Detecto 8435/8435KG Pediatric Scale Owner's manual

Detecto 8435/8435KG Pediatric Scale Owner's manual
DIGITAL
Pediatric Scale
Models 8435/8435KG
Owner’s Manual
8525-M316-O1 Rev B x 8435 Owner’s
1
COPYRIGHT
All rights reserved. Reproduction or use, without expressed written permission, of editorial or
pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to
the use of the information contained herein.
DISCLAIMER
While every precaution has been taken in the preparation of this manual, the Seller assumes
no responsibility for errors or omissions. Neither is any liability assumed for damages
resulting from use of the information contained herein. All instructions and diagrams have
been checked for accuracy and ease of application; however, success and safety in working
with tools depend to a great extent upon the individual accuracy, skill and caution. For this
reason, the Seller is not able to guarantee the result of any procedure contained herein. Nor
can they assume responsibility for any damage to property or injury to persons occasioned
from the procedures. Persons engaging the procedures do so entirely at their own risk.
PROPER DISPOSAL
When this device reaches the end of its useful life, it must be properly disposed of. It must
not be disposed of as unsorted municipal waste. Within the European Union, this device
should be returned to the distributor from where it was purchased for proper disposal. This is
in accordance with EU Directive 2002/96/EC. Within North America, the device should be
disposed of in accordance with the local laws regarding the disposal of waste electrical and
electronic equipment.
It is everyone’s responsibility to help maintain the environment and to reduce
the effects of hazardous substances contained in electrical and electronic
equipment on human health. Please do your part by making certain that the
device is properly disposed of. The symbol shown to the right indicates that
this device must not be disposed of in unsorted municipal waste programs.
FCC COMPLIANCE STATEMENT
This equipment generates uses and can radiate radio frequency and if not installed and used
in accordance with the instruction manual, may cause interference to radio communications.
It has been tested and found to comply with the limits for a Class A computing device
pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide reasonable
protection against such interference when operated in a commercial environment. Operation
of this equipment in a residential area may cause interference in which case the user will be
responsible to take whatever measures necessary to correct the interference.
You may find the booklet "How to Identify and Resolve Radio TV Interference Problems"
prepared by the Federal Communications Commission helpful. It is available from the U.S.
Government Printing Office, Washington, D.C. 20402. The stock No. is 001-000-00315-4.
2
8525-M316-O1 Rev B x 8435 Owner’s
INTRODUCTION
The Detecto Model 8435/8435KG Digital Pediatric scale is ideal for use in health clinics and
medical practices for weight measurement of pediatric patients. The scale is durable, having
a sturdy enameled steel scale base, and an easy-to-clean polystyrene tray that cradles
babies securely.
This manual is provided to guide you through assembly and operation of your scale. Please
read it thoroughly before attempting to assemble or operate your scale and keep it available
for future reference.
This manual is for use with the following Digital Pediatric Scale models:
8435
8435KG
SPECIFICATIONS
Capacity ….....…..…..… Model 8435, 130 lb x 0.1 lb (Model 8435KG, 59 kg x 0.05 kg)
Tray Size ...........…..….. 22 in L x 14.7 in W x 4.5in D (56 cm L x 37 cm W x 11 cm D)
Shipping Weight …....… 33 lb (15 kg)
Scale Height ....….…..... 37.5 in (95.3 cm)
Display ….….....……..
Six-digit, seven segment, 0.7 inch (17.8 mm) high LCD
Power .........………….... Six “AA” Alkaline, Ni-Cad or NiMH batteries (not included) OR an
optional 100 to 240V AC 50/60Hz 12V DC 1A wall plug-in UL/CSA
listed AC power adapter (Cardinal part number 6800-1045).
Models are available with the AC adapter included.
Keyboard .….....…......... Membrane type with 5 keys and 4 directional arrows
Connectivity: ………….. RS232 serial port
UNPACKING INSTRUCTIONS
x
x
x
x
x
Remove scale from carton by lifting up with equal force from column and platform base.
Remove all plastic wrapping, foam fillers and cardboard material from the scale.
Place scale upside down on level, stable surface and remove all cardboard packing from
bottom of scale base.
Return scale to upright position and check for any damage incurred in shipping. If scale
has been damaged, place a claim with the carrier. Use the original carton and shipping
material to return the scale.
Remove and unpack the AC power adapter, if the scale was ordered with this option.
Serial Number _____________________
Date of Purchase ___________________
Purchased Form ___________________
PRECAUTIONS
Before using this instrument, read this
manual and pay special attention to all
"WARNING" symbols:
__________________________________
__________________________________
IMPORTANT
RETAIN THIS INFORMATION FOR FUTURE USE
8525-M316-O1 Rev B x 8435 Owner’s
ELECTRICAL
WARNING
1
SCALE ASSEMBLY
Column to Scale Base Installation
1. Insert the column onto the scale base (shown in Figure 1), ensuring that the narrow side
of the column faces the scale platform.
Column
Scale Base
Figure 1. - Insert column onto scale base
2. Using a Phillips screwdriver, install the eight screws and washers to secure the column to
the scale base as shown in Figure 2.
Figure 2. - Install eight screws and washers to secure column to scale base
2
8525-M316-O1 Rev B x 8435 Owner’s
SCALE ASSEMBLY
Indicator Installation
First, install the scale cable on the indicator. Align the scale cable connector with the jack on
the back of the indicator, then gently push the connector onto the jack. Using a small flat
blade screwdriver, tighten the screws on both sides of the scale cable connector. Refer to
Figure No. 3 for the location of the scale cable jack.
Next, install the indicator on the scale column bracket by placing the screw heads on the
back of the indicator into the large end of the slotted holes in the bracket. Pull down on the
indicator to secure it to the bracket. The spring plunger will lock the indicator to the bracket.
See Figures No. 3, 4, and 5.
Spring
Plunger
Figure No. 4
Scale
Cable
Figure No. 3
AC Power Adapter
RS232
Port
Spring
Plunger
Release
Figure No. 5
Baby Tray Installation
1. Referring to Figure No. 6, remove the 2 flat
head screws from the scale platform.
2. Place the baby tray on the scale platform and
align the holes in the tray with the holes in
the scale platform.
3. Attach baby tray to scale platform using the 2
flat head screws remove in step 1.
DO NOT OVER-TIGHTEN THE SCREWS.
4. The scale is now ready for operation.
Figure No. 6
8525-M316-O1 Rev B x 8435 Owner’s
3
AC POWER ADAPTER
To power the scale using the optional 110-240V AC 50/60 Hz 12V DC wall plug-in AC power
adapter, connect the small round plug from the AC adapter into the power jack on the back of
the indicator and then plug the AC power adapter into the proper electrical outlet. Refer to
Figure 1. On models requiring 240V AC, it is the customer’s responsibility to obtain the
correct AC power adapter plug.
BATTERY OPERATION
Batteries
The scale can use 6 "AA" size Alkaline, Ni-Cad or NiMH batteries (not included). You must
first obtain and install batteries before operations can begin. Batteries are contained in a
battery holder inside indicator. Access is via a removable panel on the back of indicator.
When using batteries, all 6 batteries must be of the same type. They must be all Alkaline,
Ni-Cad or all NiMH. In addition, DO NOT mix Ni-Cad or NiMH batteries.
IMPORTANT! The scale can be operated from Alkaline, Ni-Cad or NiMH batteries.
All six (6) batteries must be of the same type. They must all be Alkaline, all Ni-Cad
or all NiMH. DO NOT mix Alkaline and Ni-Cad or NiMH batteries.
CAUTION! The AC power adapter is also used to recharge the batteries, when the
scale is operated from Ni-Cad or NiMH batteries. DO NOT connect the AC power
adapter if using alkaline batteries. Also, when using alkaline batteries, make sure
the 0-3 setup option is disabled (set to 0). Refer to Setup and Calibration or
Setup Review sections of 750 Weight Indicator Owner’s Manual (8555-M483-O1).
Battery Status
The 750 indicator will operate for up to 250 hours on new Alkaline batteries or for up to 100
hours on fully charged Ni-Cad or NiMH batteries depending on the condition of the batteries
(from new to about 500 recharges). The battery bar graph on the display indicates the battery
capacity in 4 steps:
4 segments - the full battery capacity is available,
3 segments - the battery is at 75% of capacity,
2 segments - the battery is at 50% of capacity,
1 segment: - the battery is at 25% capacity.
When the battery voltage drops too low for accurate weighing, the indicator will show !6;
and then shut off. You will be unable to turn the indicator back on until the Alkaline batteries
have been replaced or if using Ni-Cad or NiMH batteries, the AC power adapter is connected
to the display to operate it and recharge the batteries.
Battery Charging
To recharge the Ni-Cad or NiMH batteries, the AC power adapter must be connected to a
power outlet and plugged into the indicator. It will take approximately 8 to 10 hours to fully
recharge the batteries in the display. Charging the batteries for more than 10 hours will not
damage them. NOTE: The indicator may be operated while the batteries are charging.
4
8525-M316-O1 Rev B x 8435 Owner’s
BATTERY OPERATION, CONT.
Battery Installation/Replacement
To install or remove the batteries, the
following steps should be followed:
1. Make sure the AC power adapter is
unplugged.
2. Remove the indicator from the scale
column bracket. (Referring to Figure
No. 7, pull the spring plunger down and
slide the indicator up and away from the
bracket).
3. Turn the indicator over so that the
display is facing away from you.
4. Locate the rectangular panel on the
back of the indicator.
Spring
Plunger
Release
Figure No. 7
Battery
Cover
Push in and
lift here
5. To install or replace the batteries, first
remove the battery holder cover by
pushing in on the tab and lifting it up.
Refer to Figure No. 8.
6. If installing new batteries, proceed to
step 7. If replacing the batteries, remove
all 6 batteries from the battery holder
and then proceed to step 7.
7. Install the 6 new “AA” size batteries in
the battery holder, noting the polarity
markings located in the battery holder.
Refer to Figure No. 8.
Figure No. 8
8. After placing all 6 batteries in the holder,
replace the battery cover.
9. Turn the indicator over (display facing
up) and press the ON/OFF key.
10. If the display turns on, the batteries
have been installed correctly. If not,
remove the panel and check for one or
more improperly positioned batteries.
11. Return the indicator to the scale column
bracket. Refer to the steps on page 3.
+
-
+
+
-
+
+
-
-
+
12. The scale is now ready for operation.
For more information on setup and
operation of the indicator, see the
750 Owner’s Manual (8555-M483-O1).
Figure No. 9
8525-M316-O1 Rev B x 8435 Owner’s
5
OPERATION
CAUTION!
Do not leave the baby unattended in the baby tray. Failure to
maintain continual control of the baby can result in serious
injuries should the baby fall from the baby tray.
Basic Weighing
1. Place scale on a level, stable surface.
2. With the baby tray empty, press the
ON/OFF key to turn on the indicator.
3. If required, press the ZERO key to zero
the weight display.
4. Lay the baby being weighed in the
center of the baby tray. This will
distribute the weight evenly across the
scale platform.
5. When the weight is stable (STABLE [\
annunciator will turn on), read the
weight display.
6. If a printer is connected to scale, press
the PRINT key to print a ticket.
7. Remove the baby from baby tray.
Zero Weight Display
1. If the indicator display is not showing
zero weight, press the ZERO key.
Figure No. 10
2. Weight display will return to zero. ZERO and STABLE [\ annunciators will turn on to
show a stable, center-of-zero (Æ0Å) weight condition.
Zero Weight Display with Item on Scale
1. Place the item (blanket or similar covering) on the scale.
2. The display will show the weight of the item on the scale.
3. Press the ZERO key.
4. The weight display will return to zero. ZERO and STABLE [\ annunciators will turn on.
The weight of the item has been "zeroed off".
5. Lay the baby being weighed in the center of the baby tray. This will distribute the weight
evenly across the scale platform.
6. When the weight is stable (STABLE [\ annunciator will turn on), read the weight
display.
7. If a printer is connected to scale, press the PRINT key to print a ticket.
8. Remove the baby from baby tray.
6
8525-M316-O1 Rev B x 8435 Owner’s
REPLACEMENT PART IDENTIFICATION
I
2
3
4
Item
Qty.
Part Number
Description
1
1
0033-0532-0A
TOP PLATE ASSY
2
1
0033-0533-0A
PLATFORM ASSY
3
1
0033-0534-0A
LOAD CELL ASSY
4
¸
1
0033-0546-08
BASE FEET
1
33P50
BABY TRAY
¸
1
750
DIGITAL WEIGHT INDICATOR
¸ Not Shown
8525-M316-O1 Rev B x 8435 Owner’s
7
STATEMENT OF LIMITED WARRANTY
Detecto Scale warrants its equipment to be free from defects in
material and workmanship as follows: Detecto warrants to the
original purchaser only that it will repair or replace any part of
equipment which is defective in material or workmanship for a
period of two (2) years from date of shipment. Detecto shall be
the sole judge of what constitutes a defect.
During the first ninety (90) days Detecto may choose to
replace the product at no charge to the buyer upon inspection of
the returned item.
After the first ninety (90) days, upon inspection of the returned
item, Detecto will repair or replace it with a remanufactured
product. The customer is responsible for paying for the freight
both ways.
This warranty does not apply to peripheral equipment not
manufactured by Detecto; this equipment will be covered by
certain manufacturer’s warranty only.
This warranty does not include replacement of expendable or
consumable parts. This does not apply to any item which has
deteriorated or damaged due to wear, accident, misuse, abuse,
improper line voltage, overloading, theft, lightning, fire, water or
acts of God, or due to extended storage or exposure while in
purchaser’s possession. This warranty does not apply to
maintenance service. Purchased parts will have a ninety (90)
day repair or replacement warranty only.
Detecto may require the suspect product to be returned to the
factory; item(s) must be properly packed and shipping charges
prepaid. A return authorization number must be obtained for all
returns and marked on the outside of all returned packages.
Detecto accepts no responsibility for loss or damage in transit.
8
8525-M316-O1 Rev B x 8435 Owner’s
STATEMENT OF LIMITED WARRANTY
Conditions Which Void Limited Warranty
This warranty shall not apply to equipment which:
A.) Has been tampered with, defaced, mishandled or has had
repairs and modifications not authorized by Detecto.
B.) Has had serial number altered, defaced, or removed.
C.) Has not been grounded according to Detecto’s
recommended procedure.
Freight Carrier Damage
Claims for equipment damaged in transit must be referred to the
freight carrier in accordance with freight carrier regulations.
This warranty sets forth the extent of our liability for breach of
any warranty or deficiency in connection with the sale or use of
the product. Detecto will not be liable for consequential damages
of any nature, including but not limited to, loss of profit, delays or
expenses, whether based on tort or contract. Detecto reserves
the right to incorporate improvements in material and design
without notice and is not obligated to incorporate improvements
in equipment previously manufactured.
The foregoing is in lieu of all other warranties, express or implied
including any warranty that extends beyond the description of
the product including any warranty of merchantability or fitness
for a particular purpose. This warranty covers only those Detecto
products installed in the forty-eight (48) contiguous continental
United States.
Ph. (800) 641-2008
E-mail: [email protected]
203 E. Daugherty
Webb City, MO 64870
8525-M316-O1 Rev B x 8435 Owner’s
08/27/2014
Printed in USA
D268-WARRANTY-DET-A
9
Cardinal Scale Manufacturing Co.
102 E. Daugherty, Webb City, MO 64870 USA
Ph: 417-673-4631 or 1-800-641-2008
Fax: 417-673-2153
Technical Support: 1-866-254-8261
E-mail: [email protected]
10
8525-M316-O1
Rev B 04/208525-M316-O1 Rev B x 8435 Owner’s
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement