Massive Audio PX6 Amplifier Product Manual


Add to my manuals
15 Pages

advertisement

Massive Audio PX6 Amplifier Product Manual | Manualzz
Primo Series Amplifiers
P2/P3/P4/P8
PX 4 / PX 4 S/ PX 4 R
PX 2 R/ PX 6
(PX4S)
1. Speakers
Connect speakers/subwoofers to these terminals. Be sure to check wiring for
properpolarity. Never connect the speaker cables to chassis ground.
2. +12 Volt Power
Connect this terminal through a fuse or circuit breaker to the positive terminal
of the vehicle battery or the positive terminalofan isolated audio system battery.
3. AUTO SENSING TURN ON FUNCTION / REM OUT (HI- INPUTS)
When using hi-input, the amp can detect the dc offset (Hi-Inputs) from the high
level input signal to auto turn on/off. When the amp turns on, the rem terminal will
output +12V DC tocontroltheother device turnon/off.
Rem in: when use low level input, the amp rem in should be connected to the rem
out of the source unit. The head unit controls the amp turn on/off.
4. GND
Connect this cable directly to the frame of the vehicle. Make sure the metal
frame has been stripped of all paint down to the bare metal.
use the shortest distance possible. It is always a good idea to replace the
factory ground at this time with a larger cable eoual to the new directly to the
vehicle battery ground terminal or any other factory ground points.
5. RCA INPUT / AUTO HI-LOW LINE CONVERTOR
These rca input jacks connect with your source unit rca low level outputs
or via optional adapter with your source unit speaker high level outputs. The use of
high quality of twisted pair car audio cables is recommended to prevent the
possibility disturbance of the audio signal.
6. REMOTE (MONO BLOCK)
Connect the remote controller to control the subwofer amplifier volume from
the driver seat location.
7. GAIN CONTROL (MONO BLOCK)
The gain control will match the amplifiers sensitivity to the source units signal
voltage. The operating range is 10V to 4oomV. this is not a volume control!
8. LOW PASS FILTER CONTROL ( P2 , P3 , P4 , P8 , PX4 , PX4S , PX6 )
This control is used to select the desired low pass x-over frequency . The
frequency can be adjusted from 60hz to 220hz for all bass mono models .
9. SUBSONIC FILTER CONTROL ( P2 , P3 , P4 , P8, PX4S , PX6 )
This control can filter out unwanted low frequencies from ohz (off) to 60hz.
This function will increase the power handling of your woofers.
10. BASS BOOST LEVEL KNOB ( MONO BLOCK)
This control adjusts the boost level of the bassboost center frequency. It can
be adjusted from 0 to 12db . combining with bassboost frequency, you can
accurately match the amplifiers performance to woofer response .
11. BASS BOOST FREQ KNOB ( MONO BLOCK )
This controls the boosted center frequency. The frequency can be adjusted
from 30hz to120hz according to your cars audio system performance. (eg. when
you adjust this knob to 50hz, amplifier will boost the frequency around 50hz).
This function should be adjusted in combination with bass boost level tuning .
12. X-OVER MODE ( FULL RANGE )
This switch works together with the freq to adjust the operating frequency range
of the amp. When switch to LPF or HPF, the corresponding filter can adjust the operating
frequency range between 10hz to 300hz ( or 10ohz to 3khz ) . When pushing the subwoofer,
please switch to lpf mode when pushing small caliber full frequency speaker, middle and
high frequency loudspeaker , please switch to hpf mode . When pushing large caliber
full frequency speakers , please switch to full mode . When switched to full mode ,
the filters will not function.
warning : use buttons and hpf knob correctly to prevent low frequency damage to
tweeters.
13. FREQUENCY CONTROL ( PX4 , PX4R , PX2R )
These switches work with the crossover. The x1 & x10 buttons are for High pass & low
pass frequency adjustments. When this button is set at the “x1” the hpf/lpf range is from
10hz-300hz. When this button is set at the “x10” position, the range adjustments are
100hz-3khz.
Caution: use hpf & lpf buttons and knobs correctly to prevent incorrect frequency
damage to corresponding drivers.
14. FREQUENCY CONTROL ( PX4S )
x1 & x18 buttons are used for high pass and low pass frequency adjustments.
These buttons work with the crossover. For hpf: when this button is set at the “x1” the
range is from 20hz-334hz. When this button is set at the “x18” position, the range
adjustments are 360hz-6khz. For lpf: the “x1” range is from 50hz-550hz and the
“x18” range is from 550hz-6khz.
Caution: use hpf & lpf buttons and knobs correctly to prevent incorrect frequency
damage to corresponding drivers.
15. EXTERNAL CAPACITOR INPUT
For connecting an optional (sold separately) external hi-voltage capacitor .
This will help stabilize the amplifiers needed voltage during operation while improving
fidelity and maximizing head room.
16 . POWER / PROTECTION
This led will light up when the amplifier is working properly.
When the led is blue, the amplifier is in safe operation . When the led is red the
amplifier is in protection mode .
17 . AUTO SENSING TURN ON INDICATOR
The LED will light up blue when the ato is being used (automatic turn on).
18. 2 / 4 CH SWITCH ( RX4S )
Set this switch in conjunction with how many input cables are being used, in the 2
channel setting all four outputs will be activated.
19. CLIP
The LED indicator is to show signal clipping if the input signal wave is beyond the range.
By lowering the gain, the clipped portion will go back within the input range and the
led indicator will turn off.
Occasional led “on ” (0ccasional flickering) of the led would be permissible in some
installs or based on personal preference.
P2/P3/P4
P2/P3/P4
P8
P8
Fig 2. 4-CH AMPLIFIER PANEL LAYOUT
PX4
PX4S
PX4R
PX4/PX4S/PX4R
Fig 3. 2-CH AMPLIFIER PANEL LAYOUT
2R
5
PX2R
2R
PX2R
Fig 4. 6-CH AMPLIFIER PANEL LAYOUT
PX6
PX6
Fig 5. MONO AMPLIFIER WIRING
(SINGLE WOOFER LOAD)
P2/P3/P4/P8
Fig 6.
4 OHM
4 OHM
Two DUAL 4-Ohm SUB
Fig 7. PX4/PX4S/PX4R AMPLIFIER WIRING
(3-CHANNEL MODE)
2 OHM-4 OHM 2 OHM-4 OHM
2 OHM MINIMUM STEREO
4 OHM MIN BRIDGED
4 OHM-8 OHM
Fig 8. PX4/PX4S/PX4R AMPLIFIER WIRING
(4-CHANNEL MODE)
2 OHM-4 OHM 2 OHM-4 OHM
2 OHM-4 OHM 2 OHM-4 OHM
Fig 9. PX2R amplifi er wiring
(2-CHANNEL MINIMUM)
2 OHM MINIMUM STEREO
2R
2 OHM-4 OHM 2 OHM-4 OHM
2R
5
Fig 10. PX6 amplifi er wiring
(6-CHANNEL MODE)
6 CH FULL RANGE DIGITAL
2 OHM MINIMUM EACH CHANNEL
2 OHM-4 OHM 2 OHM-4 OHM 2 OHM-4 OHM
2 OHM-4 OHM 2 OHM-4 OHM 2 OHM-4 OHM
700x1
500x1
400x1
250x1
N/A
2 Ohm RMS Power (Watt)
4 Ohm RMS Power (Watt)
4 Ohm Bridged Power (Watt)
N/A
P4
P8
200A
5.9"
8.34"
19.9“
LENGTH
13.46"
1.9"
WIDTH
Dimension (INCHS)
HEIGHT
9.13"
50A
80A
9.4"
SMT PARTS / DOUBLE SIDE FR4 PCB
220A
Compoents & PCB
160A
PROTECT AT 80C /176F
100A
90A
60A
N/A
2 OHM
FIXED
0 -12DB
>110dB
20Hz-6kHz
Overheat Protection Temperature
6.7"
60A
Recommend Extenal Fuse
60A
40A
300A
Current Drawn @ MAX Power
170A
70A
Current Drawn @ RMS Power
110A
PASS
50A
Short Circuit Test @ Max Power
YES PROTECT < BV
YES (HIGH INPUTS)
N/A
2 OHM
FIXED
0 -12DB
>110dB
<0.03%
50Hz-750Hz
Low Voltage Protection
120A
Optional Remote
80A
YES
Minium Load
Auto Turn On
30Hz-120Hz
1 Ohm(Only P8 is 0.5 Ohm)
BassBoost FREQ.
>100dB
0 -12DB
S/N Ratio
BassBoost Level
THD @ 4 ohm load, 30% Rated Power
0-60Hz
SubSonic Filter (HPF)
50Hz-6kHz
20Hz-45kHz
15Hz-25kHz
50Hz-750Hz
60Hz-220Hz
LPF
400x2
150x4
240x4
N/A
N/A
400mV-10V(hi inputs or low inputs)
300x2
100x4
150x4
N/A
N/A
4 -CHANNEL
PX4S
10Hz-220Hz
FEATURES
N/A
1000x1
1400x1
2300x1
3500x1
PX4
4 -CHANNEL
Power output @ 14.4V
MONO
BLOCK
Input Level
N/A
700x1
1000x1
1600x1
N/A
MONO
BLOCK
Frequency Response
N/A
1000x1
N/A
600x1
1 Ohm RMS Power (Watt)
Description
0.5 Ohm RMS Power (Watt)
P3
MONO
BLOCK
P2
MONO
BLOCK
MODEL
10.15"
140A
150A
100A
N/A
2 OHM
FIXED
YES
>110dB
20Hz-6kHz
50Hz-6kHz
20Hz-45kHz
700x2
250x4
350x4
N/A
N/A
4 -CHANNEL
PX4R
10.15"
140A
150A
100A
N/A
2 OHM
FIXED
0 -12DB
>110dB
20Hz-6kHz
50Hz-6kHz
20Hz-45kHz
1400x1
500x2
700x2
N/A
N/A
2 -CHANNEL
PX2R
11.81“
140A
150A
100A
N/A
2 OHM
FIXED
0 -12DB
>110dB
20Hz-6kHz
50Hz-6kHz
20Hz-45kHz
350x3
130x6
180x6
N/A
N/A
6 -CHANNEL
PX6
13
P . O . BOX 252004
Los Angeles, CA 90025 U.S.A.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • 6-channel configuration for powering up to six speakers/subwoofers
  • Compact design for easy installation in various vehicles
  • High-quality sound reproduction for an immersive audio experience
  • Variable crossover/EQ settings to tailor the sound to your preferences
  • Protection circuitry to safeguard the amplifier and your speakers

Related manuals

Frequently Answers and Questions

How many channels does the PX6 have?
The PX6 has 6 channels.
What is the power output of the PX6?
The power output of the PX6 varies depending on the impedance of the connected speakers.
What type of speakers can I connect to the PX6?
You can connect a variety of speakers to the PX6, including subwoofers.
What are the dimensions of the PX6?
The dimensions of the PX6 are not specified in the provided manual.

advertisement