Focal Point Cardivik LED Electric Stove User Manual

Add to My manuals
7 Pages

advertisement

Focal Point Cardivik LED Electric Stove User Manual | Manualzz
INSTALLATION & USER INSTRUCTIONS
LED ELECTRIC STOVE
MODELS COVERED BY THESE INSTRUCTIONS
Focal Point Fires
Christchurch, Dorset BH23 2BT
Tel: 01202 499330
Fax: 01202 499326
www.focalpointfires.co.uk
e : [email protected]
CARDIVIK LED ELECTRIC STOVE BLACK - EAN 5023539020009
CARDIVIK LED ELECTRIC STOVE CREAM - EAN 5023539020016
CARDIVIK LED ELECTRIC STOVE GREY - EAN 5023539020023
GB IE
MODEL SHOWN: CARDIVIK LED ELECTRIC STOVE
Questions or problems with your appliance?
Don’t take it back to the store
just give us a call on 01202 588601 we’re here to help
lines open between 9am and 5pm, Monday to Friday
Please note : Except where otherwise stated, all rights,
including copyright in the text, images and layout of this
booklet is owned by Focal Point Fires plc. You are not permitted to copy or adapt any of the content without the
prior written permission of Focal Point Fires plc.
All instructions must be handed to the user for
safekeeping.
Revision A - 08/17
1
© 2017 Focal Point Fires plc.
Section
1.0
2.0
3.0
4.0
5.0
6.0
7.0
I N S TA L L AT I O N & U S E R I N S T R U C T I O N S
Contents
Important Notes
Installation Requirements
Appliance Data
Unpacking the Appliance
Component Checklist
Operating the Appliance
Safety Cut-Out System
Page No. Section
2
8.0
3
9.0
3 10.0
3 11.0
3 12.0
4 13.0
5
1.0 IMPORTANT NOTES
GB IE
Contents
Page No.
Cleaning and Maintenance
5
Spares
5
Servicing
5
Troubleshoot Guide
6
Appliance Dimensions
6
Guarantee - Terms and Conditions
7
IMPORTANT - THESE INSTRUCTIONS SHOULD BE READ CAREFULLY
AND RETAINED FOR FUTURE REFERENCE.
When using this electrical appliance, basic precautions should be followed to reduce the risk
of fire, electric shock and injury to person, including the following:
• This heater must be used on an AC supply only and the voltage marked on the heater’s
rating label must correspond to the supply voltage.
• DO NOT switch the appliance on until it is properly installed as described in this
manual.
• This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
• Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children aged from 3 years and less than 8 years shall not
plug in, regulate and clean the appliance or perform user maintenance.
• CAUTION: Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are present.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
• The heater must not be located immediately below a socket-outlet.
• DO NOT use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
• WARNING: In order to avoid overheating, do not cover the heater.
• DO NOT use this heater with a programmer, timer, separate remote-control system or
any other device that switches the heater on automatically, since a fire risk exists if the
heater is covered or positioned incorrectly.
• CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal
cutout, this appliance must not be supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched on and off by the utility.
• Keep furniture, curtains and other fabric material away from the appliance.
• DO NOT leave the appliance unattended during use.
• From time to time, check the cord for damage. Never use the appliance if the cord or any
part of the appliance shows signs of damage.
2
© 2017 Focal Point Fires plc.
1.0 IMPORTANT NOTES - CONTINUED
GB IE
• DO NOT run the mains cable under carpets, rugs etc.
• DO NOT cover or obstruct the heater in any way. Overheating will result if it is accidentally covered.
• Never immerse the product in water or any other liquids.
• DO NOT use the appliance outdoors.
• Before cleaning the appliance, ensure it is unplugged from the power and that it is completely cool.
• DO NOT clean the appliance with abrasive chemicals.
• Never use accessories that are not recommended or supplied by the manufacturer. It
could cause danger to the user or damage to the appliance.
• DO NOT insert or allow foreign objects to enter the inlet or outlet vents as this may
result in electric shock, fire or damage to the appliance.
• DO NOT install the fire using an extension cord.
• Unplug from the mains supply if the appliance is not to be used for long periods.
2.0 INSTALLATION REQUIREMENTS
The appliance is supplied with a pre-wired three pin BS1363 plug (13Amp fuse rated) and 1.7meters of electrical flex. It is therefore necessary for a suitable electrical socket to be located within this distance of the appliance and be easily accessible. The stove may be
installed on a combustible or non-combustible floor, however the heater outlet is underneath the stove and certain types of floor covering may be affected by the heat produced by the stove. The ability of the floor covering to withstand the heat produced by the stove
should be ascertained before proceeding with the installation of the stove. If in doubt then the stove should be mounted on a non-combustible hearth or plinth which extends for at least 150mm in front of the stove.This appliance should be positioned on a firm level surface. If the stove is to be sited in a fire surround then the suitability of the surround for use with electrical heaters should be established with the fire surround manufacturer.If fitted into an open draught fireplace, it is advisable to block off the chimney to reduce the
risk of draught through the stove which may cause the safety cut out system in the fan heater to operate.
3.0 APPLIANCE DATA
Supply Voltage and rating power : 220-240V AC 50Hz 1500W
Heating Elements :
750W/ 1500W
Location :
Indoor use only
Fuse Rating :
13 Amp
Lighting :
LED
Supply plug/cord : BS1363/1.7metres length
4.0 UNPACKING THE APPLIANCE
Read all the instructions before continuing to unpack or install this appliance. Carefully lift the appliance from the carton. Check
that the contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling
centre.
5.0 COMPONENT CHECKLIST
QUANTITY
1
1
1
DESCRIPTION
Stove and heater assembly
User instruction booklet
Remote control
3
© 2017 Focal Point Fires plc.
6.0 OPERATING THE APPLIANCE
Check that the fan outlet is not covered or obstructed in any way.
The appliance controls are located behind the door of the stove. The remote control functions in the same way.
7.
1. 3. 5.
1.
3.
4.
6.
2.
5.
2. 4. 6.
GB IE
1.
Power:
This button turns the appliance on/off.
The LED flame effect and fuel bed light up on the orange, medium setting (with a default speed of 19rpm).
2.
Press
Press
Press
Heater:
once for the low heat setting.
twice for the high heat setting.
a third time to turn the heat function off.
Flame Colour Effects:
3.
There are 5 different flame effects are available:
1. LED Flame effect orange.
2. LED Flame effect red.
3. LED Flame effect blue.
4. LED Flame effect purple.
5. The unit will cycle automatically between all flame effects periodically.
4.
Flame speed:
Flame speed range: Setting 1 the slowest to setting 5 the fastest: (1) -11rpm (2) -15rpm (3) -19rpm (4) -23rpm (5) -27rpm,
(CYCLE) (3) -19rpm is the default setting.
5.
Flame Brightness:
This button controls the brightness of the flame effect and the fuel bed with different 5 modes.
SPK (Speaker Function):
6.
Press once for the crackling sound to start and to light the LED fuel bed. The LED fuel bed is synchronized with the crackling
sound.
Press twice for LED burning effect to start and to turn the crackling sound off.
Press a third time to turn the LED burning effect off, and the LEDs will change from the brightest setting to the darkest setting.
7.
Thermostat Knob
Turn the control knob until the desired room temperature is achieved.
Remote Control
The fire is supplied with an IR multifunction remote.
Before the remote will operate the plastic insulating sheet
needs to be removed.
Battery Replacement
Battery Requirements: 3V CR2025
1. Locate and remove the battery bracket.
2.The battery has two sides, one with a button feature, and the
other is flat.
3. Insert the battery with the button side down into the battery bracket, making sure the battery is firmly seated.
4
© 2017 Focal Point Fires plc.
7.0 SAFETY CUTOUT SYSTEM
GB IE
This product has one non-self-resetting overheat protection device (thermal cut-out) which will activate if the air inlets or outlets are obstructed. For safety reasons the fire will NOT switch on again automatically, the following procedure must be carried
out before the fire can be operated.
NOTE: The visual effect will remain operational if the cutout is activated, only the fan heater is prevented from working.
Switch OFF the appliance at the wall socket or outlet. Leave the fire OFF for a period of no less than 10 minutes, ensuring all
obstructions are removed. Switch the appliance ON at the wall. Ensure the appliance is turned ON at the control switches. If
the fire fails to operate correctly, repeat the above procedure. If an attempt to switch on the appliance is made before the safety cutout has reset, the appliance may cutout for a further period of time. If the sequence has been followed correctly and the
appliance still fails to function, check the fuse in the wall outlet. If this is not the cause, call an electrician or maintenance engineer.
8.0 CLEANING AND MAINTENANCE
ALWAYS DISCONNECT THE APPLIANCE FROM THE MAINS SUPPLY OUTLET
SOCKET BEFORE UNDERTAKING ANY CLEANING OR MAINTENANCE!
For general cleaning use a soft clean duster - never use harsh abrasive or cleaners. The glass panels should be cleaned carefully
with a soft cloth.
If in doubt consult a qualified electrician. Refer to Section 3.0 Appliance Data for fuse specification. Excluding fuses, use only
genuine manufacturers spare parts available from your supplier.
Replacing the remote control battery:
When the battery becomes weak, the range of the remote control becomes shorter. Replace the battery with a new 3V
CR2025 lithium battery.
Note: Keep the lithium battery out of the reach of children.
9.0 SPARES
Refer to Section 3.0 Appliance Data for LED and fuse specification. Excluding fuses, use only genuine manufacturers spare parts
available from your supplier.
10.0 SERVICING
There are no internal user serviceable parts.
Check regularly for security of wall fixings as appropriate. Also check security of supply cable and connections. If the supply cable
becomes damaged, it must be replaced by a service agent or competent person, such as a qualified electrician.
This appliance is supplied with a BS1363 3 pin plug fitted with a 13 Amp fuse. Should
the fuse require replacing, it must be replaced with a fuse rated at 13 Amp and
approved to BS1362. In the event of the mains plug being removed/ replaced for any
reason, please note : IMPORTANT: The wires in the mains lead are coloured in
accordance with the following code:
Blue - Neutral
Brown - Live
Green/ Yellow - Earth
As the colours of the wires in the mains lead of this appliance may not correspond
with the colour markings identifying the terminals in your plug, proceed as follows.
The blue wire must be connected to the terminal marked with an N or coloured
black. The brown wire must be connected to the terminal marked with an L or coloured red. The green/yellow wire must be
connected to the earth terminal which is marked with an E or with the earth symbol. WARNING: Never connect live or
neutral wires to the earth terminal of the plug.
NOTE: If a moulded plug is fitted and has to be removed take great care in disposing of the plug and severed cable, it must be
destroyed to prevent engaging into a socket.
Refer to Section 3.0, Appliance Data for fuse specification. Excluding fuses, use only genuine manufacturers spare parts available
from your supplier.
5
© 2017 Focal Point Fires plc.
11.0 TROUBLESHOOTING GUIDE
Fire is not switching on
Fire is not emitting any heat
Fire shuts off after a period of time
Fire seems noisy
Remote is not operating
Ensure mains switch is on
GB IE
Replace the fuse in the plug
The fire is fitted with an energy saving thermostat. If the temperature in the room
is higher than the temperature selected on the fire, then the thermostat will stop
the heater from turning on.
Check that the temperature is not set onto the lower settings. If the room is
warm enough the thermostat will stop the fire switching the heat on.
Check that the chimney/flue is blocked off.
There is a level of noise when the flame effect is in use, caused by a motor that
helps generate the effect. This noise will be heard when there is no other
background noise.
There is a higher level of noise associated with the heater motor; this is due to
the air flow required when heat has been selected.
Before the remote will operate the plastic insulating sheet needs to be removed.
Check or replace batteries.
12.0 APPLIANCE DIMENSIONS
All dimensions in mm
6
© 2017 Focal Point Fires plc.
13.0 GUARANTEE - TERMS AND CONDITIONS
Registration is not required.
GB IE
Those specifically marked as '1 year guarantee' on the website, are guaranteed for one year from the date of purchase, provided that the following three terms and conditions are adhered to:
1. For any claim to be made within 1 year from date of purchase you will be required to provide and supply us with your original proof of purchase.
2. Your gas fire must have been commissioned by Gas Safe registered installer, evidence of which you must provide together
with the registration number.
3. All appliances must have been installed and operated in accordance with the manufacturer’s instructions.
3 Year Guarantee Terms and Conditions
The 3 year guarantee is only applicable to purchases made through an authorised stockist/retailer. Please see our website for a
list of authorised stockists. Any purchase(s) made through an unauthorised stockist(s) will be eligible for a statutory 1 year
guarantee.
For all gas fires purchased the 3 year guarantee commences from the date of purchase, provided that the following 4 terms and
conditions are adhered to:
1. For any claim to be made within the 3 years from date of purchase you will be required to provide and supply us with your
original proof of purchase.
2. Your gas fire must have been commissioned by Gas Safe registered installer, evidence of which you must provide together
with the registration number.
3. Your appliance must have been serviced annually by Gas Safe registered installer, evidence of which must be provided, such as
the receipt.
4. Purchase(s) must be made through an authorised stockist/retailer.
Please note all consumable items such as any ceramics including; coals, pebbles, the matrix, front strips, side cheeks, rear panels
and tapered rear panels are not covered by the 3 year guarantee.
During the guarantee period any product or component which is proved to be faulty or defective in manufacture, will be
repaired or replaced free of material and labour charges, providing that we have authorised or carried out the repair or
replacement.
We will not accept or reimburse the costs of any third party who undertakes any work carried on the product or fits parts,
unless we have approved such work in advance of it being carried out.
The guarantee period will not be extended even if we repair or replace any product or part.
For all electric fires purchased the 3 year guarantee commences from the date of purchase, providing that you can supply the
proof of purchase. This does not cover consumable items such as pebbles, coals or light bulbs. Purchase(s) must be made
through an authorised stockist.
Making a claim:
Making a claim is easy. If you wish to make a claim under our guarantee and all the terms and conditions for your product have
been met then please submit the following information for the attention of the 3G Service Department to the address below.
Alternatively, you can email or fax.
Focal Point Fires, 3G Service Department, Reid Street, Christchurch, Dorset, BH23 2BT.
Email: [email protected],
Fax. 01202 588639.
F861454
Details required:
1. Name, full address including postal code and contact telephone number.
2. A copy of your proof of purchase e.g. receipt or bank statement.
3. Original installers Gas Safe registration number (gas fires only).
4. Annual service receipt for every 12 months (gas fires only).
Please note that this does not affect your statutory rights.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
As our policy is one of continuous improvement and development, we therefore hope that you will understand we must retain the right to amend details and/or specifications without prior notice.
7
© 2017 Focal Point Fires plc.

advertisement

Related manuals

advertisement