Aten VE2812EUT Video Extender User Manual
ATEN VE2812UST offers superior quality transmission of HDMI and VGA signals over a single Cat 5e/6/6a cable. The device supports Long Reach Mode, enabling transmission distances of up to 150 m at 1080p resolution. With built-in Power over HDBaseT (POH) functionality, it can supply power to compatible receivers from the transmitter unit itself. Additionally, the VE2812UST provides RS-232 and IR signaling pass-through for remote device control.
Advertisement
Advertisement
VE2812UST / VE2812EUT
HDMI & VGA HDBaseT Transmitter with US / EU Wall Plate
User Manual
www.aten.com
VE2812UST / VE2812EUT User Manual
EMC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Caution
: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
CE Warning
: Operation of this equipment in a residential environment could cause radio interference.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Suggestion
: Shielded twisted pair (STP) cables must be used with the unit to ensure compliance with FCC & CE standards.
Achtung:
Der Gebrauch dieses Geräts in Wohnumgebung kann
Funkstörungen verursachen.
KCC Statement
ii
RoHS
This product is RoHS compliant.
VE2812UST / VE2812EUT User Manual
User Information
Online Registration
Be sure to register your product at our online support center:
International http://eservice.aten.com
Telephone Support
For telephone support, call this number:
International
China
Japan
Korea
North America
886-2-8692-6959
86-400-810-0-810
81-3-5615-5811
82-2-467-6789
1-888-999-ATEN ext 4988
1-949-428-1111
User Notice
All information, documentation, and specifications contained in this manual are subject to change without prior notification by the manufacturer. The manufacturer makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties as to merchantability or fitness for any particular purpose. Any of the manufacturer's software described in this manual is sold or licensed
as is
.
Should the programs prove defective following their purchase, the buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV interference caused by unauthorized modifications to this device. It is the responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT
BEFORE USE.
iii
VE2812UST / VE2812EUT User Manual
Package Contents
1 VE2812UST / VE2812EUT HDMI & VGA HDBaseT Transmitter
1 3-Pin RS-232 Terminal Block
1 2-Pin Power Terminal Block
1 Mounting Kit (VE2812EUT only)
1 Faceplate (VE2812UST only)
1 Power Adapter
1 User Instructions
Note:
Make sure that all of the components are present and in good order. If anything is missing or was damaged in shipping, contact your dealer.
iv
VE2812UST / VE2812EUT User Manual
Table of Contents
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
1. Introduction
Compatible ATEN Video Extenders . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Hardware Setup
Mounting the VE2812UST / VE2812EUT Unit . . . . . . . . . . . . . . . . . . . . . . 7
Drawing Screw Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
VE2812UST Wall Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
VE2812EUT Wall Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting the VE2812UST / VE2812EUT Unit. . . . . . . . . . . . . . . . . . . . 10
Terminal Block Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power Supply Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
RS-232 Channel Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3. Operation
Input Selection Pushbutton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
RS-232 Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
v
VE2812UST / VE2812EUT User Manual
Appendix
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Supported VGA Resolutions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
vi
VE2812UST / VE2812EUT User Manual
About this Manual
This user manual is provided to help you get the most from the VE2812UST /
VE2812EUT unit. It covers all aspects of installation, configuration, and operation. An overview of the information found in the manual is provided below.
Chapter 1, Introduction
introduces you to the HDMI & VGA HDBaseT
Transmitter. Its purpose, features, installation considerations, and panel components are presented and described.
Chapter 2, Hardware Setup
describes the steps that are necessary to quickly
and safely set up your installation.
Chapter 3, Operation
explains the Long Reach Mode and limitations, and how
to set up the input detection mode using the a pushbutton and RS-232 commands.
provides a list of safety instructions and precautions, contact
information for ATEN technical support, product specifications, and other technical information.
Note:
Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit or any connected devices.
ATEN regularly updates its product documentation for new features and fixes. For an up-to-date VE2812UST / VE2812EUT documentation, visit
.........................
http://www.aten.com/global/en/ vii
VE2812UST / VE2812EUT User Manual
Conventions
This manual uses the following conventions:
Monospaced
[ ]
1.
♦
→
Indicates text that you should key in.
Indicates keys you should press. For example, [Enter] means to press the
Enter
key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them:
[Ctrl+Alt].
Numbered lists represent procedures with sequential steps.
Bullet lists provide information, but do not involve sequential steps.
Indicates selecting the option (on a menu or dialog box, for example), that comes next. For example, Start
→
Run means to open the
Start
menu, and then select
Run
.
Indicates critical information.
viii
VE2812UST / VE2812EUT User Manual
Product Information
For information about all ATEN products and how they can help you connect without limits, visit ATEN on the Web or contact an ATEN Authorized Reseller.
Visit ATEN on the Web for a list of locations and telephone numbers:
International
North America http://www.aten.com
http://www.aten-usa.com
ix
VE2812UST / VE2812EUT User Manual
This Page Intentionally Left Blank
x
Chapter 1
Introduction
Overview
ATEN VE2812UST / VE2812EUT is a video transmitter that can send VGA (with audio) and HDMI signals up to 100 m over a single Cat 5e/6/6a or ATEN 2L-
2910 Cat 6 cable. The VE2812UST / VE2812EUT guarantees reliable transmission of HDMI signals, supporting 3D, Deep Color, and embedded HD lossless audio formats. In addition, the VE2812UST / VE2812EUT supports
Long Reach Mode, which allows the device to transmit signals up to 150 m,
1080p, over a Cat 5e/6 cable.
The VE2812UST / VE2812EUT can also function as a video switch by connecting to two sources and outputting them to the same format. The
VE2812UST / VE2812EUT is designed for use in meeting rooms or digital education environments where high video quality is required.
1
VE2812UST / VE2812EUT User Manual
Features
Extends HDMI or VGA signals over a single Cat 5e/6/6a cable
HDMI (3D, Deep Color, 4K); HDCP compatible
Superior video quality
HDMI 4K up to 100 m via a Cat 5e/6/6a cable or ATEN 2L-2910 Cat 6 cable
VGA 1600 x 1200 / 1920 x 1200 up to 100 m via a Cat 5e/6/6a or ATEN
2L-2910 Cat 6 cable
Supports HDBaseT Long Reach Mode – extends signals up to 150 m,
1080p via a single Cat 5e/6 cable
Supports Auto Switch – the VE2812UST / VE2812EUT automatically switches to a newly plugged-in source
Functions as a switch and a converter
A switch: Connects to two source devices (HDMI or VGA)
A converter: Applies to receivers with different interfaces (DVI,
DisplayPort, or HDMI)
Supports RS-232 channel transmission and source switch control
Compatible receivers – VE1812R, VE811R, VE814AR, VE801R, VE802R,
VE601R, VE901R, or future ATEN HDBaseT Receivers
Supports IR signal frequencies from 30 kHz to 60 kHz
Plug-and-play with no required software
Built-in 8KV / 15KV ESD protection
2
Chapter 1. Introduction
Planning the Installation
Requirements
Prepare the following before installing the VE2812UST / VE2812EUT unit:
1 HDMI and/or VGA source device
1 Cat 5e/6/6a or ATEN 2L-2910 Cat 6 cable
Considerations
To ensure video quality, ATEN recommends using a Cat 5e/6/6a cable.
Note:
ATEN recommends using the ATEN 2L-2910 Cat 6 cable for best results.
The maximum transmission distance varies at different parts of the transmission:
Connection
Computer to the VE2812UST
/ VE2812EUT
Interface
HDMI
The VE2812UST /
VE2812EUT to a compatible
ATEN Video Extender
A compatible ATEN Video
Extender to the display
Distance
1.8 m
Cat 5e/6/6a 100 m / 150 m (up to 1080p in Long
Reach Mode)
HDMI 5 m
Compatible ATEN Video Extenders
The VE2812UST / VE2812EUT is compatible with the following ATEN
HDBaseT Video Extenders:
VE1812R
VE811R
VE814AR
VE601R
VE801R/802R
3
VE2812UST / VE2812EUT User Manual
VE901R
Future ATEN HDBaseT receivers
Components
Front View
4
No.
Component
1 IR Port
2 HDMI In
3 Audio In
4 VGA In
5 Input Switch
Pushbutton
Description
Connects to an IR transmitter/receiver.
Connects to the HDMI Out port on the source device.
Connects to the Audio Out port on the source device.
Connects to the VGA Out port on the source device.
Press to switch among the Auto Switch, HDMI, and VGA input mode. The input mode status is indicated by the three
LEDs to the right of this pushbutton. For details, see
Chapter 1. Introduction
Side View 1
No. Component Description
1 Firmware Upgrade Switch This port is reserved for ATEN Technical Support. If you would like to do a firmware upgrade yourself, please contact your dealer.
2 HDBaseT Long Reach
Mode Switch
Put the switch to
ON
to enable the Long Reach
Mode. For more details on Long Reach Mode,
Side View 2
No. Component
1 Power Jack
2 RS-232 Port
3 HDBaseT Output
Description
Connects to the Power Adapter.
Connects to an RS-232 main controller, such as a PC or Control system.
Connects to the HDBaseT Output port on a compatible ATEN video receiver via an RJ-45 cable.
5
VE2812UST / VE2812EUT User Manual
LED Display
You can find the unit’s LEDs on the top and front panel as illustrated below. See the table below for details on LED indication.
6
No. LED
1 Link LED
Indication Description
Lights orange The transmission to the receiver is stable.
Blinks orange The transmission to the receiver is unstable.
Lights green The unit is receiving power.
2 Power LED
3 HDMI Mode LED Lights orange The unit is set to transmit HDMI input.
4 Auto Switch
Mode LED
Lights orange The unit is in the Auto Switch mode. For details, see
5 VGA Mode LED Lights orange The unit is set to transmit VGA input.
Note:
The Power and Link LED blink at the same time to indicate that the firmware upgrade is in progress.
Auto Switch Mode LED, HDMI Mode LED, and VGA Mode LED light and blink at the same time to indicate that the RS-232 mode is changed.
Chapter 2
Hardware Setup
1. Please review the safety information regarding the placement of this device in
2. Do not power on the VE2812UST / VE2812EUT until all the necessary hardware is connected.
Mounting the VE2812UST / VE2812EUT Unit
VE2812UST / VE2812EUT is designed to be installed in a wall or ceiling.
Site Preparation
Choose a location where cables are free of interference and install the cables into the wall before installing the unit.
The unit can be installed into a wall box or simply into a recession in the wall.
Please reserve enough space in the site for the body of the unit.
For more information on the recommended reserved space for each unit, see
Drawing Screw Site
Screw sites are required to secure the unit into the wall. There are regional template screw sites and the unit can use the sites easily.
If you wish to create your own installation sites, the dimensions below will help you decide how to draw them.
Template is available at the end of the document for both models, please refer
7
VE2812UST / VE2812EUT User Manual
VE2812UST Wall Mount
1. Insert the VE2812UST to your installation site and secure it by tightening 4 screws to the screw holes as shown:
Note:
Screws stabilizing the unit to the site are not included in the package content
The installation site can be a wall or ceiling.
2. Attach the faceplate to the VE2812UST and secure the wall plate to the installation site by tightening the 4 screws (provided in the package) to the unit as shown:
8
Chapter 2. Hardware Setup
VE2812EUT Wall Mount
1. Secure the supplied mounting kit to your installation site by tightening 4 screws (EU type) or 2 screws (MK type) to the screw holes as shown:
Note:
Screws stabilizing the mounting kit are not included in the package content.
This installation site can be a wall or ceiling.
2. Insert the unit to the installation site and secure it by tightening the 4 screws
(provided in the package) onto the mounting kit as shown:
9
VE2812UST / VE2812EUT User Manual
Connecting the VE2812UST / VE2812EUT Unit
Follow the steps below to connect the VE2812UST / VE2812EUT to a source, a compatible ATEN Video Extender, and other controls as required.
VE2812UST
Top View Side View
4
1
1
1
5
3
2
VE1812 Receiver
VE2812EUT
4
Side View
5
3
2
VE1812 Receiver
1 1 1
1. Use an HDMI or VGA cable to connect the HDMI or VGA Out port on your source device to the HDMI or VGA In port.
Note:
For a VGA source, make sure to also connect a VGA audio jack to the Audio In port on the VE2812UST / VE2812EUT unit to transmit audio.
2. Connect one end of the RJ-45 cable to the HDBaseT Output port on the
VE2812UST / VE2812EUT, and the other end to the HDBaseT Input port on your video extender receiver.
3. (Optional) Connect your computer or control system to the RS-232 Serial
Port on the VE2812UST / VE2812EUT.
10
Chapter 2. Hardware Setup
Note:
The RS-232 Serial Port is a terminal block connector. Please refer to
4. (Optional) Connect an IR transmitter/receiver to the IR port.
5. Connect power to the unit. Please refer to
Terminal Block Connection
Follow the instructions below for terminal block connection:
1. Detach the terminal block from the port (e.g. RS-232 Serial Port).
2. Loosen the screws on top of the terminal block (turning a screwdriver counter-clockwise) to open the gates.
3. Insert the wires into the gates according to the label on the unit.
4. Tighten the screws for each gate to secure the wires to the terminal block.
5. Attach the terminal block back to its port.
Power Supply Information
Follow the diagram and the steps below to connect the power to the unit.
1
+5V
5mm
GND
2
+5V
GND
(+)
3
(-)
1. Cut the connector end of the power adapter.
2. Strip 5mm (0.5cm) off the insulation cover of the Power Adapter cable to expose two wires: a +5V wire and a GND (grounding) wire.
3. Insert the exposed +5V wire and GND wire tightly into the provided 2-pin
Terminal Block Connector. Refer to
for more details.
Note:
You can determine the exposed wire’s polarity (i.e., +5V or GND) by using a voltmeter.
11
VE2812UST / VE2812EUT User Manual
RS-232 Channel Transmission
You can manage the VE2812UST / VE2812EUT via RS-232 serial devices, such as computers or bar code scanners. The RS-232 signal transmission flow can be illustrated as follows (VE2812UST is used as the example):
The general concept here is that a RS-232 signal can be transmitted (Tx) to the receiving (Rx) end of a unit. The received signal can then be transmitted (Tx) to the receiving (Rx) end of another unit. The RS-232 signals can be transmitted back the other way.
You can set the VE2812UST / VE2812EUT to either bypass serial data or to receive RS-232 commands. By default, the VE2812UST / VE2812EUT is set to bypass serial data. To set the unit to receive RS-232 commands, press the Input
Switch pushbutton for 5 seconds. For details on RS-232 commands, see
12
Chapter 3
Operation
Selecting the Input Mode
Input Modes
You can switch among different input modes based on your needs. Refer to the table below for how each mode works.
Input Mode
Auto Switch
(LED lights orange)
HDMI
(LED lights orange)
VGA
(LED lights orange)
Description
The VE2812UST / VE2812EUT:
automatically transmits the first detected input to the connected receiver.
prioritizes HDMI transmission if both HDMI and
VGA inputs are plugged in at the same time.
automatically switches to a newly detected input to the connected receiver.*
Note:
You can disable this part of the Auto Switch mode (automatic input switching) using an RS-232 command. For more details, see
The VE2812UST / VE2812EUT only transmits HDMI source to the connected receiver.
The VE2812UST / VE2812EUT only transmits VGA source and its audio input to the connected receiver.
13
VE2812UST / VE2812EUT User Manual
Input Selection Pushbutton
Press the Input Switch Pushbutton located on the front panel to switch among the Auto Switch, HDMI, and VGA input mode.
14
Chapter 3. Operation
RS-232 Commands
You can change the input mode using RS-232 commands. Refer to the table below for a list of available tasks and the corresponding commands.
Note:
To switch to RS-232 mode, press the Input Switch pushbutton for 5 seconds. For RS-232 command mode, the Auto Switch Mode LED,
HDMI Mode LED, and VGA Mode LED light orange and blink 3 times.
For RS-232 bypass mode, the Auto Switch Mode LED, HDMI Mode LED, and VGA Mode LED light orange and blink 1 time. The RS-232 status is kept even when the unit is powered on and off. For detailed LEDs behavior, see LED Display, page 6.
Type the corresponding command to execute a task. For example, to enable automatic switching, type
swmode next
and then press
[Enter]
.
Task
Enable automatic input switching
Disable automatic input switching
Set the unit to the HDMI mode
Set the unit to the VGA mode
View the current input mode settings
Control
swmode next
Command
Input
N/A swmode off sw sw read
N/A i i
N/A
Port
N/A
N/A
01
02
N/A
Note:
Press
[Enter]
to execute a command.
The current input mode setting is also indicated by the Auto Switch, HDMI, and
VGA LEDs.
To switch to RS-232 mode, press the Input Switch pushbutton for 5 seconds. For
RS-232 command mode, the Auto Switch Mode LED, HDMI Mode LED, and VGA
Mode LED light orange and blink 3 times. For RS-232 bypass mode, the Auto
Switch Mode LED, HDMI Mode LED, and VGA Mode LED light orange and blink 1 time. The RS-232 status is kept even when the unit is powered on and off. For
15
VE2812UST / VE2812EUT User Manual
Long Reach Mode
Long Reach Mode is a modulation that extends the transmission distance up to
150 m using a Cat 5e/6 cable while compromising the maximum frame rate to
1080p, 24 bpp, 60 Hz via a single Cat 5e/6 cable. To enable Long Reach Mode
,
put the HDBaseT Long Reach Mode Switch to
ON
at either the transmitter or the connected receiver.
Note:
When Long Reach Mode is enabled, the VE2812UST / VE2812EUT will not be able to transmit 4K signals, in which case, the output display will be blank.
16
Appendix
Safety Instructions
General
This product is for indoor use only.
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for adequate ventilation. To ensure reliable operation, and to protect against overheating, these openings must never be blocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as this will block its ventilation openings. Likewise, the device should not be placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
The device is designed for IT power distribution systems with 230V phaseto-phase voltage.
To prevent damage to your installation it is important that all devices are properly grounded.
The device is equipped with a 3-wire grounding type plug. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not attempt to defeat the purpose of the grounding-type plug. Always follow your local/national wiring codes.
Do not allow anything to rest on the power cord or cables. Route the power cord and cables so that they cannot be stepped on or tripped over.
If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the
17
VE2812UST / VE2812EUT User Manual extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.
To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).
Position system cables and power cables carefully; Be sure that nothing rests on any cables.
Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock.
Do not attempt to service the device yourself. Refer all servicing to qualified service personnel.
If the following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need for service.
The device does not operate normally when the operating instructions are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair.
18
Appendix
Technical Support
International
For online technical support – including troubleshooting, documentation, and software updates: http://support.aten.com
North America
Email Support
Online Technical
Support
Telephone Support
Troubleshooting
Documentation
Software Updates [email protected]
http://www.aten-usa.com/support
1-888-999-ATEN ext 4988
1-949-428-1111
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase
Your computer configuration, including operating system, revision level, expansion cards, and software
Any error messages displayed at the time the error occurred
The sequence of operations that led up to the error
Any other information you feel may be of help
19
VE2812UST / VE2812EUT User Manual
Specifications
Function
Video Input
Interfaces
Impedance
Max. Distance
Video Output
Max. Data Rate
Max. Pixel Clock
Compliance
VE2812UST VE2812EUT
1 x HDMI Type A Female (Black)
1 x HDB-15 (VGA) Female (Blue)
HDMI: 100 Ώ
HDB-15 (VGA): 75 Ώ
1.8 m
Max. Resolutions /
Distances
Audio
Input
Control
RS-232 Connectors
Baud Rate
Data Bits
Stop Bits
IR
10.2 Gbps (3.4 Gbps per lane)
340 MHz
HDMI (3D, Deep Color, 4K)
HDCP Compatible
Consumer Electronics Control (CEC)
HDMI:
Up to 4k @70m (Cat 5e/6) / 100m (Cat 6a/ATEN 2L-2910
Cat6)
Up to 1080p @100m (Cat 5e/6/6a)
VGA:
Up to 1920 x 1200 & 1600 x 1200 @70m (Cat 5e/6) /
100m (Cat 6a/ATEN 2L-s910 Cat 6)
Up to 1920 x 1080 @100m (Cat 5e/6/6a)
4k supported:
4096 x 2160 / 3840 x 2160 @60Hz (4:2:0)
4096 x 2160 / 3840 x 2160 @30Hz (4:4:4)
1 x HDMI Type A Female (Black)
1 x Mini Stereo Jack Female (Green)
1 x Terminal Block, 3 Pole
19200
8
1, no parity and flow control
1 x Mini Stereo Jack Female (Black)
20
Appendix
Function
Switches
Video Input Port
Selection
Long Reach Mode
Switch
Firmware Upgrade
Power
Connectors
Consumption
Environmental
Operating Temperature
Storage Temperature
Humidity
Physical Properties
Housing
Weight
Dimensions (L x W x H)
Dimensions (L x W x H)
VE2812UST
1 x Pushbutton - HDMI, VGA, and AUTO
1 Slide Switch - ON/OFF
1 Slide Switch - ON/OFF
1 x Terminal Block, 2 Pole
DC 5V, 3.04W
0 - 40°C
-20 - 60°C
VE2812EUT
DC 5V, 3.14W
0 x 80% RH, Non-Condensing
0.29kg (0.64 lb)
10.42 x 8.79 x 5.19 cm
3
(4.10 x 3.46 x 2.04 in.
3
)
11.43 x 11.43 x 0.60 cm
3
(4.5 x 4.5 x 0.24 in.
3
)
Metal
0.35kg (0.77 lb)
5.00 x 10.80 x 5.17 cm
(1.97 x 4.25 x 2.04 in.
3
3
)
8.60 x 15.10 x 1.35 cm
(3.39 x 5.94 x 0.53 in.
3
3
)
21
VE2812UST
VE2812UST
VE2812(A)EUT
Panel Mount Cutout
Width of faceplate = 15.1 cm [5.94"]
11.1 cm [4.37"]
Cutout
Area
Note:
ATEN recommends a 1-gang wall box with a depth of at least
3.6 cm (1.42 inches) to accommodate the connectors and cables.
VE2812(A)EUT
Appendix
Supported VGA Resolutions
The VE2812UST / VE2812EUT supports the following VGA resolutions:
VGA Resolution
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1152 x 564
1152 x 564
1280 x 600
1280 x 720
1280 x 768
1280 x 800
1280 x 800
1280 x 960
1280 x 1024
1280 x 1024
1360 x 768
1366 x 768
1400 x 1050
1440 x 900
1600 x 900
1600 x 1200
1680 x 1050
1920 x 1080
Frame Rate (Hz)
60
75
60
75
60
75
60
60
75
60
60
75
60
60
60
60
60
60
60
75
60
60
60
60
29
VE2812UST / VE2812EUT User Manual
Limited Warranty
ATEN warrants its hardware in the country of purchase against flaws in materials and workmanship for a Warranty Period of two [2] years (warranty period may vary in certain regions/countries) commencing on the date of original purchase. This warranty period includes the LCD panel of ATEN LCD
KVM switches. Select products are warranted for an additional year (see
A+
Warranty
for further details). Cables and accessories are not covered by the
Standard Warranty.
What is covered by the Limited Hardware Warranty
ATEN will provide a repair service, without charge, during the Warranty Period.
If a product is detective, ATEN will, at its discretion, have the option to (1) repair said product with new or repaired components, or (2) replace the entire product with an identical product or with a similar product which fulfills the same function as the defective product. Replaced products assume the warranty of the original product for the remaining period or a period of 90 days, whichever is longer.
When the products or components are replaced, the replacing articles shall become customer property and the replaced articles shall become the property of ATEN.
To learn more about our warranty policies, please visit our website: http://www.aten.com/global/en/legal/policies/warranty-policy
30
Appendix
Template Printing
Please use 1:1 ratios when printing.
We also recommend using A4 sized paper or larger.
After printing, please measure the print so that the labeled measurement is correct.
31
VE2812UST Screw Sites Template
0.80cm
VE2812EUT Screw Sites Template
1.1cm
6.0cm
Download
Public link updated
The public link to your chat has been updated.
Document public link
Advertisement
Key features
- Extends HDMI or VGA signals over a single Cat 5e/6/6a or ATEN 2L-2910 Cat 6 cable
- Designed to mount in two- gang junction box
- HDMI 1.4 (3D, Deep color, 4K); HDCP 2.2 compliant
- Superior video quality:
- • HDMI: 4K at distance up to 100 m via a Cat 6a or ATEN 2L-2910 Cat 6 cable
- •VGA: 1600 x 1200 and 1920 x 1200 up to 100 m via a Cat 6a or ATEN 2L-2910 Cat 6 cable
- Supports HDBaseT Long Reach Mode – up to 150 m via a single Cat 5e/6 cable at resolutions up to 1080p
- Supports Auto Switch – automatically switches to a newly plugged-in source
- Functions as a switch or a converter
- • A Switch: Connects two sources (HDMI or VGA)