrian protection........ 149
Front seats.................................... 41
Fuel............................................. 166
Fuel for diesel engines .............. 166
Fuel for petrol engines ............... 166
Fuel gauge ................................... 79
Fuel tank..................................... 230
Fuses ......................................... 190
G
Gauges......................................... 77
Gear selection ........................... 134
Gear shifting................................. 84
General information ................... 169
Glass panel .................................. 39
Glovebox ..................................... 61
H
Halogen headlights .................... 182
Hand brake......................... 137, 138
Hazard warning flashers ............ 103
248
Headlight flash ........................... 102
Headlight range adjustment ...... 102
Headlights................................... 100
Headlights when driving abroad 103
Head restraint adjustment ............. 8
Head restraints ............................ 40
Head-up display............................ 92
Heated mirrors ............................. 34
Heated rear window ..................... 38
Heated steering wheel ................. 70
Heated windscreen....................... 38
Heating ........................................ 44
Heating and ventilation system . 109
High beam ........................... 86, 101
High beam assist.................. 86, 101
Hill start assist ........................... 139
Horn ....................................... 13, 71
I
Identification plate ..................... 221
Ignition switch positions ............. 123
Immobiliser .................................. 33
Indicators...................................... 77
Inductive charging........................ 75
Info Display................................... 90
Instrument cluster ........................ 76
Instrument panel fuse box ......... 192
Instrument panel illumination
control .................................... 106
Instrument panel overview ........... 10
Interior care ............................... 212
Interior lighting............................ 106
Interior lights ...................... 106, 190
Interior mirrors.............................. 35
Interruption of power supply ...... 135
Introduction .................................... 3
J
Jump starting ............................. 207
K
Keys ............................................. 20
Keys, locks................................... 20
L
Lane departure warning....... 84, 163
Lashing eyes ............................... 65
LED headlights................... 103, 185
Lighting features......................... 107
Light switch ................................ 100
Load compartment ................ 29, 62
Load compartment cover ............. 64
Loading information ..................... 67
Low beam..................................... 86
Low fuel ....................................... 86
M
Malfunction indicator light ............ 82
Manual anti-dazzle ...................... 35
Manual mode ............................. 135
Manual transmission .................. 136
Manual windows .......................... 36
Mirror adjustment ........................... 9
Misted light covers ..................... 105
N
New vehicle running-in .............. 122
Number plate light ..................... 190
O
Object detection systems........... 150
Odometer ..................................... 78
Oil, engine.......................... 219, 223
Opel Connect................................ 98
Outside temperature .................... 73
Overrun cut-off ........................... 126
P
Panoramic view system.............. 159
Parking ................................ 18, 128
Parking assist ............................ 150
Parking brake....................... 83, 138
Parking lights ............................. 105
Particulate filter........................... 129
Performance .............................. 227
Performing work ........................ 176
Power button.............................. 123
Power outlets ............................... 74
Power windows ............................ 36
Preheating ................................... 85
Puncture..................................... 203
249
Q
Quickheat................................... 117
R
Radio Frequency Identification
(RFID)..................................... 243
Radio remote control ................... 21
Rain sensor.................................. 87
REACH....................................... 235
Reading lights ............................ 106
Rear floor storage cover .............. 64
Rear fog light ............... 87, 105, 185
Rear seats ................................... 45
Rear view camera ...................... 162
Rear window wiper and washer . . 73
Recommended fluids and
lubricants ........................ 219, 223
Refuelling ................................... 167
Registered trademarks............... 239
Reverse light............................... 185
Reversing lights ......................... 105
Ride control systems.................. 139
Roadside assistance.................... 98
Roof.............................................. 39
Roof load...................................... 67
Roof rack ..................................... 67
S
Safety belts................................... 46
Seat adjustment ....................... 7, 42
Seat belt ........................................ 8
Seat belt reminder ....................... 81
Seat belts ..................................... 46
Seat heating................................. 44
Seat position ................................ 41
Selective catalytic reduction....... 130
Selector lever.............................. 134
Service ............................... 119, 215
Service display ............................ 80
Service information .................... 215
Service vehicle soon .................... 83
Side airbag system ...................... 52
Side blind spot alert.............. 87, 158
Sidelights.................................... 100
Side turn lights ........................... 189
Software acknowledgement....... 235
Software update......................... 238
SOS.............................................. 98
Spare wheel ............................... 203
Speed limiter......................... 87, 143
Speedometer ............................... 77
Starting and operating................ 122
Starting off ................................... 16
Starting the engine .................... 124
Steering...................................... 122
Steering wheel adjustment ...... 9, 70
Steering wheel controls ............... 70
Stop engine.................................. 83
Stop-start system........................ 126
Storage......................................... 61
Storage compartments................. 61
Sun visor lights .......................... 107
Sun visors .................................... 38
Symbols ......................................... 4
System check............................... 83
T
Tachometer ................................. 78
Tail lights ................................... 185
Three-point seat belt .................... 47
Through-loading facility................ 62
Tools .......................................... 194
Tow bar....................................... 169
Towing................................ 169, 208
Towing another vehicle ............. 209
Towing equipment ..................... 170
Towing the vehicle ..................... 208
Trailer hitch................................. 169
Trailer towing ............................. 170
Transmission ............................... 16
Transmission display ................. 133
Tread depth ............................... 198
Trip odometer .............................. 78
Turn lights ............................ 81, 104
Tyre chains ................................ 199
Tyre deflation detection system . 197
Tyre designations ...................... 195
Tyre pressure ............................ 196
Tyre pressures ........................... 231
Tyre repair kit ............................. 199
250
U
Ultrasonic parking assist............. 150
Upholstery.................................. 212
USB port....................................... 74
Using this manual .......................... 3
V
Vauxhall Connect......................... 98
Vehicle battery ........................... 179
Vehicle checks............................ 176
Vehicle data................................ 223
Vehicle data recording and
privacy..................................... 240
Vehicle dimensions .................... 229
Vehicle identification number .... 221
Vehicle jack................................ 194
Vehicle messages ....................... 94
Vehicle personalisation ............... 95
Vehicle security............................ 30
Vehicle specific data ...................... 3
Vehicle storage........................... 175
Vehicle tools............................... 194
Vehicle unlocking ........................... 6
Ventilation................................... 109
W
Warning chimes ........................... 94
Warning lights............................... 77
Warning triangle .......................... 66
Washer and wiper systems ......... 13
Washer fluid ............................... 178
Wheel
Tightening torque.................... 203
Wheel changing ......................... 202
Wheel covers ............................. 198
Wheels and tyres ....................... 195
Windows....................................... 35
Windscreen................................... 35
Windscreen wiper and washer .... 71
Winter tyres ............................... 195
Wiper blade replacement .......... 181
www.opel.com
Copyright by Opel Automobile GmbH, Rüsselsheim, Germany.
The information contained in this publication is effective as of the date indicated below. Opel Automobile GmbH reserves the right to make changes to the technical specifications, features
and design of the vehicles relative to the information in this publication as well as changes to the publication itself.
Edition: May 2019, Opel Automobile GmbH, Rüsselsheim.
Printed on chlorine-free bleached paper.
ID-OCDAOBSE1905-en
*ID-OCDAOBSE1905-EN*
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement