Pulsar VD50 Instructions

Pulsar VD50 Instructions
CAL. VD50
1/10 SECOND RETROGRADE CHRONOGRAPH
l Hour, minute and second hands
l Date displayed in numerals
STOPWATCH
l Measures up to 60 minutes in 1/10 second increments.
ENGLISH
TIME/CALENDAR
DISPLAY AND CROWN/BUTTONS
STOPWATCH
1/10-second hand
Minute hand
English
Hour hand
A
STOPWATCH
minute hand
a
b
c
CROWN
Date
Second hand
B
STOPWATCH
second hand
2
a: Normal position
b: First click
c: Second click
SCREW DOWN CROWN
[for models with screw down crown]
Unlocking the crown
1 Turn Crown counterclockwise until you no
longer feel the threads turning.
2 Crown can be pulled out.
1 Push Crown back in to normal position.
English
Locking the crown
2 Turn Crown clockwise while pressing it
lightly until tight.
3
ADJUSTING THE STOPWATCH HAND POSITION
l Before setting the time, be sure to check that the STOPWATCH hands are in
the “0” position when the stopwatch is reset (for resetting the stopwatch, see
"STOPWATCH").
STOPWATCH
1/10-second
hand
CROWN
s
English
* If any of the STOPWATCH hands do not return to the "0" position when the stopwatch is reset, follow the procedure below to reset the hands.
A
A
s
B
4
STOPWATCH
minute hand
STOPWATCH
second hand
Press repeatedly to reset the
STOPWATCH 1/10 second
hand to the “0” position.
Press repeatedly to reset the
STOPWATCH second and minute hands to the “0” position.
s
B
Pull out to second click
CROWN
Push back in to normal
position.
TIME/CALENDAR SETTING
Minute hand
Second hand
Hour hand
Date
1 Pull out to first click, and turn clockwise until the previous day’s date
appears.
2 Pull out to second click when Second hand is at the 12 o’clock position.
3 Turn clockwise until the desired date appears.
4 Turn to set Hour and Minute hands.
5 Push back in to normal position in accordance with a time signal.
English
CROWN
5
STOPWATCH
English
l The stopwatch can measure up to 60 minutes in 1/10 second increments.
l The measured time is indicated by the STOPWATCH hands that move independently of the center hands.
l Before using the stopwatch, be sure to check that the crown is set at the normal position and that the STOPWATCH hands are reset to the “0” position.
* If the STOPWATCH hands do not return to the "0" position when the stopwatch is
reset, follow the procedure in "ADJUSTING THE STOPWATCH HAND POSITION"
to reset the hands..
STOPWATCH
minute hand
STOPWATCH
second hand
6
STOPWATCH
1/10-second hand
A Start / Stop / Restart
B Reset
Standard measurement
A
s
s
A
B
RESET
STOP
START
Accumulated elapsed time measurement
STOP
B
RESET
Movement of the STOPWATCH 1/10 second hand
English
RESTART
A
s
STOP
A
s
A
s
START
s
A
l After the measurement exceeds 1 minute, the STOPWATCH 1/10 second
hand stays at the "0" position while the stopwatch is counting.
l When the measurement is stopped, the hand moves to indicate the elapsed
1/10 seconds.
7
NOTES ON OPERATING THE WATCH
ADJUSTING THE STOPWATCH HAND POSITION
l The STOPWATCH minute hand moves correspondingly with the STOPWATCH
second hand.
English
l The STOPWATCH hands move quickly if the respective buttons are kept pressed.
8
TIME/CALENDAR SETTING
l It is necessary to adjust the date on the first day after a 30-day month and February.
l Do not set the date between 9:00 p.m. and 1:00 a.m., as the date may not change
properly. If it is necessary to set the date during that period of time, first change the
time to any time outside of this period, set the date, and then reset to the correct
time.
l Do not press any button when the crown is at the second click position, as this will
move the STOPWATCH hands.
l When setting the hour hand, be sure to check that AM/PM is correctly set. The
watch is designed so that the date changes once in 24 hours.
* Turn the hands past the12 o’clock marker to determine whether the watch is set
for the A.M. or P.M. period. If the date changes, the time is set for the A.M.
period. If not, the time is set for the P.M. period.
l When setting the minute hand, first advance it 4 to 5 minutes ahead of the desired
time and then turn it back to the exact minute.
STOPWATCH
l Restart and stop of the stopwatch can be repeated by pressing button A.
2
Years
Battery life : Approx. 2 years
Battery
: SEIKO SR920SW
English
BATTERY CHANGE
l If the stopwatch is used for more than 2 hours a day, the battery life may be less
than the specified period.
l As the battery is inserted at the factory to check the function and performance of
the watch, its actual life once in your possession may be less than the specified
period.
l When the battery expires, be sure to replace it as soon as possible to prevent any
malfunction.
9
l We recommend that you contact an AUTHORIZED PULSAR DEALER for battery
replacement.
English
l Battery life indicator
10
When the battery nears its end, the second hand moves at two-second intervals
instead of normal one-second intervals. In that case, have the battery replaced with
a new one as soon as possible.
* The watch remains accurate while the second hand is moving at two-second
intervals.
l Necessary procedure after battery change
After the battery is replaced with a new one, or in case any of the hands should
move improperly, follow the procedure below to reset the STOPWATCH hands to “0”
position.
CROWN
A
s
A
and
B
s
s
B
s
CROWN
s
* The STOPWATCH minute
hand moves correspondingly with the STOPWATCH
second hand.
* The STOPWATCH hands
move quickly if the respective buttons are kept
pressed.
A
CROWN
Press and hold simultaneously
for 2 seconds or longer.
* The STOPWATCH second hand
turns counterclockwise, and then
returns to where it was.
Press repeatedly to set the
STOPWATCH 1/10 second
hand to the “0” position.
English
B
Pull out to second click.
Press repeatedly to set the
STOPWATCH second and minute
hands to the “0” position.
Turn to set the time.
Push back in to normal position.
11
WARNING
l Do not remove the battery from the watch.
l If it is necessary to take out the battery, keep it out of the reach of
children. If a child swallows it, consult a doctor immediately.
English
l Never short-circuit, tamper with or heat the battery, and never expose it to fire. The battery may burst, become very hot or catch fire.
CAUTION
l The battery is not rechargeable. Never attempt to recharge it, as this
may cause battery leakage or damage to the battery.
12
TO PRESERVE THE QUALITY OF YOUR WATCH
WATER RESISTANCE
l Water resistance (5 bar)*
English
If “WATER RESISTANT 5 BAR”
l Non-water resistant
is inscribed on the case back,
If “WATER RESISTANT” is not
your watch is designed and
inscribed on the case back, your
manu-factured to withstand up to
watch is not water resistant, and
care should be taken not to get 5 bar and is suitable for swimming, yachting and
it wet as water may damage the movement. If taking a shower.
the watch becomes wet, we suggest that you l Water resistance (10 bar/15 bar/20
bar)*
have it checked by an AUTHORIZED PULSAR
If “WATER RESISTANT 10 BAR”,
DEALER or SERVICE CENTER.
“WATER RESISTANT 15 BAR” or
l Water resistance (3 bar)
“WATER RESISTANT 20 BAR” is
If “WATER RESISTANT” is inscribed
inscribed on the case back, your
on the case back, your watch is watch is designed and manufactured to withstand
designed and manufactured to up to 10 bar/15 bar/20 bar and is suitable for taking
withstand up to 3 bar, such as acci­ a bath, shallow diving, but not for scuba diving.
dental contact with splashes of water or rain, but it We recommend that you wear a PULSAR Diver’s
is not designed for swimming or diving.
watch for scuba diving.
13
English
* Before using the water resistance 5, 10, 15 or 20 bar watch in water, be sure the
crown is pushed in completely.
Do not operate the crown when the watch is wet or in water. If used in sea water,
rinse the watch in fresh water and dry it completely.
* When taking a shower with the water resistance 5 bar watch, or taking a bath with
the water resistance 10, 15 or 20 bar watch, be sure to observe the following:
• Do not operate the crown when the watch is wet with soapy water or shampoo.
• If the watch is left in warm water, a slight time loss or gain may be caused. This
condition, however, will be corrected when the watch returns to normal temperature.
NOTE:
Pressure in bar is a test pressure and should not be considered as
corresponding to actual diving depth since swimming movement
tends to increase the pressure at a given depth. Care should also be
taken on diving into water.
TEMPERATURES
Your watch works with
stable accuracy within a
temperature range of 5
° C and 35° C (41° F and
95° F).
Temperatures over 60° C (140° F)
14 may cause battery leakage or short-
en the battery life. Do not leave
your watch in very low temperatures
below –10° C (+14° F) for a long
time since the cold may cause a
slight time loss or gain.
However, the above conditions will
be corrected when the watch returns to normal temperature.
MAGNETISM
Your watch will be adversely affected by strong
magnetism. Keep it away
from close contact with
magnetic objects.
SHOCKS & VIBRATION
CARE OF CASE AND BRACELET
To prevent possible rusting of
the case and bracelet caused
by dust, moisture and perspiration, wipe them periodically
with a soft dry cloth.
PERIODIC CHECK
Be careful not to expose
the watch to solvents,
mercury, cosmetic spray,
detergents, adhesives or
paints. Otherwise, the
case, bracelet, etc. may become
discolored, deteriorated or damaged.
English
It is recommended that the
Light activities will not
watch be checked once
affect your watch, but be
every 2 to 3 years. Have
careful not to drop your
your watch checked by an
watch or hit it against
AUTHORIZED PULSAR
hard surfaces, as this
DEALER
or
SER­V ICE CENTER to
may cause damage.
ensure that the case, crown, buttons,
gasket
and
crystal
seal remain intact.
CHEMICALS
PRECAUTION REGARDING
CASE BACK PROTECTIVE FILM
If your watch has a
protective film and/or a
sticker on the case back,
be sure to peel them off
before using your watch.
15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement