Focal Point Enigma Electric Installation and User Instructions

Add to My manuals
12 Pages

advertisement

Focal Point Enigma Electric Installation and User Instructions | Manualzz
Enigma a nd M irror G lass
ELECTRIC WALL MOUNTED HEATERS
MODELS P23E
INSTALLATION AND
USER INSTRUCTIONS
Read and understand these instructions completely before commencing any assembly or installation.
Check that all components are included in the pack.
Revision D - 29.11.07
Focal Point Fires plc, Christchurch, Dorset, BH23 2BT
Tel: 01202 499330 Fax: 01202 499326
www.focalpointfires.co.uk
e-mail: [email protected]
ENIGMA
MIRROR
© 2007 Focal Point Fires plc.
CONTENTS
Page No Section Contents
Section Contents
1.0
2.0
3.0
4.0
5.0
6.0
7.0
1.0
Preliminary Notes
Appliance Data/Specifications
Electrical Installation Requirements
Site Requirements
Clearances to Combustible Materials
Unpacking the Appliance
Component Checklist
8.0
9.0
10.0
11.0
12.0
13.0
14.0
1
1
1
2
2
3
3
Page No
Preparing the Appliance
Fixing the Appliance
Operating the Appliance
Safety Cut-Out System
Maintenance - Lamp Replacement
Cleaning
Servicing
3
4
6
6
7
7
8
PRELIMINARY NOTES
The Enigma and Mirror Electric Wall Heaters provide convected heating in conjunction with a visual fuel effect
display.
The appliance is designed for indoor use, and can be flat wall mounted in the majority of wall positions anticipated. The appliance can be be located in any household room, with the exception of bathrooms. Read all of
the instructions before commencing installation. Retain for future reference and pass on as necessary to subsequent owners of the appliance.
DO NOT use this appliance immediately below a fixed socket outlet.
DO NOT use this appliance in the immediate vicinity of a bath, shower, swimming pool or other areas where
water/moisture could present a hazard.
CAUTION: This appliance must not be used in conjunction with any timer, programmer or thermal control, or
any other device that will switch on the appliance automatically, as a fire risk may occur if the heaters are accidentally covered or displaced. Note: The heater outlet is located on the top surface behind the facia.
Do not allow the heater to be covered as this may cause overheating. Additionally, DO NOT place any items on
top of this appliance. The appliance must not be placed near curtains or similar materials. A clearance space of
at least 500mm should be allowed in front of the appliance.
The electrical socket that the appliance uses MUST be easily accessible. Do not route the supply cord directly
over or above the heater unit. If the cord is damaged, it must be replaced by a service agent or competent person.
2.0
APPLIANCE DATA
Weight (kg):
Dimensions (mm):
Voltage (Volts):
Heating Elements:
Supply Cord:
Supply Plug:
Location:
Lighting:
Enigma - 14.0 kg (inc. glass facia), Mirror - 13.0kg (inc. mirror facia)
Enigma - H 690 x W 605 x D 154 (including glass facia)
Mirror - H 657 x W 485 x D 141 (including mirror facia)
230-240V a.c. 50Hz
2 x 900/1000 Watts
2 metre
BS1363, (13A BS1362 Fused)
Indoor Use Flat Wall - Non Bathroom/Shower Rooms
1 x 60W Amber bayonet connection type lamp
This appliance conforms to European Directive:
73/23/EEC Low Voltage (Safety) and CE Marking Directive.
3.0
ELECTRICAL INSTALLATION REQUIREMENTS
The appliance is supplied with a pre-wired 3-pin BS1363 plug (13 Amp fuse rated), and 2 metre cable. A standard switched outlet/wall socket, (including earth provision), must therefore be located within this distance, and
be easily accessible in order to isolate the supply for maintenance and cleaning. This socket must not be mounted behind or above the appliance. Note: the pre-wired 3-pin plug should not be removed, as this may invalidate
warranty. If you are unsure of the electrical installation requirements, seek professional advice.
It is recommended that the installation should be protected by a 30mA RCD, (Residual Circuit Device), either
via the existing main consumer unit if fitted, or by a dedicated device as part of this installation.
IMPORTANT
THIS APPLIANCE MUST BE EARTHED
The manufacturer declines all liabilities for injury to persons, or damage to property, resulting from failure to
observe this regulation, and/or failure to follow or observe these instructions.
1
© 2007 Focal Point Fires plc.
4.0 SITE REQUIREMENTS
The appliance can be flat wall mounted via the brackets on the rear panel with the fixings provided.
The wall should be relatively flat and not interfere with any of the ventilation slots in the rear panel.
The wall must be structurally sound and of a material capable of withstanding moderate heat. Finished
plaster, conventional wallpaper, dry-lined plaster board are examples of suitable materials. Materials
such as flock, blown vinyl, embossed paper and cloth wall coverings which are sensitive to even small
amounts of heat should be avoided, as some discolouration may occur.
It should be noted that the appliance creates warm convected air currents. These currents move heat
from the room surroundings to, and up the wall surfaces adjacent to the heater.
Installing the heater next to the wall coverings mentioned above or operating the heater where impurities in the air, (such as tobacco smoke, soot from candles etc) may slightly discolour wall finishing.
If the appliance is to be mounted on a dry lined or timber framed construction then the integrity and
ability of the wall to carry the weight of the appliance must be confirmed. It is important in these circumstances that any vapour barrier and/or structural members of the house frame are not damaged.
If you are unsure of the ability of the wall to carry the weight and/or which type of wall fixing to use,
you should seek professional advice and obtain the correct fixings. Alternatively, find a more suitable
wall location.
DO NOT
-
mount on a ceiling or floor or on any sloping surface.
recess any part of the appliance into the wall.
site any electrical equipment e.g. plasma screen TV sets etc, on the wall above the appliance.
site in a position where curtains or drapes could cover the appliance.
site in a position where other soft materials could cover e.g. below a coat rack.
site behind an opening door where mechanical impact/damage could occur.
site where the supply cable would become a trip hazard.
sit, stand or forcefully pull on the appliance.
obstruct, cover or force items into the openings.
use the heater to dry clothes.
site/use in an outdoor location(s).
run the supply cable under carpets or use if the plug/cable is damaged.
leave children, the infirm or elderly unsupervised, as the appliance will become hot is use.
5.0 CLEARANCES TO COMBUSTIBLE MATERIALS
It is important that the following clearances are maintained from the appliance to combustible materials. These
clearances are dependant on the mounting location as defined below:
Wall Location:
The minimum distance from the top of the appliance to a ceiling is 700mm.
The minimum distance to the sides of the appliance is 100mm.
The minimum distance to the front of the applaince is 500mm.
The appliance can be wall mounted at floor level, providing it does not stand on a carpet or similar material. Allow
clearance to carpets of 30mm.
A shelf may be mounted above the appliance provided it meets the requirements for shelves as detailed
below.
Shelf Depth
(measured from wall)
50mm
100mm or 152mm
Minimum Shelf Distance
(measured from top of appliance, not the frame)
390mm
490mm
Note: the ability of any shelf to withstand prolonged moderate heat, eg 80°C must be assured.
Floor/Fireplace Wall Location:
If mounted into a fireplace surround, ensure that the minimum clearance distances to mantles and/or any shelves
fitted above the appliance are as specified above.
Note: the ability of any fireplace or surround to withstand prolonged moderate heat, eg 80°C must be assured.
2
© 2007 Focal Point Fires plc.
6.0
UNPACKING THE APPLIANCE
Caution: This appliance is heavy. Always seek assistance whilst unpacking and/or during installation.
Read all the instructions before continuing to unpack or install this appliance. Carefully remove the appliance
from its packaging and stand on the floor.
Note: DO NOT stand the appliance unfixed with its front facia fitted, as this will be unstable.
Check that the remaining packaging contents correlate with the component checklist below. Please dispose of
all packaging with care at your local recycling centre.
7.0
COMPONENT CHECKLIST
QUANTITY
1
1
1
1
1
1
8.0
DESCRIPTION
Fire Appliance
Glass Facia and Four Decorative Corner Colums or Mirror Facia
Bag of Decorative Pebbles
Instruction Booklet
Screw Fixing Pack (3 x 37mm long round head screws and 3 plastic wall plugs)
Wall Mounting Template
PREPARING THE APPLIANCE
CAUTION: DO NOT connect the appliance to the supply at this stage.
1. Place the appliance on a suitable surface and remove the 2 x No 8 Phillips
self tapping screws, retaining the lower lamp cover plate, as shown in figure 1.
Remove the cover plate by sliding towards the top of the appliance and then
easing from its lower retaining slot.
2 off No 8 fixing screws
Lamp cover
plate
Fig 1
2. Carefully “ease” the white fuel bed from the appliance as shown in
figure 2. Be careful not to damage the spinner or lamp during
removal.
Fig 2
This allows access to the lower fixing position of the rear bracket
attached to the back of the main case assembly. See figure 3
Lower fixing
position
3
Fig 3
© 2007 Focal Point Fires plc.
9.0
FIXING THE APPLIANCE
Having selected the final mounting position for the appliance, taking
into account the site requirements as detailed in sections 1.0 - 5.0, the
heater can now be fixed to the wall.
Remove any protective film coatings from the finished/decorative surfaces of the appliance. To ensure customer safety, be sure to design the
installation so that the strength of both the wall and any wall fixings
used are sufficient.
Focal Point Fires plc. assumes absolutely no responsibility for injuries
and damages that may occur due to improper installation or handling.
The appliance should not be installed until all wet plastering and/or dry
wall sanding and wall painting has been completed. Do not block the
ventilation holes of the appliance. The wall onto which the appliance is
installed must be flat. Install only on a vertical surface. Avoid sloped surfaces. Installation onto anything other than a vertical wall may result in
fire, damage or injury.
WARNING
THE WALL WHERE THE APPLIANCE IS TO
BE INSTALLED MUST BE CAPABLE OF
LONG-T
TERM SUPPORT OF THE TOTAL
LOAD OF THE APPLIANCE. MEASURES
SHOULD ALSO BE TAKEN TO ENSURE SUFFICIENT STRENGTH TO WITHSTAND THE
FORCE OF EARTHQUAKES, VIBRATION
AND OTHER EXTERNAL FORCES.
WARNING
INCORRECT INSTALLATION CAN CAUSE
THE APPLIANCE TO FALL FROM THE WALL
AND RESULT IN FIRE, DAMAGE OR INJURY.
If the appliance is to be mounted on the inner leaf of a conventional cavity brick wall, or a solid wall, then the
wall plugs and fixing screws provided may be used. Depending on the condition of the wall it may be necessary
to use alternative fixings than the ones provided. If you are unsure, seek professional advice.
If the appliance is to be mounted on a dry lined wall or a timber framed
construction wall then efforts should be made to fix in at least one positions vertically, into one of the wooden studs, or supporting wooden
members of the wall using two of the fixing screws provided. If this is
not possible then the wall should be strengthened using appropriate
building materials.
WARNING
PLASTERBOARD ALONE IS NOT CONSIDERED TO BE A STRUCTURAL MATERIAL. IT IS
NOT RECOMMENDED TO RELY ON PLASTERB O A R D FIXINGS ALONE TO SUPPORT THE WEIGHT OF THE APPLIANCE.
If there is no alternative than to rely on some plasterboard fixings then special
cavity screw fixings or hollow wall anchors will be required which are not supplied with this product. These should be constructed from metal and not plastic and of the design indicated in figure 4. If you are unsure, seek professional
advice.
Fig 4
a) Marking Positions:
There are three fixing positions, two upper “hanging” positions”, and one lower position on the back-panel located behind the fuel bed. A template is provided to aid location of fixings. Use a spirit level to ensure that the template is level. This ensures that both upper and lower fixing positions are horizontally aligned.
Using the template in the required position on the wall, “mark through” the template and onto the wall at the
three mounting locations designated “P23E” for this particular appliance. Now remove the template.
b) Wall Fixings:
If the appliance is to be mounted on the inner leaf of a conventional cavity wall or a solid wall, drill three holes
using a 7.0mm masonry bit, to a depth equal to the wall plug, ie 37mm.
Insert the wall-plugs provided and ensure that they are flush with the wall. If the appliance is to be mounted on
a dry lined wall or timber framed construction, then special cavity screw fixings will be required, that are not supplied with this product. Insert 2 x 37mm long fixing screws into the upper two wall-plugs, taking care to leave
4
© 2007 Focal Point Fires plc.
FIXING THE APPLIANCE (continued)
the screws protruding approximately 6mm from the wall.
The appliance can now be “hung” onto the two upper wall fixings, ensuring that the heads of the screws go
through the keyhole shaped holes, and then drop down into the keyhole upper slot.
Ensure that the lower rear panel fixing hole aligns with the wall plug, and then insert 1 x 37mm long fixing screw
and fully tighten.
Finally fully tighten the two upper fixing screws, through the two panel access holes at the front of the appliance,
and ensure that the appliance is firmly and securely attached to the wall.
c) Re-aassembly of Appliance:
Note: re-assembly is the reverse of disassembly as described in section 8.0
1. Refit the fuel bed, ensuring that the lamp spinner is free to rotate, see previous figure 2.
2. Refit the lower lamp cover plate, firstly inserting the bottom edge behind the lower firebox lip. Secure with
the two screws previously removed, see previous figure 1.
3. Finally, peel off any remaining protective plastic coatings on the front frame, curved backpanel and the plastic fuel bed.
d) Placement of Pebbles:
Unpack the pebbles and arrange them over the fuel bed. The final
pebble arrangement can only be done later when the lamp is
switched on and light shines up through the transparent cover.
The ideal pebble layout is shown in figure 5.
Fig 5
Ensure that all pebbles are placed such that they avoid any danger
from falling off the appliance.
e) Hanging the Front Glass or Mirror Facia :
Remove the glass or mirror facia panel from its protective packaging.
The facia panel is supported on the appliance by four M6 screws which
protrude from brackets on the front of the outer casing.
See figure 6. Note glass facia shown, mirror facia attaches in identical way.
Ensure each screw is
unscrewed approximately
one turn from the fully
screwed in position in order
to create a 2mm gap.
See figure 7.
2mm
Fig 7
Fig 6
Simply hang the facia panel onto the outer casing ensuring that the corresponding keyhole shaped holes engage
the screwheads fully.
5
© 2007 Focal Point Fires plc.
FIXING THE APPLIANCE (continued)
f) Fitting the Decorative Corner Columns - Enigma Facia only:
Front clamping disc
To fit the decorative corner columns, ensure the main glass facia is
mounted in position. Remove any transit tape and unscrew the front
clamping disc and remove. Refer to figure 8, and compress the column assembly. Then position behind the glass panel, lining up with
the appropriate hole.
Release the assembly when in position and secure in place by refitting the front clamping disc. Repeat for the other three columns.
10.0
Fig 8
Compress the
assembly
OPERATING THE APPLIANCE
Read All Instructions Before Use
Check that the heater outlet grille, mounted at the top of the appliance, is not covered or obstructed in any way,
and ensure the power to the fire is switched on. The appliance is controlled using four switches mounted at the
right hand side towards the top.
Control Switches:
The first switch towards the front, marked (0I), controls the main power
to the appliance and switches on the visual light display. This feature
can be used independently of the heating features.
WARNING
The next switch marked (*) operates the fan blower without heat, and
can be used for cool air circulation. However for this feature, the main
power switch (0I), must also be in the “on” position.
THIS APPLIANCE IS A HEATER, AND AS
SUCH THE TOP MOUNTED AIR OUTLET
GRILLE AND SURROUNDING AREAS WILL
GET HOT.
The next switch with a “single bar” marked (I) operates the low heat,
(1kW), setting.
WHEN IN USE, DO NOT TOUCH THESE
AREAS AND SUPERVISE/KEEP CHILDREN
AWAY FROM THE APPLIANCE.
The switch with “two single bars” marked (II), operates the high heat, (2kW) setting.
To operate the fire in any of the above modes, the front switch marked (OI) must be switched to the “on” position.
To operate the fire, the first switch must be turned on firstly, followed by the second switch to start the blower,
if required. To obtain heat from the appliance, the I switch must then be operated for LOW heat, followed by the
II switch for the HIGH heat setting.
The appliance can be switched off at any time, irrespective of the particular mode selected, by simply switching the first switch marked (OI) to the “off” position.
It is also recommended to unplug the power supply cable at the supply outlet when not in use.
11.0
SAFETY CUT-O
OUT SYSTEM
This appliance has a safety cut-out system fitted which will activate if the air inlets or heater outlets are obstructed. For safety reasons the fire WILL NOT switch on again automatically.
NOTE: The visual light effect will remain operational if the cut-o
out is activated, only the fan heater elements are
prevented from operating.
The following procedure must be carried out before the fire can be operated again:
1. Unplug the power supply cable at the outlet socket and place all switches to off at the appliance.
6
© 2007 Focal Point Fires plc.
SAFETY CUT-O
OUT SYSTEM (continued)
2. Leave the fire OFF for a period of not less than 10 minutes, ensuring any obstructions are removed.
3. Plug in the power supply cable at the outlet socket, and then switch on at the appliance.
If the appliance fails to operate correctly, repeat the above procedure.
If an attempt to switch on is made before the safety cut-out has reset, the heaters may cut-out for a further period of time. If the sequence has been followed correctly and the heaters still fail to function, check the power
supply cable plug is plugged in at the outlet socket. If this is not the cause, call an electrician.
12.0
MAINTENANCE and LAMP REPLACEMENT
ALWAYS DISCONNECT/ISOLATE THE APPLIANCE AT THE SUPPLY/OUTLET SOCKET AND ALLOW TO
COOL BEFORE UNDERTAKING ANY MAINTENANCE.
Excluding the lamp and fuse, use only genuine spare parts available from your supplier. Replacement lamps must
be of the same wattage and specification as those stated in Section 2.0 Appliance Data/Specifications.
Replacing the Light Bulb.
1. Switch off at the appliance, and then disconnect the plug
from the outlet socket.
2. Remove the front facia and then remove the lower lamp
cover plate (2 x screws), as described in section 8.0 to gain
access to the bulb.
Note: the fuel bed can be removed if necessary to aid replacement.
Fig 9
3. The bulb has a conventional bayonet fitting. Remove and
replace with the new bulb (see Fig 9 opposite).
4. Reposition the lower lamp cover plate and replace the two No 8 POZI screws, and tighten fully.
5. Re-connect electrical supply and check for correct operation of the lamp and spinner assembly. Replace the
front facia.
13.0
CLEANING
ALWAYS DISCONNECT/ISOLATE THE APPLIANCE AT THE SUPPLY/OUTLET SOCKET AND ALLOW TO
COOL BEFORE UNDERTAKING ANY CLEANING.
Regularly clean around the appliance to ensure that dust, fluff, pet hair/dander etc, are kept to a minimum.
There are no other specific requirements for care, other than regular cleaning of the general appliance. A wipe
with a dry cloth is normally sufficient.
DO NOT use abrasive cleaners as they can damage the finish. Aluminium parts may be cleaned using an appropriate metal cleaner. Test on a hidden part before cleaning. Clean only in the direction of the grain.
Glass or Mirror Facia Panel - This should only be cleaned using a suitable glass cleaner. Test on a small area first.
7
© 2007 Focal Point Fires plc.
14.0
SERVICING
There are no internal user serviceable parts.
Check regularly for security of wall fixings and front facia as appropriate. Also check the security and condition
of the supply cable and connections. If the supply cable becomes damaged, it must be replaced by a service
agent or competent person, such as a qualified electrician.
The wires in the cable are coloured in accordance with the
following code:
LIVE
NEUTRAL
EARTH
-
Brown
Blue
Green/Yellow
Fuse Replacement:
Use an approved fuse to BS 1362 and proceed as follows:
1. Remove the fuse cover (A) and fuse (B). See Fig 10.
2. Fit replacement 13A fuse into fuse cover, and then refit both into plug.
If the fuse cover (A) is missing or lost the plug must not be used until a replacement
is fitted. Replacements are available from your local electrical store
Fig 10
Before Calling the Manufacturer
You will be charged for a Service Engineers visit if a problem with your appliance is caused by incorrect
installation, incorrect use, or damage caused by use of ancillary equipment not defined as suitable in this
instruction manual.
Please Note : Except where otherwise stated, all rights, including copyright
in the text, images and layout of this booklet is owned by Focal Point Fires
plc. You are not permitted to copy or adapt any of the content without the
prior written permission of Focal Point Fires plc.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice
As our policy is one of continuous improvement and development, we hope therefore you will understand we must retain the right to amend details and/or specifications without prior notice.
8
F860099
© 2007 Focal Point Fires plc.
© 2007 Focal Point Fires plc.
All dimensions in mm
304
416.5
159
605
690
Enigma - Appliance Views and Dimensions
9
© 2007 Focal Point Fires plc.
© 2007 Focal Point Fires plc.
All dimensions in mm
416.5
141
304
485
657
Mirror - Appliance Views and Dimensions
10
© 2007 Focal Point Fires plc.

advertisement

Related manuals

Download PDF

advertisement