Toshiba SD7300KU DVD & Blu-ray User Guide

Toshiba SD7300KU DVD & Blu-ray User Guide
Introduction
2
Connections
13
Basic playback
18
Function setup
21
Others
24
DIGITAL VIDEO
DVD PLAYER
SD7300KU
OWNER’S MANUAL
Owner’s Record
The model number and serial number are on the back of
your DVD Player. Record these numbers in the spaces
below. Refer to these numbers whenever you communicate
with your Toshiba dealer about this DVD Player.
Model number:
Serial number:
© 2010 Toshiba Corporation
Introduction
SAFETY PRECAUTIONS
The lightning flash with an arrowhead symbol, within the equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within the equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in this owner’s manual.
CAUTION: VISIBLE LASER RADIATION WHEN
OPEN. DO NOT STARE INTO BEAM.
AVIS
WARNING: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS
HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN
THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT OF AC POWER OUTLET, THEN FULLY INSERT.
FCC NOTICE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
WARNING: Changes or modifications to this unit not expressly
approved by Toshiba, or parties authorized by Toshiba, could
void the user’s authority to operate the equipment.
CLASS 1
LASER PRODUCT
The symbol for Class
(Double lnsulation)
CAUTION: This Digital Video Disc Player employs a Laser
System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference. Should the unit
require maintenance, contact an authorized service location.
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure. To prevent direct exposure to laser beam,
do not try to open the enclosure. Visible and invisible laser
radiation when open and interlocks defeated. DO NOT STARE
INTO BEAM.
Warnings:
• The main plug is used as disconnect device and it should
remain readily operable during intended used. In order to
disconnect the apparatus from the mains completely, the
main plug should be disconnected from the mains socket
outlet completely.
• The apparatus shall not be exposed to dripping or splashing
and that no objects filled with liquid, such as vases, shall be
placed on the apparatus.
• Minimum 10 cm (4 inches) distances around the apparatus
for sufficient ventilations.
• The ventilation should not be impeded by covering the
ventilation openings with items such as newspaper, tablecloths, curtains, etc.
• No naked flame sources such as lighted candles should be
placed on the apparatus.
• The use of apparatus in moderate climates.
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any of the ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the
obsolete outlet.
2
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination Portable Cart
Warning
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as the power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
ADDITIONAL SAFETY INSTRUCTIONS
21.
22.
23.
24.
• in a confined space such as a bookcase, built-in cabinet,
or any other place with poor ventilation.
The slots and openings are provided to protect the unit from
overheating and to help maintain reliable operation.
Do not use a cracked, deformed, or repaired disc. These
discs are easily broken and may cause serious personal
injury and apparatus malfunction.
If the apparatus should emit smoke or an unusual odor,
immediately disconnect the power cord from the wall outlet.
Wait until the smoke or smell stops, then ask your dealer for
a check and repair. Neglecting to do so may cause fire.
During thunderstorms, do not touch the connecting cables
or the apparatus.
Warning: To prevent spread of fire, keep candles or other
open flames away from this product at all times.
Introduction
15. Do not overload wall outlets; extension cords, or integral
convenience receptacles as this can result in a risk of fire
or electric shock.
16. Never expose the apparatus to dripping or splashing or
place items such as vases, aquariums, any other item
filled with liquid, or candles on top of the unit.
17. Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
18. Do not place anything on top of this unit.
19. Do not place the apparatus on amplifiers or equipment
that may produce heat.
20. Never block or cover the slots or openings in the unit.
Never place the unit:
• on a bed, sofa, rug or similar surface;
• too close to drapes, curtains, or walls; or
Location of the required label
The rating plate
a n d t h e s a fe t y
caution are on the
rear of the unit.
ENERGY STAR® qualified DVD. Products
that earn the ENERGY STAR prevent
green house gas emissions by meeting
strict energy efficiency guidelines set by the
U.S. Environmental Protection Agency and
the U.S. Department of Energy. ENERGY
STAR and the ENERGY STAR mark are
registered U.S. marks.
PRECAUTIONS
Notes on handling
When shipping the DVD player, the original shipping
carton and packing materials come in handy. For
maximum protection, repack the unit as it was originally
packed at the factory. Take care not to give it a shock or
shake when carrying.
Do not use volatile liquids, such as insect spray, near
the DVD player. Do not leave rubber or plastic products
in contact with the DVD player for a long time. They will
leave marks on the finish.
The top and rear panels of the DVD player may
become warm after a long period of use. This is not a
malfunction.
When the DVD player is not in use, be sure to remove
the disc and turn off the power.
If you do not use the DVD player for a long period, the
unit may not function properly in the future. Turn on and
use the DVD player occasionally.
Notes on locating
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe it
dry.
Do not use any type of solvent, such as thinners and
benzene, as they may damage the surface of the DVD
player.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
Inspection and Maintenance
This DVD player is a high technology, precision device. If
the optical pick-up lens and disc drive parts become dirty
or worn down, the picture quality may be reduced. To avoid
reduction in picture quality, it is recommended that regular
inspection and maintenance (cleaning or parts replacement)
be performed every 1,000 hours of use. For further details,
contact your nearest consumer electronics dealer.
Place the DVD player on a level surface. Do not use it on
a shaky or unstable surface such as a wobbling table or
inclined stand. The loaded disc may come off the proper
position and cause damage to the DVD player.
When you place this DVD player near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, place the DVD
player away from the TV, radio, or VCR.
3
Introduction
PRECAUTIONS
Notes on moisture condensation
Moisture condensation damages the DVD player.
Please read the following carefully.
NOTES ON DISCS
On handling discs
Do not touch the playback side of the disc.
Moisture condensation occurs, for example, when you pour
a cold drink into a glass on a warm day. Drops of water form
on the outside of the glass. In the same way, moisture may
condense on the optical pick-up lens inside this unit, one
of the most crucial internal parts of the DVD player.
Playback side
Do not attach paper or tape to discs.
Moisture condensation occurs during the following
cases.
When you bring the DVD player directly from a cold
place to a warm place.
When you use the DVD player in a room where you just
turned on the heater, or a place where the cold wind
from the air conditioner directly hits the unit.
In summer, when you use the DVD player in a hot and
humid place just after you move the unit from an air
conditioned room.
When you use the DVD player in a humid place.
On cleaning discs
Fingerprints and dust on the disc cause picture and sound
deterioration. Wipe the disc from the center outwards with
a soft cloth. Always keep the disc clean.
If you cannot wipe off the dust with a soft cloth, wipe the
disc lightly with a slightly moistened soft cloth and finish
with a dry cloth.
Do not use any type of solvent such as thinner, benzine,
commercially available cleaners or antistatic spray for vinyl
LPs. It may damage the disc.
On storing discs
Do not use the DVD player when moisture
condensation may occur.
If you use the DVD player in such a situation, it may
damage discs and internal parts. Remove the disc,
connect the power cord of the DVD player to the wall
outlet, turn on the DVD player, and leave it for two or
three hours. After two or three hours, the DVD player will
have warmed up and evaporated any moisture. Keep the
DVD player connected to the wall outlet and moisture
condensation will seldom occur.
Do not store discs in a place subject to direct sunlight or
near heat sources.
Do not store discs in places subject to moisture and dust
such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing objects
on discs outside of their case may cause warping.
On VIDEO CDs
This DVD player supports VIDEO CDs equipped with the PBC
(Version 2.0) function. (PBC is the abbreviation of Playback
Control.) You can enjoy two playback variations depending on
types of discs.
• VIDEO CD not equipped with PBC function (Version 1.1)
Sound and movie can be played on this DVD player in the
same way as an audio CD.
• VIDEO CD equipped with PBC function (Version 2.0)
In addition to operation of a VIDEO CD not equipped with the
PBC function, you can enjoy playback of interactive software
with search function by using the menu displayed on the TV
screen (Menu Playback). Some of the functions described in
this owner’s manual may not work with some discs.
4
About this owner’s manual
Playable discs
This DVD player can play the following discs.
Disc Mark
Disc
Size
Maximum
playback time
Approx. 4 hours
(single sided disc)
Audio
+
video
(moving
pictures)
DVDs
About
The
icons on the heading bar show the
playable discs for the function described under that heading.
DVD : You can use this function with DVD discs.
: You can use this function with Video CDs.
CD : You can use this function with Audio CDs/CD-R/RW
CDs.
Contents
Introduction
This owner’s manual explains the basic instructions of
this DVD player. Some DVDs are produced in a manner
that allows specific or limited operation during playback.
As such, the DVD player may not respond to all operating
commands. This is not a defect in the DVD player. Refer
to instruction notes of discs.
” may appear on the TV screen during operation.
“
” means that the operation is not permitted by the
A“
DVD player or the disc.
12 cm
Approx. 8 hours
(double sided disc)
Approx. 80 minutes
(single sided disc)
8 cm
VIDEO
CDs
DIGITAL VIDEO
Audio
+
video
(moving
pictures)
Approx. 160 minutes
(double sided disc)
12 cm
Approx. 74 minutes
8 cm
Approx. 20 minutes
12 cm
Approx. 74 minutes
8 cm
(CD
single)
Approx. 20 minutes
12 cm
35 min.
8 cm
10 min.
Notes on region numbers
The region number of this DVD player is 1. If region
numbers, which stand for their playable area, are printed
Audio
CDs
Audio
or
, disc playback
on your DVD and you do not find
will not be allowed by the player. (In this case, the DVD
player will display a message on-screen).
Notes on copyright
The unauthorized recording, use, distribution, or revision of
copyrighted materials including, without limitation, television
programs, videotapes, and DVDs, is prohibited under the
Copyright Laws of the United States and other countries,
and may subject you to civil and criminal liability.
SUPER
VIDEO
CDs
SUPER VIDEO
Audio
+
video
(moving
pictures)
The following discs are also available.
DVD±R/±RW and DVD-ROM discs of DVD format
CD-R/CD-RW discs of CD-DA, Video CD, MP3 or
JPEG format
Some of these discs may be incompatible.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection • You cannot play discs other than those listed above.
technology must be authorized by Macrovision Corporation, • You cannot play DVD-RAM discs or non-standardized
and is intended for home and other limited viewing uses only
discs, etc., even if they may be labeled as above.
unless otherwise authorized by Macrovision Corporation. • This DVD player uses the NTSC color system, and
Reverse engineering or disassembly is prohibited.
cannot play DVDs recorded in any other color system
(PAL, SECAM, etc.).
Because of problems and errors that can occur during the
creation of DVD and CD software and/or the manufacture
of DVD and CD discs, Toshiba cannot assure that this DVD
player will successfully play every disc bearing the DVD
and CD logos. If you happen to experience any difficulty
playing a DVD and/or CD disc on this DVD player, please
contact Toshiba Customer Service.
is a trademark of DVD Format/Logo Licensing
Corporation.
5
Introduction
Table of Contents
Introduction
SAFETY PRECAUTIONS ...........................
IMPORTANT SAFETY INSTRUCTIONS ....
PRECAUTIONS ..........................................
NOTES ON DISCS .....................................
Function setup
2
2
3
4
Notes on region numbers ................................... 5
Table of Contents ...................................... 6
Identification of Controls ......................... 7
Front panel ...........................................................7
Rear panel ...........................................................7
DVD display ........................................................7
Using the Remote Control ........................ 8
Loading batteries .................................................8
Operating with the remote control ........................8
Remote control ....................................................9
Names and functions .........................................10
Connections
Connecting to a TV ................................... 13
Connecting to a TV ............................................ 13
Connecting to a TV (Using the component video
jacks).................................................................. 13
Connecting to a display (Using a HDMITM cable) .......14
Connecting to Optional Equipment ........ 15
Connecting to an amplifier equipped with a
Dolby® Digital decoder ...................................... 16
Connecting to an amplifier equipped with
Dolby Surround Pro Logic ................................. 16
Connecting to an amplifier equipped with a
DTS® decoder ................................................... 17
Connecting to an amplifier equipped with an
MPEG2 audio decoder ..................................... 17
Connecting to an amplifier equipped with a
digital audio input .............................................. 17
Basic playback
Playing a Disc ........................................... 18
Basic playback .................................................. 18
Playing MP3/JPEG Files ........................... 19
Playing MP3/JPEG Files ................................... 19
Using a SD/SDHC Card ............................. 20
Inserting a SD/SDHC Card ............................... 20
6
Customizing the Function Settings.......... 21
Using the Language setup menu ........................21
Using the Video setup menu ...............................21
Using the Audio setup menu ...............................22
Using the Rating setup menu..............................22
Using the TV System setup menu.......................23
Others
Before Calling Service Personnel............. 24
Specifications............................................. 25
Limited Warranty ........................................ 26
Identification of Controls
See the page in
for details.
Front panel
Introduction
HDMI indicator 14
18
10
11
8
7
11
10
HDMI SELECT
14
SD/SDHC card slot
20
Rear panel
13
Power Cord
HDMI OUT
jack
14
13
Y
VIDEO
PB
PR
VIDEO OUT
AUDIO
OUT
HDMI OUT
R
ANALOG
L
COAXIAL DIGITAL
16
17
13
DVD display
The indicators vary depending on the kinds of discs you play.
No disc
Bad disc
OPEN
LOAD/CLOSE
DVD VIDEO
VIDEO CD
Audio CD
SD Card
• During playback:
Example
• During playback:
Example
• During playback:
Example
• In SD mode with
no card inserted:
Some discs may only
display chapter numbers.
Some discs may only
display track numbers.
Some discs may only
display track numbers.
Power off
Title/Chapter/Track
number Indicator
Multifunctional indicator
(indicates operating
status or messages, etc.)
7
Introduction
Using the Remote control
Loading batteries
1
Open the cover.
2
Insert batteries (R03/AAA size).
Operating with the remote control
Point the remote control at the remote
sensor and press the buttons.
Distance: About 7 m (23 feet) from the front of the
remote sensor
Angle:
About 30° in each direction of the front of
the remote sensor
Make sure to match the + and – on the batteries to
the marks inside the battery compartment.
Caution
Never throw batteries into a fire.
Notes
• Be sure to use R03/AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Attention should be drawn to the environmental aspects
of battery disposal.
• Do not mix different battery types or combine used
batteries with new ones.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace both batteries
with new ones.
• If the batteries are dead or if you will not be using the
remote control for a long time, remove the batteries
to prevent battery acid from leaking into the battery
compartment.
8
* Do not expose the remote sensor of the DVD player
to a strong light source such as direct sunlight or
other illumination. If you do so, you may not be able
to operate the DVD player via the remote control.
Notes on the remote control
• Direct the remote control at the remote sensor of the DVD
player.
• When using the remote control, press the buttons at
intervals of about 1 second to ensure the correct mode
of operation.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot
or humid place.
• Do not spill water or put anything wet on the remote
control.
• Do not open the remote control.
• If the remote control is not going to be used for a long
time, remove the battery to avoid damage caused by
battery leakage corrosion.
CAUTIONS:
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
• Do not dispose of battery in fire; battery may explode or
leak.
• When discarding batteries, environmental problems must
be considered and local rules or laws governing the
disposal of these batteries must be strictly followed.
Remote control
1.
2. ON/STANDBY button 10
10
3.
for details.
Introduction
The instructions in this manual describe the functions on the remote control. See the page in
10
18. SEARCH (T) button 11
4.
5.
10
MUTE
10
6.
22.
23.
24.
10
7.
19. MUTE button 11
11
20.
21.
10
8.
10
8.
10
9.
10
9.
25.
10
10.
11.
12.
13.
10
15.
27.
28.
29.
10
14.
10
11
DVD
16.
11
26.
10
10
11
17. DVD button 11
* RETURN button
Return to menu display for VCD (2.0) discs with menu
(PBC should be ON).
SD
30.
31.
32.
11
11
11
11
12
12
12
* 12
12
12
12
33. HDMI button 12
34. SD button 12
* MENU button
Use the MENU button to display the menu included on
many DVDs.
9
Introduction
Names and functions
1. OPEN/CLOSE button
• Press to open/close the disc tray.
• The function is the same as the OPEN/CLOSE button on
the front panel.
2. ON/STANDBY button
Turn the unit on or set the unit to standby mode.
3. Number buttons
Press number buttons to play relevant chapter/track.
4. E.A.M button (Enhanced Audio Mode)
Use to select the sound enhancement on or off.
3D*:
To obtain expansive virtual surround sound effects from
two speakers. To use this enhancement on sounds output
from the ANALOG AUDIO OUT jacks, be sure to set
“Digital out” to “PCM”.
* Effective in playback of a DVD .
Notes
• Actual effects to sounds may vary depending on the speaker
system. Make selection according to your preference.
• Actual effects to sounds may vary depending on the disc.
• When the DVD player is connected to an amplifier
equipped with Dolby Surround Pro Logic, select “3D
effect”. Otherwise, Dolby Surround Pro Logic may function
differently than usual.
• The sound effect might not be heard easily on small TVs.
• The sound effect can be heard more easily at higher
volume.
• The sound effect might take a few seconds to be heard
after turning on the E.A.M.
5. E.P.M button (Enhanced Picture Mode)
Use to select the picture enhancement.
Brightness 1
6
12
Contrast
6
12
1
Select the picture enhancement by pressing / , then
press / to make your selections.
To exit the picture enhancement selection, press E.P.M
again.
8. SKIP buttons
To locate succeeding chapters or tracks.
To locate preceding chapters or tracks.
9. REV/FWD buttons
REV: Fast reverse playback
FWD: Fast forward playback
Each time you press the REV or FWD button, the playback
speed changes.
10. Direction buttons
Use / / / to select a selection in setup menu.
11. TOP MENU button
Display the title menu on DVD.
12. PLAY MODE button
While playing a disc, press the PLAY MODE button
repeatedly to select a repeat mode.
For DVD:
- Repeat Chapter (currently playing chapter)
- Repeat Title (currently playing title)
- Repeat All (entire disc)
- Off (cancel)
For Video CD, Audio CD:
- Repeat Single (currently playing track)
- Repeat All (entire disc)
- Off (cancel)
For MP3, JPEG:
- Repeat Single (currently playing file)
- Repeat Folder (current folder)
- Repeat All (all files)
- Off (cancel)
Note
For VCD with PBC on, you cannot select a repeat
mode.
Note
Actual effect to picture may vary depending on the TV.
Make selection according to your preference.
13. CLEAR button
Use CLEAR to delete the scheduled program or to cancel
input data in setting mode.
6. ANGLE button
• While playing a scene recorded with multiple angles, press
the ANGLE button.
Number changes to show the number of the current angle.
(The maximum number of possible angles is 9)
14. MEMORY button
• Press this button, the program screen is displayed as
below:
:
e.g. DVD
e.g. VCD/Audio CD
[ 1/3
ANGLE button is also used to rotate the picture in
clockwise direction during JPEG playback.
7. PAUSE/STEP button
• Press PAUSE/STEP to freeze playback.
• During still playback, press PAUSE/STEP advance the
picture frame by frame.
10
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
Chapter number
Title number
[- -]
Clear
Clear
Note
This function can only be used for discs on which scenes shot
from multiple angles have been recorded. If only one angle
is recorded, “
” will be displayed.
[- -]
Track number
• Select the items in the order you want by pressing the
number buttons.
Each time you press the / / / button, the space
is highlighted in turn. Highlight where you want to enter,
then press the corresponding number buttons.
Notes
• Some discs may not permit memory playback
operation.
• If you select repeat during memory playback, the DVD
player repeats the current memory playback.
• The programmed selections will be cleared when you
open the disc tray or turn off the DVD player.
15.SETUP button
Access the on-screen Setup menu for settings
adjustment.
16.PROGRESSIVE button
Press to change the output signal for better picture
quality 14 .
17.DVD button
Press to select the DVD mode if it is in the SD mode.
18.SEARCH (T) button
• Press SEARCH (T) and use / to move the cursor
to the title (TT) / chapter (CH) / track (TRK) / time.
e.g.
DVD TT
CH
DVD TT
CH
DVD TT
CH
VCD 2.0 TR K
CDDA
TR K
PB C
X
X
• Press the corresponding number button(s) for the title
(TT) / chapter (CH) / track (TRK) / time, then press
ENTER. Playback starts from the selected section.
Notes
• Pressing the CLEAR button resets the numbers. To
clear the display, press the SEARCH (T) button several
times.
• For VCD with PBC on, accessing tracks using number
buttons does not work.
19.MUTE button
Press to mute and restore the sound.
20.SLOW button
Forward slow playback.
Each time you press the SLOW button, the slow-motion
speed changes in the following sequence:
1/4
1/8
Play
Note
The sound is muted during slow-motion playback.
21.SUBTITLE button
For DVD discs, press this button to change the language
of the subtitle.
To turn off the subtitle, press the SUBTITLE button
repeatedly until the .... : [ off is displayed.
Notes
• Some DVDs are set to display subtitles automatically,
and you cannot turn them off even if you set the subtitle
function to off.
• During some scenes, the subtitles may not appear
immediately after you select your desired.
• Some DVDs will allow you to make subtitle selections
and turn subtitles on or off only via the disc menu.
22.AUDIO button
For DVDs, press the AUDIO button to toggle between
different audio modes. The selected audio mode will be
displayed on the screen.
For VIDEO CDs, press the AUDIO button repeatedly
during playback to hear a different audio channel (Stereo,
Left, Right or MIX).
Notes
• When you turn on the DVD player or replace a disc,
player returns to the initial default setting.
• If you select a sound track which is not included on
the disc, the DVD player plays a prior soundtrack
programmed on the disc.
• Some discs allow you to change audio selections only
via the disc menu. If this is the case, press the MENU
button and choose the appropriate language from the
selections on the disc menu.
23.PLAY button
• Press to start playback.
• The function is the same as the PLAY button on the
front panel.
24.STOP button
• Press once to stop playback and the DVD player
memorizes the location where playback is stopped.
• Press twice to clear the last playback position.
• The function is the same as the STOP button on the
front panel.
25.ENTER button
Press to confirm selections on a menu screen.
11
Introduction
To change the programmed selections, use
/ / / to move the highlighted bar to the item
you want to change and press CLEAR, then input
the new number.
• Press / / / to move the highlighted bar to
,
then press PLAY or ENTER to start playback.
• To resume normal playback from memory playback,
use / / / to move the highlighted bar to “Clear”,
then press ENTER. All the input programs will be
cleared.
Press PLAY button to resume normal playback.
Introduction
26.DISPLAY button
Press to view the operational status.
DVD Information display
e.g.
CD Information display
e.g.
Track
1) Press DISPLAY while a disc is playing, the first banner
shows the title, chapter information and the elapsed
time display of the current chapter.
2) Press DISPLAY again for Audio language, Subtitles and
Camera angle information.
3) Press DISPLAY a third time for the remaining time
display of the current chapter.
4) Press DISPLAY a fourth time for the elapsed time
display of the current chapter.
5) Press DISPLAY a fifth time for the remaining time
display of the current title.
6) To turn off the display, press DISPLAY again.
Title
Elapsed time of the
current chapter
Chapter
DVD TT
CH
Audio language
D
1/3 ENG
Title
DVD TT
Camera angle
Subtitles
6CH
1/1
ENG
Remaining time of the
current chapter
Chapter
CH
Title
DVD TT
Elapsed time of the
current title
Chapter
CH
Title
DVD TT
Remaining time of the
current title
Chapter
CH
VCD Information display
e.g.
1) Press DISPLAY while a disc is playing, the first banner
shows the track, play mode information and the elapsed
time display of the current track.
2) Press DISPLAY again for the remaining time display of
the current track.
3) Press DISPLAY a third time for the elapsed time display
of the played tracks.
4) Press DISPLAY a fourth time for the remaining time
display of the disc.
5) To turn off the display, press DISPLAY again.
Track
VCD 2.0 TR K
Track
VCD 2.0 TR K
Track
VCD 2.0 TR K
Track
VCD 2.0 TR K
Repeat Off
PB C
X
Repeat Off
PB C
Elapsed time of the
played track
X
Remaining time of the
current disc
40
Note
“PBC” display will change from light green to black when
PBC is set to Off.
12
CDDA
Remaining time of the
current track
X
Repeat Off
Elapsed time of the
played track
X
TR K
Track
CDDA
Repeat Off
TR K
Track
CDDA
X
TR K
Track
Elapsed time of the
current track
Repeat Off
TR K
Remaining time of the
current disc
X
40
27.MENU button
Display the menu of DVD.
28.NAVI button (DVD/VCD)
Press to display and access features and settings.
29.RETURN button
Press to return to previous menu or exit the menu.
For VCD 2.0, PBC must be on in order to return to the
menu when RETURN is pressed.
30.PBC button
Press to toggle between PBC On and PBC Off.
31. A-B RPT button
Set the beginning and end points of a section to repeat.
Notes
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment
that includes multiple camera angles.
• You can specify a segment only within the current title
or track (VIDEO CD).
• There may be a slight difference between point A
and the location where playback actually resumes
depending on the disc.
32. ZOOM button
Press to zoom in the current picture.
Notes
• During some scenes, the buttons may not work as
described.
• Zooming does not work on subtitles or menus included
on DVDs.
33. HDMI button
Press HDMI to receive a suitable video quality
14
.
The function is the same as the HDMI SELECT on the
front panel.
34. SD button
Select the SD mode if a SD card is inserted.
X
Repeat Off
PB C
Remaining time of the
current track
X
Repeat Off
PB C
Elapsed time of the
current track
CDDA
Repeat Off
Connecting to a TV
Connect the DVD player to your TV.
Connecting to a TV
PB
Connections
Y
VIDEO
PR
VIDEO OUT
Normal TV
HDMI OUT
AUDIO
OUT
R
ANALOG
L
COAXIAL DIGITAL
To VIDEO
OUT
(yellow)
To 2ch AUDIO OUT
(R: red, L:white)
• Make the following setting.
To audio
input
To video
input
(yellow)
Select:
Page
“Off”,
“PCM” or
“Raw”
22
Component
P-Scan
HDMI
22
On-screen display
Audio/Video cables (supplied)
“Digital out”
“Video”
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before making
any connections.
• If your television set has one audio input, connect the left and right audio outputs of the DVD player to a Y cable adapter (not supplied)
and then connect to your TV.
• Connect the DVD player directly to your TV. If you connect the DVD player to a VCR, TV/VCR combination or video selector, the playback
picture may be distorted as DVDs are copy protected.
• Analog audio out will not have sound if DTS playback is selected.
Connecting to a TV (Using the component video jacks)
Interlaced outputs (ColorStream®)
Progressive outputs (ColorStream Pro®)
Some TVs or monitors are equipped with component video inputs.
Connecting to these inputs allows you to enjoy higher quality picture
playback.
Actual labels for component video inputs may vary depending on the
TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)
In some TVs or monitors, the color levels of the playback picture may
be reduced slightly or the tint may change. In such a case, adjust the
TV or monitor for optimum performance.
Some TVs or monitors are equipped with component video inputs
that are capable of reproducing a progressively scanned video signal.
Connecting to these inputs allows you to view the highest quality
pictures with less flicker.
Consumers should note that not all high definition television sets
are fully compatible with this product and may cause artifacts to
be displayed in the picture. In case of 480 progressive scan picture
problems, it is recommended that the user switch the connection to
the “standard definition” output. If there are questions regarding our
TV set compatibility with this model 480p DVD player, please contact
our Customer Service Center.
To Y video
input
To PB video
input
Y
VIDEO
PB
PR
VIDEO OUT
To PR video
input
To audio input
HDMI OUT
AUDIO
OUT
R
ANALOG
L
COAXIAL DIGITAL
To 2ch AUDIO OUT
(R: red, L:white)
Audio cable (not supplied)
Component video cable (not supplied)
13
Connections
• Make the following setting.
Switching the output signal (interlaced / progressive)
using the remote control
On-screen display
Select:
Page
You can temporarily switch the output signal for better picture
“PCM” or
quality. Press PROGRESSIVE button repeatedly on the remote
22
“Digital out”
“Raw”
control to select Video out to P-Scan or HDMI mode.
If your TV does not support the progressive scan format, the
Component
“Video”
*P-Scan
22
picture will appear scrambled or blank. To return to normal picture,
(Progressive)
press PROGRESSIVE button repeatedly to turn off progressive/
HDMI mode. Sometimes it can take awhile before the correct
* Only for TV equipped with component video
mode is displayed.
input jacks which support the progressive
scan.
Notes
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet
before making any connections.
• If you place the DVD player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD player away
from the tuner and radio.
• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level.
Otherwise, high volume sound may damage your hearing as well as the speakers.
• Turn off the amplifier before you connect or disconnect the DVD player’s power cord. If you leave the amplifier power on, the speakers
may be damaged.
• Analog audio out will not have sound if DTS playback is selected.
• ColorStream® and ColorStream Pro® are registered trademarks of Toshiba America Consumer Products L.L.C.
Connecting to a display (Using a HDMITM cable)
Y
VIDEO
PB
PR
VIDEO OUT
HDMI OUT
AUDIO
OUT
R
ANALOG
L
COAXIAL DIGITAL
To HDMI
Output
Available output signals are below:
• Auto
• 480p (progressive)
• 720p (progressive)
• 1080i (interlaced)
• 1080p (progressive)
HDMI Cable
(not supplied)
HDMI-compatible display
• Make the following setting.
Switching the video quality (HDMI mode) using HDMI
button on the remote control or HDMI SELECT button on
the front panel.
Press HDMI button on the remote control or HDMI SELECT
button on the front panel to receive a suitable video quality. The
video quality is required to match your TV having HDMI feature
and suitable quality. Please also check your TV owner’s manual.
Press this button to change the output signals as below. See the
About HDMI
HDMI indicator and select the appropriate output signal.
HDMI indicator
Video output signal
illuminates “ • 1080p ”
Press
illuminates “ • 1080i ”
Press
1080p (progressive)
illuminates “ • 720p ”
Press
illuminates “ • 480p ”
Press
illuminates “• 480p, • 720p,
• 1080i, • 1080p”
Press
720p (progressive)
1080i (interlaced)
480p (progressive)
Auto
On-screen display
Select:
Page
“Digital out”
“PCM”
22
“Video”
HDMI
22
HDMI (High Definition Multimedia Interface) supports both video
and audio on a single digital connection for use with DVD players,
DTV, set-top boxes, and other AV devices. HDMI was developed
to provide the technologies of High Bandwidth Digital Content
Protection (HDCP) as well as Digital Visual Interface (DVI) in one
specification. HDCP is used to protect digital content transmitted
and received by DVI-compliant or HDMI-compliant displays.
HDMI has the capability to support standard, enhanced, or highdefinition video plus standard to multi-channel surround-sound
audio. HDMI features included uncompressed digital video, a
bandwidth of up to 2.2 gigabytes per second (with HDTV) signals,
one connector (instead of several cables and connectors), and
communication between the AV source and AV devices such
as DTVs.
480p, 720p, 1080i and 1080p are signals created with this DVD HDMI, the HDMI logo and High-Definition Multimedia Interface
Player from original 480i signal. The resolution of the picture may are trademarks or registered trademarks of HDMI licensing
LLC.
not be increased even if they are selected.
14
Content of the output for each output jack is shown in the following table and differ depending on the On-Screen Display Setting:
Content of output for each output jack
HDMI
Video
Component
Output
Output
Output
-
Composite
480i
-
Composite
480p
480p
720p
1080i
1080p
Composite
Composite
Composite
Composite
480i
480i
480i
480i
* Settings for HDMI output format are performed using the HDMI button on the remote control or HDMI SELECT button on the
front panel.
Notes
• If Auto is selected, it follows preference HDMI aspect ratio of TV.
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
• If you have a HDMI (with HDCP) equipped monitor or display, you can connect it to this player using a HDMI cable.
• The HDMI connector outputs uncompressed digital video, as well as almost every kind of digital audio that the player is compatible
with, including DVD-Video, Video CD/Super VCD, CD and MP3.
• This unit has been designed to be compliant with HDMI (High Definition Multimedia Interface) depending on the component
you have connected. Using a HDMI connection may result in unreliable signal transfers.
• Because HDMI is an evolving technology, it is possible that some devices with an HDMI input may not operate properly with
this DVD player.
• When using HDMI cable, do not connect to other analog video outputs.
• No sound will be output from the HDMI cable if the digital out is not set to PCM.
• HDMI output is only available when the Video output is set to “HDMI”. Otherwise the HDMI button is invalid.
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD player to optional audio equipment.
• For connection to your TV, see “Connecting to a TV” .
• This section uses the following reference marks.
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Warning
• When you are connecting (via the COAXIAL DIGITAL AUDIO
OUT jack) an AV decoder that does not have Dolby Digital,
DTS® or MPEG2 decoding function, be sure to set “Digital
Output” to “PCM” from the on-screen displays. Otherwise,
high volume sound may damage your hearing as well as the
speakers.
• When playing DTS-encoded discs (DVDs and audio CDs),
excessive noise may be output from the analog audio output
jacks. To avoid possible damage to the audio system, you
should take proper precautions when the analog audio output
jacks of the DVD player are connected to an amplification
system. To enjoy DTS Digital Surround™ playback, an
external 5.1 channel DTS Digital Surround™ decoder system
must be connected to the COAXIAL DIGITAL AUDIO OUT
jack of the DVD player.
Notes
• Do NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the AC-3 RF input of a Dolby Digital Receiver.
This input on your A/V Receiver is reserved for Laser disc use only and is incompatible with the COAXIAL DIGITAL AUDIO OUT
jack of the DVD player.
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the “DIGITAL (COAXIAL)” input of a Receiver or
Processor.
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening
level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD player’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
15
Connections
On-Screen Display Setting
“Video”
HDMI Output
Setting
Setting
Component
Invalid
(Interlaced)
P-Scan
Invalid
(Progressive)
480p
720p
HDMI
1080i
1080p
Connections
Connecting to Optional Equipment (continued)
Connecting to an amplifier equipped with a Dolby® Digital decoder
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest
movies, and is now available to reproduce this realistic effect in the home. You can Manufactured under license from
Dolby Laboratories. Dolby and the
enjoy motion picture and live concert DVDs with this dynamic realistic sound by
double-D symbol are trademarks of
connecting the DVD player to a 6 channel amplifier equipped with a Dolby Digital
Dolby Laboratories.
decoder or Dolby Digital processor. If you have a Dolby Surround Pro Logic decoder,
you will obtain the full benefit of Pro Logic from the same DVD movies that provide • Use DVDs encoded via the Dolby
full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby
Digital recording system.
Surround mark.
• Make the following setting.
Amplifier equipped with a
Dolby Digital decoder
To COAXIAL
type digital
audio input
To wall
outlet
On-screen display
Select:
“Digital out”
“PCM” or
“Raw”
Page
22
To COAXIAL
DIGITAL
AUDIO OUT
75 Ω coaxial cable (not supplied)
Connecting to an amplifier equipped with Dolby Surround Pro Logic
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting • Make the following setting.
an amplifier and speaker system (right and left front speakers, a center speaker,
On-screen display
Select:
and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier
equipped with a Dolby® Digital decoder.” Refer to that amplifier’s owner’s manual
and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.
“Digital out”
“PCM” or
“Raw”
Page
22
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
* Connect one or two rear speakers.
The output sound from the rear speakers
will be monaural even if you connect two
rear speakers.
Amplifier equipped with
Dolby Surround Pro Logic
To audio
input
To wall
outlet
To ANALOG
AUDIO OUT
Audio cable (not supplied)
16
Connecting to an amplifier equipped with a DTS® decoder
Amplifier equipped with a
DTS decoder
To COAXIAL
type digital
audio input
To COAXIAL
DIGITAL
AUDIO OUT
To wall
outlet
Manufactured under license under U.S.
Patent #: 5,451,942 & other U.S. and
worldwide patents issued & pending.
DTS and the Symbol are registered
trademarks and DTS Digital Out and the
DTS logos are trademarks of DTS, Inc.
Product includes software. © DTS, Inc.
All Rights Reserved.
• Use DVDs or audio CDs encoded
via the DTS recording system.
• Make the following setting.
On-screen display
Select:
Page
“Digital out”
“Raw”
22
75 Ω coaxial cable (not supplied)
Connecting to an amplifier equipped with an MPEG2 audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVDs with dynamic realistic sound • Use DVDs encoded via the MPEG2
by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2
recording system.
audio processor.
• Make the following setting.
Amplifier equipped with an
MEPG2 audio decoder
To COAXIAL
type digital
audio input
To wall
outlet
On-screen display
Select:
“Digital out”
“PCM” or
“Raw”
Page
22
To COAXIAL
DIGITAL
AUDIO OUT
75 Ω coaxial cable (not supplied)
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an • Make the following setting.
amplifier equipped with a digital audio input and speaker system (right and left
On-screen display
Select:
front speakers).
“Digital out”
“PCM”
Page
22
Amplifier equipped with
a digital audio input
To COAXIAL
type digital
audio input
To wall
outlet
To COAXIAL
DIGITAL
AUDIO OUT
75 Ω coaxial cable (not supplied)
17
Connections
DTS®
DTS is a high quality surround technology used in theaters and now available for
home use, on DVDs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1
channel DTS encoded sound tracks on DVDs or audio CDs.
Basic playback
Playing a Disc
This section shows you the basics on how to play a disc.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
Basic playback
Preparations
• When you want to view a disc, turn on the TV and select the video input connected to the DVD player.
• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected to
the DVD player.
1
Press the ON/STANDBY button.
2
Press OPEN/CLOSE.
3
Press PLAY.
The DVD player turns on.
To pause playback (still mode)
Press PAUSE/STEP during playback.
The disc tray opens.
To resume normal playback, press the
PLAY button.
• The sound is muted during still
mode.
Place the disc on the disc tray.
With the playback
side down
• There are two different disc sizes. Place the disc in
the correct guide on the disc tray. If the disc is out
of the guide, it may damage the disc and cause the
DVD player to malfunction.
• Do not place a disc which is unplayable in this DVD
player.
4
To start playback in the stop mode
Press OPEN/CLOSE to close the disc tray.
Playback starts.
To stop playback
Press STOP.
To remove the disc
Press OPEN/CLOSE.
Remove the disc after the disc tray
opens completely.
Be sure to press the OPEN/CLOSE
button to close the disc tray after you
remove the disc.
To turn the power off
Press ON/STANDBY button to turn the unit off.
If you insert a DVD that contains a top menu, a
to select the
menu may appear. Use / / /
title you want to view, then press ENTER to start
playback.
• You may need to press the TOP MENU or MENU
button to display disc menu (depending on the actual
DVD.)
Notes
• If the disc tray is holding a disc you have already played,
playback will begin from the location where you last
stopped.
• Some video CD are recorded with PBC (Playback Control),
a menu with recorded contents may appear on the TV if
you have turned the PBC on. You can make your selection
according to its PBC menu. Press the PBC button on the
remote control to turn PBC on or off anytime during Video
CD playback. When switching from PBC off to PBC on mode,
playback will start from the beginning of the disc. To turn on
the menu display again, press the RETURN button.
18
Automatic Power Off function
If the DVD player is stopped, or the screen saver is
engaged for approximately 20 minutes, the DVD player
will automatically turn itself off.
Notes
• Do not move the DVD player during playback. Doing so may
damage the disc.
• Use the OPEN/CLOSE button to open and close the disc
tray. Do not push the disc tray while it is moving. Doing so
may cause the DVD player to malfunction.
• Do not push up on the disc tray or put any objects other than
discs on the disc tray. Doing so may cause the DVD player
to malfunction.
• In many instances, a menu screen will appear after playback
of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching
that image onto its screen. To avoid this, be sure to press
the STOP button on your remote control once the movie is
completed.
Playing MP3/JPEG Files
You can play MP3 or JPEG files that have been recorded on a CD-R or CD-RW on the DVD player.
Playing MP3/JPEG Files
1
Press OPEN/CLOSE to open the disc
tray, place a disc that contains MP3/
JPEG Files.
ENTER
: music icon
2
: picture icon
Press / to select the Music or Picture
icon, and then press ENTER.
(For example: selecting the Picture icon)
Make sure the disc you are playing contains the
music or picture files.
...[PHOTOS]123.JPG
A list of folders in the
disc appears, press
/ button to select
a folder and then
press ENTER.
e.g.
...
C0001
C0002
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
Notes
• Make sure that a disc you want to play is compatible with
this DVD player.
• Some discs may not permit this operation.
• When the MP3 file is out of the above specifications, the
song may be skipped or muted with counter moving.
• It is recommended to record the same kind of files in a
CD-R or CD-RW.
C0003
C0004
2288X1712
1
JPEG files compatibility
C0005
766KB
C0006
2009/12/01
PGUP/DN RETURN
C0007
ENTER
MENU
: selects a file.
: Page up or Page down
MENU : views a thumbnail view.
RETURN : returns to previous menu.
ENTER : plays your selected file.
This DVD player requires discs/recordings to meet certain
technical standards in order to achieve optimal playback
quality. Pre-recorded DVDs are automatically set to these
standards. There are many different types of recordable
disc formats (including CD-R containing MP3 files).
Because this area of technology is still evolving, Toshiba
cannot guarantee that all recordable discs will produce
optimal playback quality. The technical criteria set forth in
this owner’s manual are meant only as a guide.
Please be advised that you must obtain permission from
the applicable copyright owners to download copyrighted
content, including music files, in any format, including the
MP3 formats, prior to the downloading thereof. Toshiba
has no right to grant and does not grant permission to
download any copyrighted content.
JPEG disc compatibility with this DVD player is limited as
follows:
• Playable discs:
CD-R (650MB / 74 min. only)
CD-RW may not be compatible.
• CD physical format: Mode 1, Mode 2 XA Form 1
• File system:
ISO9660 Level 1, 2 or Joliet
• File name:
A file name should be in alphabet
and numerals only, and must
incorporate “JPG” extension.
e.g.“********.JPG” (Do not name
the file with “JPE” or “JPEG”
extension.)
• Total number of folders: Less than 100
• Total number of files: Less than 1000
Depending on the file size, some files may not display the
entire image.
Some discs may not permit this operation. Especially, the
following conditions of included files will increase the disc’s
disability.
1. Pixels over 4000 x 4000 in height and/or width
2. File size over 16M bytes
3. File format except Exif
19
Basic playback
A selection menu
will appear on the
screen.
MP3 Playable files
MP3 disc compatibility with this player is limited as
follows:
• Playable discs:
CD-R (650MB / 74 min. only)
CD-RW may not be compatible.
• Sampling Frequency: 44.1 kHz only
• Bit rate:
32 kbps - 320 kbps (CBR*)
• CD physical format:
Mode 1, Mode 2 XA Form 1
• File system:
ISO9660 Level 1, 2 or Joliet
• File name:
A file name should be in alphabet
and numerals only, and must
incorporate “MP3” extension.
e.g. “********.MP3”.
• Total number of folders: Less than 100
• Total number of files: Less than 1000
* CBR = Constant Bit Rate
Basic playback
Zooming in an image
Viewing a thumbnail view
Press ZOOM repeatedly to toggle through Q1, Q2 and
Q3.
To return to normal playback, press ZOOM until the
Q:Off appears.
Press MENU in the photo list screen
e.g.
Press the / / /
buttons to view a different part
of the image. You may move the image from the centre
position to up, down, left and right direction. When you
reach the edge of the image, the display will not shift
anymore in that direction.
Rotating an image
Press the ANGLE button repeatedly. The image will rotate
in the clockwise direction as follows:
19
C0001 [784k]
C0002 [704k]
C0003 [684k]
C0004 [584k]
C0005 [804k]
C0006 [484k]
.
1. Press the / / / to select an image, press the
ENTER button to view one image in full-screen.
2. Press SKIP
/
to view other thumbnail screen.
Slide Show playback
The Slide Show enables you to view picture (files) one
after another automatically.
• Set “JPEG Interval” setting to “5 seconds”, “10 seconds” or
“15 seconds” 22 .
Using a SD/SDHC card
This unit supports the use of a Secure Digital (SD)/High Capacity SD (SDHC) Memory Card (not included).
You can enjoy playing back MP3/JPEG files stored in the card.
Inserting a SD/SDHC card
1
Inserting a SD/SDHC card fully into the
slot on the front of DVD player until it
clicks as illustrated.
To pause playback
Press PAUSE/STEP during playback
To resume normal playback, press
PLAY.
To stop playback
Press STOP.
SD/SDHC
card
2
Press the SD button on the remote
control to select SD mode.
A selection menu will appear on the screen if it
contains music and picture files in the SD/SDHC
card.
ENTER
3
20
Press
/
to select the Music or
Picture icon, and then press ENTER.
(please see 19 for details.)
To return to DVD mode
DVD
• Pressing the DVD button on the remote
control to resume DVD playback during
SD/SDHC stop.
Removing the SD/SDHC card
In stop mode, gently push the SD/SDHC card into the slot
and then pull it out slowly.
Notes
• If you cannot easily insert the memory card, you may
have inserted it incorrectly. Try to turnover the card and
then insert again. Do not force the memory card into the
memory card slot.
• Do not remove the SD/SDHC card during playback.
• The connection may not be available depending on the
type of your SD/SDHC card.
This unit is compatible with the following Memory
Devices:
• Secure Digital™ (SD) Memory Card (16MB - 2GB, FAT16)
• SDHC Memory Card (4GB - 32GB, FAT32)
- This unit does not support NTFS file system.
- Supported JPEG file size: less than 16M bytes
Customizing the Function Settings
You can change the default settings to customize performance to your preference.
Using the Language setup menu
1. Press SETUP during stop, the system setup menu
appears.
2. Press / button to select the setting item: Language,
Subtitle, Audio or DVD Menu.
/
button to select the
3. Press button, then use
setting choice on the right.
4. Press ENTER button.
5. Press SETUP button to exit the menu.
Using the Video setup menu
1. Press SETUP during stop.
2. Press button to select Video.
3. Press / button to select the setting item: Aspect Ratio,
Video, HDMI Res. or JPEG Interval.
4. Press button, then use / button to select the setting
choice on the right.
5. Press ENTER button.
6. Press SETUP button to exit the menu.
Video
Language
Subtitle
Audio
DVD Menu
Aspect Ratio
Video
HDMI Res.
JPEG Interval
Aspect Ratio
Language
To select a preferred language for on-screen displays.
English: To view on-screen displays in English.
Français: To view on-screen displays in French.
Español: To view on-screen displays in Spanish.
Subtitle/Audio/DVD Menu
DVD
These menus contain various language options for Subtitle,
Audio and Menu which may be recorded on the DVD.
Notes
• Some DVDs may not be played in a different language
than you selected. A prior language may be programmed
on the disc.
• Some DVDs may be set to display subtitles in a different
language other than you selected. A prior subtitle
language may be programmed on the disc.
• Some DVDs allow you to change subtitle selections only
via the disc menu. If this is the case, press the MENU
button and choose the appropriate subtitle language from
the selection on the disc menu.
• Some DVDs may not include your pre-selected language.
In this case, the DVD player automatically displays
disc menus consistent with the disc’s initial language
setting.
Function setup
Language
DVD
Depending on the format of the DVD disc, you can choose
the picture format (aspect ratio) best suited to the format
of your TV screen.
4:3 LB : Select when a standard 4:3 TV
is connected.
When wide-screen video is played
in this mode on a conventional
screen, black bands appear
at the top and bottom of the
screen.
4:3 PS : Select when a standard 4:3 TV
is connected.
Displays pictures cropped to fill
your TV screen. Either or both
sides of the picture are cut off.
16 : 9 : Select when a 16:9 TV is
connected. For playing widescreen videos on a wide-screen
TV.
Notes
• The displayable picture size is preset on the DVD.
Therefore, the playback picture of some DVDs may not
conform to the picture size you select.
• When you play DVDs recorded in the 4:3 picture size only,
and you own a 16:9 TV set, Video output picture will be
16:9 only when you select the TV picture setting on the
TV.
• If you select “16:9” and you own a 4:3 TV set, the DVD
playback picture will be horizontally distorted during
playback. Images will appear to be horizontally compressed.
Always be sure that your TV shape conforms to the actual
TV in use.
21
Function setup
Customizing the Function Settings (continued)
Video
Digital out
The video output of the DVD player can be selected as
Component, P-Scan or HDMI.
Selects the output sound format corresponding to your
system connection.
Component: Select if you connect the DVD player to your
TV which has component video inputs.
P-Scan:
Select if you connect the DVD player to your
TV which has component video inputs that
support progressive scan.
HDMI:
High Definition Multimedia Interface. Select if
you connect the DVD player to TV via HDMI
input.
Note
For the HDMI output, please connect the unit to your TV
via HDMI cable 14 .
Off: To disable Digital out.
Raw: Disc audio raw data will be output. Select “Raw” if
your amplifier supports “DTS”.
HDMI Res. (Resolution)
You can set the HDMI Res. (Resolution) to be Auto, 480p,
720p, 1080i or 1080p according to the connected TV.
Notes
• Select the HDMI resolution according to the performance
of the connected TV.
• If the Video out is not set to “HDMI”, you cannot select
the “HDMI Res.”.
JPEG Interval
To set the JPEG Interval for slide show playback. Select
“Off” to disable the slide show feature.
5 seconds: Plays back images in the form of a slide show
at 5 seconds interval.
PCM: Select when connected to a Multi-channel digital
stereo amplifier. The DVD player outputs sound in the
PCM stereo format when you play a DVD recorded
on the Dolby Digital, MPEG1 or MPEG2 recording
system.
Night Mode
DVD
Night mode is equivalent to Dynamic Range Compress.
When it is On, it reduces the variations between loud and
soft sounds in audio output. You can still hear softer sounds
and dialog even in very low volume.
Note
Night mode is Dynamic Range Control (DRC) option for
analog audio output.
Using the Rating setup menu
1. Press SETUP during stop.
2. Press button to select Rating.
3. Press / button to select the setting option: Password or
Rating.
10 seconds: Plays back images in the form of a slide show
at 10 seconds interval.
15 seconds: Plays back images in the form of a slide show
at 15 seconds interval.
Rating
Password
Rating
Using the Audio setup menu
1. Press SETUP during stop.
2. Press button to select Audio.
3. Press / button to select the setting item: Digital out
or Night Mode.
4. Press button, then use / button to select the
setting choice on the right.
5. Press ENTER button.
6. Press SETUP button to exit the menu.
Audio
Digital out
Night Mode
Password
DVD
Press
/ button to select the Password option, then press
button. Enter your 4-digit security code and then press the
ENTER button.
If you forget the password, you can erase your current
password by pressing number button 8 on the remote
control four times, then press ENTER button to confirm
the setting. (PASSWORD: 8888)
The Parental lock
is active.
22
The Parental lock is
NOT active.
Rating
DVD
DVDs equipped with the password function are rated
according to their content. The contents allowed by a
parental lock level and the way a DVD can be controlled
may vary from disc to disc.
For example, if the disc allowed, you could edit out violent
scenes unsuitable for children and replace them with more
suitable scenes, or you could lock out playback of the disc
altogether.
1) Press / button to select the Rating option, then press
button.
2) Press / button to select parental lock level and then
press the ENTER button.
3) Press / button to select the Password option, then
press button. Enter your 4-digit security code and then
press the ENTER button.
If you forget your password at this moment, you
cannot use the super password (8888). You need to
go to the Rating setup menu to reset and input a new
password.
The parental lock levels are equivalent to the following
ratings.
Level 1 : Kid Safe Level 5 : PG-R
Level 2 : G
Level 6 : R
Level 3 : PG
Level 7 : NC-17
Level 4 : PG-13
Level 8 : Adult
• DVDs may or may not respond to the parental lock
settings. This is not a defect in the DVD player. Make
sure this function works with your DVDs.
• Rating level cannot be changed when the Parental lock
is active.
Using the TV System setup menu
1. Press SETUP during stop.
2. Press button to select TV System.
3. Press / button to select the setting item: Default,
Screen Saver or HDMI CEC.
4. Press button, then use / button to select the
setting choice on the right.
5. Press ENTER button.
6. Press SETUP button to exit the menu.
TV System
Note
When you reset the DVD player to the factory default, the
DVD player will take 3-5 seconds to reset.
Screen Saver
To turn on or off the screen saver (screen protection to
prevent image burn).
Note
When you leave the unit in DVD stop mode for approximately
2 minutes, the screen saver of the DVD player automatically
appears if you set the Screen Saver to On mode. To turn
off the screen saver, press the PLAY button.
HDMI-CEC: REGZA-LINK®
You can control this DVD unit from TV’s remote which is
connected via HDMI cable.
Functions available for the HDMI-CEC
• One touch play
When the operations with following button of this unit’s
remote control are performed, the TV will automatically
switch to appropriate input channel.
Button for one touch play: [PLAY] (make sure a disc is
inserted.)
• System information
Get & Set Menu Language:
This unit recognizes the OSD languages set for the TV
and automatically set the same language as the player
menu language (OSD menu language) for this unit.
Power off:
When you turn the TV off, this unit will automatically turn
off.
Receiving operational signal from TV’s Remote:
You can operate this unit with TV’s remote control. Check
your TV owner’s manual for details.
Notes
• This function may not work properly depending on the
TV you are connecting.
• If the Video out is not set to “HDMI”, HDMI-CEC will not
work.
• Other components must be compatible with HDMI-CEC
in order to use this function.
Default
Screen Saver
HDMI CEC
REGZA-LINK is a registered trademark of Toshiba
Corporation.
23
Function setup
You cannot play DVD discs rated higher than the level
you selected unless you cancel the parental lock
function and enter the 4-digit security code. Then
press ENTER to confirm the password.
Default
This option allows you to return the unit’s setting to the
factory default. Any changes you have made to the unit’s
settings will be reverted back to the original setting except
your password and rating level.
Others
Before Calling Service Personnel
Check the following guide for the possible cause of a problem before contacting service.
Symptoms and correction
Cause
Correction
No power.
Symptom
• The power plug is disconnected.
• Connect the power plug securely into the wall outlet.
The DVD player turned off
by itself.
• The automatic power off function turned the
unit off.
• Press the PLAY button.
18
No picture or abnormal color
(pinkish, greenish, etc.).
• The TV is not set to receive DVD signal
output.
• Select the appropriate video input mode on the TV
so the picture from the DVD player appears on the
TV screen.
18
• The video/HDMI cable is not connected
securely.
• Connect the video/HDMI cable securely into the
appropriate jacks.
13-14
• Mismatch setting between TV and this unit.
• Select the correct Video out setting.
• Wrong connection.
• Check the connection.
• PROGRESSIVE button is pressed on a TV
equipped with component video input jacks
but does not support progressive scan.
• Toggle PROGRESSIVE button to turn off
progressive mode.
14
• The equipment connected with the audio cable
is not set to receive DVD signal output.
• Select the correct input mode of the audio receiver
so you can listen to the sound from the DVD player.
18
• The audio cable is not connected securely.
• Connect the audio cable securely into the
appropriate jacks.
13-17
• The audio receiver or TV is turned off.
• Turn on the equipment connected with the audio
cable.
18
• The setting of output sound format is
incorrect.
• Select the proper audio setting.
22
The playback picture has occasional distortion.
• The disc is dirty.
• Remove the disc and clean it.
4
• It is in fast forward or fast reverse playback.
• Sometimes a small amount of picture distortion
may appear. This is not a malfunction.
-
Brightness is unstable or
noises are present in the
playback pictures.
• The effect of copy protection.
• Connect the DVD player directly to the TV. Avoid
connecting the DVD player to a VCR or TV/VCR
combination.
13
The DVD player does not
start playback.
• No disc is inserted.
• Insert a disc.
18
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc type and
color system.)
• The disc is placed upside down.
• Place the disc with the playback side down.
18
• The disc is not placed within the guide.
• Place the disc correctly inside the guide on the
disc tray.
18
• The disc is dirty.
• Clean the disc.
4
Playback does not follow
the course of the disc’s
program.
• It is in the mode of repeat playback, memory
playback, etc.
• These operations may prevent a proper progress
of the contents.
-
Buttons do not work.
• Power supply fluctuations or other abnormalities
such as static electricity may interrupt correct
operations.
• Press and hold the ON/STANDBY button on the
front panel for more than about 3 seconds. The
DVD player turns off. Press the button again to turn
it on. If the buttons still do not work, disconnect
the power plug and insert it into the wall outlet
again.
-
The remote control does not
work properly.
• The remote control is not pointed at the remote
sensor of the DVD player.
• Point the remote control at the remote sensor of
the DVD player.
8
• The remote control is too far from the DVD
player.
• Operate the remote control within about 7 m.
8
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
8
No sound.
24
Page
13-14
22
13-14
5
Others
Specifications
DVD player / outputs / supplied accessories
DVD Player
Power supply
120 V AC, 60 Hz
Power consumption
6 W (standby: less than 1.0W)
Mass
1.27 kg
External dimensions
430 x 42 x 209 mm (W/H/D)
Signal system
NTSC
Laser
Semiconductor laser, wavelength 650/780 nm
Frequency range
DVD linear sound : 48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
Signal-to-noise ratio
More than 93 dB
Audio dynamic range
More than 80 dB
Harmonic distortion
Less than 0.05 %
Wow and flutter
Below measurable level (less than ±0.001 % (W.PEAK))
Operating conditions
Temperature: 5 °C to 35 °C, Operation status: Horizontal
Others
Outputs
Video output
1.0 V (p-p), 75 Ω, pin jack x 1
Component video output
(Y) 1.0 V (p-p), 75 Ω, pin jack x 1
(PB)/(PR) 0.7 V (p-p), 75 Ω, pin jack x 2
Audio output (COAXIAL DIGITAL)
0.5V (p-p), 75 Ω, pin jack x 1
Audio output (ANALOG)
2.0 V (rms), 680 Ω, pin jacks (L, R) x 1
HDMI output
19 pin
Supplied Accessories
Audio/video cable ...................................................1
Remote control (SE-R0373) ..................................1
Batteries (R03/AAA) ...............................................2
• This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added in the future.
25
Others
Limited United States Warranty
Digital Audio Video (“DAV”) Product - Exchange Warranty
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original consumers in the United
States.
THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING
THIS DAV PRODUCT AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR
TRANSFEREE.
DAV PRODUCTS PURCHASED IN THE U.S.A. AND USED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT
LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.
DAV PRODUCTS PURCHASED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND
MEXICO, AND USED IN THE U.S.A., ARE NOT COVERED BY THESE WARRANTIES.
Limited Warranty
TACP warrants this DAV Product and its parts against defects
in materials or workmanship for a period of ninety (90) days
after the date of original retail purchase.
DURING THIS PERIOD, TACP WILL EXCHANGE A
D E F E C T I V E DAV P RO D U C T W I T H A N E W O R
REFURBISHED DAV PRODUCT WITHOUT CHARGE TO
YOU. DURING THE PERIOD THAT COMMENCES ON THE
DATE THAT IS NINETY ONE (91) DAYS AFTER THE DATE
OF ORIGINAL RETAIL PURCHASE AND ENDS ON THE
DATE THAT IS THREE HUNDRED SIXTY FIVE (365) DAYS
AFTER THE DATE OF ORIGINAL RETAIL PURCHASE,
TACP WILL EXCHANGE A DEFECTIVE DAV PRODUCT
WITH A NEW OR REFURBISHED DAV PRODUCT FOR
A FEE.
Rental Units
The warranty for DAV Product rental units begins on the date
of the first rental or thirty (30) days after the date of shipment
to the rental firm, whichever comes first.
Commercial Units
DAV Products sold and used for commercial purposes have a
limited warranty for all parts and labor, which warranty begins
on the date of original retail purchase and ends on the date
that is ninety (90) days thereafter.
Owner’s Manual and Product Registration Card
Read this owner’s manual thoroughly before operating this
DAV Product. Complete and mail the enclosed product
registration card or register your DAV Product on-line at www.
tacp.toshiba.com/service as soon as possible. By registering
your DAV Product you will enable TACP to bring you new
products specifically designed to meet your needs and help
us to contact you in the unlikely event a safety notification is
required under the U.S. Consumer Product Safety Act. Failure
to complete and return the product registration card does not
diminish your warranty rights.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO FOLLOWING
CONDITIONS:
(1) You must retain your bill of sale or provide other proof of
purchase.
(2) All warranty servicing of this DAV Product must be made
pursuant to the TACP DAV Product Warranty Exchange
Program.
(3) The warranties from TACP are effective only if the DAV
Product is purchased and operated in the Continental U.S.A.
or Puerto Rico.
(4) Labor service charges for set installation, setup, adjustment
of customer controls, and installation or repair of antenna
systems are not covered by this warranty. Reception
problems caused by inadequate antenna systems are your
responsibility.
(5) Warranties extend only to defects in materials or workmanship
as limited above, and do not extend to any DAV Product or
parts that have been lost or discarded by you or to damage to
the DAV Product or parts caused by fires, misuse, accident,
Acts of God ( such as lightning or fluctuations in electric
26
power), improper installation, improper maintenance, or use in
violation of instructions furnished by TACP; use or malfunction
through simultaneous use of this DAV Product and connected
equipment; or to units that have been modified or had the serial
number removed, altered, defaced, or rendered illegible.
(6) This warranty does not cover Product sold AS IS or WITH ALL
FAULTS.
How to Obtain Warranty Services
If, after following all of the operating instructions in this manual
and checking the section “Before Calling Service Personnel,” you
find that service is needed:
(1) For instructions on how to obtain warranty service for
your DAV Product under the TACP DAV Product Warranty
Exchange Program, contact TACP’s Consumer Solutions
Center toll free at 1-800-631-3811.
(2) You must include the original bill of sale (or a copy of the
original bill of sale) or other proof of purchase along with
the entire DAV Product when sending the DAV Product to
the TACP Warranty Exchange Center specified by TACP’s
Consumer Solutions Center. You are responsible for all
inbound transportation and insurance charges for the DAV
Product to the TACP Warranty Exchange Center.
For additional information, visit TACP’s website: www.tacp.
toshiba.com
ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE
OF THE U.S.A., INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF
THE LIMITED WARRANTIES SET FORTH ABOVE. WITH THE
EXCEPTION OF ANY WARRANTIES IMPLIED BY THE LAW
OF ANY STATE OF THE U.S.A. AS HEREBY LIMITED, THE
FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL
OTHER WARRANTIES, GUARANTEES, AGREEMENTS, AND
OF ALL OTHER WARRANTIES, GUARANTEES, AGREEMENTS,
AND OR REPLACEMENT OF ANY PARTS. IN NO EVENT SHALL
TACP BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST PROFITS,
BUSINESS INTERRUPTION, OR MODIFICATION OR ERASURE
OF RECORDED DATA CAUSED BY USE, MISUSE OR INABILITY
TO USE THIS DAV PRODUCT).
No person, agent, distributor, dealer, or company is authorized
to change, modify, or extend the terms of these warranties in any
manner whatsoever. The time within which an action must be
commenced to enforce any obligation of TACP arising under the
warranty or under any statute or law of the United States or any
state thereof is hereby limited to ninety (90) days from the date you
discover, or should have discovered, the defect. This limitation does
not apply to implied warranties arising under state law.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM
STATE TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A.
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, WHEN AN ACTION MAY BE BROUGHT,
OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE PROVISIONS MAY
NOT APPLY TO YOU UNDER SUCH CIRCUMSTANCES.
Others
Limited Canadian Warranty
For Toshiba Brand Digital Audio/Video Products
Toshiba of Canada Limited (“TCL”) makes the following limited warranties to original consumers in Canada. THESE LIMITED
WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS TOSHIBA
BRAND DIGITAL AUDIO/VIDEO PRODUCT (the “DAV PRODUCT(S)” or “DAV Product (s)” AS A GIFT FROM THE
ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.
DAV PRODUCTS PURCHASED IN CANADA, AND USED ANYWHERE OUTSIDE OF CANADA INCLUDING, WITHOUT
LIMITATION, THE UNITED STATES AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.
DAV PRODUCTS PURCHASED ANYWHERE OUTSIDE OF CANADA, INCLUDING, WITHOUT LIMITATION, THE
UNITED STATES AND MEXICO, AND USED IN CANADA, ARE NOT COVERED BY THESE WARRANTIES.
Limited One (1) Year Warranty on Parts and
Labour
Subject to the more limited warranty if the DAV Product is
used for any commercial or business purposes as set out
below, TCL warrants the DAV Product and its parts against
material defects in materials or workmanship that result in
the DAV Product failing for a period of one (1) year after
the date of original retail purchase. DURING THIS PERIOD,
TCL WILL, AT TCL’S OPTION, REPAIR OR REPLACE A
DEFECTIVE PART WITH A NEW OR REFURBISHED PART,
WITHOUT CHARGE TO YOU FOR PARTS OR LABOUR.
YOU MUST DELIVER THE ENTIRE DAV PRODUCT TO A
TCL DAV PRODUCT AUTHORIZED SERVICE PROVIDER
(“ASP”).YOU MUST PAY FOR ALL TRANSPORTATION AND
INSURANCE CHARGES FOR THE DAV PRODUCT TO AND
FROM THE ASP.
The warranty for DAV Product rental units begins with the date
of first rental or thirty (30) days from the date of shipment to
the rental firm, whichever comes first.
Limited Warranty for Commercial Units
TCL warrants DAV Products that are used for any commercial
or business purposes as follows: all parts are warranted against
material defects in materials or workmanship that result in
the DAV Product failing for a period of ninety (90) days after
the date of original retail purchase. DURING THIS PERIOD,
TCL WILL, AT TCL’S OPTION, REPAIR OF REPLACE A
DEFECTIVE PART WITH A NEW OR REFURBISHED PART,
WITHOUT CHARGE TO YOU FOR PARTS OR LABOUR.
YOU MUST DELIVER THE ENTIRE DAV PRODUCT TO AN
ASP. YOU MUST PAY FOR ALL TRANSPORTATION AND
INSURANCE CHARGES FOR THE DAV PRODUCT TO AND
FROM THE ASP.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE
FOLLOWING CONDITIONS:
(1) You must provide your bill of sale or other proof of
purchase.
(2) All warranty servicing of this DAV Product must be
performed by an ASP.
(3) The warranties from TCL are effective only if the DAV
Product is (i) purchased as new and unopened from TCL
or from TCL’s authorized distributors, dealers or resellers
(“ADR’s”) and (ii) located/operated in Canada.
(4) Warranties extend only to material defects in materials or
workmanship as limited above, and do not extend to:
a. Service, repairs or replacement made necessary by
accident, misuse, abuse, moisture, liquids, dust, dirt,
neglect, accedent, damage, 24/7 applications, improper
c.
d.
e.
f.
g.
h.
i.
j.
Disclaimer and Limitation of Remedy
TO THE EXTENT NOT PRECLUDED BY LAW, ALL OTHER
EXPRESS AND IMPLIED WARRANTIES, CONDITIONS
AND REPRESENTATIONS FOR THIS DAV PRODUCT,
INCLUDING THE IMPLIED WARRANTIES AND CONDITIONS
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE HEREBY DISCLAIMED AND EXCLUDED.
IF THE APPLICABLE LAW, STATUTORY OR OTHERWISE,
PRECLUDES THE EXCLUSION OF ANY IMPLIED
WARRANTIES, CONDITIONS AND REPRESENTATIONS
THEN SUCH IMPLIED WARRANTIES, CONDITIONS AND
REPRESENTATIONS ARE OTHERWISE LIMITED IN
DURATION TO THE TEAM OF THIS EXPRESS WRITTEN
LIMITED WARRANTY. TO THE EXTENT NOT PRECLUDED
BY LAW, STATUTORY OR OTHERWISE, THIS WRITTEN
WARRANTY SUPERCEDES AND SPECIFICALLY DISCLAIMS
ANY OTHER WARRANTY, CONDITION OR REPRESENTATION
NOT STATED IN THIS WARRANTY, WHETHER MADE BY
TCL, TOSHIBA CORPORATION, THEIR AFFILIATES, ADRs
AND ASPs AND WHETHER MADE ORALLY OR IN WRITING
(INCLUDING ANY STATEMENT IN ANY BROCHURE, PRESS
RELEASE, ANNOUNCEMENT, ADVERTISEMENT, POINT OF
SALE DISPLAY, ETC.).
27
Others
Rental Units
b.
installation, improper operation, improper cleaning,
improper maintenance, normal wear and tear, or any other
external cause or event, act or omission outside the control
of TCL, including fire, theft, acts of God, alteration, power
failures, power surges or power shortages, lightning, other
electrical faults, or repairs, modifications or replacements
by persons other than those authorized by TCL to service
the DAV Product;
Replacement of missing, discarded or lost parts, the
provision of retrofits, or preventive maintenance;
Repair of damage that is cosmetic only or does not affect
the DAV Product functionality, such as wear and tear,
scratches and dents;
Service on Toshiba-branded accessory items (such
accessory items may be covered by their own warranty);
Service on third party products or service made necessary
by use of incompatible third party products;
Service made necessary by the simultaneous use of this
DAV Product and connected equipment;
Modifications to the DAV Product not approved in writing
by TCL, and service made necessary by the use or
installation of non-Toshiba modifications to the DAV
Product;
Service of a DAV Product on which the TOSHIBA label or
logo, rating label or serial number have been defaced or
removed;
On-site service and repair of the DAV Product;
Damage to the DAV Product caused by failure to follow
the specifications, User manuals or guides as to usage
and/or storage.
Others
YOU MUST READ AND FOLLOW ALL SET-UP AND USAGE
INSTRUCTIONS IN THE APPLICABLE USER GUIDES AND/
OR MANUALS. IF YOU FAIL TO DO SO, THIS DAV PRODUCT
MAY NOT FUNCTION PROPERLY AND YOU MAY SUFFER
DAMAGE. THIS WARRANTY WILL NOT COVER ANY SERVICE
THAT IS REQUIRED, IN PART OR IN WHOLE, AS A RESULT
OF ANY FAILURE TO FOLLOW THE SET-UP AND USAGE
INSTRUCTIONS. THIS WARRANTY DOES NOT APPLY
AND SHALL BE VOID AND UNENFORCEABLE IF THE DAV
PRODUCT IS OPENED, SERVICED, OR REPAIRED BY
PERSONS OTHER THAN THOSE AUTHORIZED BY TCL TO
SERVICE OR REPAIR THE DAV PRODUCT.
IF THE DAV PRODUCT FAILS TO WORK AS WARRANTED
ABOVE, YOUR SOLE AND EXCLUSIVE REMEDY SHALL
BE REPAIR OR REPLACEMENT OF THE DEFECTIVE
PART. IN NO EVENT WILL TCL, TOSHIBA CORPORATION,
THEIR AFFILIATES, ADRs OR ASPs (THE “RELATED
PARTIES”) BE LIABLE TO YOU OR ANY THIRD PARTY FOR
ANY DAMAGES. MONEY, REIMBURSEMENT, COSTS OR
EXPENSES. THIS LIMITATION APPLIES TO DAMAGES,
MONEY, REIMBURSEMENT, COSTS OR EXPENSES OF ANY
KIND WHATSOEVER INCLUDING ANY DIRECT OR INDIRECT
DAMAGES, DAMAGE TO PROPERTY OR PERSON, LOST
PROFITS, LOST SAVINGS, INCONVENIENCE OR OTHER
SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL
DAMAGES, WHETHER FOR BREACH OF WARRANTY,
BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE),
UNDER A STATUTE OR UNDER ANY OTHER LAW OR FORM
OR ACTION, OR WHETHER ARISING OUT OF THE USE OF
OR INABILITY TO USE THE DAV PRODUCT, EVEN IF ANY
OF THE RELATED PARTIES HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY
ANY OTHER PARTY.
No person, agent, distributor, dealer or company is authorized
to change, modify or extend the terms of these warranties in any
manner whatsoever.
Arbitration and Dispute Resolution
To the extent not precluded by law, any claim, dispute, controversy
or disagreement (whether for breach of warranty, breach of
contract, tort (including negligence), under a statute or under any
other law or form of action) against any of the Related Parties
arising out of , or otherwise relating to: (i) this warranty; (ii) the
DAV Product; (iii) any oral or written representations, statements,
brochures, press releases, advertising, announcement, point of
sale display, or promotional material relating to the DAV Product;
(iv) the relationships that result from this warranty, (the foregoing
claims, disputes controversies and disagreements are collectively
referred to as the “Dispute”), shall be referred to any resolved by
final and binding arbitration (to the exclusion of the courts). To
the extent not precluded by law, you agree to waive any right that
you may have to commence or participate in any representative
or class proceeding against the Related Parties relating to any
Dispute. If any where applicable and to the extent not preculded
by law, you further agree to opt out of any such representative or
class proceedings. Arbitration of any Dispute will be conducted in
the forum and in the manner as agreed to between you and TCL.
Failing such agreement, the arbitration will be conducted by one
arbitrator pursuant to the laws and rules relating to arbitration
generally in force in the jurisdiction in which you reside at the time
that the Dispute arises. To the extent not precluded by law, no
claim, dispute, controversy or disagreement of any other person
may be joined or combined with any Dispute by you, without the
prior written consent of TCL.
Critical Applications
The DAV Product you have purchased is not designed for any
“critical applications.” “Critical applications” means life support
systems, medical applications, connections to implanted
medical devices, commercial transportation, nuclear facilities
or systems or any other applications where DAV Product failure
could lead to injury to persons or loss of life or catastrophic
property damage.
IF THE CUSTOMER USES THE DAV PRODUCT IN ANY
CRITICAL APPLICATION, THE CUSTOMER-AND NOT TCL,
ITS AFFILIATES, ADRs OR ASPs - ASSUME SOLE AND FULL
RESPONSIBILITY FOR SUCH USE. TCL RESERVES THE
RIGHT TO REFUSE TO SERVICE ANY DAV PRODUCT USED
IN A CRITICAL APPLICATION. TCL, ITS AFFILIATES, ADRs
and ASPs HEREBY DISCLAIM ANY AND ALL LIABILITY,
DAMAGES AND CONSEQUENCES ARISING OUT OF THE
SERVICE OR REFUSAL TO SERVICE SUCH DAV PRODUCT
AND FURTHER DISCLAIM ANY AND ALL LIABILITY,
CONSEQUENCES AND DAMAGES THAT MAY ARISE OR
RESULT FROM THE USE OF THE DAV PRODUCT IN ANY
CRITICAL APPLICATIONS.
General Provisions
If and to the extent that any provision of this limited
warranty should generally be found to be unenforceable, the
unenforceable provision shall be severed from the warrany
and deemed not to form part of the warranty. The remaining
provisions of this warranty shall be and remain valid and
enforceable. If and to the extent that any provision of this
limited warranty as it relates to any of the Related Parties is
found to be invalid or unenforceable in respect of that party
(the “Excluded Party”), the Excluded Party shall be deemed
to be severed or excluded from the provision, and the provision
shall remain valid, enforceable and applicable in respect of the
other or remaining Related Parties.
To the extent permitted by law, this limited warranty shall
be governed and construed in accordance with the laws of
Ontario.
If there is any inconsistency between this limited warranty,
on the one hand, and any statement in the packaging of
the DAV Product or in any other document enclosed with,
or used in the context of the promotion or sale of, the DAV
Product, on the other hand, the provisions of this limited
warranty shall prevail.
How to Obtain Warranty Services
If, after following all of the operating instructions in
this manual and checking the “Before Calling Service
Personnel” section, you find that service is needed:
(1) To find the nearest ASP, visit TCL’s web site at www.
toshiba.ca, or call toll free 1-800-268-3404.
(2) Present your bill of sale or other proof of purchase to
the ASP.
For additional information, visit TCL’s website: www.
toshiba.ca
811-SD7391W011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement