Toshiba SD-K531SU2 DVD & Blu-ray User Guide

PDF Download

Document

DIGITAL VIDEO

DVD VIDEO PLAYER & VIDEO

CASSETTE RECORDER

SD-K531SU2

OWNER’S MANUAL

Introduction

Connections

Basic setup

Playback

(VCR)

Recording

(VCR)

Other functions

(VCR)

Basic playback

(DVD)

Advanced playback

(DVD)

Function setup

(DVD)

Others

*J2E51001A*

04/11 K Printed in Thailand

This device does not tape-record copy protected DVD Video Discs.

Introduction

IMPORTANT SAFEGUARDS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to rain or moisture.

CAUTION:

TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN

BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

FCC NOTICE

:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Changes or modifications not expressly approved by the partly responsible for compliance with the

FCC Rules could void the user's authority to operate this equipment.

CAUTION:

THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CARE-

FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTE-

NANCE, CONTACT AN AUTHORIZED SERVICE LOCATION.

USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLO-

SURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED.

DO NOT STARE INTO BEAM.

Location of the required Marking

The rating sheet and the safety caution are on the rear of the unit.

CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE

STANDARDS, 21 CFR SUBCHAPTER J.

IMPORTANT SAFEGUARDS

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a soft dry cloth for cleaning the exterior cabinet only.

6. ATTACHMENTS

The manufacturer of this unit does not make any recommendations for attachments, as they may cause hazards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

8. ACCESSORIES

PORTABLE CART WARNING

(symbol provided by RETAC)

Do not place this unit on an unstable cart, stand, tripod, bracket, or table.

The unit may fall, causing serious injury, and serious damage to the unit.

8A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

9. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation,

S3125A to ensure reliable operation of the unit, and to protect it from overheating.

These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and/or the manufacturer’s instructions have been adhered to.

10. POWER SOURCE

This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company.

11. GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

Introduction

IMPORTANT SAFEGUARDS

13. LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the

National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

GROUND CLAMP

ELECTRIC SERVICE

EQUIPMENT

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC-NATIONAL ELECTRICAL CODE

S2898A

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

For example: a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.

e. If the unit has been dropped or the cabinet has been damaged.

f . When the unit exhibits a distinct change in performance, this indicates a need for service.

Introduction

Precautions

Notes on handling

When shipping the DVD/VCR, the original shipping carton and packing materials come in handy. For maximum protection, repack the unit as it was originally packed at the factory.

Do not use volatile liquids, such as insect spray, near the DVD/VCR. Do not leave rubber or plastic products to contact the DVD/VCR for a prolonged period. They will leave marks on the finish.

The top and rear panels of the DVD/VCR may become warm after a long period of use. This is not a malfunction.

When the DVD/VCR is not in use, be sure to remove the disc and the video cassette turn off the power.

If you do not use the DVD/VCR for a long period, the unit may not function properly in the future. Turn on and use the DVD/VCR occasionally.

Notes on moisture condensation

Moisture condensation damages the DVD/VCR.

Please read the following carefully.

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the head drum or the optical pick-up lens inside this unit, one of the most crucial internal parts of the DVD/VCR.

Exam ple of moisture condensation!

Tape

Head drum

Notes on locating

Place the DVD/VCR on a level surface. Do not use it on a shaky or unstable surface such as a wobbling table or inclined stand. The loaded disc or the video tape may become dis-aligned and damage the DVD/

VCR.

When you place this DVD/VCR near a TV, radio, or

VCR, the playback picture may become poor and the sound may be distorted. In this case, place the DVD/

VCR away from the TV, radio, or VCR.

Moisture condensation occurs during the following cases.

When you bring the DVD/VCR directly from a cold place to a warm place.

When you use the DVD/VCR in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit.

In summer, when you use the DVD/VCR in a hot and humid place just after you move the unit from an air conditioned room.

When you use the DVD/VCR in a humid place.

It’s too warm!

Notes on cleaning

Use a soft, dry cloth for cleaning.

Use a dry cloth to wipe.

Do not use any type of solvent, such as thinner and benzine, as they may damage the surface of the

DVD/VCR.

If you use a chemical saturated cloth to clean the unit, follow that product’s instructions.

Do not use the DVD/VCR when moisture condensation may occur.

If you use the DVD/VCR in such a situation, it may damage discs and internal parts. Remove the disc or the video tape, connect the power cord of the DVD/

VCR to the wall outlet, turn on the DVD/VCR, and leave it for two or three hours. After two or three hours, the DVD/VCR will have warmed up and evaporated any moisture. Keep the DVD/VCR connected to the wall outlet and moisture condensation will seldom occur.

Wait!

Wall outlet

IMPORTANT SAFEGUARDS

/ Power source

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

21. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

22. DISC TRAY

Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.

23. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause a product damage. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.

24. LASER BEAM

Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.

25. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.

26. NOTE TO CABLE TV SYSTEM INSTALLER

This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Power source

Wider Hole and Blade

AC Outlet

Polarized AC Cord Plug

(One blade is wider than the other.)

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet.

Notes:

• Never connect the AC line cord plug to other than the specified voltage (120V 60Hz). Use the attached power cord only.

• If the polarized AC cord does not fit into a non-polarized AC outlet, do not attempt to file or cut the blade. It is the user’s responsibility to have an electrician replace the obsolete outlet.

• If you cause a static discharge when touching the unit and the unit fails to function, simply unplug the unit from the AC outlet and plug it back in. The unit should return to normal operation.

Notes on discs

On handling discs

Do not touch the playback side of the disc.

Structure of disc contents

Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs are divided into tracks.

DVD video disc

Title 1

Chapter 1 Chapter 2

DVD video disc

Title 2

Chapter 1 Chapter 2 Chapter 3

Do not attach paper or tape to discs.

Playback side

Video CD/Audio CD

Track 1 Track 2 Track 3 Track 4 Track 5

On cleaning discs

Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.

Each title, chapter or track is assigned a number, which is called “title number”, “chapter number” or “track number” respectively.

There may be discs that do not have these numbers.

Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight or near heat sources.

Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier.

Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

Notes on copyright

It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, and rent copyrighted material without permission.

This device does not tape-record copy protected DVD

Video Discs.

The device is not to be used for copying copyrighted content without the express written permission of the copyright owner.

Obtaining such permission is the sole responsibility of the user.

This product incorporates copyright protection technology that is protected by method claims of certain

U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is prohibited.

Introduction

Notes on discs (continued)

About this owner’s manual

This owner’s manual explains the basic instructions of this DVD/VCR. Some DVD video discs are produced in a manner that allows specific or limited operation during playback. As such, the DVD/VCR may not respond to all operating commands. This is not a defect in the DVD/

VCR. Refer to instruction notes of discs.

“ ” may appear on the TV screen during operation.

A “ ” means that the operation is not permitted by the

DVD/VCR or the disc.

For example, sometimes it is unable to stop the playback of copyright message of the disc when the

STOP ( ) button is pressed. Alternatively, the “ ” may also indicate that the feature is not available for the disc.

Playable discs

This DVD/VCR can play the following discs.

Disc Mark Contents

Disc

Size

Maximum playback time

Approx. 4 hours

(single sided disc)

12 cm

DVD video discs

Audio

Video

(moving pictures)

Approx. 8 hours

(double sided disc)

Approx. 80 minutes

(single sided disc)

8 cm

Approx. 160 minutes

(double sided disc)

Notes on region numbers

The region number of this DVD/VCR is 1. If region numbers, which stand for their playable area, are printed on your DVD video disc and you do not find 1 or ALL , disc playback will not be allowed by the player. (In this case, the DVD/VCR will display a message on-screen.)

Video

CDs

DIGITAL VIDEO

Audio

Video

(moving pictures)

12 cm Approx. 74 minutes

8 cm Approx. 20 minutes

On Video CDs

This DVD/VCR supports Video CDs equipped with the

PBC (Version 2.0) function. (PBC is the abbreviation of

Playback Control.) You can enjoy two playback variations depending on types of discs.

• Video CD not equipped with PBC function

(Version 1.1)

Sound and movie can be played on this DVD/VCR in the same way as an audio CD.

• Video CD equipped with PBC function

(Version 2.0)

In addition to operation of a Video CD not equipped with the PBC function, you can enjoy playback of interactive software with search function by using the menu displayed on the TV screen (Menu Playback).

Some of the functions described in this owner’s manual may not work with some discs.

12 cm Approx. 74 minutes

Audio

CDs

Audio

8 cm

(CD single)

Approx. 20 minutes

The following discs are also available.

DVD-R/RW discs of DVD video format

CD-R/CD-RW discs of CD-DA, Video CD, SVCD,

MP3, WMA or JPEG format

Kodak Picture CD and FUJICOLOR CD format

Some of these discs may be incompatible.

• You cannot play discs other than those listed above.

• You cannot play discs of DVD-RAM, DVD-ROM,

Photo CD, etc., or non standardized discs even if they may be labeled as above.

• Some CD-R/RWs cannot be played back depending on the recording conditions.

• This DVD/VCR uses the NTSC color system, and cannot play DVD video discs recorded in any other color system (PAL, SECAM, etc.).

Because of problems and errors that can occur during the creation of DVD software and/or the manufacture of DVD discs, Toshiba America Consumer Products, L.L.C. and

Toshiba of Canada, Ltd. cannot guarantee that this player will play every feature of every DVD bearing the DVD logo.

As one of the creators of DVD technology, Toshiba DVD players are manufactured to the highest standards of quality and, as a result, such incompatibilities are very rare.

If you happen to experience and difficulty playing a DVD on a Toshiba DVD player, please feel free to call our Contact listed in “How to Obtain Warranty Services” (page 71).

Introduction

Identification of controls

See the page in for details.

Front panel

VCR/DVD mode selector button 22

EJECT button 29

Cassette loading slot 29

DVD indicator

VCR indicator 22

42 OPEN/CLOSE button

Disc tray 42

Introduction

IMPORTANT SAFEGUARDS .......................... 2

Power source ................................................... 5

Precautions ...................................................... 6

Notes on discs .................................................. 7

Contents. .......................................................... 9

Identification of controls ................................. 10

Connections

Antenna connections ...................................... 14

Cable TV connections .................................... 16

Connecting to a TV ........................................ 18

Connecting to optional equipment .................. 20

Basic setup

Setting the video channel ............................... 22

Setting the language ...................................... 23

Clock setting ................................................... 24

Tuner setting .................................................. 27

Basic playback (DVD)

Playing a disc ................................................. 42

Advanced playback (DVD)

MP3/WMA/JPEG playback ............................ 45

Zooming ......................................................... 50

Locating desired scene .................................. 50

Marking desired scenes ................................. 51

Repeat playback ............................................ 52

A-B Repeat playback ..................................... 52

Program playback (CD) .................................. 53

Random playback (CD) .................................. 53

Changing angles ............................................ 54

Title selection ................................................. 54

DVD menu ...................................................... 54

Playback (VCR)

Loading and unloading a cassette tape ......... 29

Cassette tape playback .................................. 30

Special playback ............................................ 31

Convenience function ..................................... 32

Recording (VCR)

Recording a TV program ................................ 34

One-touch Timer Recording (OTR) ................ 36

Timer recording .............................................. 37

Function setup (DVD)

Changing soundtrack language ..................... 55

Setting surround sound .................................. 55

Setting subtitles .............................................. 56

Karaoke playback ........................................... 56

E.B.L. (Enhanced Black Level) ...................... 57

Setting the aspect ratio of TV screen ............. 58

Setting on screen display ............................... 59

Status display of disc ..................................... 59

Dynamic Range Control ................................. 60

Parental control setting .................................. 61

To change the parental level .......................... 62

Temporary disabling of rating level by DVD disc .. 63

Setting OSD language ................................... 64

Setting language ............................................ 65

Selecting PROGRESSIVE scan ..................... 66

Other functions (VCR)

Stereo recording and playback ...................... 39

Second Audio Program (SAP) ........................ 39

Duplicating a video tape ................................. 40

Recording a DVD/CD disc .............................. 41

Others

Language code list ......................................... 67

Troubleshooting ............................................. 68

Specifications ................................................. 69

Limited warranty ............................................. 70

ON/STANDBY button 22

REC button 34

AUDIO (L/R)/VIDEO IN

(LINE IN 2) jacks 40

Remote sensor 13

Display window 11

CHANNEL

buttons 34

STOP button 30

PLAY button 30

FF (Fast Forward) button

REW (Rewind) button 30

Rear panel

DVD COAXIAL DIGITAL

AUDIO OUT jack 20

When connecting the optical digital cable, remove the cap and fit the connector into the jack firmly.

When not using the jack, keep the cap inserted to protect it from dust intrusion.

DVD S-VIDEO

OUT jack 19

DVD OPTICAL DIGITAL AUDIO

OUT jack (dust protection cap) 20

DVD/VCR common AUDIO

(L/R)/VIDEO OUT jacks 18

RF IN jack 14

AC power cord 5

S-VIDEO/COMPONENT

Video selector switch 19

DVD COMPONENT

OUT jacks 19

DVD AUDIO (L/R)

OUT jacks 19

AUDIO (L/R)/VIDEO

IN (LINE IN1) jacks 40

RF OUT jack 14

Display window

Play indicator

VCR indicator (VCR) Still indicator Disc inserted indicator (DVD)

Recording indicator (VCR)

Disc inserted indicator (CD)

AM/PM indicator

(AM is not displayed)

Track indicator (CD)

Tape loaded indicator (VCR)

Multifunctional indicator

Progressive indicator

Timer Recording indicator (VCR)

VCR operation status

Press CALL to display information on screen.

To cancel the display, press CALL again.

While watching TV

DAY OF THE WEEK

CLOCK

STEREO AND

SECOND

AUDIO

PROGRAM

(SAP)

8 : 47AM MON

STEREO SAP

CH 125

00 : 00 : 00 SP

CHANNEL

TAPE SPEED

While operating a tape

HI-FI STEREO

8 : 30AM MON

HI-FI

STEREO 00 : 15 : 12 SP

VCR Icons

Recording :

OPERATING

MODE

AUTO REPEAT

TAPE IN

Rec/Pause :

Play :

Stop :

Eject :

REAL TIME COUNTER OUTPUT SELECTION

DVD/CD/VCD operation status

Each press of DISPLAY, the status display of the disc will appear on the screen and change as follows.

DVD

DISC OPERATION

TITLE NO.

ELAPSED

TIME

00:34:56 01:12:33

TOTAL

TIME

Title

1/8

1/32

1/99

00:34:56 01:12:33

Chapter 1/999

Eng DolbyDigital

1/9

Eng

ANGLE NO.

CHAPTER NO.

A KIND OF AUDIO

AUDIO LANGUAGE

SUBTITLE LANGUAGE

CD/VCD

DISC

OPERATION

TRACK NO.

Track 11/99

34:56 71:33

TOTAL

TIME

ELAPSED TIME

Introduction

Identification of Controls (continued)

The instructions in this manual describe the functions on the remote control. See the page in for details.

Remote control

CALL button 24

DISPLAY button 59

VCR DVD selector button 22

Direct channel selection buttons 28

Number buttons 45

INPUT SELECT button 40

PROGRESSIVE button 66

TV/VCR button 22

COUNTER RESET button

ANGLE button 54

SP/SLP button 34

PLAY MODE button 52

REC button 34

OTR button 36

TIMER REC button 37

PLAY button 30

REW button 30

SLOW button 31

MARKER button 51

ZERO RETURN button 32

JUMP button 50

VCR MENU button 23

SETUP button 47

Direction buttons 45

( / / / )

SET +/- buttons 23

Channel +/– buttons 34

CANCEL button 37

VCR

DVD

CALL

DISPLAY

EJECT

OPEN/CLOSE

INPUT SELECT

PROGRESSIVE

8 9 0

TV/VCR

AUDIO SELECT

AUDIO

ATR

SUBTITLE

COUNTER RESET

ANGLE

SP/SLP

PLAY MODE A-B RPT CLOCK/COUNTER

REC/OTR TIMER REC

–

INDEX

SKIP

INDEX

SKIP

PLAY

REW

SLOW

FWD

STOP

PAUSE/STILL

ZERO RETURN

JUMP MARKER TOP MENU RETURN

VCR MENU

SETUP SET + MENU

CM SKIP

ZOOM

CH + CH –

CANCEL

ENTER

SET –

Power ( ) button 22

EJECT button (VCR) 29

OPEN/CLOSE button (DVD) 42

ATR button 31

SUBTITLE button 56

AUDIO SELECT button

AUDIO button 55

CLOCK/COUNTER button 33

INDEX + button 33

SKIP button 44

A-B RPT button 52

INDEX – button 33

SKIP button 44

FWD button 30

STOP button 30

PAUSE/STILL button 31

TOP MENU button 54

RETURN button 58

CM SKIP button 31

ZOOM button 50

*MENU button 54

ENTER button 23

Inserting batteries

1 Slide the battery compartment cover in the direction of the arrow.

2 Install two “R03/AAA” batteries

(supplied), paying attention to the polarity diagram in the battery compartment.

3 Replace the compartment cover.

Battery precautions

The precautions below should be followed when using batteries in this device:

1. Use only the size and type of batteries specified (R03/AAA).

2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.

3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions.)

6. Dispose of used batteries in a designated area. Do not throw batteries into a fire. Attention should be drawn to the environmental aspects of battery disposal.

Remote control basics

• Press POWER ( ) to turn the DVD VCR on or off.

• Select your desired operating mode (DVD or VCR) using VCR DVD.

(DVD or VCR indicator on the front panel will show you which mode is selected.)

• Press CH + or CH – to move through the channels one channel at a time.

• The CH +/– ( / ) and SET +/– ( / ) are also used to navigate on-screen menu system.

• You can directly access specific channels using Number buttons.

• Each press of VCR DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the

DVD screen (DVD mode).

Operation

• Aim the remote control at the remote sensor and press control buttons to operate.

• Operate the remote control within 30

angle on either side of the remote sensor, up to a distance of Approx. 7 meters.

Approx. 7 meters

* MENU button

Use the MENU button to display the menu included on many DVD video discs. To operate a menu, follow the instructions in “DVD Menu.” 54

Connections

Antenna connections

If you are using an antenna system, follow these instructions. If you are a Cable TV subscriber, skip ahead to page 16 for the proper connections.

Antenna to DVD/VCR connection

The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV and connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.

1 Combination VHF/UHF Antenna with 75 ohm Coaxial Cable

DVD/VCR

75 ohm Coaxial Cable

(ANT)

OUT

(TV)

2 Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire

DVD/VCR

Matching Transformer 300 ohm Input 75 ohm output (not supplied)

(ANT)

OUT

(TV)

300 ohm Twin Lead (Flat) Wire

(not supplied)

Separate VHF and UHF Antennas

DVD/VCR 3

VHF

UHF

Combiner 75/300 ohm Inputs 75 ohm output

(not supplied)

300 ohm Twin Lead (Flat) Wire

(not supplied)

(ANT)

OUT

(TV)

Note:

75 ohm Coaxial Cable

If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and one 75 ohm output.

Notes: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to the DVD/VCR properly.

• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor type antenna is required.

• If you are not sure about the connection, please refer to qualified service personnel.

DVD/VCR to TV connection

After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.

Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the connection diagram.

This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.

75 ohm Coaxial Cable (supplied)

VHF/UHF IN

Note: If a VHF or UHF antenna is used, set the TV/CABLE menu option to the “TV” mode.

TV with single 75 ohm VHF/UHF antenna input

75 ohm Coaxial Cable

(supplied)

Splitter 75 ohm Input

75/300 ohm outputs

(not supplied)

75 ohm Coaxial Cable

(supplied)

Splitter 75 ohm Input

300 ohm outputs

(not supplied)

UHF

VHF

Note: If a VHF or UHF antenna is used, set the TV/CABLE menu option to the “TV” mode.

TV with 300 ohm UHF and 75 ohm VHF antenna inputs

UHF

VHF

Note: If a VHF or UHF antenna is used, set the TV/CABLE menu option to the “TV” mode.

TV with 300 ohm UHF and 300 ohm VHF antenna inputs

Connections

Cable TV connections

Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This

DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company supplied converter box, except for those premium channels which are intentionally scrambled. If you subscribe to a premium channel which is scrambled, you must have a descrambler box for proper reception.

DVD/VCR

VHF/UHF

IN (ANT) Incoming Cable

(ANT)

OUT

(TV)

Allows: * Recording of nonscrambled channels.

* Use of the programmable timer.

* Recording of one channel while watching another.

DVD/VCR

Converter/

Descrambler

Incoming

Cable

(ANT)

OUT

(TV)

Allows: * Recording of channels through the converter box

(scrambled and unscrambled).

* Using the programmable timer to record only the channel selected at the converter box.

Prevents: * Recording one channel while watching another.

* Using the DVD/VCR tuner to select channels.

VHF/UHF

IN (ANT)

Note:

To record from converter/descrambler,

DVD/VCR tuner must be tuned to the converter output channel, usually channel 3 or 4.

DVD/VCR 3

Incoming Cable

(ANT)

OUT

(TV)

Converter/Descrambler

VHF/UHF

IN (ANT)

Allows: * Recording of nonscrambled channels.

* Use of the programmable timer.

* Recording an unscrambled channel while watching any channel selected at the converter box.

Prevents: Recording scrambled channels.

Note:

If you are playing a tape or using the tuner built into the DVD/VCR, the converter must be set to the video channel output of the

DVD/VCR (either 3 or 4).

Note: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output of the Converter/Descrambler box, usually channel 3 or 4.

Connections

Connecting to a TV

Connect the DVD/VCR to your TV.

Note: This method transports VHS and DVD-video signals. For enhanced DVD-video performance, we recommend you

also connect the S-video or ColorStream ® component video outputs to your TV/monitor. (See page 19.)

Connecting to a TV

Signal flow

To wall outlet

(yellow) (red) (white)

To ANALOG AUDIO OUT

To VIDEO

OUT

Audio/video cable (supplied)

To audio inputs

To video input

(yellow)

(red) (white)

TV or monitor with audio/video inputs

Notes:

• Refer to the owner’s manual of the connected TV as well.

• When you connect the DVD/VCR to your TV, be sure to turn off the power and unplug both units from the wall outlet before making any connections.

• If your television set has one audio input, connect the left and right audio outputs of the DVD/VCR to a Y cable adapter (not supplied) and then connect to your TV.

• Connect the DVD/VCR directly to your TV. If you connect the DVD/VCR to a VCR, TV/VCR combination or video selector, the playback picture may be distorted as DVD video discs are copy protected.

IMPORTANT: Make sure the TV/CABLE menu option is set to the “CABLE” mode.

This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult your local cable company for more information concerning connection to their descrambler equipment. There are many ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.

DVD/VCR

Splitter

A/B Switch

VHF/UHF

IN (ANT)

Incoming Cable

Converter/Descrambler

(ANT)

OUT

(TV)

Allows: * Recording of one channel while watching another.

* Using the programmable timer to record only the channel selected at the converter box.

* Recording of all channels through the converter box.

Prevents: * Watching scrambled channels while recording another channel.

* Using the DVD/VCR tuner to select channels.

DVD/VCR 5

Splitter

Incoming Cable

Converter/Descrambler

(ANT)

OUT

(TV)

A/B Switch

VHF/UHF

IN (ANT)

Allows: * Recording of nonscrambled channels.

* Recording of one channel while watching another.

* Watching premium channels through the converter while recording nonscrambled channels.

* Using the programmable timer.

Prevents: Recording scrambled channels.

DVD/VCR

Splitter

Converter/Descrambler

Incoming Cable

Converter/Descrambler

(ANT)

OUT

(TV)

VHF/UHF

IN (ANT)

A/B Switch

Allows: * Recording of all channels through the converter box.

* Recording a scrambled or unscrambled channel while watching another (scrambled or unscrambled) channel.

* Using the programmable timer to record only the channel selected at the converter box.

Prevents: Using the DVD/VCR tuner to select channels.

S-video output

An S-Video connection is superior to Video (Yellow) output. Use this method for DVD playback when the connected television has S-

Video input, and does not have component video inputs.

Component video outputs

PROGRESSIVE outputs

Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video signal. Connecting to these inputs allows you to view the highest quality pictures with less flicker.

INTERLACED outputs

Some TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy the highest quality

DVD picture playback.

Notes:

• Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)

• In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such a case, adjust the TV or monitor for optimum performance.

Connecting to an audio system and TV equipped with S-video input/component video inputs

Note: The S-video output and component video output transports the DVD-video signal exclusively and will deliver enhanced DVD video picture performance.

Signal flow

(white)

To ANALOG

AUDIO OUT

(red)

To wall outlet

To S-

VIDEO

OUT

To P

VIDEO

OUT

To P

VIDEO

OUT

To Y

VIDEO

OUT

When you make this connection, set the S-VIDEO/

COMPONENT Video selector switch to the desired position.

And also you must select the corresponding video input on your TV.

Component video cable (not supplied)

Audio cable (not supplied)

To audio inputs of the amplifier

To Y video input

(red)

To P B/ C B video input

To P R/ C R video input

To S-video input

S-video cable (not supplied)

If you connect the DVD/VCR to your TV with the DVD OUT jacks, select the corresponding video input on your television to watch DVD video discs.

TV or monitor with

ColorStream ® component video inputs

(white)

Audio system

Notes:

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.

• If you place the DVD/VCR near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD/

VCR away from the tuner and radio.

• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the speakers may be damaged.

• When connecting to a TV using the Video or S-video jack, make sure that the Progressive indicator “ ” on the display window is not lit. If it is lit, the Video and S-video outputs do not feed the correct signals and you cannot see any picture. To turn off the Progressive indicator, select PROGRESSIVE scan Off (see page 66).

Connections

Connecting to optional equipment

You can enjoy high quality dynamic sounds of DVD video discs or audio CDs by connecting the DVD/VCR to optional audio equipment.

For connection to your TV, see “Connecting to a TV”

18 19

• This selection uses the following reference mark.

: Front speaker

: Rear speaker

: Sub woofer

: Center speaker

: Signal flow

Connecting to an amplifier equipped with a Dolby Digital decoder

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs encoded via the Dolby Digital recording system with this dynamic realistic sound by connecting the DVD/VCR to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark.

Amplifier equipped with a

Dolby Digital decoder

Manufactured under license from

Dolby Laboratories. “Dolby” “Pro

Logic” and the double-D symbol are trademarks of Dolby Laboratories.

• Use DVD video discs encoded via the Dolby Digital recording system.

To COAXIAL type digital audio input

To OPTICAL type digital audio input

Optical digital cable

Ω

coaxial cable

Connect either.

Connecting to an amplifier equipped with Dolby Surround Pro Logic

Dolby Surround Pro Logic

You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left front speakers, a center speaker, and one or two rear speakers).

With an amplifier equipped with Dolby Digital

Connect the equipment the same way as described in “Connecting to an amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.

With an amplifier not equipped with Dolby Digital

Connect the equipment as follows.

• This connection is only suitable for Video CDs and

Audio CDs.

Amplifier equipped with

Dolby Surround Pro Logic

* Connect one or two rear speakers.

The output sound from the rear speakers will be monaural even if you connect two rear speakers.

To audio input

Audio cable

To ANALOG

AUDIO OUT

Connecting to an amplifier equipped with a DTS decoder

Digital Theater Systems (DTS)

DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs.

If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS encoded sound tracks on DVD video discs or audio CDs.

Amplifier equipped with a

DTS decoder

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems,

Inc.

• Use DVD video discs or audio

CDs encoded via the DTS recording system.

To COAXIAL type digital audio input

To OPTICAL type digital audio input

Optical digital cable

75 Ω coaxial cable

Connect either.

Basic setup

Setting the video channel

When a TV is connected with the 75 ohm coaxial cable only.

To view playback of a recorded tape or DVD disc, or to watch a program selected by the VCR's channel selector, the TV must be set to channel 3 or 4 (video channel).

POWER

TV/VCR

VCR DVD

Setting the video channel

1 Press and hold 3 or 4 on the remote for 3 seconds in standby mode.

The video channel will start to flash for 3 seconds in the display window.

2 Press POWER to turn on the DVD/VCR.

For a push-button TV tuner

If CH 3 or 4 corresponding to the video channel cannot be tuned on your TV, proceed as follows: set the VCR

3/4 channel selector and the TV to CH 3 or 4, play back a prerecorded tape and tune the TV to receive a sharp color picture from the video cassette recorder.

Refer to your TV owner's manual for details.

Note:

If the unit does not operate properly, or No key operation

(by the unit and/or the remote control): Static electricity, etc., may affect the player's operation. Disconnect the AC power cord once, then connect it again.

3 Press VCR DVD selector to select the VCR mode.

VCR

DVD

The VCR indicator on the front panel will light.

4 Turn ON the TV and set to CH 3 or 4 to correspond with the channel selected in step 1.

5 Press TV/VCR to select the VCR position.

TV/VCR

The VCR indicator will appear in the display window.

6 Select any channel to receive a TV station in your area.

The channel number will appear on the screen for about 4 seconds.

Warning

When playing DTS-encoded discs (audio CDs), excessive noise may be output from the analog stereo jacks. To avoid possible damage to the audio system, you should take proper precautions when the ANALOG AUDIO OUT (L/R) jacks of the

DVD/VCR are connected to an amplification system. (Do not leave the ANALOG AUDIO OUT (L/R) wires dangling.) To enjoy

DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the

BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR.

Connecting to an amplifier equipped with an MPEG2 audio decoder

MPEG2 sound

You can enjoy motion picture and live concert DVD video discs encorded via the MPEG2 recording system with dynamic realistic sound by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio processor.

Amplifier equipped with an

MPEG2 audio decoder

• Use DVD video discs encoded via the MPEG2 recording system.

To COAXIAL type digital audio input

To OPTICAL type digital audio input

Optical digital cable

Ω

coaxial cable

Connect either.

Connecting to an amplifier equipped with a digital audio input

2 channel digital stereo

You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speaker system (right and left front speakers).

Amplifier equipped with a digital audio input

To COAXIAL type digital audio input

To OPTICAL type digital audio input

Optical digital cable

Ω

coaxial cable

Connect either.

Notes:

• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the AC-3 RF input of a Dolby Digital Receiver.

This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the BITSTREAM/PCM AUDIO

OUT jack of the DVD/VCR.

• Connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the “OPTICAL” or “COAXIAL” input of a Receiver or

Processor.

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.

• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers and your hearing may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the speakers may be damaged.

Setting the language

You can choose from three different languages (English,

French and Spanish) for the on-screen displays.

VCR DVD

1,4

1–3

Setting the language

Preparation:

• Turn ON the TV and select to the corresponding video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

1 Press VCR MENU.

The VCR menu screen will appear.

VCR MENU

SETUP

Press SET + or – to select “SYSTEM

SETUP”, then press ENTER.

If you use the unit for the first time and press VCR MENU, instead of the main menu screen the “SYSTEM SETUP” menu screen in step 2 may appear.

SET +

CH –

ENTER

SET –

CH +

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

OFF

4 Press VCR MENU until the MENU screen is cleared.

VCR MENU

SETUP

Notes:

• Both the VCR and the DVD have their own player menus 57 .

• If no buttons are pressed for more than 60 seconds, the VCR

MENU screen will return to normal TV-operation automatically.

⟨

+/-/ENTER/MENU

⟩

2 Press SET + or – to select “LANGUAGE”, then press ENTER.

SET +

CH –

ENTER

SET –

CH +

SYSTEM SETUP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

ON OFF

ON OFF AUTO CLOCK

STANDARD TIME

DAYLIGHT SAVING TIME

⟨ +/-/ENTER/MENU ⟩

3 Press SET + or – to select the desired language:

English (ENGLISH), Spanish (ESPAÑOL) or

French (FRANCAIS), then press ENTER.

SET +

CH –

ENTER

SET –

CH +

LANGUAGE/IDIOMA/LANGUE

ENGLISH

ESPAÑOL

FRANCAIS

⟨

+/-/ENTER/MENU

⟩

Basic setup

Clock setting

The AUTO CLOCK function will automatically set the built-in clock

(Month, Day, Year and Time) when the DVD/VCR is connected to an

Antenna or Cable system and it is turned off. The DVD/VCR searches for a station in your area containing the necessary AUTO CLOCK setting signals. Once received, it will take approximately 4 minutes for the clock to set itself automatically.

AUTO CLOCK setting

Preparation:

• Turn ON the TV and select the corresponding video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

1 Connect the Antenna or Cable system.

• If you use a cable box, turn it on.

2 Plug the AC Power cord to the AC outlet.

3 Make sure the DVD/VCR is turned off.

• If you press POWER, the Auto Clock

set is not programmed.

4 Wait at least three minutes and press

POWER.

1,5

2,4

2,3

To set AUTO CLOCK to off

When shipped from factory the AUTO CLOCK is set to “ON”.

But if you do not want AUTO CLOCK setting:

1 Press VCR MENU.

VCR MENU

SETUP

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

OFF

+/–/ENTER/MENU

CALL

POWER

VCR DVD

Press SET + or – to select “SYSTEM SETUP”, then press ENTER.

CH –

SET +

ENTER

SET –

CH +

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

+/–/ENTER/MENU

OFF

5 Press CALL to check the clock setting on the on screen display.

CALL

DISPLAY 8 : 47 AM MON

STEREO SAP

CH 125

3 Press SET + or – to select “AUTO CLOCK”.

CH –

SET +

ENTER

SET –

CH +

SYSTEM SETUP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

OFF

AUTO CLOCK

STANDARD TIME

DAYLIGHT SAVING TIME

+/–/ENTER/MENU

00 : 00 : 00 SP

6 If the clock is not set, check the antenna condition. The AUTO CLOCK may not function properly if the reception condition is not good.

4 Press ENTER to select “OFF”.

CH –

SET +

ENTER

SET –

CH +

SYSTEM SETUP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

OFF

AUTO CLOCK

STANDARD TIME

DAYLIGHT SAVING TIME

+/–/ENTER/MENU

AUTO CLOCK adjustment

The auto clock adjustment will be updated at 6:00

AM, 12:00 PM and 6:00 PM everyday when the

DVD/VCR turned off.

• If you use a cable box and you want AUTO CLOCK adjustment to be performed, the cable box must be left on.

• The AUTO CLOCK adjustment is not effective when there is a difference of more than 5 minutes exists between the built-in clock time and the actual time.

5 Press VCR MENU repeatedly to return to the normal screen.

VCR MENU

SETUP

• When the AUTO CLOCK is set to

“OFF”, the AUTO CLOCK adjustment does not function.

• Set the clock manually 26 .

Basic setup

Clock setting (continued)

If the AUTO CLOCK process did not set the date and time correctly, you must set them manually for timer recording and DAYLIGHT

SAVING TIME.

2–4

CANCEL

2–4

Manual clock setting

EXAMPLE: Setting the clock to “8:30 AM” September,

24 (FRI), 2004.

1 Press VCR MENU.

VCR MENU

SETUP

6 After setting the clock, date and time starts functioning automatically.

8 : 30 AM FRI

2 Press SET + or – to select “SYSTEM SETUP”, then press ENTER.

CH –

SET +

CH +

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

OFF

ENTER

SET –

+/–/ENTER/MENU

3 Press SET + or – to select “CLOCK SET”, then press ENTER.

CH –

SET +

ENTER

SET –

CH +

SYSTEM SETUP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

AUTO CLOCK

STANDARD TIME

OFF

DAYLIGHT SAVING TIME

⟨

+/-/ENTER/MENU

⟩

4 Press SET + or – to set the month, then press

ENTER.

CH –

SET +

ENTER

SET –

CH +

MONTH

DAY

YEAR

1 (WED)

2004

TIME 12 : 00 AM

⟨

+/–/ENTER/CANCEL/MENU

⟩

To make corrections any time during the process

Press CANCEL repeatedly until the item you want to change blinks, then press SET + or –.

Note:

After a power failure or disconnection of the power, the timer settings will be lost. In this case, reset the present time.

5 Set the day, year and time as in step 4.

MONTH

DAY

24 (FRI)

YEAR 2004

TIME 8 : 30

⟨

+/–/ENTER/CANCEL/MENU

⟩

To set STANDARD TIME To set DAYLIGHT SAVING TIME

In the rare event that you live within broadcast range of two stations in two different time zones, the DVD/VCR may recognize the wrong station for the AUTO CLOCK setting.

To correct the situation:

1 Press VCR MENU.

VCR MENU

SETUP

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

OFF

+/–/ENTER/MENU

You can set the DAYLIGHT SAVING TIME automatically or manually.

1 Press VCR MENU.

Press SET + or – to select “SYSTEM SETUP”, then press ENTER.

VCR MENU

SETUP

SET +

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

OFF

CH – CH +

ENTER

SET –

+/–/ENTER/MENU

2 Press SET + or – to select “SYSTEM SETUP”, then press ENTER.

SET +

CH –

ENTER

SET –

CH +

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

+/–/ENTER/MENU

OFF

2 Press SET + or – to select “DAYLIGHT

SAVING TIME”, then press ENTER.

CH –

SET +

ENTER

SET –

CH +

SYSTEM SETUP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

OFF

AUTO CLOCK

STANDARD TIME

DAYLIGHT SAVING TIME

+/–/ENTER/MENU

3 Press SET + or – to select “STANDARD TIME”, then press ENTER.

SET +

CH –

ENTER

SET –

CH +

SYSTEM SETUP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

AUTO CLOCK

STANDARD TIME

OFF

DAYLIGHT SAVING TIME

⟨

+/-/ENTER/MENU

⟩

3 Press SET + or – to select one of the options, then press ENTER. Press VCR

MENU until the MENU screen is cleared.

CH –

Press SET + or – to select your time zone, then press ENTER.

SET +

ENTER

SET –

CH +

ATLANTIC : GMT–4hours

EASTERN : GMT–5hours

CENTRAL : GMT–6hours

MOUNTAIN : GMT–7hours

PACIFIC : GMT–8hours

ALASKA : GMT–9hours

HAWAII

AUTO

: GMT–10hours

: AUTO SET

(GMT: Greenwich Mean Time)

CH –

VCR MENU

SETUP

SET +

ENTER

SET –

CH +

ON:

OFF:

AUTO: for manual setting

(forward one hour) for manual setting

(back one hour) for automatic setting

(read XDS in the signal)

When you want to set the DAYLIGHT

SAVING TIME manually, on the first

Sunday in April you set to “ON”, and on the last Sunday in October you set to “OFF”.

5 Press VCR MENU twice to return to the normal screen.

VCR MENU

SETUP

DAYLIGHT SAVING TIME

OFF

AUTO

⟨

+/-/ENTER/MENU

⟩

Notes:

• To be able to select the standard time, the clock must first be set by AUTO CLOCK once.

• If you live in Newfoundland and the AUTO CLOCK does not function properly, set the AUTO CLOCK menu option to “OFF” and set the clock manually.

Notes:

• When shipped from factory, the DAYLIGHT SAVING TIME is set to “AUTO” position.

• When the clock is not set, DAYLIGHT SAVING TIME setting is not available.

• When there is no DAYLIGHT SAVING TIME in your area, always select “OFF” position in step 3.

Tuner setting

This DVD/VCR is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the DVD/VCR’s memory. In addition to normal

VHF and UHF channels, this DVD/VCR can receive up to 113 Cable

TV channels. To use this DVD/VCR with an antenna, set the TV/CABLE menu option to the TV mode. When shipped from the factory, this menu option is in the CABLE mode.

TV/CABLE selection

VCR DVD

1,4

1,3

1,2

Setting channels automatically

Preparation:

• Turn ON the TV and select to the corresponding video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

1 Press VCR MENU. Press SET + or – to select

“CH SETUP”, then press ENTER.

VCR MENU

SETUP

SET +

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

OFF

CH – CH +

ENTER

SET –

+/–/ENTER/MENU

2 Press SET + or – to select “TV/CABLE”.

SET +

CH SETUP

CH – CH +

TV CABLE

AUTO CH MEMORY

ADD/DELETE

ENTER

SET –

+/–/ENTER/MENU

3 Press ENTER to select the TV or CABLE mode.

SET +

The arrow indicates the selected mode.

CH – CH +

ENTER

SET –

CH SETUP

TV CABLE

AUTO CH MEMORY

ADD/DELETE

TV - VHF/UHF channels

CABLE - Cable TV channels

+/–/ENTER/MENU

4 Press VCR MENU until the menu screen is cleared.

VCR MENU

SETUP

1 Repeat left step 1 and press SET + or – to select “AUTO CH MEMORY”.

SET +

CH – CH +

CH SETUP

TV CABLE

AUTO CH MEMORY

ADD/DELETE ENTER

SET –

⟨

+/-/ENTER/MENU

⟩

2 Press ENTER.

Auto tuning will begin. The channel display will count up and when finished, the screen returns to normal.

SET +

CH –

ENTER

SET –

CH +

CH 002

Note:

You can’t select “CH SETUP” if you set the channel to “L1” or

“L2”.

Basic setup

Tuner setting (continued)

NUMBER BUTTONS

To ADD/DELETE channels

1 Repeat the step 1 on page 27. Then press SET + or – to select the “ADD/DELETE” and press

ENTER.

SET +

CH SETUP

TV CABLE

AUTO CH MEMORY

ADD/DELETE

CH – CH +

ENTER

SET –

+/–/ENTER/MENU

2 To Add or Delete desired channels

Press Number buttons or SET + or – to select a channel number you want to add or delete.

2 To add channels

Press ENTER until “ADD” appears on the screen.

To delete channels

Press ENTER until “DELETE” appears on the screen. The channel number will blink.

SET +

9 0

CH –

ENTER

SET –

CH +

ADD CH 003

+/–/0–9/ENTER/MENU

1,2

Noise elimination

When you don't want to receive a weak signal broadcast, a

Blue back screen can be obtained by selecting the NO NOISE

BACKGROUND “ON”. When the unit is shipped from the factory, the NO NOISE BACKGROUND is set to “ON”.

1 Repeat the steps 1~2 on page 26 and press

SET + or – to select “NO NOISE

BACKGROUND”.

CH –

SET +

ENTER

SET –

CH +

SYSTEM SETUP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

ON OFF

AUTO CLOCK

STANDARD TIME

ON OFF

DAYLIGHT SAVING TIME

⟨

+/-/ENTER/MENU

⟩

2 Press ENTER to select “ON” or “OFF” position.

CH –

SET +

ENTER

SET –

CH +

SYSTEM SETUP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

AUTO CLOCK

STANDARD TIME

OFF

DAYLIGHT SAVING TIME

⟨

+/-/ENTER/MENU

⟩

3 Press VCR MENU until the menu screen is cleared.

VCR MENU

SETUP

3 Press VCR MENU until the menu screen is cleared.

VCR MENU

SETUP

Playback (VCR)

Loading and unloading a cassette tape

Use only video cassette tapes marked and .

EJECT

Loading

Push the center of the tape until it is automatically inserted.

Insert the cassette tape with its labeled side facing up and the erase prevention tab positioned at your left. An inverted cassette tape cannot be inserted.

Erase prevention tab

Automatic power ON

When you insert a cassette tape the DVD/VCR power will turn ON automatically.

Automatic playback

When loading a cassette tape without an erase prevention tab, playback will start automatically.

Unloading

1 Press EJECT on the front panel or on the Remote.

2 Remove the cassette tape.

Automatic tape eject

This DVD/VCR will automatically rewind the tape when the tape has ended. Once the tape is rewound to its beginning, the cassette tape will be ejected automatically.

To prevent accidental erasure

To prevent accidental erasure

Remove the erase prevention tab with a screwdriver.

Screwdriver

To record again

Cover the hole with a piece of adhesive tape.

Erase prevention tab

Tape speed and maximum recording time

Tape Speed

SP (Standard Play)

SLP (Super Long Play)

T-160

2-2/3 hours

8 hours

Adhesive tape

T-120

2 hours

6 hours

Video cassette tape

T-90

1-1/2 hours

4-1/2 hours

T-60

1 hour

3 hours

T-30

30 minutes

1-1/2 hours

29 28

Playback (VCR)

Cassette tape playback

To play a prerecorded tape.

VCR DVD

REW

PLAY

FWD

STOP

Playback

Preparation:

• Turn ON the TV and select the corresponding video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light).

1 Load a prerecorded tape

(When loading a cassette tape without the erase prevention tab, playback will start automatically).

Rewind or forward the tape

Stop the playback or recording via STOP on remote.

To rewind the tape:

Press REW.

REW

2 To start playback

Press PLAY.

Playback will start. “ ” will appear on the screen for about 4 seconds.

PLAY

To forward the tape:

Press FWD.

FWD

To stop playback

Press STOP once.

The tape will stop but remain fully loaded and ready to play.

“ ” will appear on the screen for about 4 seconds.

STOP

To discontinue the tape-winding, press STOP. To switch to playback directly (without STOP), press PLAY.

Forward/Reverse picture search mode

When the tape is being winded, you can switch to picture search mode (see next page). To do this, press REW or

FWD and hold it down. The unit will resume the tape advance or rewinding as soon as the button is released.

Notes:

• This VCR selects the playback tape speed SP, LP or SLP automatically.

• The Cassette tape and DVD disc can be played back simultaneously. If you press VCR DVD selector, the tape playback and DVD playback alternate with each other on the screen

(via CH3, 4 or video connection).

Special playback

Picture search

Reverse picture search function

Press REW once or twice during playback.

Forward picture search function

Press FWD once or twice during playback.

To return to playback, press PLAY.

SPEED SEARCH TIMES

TAPE SPEED

SP (Standard Play)

LP (Long Play)

SLP (Super Long Play)

PICTURE SEARCH SPEED

PRESS ONCE PRESS TWICE

3 X

7 X

5 X

9 X

9 X 15 X

SLOW

ATR

REW

PLAY

FWD

PAUSE/STILL

CM SKIP

SET +/–

Adjusting tracking condition

Automatic tracking adjustment

Whenever you insert a tape and start playback, the automatic tracking feature continuously analyzes the signal to enable optimum picture quality during playback.

Manual tracking adjustment

If automatic tracking cannot eliminate noises well during playback, press SET +/– to eliminate the noise. “MANUAL

TR.” will appear on the screen. Press it briefly for a fine adjustment, or press and hold for a coarse adjustment.

Press ATR to reactivate automatic tracking again.

“AUTO TR.” will appear on the screen.

Still picture

Press PAUSE/STILL during playback.

To resume normal playback, press PLAY or PAUSE/STILL.

Slow motion

During playback press SLOW.

To return to playback, press PLAY or SLOW.

Slow tracking and vertical lock adjustment

If noise bars appear in the picture during slow motion, press the SET + /– to reduce the noise bars.

If the still picture jitters excessively, press SET +/– to stabilize the still picture.

Frame by frame picture

Press PAUSE/STILL during playback.

Press SLOW repeatedly: The picture advances frame by frame.

To return to playback, press PLAY or PAUSE/STILL.

CM skip

Press CM SKIP during playback. The DVD/VCR will search forward through approximately 30 seconds of the tape (e.g.

unwanted commercial time) for each press of CM SKIP

(maximum six presses) and then resume normal playback.

For example : 1 press: 30 seconds of tape

2 press: 60 seconds of tape

3 press: 90 seconds of tape

AUTO TR.

Notes:

• The audio output is muted during SPEED SEARCH, STILL,

FRAME ADVANCE and SLOW MOTION.

• During picture search mode there will be noise bars. This is not a defect.

• Playback will commence after approx. 5 minutes to protect the video tape against excessive wear during pause mode.

Video head cleaning

Video head clogging

The video heads are the means by which the DVD/VCR reads the picture from the tape during playback. In the unlikely event that the heads become dirty enough to be clogged, no picture will be displayed. This can easily be determined if, during playback of a known good tape, there is good sound, but no picture (picture is extremely snowy). If this is the case, have the

DVD/VCR checked and cleaned by qualified service personnel.

Good Picture

Snowy Picture

Notes:

• DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR

SERVICE THE UNIT BY REMOVING THE REAR COVER.

• Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.

• To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.

Playback (VCR)

Convenience function

CALL

COUNTER RESET

CLOCK/COUNTER

VCR MENU

PLAY

STOP

ZERO RETURN

ENTER

SET +/–

Zero return function

This function rewinds the tape to the “00:00:00” counter position automatically.

Repeat playback

The entire video tape will play until its end. The tape will automatically rewind to the beginning and the playback will be repeated.

1 Press VCR MENU.

Press SET + or – to select “AUTO

REPEAT”.

VCR MENU

SETUP

CH –

SET +

CH +

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

OFF

ENTER

SET –

+/–/ENTER/MENU

Press CLOCK/COUNTER.

CLOCK/COUNTER

The counter display shows the tape running time during playback or recording.

CH –

Press ENTER to select “ON” or “OFF”.

SET +

ENTER

SET –

CH +

If “ON” is selected, the playback will be repeated endlessly.

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

OFF

+/–/ENTER/MENU

2 Press COUNTER RESET at the desired tape position.

The counter display will be reset to

“00:00:00” position (e.g. the beginning of recording).

COUNTER RESET

ANGLE

3 Press VCR MENU until the menu screen is cleared.

If you press CALL, “ ” will

appear on the screen 11 .

3 Press STOP when playback or recording is completed.

Press ZERO RETURN.

STOP

The tape will automatically rewind or fast forward to the “00:00:00” counter position.

4 To commence playback, press PLAY.

The playback will be repeated

endlessly.

PLAY

ZERO RETURN

JUMP

To cancel repeat mode:

Follow the above step 1, then press ENTER to select

“OFF” position. Press VCR MENU to return to the TV.

Recording (VCR)

Recording a TV program

Recording and viewing the same TV program.

VCR DVD

Recording a TV program

Preparation:

• Turn ON the TV and select to the corresponding video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

1 Load a cassette tape with the erase prevention tab intact.

The DVD/VCR will automatically turn on.

4 Press Number buttons or CH +/– to select the channel to be recorded.

SET + CH 110

9 0

CH –

ENTER

SET –

CH +

2 Press SP/SLP to select the desired tape speed

SP or SLP.

SP/SLP

PLAY MODE

The tape counter and “SP” or “SLP” will appear on the screen for about 4 seconds.

00 : 00 : 00 SP

Select “TV” or “CABLE” to the appropriate position 27 .

TV - VHF/UHF channels

CABLE - Cable TV channels

TV mode direct channel selection:

All channels can be instantly selected by using two buttons. (for example, to select channel 2, press “0”, then

“2”. If you press only “2”, channel selection will be delayed for two seconds.) For channels 10 and above, press the 2 digits in order.

CABLE mode direct channel selection:

1-9 Press 0 twice and then 1-9 as required.

10-12

Example: To select “2”, Press 002.

Press 0 first and then the remaining 2 digits in order from left to right.

13-99

Example: Press 012 for “12”.

Press 2 digits in order.

Example: Press 22 for “22”.

100-125 Press the 3 digits in order.

Example: Press 110 for “110”.

VHF/UHF/CABLE TV CHANNELS

VHF

2-13

UHF

14-69

CABLE TV

VHF

2-13

STD/HRC/IRC

14-36 (A) (W)

37-59 (AA) (WW)

60-85 (AAA) (ZZZ)

86-94 (86) (94)

95-99 (A-5) (A-1)

100-125 (100)(125)

01 (5A)

5 Press REC/OTR.

“ ” will appear on the screen

for about 4 seconds and “REC” will

appear on the display window.

REC/OTR

CH 110

INDEX

VCR DVD

CLOCK/COUNTER

INDEX +/–

STOP

Clock/counter display

Press CLOCK/COUNTER. The clock and tape counter alternate with each other in the display window.

COUNTER

CLOCK/COUNTER

Video index search system

This function enables you to locate the beginning of any recording made on the VCR.

Recording an INDEX mark

The Index Search function automatically records an INDEX mark on the tape whenever a recording is initiated.

INDEX

CH 001

Press VCR DVD selector. The DVD mode and the

VCR mode alternate with each other in the display.

VCR

DVD

CLOCK

DVD mode

Index search

Press INDEX + or – during stop or play mode.

For Succeeding programs: Press INDEX +.

For Preceding programs: Press INDEX –.

(As many as 9 index points can be accessed via this method.)

When the INDEX + or – is pressed, the unit starts searching the INDEX

NO. selected and finds the portion, then playback starts automatically.

To stop the Index Search, press

STOP.

–

INDEX

SKIP

INDEX

SKIP

STOP

+3 or is displayed

INDEX NO. (up to 9)

VCR mode

Notes:

• If you rewind the tape beyond “00:00:00”, a minus sign (“–”) will be displayed in front of the time.

• When you load a tape, the counter will reset to “00:00:00”.

• The counter does not function on nonrecorded (blank) sections of the tape. When you rewind, fast forward or play tapes through blank sections, the counter stops.

Notes:

• When you record an INDEX mark at the very beginning of the tape, the mark may not be found.

• During INDEX search, the tape may stop and begin to play at a slightly different location.

• INDEX may not function properly with old or worn out video tapes.

• INDEX marks may not be found if it is extremely close to the point where the search began.

• In recording, if you stop recording temporarily, the INDEX mark is not recorded on the tape.

SQPB (S-VHS Quasi Playback)

You can playback video cassette tapes recorded in the

S-VHS system.

However, the picture will not have the high resolution of

S-VHS system.

Note: You cannot record S-VHS video format with this VCR.

TV/VCR

PAUSE/STILL

STOP

To stop recording

Press STOP to stop recording.

“ ” will appear on screen for about

4 seconds.

STOP

Auto Rewind feature

This VCR will automatically rewind the tape when the tape has ended (except during OTR and timer recording). It will also eject the tape.

To stop recording temporarily

Press PAUSE/STILL to avoid recording unwanted material. Press again to continue the recording.

“ ” will appear on screen for

about 4 seconds.

PAUSE/STILL

Notes:

• The pause function will be released after 5 minutes to prevent damage to the tape or the VCR. The VCR will change to the

STOP mode.

• You can select a recording channel in the recording pause mode.

Recording one program while watching another

While the VCR is recording, select your desired channel on the TV.

When a TV is connected with an antenna cable only, press TV/VCR to select the TV position.

The “VCR” display will go off and recording will continue.

Select the TV channel you want to watch by using the

TV channel selector.

Note:

Some Cable TV hookups do not permit viewing one channel while recording another. See pages 16 and 17 .

Recording (VCR)

One-touch Timer Recording (OTR)

The One-touch Timer Recording feature provides a simple and convenient way to make a timed recording.

VCR DVD

STOP

One-touch Timer Recording (OTR)

Preparation:

• Turn ON the TV and select to the corresponding video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

Example: One-touch Timer Recording for 30 minutes.

1 Load a cassette tape with the erase prevention tab intact.

The VCR will automatically turn on.

2 Press SP/SLP to select the desired tape speed

SP or SLP.

The tape counter and “SP” or “SLP” will appear on the screen for about 4 seconds.

SP/SLP

PLAY MODE

4 Press Number button or CH +/– to select the channel to be recorded.

CH 110

9 0

SET +

CH –

ENTER

SET –

CH +

5 Press REC/OTR. Recording begins. Press the button again to stop recording after 30 minutes.

Each additional press of REC/OTR will increase recording time as shown in the chart below, up to a maximum of 6 hours.

The OTR and recording time will appear on the screen for about 4 seconds. And, “ ” will appear on the display.

Press once twice

3 times

4 times

5 times

Recording time Press

NORMAL REC 6 times

0:30

1:00

1:30

2:00

Recording time

3:00

7 times

8 times

9 times

10 times

4:00

5:00

6:00

NORMAL REC

OTR 0 : 30

CH 110

REC/OTR

00 : 00 : 00 SP

INDEX

3 Set “TV” or “CABLE” option to the appropriate position 27 .

TV - VHF/UHF channels

CABLE - Cable TV channels

To cancel OTR

Press STOP or turn off the power.

STOP

“ ” will appear on screen for about 4 seconds.

Note:

If you wish to watch the DVD playback during OTR or standard recording, press VCR DVD selector to change to DVD mode and perform the DVD playback 42 .

Recording (VCR)

Timer recording (continued)

VCR DVD

SET +/–

TIMER REC

VCR MENU

ENTER

CANCEL

To confirm or cancel a program

Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g. MO-

SA: Monday to Saturday) Timer recording

Follow the procedure of timer recording on the previous page. At step 3 press SET + or – repeatedly until the desired setting appears. Then press ENTER.

When you press SET – repeatedly, the

DATE indicator will change as follows, in this case the day is Friday.

The current day (Friday) SU-SA (Sunday to Saturday)

1 If the Timer has been activated, press TIMER

REC to deactivate the Timer.

The timer symbol ( ) will disappear. Then press VCR DVD selector to change to VCR mode.

VCR

DVD TIMER REC

One month later minus one day

WKL-WE

(Weekly Wednesday)

SET +

CH – CH +

ENTER

SET –

MO-SA (Monday to Saturday)

MO-FR (Monday to Friday)

WKL-TH (Weekly Thursday)

DATE

WKL-WE

START END CH

CH –

To confirm Timer program:

At step 1 on the previous page select “TIMER REC

SET” and press ENTER.

The timer program list will appear on the screen.

SET +

ENTER

SET –

CH +

DATE

26(SU)

START END CH

11:00PM 11:30PM125SLP

⟨

+/–/ENTER/CANCEL/MENU

⟩

⟨

+/–/ENTER/CANCEL/MENU

⟩

If the programs overlap another

3 To cancel Timer program:

Press SET + or – to select the unwanted program, then press CANCEL to cancel the program.

Do not overlap timer programs as portions of the conflicting programs will be lost. The first recording time has priority over the next recording time as shown in the diagram below.

8 : 00 9 : 00 10 : 00 11 : 00

Program 1

CH –

SET +

ENTER

SET –

CH +

CANCEL

DATE

– – – – – –

START END

– : – –

– – –

– – – – – – – : – – – : – – – – –

⟨

+/–/ENTER/CANCEL/MENU

⟩

– – –

–

Program 2

Program 3

Recording

Control Settings

Prog.1

Deleted Parts

Non Recorded Portion Parts

Prog.2

Prog.3

4 Press VCR MENU repeatedly until the menu screen is cleared.

VCR MENU

SETUP

Notes:

• The daily/weekly recording can be made continuously until the recording is canceled or the tape reaches the end.

• During timer recording the automatic rewinding mechanism does not function.

Notes:

• If there are other timer record programs remaining, TIMER

REC must be pressed to reactivate the timer, otherwise the remaining timer record programs will be ignored.

• You cannot confirm the Timer program during timer recording operation.

• You can correct or cancel a programmed setting in program confirm mode.

Timer recording

Timer recording can be programmed on-screen with the remote control.

The built-in timer allows automatic unattended recording of up to 8 programs within 1 month.

VCR DVD

EJECT

2,3

TIMER REC

1,5

1–3

CANCEL

Timer recording

Preparation:

• Press VCR DVD selector to select the VCR mode.

• Load a cassette tape with the erase prevention tab intact.

• Check the time and date are correct 24 .

Example: Program a timer recording for the 26th day, channel 125 (Cable TV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: SLP).

1 Press VCR MENU. Select “TIMER REC SET”, then press ENTER.

VCR MENU

SETUP

CH –

SET +

ENTER

CH +

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

OFF

SET –

+/–/ENTER/MENU

5 To enter other programs, repeat step 2 through 4.

VCR MENU

SETUP

• To return to the normal screen, press VCR MENU twice.

DATE START END CH

26(SU)

– – – – – –

11:00PM 11:30PM125 SLP

– – – – – – – : – –

– : – –

– – – – – – – : – –

– : – –

– – –

–

⟨

+/–/ENTER/CANCEL/MENU

⟩

2 Press SET + or – to select one of the program line, then press ENTER.

CH –

SET +

ENTER

SET –

CH +

DATE START END

– – – – – – – : – –

– : – –

⟨

+/–/ENTER/CANCEL/MENU

⟩

– – –

– – – –

–

6 Press TIMER REC. The timer symbol ( ) will appear on the display and the VCR stands by for recording.

TIMER REC At the same time, VCR mode will change to DVD mode automatically.

You can use DVD even if the VCR is in the timer recording mode.

If you do not use the DVD, turn the power off.

Notes:

• The timer recording will start at 5 seconds before the time you predetermined.

• If the timer symbol( ) does not appear on the display in spite of the pressing of TIMER REC, the cassette may not have been loaded.

• If the cassette is ejected in spite of the pressing of TIMER

REC, the erase prevention tab of the cassette may have been removed.

3 Press SET + or – to select the date, then press

ENTER.

CH –

SET +

ENTER

SET –

CH +

DATE

26(SU)

– – – – – –

START END

– : – –

– – –

⟨

+/–/ENTER/CANCEL/MENU

⟩

–

4 Set the start time, end time, channel and tape speed as in step 3.

DATE START END CH

26(SU)

– – – – – –

11:00PM 11:30PM125 SLP

– – – – – – – : – –

– : – –

– – – – – – – : – –

– : – –

– – –

–

⟨

+/–/ENTER/CANCEL/MENU

⟩

Notes:

• Press CANCEL to move cursor backward for correction.

• To record from external source set the channel to “L1” or

“L2”.

Notes:

• If the timer symbol ( ) blinks when the timer recording ended, the TV program has not been completely recorded because of an insufficient tape length. Press TIMER REC to cancel the timer program or press EJECT to remove the cassette tape.

• During timer recording standby mode, the VCR mode cannot be operated. To use the VCR, press TIMER REC at first, then press

VCR DVD selector to change to VCR mode. After you use the

VCR, press TIMER REC again to put the VCR into timer recording standby mode.

• If you press TIMER REC during timer recording, the recording operation will be interrupted. If you press TIMER REC again within the programmed time, the recording operation will start again.

• After a power failure or disconnection of the power plug, all programmed recording settings and time display will be lost upon resumption of power. In this case, reset the clock 24 and reprogram any timer recording.

Other functions (VCR)

Stereo recording and playback /

Second Audio Program (SAP)

AUDIO SELECT

SET +/–

VCR MENU

ENTER

Stereo recording and playback

The VHS Hi-Fi audio system permits high fidelity recording of MTS STEREO TV broadcasts.

When a MTS STEREO broadcast is received, “STEREO” will appear on the screen for about 4 seconds and the program can be viewed or recorded in stereo.

The Hi-Fi stereo recording procedure is the same as for normal recordings.

STEREO

Note:

When using a Cable TV system, stereo TV programs may be transmitted over a mono cable channel. In this case

“STEREO” will not appear and the sound will be in mono.

AUDIO SELECT

AUDIO

Second Audio Program (SAP)

Your DVD/VCR is fitted with a SAP broadcast system which enables you to switch to a second audio program when viewing a selected channel.

This function applies only when the program is broadcast in multi-languages through the SAP broadcast system.

1 Press VCR MENU. Then press SET + or – to select “SAP”.

VCR MENU

SETUP

CH –

SET +

ENTER

CH +

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

OFF

SET –

+/–/ENTER/MENU

Output selection

When viewing an MTS stereo TV program, or playing a prerecorded VHS Hi-Fi stereo videotape, press AUDIO

SELECT to select how the audio will be heard through the speakers. Normally set to the Hi-Fi stereo position, this button can be set to the MONO position if the stereo broadcast or videotape audio is of poor quality. The “R” and “L” positions allow the audio from the Right or Left Hi-

Fi channel to be heard over both TV speakers. This button has no effect when viewing a MONO videotape or

TV program. Each time when you press the button,

OUTPUT SELECTION display appears on the screen for several seconds. Refer to the chart below.

OUTPUT

SELECTION

STEREO

L ch

R ch

MONO

SOUND HEARD ON BOTH

SPEAKERS

STEREO

LEFT CHANNEL AUDIO

RIGHT CHANNEL AUDIO

MONO

2 Press ENTER to select “ON”.

Then press VCR MENU until the menu screen is cleared.

SET +

CH –

ENTER

SET –

CH +

VCR MENU

SETUP

TIMER REC SET

AUTO REPEAT

SAP

CH SETUP

SYSTEM SETUP

OFF

+/–/ENTER/MENU

Listening to SAP

When the VCR is turned on or a channel selection is made, make certain the letters “SAP” appears on the screen for about 4 seconds. This means that the “Second

Audio Program” broadcasting is available.

STEREO SAP SAP

OR

Notes:

• When playing back a tape that is not recorded in Hi-Fi stereo mode, the audio will automatically be monaural.

• When listening to a VHS Hi-Fi video tape or MTS broadcast through the VHF/UHF jack (Audio/Video cable not connected), the sound will be monaural.

Other functions (VCR)

Duplicating a video tape

If you connect the DVD/VCR to another VCR or Camcorder, you can duplicate

a previously recorded tape. Make all connections before turning on the power.

VCR DVD

Duplicating a video tape

Preparation:

• Turn ON the TV and select the corresponding video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

• Load a cassette tape with the erase prevention tab intact.

• Load a previously recorded tape into the playback

VCR or Camcorder.

1 Press SP/SLP to select the desired tape speed

SP or SLP.

SP/SLP

PLAY MODE

It is recommended that you set the

tape speed to the SP mode on the

recording VCR for best results.

2 Press INPUT SELECT once or twice to select

AUDIO/VIDEO input position.

“L1” or “L2” will appear in the display.

INPUT SELECT

PROGESSIVE

Connection with second VCR

Playback VCR

To VIDEO OUT To AUDIO (R) OUT

To AUDIO (L) OUT

AUDIO/VIDEO cable (supplied)

Recording VCR

To VIDEO IN To AUDIO (R) IN

To AUDIO (L) IN

L1: on the rear panel

L2: on the front panel

3 Press PLAY on the playback VCR or Camcorder.

Connection with Camcorder

Playback Camcorder

To AV Jack

4 Press REC/OTR on the recording VCR.

The duplicating process begins.

REC/OTR

Recording VCR

5 Press STOP after duplicating a video tape.

STOP

To VIDEO IN

To AUDIO (R) IN

To AUDIO (L) IN

AUDIO/VIDEO cable (not supplied)

For duplicating a previously recorded tape from a camcorder, follow the camcorder manufacturer’s instructions. A typical camcorder dubbing hookup is shown above.

Basic playback (DVD)

Playing a disc

This section shows you the basics on how to play a disc.

CAUTION

Keep your fingers well clear of the disc tray as it is closing.

Neglecting to do so may cause serious personal injury.

4 3, 5

Display window

2

STOP PLAY

1

DVD

VCD

Basic playback

Preparations:

• When you want to view a disc, turn on the TV and select the corresponding video input connected to the DVD/VCR. This may include S-video or component video inputs which are exclusive to DVD playback.

• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected to the DVD/VCR.

Press ON/STANDBY (I / ).

ON/STANDBY The DVD/VCR turns on.

Press VCR/DVD SELECT to select the DVD mode.

VCR/DVD The DVD indicator will light.

Press OPEN/CLOSE or PLAY on the unit.

OPEN/CLOSE

PLAY

The disc tray closes automatically.

On the TV-screen, “ ” changes to

“Reading” and then playback commences.

• A menu screen will appear on the TV screen, if the disc has a menu feature.

Reading

SELECT

3 Press OPEN/CLOSE.

OPEN/CLOSE The disc tray opens.

6 Press / or / to select title.

SET +

CH – CH +

ENTER

SET –

4 Place the disc on the disc tray.

With the playback side down

7 Press ENTER.

SET +

• Title is selected and play commences.

CH – CH +

ENTER

SET –

• There are two different disc sizes. Place the disc in the correct guide on the disc tray. If the disc is out of the guide, it may damage the disc and cause the DVD/VCR to malfunction.

• Do not place a disc which is unplayable in this

DVD/VCR.

8 Press STOP to end playback.

STOP • The unit records the stopped point, depending on the disc. “ ” appears on the screen. Press

PLAY to resume playback (from the scene point).

• If you press STOP again or unload the disc (“ ” appears on the screen.), the unit will clear the stopped point.

To start playback in the stop mode

Press PLAY.

PLAY

Recording a DVD/CD disc

You can record disc material in DVD, Audio CD, etc. onto a Video tape with this DVD/VCR.

Duplicating a DVD or CD disc

Preparation:

• Turn ON the TV and select the corresponding video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

• Load a cassette tape with the erase prevention tab intact.

• Load a DVD/CD disc.

1 Press SP/SLP to select the desired tape speed

SP or SLP.

SP/SLP

PLAY MODE

Notes:

• You may not be able to record the beginning of the disc.

Begin VCR recording once program playback commences on the DVD.

• When the scanning mode is set to the progressive mode, you cannot duplicate a disc material onto a video tape.

When REC/OTR is pressed, the PROGRESSIVE indicator

“ ” on the display window will flash and “Please Set

Off” will appear on the screen.

• You cannot record discs encoded with copy guard function. The following icon and text will show up on the

TV screen.

00 : 00 : 00 SP DISC IS COPY PROTECTED

2 Press VCR DVD selector to select the DVD mode.

The DVD indicator will light.

VCR

DVD

3 Press PLAY to start playback.

PLAY

4 Press REC/OTR to start recording.

REC/OTR

The DVD/VCR will change to the

VCR mode automatically and the playback picture or sound will be duplicated on the video cassette tape.

5 Press STOP if you finish recording.

STOP

If you wish to stop a DVD/CD disc, press VCR DVD selector to change the DVD mode, then press STOP.

VCR DVD

OPEN/CLOSE

PLAY

PAUSE/STILL

STOP

ENTER

To obtain a higher quality picture

Occasionally, some picture noise not usually visible during a normal broadcast may appear on the TV screen while playing a DVD video disc because the high resolution pictures on these discs include a lot of information. While the amount of noise depends on the TV you use with this DVD/VCR, you should generally reduce the sharpness adjustment on your TV when viewing DVD video discs.

About

The icons on the heading bar show the playable discs for the function described under that heading.

: You can use this function with DVD video discs.

: You can use this function with Video CDs.

: You can use this function with Audio CDs and CD-R/RW CDs.

To pause playback (still mode)

Press PAUSE/STILL during playback.

PAUSE/STILL

To resume normal playback, press the PLAY button.

• The sound is muted during still mode.

To stop playback

Press STOP.

STOP

To remove the disc

Press OPEN/CLOSE.

OPEN/CLOSE

Remove the disc after the disc tray opens completely.

Playing a Disc while the VCR section is recording or standing by for timer recording

1) Start to record.

Follow steps 1~5 on page 34.

• If the DVD/VCR is standing by for recording, turn on the DVD/VCR.

2) Press VCR DVD selector to select DVD mode. The

DVD indicator will light.

3) Play a disc.

Follow steps 3 ~ 5 on page 42.

• Press PLAY if the DVD/VCR does not start to play a disc automatically.

4) Stop to play.

Press STOP to stop play back a disc.

Screen saver function

The screen saver operates when you leave the unit in

DVD stop mode for about five minutes.

The screen will repeatedly get dark gradually and back to normal.

To turn off the PBC

Press number button 1 in the stop mode, then press

ENTER.

Be sure to press the OPEN/CLOSE button to close the disc tray after you remove the disc.

Notes:

• If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen according to the type of loaded disc. In this case, check your disc again (See pages 8 and 61).

• Some discs may take a minute or so to start playback.

• When you set a single-faced disc label downwards (ie. the wrong way up) and press the OPEN/CLOSE button or the PLAY button on the unit, “Reading” will appear on the display for 30 seconds and then “Incorrect Disc” will continue to be displayed.

• Some discs may not work the resuming facility.

• Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC, see above.

• Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according to the disc contents the software producers designed, some playback features may not be available. Also refer to the instructions supplied with the DVDs.

• Do not move the DVD/VCR during playback. Doing so may damage the disc.

• Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may cause the DVD/VCR to malfunction.

• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD/VCR to malfunction.

• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the

ON/STANDBY (I / ) button on your remote control once the movie is completed.

• There may be a slight delay between you pressing the button and the function activating.

Basic playback (DVD)

Playing a disc (continued)

You can play discs at various speeds.

REW

SKIP /

PLAY

FWD

PAUSE/STILL

SLOW

DVD

VCD

Playing in fast reverse or fast forward directions

Press REW or FWD during playback.

To resume normal playback

Press PLAY.

PLAY

REW FWD

REW: Fast reverse playback

FWD: Fast forward playback

Each time you press the REW or

FWD button, the playback speed changes.

Notes:

• The DVD/VCR mutes sound and subtitles during reverse and forward scan of DVD video discs. However, the DVD/

VCR plays sound during fast forward or fast reverse play of audio CDs.

• The playback speed may differ depending on the disc.

DVD

VCD

Playing frame by frame

Press PAUSE/STILL during still playback.

PAUSE/STILL

Each time you press the PAUSE/

STILL button, the picture advances one frame.

To resume normal playback

Press PLAY.

PLAY

Note:

The sound is muted during frame by frame playback.

DVD

VCD

Playing in slow-motion

Press SLOW during playback.

SLOW Each time you press the SLOW button, the slow-motion speed changes.

To resume normal playback

Press PLAY.

PLAY

Note:

The sound is muted during slow-motion playback.

DVD

VCD

Locating a chapter or track

Press SKIP or repeatedly to display the chapter or track number you want.

Playback starts from the selected chapter or track.

INDEX

SKIP

+ To locate succeeding chapters or tracks.

–

INDEX

SKIP

Playback starts from the beginning of the current chapter or track.

When you press twice in quick successions, playback starts from the beginning of the preceding chapter or track.

Notes:

• A “Prohibition” symbol may appear at the upper left of the screen. This symbol means either the feature you tried is not available on the disc, or the DVD/VCR cannot access the feature at this time. This does not indicate a problem with the DVD/

VCR.

• The unit is capable of holding a still video image or On screen display image on your television screen indefinitely. If you leave the still video image or On screen display image displayed on your TV for an extended period of time, you risk permanent damage to your television screen. Projection televisions are very susceptible.

Advanced playback (DVD)

MP3/WMA/JPEG playback (continued)

You can select your desired JPEG file on the file menu and picture menu.

The selected JPEG file is automatically adjusted to the TV screen. (When the aspect ratio of the JPEG file is different to your TV screen, the black bar will appear at the top and bottom, or the both sides of the TV screen.

OPEN/CLOSE

0–9

SKIP /

PLAY

STOP

TOP MENU

ENTER

▲ / ▼ / /

JPEG CD playback

1 Press OPEN/CLOSE.

OPEN/CLOSE

The disc tray will open.

Place a disc on which

JPEG files have been recorded onto the tray.

5 Press ENTER.

The selected picture appears on the TV screen.

SET +

CH – CH +

ENTER

SET –

Press OPEN/CLOSE or PLAY.

OPEN/CLOSE

PLAY

The disc tray closes automatically.

On the TV-screen, “Reading” will appear.

Reading will take as much time as the number of file.

Reading

6 Press STOP to end playback.

STOP

The file menu appears on the TV screen.

If you want to watch the other file, repeat steps 4~5.

3 A file menu screen will appear on the TV screen.

Press or to select folder.

CD-R

Collection

Pic-1

Pic-2

Pic-3

Pic-4

-/36

Pic-8

Pic-9

Pic-10

Pic-11

Pic-5

Pic-6

Pic-12

Pic-13

Pic-7 Pic-14

/0-9/Enter/Play Mode/Menu

4 Press / or the desired file.

CH –

SET +

ENTER

SET –

CH +

or Number keys to select

9 0

CD-R

Collection

Pic-1

Pic-2

Pic-3

Pic-4

Pic-5

Pic-6

Pic-7

-/36

Pic-8

Pic-9

Pic-10

Pic-11 11

Pic-12

Pic-13

Pic-14

/0-9/Enter/Play Mode/Menu

To display a picture menu, press MENU.

(To return to a file menu, press TOP MENU.)

Press / or / to select the desired file.

MENU

TOP MENU

• To display next list, press SKIP or .

• When PLAY has been pressed after displaying the file menu, or when the disc tray has been closed after pressing PLAY in step 2, playback begins automatically starting from the first file. In this case, if the first file is a JPEG file, the first JPEG file is played back. If the first file is an MP3/WMA file, only MP3/WMA files are played back in order.

Notes:

• The picture menu is displayed when the FUJICOLOR CD or the Kodak Picture CD are played. To display the file menu press TOP MENU.

• During MP3/WMA/JPEG-Playback, you can not use SEARCH,

A-B Repeat functions.

• You can use Repeat (Track or All), Random functions and

Program playback for MP3/WMA/JPEG CD Playback. (See pages 52 and 53.)

• In the case of a CD containing a mixture of MP3, WMA and

JPEG files, the files are played back by selecting them from the file menu.

File menu information

Operation

Media type

Elapsed time

File number

Folder

CD-R

Pops

1/94 02:36

Japan

Bay Bridge

CLOSE MY EYES

DIVE TO BLUE

Honey

BLUE EYES

Blurry Eyes

14 flower

Lies and Truth-

Pic-1

Pic-2

Pic-3

Pic-4

Pic-5

/0-9/Enter/Play Mode/Menu

: Indicates MP3 file

: Indicates WMA file

: Indicates JPEG file

Microsoft, Windows Media, and Windows Logo are trademarks or registered trademarks of Microsoft

Corporation in both the United States and other countries.

Advanced playback (DVD)

MP3/WMA/JPEG playback

This player can play back the MP3/WMA/JPEG-data which has been recorded on CD-R or CD-RW. To produce the MP3/WMA/JPEG-data, you need a

Windows-PC with CD-ROM drive and a MP3/WMA/JPEG-encoding Software

(not supplied).

The Apple-HFS-System cannot be played.

OPEN/CLOSE

0–9

PLAY

STOP

ENTER

▲ / ▼ / /

MP3/WMA playback

Press OPEN/CLOSE.

OPEN/CLOSE

The disc tray will open.

Place a disc on which MP3 or WMA files have been recorded onto the tray.

5 Press STOP to end playback.

PLAY

STOP

• The unit records the stopped point.

“ ” appears on the screen. Press

PLAY to resume playback (from the scene point).

• If you press STOP again or unload the disc, the unit will clear the stopped point.

Press OPEN/CLOSE or PLAY.

OPEN/CLOSE

The disc tray closes automatically.

CH –

PLAY

On the TV-screen,“Reading” will appear.

Reading will take as much time as the number of file.

Reading

A file menu screen will appear on the TV screen.

Press or to select folder.

SET +

ENTER

SET –

CH +

CD-R -/72 --:--

Pops

Japan

Bay Bridge

CLOSE MY EYES

DIVE TO BLUE

Honey

BLUE EYES

Blurry Eyes

10 flower

Lies and Truthwinter fall

Rain

Strawberry

Welcome party

Thailand

/0-9/Enter/Play Mode

Press / or / or Number keys to select the desired file, then press ENTER.

The file is selected and play commences.

CH –

SET +

ENTER

SET –

CH +

• In case the folder includes more than

15 tracks, press or to display next file list.

CD-R -/72 --:--

Pops

Japan

Bay Bridge

CLOSE MY EYES

10 flower

Lies and Truthwinter fall

DIVE TO BLUE

Honey

BLUE EYES

Blurry Eyes

Rain

Strawberry

Welcome party

Thailand

/0-9/Enter/Play Mode

CD-R

Pops

Mother

Hold Your Last

-/72 --:--

/0-9/Enter/Play Mode

• When PLAY has been pressed after displaying the file menu, or when the disc tray has been closed after pressing

PLAY in step 2, playback begins automatically starting from the first file.

In this case, if the first file is an MP3/

WMA file, only MP3/WMA files are played back in order.

If the first file is a JPEG file, the first

JPEG file is played back.

MP3/WMA/JPEG CD Information

Limitations on MP3/WMA/JPEG CD playback

• MP3/WMA/JPEG CD is the disc that is standardized by

ISO9660, its file name must include 3-digits extension letters, “mp3”, ”wma”, “jpg”.

• The directory and file names of the MP3/WMA/JPEG CD must be correspond to the ISO standardized files.

• This unit can read 200 files per disc. If a disc has more than

200 files, it reads up to 200 files, the remaining files will be omitted.

• The unit is able to recognize up to a maximum of 50 directories per disc.

• MP3/WMA CDs cannot be used for playback for the purpose of recording.

• If the CD has both audio tracks and MP3/WMA/JPEG files, only audio tracks are played.

• It may take more than one minute for this unit to read MP3/

WMA/JPEG files depending on its structure.

• Music recorded by “Joliet Recording Specification” can be played back, the file name is displayed (within 16 letters) on the screen. Long file names will be condensed.

• The music files recorded by “Hierarchical File System”

(HFS) cannot be played.

• The unit can play back baseline and progressive JPEG files.

Limitations on display

• The maximum number for display is 16 letters. Available letters for display are the following: capital or small alphabets of A through Z, numbers of 0 through 9, and _

(under score).

• Other letters than those above are replaced in hyphen.

Notes on MP3/WMA/JPEG files

To play back MP3/WMA/JPEG CD in the recorded order,

1. Use MP3/WMA/JPEG software that records data alphabetically or numerically.

2. Name each file including two-digit or three-digit number

(e.g. “01” “02” or “001” “002”).

3. Refrain from making too many sub-folders.

WMA disc compatibility with this player is limited as follows:

1) Sampling Frequency: within 32 -- 48 kHz

2) Bit Rate: within 48 -- 192kbps.

Mono WMA files and WMA files (under 48kbps) cannot be played back on this player.

Notes:

• Some MP3/WMA/JPEG CDs cannot be played back depending on the recording conditions.

• The CD-R/RW that has no music data or non-MP3/WMA/

JPEG files cannot be played back.

SETUP

ENTER

▲ / ▼ / /

Setting the JPEG Interval

You can continuously play back all JPEG files automatically.

After the setting below, start playing the disc on which JPEG files have been recorded.

Press SETUP in the stop mode. Press select “Picture”, then press ENTER.

VCR MENU

SETUP

Language Picture Sound

Parental Other

4 To make SETUP screen disappear, press SETUP.

VCR MENU

SETUP

SET +

CH –

ENTER

SET –

CH +

/Enter/Setup/Return

Press

SET +

CH –

ENTER

SET –

CH +

to select “JPEG Interval”.

Language Picture Sound Parental Other

E.B.L.

Tv Screen

Display

Off

JPEG Interval

Select Files

Off

All

/Enter/Setup/Return

Press ENTER or /

SET +

to select your desired time.

CH –

ENTER

SET –

CH +

Language Picture Sound Parental Other

E.B.L.

Tv Screen

Off

Display

JPEG Interval

5 Seconds

Select Files All

/Enter/Setup/Return

Off:

Plays back one file at a time.

5 Seconds:

Plays back images in the form of a slide show at 5 second intervals.

10 Seconds:

Plays back images in the form of a slide show at 10 second intervals.

15 Seconds:

Plays back images in the form of a slide show in 15 second intervals.

Advanced playback (DVD)

MP3/WMA/JPEG playback (continued)

SETUP

ENTER

▲ / ▼ / /

Setting the Select Files

When playing back a CD containing a mixture of MP3, WMA and JPEG files, only MP3/WMA or JPEG files can be displayed on the file menu.

1 Press SETUP in the stop mode.

Press or to select “Picture”, then press

ENTER.

VCR MENU

SETUP

Language Picture Sound Parental Other

To make SETUP screen disappear, press

SETUP.

VCR MENU

SETUP

SET +

CH –

ENTER

SET –

CH +

/Enter/Setup/Return

Press or to select “Select Files”.

SET +

CH –

ENTER

SET –

CH +

Language Picture Sound Parental Other

E.B.L.

Tv Screen

Off

4:3

On Display

JPEG Interval Off

Select Files All

/Enter/Setup/Return

Press ENTER or / to select your desired file type.

CH –

SET +

ENTER

SET –

CH +

Language Picture Sound Parental Other

E.B.L.

Tv Screen

Off

4:3

Display

JPEG Interval

Off

Select Files Pictures Only

/Enter/Setup/Return

All:

Displays all files.

Music Only:

Displays only MP3/WMA files.

Pictures Only:

Displays only JPEG files.

Advanced playback (DVD)

Zooming/Locating desired scene

DISPLAY

0–9

▲ / ▼ / /

JUMP

ZOOM

ENTER

CANCEL

DVD

VCD

Zooming

This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame.

Press ZOOM during playback.

CM SKIP

ZOOM

The centre part of the image will be zoomed in.

Each press of ZOOM will change the

ZOOM 1 (x 1.3), 2 (x 1.5) and 3

(x 2.0).

2 Press / / / to view a different part of the frame.

SET +

CH –

ENTER

SET –

CH +

You may move the frame from the centre position to UP, DOWN, LEFT or

RIGHT direction.

3 In the zoom mode press ZOOM repeatedly to return to a 1:1 view ( Off).

CM SKIP

ZOOM

Notes:

• You can select the Pause, Slow or Search playback in the zoom mode.

• Some discs may not respond to zoom feature.

DVD

VCD

Locating desired scene

Use the title, chapter and time recorded on the disc to locate the desired point to play back.

To check the title, chapter and time, press DISPLAY.

Press JUMP during playback or stop mode.

ZERO RETURN

JUMP

Jump Time

Title

Chapter

/Enter/0 9/Cancel/Jump

3 Press Numbered buttons (0–9) to change the number.

9 0

• If you input a wrong number, press

CANCEL.

• Refer to the package supplied with the disc to check the numbers.

CH –

Press or to select the “Time”, “Title” or

“Chapter”.

SET +

ENTER

SET –

CH +

Press ENTER. Playback starts.

CH –

SET +

ENTER

SET –

CH +

• When you change the title, playback starts from Chapter 1 of the selected title.

• Some discs may not work in the above operation.

Note:

In case of the Video-CD playback with PBC, the JUMP does not work. To turn off PBC, see page 43 .

ANGLE

ZOOM

▲ / ▼ / /

Zooming (JPEG CD)

This unit will allow you to zoom in on the JPEG image.

1 Press ZOOM during playback.

CM SKIP

ZOOM

Enlarged JPEG images are displayed.

You can make the images even larger by repeatedly pressing ZOOM.

2 Press / / / to view a different part of the frame.

SET +

CH –

ENTER

SET –

CH +

You may move the frame from the centre position to UP, DOWN, LEFT or

RIGHT direction.

1 2

3 In the zoom mode press ZOOM repeatedly to return to a 1:1 view ( Off).

CM SKIP

ZOOM Off 3

Changing angles (JPEG CD)

You can display JPEG images rotating at 90 degree intervals.

1 Press ANGLE during playback.

Images are rotated 90 degrees to the right.

COUNTER RESET

ANGLE

2 Press ANGLE repeatedly until the desired angle is selected.

Pressing ANGLE four times returns the image to its original angle.

COUNTER RESET

ANGLE • Images are displayed at the same angle until the disc is removed.

Marking desired scenes

The unit stores the points that you want to watch again up to 3 points.

You can resume playback from each scene.

DVD

VCD

Marking the scenes

1 Press MARKER during playback.

MARKER

Marker 1

Marker 2

Marker 3

/Enter/Cancel/Marker

▲ / ▼

MARKER

ENTER

CANCEL

DVD

VCD

Returning to the scenes

1 Press MARKER during playback or stop mode.

MARKER

Marker 1

Marker 2

Marker 3 02

/Enter/CancelMarker

2 Select the blank Marker using or .

Then press ENTER at the desired scene.

• Repeat this procedure to set the other 2 scenes.

SET + Marker 1

Marker 2

Marker 3

/Enter/Cancel/Marker

27 54

CH –

ENTER

SET –

CH +

3 Press MARKER to remove this display.

MARKER

2 Press or to select the Marker 1-3.

SET +

Marker 1

Marker 2

Marker 3

/Enter/Cancel/Marker

CH – CH +

ENTER

SET –

Press ENTER.

SET +

Playback starts from the marked scene.

CH –

ENTER

SET –

CH +

To cancel the Marker

Follow the above steps 1~2, then press CANCEL.

Notes:

•

Some discs may not work with the marking operation.

The marking is canceled when you open the disc tray or turn the power off.

Some subtitles recorded around the marker may fail to appear.

Advanced playback (DVD)

Repeat playback/A-B Repeat playback

PLAY MODE

A-B RPT

PLAY

DVD

VCD

Repeat playback of Title, Chapter and Track

1 Press PLAY MODE during playback or stop mode.

SP/SLP

PLAY MODE 1 Press A-B RPT during playback.

A-B RPT The start point is selected.

2 DVD

Press / or ENTER once or twice to select

“Chapter” or “Title”.

SET +

CH –

ENTER

SET –

CH +

Repeat

/Enter/Play Mode

Off Repeat :

/Enter/Play Mode

Chapter Repeat :

/Enter/Play Mode

Title

ENTER

▼ / /

DVD

VCD

A-B Repeat playback

A-B repeat playback allows you to repeat material between two selected points.

CH –

CD/VCD

Press to select “Repeat”.

Press / or ENTER once or twice to select

“Track” or “All”.

SET +

ENTER

SET –

CH +

Play Mode

Repeat

Off

/Enter/Play Mode

Play Mode

Repeat

Off

Track

/Enter/Play Mode

Play Mode

Repeat

Off

All

/Enter/Play Mode

2 Press A-B RPT again.

A-B RPT

The end point is selected. Playback starts at the point that you selected.

Playback stops at the end point, returns to Point A automatically, then starts again.

A B

3 Press PLAY MODE again to make the screen disappear.

Press PLAY to start Repeat playback.

To resume normal playback, select Repeat “Off”.

Notes:

Some discs may not work with the repeat operation.

To resume normal playback

Press A-B RPT again.

A-B RPT “

Off

” appears on the screen.

Notes:

• In A-B repeat mode, subtitles near point A or B may not appear.

• A-B Repeat playback is not available in multi-angle scenes.

• A-B Repeat playback does not work when Repeat playback is on.

• You may not be able to set A-B Repeat, depending on the scenes of the DVD.

• A-B repeat does not work with an interactive DVD, MP3/

WMA/JPEG CD and Video CD with PBC.

Advanced playback (DVD)

Changing angles/Title selection/DVD menu

ANGLE

PLAY

TOP MENU

ENTER

▲ / ▼ / /

Changing angles

When playing back a disc recorded with multi-angle facility, you can change the angle that you are viewing the scene from.

1 Press ANGLE during playback.

The current angle will appear.

COUNTER RESET

ANGLE

1/9

2 Press ANGLE repeatedly until the desired angle is selected.

COUNTER RESET

ANGLE

Note:

Depending on the DVD, you may not be able to change the angles even if multi-angles are recorded on the DVD.

Title selection

Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title.

1 Press TOP MENU during playback.

TOP MENU Title menu appears on the screen.

3 Press ENTER or PLAY.

SET +

The playback of the selected title will start.

CH – CH +

PLAY

ENTER

SET –

2 Press / or / to select the desired title.

SET +

CH – CH +

ENTER

SET –

Note:

Depending on the DVD, you may not be able to select the title.

Depending on the DVD, a “title menu” may simply be called a

“menu” or “title” in the instructions supplied with the disc.

DVD menu

Some DVDs allow you to select the disc contents using the menu.

When you play back these DVDs, you can select the subtitle language and sound-track language, etc. using the menu.

1 Press MENU during playback.

MENU

The DVD menu appears on the screen.

• Press MENU again to resume playback at the scene when you pressed MENU.

CH –

Press ENTER.

SET +

ENTER

SET –

CH +

The menu continues to another screen. Repeat steps 2 and 3 to set the item completely.

2 Press / or / to select the desired item.

SET +

Note:

Depending on the DVD, you may not be able to resume playback from the scene point when you pressed MENU.

CH –

ENTER

SET –

CH +

Program playback/Random playback (CD)

You can arrange the order of tracks on the disc.

0–9

PLAY MODE

PLAY

▲ / ▼ / /

ENTER

CANCEL

VCD

Program playback

1 Press PLAY MODE in the stop mode.

SP/SLP

PLAY MODE Play Mode : Off

Repeat : Off

/Enter/Play Mode

2 Press or to select Play Mode, then press

/ or to select “Program”.

SET +

CH –

ENTER

SET –

CH +

Play Mode

Repeat

Clear

: Program

: Off

6 9 12

Program Playback

/Enter/0–9/Cancel/Play Mode

4 Press / or / to select “Program

Playback” and press ENTER.

CH –

SET +

ENTER

SET –

CH +

The programmes you selected will start to playback in the order.

To return to normal playback, select

Play Mode: “Off”.

Play Mode

Repeat

1 9 4

Clear

Program

: Off

Program Playback

/Enter/0–9/Cancel/Play Mode

3 Press / or / to select the programming position. Use Numbered buttons (0–9) to input the Track numbers.

SET +

• To program others, repeat Step 3.

• If you input a wrong number, press

CANCEL.

CH –

ENTER

SET –

CH +

9 0

Play Mode

Repeat

3 11

Clear

: Program

: Off

9 12

Program Playback

/Enter/0–9/Cancel/Play Mode

To cancel program playback

Select “Clear” and press ENTER.

CH –

SET +

ENTER

SET –

CH +

• The program is canceled when you open the disc tray or turn the power off.

Note:

In playing back the Video CD with PBC, you cannot set

Program playback.

VCD

Random playback

1 Press PLAY MODE in the stop mode.

SP/SLP

PLAY MODE

3 Press PLAY.

PLAY

The Random Playback will start.

2 Press / to select Play Mode, then press

/ to select “Random”.

SET +

Play Mode : Random

Repeat : Off

/Enter/Play Mode

CH –

ENTER

CH +

SET –

Note:

In playing back the Video CD with PBC, you cannot set

Random playback.

Function setup (DVD)

Changing soundtrack language/

Setting surround sound

AUDIO

DVD

VCD

Changing soundtrack language

You can select the language when you play a multilingual disc.

1 Press AUDIO during playback.

AUDIO SELECT

AUDIO

The current soundtrack language will appear.

In case of Video CD playback

Audio type changes as follows each time you press AUDIO.

Spatializer Off

2/8 Fra Dolby Digital

Spatializer Off

2 Press AUDIO repeatedly until the desired language is selected.

AUDIO SELECT

AUDIO

The on-screen display will disappear after a few seconds.

Notes:

• If the desired language is not heard after pressing the button several times, the language is not recorded on the disc.

• Changing soundtrack language is canceled when you open the disc tray. The initial default language or available language will be heard if the disc is played back again.

DVD

VCD

Setting surround sound

This DVD/VCR equipped with a “SPATIALIZER VIRTUAL SURROUND”. It can produce the effect of being in a cinema or a concert hall.

During disc playback press AUDIO. 1

AUDIO SELECT

AUDIO

1/8 Eng Dolby Digital

Spatializer Off

To cancel Surround mode:

Follow the left steps 1~2, then press or to select the

“Off” position.

Note:

The “SPATIALIZER VIRTUAL SURROUND” is effective only for the sound of disc.

Press or to select “On”.

SET +

CH –

ENTER

SET –

CH +

1/8 Eng Dolby Digital

Spatializer On

Certain audio features of this product manufactured under a license from Desper Products, Inc. Spatializer ® and the circle-in-square device are trademarks owned by Desper

Products, Inc.

Function setup (DVD)

Setting subtitles/Karaoke playback

SUBTITLE

AUDIO

▲ / ▼ / /

Turning the subtitles on and off

When playing back a disc recorded with subtitles, you can turn the subtitles on or off.

Press SUBTITLE during playback until “Off” appears.

ATR

SUBTITLE Off

Note:

Depending on the DVD, you may not be able to turn the subtitles on even if they are recorded on it.

Depending on the DVD, you may not be able to turn the subtitles off.

Changing the subtitle language

You can select the language when playing back a disc recorded with multi-lingual subtitles.

Press SUBTITLE repeatedly during playback until your desired language appears.

ATR

SUBTITLE

1/32 Eng

The on-screen display will disappear after a few seconds.

Notes:

• Changing subtitle language is canceled when you open the disc tray.

• Depending on the DVD, you may not be able to change the subtitles even if multilingual subtitles are recorded on it. While playing the DVD, the subtitle may change when: -you open or close the disc tray -you change the title.

• In some cases, the subtitle language is not changed to the selected one immediately.

Karaoke playback

You can turn the vocal on or off recorded on the DVD KARAOKE.

1 During DVD KARAOKE disc playback, press

AUDIO.

AUDIO SELECT

AUDIO 1/8 Eng Dolby Digital

Spatializer Off

Notes:

• The vocal output feature is used during playback of

Dolby Digital (multi-channel) recorded DVD KARAOKE discs. This feature allows you to turn off vocal audio tracks, or restore them for background accompaniment.

• When playing Karaoke, connect appropriate audio equipment such as an amplifier to the DVD/VCR.

2 Press ▲ or ▼ until the KARAOKE symbol ( ) appears.

• If you play non-Karaoke disc, the KARAOKE symbol ( ) does not appear.

SET +

1/8 Eng Dolby Digital

CH – CH +

ENTER

Off

SET –

CH –

Press or to select “On” or “Off”.

SET +

CH +

On : The primary vocal is output when it is recorded on the disc.

Off : The primary vocal is not output.

ENTER

SET –

Function setup (DVD)

Setting the aspect ratio of TV screen

You can select the aspect ratio for your TV.

The following pages describe the setup/operation in DVD mode.

SETUP

RETURN

ENTER

▲ / ▼ / /

Setting the aspect ratio of TV screen

1 Press SETUP in the stop mode or No Disc.

Press or to select “Picture”.

CH –

VCR MENU

SETUP

SET +

ENTER

SET –

CH +

Language Picture Sound Parental Other

/Enter/Setup/Return

You have the following screen sizes to choose from:

4:3 Letter box:

Select this mode when connecting to a conventional TV.

When playing back a wide screen-DVD disc, it displays the wide picture with black bands at the top and bottom of screen.

4:3 Pan scan:

It displays the wide picture on the whole screen with left and right edges automatically cut off.

16:9 Wide:

Select this mode when connecting to a wide-screen TV.

A wide screen picture is displayed full size.

2 Press or ENTER, then press or to select

“Tv Screen”.

SET +

CH –

ENTER

SET –

CH +

Language Picture Sound Parental Other

E.B.L.

Tv Screen

Off

4:3

Display

JPEG Interval

Off

Select Files All

/Enter/Setup/Return

4 To make SETUP screen disappear, press SETUP or RETURN while the SETUP screen is being displayed.

VCR MENU

SETUP

RETURN 3 Press or ENTER.

Press or to select your desired screen type, then press ENTER.

SET +

CH –

ENTER

SET –

CH +

Language Picture Sound Parental Other

E.B.L.

Tv Screen

Off

4:3 4:3

Display

JPEG Interval

Off

Select Files All

/Enter/Setup/Return

4:3

16:9

Note:

If the DVD disc is not formatted in the pan & scan style, it displays 4:3 style.

E.B.L. (Enhanced Black Level)

To select the black level of playback pictures, set your preference and monitor’s ability.

SETUP

RETURN

ENTER

▲ / ▼ / /

Setting E.B.L.

1 Press SETUP in the stop mode or No Disc.

Press or to select “Picture”.

VCR MENU

SETUP Language Picture Sound Parental Other

4 To make SETUP screen disappear, press SETUP or RETURN while the SETUP screen is being displayed.

VCR MENU

SETUP

SET +

CH –

ENTER

SET –

CH +

/Enter/Setup/Return

RETURN

2 Press or ENTER, then press or to select

“E.B.L.”.

SET +

CH –

ENTER

SET –

CH +

Language Picture Sound Parental Other

E.B.L.

Tv Screen

Off

4:3

Display

JPEG Interval

Off

Select Files All

/Enter/Setup/Return

3 Press / or ENTER to select “On” or “Off”.

CH –

SET +

ENTER

SET –

CH +

Language Picture Sound Parental Other

E.B.L.

Tv Screen

Display

4:3

JPEG Interval

Select Files

Off

All

/Enter/Setup/Return

On: Enhanced grey scale (0 IRE cut off)

Off: Standard grey scale (7.5 IRE cut off)

DISPLAY

Setting on screen display/Status display of disc

SETUP

RETURN

ENTER

▲ / ▼ / /

Setting on screen display

On screen display can be switched on or off when you press the buttons.

1 Press SETUP in the stop mode or No Disc.

Press or to select “Picture”.

VCR MENU

SETUP

Language Picture Sound Parental Other

SET +

/Enter/Setup/Return

CH –

Press / or ENTER to select “On” or “Off”.

SET +

ENTER

SET –

CH +

Language Picture Sound Parental Other

E.B.L.

Tv Screen

Display

JPEG Interval

Off

4:3

Off

Select Files All

/Enter/Setup/Return

CH – CH +

ENTER

SET – On: On screen displays appear when you press the buttons (factory setting).

Off: On screen displays do not appear when you press any buttons.

2 Press or ENTER, then press or to select

“Display”.

SET +

CH –

ENTER

SET –

CH +

Language Picture Sound Parental Other

E.B.L.

Tv Screen

Off

4:3

On Display

JPEG Interval

Select Files

Off

All

/Enter/Setup/Return

4 To make SETUP screen disappear, press SETUP or

RETURN while the SETUP screen is being displayed.

VCR MENU

SETUP

RETURN

DVD

VCD

Status display of disc

Each press of DISPLAY, the status display of the disc will appear on the screen and change as follows.

DVD

00:34:56 01:12:33

Title

1/8

1/99

00:34:56 01:12:33

Chapter 1/999

Eng DolbyDigital

1/9

1/32 Eng

Video CD

00:12 04:32

Audio CD

Track 11/99

34:56 71:33

To make status display disappear, press DISPLAY again.

PBC

Track -/-

00:12 04:32

When you playback the CD disc, the status display will appear on the screen and continue displaying.

Function setup (DVD)

Dynamic Range Control

DRC (Dynamic Range Control) enables you to control the dynamic range so as to achieve a suitable sound for your equipment.

SETUP

RETURN

ENTER

▲ / ▼ / /

Dynamic Range Control

1 Press SETUP in the stop mode.

Press or to select “Sound”.

VCR MENU

SETUP

Language Picture Sound Parental Other

4 To make SETUP screen disappear, press SETUP or RETURN while the SETUP screen is being displayed.

VCR MENU

SETUP

SET +

CH –

ENTER

SET –

CH +

/Enter/Setup/Return

RETURN

2 Press or ENTER to select “Dialogue”.

SET +

Language Picture Sound

Dialogue Off

CH – CH +

ENTER

SET –

/Enter/Setup/Return

3 Press or ENTER, then press or to select desired setting.

SET +

Language Picture Sound Parental Other

Dialogue Off On : DRC(TV)

Off : DRC(Std)

CH –

ENTER

SET –

CH +

/Enter/Setup/Return

On:

Off:

Loud sound such as explosion or the like is toned down slightly when played back. This makes it suitable for when it is connected to a stereo.

It plays back at the recording level on the disc.

Notes:

• This function works only during playback of Dolby Digital recorded discs.

• The level of Dynamic Range Reduction may differ depending on DVD video disc.

Function setup (DVD)

To change the parental level

OPEN/CLOSE

0–9

SETUP

RETURN

ENTER

▲ / ▼ / /

To change the parental level

1 Press SETUP in the stop mode or No Disc.

Press or to select “Parental”.

Then press or ENTER.

VCR MENU

SETUP

Language Picture Sound Parental Other

Password

Parental 1

SET +

CH – CH +

ENTER

SET –

0–9/Cancel

/Enter/Setup/Return

5 Press or to select “Password”, then press number buttons (0–9) to enter the password.

SET +

Note: You can change the password if you want.

CH – CH +

ENTER

1 2

SET –

Language Picture Sound Parental Other

Password

Parental

9 8 7 6

9 0

0 9/Cancel

/Enter/Setup/Return

2 Press number buttons (0–9) to enter the password you have stored.

9 0

Language Picture Sound Parental Other

Password

Parental

1 2 3 4

0–9/Cancel

/Enter/Setup/Return

6 Press ENTER.

SET +

Now the parental level is changed and locked.

CH – CH +

ENTER

SET –

Language Picture Sound Parental Other

Password

Parental 5

0 9/Cancel

/Enter/Setup/Return

3 Press ENTER.

The rating is now unlocked.

SET +

CH – CH +

Language Picture Sound Parental Other

Password

Parental 1

ENTER

SET –

0–9/Cancel

/Enter/Setup/Return

7 Press SETUP or RETURN to remove the parental control screen.

VCR MENU

SETUP

RETURN

4 Press or to select “Parental”, then press

or to change the parental level.

SET +

Language Picture Sound Parental Other

Password

Parental 5

CH –

ENTER

SET –

CH +

0–9/Cancel

/Enter/Setup/Return

If you forget the password...

1. Press OPEN/CLOSE to open the disc tray.

2. Remove the disc.

3. Press OPEN/CLOSE again to close the disc tray.

“No Disc” appears on the screen.

4. While holding 7 down on the remote control, press

STOP on the front panel. “PASSWORD CLEAR” appears on the screen.

5. Enter a new password again.

Parental control setting

Some discs are specified not suitable for children. Such discs can be limited not to play back with the unit.

OPEN/CLOSE

0–9

▲ / ▼ / /

SETUP

RETURN

ENTER

CANCEL

Parental control setting

1 Press SETUP in the stop mode or No Disc.

Press or to select “Parental”. Then press

or ENTER.

VCR MENU

SETUP

Language Picture Sound Parental Other

Password

Parental Off

4 Press ENTER to store the password.

SET +

Note: Now the rating is locked and the setting cannot be changed unless you enter the correct password.

CH – CH +

ENTER

SET –

Language Picture Sound Parental Other

Password

Parental 1

CH –

SET +

ENTER

SET –

CH +

0–9/Cancel

/Enter/Setup/Return

0–9/Cancel

/Enter/Setup/Return

2 Press or to select “Parental”, then press

or until the level you require appears.

SET +

CH – CH +

Language Picture Sound Parental Other

Password

Parental 1 ENTER

SET –

5 Press SETUP or RETURN to remove the parental control screen.

VCR MENU

SETUP

RETURN

/Enter/Setup/Return

• Level Off: The parental control setting does not function.

• Level 8: All DVD software can be played back.

• Level 1: DVD software for adults cannot be played back.

• Select from the level 1 to level 8. The limitation will be more severe as the level number is lower.

6 Press OPEN/CLOSE to activate parental control setting.

OPEN/CLOSE

3 Press or to select “Password”.

Press number buttons (0-9) to input a 4-digit password.

SET + Language Picture Sound Parental Other

Password

Parental

1 2 3 4

CH –

ENTER

CH +

SET –

0–9/Cancel

/Enter/Setup/Return

1 2 3

9 0

Be sure to remember this number!

• If you input a wrong number, press CANCEL.

Notes:

• If each setup (pages 57~66) has been completed, the unit can always be worked under the same conditions (especially with DVD discs).

Each setup will be retained in the memory if you turn the power off.

• Depending on the discs, the unit cannot limit playback.

• Some discs may not be encoded with specific rating level information though its disc jacket says “adult”. For those discs, the age restriction will not work.

Temporary disabling of rating level by DVD disc

Depending on the DVD disc, the disc may try to temporarily cancel the rating level that you have set.

It is up to you to decide whether to cancel the rating level or not.

OPEN/CLOSE

0–9

PLAY

▲ / ▼

RETURN

ENTER

Temporary disabling of rating level by DVD disc

1 Load a DVD disc and press PLAY or OPEN/

CLOSE on the unit (see page 42).

PLAY

OPEN/CLOSE

Enter the password with number buttons (0–9).

Then press ENTER.

2 3

If you interrupt the entering, press

RETURN.

4 5 6

7 8 9 0

Please enter the

SET +

CH – CH +

Enter/0 9/Cancel/Return

ENTER

SET –

2 If the DVD disc has been designed to temporarily cancel the Rating level, the screen which follows the “Reading” screen will change, depending on which disc is played. If you select “YES” with the

ENTER key, “Your disc exceeds the parental control level#.” screen will then appear.

Reading

Your disc exceeds the parental control level#.

Parental Control Level

Cancel Picture

/Enter/Return

RETURN

Playback will commence if the entered password was correct.

3 If you wish to cancel the set rating level temporarily, select “Parental Control Level” with or , then press ENTER. If the 4-digit password at step 2 on page 62 has been set, the password entering screen will appear as shown in step 4.

Alternatively, if the password has not been set, playback will commence. If you don’t know (or have forgotten) the password, select “Cancel Picture”.

The setting screen will disappear. Press OPEN/

CLOSE to remove the disc.

Note:

This temporary cancellation of rating level will be kept until the disc is ejected.

When the disc is ejected, the original rating level will be set again automatically.

SET +

CH –

ENTER

SET –

CH +

OPEN/CLOSE

Function setup (DVD)

Setting OSD language

The setup language can be selected.

SETUP

RETURN

ENTER

▲ / ▼ / /

DVD

VCD

Setting OSD language

1 Press SETUP in the stop mode or No Disc.

Press or to select “Other”.

VCR MENU

SETUP Language Picture Sound Parental Other

SET +

CH –

ENTER

SET –

CH +

/Enter/Setup/Return

4 To make SETUP screen disappear, press SETUP or RETURN while the SETUP screen is being displayed.

VCR MENU

SETUP

RETURN

2 Press or ENTER to select “OSD Language”.

SET +

Language Picture Sound Parental Other

OSD Language English

CH –

ENTER

CH +

SET –

If the unit does not operate properly: Static electricity, etc., may affect the player's operation. Disconnect the

AC power cord once, then connect it again.

/Enter/Setup/Return

3 Press or ENTER and then press or to select desired language (e.g. English), then press ENTER.

CH –

SET +

CH +

Language Picture Sound Parental Other

OSD Language English English

Francais

Espanol

ENTER

SET –

/Enter/Setup/Return

Function setup (DVD)

Selecting PROGRESSIVE scan

The progressive scan capability provides the highest resolution pictures with less flicker and line structure.

If you are using the Component video jacks, but are connecting the DVD/VCR to a standard (analog) television, set PROGRESSIVE to Off.

If you are using the Component video jacks for connection to a TV or monitor that is compatible with a progressive scan signal, set PROGRESSIVE to On.

VCR DVD

DVD

VCD

Selecting PROGRESSIVE scan

Preparation:

• Connect to a TV equipped with component jacks.

• Turn ON the TV and set it to the corresponding video input mode.

• Set the S-VIDEO/COMPONENT video selector switch on the rear panel to COMPONENT position.

• Press VCR DVD selector to select the DVD mode. (The

DVD indicator will light.)

Press PROGRESSIVE in the stop mode.

INPUT SELECT

PROGRESSIVE

The progressive indicator “ ” on the display window will light.

• The unit recognizes the picture source (film or video) of the current disc according to the disc information.

Press PLAY to start playback.

PLAY

There are two types of source content in pictures recorded in

DVD video discs: film content (pictures recorded from films at 24 frames per second) and video content (video signals recorded at 30 frames per second).

When the unit plays back a film source material, uninterlaced progressive output signals are created using the original information. When a video content is played back, the unit interleaves lines between the interlaced lines on each to create the interpolated picture and outputs as the progressive signal.

To select PROGRESSIVE scan Off

Press PROGRESSIVE in the stop mode.

The progressive indicator “ ” on the display window will go off.

Notes:

• Some discs may not be played back with the progressive scanning mode correctly because of the disc characteristics or recording condition.

• If your TV does not accept the progressive scan format, the picture will appear scrambled if you select progressive scan output from the unit. In such a case, select PROGRESSIVE scan Off.

• Once PROGRESSIVE scan On, all other video outputs are disabled except component video outputs.

• You cannot make the progressive scanning mode active in following cases.

– The unit is in the VCR mode.

– The disc is played back in the DVD mode.

– The S-VIDEO/COMPONENT video selector switch is set to

S-VIDEO position.

Setting language

You can select the language of “Menu”, “Subtitle” and “Audio” if their languages are recorded onto the disc more than one language.

SETUP

RETURN

ENTER

▲ / ▼ / /

Setting language

Press SETUP in the stop mode or No Disc.

Press or to select “Language”.

VCR MENU

SETUP

Language Picture Sound Parental Other

4 To make SETUP screen disappear, press SETUP or RETURN while the SETUP screen is being displayed.

VCR MENU

SETUP

RETURN

SET +

CH –

ENTER

SET –

CH + /Enter/Setup/Return

2 Press or ENTER, then press or to select desired langugage item.

SET +

CH –

ENTER

SET –

CH +

Language Picture Sound Parental Other

Subtitle

Audio

English

Automatic

English

Note:

If the selected language is not recorded on the disc, the firstpriority language is selected.

/Enter/Setup/Return

3 Press or ENTER.

Press or to select your desired language, then press ENTER.

SET +

CH –

ENTER

SET –

CH +

Language Picture Sound Parental Other

Subtitle

Audio

English

Automatic

English

Francais

Espanol

Other

/Enter/Setup/Return

English, Francais, Espanol:

The selected language will be heard or seen.

Other:

Other language can be selected (see “Language code list” on page 67).

Original: (Audio)

The unit will select the first priority language of each disc.

Automatic: (Subtitle)

• The unit will automatically select the same language in the AUDIO setting.

• When the unit selects the same language as the AUDIO, the subtitles will not appear during playback.

• When you do not use the same language as the AUDIO, the subtitles will appear during playback.

Off: (Subtitle)

Subtitles do not appear.

Others

Language code list

Enter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio” (see page 65).

Bihari

Breton

Bulgarian

Burmese

Byelorussian

Cambodian

Catalan

Chinese

Corsican

Croatian

Czech

Danish

Dutch

English

Esperanto

Estonian

Faroese

Language Name Code Language Name Code Language Name Code Language Name Code

Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919

Afar

Afrikaans

Albanian

1111 Finnish

1116 French

2927 Frisian

1619 Lithuanian

1628 Macedonian

1635 Malagasy

2230 Slovak

2321 Slovenian

2317 Somali

2921

2922

2925

Amharic

Arabic

Armenian

Assamese

Aymara

1123 Galician

1128 Georgian

1835 German

1129 Greek

1135 Greenlandic

Azerbaijani

Bashkir

1136 Guarani

1211 Gujarati

Basque 1531 Hausa

Bengali; Bangla 1224 Hebrew

Bhutani 1436 Hindi

1722

2111

1415

1522

2122

1819

Malay

Malayalam

Maltese

Maori

Marathi

1724 Moldavian

1731 Mongolian

1811 Nauru

1933 Nepali

Norwegian

2329

2322

2330

2319

2328

Spanish

Sundanese

Swahili

Swedish

Tagalog

2325 Tajik

2324 Tamil

2411 Tatar

2415 Telugu

2425 Thai

1529

2931

2933

2932

3022

3017

3011

3030

3015

3018

1218 Hungarian

1228 Icelandic

1217 Indonesian

2335 Interlingua

1215 Irish

2123 Italian

1311 Japanese

3618 Javanese

1325 Kannada

1828 Kashmiri

1329 Kazakh

1411 Kirghiz

1831 Oriya

1929 Panjabi

1711 Polish

1930 Portuguese

2011 Quechua

2528 Tibetan

2611 Tigrinya

1924 Pashto, Pushto 2629 Tonga

1911 Persian 1611 Turkish

2622

2630

2731

Turkmen

Twi

Ukrainian

1225

3019

3025

3028

3021

3033

3121

2033 Rhaeto-Romance2823 Urdu

2124 Romanian 2825 Uzbek

2129 Russian

2121 Samoan

2135 Sanskrit

2831

2923

2911

Vietnamese

Volapük

Welsh

3128

3136

3219

3225

1335

2422 Korean

1524 Kurdish

1525 Laothian

1530 Latin

2125

2131

2225

2211

Scots Gaelic

Serbian

Shona

1625 Latvian, Lettish 2232 Sindhi

1714

2928

Serbo-Croatian 2918

2924

2914

Wolof

Xhosa

Yiddish

Yoruba

Zulu

3325

3418

2019

3525

3631

Others

Troubleshooting

Before calling a service technician, please check the following table for a possible cause of the symptoms and some solutions.

Symptoms Solutions

DVD/VCR

DVD/VCR does not operate.

No picture.

No sound.

The remote control does not function.

No Cable TV reception.

• Make sure the power cord is plugged in.

• Try another AC outlet.

• Unplug unit, then plug it back in.

• Select the DVD or VCR mode before operating.

• Antenna connection is not correct or antenna cable is disconnected.

• The video channel is not in the correct position or the TV is not set to the video channel 3 or 4.

• Check the unit is connected correctly.

• The video input selector of the TV is not set to VIDEO. Set to VIDEO (or equivalent).

• Channel is set to the external mode.

• Check the unit is connected correctly.

• Check the input selector of the amplifier is set properly.

• The unit is in the Special playback mode.

• Aim the remote control at the remote sensor.

• Operate within Approx. 7 Meters or reduce the light in the room.

• Clear the path of the beam.

• The batteries are weak. Replace the batteries.

• Check the batteries are inserted correctly.

• Check all Cable TV connections.

• Station or Cable TV system problems, try another station.

VCR

TV recording does not work.

Timer recording does not work.

Noise bars on screen.

• The erase prevention tab of the video cassette is broken off.

• The unit is in the external input mode.

• The time is not set correctly.

• The recording start/end time is not set correctly.

• The TIMER REC has not been pressed ( is not lit).

• Tracking adjustment beyond range of automatic tracking circuit. Try Manual tracking adjustment.

• Video heads are dirty.

• The tape is worn or damaged.

DVD

Display is not shown in your language.

Playback doesn’t start.

• Select proper language in the menu options.

• No disc is inserted.

• The disc may be dirty. Clean up the disc.

• The unit cannot play DVD-ROMs, etc.

Stopping playback, slow-motion play, repeat play, or memory play, etc. cannot be performed.

• Some discs may not do some of the functions.

No picture, or the screen is blurred or divided into two parts.

No 4:3 (16:9) picture.

No on-screen display.

No surround sound.

• The S-VIDEO/COMPONENT selector is not set correctly.

• The PROGRESSIVE scan is On although the unit is connected to a TV via the VIDEO OUT or the S-VIDEO OUT jack.

• The setup does not match your TV.

• Select Display “On”.

• The setup does not match your stereo system.

The unit or remote operation key is not functioning.

Playback does not start when the title is selected.

Audio soundtrack and/or subtitle language is not changed when you play back a DVD.

• Turn off the unit and unplug the AC power cord for several minutes, then replug it.

• Check the Parental setup.

• Multilingual language is not recorded on the DVD disc.

No subtitle.

Angle cannot be changed.

• Some discs have no subtitles.

• Subtitles are cleared. Press SUBTITLE.

• Multi-angles are not recorded on the DVD disc.

appears on the screen.

• The function is prohibited with the unit or the disc.

Page

16,17

–

29,34

–

30,42

14~17

14~19

–

14~19

–

31,44

–

61,62

Others

Limited warranty

Specifications

General

Power supply

Power consumption

Weight

Dimensions

Tuner

Antenna input/output

RF channel output

Color system

Video head

Audio track

Hi-Fi frequency response

Hi-Fi dynamic range

F.FWD/REW time at 25˚C (77˚F)

Applicable disc

Frequency range

S/N ratio

Harmonic distortion

Wow and flutter

Operating conditions

Input/Output

AC 120 V 60 Hz

Operation: 18 W, Stand by: 2 W

7.7 lbs (3.5 kg)

Width: 16-15/16 inches (430 mm)

Height: 3-7/8 inches (99 mm)

Depth: 8-13/16 inches (224.5 mm)

181 channel freq. synthesized

VHF 2-13

UHF 14-69

Cable TV 113 Channels

UHF/VHF In/Out: 75

Ω coaxial

Channel 3 or 4, Switchable

NTSC

4 Rotary heads

Hi-Fi sound - 2 Tracks / MONO sound - 1 Track

20 Hz to 20,000 Hz

More than 90dB

Approx. 1 minute and 48 seconds (with T-120 Cassette Tape)

DVD (12 cm, 8 cm), CD (12 cm, 8 cm)

DVD: 4 Hz-22 kHz, CD: 4 Hz-20 kHz

90dB (DVD)

0.02% (DVD)

Less than 0.01% Wrms

Temperature: 5˚C-40˚C (41˚F-104˚F), Operating status: Horizontal

DVD/VCR

Video input

Video output

Audio input

Audio output

1.0 V (p-p), 75

Ω

, negative sync., pin jack x 2

1.0 V (p-p), 75

Ω

, negative sync., pin jack x 1

–8 dBm, 50 k

Ω

, negative sync., pin jack (L/R) x 2

–8 dBm, 1 k

Ω

, negative sync., pin jack (L/R) x 1

DVD

S-video output

Component video output

(Y) 1.0 V (p-p), 75

Ω

, negative sync., Mini DIN 4-pin x 1

Ω

(Y) 1.0 V (p-p), 75

Ω

, negative sync., pin jack x 1

)/(P

) 0.7 V (p-p), 75

Ω

, pin jack x 2

0.5 V (p-p), 75

Ω

, pin jack x 1 Audio output (BITSTREAM/PCM

COAXIAL)

Audio output (BITSTREAM/PCM

OPTICAL)

Optical connector x 1

Audio output (ANALOG) –12 dBm, 1 k

Ω

, pin jacks (L, R) x 1

S-VIDEO/COMPONENT video selector Slide switch x 1

Supplied accessories

Audio/video cable ................................................. 1

Remote control (SE-R0108) ................................. 1

Batteries (R03/AAA) ............................................. 2

75 ohm coaxial cable ............................................ 1

• Designs and specifications are subject to change without notice.

70 71

Hello! I am an AI chatbot specifically trained to assist you with the Toshiba SD-K531SU2 DVD & Blu-ray User Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated