- Computers & electronics
- TVs & monitors
- Wall & ceiling mounts accessories
- MULTIPLEX
- CEV Metal Bonnet
- Installation Guide
advertisement
Part Number 5031540
CEV Metal Bonnet Installation Instructions
CEV30
Parts Included in Kit No.: 5031536
Description
8-32 Self Tapping Countersink Screw
8-32 Self Tapping Screw
No.8 Course Thread Screw
115 Volt 60Hz Wiring Diagram Label
208-230 Volt 60Hz Wiring Diagram Label
220-240 Volt 50Hz Wiring Diagram Label
Key Switch Bracket
Metal Bonnet Assembly
Splash Panel
Condenser Bracket Assembly
Installation Instructions
Beverage Configuration Label (STD)
Beverage Configuration Label (Juice)
Beverage Configuration Label (5 VLV)
Beverage Configuration Label (Var VLV)
Part Number Qty
0900504
5011940
5013485
5029625
5029626
5029627
5031050
5031537
5031538
5031539
5031540
5012519
5013734
5027794
020001226
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 of 4
CEV40
Parts Included in Kit No.: 020002844
Description
8-32 Self Tapping Countersink Screw
8-32 Self Tapping Screw
No.8 Course Thread Screw
115 Volt 60Hz Wiring Diagram Label
208-230 Volt 60Hz Wiring Diagram Label
220-240 Volt 50Hz Wiring Diagram Label
Key Switch Bracket
Metal Bonnet Assembly
Splash Panel
Condenser Bracket Assembly
Installation Instructions
Beverage Configuration Label (STD)
Beverage Configuration Label (Var VLV)
Part Number Qty
0900504
5011940
5013485
5029625
5029626
5029627
5031050
20002778
020002829
5031539
5031540
5013361
020002740
1
1
1
1
1
1
1
1
1
1
1
1
1
Revision-1
1A
1B
2A
2B
3A
3B
1C
CEV Metal Bonnet Installation Instructions
Figure 1
Figure 2
Figure 3
Part Number 5031540
3D
1D
2C
3C
2 of 4
Instructions
1) Disconnect or shut off power supply to
CEV unit. Failure to do so may cause electrical shock or injury .
2) Remove existing plastic merchandiser, light kit, bonnet wrap and rear panel assembly from existing unit. Remove existing condenser air filter from rear panel assembly. Clean air filter thoroughly and retain for reuse. Review service and install manual for further removal details
3) Disconnect wires from valve key switch.
Remove both L-shape brackets on each side of the valve mount cap ( 1A ) by removing the four 8-32 mounting screws
(two each side). Retain screws for reuse.
Remove existing key switch assembly from L-shaped bracket by removing the retaining nut. Retain key switch assembly for reuse. Reinstall two of the four 8-32 mounting screws ( 1B ) in bottom mounting slots on left and right sides of valve mount cap ( See Figure 1 ).
4) Remove drain pan ( 1D ) and the existing splash panel ( 1C ). Keep drain pan for reuse and discard splash panel ( See
Figure 1 ).
5) The new splash panel ( 2A ) will require the correct wiring diagram installed on back upper left side ( 2B ) and plumbing diagram on back upper right side ( 2C ) of panel. All voltage option wiring diagrams are provided along with all plumbing diagrams. Review unit serial tag to determine correct voltage wiring diagram to be applied on new splash panel ( See
Figure 2 ).
Revision-1
5B
5C
6B
6A
4B
CEV Metal Bonnet Installation Instructions
Figure 4
Figure 5
Figure 6
Part Number 5031540
3 of 4
4A
5A
4C
Instructions
6) Install new splash panel ( 1A ) by reinstalling the two 8-32 mounting screws. Reinstall drain pan ( 1D ) and attach any drain lines that were disconnected ( See Figure 1 ).
7) Mount the key switch assembly ( 3A ) to new key switch bracket ( 3B ) as shown.
Mount the key switch and bracket to smaller deck plate ( 3C ) located on top right side of plastic tub. Use the existing hole on smaller deck plate ( 3C ) to mount key switch and bracket with the provided
8-32 self tapping screw ( 3D ). Connect wires previously disconnected to the key switch ( See Figure 3 ).
8) Remove clear film on the adhesive tape located on the back left side ( 4B ) and back right side ( 4C ) of condenser bracket assembly ( 4A ) ( See Figure 4 ).
9) Center condenser bracket assembly ( 5A ) onto air cooled condenser ( 5B ). The bracket should be flush to the bottom side of condenser bracket assembly ( 5A ) to top of air cooled condenser ( 5B ). Press condenser bracket assembly ( 5A ) firmly against air cooled condenser ( 5B ) to adhere adhesive tape. Install the provided
8-32 self tapping countersink screw ( 5C ) through slot in lower left corner of condenser bracket assembly ( 5A ) and into hole in air cooled condenser ( 5B )
( See Figure 5 ).
10) Reinstall the condenser air filter ( 6A ) into the condenser bracket assembly ( 6B ) as shown ( See Figure 6 ).
Revision-1
7B
7C
7D
CEV Metal Bonnet Installation Instructions
Figure 7
4 of 4
7A
Instructions
11) Assemble the metal bonnet assembly
( 7A ) onto CEV unit. The metal bonnet assembly ( 7A ) needs to sit flush on the top cosmetic trim area ( 7B ) of plastic tub and over top of valve mount cap. Align the mounting slots located on front bottom left and right side of metal bonnet assembly ( 7A ) with top mounting slots of valve mount cap. Reinstall the two 8-32 mounting screws ( 7C ) through slots of the metal bonnet assembly and valve mount cap. Install the provided No.8 course thread screw through slot located on top left side ( 7D ) of metal bonnet assembly ( 7A ) and into speed-clip on top of condenser bracket assembly ( See
Figure 7 ).
12) Turn on or reconnect power supply to
CEV unit. Dispense drinks from unit to ensure proper operation before placing unit back into general service.
Part Number 5031540 Revision-1
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project