Detecto 210 User manual

Detecto 210 User manual
210 and 215
WEIGHT INDICATOR
Installation and Technical Manual
8200-M411-O1 Rev D
02/11
203 E. Daugherty, Webb City, MO 64870 USA
Ph: 417-673-4631  Fax: 417-673-2153
www.cardinalscale.com
Technical
Support:Rev
Ph:D866-254-8261
 [email protected]
8200-M411-O1
 210/215 Installation
& Technical
Printed in USA
1
2
8200-M411-O1 Rev D  210/215 Installation & Technical
TABLE OF CONTENTS
SPECIFICATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 1
Standard Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 2
Optional Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 2
Certifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 2
EUROPEAN DECLARATION OF CONFORMITY - - - - - - - - - - - - - - - - - - - - - - - - - - Page 3
PRECAUTIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 4
SITE PREPARATION REQUIREMENTS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 4
INSTALLATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 6
MOUNTING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 6
LOAD CELL CONNECTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 7
LOAD CELL CONNECTIONS WITH OVER 30 FEET OF CABLE - - - - - - - - - - - - - Page 8
SERIAL I/O CABLE INSTALLATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 9
OPTICALLY ISOLATED INPUTS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 9
OPTICALLY ISOLATED OUTPUTS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 9
RELAY BOARD (Optional) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 10
MAIN PCB (Figure No. 8) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 11
MAIN PCB JUMPERS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 12
RE-INSTALLING THE REAR PANEL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 12
KEYPAD FUNCTIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 13
ANNUNCIATORS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 18
SETUP AND CALIBRATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 20
SETUP REVIEW - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 39
CALIBRATION "C" NUMBERS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 39
ACCUMULATORS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 40
BEFORE YOU CALL SERVICE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 41
ERROR CODES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 42
CALIBRATION SEAL INSTALLATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 43
AXLE WEIGHER OPERATION MODE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 44
PART IDENTIFICATION (210) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 46
PART IDENTIFICATION (215) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 50
APPENDIX A: MODEL 210DC and 215DC - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 55
SERIAL NUMBER _____________________
DATE OF PURCHASE _________________
PURCHASED FROM __________________
____________________________________
____________________________________
____________________________________
RETAIN THIS INFORMATION FOR FUTURE USE
PRECAUTIONS
Before using this indicator, read this manual and pay special attention to all
"WARNING" symbols:
IMPORTANT
ELECTRICAL
WARNING
STATIC
SENSITVE
8200-M411-O1 Rev D  210/215 Installation & Technical
II
FCC COMPLIANCE STATEMENT
WARNING! This equipment generates uses and can radiate radio frequency and if not
installed and used in accordance with the instruction manual, may cause interference to radio
communications. It has been tested and found to comply with the limits for a Class A
computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when operated in a commercial environment.
Operation of this equipment in a residential area may cause interference in which case the
user will be responsible to take whatever measures necessary to correct the interference.
You may find the booklet “How to Identify and Resolve Radio TV Interference Problems”
prepared by the Federal Communications Commission helpful. It is available from the U.S.
Government Printing Office, Washington, D.C. 20402, stock No. 001-000-00315-4.
PROPER DISPOSAL
When this device reaches the end of its useful life, it must be properly disposed of. It must not
be disposed of as unsorted municipal waste. Within the European Union, this device should
be returned to the distributor from where it was purchased for proper disposal. This is in
accordance with EU Directive 2002/96/EC. Within North America, the device should be
disposed of in accordance with the local laws regarding the disposal of waste electrical and
electronic equipment.
It is everyone’s responsibility to help maintain the environment and to reduce the effects of
hazardous substances contained in electrical and electronic equipment on human health.
Please do your part by making certain that this device is properly disposed of. The symbol
shown below indicates that this device must not be disposed of in unsorted municipal waste
programs.
All rights reserved. Reproduction or use, without expressed written permission, of editorial or
pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to
the use of the information contained herein. While every precaution has been taken in the
preparation of this manual, the Seller assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting from use of the information contained
herein. All instructions and diagrams have been checked for accuracy and ease of application;
however, success and safety in working with tools depend to a great extent upon the individual
accuracy, skill and caution. For this reason the Seller is not able to guarantee the result of any
procedure contained herein. Nor can they assume responsibility for any damage to property or
injury to persons occasioned from the procedures. Persons engaging the procedures do so
entirely at their own risk.
IIII
8200-M411-O1 Rev D  210/215 Installation & Technical
SPECIFICATIONS
Unless otherwise noted, the specifications apply to both the Model 210 and Model 215.
Power Requirements:
Enclosure Type:
Enclosure Size:
Weight:
Operating Environment:
Display:
Transducer Excitation:
(Jumper selectable)
Signal Input Range:
Number of Load Cells:
Load Cell Cable Length:
Division Value:
Sensitivity:
NON-COMMERCIAL
NTEP
CANADA
OIML
Scale Divisions:
NON-COMMERCIAL
NTEP
CANADA
OIML
Internal Resolution:
Tare Capacity:
Sample Rate:
Auto Zero Range:
Weighing Units:
Keypad:
Standard I/O:
Battery Operation:
100 to 240 VAC (50/60 Hz) at 0.4A Max.
Stainless Steel wall or desk-mount
9 3/16" W x 7 1/2" H x 3 1/8" D
(233mm W x 191mm H x 79mm D)
8.2lbs - (9.6lb with battery)
Temperature: 14 to 104 ºF (-10 to +40 ºC)
Humidity: 90% non-condensing (maximum)
210
215
Six digit, seven segment,
Six digit, seven segment,
0.6" high LED
1" high LCD
12 VDC
8 VDC with battery operation (jumper selectable)
1.0 mV min. to 40 mV max. (with dead load boost)
8 each, 350 OHM minimum resistance
1500 feet maximum. Consult factory for other requirements
30 feet maximum without sense lines
1, 2, or 5 x 10, 1, 0.1, 0.01, 0.001 commercial
0 to 99, non-commercial
0.15 uV/e
0.3uV/e (Class III/IIIL)
0.3uV/e (Class III/IIIHD)
0.7 uV/e (Class III)
100 to 240,000
100 to 10,000 (Class III/IIIL)
100 to 10,000 (Class III/IIIHD)
100 to 10,000 (Class III)
1 part in 16,777,216
Scale Capacity
1 to 100 samples per second, selectable
0.5 or 1 through 9 divisions
210
215
Tons, Pounds, Pounds-Ounces,
Pounds, Pounds-Ounces,
Ounces, Metric Tons, Kilograms,
Ounces, Kilograms, Grams
Grams
Color coded Membrane type, 22 keys
(1) bi-directional RS232 (20mA)
(1) output only RS232 (20mA)
210EU - CAM-350 Type, 12V 2Ah
215 – 10 “AA” Size, NiMH, 2300mAh
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
ATTENTION: RISQUE D'EXPLOSION SI LA BATTERIES EST REMPLACE'E PAR UN
TYPE INCORRECT. REJETEZ LES BATTERIES UTILISE'ES SELON LES
INSTRUCTIONS.
8200-M411-O1 Rev D  210/215 Installation & Technical
1
SPECIFICATIONS, CONT.
Unless otherwise noted, the specifications apply to both the Model 210 and Model 215.
Standard Features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Push button tare function
Gross, tare, net conversion
Selectable key lockout
Hi-Resolution mode
Adjustable filtering
Gross and Net accumulators
Dual serial ports
Remote input lines for Zero, Tare, Gross and Print (1000 feet maximum)
Programmable print format using Visual Print or nControl (2 Visual Tickets available)
SMA level 2 compliant serial communications
(For more information see http://www.scalemanufacturers.org)
Field re-programmable via PC interconnection
Test feature (performs display and internal tests)
Auto Shutoff and Sleep modes
Battery operation
(Requires additional hardware and includes additional documentation)
Numeric keypad
Keypad tare function
Count feature with accumulator
Time and Date with selectable 12 or 24 hour operation
Checkweigher
Three Preset Weight Comparators
Axle Weigher (CWL-40) Operation Mode
Optional Features:
Analog Output*, Allen-Bradley Interface*, 10/100 mbps Ethernet Adapter*, Additional Serial
Port*, Checkweigher Light Bar*, Internal Relay Box*, External Relay Box*, Special Filtering,
and Column Mounting
*This feature requires additional hardware and includes additional documentation.
Certifications:
This equipment is certified to comply with the requirements for a Class III/IIIL device by the
2
•
National Conference on Weights and Measurements (Certificate No. 01-011)
•
Measurement Canada (Approval No. AM-5397)
•
And for a Class III device by OIML R-76 (Certificate No. DK 0199.47).
8200-M411-O1 Rev D  210/215 Installation & Technical
EUROPEAN DECLARATION OF CONFORMITY
Manufacturer: Cardinal Scale Manufacturing Company
PO Box 151
203 East Daugherty
Webb City, Missouri 64870 USA
Telephone No. (417) 673-4631
Fax No.
(417) 673-5001
Product:
Non-automatic Weight Indicating Instrument
Model Numbers 200, 205, 210, 210FE, 215, 220 and 225
Serial Number EXXXYY-ZZZ
where XXX = day of year
YY = last two digits of year
ZZZ = sequential number
The undersigned hereby declares, on behalf of Cardinal Scale Manufacturing Company of
Webb City, Missouri, that the above-referenced product, to which this declaration relates, is in
conformity with the provisions of:
European Standard EN 45501: 1992 and equivalent International
Recommendation OIML R76, edition 1992
EU Type Approval Certificate Number DK 0199.159
Report No. DANAK-1910304
Council Directive 2006/95/EC Low Voltage Directive
as amended by Council Directive 93/68/EEC (22 July, 1993)
Council Directive 90/384/EEC (20 June, 1990) on the Harmonization
Of the Laws of Member States relating to non-automatic weighing
Systems as amended by:
Council Directive 93/68/EEC (22 July, 1993)
European Standard EN50082: 1995 for radiated emissions and
European Standard EN50082-2: 1995 Class B for EMC immunity.
The Technical Construction File required by this Directive is maintained at the corporate
headquarters of Cardinal Scale Manufacturing Company, 203 East Daugherty, Webb City,
Missouri.
____________________
Ginger Harper
Director, Quality Assurance
8200-M411-O1 Rev D  210/215 Installation & Technical
3
PRECAUTIONS
Static Electricity
CAUTION! This device contains static sensitive circuit cards and components.
Improper handling of these devices or printed circuit cards can result in damage to or
destruction of the component or card. Such actual and/or consequential damage IS
NOT covered under warranty and is the responsibility of the device owner. Electronic
components must be handled only by qualified electronic technicians who follow the
guidelines listed below.
ATTENTION! ALWAYS use a properly grounded wrist strap when handling,
removing or installing electronic circuit cards or components. Make certain that the
wrist strap ground lead is securely attached to an adequate ground. If you are
uncertain of the quality of the ground, you should consult a licensed electrician.
ALWAYS handle printed circuit card assemblies by the outermost edges. NEVER
touch the components, component leads or connectors. ALWAYS observe warning
labels on static protective bags and packaging and never remove the card or
component from the packaging until ready for use. ALWAYS store and transport
electronic printed circuit cards and components in anti-static protective bags or
packaging.
SITE PREPARATION REQUIREMENTS
The Cardinal 210/215 indicators are precision weight-measuring instruments. As with any
precision instrument, they require an acceptable environment to operate at peak performance
and reliability. This section is provided to assist you in obtaining such an environment.
Environmental
The Model 210/215 indicators meet or
exceeds all certification requirements
within a temperature range of 14 to 104 °F
(-10 to +40 °C).
In order to keep cooling requirements to a
minimum, the indicator should be placed
out of direct sunlight and to provide
adequate air circulation, keep the area
around the indicator clear.
Make certain the indicator is not directly in
front of a heating or cooling vent. Such a
location will subject the indicator to
sudden temperature changes, which may
result in unstable weight readings.
Insure that the indicator has good, clean
AC power and is properly grounded.
In areas subject to lightning strikes,
additional protection to minimize lightning
damage, such as surge suppressors,
should be installed.
4
8200-M411-O1 Rev D  210/215 Installation & Technical
SITE PREPARATION REQUIREMENTS, CONT.
Electrical Power
The 210/215 indicators have been designed to operate from 100 to 240 VAC at 50/60 Hz.
Note that a special order is not required for operation at 230/240 VAC.
CAUTION! - To avoid electrical hazard and possible damage to the indicator,
DO NOT, under any circumstance, cut, remove, alter, or in any way bypass the
power cord grounding prong.
•
The socket-outlet supplying power to the indicator should be on a separate circuit from the
distribution panel and dedicated to the exclusive use of the indicator.
•
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Note that the power cord on the 210/215 (without the Battery Option) serves as the power
disconnect.
•
The wiring should conform to national and local electrical codes and ordinances and should
be approved by the local inspector to assure compliance.
•
For outdoor operations, the socket-outlet must provide GFCI (ground fault circuit
interrupter) protection.
•
On installations requiring 230/240 VAC power, it is the responsibility of the customer to
have a qualified electrician install the proper power cord plug that conforms to national
electrical codes and local codes and ordinances.
Electrical Noise Interference
To prevent electrical noise interference, make certain all other wall outlets for use with air
conditioning and heating equipment, lighting or other equipment with heavily inductive loads,
such as welders, motors and solenoids are on circuits separate from the indicator. Many of
these disturbances originate within the building itself and can seriously affect the operation of
the indicator. These sources of disturbances must be identified and steps must be taken to
prevent possible adverse effects on the indicator. Examples of available alternatives include
isolation transformers, power regulators, uninterruptible power supplies, or simple line filters.
Transient Suppression
The following recommendations will help to reduce transients:
 Always use shielded cables to connect signal wires to the weight indicator.

Secure the cables in the cable clips provided inside the indicator.

Connect the cable shield (indicator end only) to a ground point inside the indicator. Keep
wires that extend beyond the shield as short as possible.

Do not run load cell or signal cables from the weight indicator along side or parallel to
wiring carrying AC power. If unavoidable, position the load cell and signal cables a
minimum of 24" away from all AC wiring.

Always use arc suppressors across all AC power relay contacts (see recommendations at
http://www.paktron.com/pdf/Quencharch_QRL.pdf).

Use zero voltage switching relays, optically isolated if possible.
8200-M411-O1 Rev D  210/215 Installation & Technical
5
INSTALLATION
Before beginning installation of your Model 210/215 Weight Indicator, make certain that the
indicator has been received in good condition. Carefully remove the indicator from the
shipping carton and inspect it for any evidence of damage (such as exterior dents or
scratches) that may have taken place during shipment. Keep the carton and packing material
for return shipment if it should become necessary. It is the responsibility of the purchaser to
file all claims for any damages or loss incurred during transit.
Mounting
NOTE! Should your 210/215 indicator come already installed on a scale, the following
information describing the installation of the indicator does not apply.
The Model 210/215 Indicator is housed in a Stainless Steel wall or desk-mount enclosure. The
gimbal may be mounted on a desktop or other smooth, flat, horizontal surface or may be
mounted on a wall. Refer to Figure No. 1 for a layout of wall-mounting bolts.
+
6.00"
+
Clearance for
#10 size screw
Figure No. 1
If wall mounted, make certain the mounting surface is strong enough to support the indicator.
The mounting location should be where the display is easily viewed while being close enough
to provide the operator easy access to the keypad. Carefully lay out the mounting hole
locations, then drill and install the anchor bolts. Attach the gimbal to the wall and securely
tighten the retaining bolts.
Load Cells
Battery Access Cover
6
8200-M411-O1 Rev D  210/215 Installation & Technical
Figure No. 2
INSTALLATION, CONT.
Load Cell Connection
CAUTION! Disconnect any external load cell power supply before connecting
load cells to the indicator. Failure to do so will result in permanent damage to the
indicator.
Load Cell Cable Connection for RFI Suppression
The load cell cable should be routed through the special metallic gland connector and the
shield wire must be connected to this gland connector for grounding and to eliminate RFI.
Refer to Figure No. 2 and Figure No. 3 for the appropriate gland connector.
1. Remove the three acorn nuts securing the
Battery Access Cover to the bottom of the
indicator and then remove the battery tray
(Model 215) or the battery (Model 210).
2. After removing the battery tray or battery,
remove the 12 acorn nuts securing the back
panel to main housing.
3. Loosen and remove the metal gland
connector nut and remove the plastic insert.
4. Route the load cell cable through the nut and
plastic insert and into the enclosure.
5. With the load cell cable routed into the
enclosure, remove approximately 18 to 20
inches of the outer insulating jacket from the
cable exposing the internal wires.
6. Cut the shield wire so that it extends past the
outer jacket approximately 3/4 inch.
7. Remove 1/4" of insulation from the end of
each of the 4 wires (without sense leads) or 6
wires with sense leads (refer to figure No. 4).
8. Connect each of the wires to terminal block
P1 referring to labels on circuit board for
terminal connections. Refer to Figure No. 8
for terminal block location.
9. To terminate a wire, press down on release
bar for the terminal, insert wire into terminal
opening then allow release bar to return to its
original position, locking wire in place.
Repeat procedure until all wires are in place.
10. Route load cell cable wires through the two
cable clips provided on upper and left sides
of enclosure interior.
TERMINAL NO.
1
2
3
LOAD CELL TERMINAL BLOCK P1
Function
TERMINAL NO.
+ EXCITATION
5
+ SENSE
6
+ SIGNAL
7
Figure No. 3
Figure No. 4
Function
- SIGNAL
- SENSE
- EXCITATION
NOTE! If the sense leads are NOT used, you must install plug-in jumpers at J4 and J5
adjacent to the terminal block. These jumpers attach the sense leads to the excitation leads.
If sense leads ARE used (as in motor truck scales), these plug-in jumpers should be positioned
on one plug-in pin only or removed and stored for later use (see Figure No. 8).
8200-M411-O1 Rev D  210/215 Installation & Technical
7
INSTALLATION, CONT.
Load Cell Cable Shield Wire Connection for RFI Suppression
1. After all terminations have been made,
remove the excess cable from the enclosure.
2. Referring to Figure No. 5, fold the shield wire
back over the plastic insert and then insert the
plastic insert (with the shield wire) into the
gland connector.
3. The shield wire is secured when tightening the
gland connector nut.
4. Do not over-tighten the connector but make
certain it is snug.
5. DO NOT USE TOOLS! Finger tighten only!
Figure No. 5
Load Cell Cable Connection (Standard Gland Connector)
The following instructions describe the load cell connection should it be desired to route the
load cell cable through a standard gland connector. If a standard gland connector is used, the
shield wire should be connected to the threaded stud inside the indicator enclosure.
1. Remove the three acorn nuts securing the Battery Access Cover to the bottom of the
2.
3.
4.
5.
6.
7.
indicator and then remove the battery tray (Model 215) or the battery (Model 210).
After removing the battery tray or battery, remove the 12 acorn nuts securing the back
panel to main housing, and then loosen a gland connector for the load cell cable. Refer to
Figure No. 2 for illustration of connector layout.
Slip the single cable from the load cell or load cell junction box through the gland connector
and into the enclosure.
Remove 3" of the outer insulation jacket then remove 1/4" of insulation from each of the 4
wires and shield (without sense leads) or 6 wires and shield (with sense leads). Refer to
Figure No. 4.
Connect each of the wires to terminal block P1 referring to labels on circuit board for
terminal connections. Refer to Figure No. 8 for terminal block location.
To terminate a wire, first press down on release bar for the terminal, insert wire into
terminal opening then allow release bar to return to its original position, locking wire in
place. Repeat procedure until all of wires are in place.
Route load cell cable through the two cable clips provided on upper and left sides of
enclosure interior.
Load Cell Cable Shield Wire Connection (Standard Gland Connector)
The load cell cable shield wire should be connected to the
threaded stud inside the indicator. This stud is located on
the top inside of the indicator near the load cell connector
P1. See Figure No.6.
Threaded Stud
P1 Load Cell
The shield wire should be wrapped around the stud
between the 2 flat washers and secured using hex nut.
Figure No. 6
Load Cell Connections With Over 30 Feet Of Cable
For installations with over 30 feet of cable between the indicator and the load cells, sense
wires should be used. The sense wires must be connected between the +SENS, -SENS
terminals on the indicator and the +EXCITATION, -EXCITATION wires of the load cells or the
+SENS, -SENS terminals of the load cell trim board or the section seal trim board.
8
8200-M411-O1 Rev D  210/215 Installation & Technical
INSTALLATION, CONT.
Serial I/O Cable Installation
The 210/215 indicators may be connected to a printer to record weight and associated data or
it may be connected to a remote display or even to a computer for transmission of weight data.
The weight data may be transmitted on demand (pressing the PRINT key or on receipt of a
command from the computer). Refer to the Setup, SIO Serial I/O section of this manual.
1. Remove the 12 acorn nuts securing the back panel to main housing, then loosen a gland
connector for the serial cable. Refer to Figure No. 2 for illustration of connector layout.
2. Slip the serial cable through the gland connector and into the enclosure.
3. Remove 2" of the outer insulation jacket then remove 1/4" of insulation from each of the
wires (refer to Figure No. 4).
4. Connect each of the wires to the Serial Data terminal block (P11) referring to Figure No. 8
for terminal block locations.
5. To terminate, first press down on the release bar for the terminal, insert the wire into the
opening then allow the release bar to return to its original position, locking the wire in place.
Repeat the procedure until all of the wires are in place.
BI-DIRECTIONAL SERIAL INTERFACE
TERMINAL NO.
Function
1
TXD 1 - RS232
2
RXD 1 - RS232
3
TXD 1 – 20 mA Active
4
GROUND
SERIAL OUTPUT
TERMINAL NO.
Function
5
TXD 2 - RS232
6
TXD 2 – 20 mA Active
7
GROUND
Optically Isolated Inputs (requires additional hardware)
Included with the I/O are 4 programmable inputs that may be used to remotely (up to 100 feet)
initiate various functions within the indicator. These inputs are accessed via a terminal block
(P9) on the back of the PC board (see Figure No. 8). The 4 inputs are defined as follows:
TERMINAL NO.
1
2
3
4
5
Function
Gross
Print
Zero
Tare
Common
NOTE! The input must be connected to Gnd to initiate the function.
Optically Isolated Outputs (requires additional hardware)
Preset Weight Comparator Checkweigher Logic Level Output
If desired, you may use the optically isolated outputs from your Model 210/215 indicator’s
preset weight comparators or checkweigher to remotely (up to 100 feet) control peripheral
devices used to manage the flow of material or signal when the weight is within preset limits.
J11 (12V) - ACTIVE REMOTE OUT JUMPER
The Active Remote Out jumper J11, when connected, allows the 210/215 indicator to supply
(source) 12 VDC to a solid-state relay or other load of 200 ohms or greater. To operate from
the 12 VDC source, the positive connection from the relays must be connected to the PWC
connector pins and the negative wire from the relays to the GND pin. See Figure No. 8 for
jumper and REMOTE OUTPUT connector location.
8200-M411-O1 Rev D  210/215 Installation & Technical
9
INSTALLATION, CONT.
For completely isolated outputs, J11 must be open (positioned on one plug-in pin only or
removed) and the user must provide 12 to 24 VDC to the SRC pin and a ground return to the
load. The load must still be 200 ohms or greater.
To connect the control cable to the preset weight comparator/checkweigher logic level output
connector P10, first loosen the gland connector located on the right side on the back of the
210/215. Refer to Figure No. 8 for the exact location of the connector. Slip the cable through
the connector and into the enclosure. Remove 2 inches of the cable insulating jacket and then
1/4 inch of insulation from each of the internal wires (refer to Figure No. 4). Make the proper
terminations on terminal block P10. To terminate a wire, first press down on the terminal block
release bar, insert the wire into the terminal and remove pressure from the release bar locking
the wire in place.
Relay Board - (Optional)
The relay board (Cardinal p/n 8539-C062-0A) is mounted in the RB4-F external junction box
for use with the 210/215 Indicator. Connect devices to be controlled as shown in Figure No. 7.
The relays must be configured to be on (closed) or off (open) at weights under the preset
weight then switch at the preset weight from on-to-off or off-to-on by setting the under weight
condition to on or off during setup and calibration or setup review. Refer to the Setup and
Calibration, “d out” (Digital Output) section of this manual for more information.
EXAMPLE: d oUt= 1,1
The PWC1 relay is on (closed) for weights under the preset weight and off (open) for weights
equal to or over the preset weight.
Figure No. 7
NOTE! All relays are the “normally-open” type that will open when power to
indicator is lost.
10
8200-M411-O1 Rev D  210/215 Installation & Technical
INSTALLATION, CONT.
Main PCB
Figure No. 8
8200-M411-O1 Rev D  210/215 Installation & Technical
11
INSTALLATION, CONT.
Main PCB Jumpers
J1 - BATTERY CHARGE MODE (210 Only)
Place jumper J1 in the Full position when operating the indicator totally from battery power and
only recharging the battery pack when it is low. Place jumper J1 in the Trickle position when
operating the indicator from commercial power and using the battery pack to supply power only
in the event of a power loss.
J2 - AUTO-ON JUMPER
The AUTO-ON jumper J2, when connected, will cause the indicator to power on automatically
whenever power is applied to the power input connector. If power is lost momentarily and then
reapplied, the indicator will turn on without pressing the ON key.
J3 - 8V EXCITATION JUMPER
The 8V EXCITATION jumper J3, when connected, sets the load cell excitation voltage to 8V
for operation with the 12 VDC battery. To operate from the 12 VDC battery, the load cell
excitation voltage MUST be set to 8 VDC (J3 closed). Battery operation with the load cell
excitation voltage set to 12V will result in an unstable weight display.
J4 AND J5 - SENSE JUMPERS
If the sense leads are NOT used, you must install plug-in jumpers at J4 and J5 adjacent to the
terminal block. These jumpers attach the sense leads to the excitation leads. If sense leads
ARE used (as in motor truck scales), these plug-in jumpers should be positioned on one plugin pin only or removed and stored for later use.
J10 - DEAD LOAD BOOST JUMPER
For very low dead loads (less than 10% of the combined load cell capacity) connect the dead
load boost jumper J10 on the printed circuit board.
J11 – PWC SRC (SOURCE)
The J11 jumper, when connected (closed) supplies 12 VDC from the 210/215 indicator to a
solid-state relay or other load of 200 ohms or greater. When J11 is open (positioned on one
plug-in pin only or removed), the 12 to 24 VDC must be provided from an external source to
P10-6. The load must still be 200 ohms or greater.
Re-Installing The Rear Panel
After all terminations have been made, remove the excess cable from the indicator enclosure
and securely tighten each of the cable gland connectors. Do not over-tighten these connectors
but make certain they are snug. DO NOT USE TOOLS! Finger tighten only! Insure any
unused gland connectors are plugged.
1. Make certain no cables or wires are exposed between the main housing and rear panel and
then place the rear panel onto the main housing.
2. Secure with the 12 acorn nuts removed earlier. Follow a diagonal pattern when tightening
the acorn nuts.
3. Slide the battery (Model 210) or battery tray (Model 215) into the opening, until you feel
resistance and the edge of the battery/battery tray is flush with the bottom of the indicator.
4. Replace the Battery Access Cover and install the three acorn nuts removed earlier,
securing the battery/battery tray in place.
IMPORTANT! On the Model 215, the battery tray (with or without batteries) must be
installed for the indicator to function.
12
8200-M411-O1 Rev D  210/215 Installation & Technical
KEYPAD FUNCTIONS
The Model 210/215 is equipped with a 22-key keypad. The keypad is used to enter commands
and data into the indicator. This section describes each key along with its normal function. It is
helpful to refer to the actual indicator while reading this section.
Figure No. 9 (210 Keypad)
Figure No. 10 (215 Keypad)
DO NOT operate the keypad with pointed objects (pencils, pens, etc).
Damage to keypad resulting from this practice is NOT covered under warranty.
8200-M411-O1 Rev D  210/215 Installation & Technical
13
KEYPAD FUNCTIONS, CONT.
ON/OFF KEY
This key performs two functions. Pressing it when the indicator is off will apply power to the
indicator. If the indicator is already on, pressing this key will turn the indicator off.
COUNT/SAMPLE KEY
This key performs two functions. The first time it is pressed, the indicator will count (unless
piece weight is 0). The second time it is pressed (or if pct=0
on the first press) will show the
w
prompt ADD=5 on the display. Continued pressing of the COUNT/SAMPLE key will toggle
between the ADD=5, 10, 25, 50, 75 prompts to select a sample size. When desired sample
size is displayed, press the ENTER key OR with ADD=X(5, 10 etc.) displayed, using the
numeric keypad, key-in any desired sample value, then press the ENTER key. Press the
ASTERISK key to abort the input operation. To exit the count function and display weight,
press the NET/GROSS key.
TIME/DATE KEY
This key is used to enter the clock mode to program the time, date and consecutive number.
Pressing the TIME/DATE key will enter the clock mode with the 210/215 displaying HoUr=.
12-Hour Format Selected In Setup (td=12)
1. With the display showing HoUr=, press the ENTER key.
2. If the time displayed is correct, press the ENTER key and proceed to step 4.
3. If the displayed time is incorrect, use the numeric keys to enter the correct time and
press the ENTER key.
4. The display will change to A=. Press the ENTER key.
5. The display will show YES.
• If the time is before noon (12:00 PM), press the ENTER key.
• If the time is after noon (12:00 PM), press the 0/NO key, then press the ENTER key.
6. The display will show dAtE=. Press the ENTER key.
7. If the date displayed is correct, press the ENTER key to proceed to the consecutive
number prompt, Cn.C .n=.
8. If the date displayed is incorrect, use the numeric keys to enter the correct date and
press the ENTER key to proceed to the consecutive number prompt. Remember to
enter the date in the same format (month-day-year or day-month-year) as selected by
the USA setup parameter. Note that with the USA=YES setting, the date format is
month-day-year.
24-Hour Format Selected In Setup (td=24)
1. With the display showing HoUr=, press the ENTER key.
2. If the time displayed is correct, press the ENTER key and proceed to step 4.
3. If the displayed time is incorrect, use the numeric keys to enter the correct time and
press the ENTER key. Note that with the 24-hour format selected, entering all times
after noon (12:00 PM), you must add 12 to the time, i.e. 3 PM would be 1500.
4. The display will show dAtE=. Press the ENTER key.
5. If the date displayed is correct, press the ENTER key to proceed to the consecutive
number prompt, Cn.C .n=.
6. If the date displayed is incorrect, use the numeric keys to enter the correct date and
press the ENTER key to proceed to the consecutive number prompt. Remember to
enter the date in the same format (month-day-year or day-month-year) as selected by
the USA setup parameter. Note that with the USA=YES setting, the date format is
month-day-year.
14
8200-M411-O1 Rev D  210/215 Installation & Technical
KEYPAD FUNCTIONS, CONT.
Consecutive Number
If the consecutive number displayed is correct, press the ENTER key to resume normal
operation. If the consecutive number displayed is incorrect, use the numeric keys to enter
the correct consecutive number (up to 6 digits) and press the ENTER key to resume normal
operation.
PRESET KEY
This key is used to enter the weight values for the three preset weight comparators or for the
checkweigher feature depending on which feature was selected (setup parameter d out)
during setup and calibration.
Preset Weight Comparator
If the Preset Weight Comparator feature was selected, the PWC1 annunciator will flash and
the display will show the currently stored value for the number 1 preset weight comparator.
If the value displayed is acceptable, press the ENTER key, otherwise, use the numeric keys
to enter the new preset value and press the ENTER key. The PWC2 annunciator will now
flash and the display will show the currently stored value for the number 2 preset weight
comparator. As before, if the value displayed is acceptable, press the ENTER key,
otherwise, use the numeric keys to enter the new value and press the ENTER key. The
PWC3 annunciator will now flash and the display will show the currently stored value for the
number 3 preset weight comparator. Again, if value displayed is acceptable, press the
ENTER key, otherwise, use numeric keys to enter a new value and press the ENTER key.
Checkweigher
If the Checkweigher feature was selected and the PRESET key pressed, the ACCEPT and
UNDER annunciators will flash and the preset value for the minimum acceptable weight will
be displayed. Press the ENTER key if the displayed value is correct or use the numeric
keys and enter the new value and press the ENTER key. The ACCEPT and OVER
annunciators will now flash and the display will show the minimum value of weight over the
accepted range. As before, if the value shown is correct, press the ENTER key. If the value
is incorrect, enter the new value and press the ENTER key to save it. Note that this value
must be greater than the accept value. Remember that both the preset weight comparators
and checkweigher functions operate on the absolute value of weight ignoring the polarity.
After the second preset value is entered, the indicator will return to normal operation.
PRINT KEY
Pressing this key will add the displayed gross or net weight or piece count to the associated
accumulator and initiate the transmission of weight and other data selected during setup of the
Print menu items via the selected printer output port (see Port= under Print menu) unless the
continuous data feature of this port was enabled during setup and calibration.
If the id= (ID Prompt) has been enabled during setup, when the PRINT key is pressed, the
indicator will prompt for an ID to be printed on the ticket.
If the A clr= is set to 1 (Yes), input up to 6 digits for the ID and then press the ENTER key
to complete the transaction. Upon pressing the ENTER key, the print function will occur.
If the A clr= is set to 0 (no), press the ENTER key to display the current ID. If ID
displayed is acceptable, press the ENTER key again to complete transaction. Otherwise,
input up to 6 digits for ID then press the ENTER key to complete the transaction. The print
function will occur after the ENTER key is pressed.
Note that the indicator will not respond to the Print command unless the weight display is
stable. If displaying gross weight, the only weight printed is gross weight. If displaying net
weight, the gross, tare, and net weights are printed.
8200-M411-O1 Rev D  210/215 Installation & Technical
15
KEYPAD FUNCTIONS, CONT.
The 210/215 includes support for visual tickets. Visual
tickets are designed by the PC based programs Visual
Print or nControl, then downloaded to the indicator.
Two programmable formats in addition to the standard
print tab settings are allowed.
Print formats are selected by using the ASTERISK and
PRINT keys in combination (refer to the next section
for details). NOTE! When the PRINT key is pressed,
the indicator looks for the selected format. If a visual
ticket is not found it reverts to the print tab settings.
#2
10:19 08/23/2009
100.00 lb G
20.00 lb T
80.00 lb N
0.00 lb GROSS ACCUM
272.00 lb NET ACCUM
TICKET EXAMPLE
ZERO/REVIEW KEY
This key performs two functions. In normal operation, pressing this key will cause an
immediate zeroing of the weight display up to the selected limit of 4% or 100% of the scale’s
capacity. Note that this selection is made during the setup and calibration of the indicator.
Pressing this key after the ASTERISK key will enter the Review mode of Setup and
Calibration. Refer to description of ASTERISK key and the Setup Review section of this
manual for details.
TARE KEY (with diamond "T" symbol)
This is a dual function key. Pressing the TARE key alone (Pushbutton Tare mode) will store
the current gross weight as a new tare weight and cause the weight display to change to the
net weight display mode (Net annunciator turns on). Pressing it key after entering a numeric
value (Keypad Tare) will cause the value entered to be accepted as a new tare weight.
NOTE! Tare weights equal to or greater than scale capacity cannot be entered. In addition,
keypad tare weight division value must be same as scale division value. For example, a
unit with .005 lb as division value will display Error if you enter 1.003 for tare weight.
NET/GROSS KEY
This key is used to toggle between Net and Gross weight modes. The selected mode is
indicated by turning on the appropriate annunciator on the display. Note that if no valid tare
weight has been entered, pressing this key will cause a momentary “notArE” display error and
the indicator will remain in the Gross weight mode.
TARE KEY (with weight "T"symbol)
Pressing this key will display the current tare weight for three seconds.
UNITS/TEST KEY
This key performs two functions. In normal operation, it is used to select the units in which the
weight is to be displayed. The available units of measure ("unit1" and "unit2") are enabled or
disabled in setup. The available units include tons, pounds only, pound-ounces, ounces only,
tonnes (metric tons), kilograms, and grams. Note that not all combinations are supported.
Pressing this key after the ASTERISK key will enter the Test mode. The Test mode is used to
conduct a test of all display elements. Refer to description of ASTERISK key for details.
0 THROUGH 9 KEYS
These keys are used to enter numeric data during the setup and calibration as well as during
normal operation of the indicator. NOTE: The 1 and 0 keys have dual functions. They are
used to enter numeric data during setup and calibration as well as during normal operations
and are also used to answer yes (1 = YES) or no (0 = NO) to various prompts.
ENTER KEY
This key serves two purposes. First, when reviewing setup parameters, pressing the ENTER
key will display the current setting of the parameter. Second, the ENTER key is used to signal
completion of the entry of data and causes the indicator to process the data entered.
16
8200-M411-O1 Rev D  210/215 Installation & Technical
KEYPAD FUNCTIONS, CONT.
ASTERISK KEY
This key is used for several functions. During Setup, when a setup parameter (not a
parameter value) is displayed, pressing it key will "backup" to the previous prompt. In normal
operation, this key is used in conjunction with other keys on the keypad to access additional
indicator features. These features and their associated key combinations are as follows:
ASTERISK, ZERO/REVIEW KEY
This combination will enter the Review mode of Setup and Calibration. Refer to
Setup Review section of this manual for details.
ASTERISK, NET/GROSS KEY
This combination will display the Net accumulator.
ASTERISK, NET/GROSS KEY, PRINT KEY
This combination will print the Net accumulator.
ASTERISK, NET/GROSS KEY, ZERO KEY
This combination will zero (clear) the Net accumulator.
ASTERISK, NET/GROSS KEY, NET/GROSS KEY
This combination will display the Gross accumulator.
ASTERISK, NET/GROSS KEY, NET/GROSS KEY, PRINT KEY
This combination will print the Gross accumulator.
ASTERISK, NET/GROSS KEY, NET/GROSS KEY, ZERO KEY
This combination will zero (clear) the Gross accumulator.
ASTERISK, UNITS KEY
This combination will enter the Test mode. The Test mode is used to test of all the
display elements. It consists of five (5) cycles, each lasting about one (1) second:
1. All horizontal segments will turn on (no annunciators).
2. All vertical segments and decimal points will turn on (no annunciators).
3. All annunciators will turn on.
4. All display elements off.
5. The model number (210) and the software version X.X.
6. The calibration numbers (C1 to C4).
ASTERISK, PRINT KEY
This combination is used to change the selected print ticket format. Pressing the
ASTERISK then the PRINT key will display a prompt “Prt=”. Press the ENTER key
to show the current value. If the setting displayed is acceptable, press the ENTER
key again to save it. Otherwise, using the numeric keys enter the new setting, then
press the ENTER key to save it. Allowable values are:
0 = print tab settings
1 = visual ticket format 1
2 = visual ticket format 2
In addition to using the ASTERISK, PRINT key combination to change the print ticket
format, the operator (just prior to printing the ticket) can change the print ticket format
at the end of the weighing operation. This is accomplished by performing the normal
weighing operation, then pressing the desired format number (0, 1 or 2), followed by
pressing the PRINT key.
NOTE! When a print format is selected (by either method), it will remain active
until changed by the operator.
8200-M411-O1 Rev D  210/215 Installation & Technical
17
ANNUNCIATORS
Annunciators are turned on to indicate that the display is in the mode corresponding to the
annunciator label or that the status indicated by the label is active. The annunciators flash on
and off to indicate that the indicator is waiting for input from the keypad for the mode indicated
by the flashing annunciator. Refer to Figure No. 9 and Figure No.10 for location of the
annunciators.
ZERO (210)
 (215)
This annunciator is turned on to indicate that the weight displayed is within +/- 1/4 division of
the center of zero.
 (STABLE)
This annunciator is turned on when the weight display is stable. When off, it means that the
change in successive weight samples is greater than the motion limits selected during setup.
NET
This annunciator is turned on to show that the displayed weight is the net weight (gross
weight less tare weight).
GROSS
This annunciator is turned on to show that gross weight is displayed. Gross weight will be
displayed when no tare weight is stored.
TARE
This annunciator is turned on to show that the displayed weight is the tare weight.
LO BAT
This annunciator is used with the battery operation and will turn ON to indicate the battery
has less than one hour useful life before recharging will be required. If continued use furthers
drains the battery, no change in operation will occur until just before the battery voltage drops
to a level where operation is affected. At this level, the indicator will automatically turn itself
off.
UNDER/PWC1 (210 Only)
This annunciator is used to signal that the displayed weight is less than the minimum value of
acceptable weight used in the Checkweigher feature. Note that this annunciator is active
only when the Checkweigher feature is enabled.
The PWC1 annunciator is turned on to indicate that the displayed weight is equal to or
greater than the weight value stored as preset number 1. Note that this annunciator is active
only when the Preset Weight Comparator feature has been enabled.
ACCEPT/PWC2 (210 Only)
This annunciator is used to signal that the displayed weight is within the acceptable weight
limits for the Checkweigher feature. That is, it is equal to or greater than the minimum
acceptable weight and equal to or less than the maximum acceptable weight. Note that this
annunciator is active only when the Checkweigher feature has been enabled.
The PWC2 annunciator is turned on to indicate that the displayed weight is equal to or
greater than the weight value stored as preset number 2. Note that this annunciator is active
only when the Preset Weight Comparator feature has been enabled.
18
8200-M411-O1 Rev D  210/215 Installation & Technical
ANNUNCIATORS
OVER/PWC3 (210 Only)
This annunciator is used to signal that the displayed weight is equal to or greater than the
minimum value of over weight used in the Checkweigher feature. Note that this annunciator
is active only when the Checkweigher feature has been enabled.
The PWC3 annunciator is turned on to indicate that the displayed weight is equal to or
greater than the weight value stored as preset number 3. Note that this annunciator is active
only when the Preset Weight Comparator feature has been enabled.
tn (210 Only)
This annunciator is located to the right of the weight display and is turned on to show that the
displayed weight unit is tons.
g
This annunciator is located to the right of the weight display and is used to indicate that the
displayed unit of weight measurement is grams.
lb
This annunciator is located to the left of the weight display and is turned on to show that the
displayed weight unit is pounds.
oz
This annunciator is located to the right of the weight display and is turned on to show that the
displayed weight unit is ounces.
kg
This annunciator is located to the left of the weight display and is used to indicate that the
displayed unit of weight measurement is kilograms.
t (210 Only)
This annunciator is located to the right of the weight display and is used to indicate that the
displayed unit of weight measurement is tonnes (metric tons).
PIECES (210)
COUNT (215)
This annunciator shows that the display is in the Count mode and the value displayed is the
count quantity and not weight.
TOTAL (215 Only)
This annunciator shows that the display is in the Count mode and that the value displayed is
the current contents (total) of the count accumulator.
8200-M411-O1 Rev D  210/215 Installation & Technical
19
SETUP AND CALIBRATION
Your Model 210/215 indicator has been
thoroughly tested and calibrated before
being shipped to you. If you received the
indicator attached to a scale, calibration
is not necessary. If the indicator is being
connected to a scale for the first time or
recalibration is necessary for other
reasons, proceed as indicated.
The calibration switch is located on a
bracket on the inside of the enclosure
rear panel. You may gain access to this
switch simply by removing the calibration
switch access screw on the rear panel.
Refer to Figure No. 11.
Access
Screw
Figure No. 11
During the setup and calibration process it is necessary to enter operational parameters via
the indicator’s keypad. Pressing the ENTER key without entering a new value will retain the
current setting and advance to the next prompt. To change a setting, enter a new value and
press the ENTER key. This will save the new value and advance to the next prompt.
Pressing the ASTERISK key will "backup" to the previous prompt.
DO NOT operate the keypad with pointed objects (pencils, pens, etc).
Damage to keypad resulting from this practice is NOT covered under warranty.
Enter Setup Mode
To enter the setup mode, with the indicator ON, insert a small screwdriver or other tool through
the calibration switch access hole on the rear panel. Press and release the calibration switch.
The menu SetUP will be displayed. Continue to press and release the switch to rotate
through the beginning point for entering the setup mode.
SEtUP
A-d
CAL
Sio
Print
F SPAn
Hi rES
LoCoUt
Setup Mode (starts at USA prompt)
Analog to Digital Filtering (starts at dFLt= prompt)
Calibration (starts at CAL1 prompt)
Serial Input/Output (starts at bAUd prompt)
Print Tab Settings (starts at POrt prompt)
Fine Span Adjustment
Display high-resolution weight mode
Key lock out function
If you press the ENTER key at the SetUP prompt, you may proceed through to the next
section (up to and including f SPAn ) by pressing the ENTER key.
IMPORTANT! Setup may be interrupted at any time. ALL data previously
entered and finalized with the ENTER key will be retained in the non-volatile
memory.
20
8200-M411-O1 Rev D  210/215 Installation & Technical
SETUP AND CALIBRATION, CONT.
Pressing the calibration switch at any prompt will return you to the SEtUP menu. To exit
setup, press the ASTERISK key with any of the above menu selections displayed or cycle
power at any time (press the ON/OFF key twice).
NOTE! With the exception of the SEtUP prompt, the prompts displayed for each section
are different if you push the calibration switch instead of pressing the ENTER key to
proceed through the section. For example, if you press the calibration switch with the
SEtUP displayed, the next prompt displayed will be A-d. If you step through the setup
prompts by pressing the ENTER key, the next prompt displayed will be A-d?. In addition,
at a prompt with the ? displayed, you must press the ENTER key, the 1/YES key then the
ENTER key again to proceed with that section. To skip the section and advance to the next
menu selection, press the ENTER key twice.
SEtUP
USA= (Domestic or International)
With SEtUP displayed, press the ENTER key. The display will change to USA=. Press the
ENTER key to show the current value. If the setting displayed is acceptable, press the ENTER
key again to save it. Otherwise, using the numeric keys, 0/NO or 1/YES, enter the new setting,
then press the ENTER key to save it.
USA=1 (Domestic)
Date = mm/dd/yy
Trl = no
Cap + 4% to OC
USA=0 (International)
Date = dd/mm/yy
Trl = yes
Cap + 9 grads to OC
PT printed with tare
Lamp test on power up
If you selected USA = 0 (International), an additional prompt, "PASS=" will be displayed.
If you selected USA = 1 (Domestic) proceed to LFt= (Legal For Trade).
PASS (Password Y/N)
The PASS (Password Y/N) prompt determines whether a password is required to enter Setup
and Calibration on indicators programmed for international use. Note that this prompt is only
displayed when USA = 0 (International) is selected.
With the display showing PASS, press the ENTER key to show the current value. If the setting
displayed is acceptable, press the ENTER key again to save it. Otherwise, using the numeric
keys, 0/NO or 1/YES, enter the new setting, then press the ENTER key to save it.
PASS (No)
Password protection is not needed.
Setup advances to the LFt= prompt
PASS (Yes)
Password protection is desired. The
next prompt will be PASS=
Press the ENTER key to see the current password value. If the password displayed is
acceptable, press the ENTER key again to save it. Otherwise, using the numeric keys enter
the new password (up to 6 digits) and then press the ENTER key to save it.
Password Operation
With the PASS prompt enabled (set to YES), anytime the operator tries to enter Setup, the
display will show the PASS= prompt requiring the operator to enter the correct password. If
the wrong password is entered the indicator displays ERROR momentarily and returns to the
weight mode. Note that the password is not displayed when the operator is entering it.
It is recommended to write the password down and store it in a secure location. If the
password is forgotten or lost and a change to the indicator setup is required, the indicator
must be reprogrammed. WARNING! Reprogramming the indicator will erase all the
contents of the Nov-Ram and memory.
8200-M411-O1 Rev D  210/215 Installation & Technical
21
SETUP AND CALIBRATION, CONT.
LFt= (Legal For Trade)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys, 0/NO or 1/YES, enter the
new setting, then press the ENTER key to save it.
LFt=1
Interval Settings (Int=) allowed
are: 1, 2, 5, 10 , 20, 50
LFt=0
Interval Setting (Int=) is
selectable from 1 to 99.
NOTE! When both LFt=1 and USA=1, the followings results occur:
Scale must have between 100 and 10,000 divisions
Tra = .5 or 0 to 3
Inhibit serial data during input
Disables COUNT key
Date = mm/dd/yy
Trl = no
Cap + 4% to OC
NOTE! When LFt=1 and USA=0, the followings results occur:
Uns = 1
Date = dd/mm/yy
Trl = yes
Cap + 9 grads to OC
PT printed with tare
Lamp test on power up
Unit1= (Weighing Unit 1)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys enter the new setting,
then press the ENTER key to save it. Allowable values are:
0 = none
1= tn (tons) – Only on 210
2= g (grams)
3 = lb (pounds)
4 = oz (ounces)
5 = kg (kilograms)
6 = tonnes (metric tons) – Only on 210
7 = lb/oz (pounds/ounces)
int= (Interval Setting)
Press the ENTER key to show the current value.
If LFt = 1 (Legal For Trade = YES), using the numeric keys enter the new setting, then
press the ENTER key to save it. Allowable values are: 1, 2, 5, 10, 20 or 50.
If LFt=0 (Legal For Trade = NO), using the numeric keys enter the new setting, then press
the ENTER key to save it. Allowable values are: 1 through 99.
In either case, if the setting displayed is acceptable, press the ENTER key again it.
dPP= (Decimal Point Setting)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys enter the new setting,
then press the ENTER key to save it. Allowable values are: 0, 1, 2 or 3.
0 = XXXXXX
1= XXXXX.X
22
2 = XXXX.XX
3 = XXX.XXX
8200-M411-O1 Rev D  210/215 Installation & Technical
SETUP AND CALIBRATION, CONT.
CAP= (Capacity)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys enter the new setting,
then press the ENTER key to save it. Allowable values are: 1 through 999,999.
NOTE! Capacity cannot exceed 999,999.
Unit2= (Weighing Unit 2)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys enter the new setting,
then press the ENTER key to save it. Allowable values are:
0 = none
1= tn (tons) – Only on 210
2= g (grams)
3 = lb (pounds)
4 = oz (ounces)
5 = kg (kilograms)
6 = tonnes (metric tons) – Only on 210
7 = lb/oz (pounds/ounces)
NOTE! The selection for Unit2 cannot be the same as Unit1. In addition,
dependent upon the selection for Unit1 and the interval and decimal point settings,
not all unit combinations are available.
trA= (Zero Tracking Range)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys enter the new setting,
then press the ENTER key to save it. Allowable values are: 0 (disables Zero Tracking), .5, or 1
through 9.
trL= (4% Zero Range)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys, 0/NO or 1/YES, enter the
new setting, then press the ENTER key to save it.
trL=1 (Yes)
4% of scale capacity
trL=0 (No)
Full capacity (no limit)
PUO= (Power-Up Zero Feature)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys, 0/NO or 1/YES, enter the
new setting, then press the ENTER key to save it.
PUO=1 (Yes)
Automatic Re-Zero on Power-Up
PUO=0 (No)
No Re-Zero on Power-Up
td = (12 or 24 Time Format)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, use the numeric keys to select the format (12 or
24 hour) of the Model 210 clock operation, then press the ENTER key to save it. Note that in
the 24 hour format, 12 is added to all times after noon, i.e. 3 PM would be 1500.
td = 12
12 hour clock (3PM displays 3:00)
td = 24
24 hour clock (3PM displays 15:00)
8200-M411-O1 Rev D  210/215 Installation & Technical
23
SETUP AND CALIBRATION, CONT.
d oUt = X, Y (Digital Output)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, use the numeric keys to select the X, Y values for
the digital output, then press the ENTER key to save it.
d out = X, Y
where:
X = State below cutoff (0 = LOW, 1 = High)
Y = Preset Number or Checkweigher Mode
0
1
2
3
11
12
13
4
14
5
=
=
=
=
=
=
=
=
=
=
Digital Output is disabled
Low State before cutoff with 1 active Preset
Low State before cutoff with 2 active Presets
Low State before cutoff with 3 active Presets
High state before cutoff with 1 active Preset
High state before cutoff with 2 active Presets
High state before cutoff with 3 active Presets
Low State before cutoff on Checkweigher Mode
High state before cutoff on Checkweigher Mode
Axle Weigher Operation Mode
P-bAL= (Preset Print-On-Balance)
With only one Preset selected (d OUt=1 or 11), an additional prompt P-bAL= (automatic
Print on Balance) will be displayed. If selected (P-bAL=YES), when the weight is above or
equals the preset value and all motion stops, weight will be printed (if a printer is attached).
Note that the weight must go below 50% of the preset value before another print operation can
be performed.
If the setting displayed is acceptable, press the ENTER key to save it. Otherwise, using the
numeric keys, 0/NO or 1/YES, enter the new setting, then press the ENTER key to save it.
P-bAL=1 (Yes)
Automatic Print on Balance Enabled
P-bAL=0 (No)
Automatic Print on Balance Disabled
P-bAL= (Checkweigher Print-On-Accept)
With Checkweigher selected (dOUt= 4 or 14), an additional prompt P bAL, Print on Balance,
(automatic print on accept) will be displayed. If selected (P-bAL=YES), when the scale weight
is stable and in the accept range of the checkweigher, the weight will be printed (if a printer is
attached).
If the setting displayed is acceptable, press the ENTER key to save it. Otherwise, using the
numeric keys, 0/NO or 1/YES, enter the new setting, then press the ENTER key to save it.
P-bAL=1 (Yes)
Automatic Print on Accept Enabled
P-bAL=0 (No)
Automatic Print on Accept Disabled
SLEEP= (Sleep Mode Feature)
The Sleep Mode feature conserves battery power when the indicator remains unused for a
selected period of time. With the feature enabled, the load cell excitation will be reduced and
the display will be blank. NOTE! The sleep mode only functions on the 215, when the
indicator is powered by the NiMH batteries and not by AC power.
Press the ENTER key to show the current status of this feature. If a number other than 0 is
shown, this feature is selected and the number shown corresponds to the number of minutes
of a stable zero weight reading before the indicator enters the sleep mode. If the setting
displayed is acceptable, press the ENTER key again to save it. Otherwise, use the numeric
keys to enter a new value (0 to 10) then press the ENTER key to store the new setting. Note
that entry of a 0 disables this feature.
24
8200-M411-O1 Rev D  210/215 Installation & Technical
SETUP AND CALIBRATION, CONT.
A oFF= (Auto Shutoff)
The Automatic Shutoff feature will automatically turn the indicator off (when it is not in use)
after a predetermined period of inactivity to prolong battery life. To turn the indicator back on
you must press the ON / OFF key.
Press the ENTER key to show the current status for this feature. A number other than 0
indicates that the auto shutoff feature is enabled and the displayed number corresponds to the
number of minutes of stable weight displayed before the indicator is turned off automatically.
Note that a 0 indicates the feature has been turned off. If the setting displayed is acceptable,
press the ENTER key again to save it. Otherwise, use the numeric keys to enter a new value
(0 to 10) then press the ENTER key to store the new setting.
CLtAr= (Clear Tare)
The Clear Tare feature allows the indicator to clear the Stored Tare weight when the Net
weight goes below a value greater than 1/2 the stored tare weight or goes below zero (a
negative net weight after display of a positive net weight). With this feature enabled, the
operator must re-set the tare after completion of a transaction when the load (container plus
item) is removed from the scale.
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys, 0/NO or 1/YES, enter the
new setting, then press the ENTER key to save it.
CLtAr=1 (Yes)
Automatically clears Stored Tare
when Net weight goes below zero
CLtAr=0 (No)
Stored Tare is not cleared when
Net weight goes below zero
id= (ID Prompt)
The id= (ID=) prompt enables an ID prompt before printing a ticket.
With the display showing id=, press the ENTER key to show the current value. If the setting
displayed is acceptable, press the ENTER key again to save it. Otherwise, using the numeric
keys, 0/NO or 1/YES, enter the new setting, then press the ENTER key to save it.
id=1 (Yes)
id= will be displayed when PRINT key
is pressed and printed on the ticket.
id=0 (No)
Normal print operation (no ID prompt)
will occur.
If you selected id=1 (Yes, ID Prompt), an additional prompt, "a clr=" will be displayed.
If you selected id=0 (No ID Prompt) proceed to A-d (A-d?) Analog to Digital Filtering.
A cLr= (Auto Clear ID)
The a clr= (Auto Clear ID) prompt determines whether the ID is automatically cleared after
printing the ticket. Note that it is only displayed when id= YES is selected.
With the display showing a clr=, press the ENTER key to show the current value. If the
setting displayed is acceptable, press the ENTER key again to save it. Otherwise, using the
numeric keys, 0/NO or 1/YES, enter the new setting, then press the ENTER key to save it.
A clr=1 (Yes)
Automatically clears the ID after the
ticket has printed.
a clr=0 (No)
ID is not cleared when ticket prints
and can be used for next transaction.
8200-M411-O1 Rev D  210/215 Installation & Technical
25
SETUP AND CALIBRATION, CONT.
A - d (A - d?) - Analog to Digital Filtering
dFLt= (Digital Filtering)
With A - d (A - d?) displayed, press the ENTER key. The display will change to dFLt=.
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key to save it. Otherwise, using the numeric keys enter the new setting, then
press the ENTER key to save it. Allowable values are: 0, 1, 2 or 3. Note, that if you select 3
(Custom Filtering) two additional prompts will be displayed.
dFLt=
0
1
2
3
Disabled – NO Filtering
MINIMAL FILTERING (sample rate = 2)
MODERATE FILTERING (sample rate = 1)
CUSTOM FILTERING
NOTE! The prompts, F= (Filter Level) and b= (Break Range) will only be displayed if you
selected 3 (Custom Filtering) for the dFLt= (Digital Filtering) prompt.
F= (Filter Level)
Press the ENTER key to show the current setting for the filter level. The filter level is a number
from 1 to 99 that corresponds to the level of filtering with 99 being the greatest filtering and 1
the least. To accept the value displayed, press the ENTER key, otherwise, use the numeric
keys to enter a new value then press the ENTER key to save it.
b= (Break Range)
Press the ENTER key to show the current setting for the break range. The break range is a
number from 1 to 255 that corresponds to the number of division change to break out of the
filtering. Press the ENTER key to keep the displayed value or use the numeric keys to enter a
new value and press the ENTER key to save the new setting. Note that entry of a 0 disables
this feature.
Sr= (Sample Rate)
Press the ENTER key to show the current setting for the sample rate. The value displayed is
the sample rate in samples per second. Press the ENTER key to save the displayed value or
use the numeric keys to enter a new value (1 to 100) and press the ENTER key to save it.
UnS= (Motion Range)
Press the ENTER key to view the current setting for the range of motion detection. If the
displayed value is acceptable, press the ENTER key to save it. Otherwise, use the numeric
keys to enter the new range (the number of divisions of change permitted before indicating
unstable), then press the ENTER key to save the new setting. Allowable range values are: 0
through 99 divisions.
SC= (Stable Count)
Press the ENTER key to view the current setting for the number of consecutive stable weight
readings before indicating stable weight. This helps filter weight readings for stability for use
with Auto Print on Balance, or and anything trying to capture stable weight. If the displayed
value is acceptable, press the ENTER key to save it. Otherwise, use the numeric keys to enter
a new value and press the ENTER key to save the new setting. Allowable values for the
stable count are: 3 through 255.
26
8200-M411-O1 Rev D  210/215 Installation & Technical
SETUP AND CALIBRATION, CONT.
FILTER SETTING RECOMMENDATIONS
Non Critical Sample Rate
If the sample rate is not critical, as in static weighing, set dFLt= to “0” (no filtering),
dFLt= “1” (F=6, b=12, Sr= 2/Sec), or dFLt= “2” (F=6, b=8, Sr= 1/Sec).
Critical Sample Rate
If the sample rate is critical, as in a filling operation, use the Custom Filtering (set dFLt= to
“3”).
1. Sr= SAMPLE RATE (1 to 50 samples/second) determination:
Set the sample rate as close as possible to produce a display graduation change for
every graduation of material added to the scale.
Material Flow Rate (lbs/second) =
Resolution
EXAMPLE:
100lbs/sec
= 10s/s = Sr
10lbs
2. b= BREAK RANGE (1 to 255 graduations) determination:
Turn the filtering off by setting the dFLt= setting to “0”. Operate the system as it will be
normally used and, by observation, determine the number of grads of instability that
needs to be filtered out. Set the break range (b=) to that value.
Weight Change
= b
Graduation Value
EXAMPLE: 20,000 x 10lb capacity scale with 800lb variation in the weight
display.
800
= b = 80
10
3. F= FILTER SETTING (1 to 99) determination: Set to desired results.
4. If stability is unacceptable with any setting of F=, reduce the sample rate and/or
increase the break range, b= setting for increased filtering.
8200-M411-O1 Rev D  210/215 Installation & Technical
27
SETUP AND CALIBRATION, CONT.
CAL (CAL?) - Calibration
With CAL (CAL?) displayed, press the ENTER key. The display will change to show the
current setting No. If calibration is desired, press the 1/YES key, then press the ENTER key to
continue to the CAL1= setting, otherwise press the ENTER key to advance to the Sio menu.
CALIBRATION MODES
The 210/215 indicators have five modes that can be used to perform calibration. Three of the
modes require a test load or test weights, one requires the scale to be empty (and at zero) and
the last uses the calibration “C” numbers from a previous calibration. The modes are as
follows:
1. Dual-Point with Zero (First Zero)
This is a standard calibration method requiring one weight, an empty scale and has one
conversion factor. This method uses two calibration points (CAL1= and CAL2=) to
establish a zero (no load) calibration value and to span the indicator. The two points
correspond to zero weight and the test load or test weight and can be applied in any order.
This method should be used for first-time calibration and complete recalibration.
2. Dual-Point without Zero (False Zero)
This calibration method requires one test weight and establishes a new conversion factor
only. It is used to establish a false (temporary zero) zero without affecting the zero
calibration value stored during the last calibration. This is particularly useful in tank
weighing applications, where it may be impractical or impossible to completely empty the
tank. This method uses two calibration points, CAL1= and CAL2=. The value of the test
weight is entered when CAL1= is displayed and the NET/GROSS key is pressed when
CAL2= is displayed.
3. Single-Point for Span Only (Last Zero)
This calibration method requires one test weight and establishes a new conversion factor
(span) without affecting the zero calibration value stored during the last calibration. This
minimizes placing and removing test weights and is especially useful when checking high
capacity scales. This method uses two calibration points, CAL1= and CAL2=. The value
of the test weight is entered when CAL1= is displayed and the ZERO key is pressed when
CAL2= is displayed.
4. Single-Point for Zero Only (Only Zero)
This calibration method requires no test weight, an empty scale and establishes a new
zero without affecting the conversion factor (span). This is useful to regain the full range of
zero limit when the dead load of the scale has changed. This would occur for example, if a
guard rail has been added to the scale platform. This method uses two calibration points,
CAL1= and CAL2=. The ENTER key is pressed when CAL1= is displayed and the ZERO
key is pressed when CAL2= is displayed.
5. Calibration “C” Numbers
The calibration “C” numbers (C1, C2, C3 and C4) are displayed only during the Test mode
operation and are shown at the end of the test. Each number is displayed for
approximately 4 seconds, allowing you to record them. These numbers correspond to the
calibration setting of the indicator. The numbers may be up to three digits in length. By
recording these numbers you will be able to return the indicator to its present calibration
settings without using test weights simply by entering the “C” numbers. Refer to the
Calibration "C" Number section of this manual for instructions on viewing the “C” numbers.
28
8200-M411-O1 Rev D  210/215 Installation & Technical
SETUP AND CALIBRATION, CONT.
Dual-Point with Zero (First Zero) Calibration
CAL1= – First Calibration Weight
The display will show CAL1=0. This is the first of two calibration weights. This weight
could be ZERO (NO LOAD) or the TEST WEIGHTS / TEST LOAD.
•
If the first calibration weight is to be ZERO (NO LOAD), press the ENTER key.
•
If the first calibration weight is to be the TEST WEIGHTS / TEST LOAD, use the
numeric keys to input the value of the calibrated test weights. NOTE! When entering
values for CAL1=, the digits start displaying on the right side of the display and
proceed to the left. When large values are used (more than 3 digits), the CAL1=
prompt will automatically scroll off the left side of the display to show the additional
digits on the right as they are entered.
•
Place the weights on the scale platform, then press the ENTER key.
•
Starting at the left and proceeding right, a series of dashes will appear on the display.
The dashes will stay on the display momentarily, then disappear, after which the display
will show: CAL2=.
CAL2= - Second Calibration Weight
The display will show CAL2=0. This is the second of two calibration weights. This
weight could be ZERO (NO LOAD) or the TEST WEIGHTS / TEST LOAD.
•
If the second calibration weight is to be ZERO (NO LOAD), press the ENTER key.
•
If the second calibration weight is to be the TEST WEIGHTS / TEST LOAD, use the
numeric keys to input the value of the calibrated test weights. NOTE! When entering
values for CAL2=, the digits start displaying on the right side of the display and
proceed to the left. When large values are used (more than 3 digits), the CAL2=
prompt will automatically scroll off the left side of the display to show the additional
digits on the right as they are entered.
•
Place the weights on the scale platform, then press the ENTER key.
•
Starting at the left and proceeding right, a series of dashes will appear on the display.
The dashes will stay on the display momentarily, then disappear, after which the display
will show: CAL3=.
CAL3= - Last Calibration Weight
The display will show CAL3=0. This weight is not used. Press the ENTER key to skip
CAL3= and advance to Sio?.
8200-M411-O1 Rev D  210/215 Installation & Technical
29
SETUP AND CALIBRATION, CONT.
Dual-Point without Zero (False Zero) Calibration
CAL1= – First Calibration Weight
The display will show CAL1=0. This is the first of two calibration steps. This weight is
the TEST WEIGHTS / TEST LOAD.
•
Place the weights on the scale platform.
•
Using the numeric keys, input the value of the calibrated test weights / test load, then
press the ENTER key. NOTE! When entering values for CAL1=, the digits start
displaying on the right side of the display and proceed to the left. When large values
are used (more than 3 digits), the CAL1= prompt will automatically scroll off the left
side of the display to show the additional digits on the right as they are entered.
•
Starting at the left and proceeding right, a series of dashes will appear on the display.
The dashes will stay on the display momentarily, then disappear, after which the
display will show: CAL2=.
CAL2= - Second Calibration Weight
The display will show CAL2=0. This is the second of two calibration steps.
•
Remove the weights on the scale platform, then press the NET/GROSS key.
•
Starting at the left and proceeding right, a series of dashes will appear on the display.
The dashes will stay on the display momentarily, then disappear, after which the display
will show: Sio?.
Single-Point for Span Only (Last Zero) Calibration
CAL1= – First Calibration Weight
The display will show CAL1=0. This is the first of two calibration steps. This weight is
the TEST WEIGHTS / TEST LOAD.
•
Zero the scale, then place the weights on the scale platform.
•
Using the numeric keys, input the value of the calibrated test weights / test load, then
press the ENTER key. NOTE! When entering values for CAL1=, the digits start
displaying on the right side of the display and proceed to the left. When large values
are used (more than 3 digits), the CAL1= prompt will automatically scroll off the left
side of the display to show the additional digits on the right as they are entered.
•
Starting at the left and proceeding right, a series of dashes will appear on the display.
The dashes will stay on the display momentarily, then disappear, after which the
display will show: CAL2=.
CAL2= - Second Calibration Weight
The display will show CAL2=0. This is the second of two calibration steps.
30
•
Remove the weights on the scale platform, and then press the ZERO key.
•
The display will advance to Sio?.
8200-M411-O1 Rev D  210/215 Installation & Technical
SETUP AND CALIBRATION, CONT.
Single-Point for Zero Only (Only Zero) Calibration
CAL1= – First Calibration Weight
The display will show CAL1=0. This is the first of two calibration steps.
•
Insure the scale is empty.
•
Press the ENTER key.
•
Starting at the left and proceeding right, a series of dashes will appear on the display.
The dashes will stay on the display momentarily, then disappear, after which the
display will show: CAL2=.
CAL2= - Second Calibration Weight
The display will show CAL2=0. This is the second of two calibration steps.
•
Press the ZERO key.
•
The display will advance to Sio?.
Calibration “C” Numbers
1.
2.
3.
4.
5.
With CAL1= displayed, press the "diamond T” TARE key.
At the C1= prompt, press the ENTER key to show the current value of the C1 number.
If the C1= number displayed is acceptable, press the ENTER key again to save it.
Otherwise, use the numeric keys to enter a new C1= number, then press the ENTER key.
Repeat steps 2 through 4 for C2=, C3= and C4=.
NOTE! If any components have been changed that affect calibration and/or
your scale is used in a commercial application and must be "Legal for Trade"
you cannot use the “C” numbers to re-calibrate.
8200-M411-O1 Rev D  210/215 Installation & Technical
31
SETUP AND CALIBRATION, CONT.
Sio (Sio?) - Serial Input/Output
With Sio (Sio?) displayed, press the ENTER key. The display will change to show the
current setting no. To skip configuring the Sio (serial input/output) and proceed to the
Print? menu, press the ENTER key again. To configure the Sio, press the numeric key
1/YES (display will change to YES) and then press the ENTER key. After pressing the ENTER
key, the display will change to bAud=.
bAUd= (Serial Port Baud Rate)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, use the numeric keys to enter a new baud rate for
the serial ports, then press the ENTER key to save it. Allowable values are:
12 = 1200 Baud
96 = 9600 Baud
76 = 76.8k Baud
24 = 2400 Baud
19 = 19.2k Baud
48 = 4800 Baud
38 = 38.4k Baud
Prty= (Serial Port Parity)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys enter the new setting,
then press the ENTER key to save it. Allowable values are: 0, 1, or 2.
0 = NONE (No Parity)
1 = Odd Parity
2 = Even Parity
bitS= (Serial Port Data Bits)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys enter the new setting,
then press the ENTER key to save it. Allowable values are: 7 or 8.
StoP= (Serial Port Stop Bits)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys enter the new setting,
then press the ENTER key to save it. Allowable values are: 1 or 2.
Cont1= (Continuous Output Serial Port 1)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys, 0/NO or 1/YES, enter the
new setting, then press the ENTER key to save it.
Cont1= YES
Continuous Output
Cont1= no
No Continuous Output
If Cont1= YES (Continuous Output) is selected, an additional prompt, tYPE=
will be displayed.
If Cont1= no (No Continuous Output) is selected, proceed to the Weight On
Demand section.
tyPE= (Continuous Output Format)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys enter the new setting,
then press the ENTER key to save it. Allowable values are:
0 = SMA
1 = SB-400
2 = SB-200
32
3 = Rice Lake IQ355
4 = AnDFV
5 = WI110
6 = Number
7 = Toledo Short
8 = SB500 with Traffic Light
8200-M411-O1 Rev D  210/215 Installation & Technical
SETUP AND CALIBRATION, CONT.
If SMA is selected, the data will be transmitted in the following format:
<lf><s><r><n><m><f><xxxxxx.xxx><uuu><cr>
Where:
lf =
s=
Line Feed
Flags
r=
n=
m=
f=
xxxxxx.xxx =
uuu =
cr =
Range
Mode
Motion
Custom
Weight
Units
Carriage Return
Z= center of Zero, O = Overcap, E = zero Error,
e = weight not currently being displayed
1, 2, 3, ...
G = Gross, T = Tare, N = Net
M = Motion, " "(blank) = no motion
Custom flag
Six digits with decimal point
ton, lb , l/o, oz , t , kg , g
(hex 0D)
If SB-400* or Computer is selected, the data will be transmitted in the following format:
<s><xxxxxx><d><uu><m><cc><cr>
Where:
*
s=
xxxxxx.xxx =
d=
uu =
m=
cc =
Sign
Weight
Decimal point
Units
Mode
Weight Status
cr =
Carriage Return
"-" = negative, " " (blank) = positive
Six digits
Added to string if enabled in setup
tn, lb, l/o, oz, t, kg, g
G = Gross, N = Net
OC = overcap
CZ = center of zero
MO = motion
ee = weight not currently being displayed
(hex 0D)
The SB-80, SB-300 (multiple displays not supported) and WinVRS use the SB-400 format.
If SB-200 is selected, the data will be transmitted in the following format:
<cr><s><xxxxxx><d><c><uu><m> ETX
Where:
cr =
s=
xxxxxx.xxx =
d=
c=
Carriage Return
Sign
Weight
Decimal point
status
(hex 0D)
"-" = negative, " " (blank) = positive
(with leading zeros)
Embedded into weight (after weight dpp=0)
m = motion
o = overcap
e = weight not currently being displayed
uu =
m=
ETX =
Units
Mode
End of TeXt
tn, lb, l/o, oz, t, kg, g
G = Gross, N = Net
(hex 03) MUST terminate ALL serial commands
If Rice Lake IQ355 is selected, the data will be transmitted in the following format:
<stx><s>xxxxxxx<u><m><s><cr><lf>
If AnDFV is selected, the data will be transmitted in the following format:
<hdr1>,xxxxx<uu><cr><lf>
8200-M411-O1 Rev D  210/215 Installation & Technical
33
SETUP AND CALIBRATION, CONT.
If WI110 is selected, the data will be transmitted in the following format:
<m><sp><s>xxxxx<sp><uu><cr><lf>
If number only is selected, the data will be transmitted in the following format:
xxxxxx<cr><lf>
If Toledo Short is selected, the data will be transmitted in the following format:
<stx><swa><swb><swc>xxxxxx<cr><sum>
Weight On Demand
If continuous output has not been selected for Serial Port 1 (Cont1=NO), the 210/215 indicator
will respond to a weight request (ENQ).
The host device (computer) sends:
ENQ - (hex 05)
The 210/215 will respond:
<s><xxxxxx><d><uu><m><cc><cr>
Where:
s=
xxxxxx.xxx =
d=
uu =
m=
cc =
Sign
Weight
Decimal point
Units
Mode
Weight Status
cr =
Carriage Return
"-" = negative, " " (blank) = positive
Six digits
Added to string if enabled in setup
tn, lb, l/o, oz, t, kg, g
G = Gross, N = Net
OC = overcap
CZ = center of zero
MO = motion
ee = weight not currently being displayed
(hex 0D)
NOTE! The Weight On Demand function is not available for Serial Port 2.
Cont2= (Continuous Output Serial Port 2)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys, 0/NO or 1/YES, enter the
new setting and then press the ENTER key to save it.
Cont2= YES
Continuous Output
Cont2= no
No Continuous Output
If Cont2= YES (Continuous Output) is selected, an additional prompt, tYPE= will be
displayed.
tyPE= (Continuous Output Format)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, using the numeric keys enter the new setting,
then press the ENTER key to save it. Allowable values are:
0 = SMA
1 = SB-400
2 = SB-200
3 = Rice Lake IQ355
4 = AnDFV
5 = WI110
6 = Number
7 = Toledo Short
8 = SB500 with Traffic Light
NOTE! See Continuous Output Serial Port 1, tyPE= for description of output formats.
34
8200-M411-O1 Rev D  210/215 Installation & Technical
SETUP AND CALIBRATION, CONT.
tHrs= (Threshold Weight)
Press the ENTER key to show the current value. If the setting displayed is acceptable, press
the ENTER key again to save it. Otherwise, use the numeric keys to enter a new value for the
threshold weight or enter a zero (0) to disable the traffic light and then press the ENTER key to
save it.
The threshold weight is used to automatically toggle between the Red and Green lights.
• When the scale gross weight is less than the threshold weight, the Green light will be on,
otherwise the Red light will turn on and stay on until the weight goes below the threshold
weight or a ticket is printed.
• When a ticket is printed, the Green light will turn on and stay on until the scale gross weight
goes below and back above the threshold weight and then the Red light will turn on.
• NOTE! If you enter a zero (0) for the threshold weight (THRS=0), the traffic light feature
will be disabled (turned off).
8200-M411-O1 Rev D  210/215 Installation & Technical
35
SETUP AND CALIBRATION, CONT.
Print (Print?) - Print Tab Settings
With Print (Print?) displayed, press the ENTER key. The display will change to show the
current setting no. To skip configuring the Print Tab Settings and proceed to the FSPAn?
menu, press the ENTER key again. To configure Print Tab Settings, press the numeric key
1/YES (display will change to YES) and then the ENTER key. After pressing the ENTER key
the display will change to Port=.
The general format for the input is A = YY.XX where A is the
character identifying the data printed, YY is the number of lines
down and XX is the number of spaces to the right.
NOTE! Enter 00 in either the YY or XX location to
disable the data from printing.
Port= (Select Port for Printer)
Press the ENTER key to show the current value. If the setting
displayed is acceptable, press the ENTER key again to save it.
Otherwise, use the numeric keys to enter a new setting and then press the ENTER key to save
it. Allowable values are: 1 or 2.
NOTE! Although either port can be used for the printer port, it is recommended to
use the bi-directional port 1 with a bi-directional cable.
HoUr= (Time Print Location)
Press the ENTER key to show the current setting for the location of time printing. If the setting
displayed is acceptable, press the ENTER key again to save it. Otherwise, use the numeric
keys to enter a new location and then press ENTER to save it.
dAtE= (Date Print Location)
Press the ENTER key to show the current setting for the location of date printing. If the setting
displayed is acceptable, press the ENTER key again to save it. Otherwise, use the numeric
keys to enter a new location and then press ENTER to save it.
id= (ID Prompt Print Location)
Press the ENTER key to show the current setting for the location of ID prompt printing. If the
setting displayed is acceptable, press the ENTER key again to save it. Otherwise, use the
numeric keys to enter a new location and then press ENTER to save it.
CnC n= (Consecutive Number Print Location)
Press the ENTER key to show the current setting for the location of consecutive number
printing. If the setting displayed is acceptable, press the ENTER key again to save it.
Otherwise, use the numeric keys to enter a new location and then press ENTER to save it.
GroSS= (Gross Weight Print Location)
Press the ENTER key to show the current setting for the location of Gross weight printing. If
the setting displayed is acceptable, press the ENTER key again to save it. Otherwise, use the
numeric keys to enter a new location and then press ENTER to save it.
tArE= (Tare Weight Print Location)
Press the ENTER key to show the current setting for the location of Tare weight printing. If the
setting displayed is acceptable, press the ENTER key again to save it. Otherwise, use the
numeric keys to enter a new location and then press ENTER to save it.
36
8200-M411-O1 Rev D  210/215 Installation & Technical
SETUP AND CALIBRATION, CONT.
nEt= (Net Weight Print Location)
Press the ENTER key to show the current setting for the location of Net weight printing. If the
setting displayed is acceptable, press the ENTER key again to save it. Otherwise, use the
numeric keys to enter a new location and then press ENTER to save it.
G ACC= (Gross Weight Accumulator Print Location)
Press the ENTER key to show the current setting for the location of Gross weight accumulator
printing. If the setting displayed is acceptable, press the ENTER key again to save it.
Otherwise, use the numeric keys to enter a new location and then press ENTER to save it.
n ACC= (Net Weight Accumulator Print Location)
Press the ENTER key to show the current setting for the location of Net weight accumulator
printing. If the setting displayed is acceptable, press the ENTER key again to save it.
Otherwise, use the numeric keys to enter a new location and then press ENTER to save it.
CoUnt= (Count "number of pieces on the scale" Print Location)
Press the ENTER key to show the current setting for the location of Count (number of pieces
on scale) printing. If the setting displayed is acceptable, press the ENTER key again to save it.
Otherwise, use the numeric keys to enter a new location and then press ENTER to save it.
EACH= (Piece Weight Print Location)
Press the ENTER key to show the current setting for the location of Piece weight printing. If
the setting displayed is acceptable, press the ENTER key again to save it. Otherwise, use the
numeric keys to enter a new location and then press ENTER to save it.
CrLF= (Carriage Return Line Feed) - Data Format Termination
Data transmitted from the serial I/O port can be terminated with a single carriage return and
either no line feed or a single line feed command. Press the ENTER key to view the current
setting. A YES on the display means the data will be terminated with a carriage return AND a
line feed while a no on the display means the data will be terminated with a single carriage
return only.
If the setting displayed is acceptable, press the ENTER key again to save it. Otherwise, using
the numeric keys, 0/NO or 1/YES, enter the new setting, then press the ENTER key to save it.
EoP= (End-Of-Print Line Feeds)
At the end of a data transmission to a printer, the indicator can transmit a pre-selected number
of line feed commands to space the paper in the printer to the desired position for withdrawal
or for the next print.
Press the ENTER key to view the current setting. If the displayed value is acceptable, press
the ENTER key to save it. Otherwise, use the numeric keys to enter the new the number of
End-Of-Print linefeeds, then press the ENTER key to save the new setting. Allowable values
are: 0 through 99.
8200-M411-O1 Rev D  210/215 Installation & Technical
37
SETUP AND CALIBRATION, CONT.
F SPAn (FSPAn?) - Fine Span Adjustment
NOTE! The FSPAn and Hi rES modes require a load of 10% of Capacity be on
the scale before adjustments can be made.
With the F SPAn? prompt displayed after pressing the ENTER key at the last Print prompt:
With FSPAn? displayed, press the ENTER key. The display will change to show the current
setting no. To skip the Fine Span Adjustment and return to the SEtUP menu, press the
ENTER key again. To perform the Fine Span Adjustment, place a calibrated test weight on
the scale, press the numeric key 1/YES (display will change to YES) and then the ENTER
key.
After pressing the ENTER key, the display will change to show the amount of the test weight
and the annunciators will alternately flash off and on i.e. (all ON, weighing unit off, then all
OFF, weighing unit ON). Press the 1/YES to increase the span OR press the 0/NO key to
decrease the span. Press the ASTERISK key to return to the previous prompt or press the
ENTER key to exit FSPAn? and return to the SEtUP menu.
With the F SPAn prompt displayed after pressing the Calibration switch:
With F SPAn displayed, place a calibrated test weight on the scale and press the ENTER
key. After pressing the ENTER key, the display will change to show the amount of the test
weight and the annunciators will alternately flash off and on (all ON, weighing unit off, then
all OFF, weighing unit ON). Press the 1/YES to increase the span OR press the 0/NO key
to decrease the span. Press the ASTERISK key to return to the previous prompt or press
the ENTER key to exit F SPAn and return to the SEtUP menu.
Hi rES - Display High Resolution Weight
With Hi rES on the display, pressing the ENTER key will show the active weight in "high
resolution" mode (in 1/10 interval). Press the PRINT key to print the weight (followed by the
text TEST) via the selected printer output port enabled during setup and calibration. Press the
ENTER key to return to the Hi rE S prompt. To exit the Hi rE S mode, press the
calibration switch or cycle power (press the ON/OFF key twice).
LoCoUt - Key Lock Out Function
With LoCoUt on the display, pressing any key will display LoCd (locked) or UnLoCd
(unlocked) for the current key state. Pressing a locked key during normal operation will results
in a 1/2 second display LoCd and the key will be ignored. To exit the LoCoUt function, press
the calibration switch or cycle power (press the ON/OFF key twice).
NOTE! The menu selections Hi rES and LoCoUt can only be selected using
the calibration switch.
38
8200-M411-O1 Rev D  210/215 Installation & Technical
SETUP REVIEW
The 210/215 indicators allow several operational parameters to be reviewed and changed
without breaking the calibration seal. These operational parameters are:
Power Up Zero Reset Enable/Disable
Time Format
Digital Output Control Enable/Disable
Sleep Mode Feature Enable/Disable
Auto Shutoff Feature Enable/Disable
Serial Input / Output Configuration
Baud Rate
Parity
Number of Data Bits
Number of Stop Bits
Continuous Output Port 1
Continuous Output Format
Continuous Output Port 2
Continuous Output Format
Print Tab Settings
Printer Port Selection
Time
Date
Consecutive Number
Gross Weight
Tare Weight
Net Weight
Gross Weight Accumulator
Net Weight Accumulator
Count
Piece Weight
To enable the Setup Review feature, with the indicator ON:
1. Press the ASTERISK key. The indicator will respond by showing the FUnCt=
(Function) prompt and alternately flashing off and on (all ON, weighing unit off, then all
OFF, weighing unit ON) the annunciators.
2. Press the ZERO/REVIEW key. The display will change to the prompt for the selection of
power-up zeroing (PUO=).
3. Using the same procedure as described in the Setup and Calibration section of this
manual, make the required changes.
4. Press the ASTERISK key to return to the previous prompt.
5. To exit Setup Review, press the ENTER key to step the remaining prompts OR at
anytime, cycle the power (press the ON/OFF key twice).
CALIBRATION “C” NUMBERS
The “C” numbers are displayed only during the Test mode operation by pressing the
ASTERISK key then the UNITS/TEST key. The "C" numbers are shown at the end of the test
operation and each number is displayed for approximately 4 seconds, allowing you to record
them. Each number may be up to three (3) digits in length. By recording these numbers you
will be able to return the indicator to its present calibration settings without using test weights
simply by entering the “C” numbers. Refer to the Setup and Calibration, CAL section of this
manual for instructions on using the "C" numbers.
If any components have been changed that affect calibration and/or your scale
is used in a commercial application and must be "Legal for Trade" you cannot
use "C" numbers to re-calibrate.
8200-M411-O1 Rev D  210/215 Installation & Technical
39
ACCUMULATORS
To view the NET accumulator:
1. Press the ASTERISK key then the NET/GROSS key.
2. Press the ASTERISK key to return to normal operation.
To print the NET accumulator:
1. Press the ASTERISK key, the NET/GROSS key, then the PRINT key
2. The indicator will return to normal operation when printing has been completed.
To clear (zero) the NET accumulator:
1. Press the ASTERISK key, the NET/GROSS key, then the ZERO key
2. Press the ASTERISK key to return to normal operation.
To view the Gross accumulator:
1. Press the ASTERISK key then the NET/GROSS key twice.
2. Press the ASTERISK key to return to normal operation.
To print the Gross accumulator:
1. Press the ASTERISK key, the NET/GROSS key twice, then the PRINT key
2. The indicator will return to normal operation when printing has been completed.
To clear (zero) the Gross accumulator:
1. Press the ASTERISK key, the NET/GROSS key twice, then the ZERO key
2. Press the ASTERISK key to return to normal operation.
To view the Count accumulator:
1. Press the ASTERISK key then the COUNT/SAMPLE key.
2. Press the ASTERISK key to return to normal operation.
To print the Count accumulator:
1. Press the ASTERISK key, the COUNT/SAMPLE key, then the PRINT key
2. The indicator will return to normal operation when printing has been completed.
To clear (zero) the Count accumulator:
1. Press the ASTERISK key, the COUNT/SAMPLE key, then the ZERO key
2. Press the ASTERISK key to return to normal operation.
NOTES FOR THE MODEL 215 ONLY
1. If LFt (Legal For Trade) is enabled, the scale must be at Gross weight zero to review
the accumulators.
2. The scale must return to Gross weight zero between accumulations.
3. When viewing the Gross or Net accumulators, the display will toggle between the total
accumulator and the total count for the selected accumulator.
40
8200-M411-O1 Rev D  210/215 Installation & Technical
BEFORE YOU CALL FOR SERVICE
The 210/215 indicators have been designed to provide you with years of trouble-free
operation. However, should you experience a problem, please refer to the troubleshooting
guide below before you call for service. The following describes several types of symptoms
along with suggested remedies.
PROBLEM
Display does not turn on
POSSIBLE SOLUTIONS
AC operation:
Is the AC power cord fully inserted into the wall
receptacle? Check wall receptacle for proper AC power.
Try another electrical appliance in the same receptacle,
does it work? Check the circuit breaker. Has there been
power failure?
Battery operation:
Check if battery is installed and correctly. Is battery
discharged - replace or recharge.
NOTE! The battery tray (with or without batteries)
must be installed for the Model 215 to function.
Incorrect weight displayed
Has the indicator been calibrated? Insure that the scale
platform isn't touching an adjacent object. Check the load
cell connector wiring. If using four (4) wire load cells,
insure the sense lead jumpers (J4 & J5) are installed.
Have proper operation procedures been followed?
Indicator will not
display weight
Refer to Error Codes section and make certain that the
oCAP message is not displayed. If so, and scale is not
loaded, perform the calibration sequence.
The printer prints but does
not use the Print Tab Settings
or prints a test ticket
The print tab setting or visual ticket format must be
selected prior to beginning the weighing operation or just
prior to printing the ticket.
To select the ticket format prior to beginning the weighing
operation:
1. Press the ASTERISK key then the PRINT key. The
display will change to the “Prt=”.
2. Press the ENTER key to show the current value.
3. If the value displayed is acceptable, press the ENTER
key again to save it.
4. If the displayed value is incorrect (or another ticket
format is desired), use the numeric keys to enter the
new value, then press the ENTER key to save it.
To select the ticket format just prior to printing the ticket:
1. Press the desired format number.
2. Pressing the PRINT key.
Allowable values for ticket formats are:
0 = print tab settings
1 = visual ticket format 1
2 = visual ticket format 2
NOTE! When a print format is selected (by either
method), it will remain active until changed by the
operator.
8200-M411-O1 Rev D  210/215 Installation & Technical
41
ERROR CODES
The 210/215 indicators are equipped with software that indicates when an error in the
operation takes place. The following lists the error codes displayed by the 210/215 along with
their meaning. Should you encounter an error code, please refer to this list for the cause.
CALbtn (Calibration button)
CALbtn will be displayed (until the condition changes), on power-up if the calibration switch
is pressed in by the operator, the calibration access screw is the wrong length and is
depressing the switch, the switch is disconnected from the PC board, or the switch is
defective.
CORRECTIVE ACTION: Release the switch. Insure correct screw (#10 x ½ Stainless Steel
fillister head) was installed for the calibration access screw. Referring to Figure No. 6, make
sure calibration switch cable is plugged into P7 on the PC board. Replace calibration switch
assembly. Consult your scale service provider.
ConFiG (Configuration)
E2PROM checksum failure. Indicates improper stored calibration data, calibration is
necessary.
CORRECTIVE ACTION: Recalibrate with calibrated test weight.
Error (Error)
An invalid keypad entry was attempted:
A.
B.
C.
D.
PRINT key pressed with a negative weight.
TARE key pressed to enter a push button tare value of a negative value.
ENTER key pressed to enter a tare weight value that exceeds the scale capacity.
ENTER key pressed to enter a tare weight value that is inconsistent with the scale
division value (i.e. attempt to enter a tare of 123 with scale divisions of 5).
E. ZERO key pressed when the gross weight is outside the scale zero weight range.
F. lb/kg key pressed to change to kg when the kg tare weight value exceeds 4 digits in
length.
CORRECTIVE ACTION: Determine which of the reasons for the error display is applicable
and take the appropriate corrective action.
ErrAh (Error Analog high)
1. The load cell input is above the range of the indicator.
CORRECTIVE ACTION: Check for improper load cell wiring, excessive load, and for
output of 1 to 40mV.
2. Load cell or circuit failure.
CORRECTIVE ACTION: Consult your scale service provider.
ErrAL (Error Analog Low)
1. The load cell input is below the range of the indicator.
CORRECTIVE ACTION: Check for improper load cell wiring and for output of 1 to 40mV.
2. Load cell or circuit failure.
CORRECTIVE ACTION: Consult your scale service provider.
Err1 (Error 1)
A program checksum mismatch has been detected.
CORRECTIVE ACTION: Consult your scale service provider.
Err3 (Error 3)
Internal RAM failure.
CORRECTIVE ACTION: Consult your scale service provider.
42
8200-M411-O1 Rev D  210/215 Installation & Technical
ERROR CODES, CONT.
HuH? (HuH?)
UNITS key pressed in an attempt to perform a unit conversion that is not allowed.
CORRECTIVE ACTION: Determine the reason for the error display and take the
appropriate corrective action.
notArE (no tarE)
NET key pressed with no stored tare weight value.
CORRECTIVE ACTION: Determine the reason for the error display and take the
appropriate corrective action.
oCAP (over Capacity)
The load on the scale exceeds the scale capacity plus nine (9) divisions.
CORRECTIVE ACTION: Remove the over capacity load from the scale platform. May
indicate miscalibration.
-oF- (overflow)
The indicator is attempting to display a positive number greater than six (6) digits in length
or a negative number of more than five (5) digits.
CORRECTIVE ACTION: Return to Gross Weight mode and review Tare value. May
indicate miscalibration.
toobiG (too big)
UNITS key pressed in an attempt to perform a unit conversion where the interval would
have been greater than 50.
CORRECTIVE ACTION: Determine the reason for the error display and take the
appropriate corrective action.
UnStb (Unstable)
Motion is present when trying to perform a print function.
CORRECTIVE ACTION: Wait for a stable weight display (STABLE annunciator on) before
performing any of this operation.
CALIBRATION SEAL INSTALLATION
If your Model 210/215 Weight Indicator is used in a commercial application it must be tested
and sealed by your local weights and measurements official. The 210/215 is designed to
accept a lead and wire security seal to prevent unauthorized access to the calibration
adjustments. Refer to Figure No. 12 for details on the installation of the seal.
Figure No. 12
8200-M411-O1 Rev D  210/215 Installation & Technical
43
AXLE WEIGHER MODE OPERATION
After placing the wheel load weighers on the ground in front of the vehicle(s) to be weighed,
the two weighers are connected together using the interconnection cable assembly. One
weigher (makes no difference which) is connected to the indicator using the indicator interface
cable. The interconnection diagram is shown below:
Printer
Weight
Indicator
Indicator Cable
Interface Cable
Wheel Load
Weigher
Wheel Load
Weigher
12 VDC Power
1. With power applied to the indicator, press the ON key to turn on the indicator.
2. Verify that the weight display is at zero ( 00 ). If not, press the ZERO key.
3. Have the vehicle driven forward until the first axle is on the center of the wheel load
weighers.
4. Observe the weight of the first axle and press the PRINT key to record the weight,
date and time.
5. Have the vehicle pull forward until the next axle is on the center of the wheel load
weighers. NOTE! If the next axle is a tandem or tridem set of axles, place ONLY
the first axle of the group on the wheel load weighers.
6. Observe the weight of this axle and press the PRINT key to record the weight, date
and time.
7. Repeat step 5 until all of the remaining axles have been weighed and printed.
8. After the last axle has been weighed and its value recorded, pull the vehicle off the
wheel load weighers.
9. Press the  (asterisk) key and then press the PRINT key. The total of all of the
vehicle axle weights will be recorded and printed. The example below illustrates a
typical print ticket for a five-axle truck.
Time
13:47
1
2
3
4
5
Total
09-26-09
15440 lb
16320 lb
15980 lb
15880 lb
15700 lb
79320 lb
Date
Axle Weights
Total Vehicle
Weight
Axle Numbers
44
8200-M411-O1 Rev D  210/215 Installation & Technical
AXLE WEIGHER MODE OPERATION, CONT.
Additional Features
If you wish to also record the total of any axle groups, press the number key corresponding to
the number of axles in the axle group to be totaled when the first axle in the group is weighed.
After the last axle in the group is recorded, the printer will automatically record the subtotal of
the axle group weights. In the previous example, assume that axles 2 and 3 form a tandem
pair of axles as do axles 4 and 5. To record the total weight of these axle groups, press the
number 2 key followed by the PRINT key when printing axles 2 and 4. This indicates that the
next two axles form an axle group whose total is to be recorded. The example below
illustrates the print format when the two axle groups are identified.
13:47
1
2
3
2,3
4
5
4,5
Total
09-26-09
15440 lb
16320 lb
15980 lb
32300 lb
15880 lb
15700 lb
31580 lb
79320 lb
Axle Group
Totals
Note that there is a maximum of 9 single axles in an axle group and that the axles must be
weighed in a consecutive group. The axles comprising the axle group are also identified on
the printed record.
If you wish to print additional copies of the printed record for the vehicle, press the  (asterisk)
key again followed by the PRINT key and a summary print will be produced. This can be
repeated as often as necessary to secure the number of desired copies. Note, however, that
as soon as the first axle of the next vehicle is printed, the weights from the previously weighed
vehicle are cleared.
8200-M411-O1 Rev D  210/215 Installation & Technical
45
PART IDENTIFICATION
(210 Rear Enclosure Sub Assembly)
ITEM NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
46
QTY.
8
4
2
1
4
1
4
5
1
10
4
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
PART NUMBER
6013-0039
6013-0245
6021-0654
6021-1108
6024-0108
6024-1081
6540-1104
6610-2248
6610-5007
6680-0004
6680-0138
6680-0200
6680-0203
6800-1032
6980-0014
6980-1030
8200-B019-08
8200-B104-08
8200-B204-0A
8200-B205-0A
8200-B212-0A
8200-B215-0A
8200-C012-08
8200-C016-0A
8200-C018-08
8510-C346-0I
8512-B350-0A
8200-B206-0A
8526-B232-08
8539-B254-0A
DESCRIPTION
HEX NUT #6-32
HEX NUT #4-40
SCW PAN HEAD #6-32 x .250 PDMS
SCW FILLISTER MACHINE-SCW #10-32 x .375 S.S.
WASHER LOCK INT. TOOTH #4 S.S.
WASHER FLAT #10 NEOPRENE BACKING S.S.
PLUG, HOLE 0.173-.240 RED POLYETH
GLAND CONNECTOR
CABLE CLIP
WASHER LOCK INT. TOOTH #6 Z/P
SPACER #6 x .187 NYLON
POP RIVET
SPACER (PCB) #6-32 x .500
POWER SUPPLY BOARD
WIRE TIE 4” BLACK
POWER CORD 18/3 SVT CEE 6.3 FT
BRACKET: CALIBRATION SWITCH
LABEL: 205/210 TERM. BLOCK
CABLE: 205/210 POWER SUPPLY OUTPUT
CABLE: 205/210 BATTERY CABLE
CABLE: GND
CABLE: AC POWER W/FILTER 205/210 DWI
BRACKET, BATTERY HOLDER
WELDMENT: ENCLOSURE REAR
POWER SUPPLY COVER
LABEL – HIGH VOLTAGE
WIRE: 18GA, GRN, 5.0, #8RT/TINNED
BATTERY POWER BOARD
SPRING, BATTERY COVER
ASSEMBLY: CABLE, CALIBRATION SWITCH
8200-M411-O1 Rev D  210/215 Installation & Technical
PART IDENTIFICATION
(210 Rear Enclosure Sub Assembly)
8200-M411-O1 Rev D  210/215 Installation & Technical
47
PART IDENTIFICATION
(210 Front Enclosure Sub Assembly)
ITEM NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
20
21
48
QTY.
14
1
3
1
10
1
1
3
4
4
1
1
1
1
1
1
1
1
PART NUMBER
6013-0039
6013-0297
6013-0433
6021-0623
6024-1078
6560-0064
6610-5002
6610-5007
6680-0004
6680-1049
6710-1017
8200-B014-08
8200-B020-08
8200-B021-08
8200-C015-0A
8200-C017-0A
8200-C210-OA
8200-D201-1A
8200-D202-08
DESCRIPTION
NUT HEX #6-32
NUT 10-32 HEX
NUT HEX #10-32 ACORN S.S.
SCW PAN HEAD #6-32 x .750 PDMS
WASHER FLAT #6 NEOPRENE BACKING S.S.
DESSICCANT 1 x 1 BAG
GROUND LUG
CABLE CLIP
WASHER LOCK INT. TOOTH #6 Z/P
SPACER (PCB) #6 x ..438
TAPE DBL SIDED 1.0 WIDE 45 MIL THK.
GASKET FOR 210 ENCLOSURE
COVER, BATTERY
GASKET: BATTERY DOOR
WELDMENT: BEZEL FOR 210
WELDMENT: ENCLOSURE, FRONT
DAC PCB (OPTIONAL)
PC BD, ASSY. 210 MAIN
KEYPAD: 210 DWI
8200-M411-O1 Rev D  210/215 Installation & Technical
PART IDENTIFICATION
(210 Final Assembly)
ITEM NO.
1
2
4
5
6
QTY.
1
11
1
1
1
PART NUMBER
593GR986
6013-0433
8200-B026-08
8200-D207-0A
8200-D208-0A
DESCRIPTION
SERIAL TAG ASSEMBLY
NUT HEX #10-32 ACORN S.S.
NUT HEX #10-32 ACORN S.S. DRILLED
SUB ASSEMBLY: REAR ENCLOSURE
SUB ASSEMBLY: FRONT
8200-M411-O1 Rev D  210/215 Installation & Technical
49
PART IDENTIFICATION
(215 Rear Enclosure Sub Assembly)
ITEM NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
50
QTY.
8
3
6
1
8
1
4
4
1
8
4
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
2
8
1
1
1
PART NUMBER
6013-0039
6680-1107
6021-0654
6021-1108
6021-0502
6024-1081
6540-1104
6610-2248
6610-5007
6680-0004
6680-0138
6980-0250
6680-0203
6800-1032
6980-0014
6980-1030
8200-B019-08
8200-B104-08
6610-1506
8200-C420-0A
8200-B212-0A
8200-B237-0A
8200-C404-08
8200-C016-0A
8200-C018-08
8510-C346-0I
8200-C405-08
6680-0052
8200-B410-08
8539-B254-0A
8200-C415-0A
DESCRIPTION
NUT HEX #6-32
SPACER #4-40 x 0.75”
SCW PAN HEAD #6-32 x .250 PDMS
SCW FILLISTER MACHINE-SCW #10-32 x .375 S.S.
SCW PAN HEAD #4-40 x .187 PDMS
WASHER FLAT #10 NEOPRENE BACKING S.S.
PLUG, HOLE 0.173-.240 RED POLYETH.
CONN GLAND .187-.312 GRIP .599 MTG BLK
CABLE CLIP
WASHER LOCK INT. TOOTH #6 Z/P
SPACER #6 x .187 NYLON
EU POWER CORD H05VV-F3G 1mm, 10A/250V, BLACK
SPACER (PCB) #6-32 x .500
POWER SUPPLY BOARD
WIRE TIE 4” BLACK
US POWER CORD 18/3 SVT CEE 6.3 FT
BRACKET: CALIBRATION SWITCH
LABE: 205/210 TERM. BLOCK
GLAND CONN. NICKEL
CONNECTOR BD./BRKT. ASSY.
CABLE: GND
CABLE: AC POWER W/FILTER 205/210 DWI
BATTERY BRACKET
WELDMENT: ENCLOSURE, REAR
POWER SUPPLY COVER
LABEL – HIGH VOLTAGE
BATTERY GUIDE
WASHER, LOCK HELICAL #4
CONNECTOR BOARD MT.
ASSEMBLY: CABLE, CALIBRATION SWITCH
BATTERY TRAY ASSEMBLY
8200-M411-O1 Rev D  210/215 Installation & Technical
PART IDENTIFICATION
(215 Rear Enclosure Sub Assembly)
8200-M411-O1 Rev D  210/215 Installation & Technical
51
PART IDENTIFICATION
(215 Front Enclosure Sub Assembly)
ITEM NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
52
QTY.
16
1
3
1
10
1
3
6
4
1
1
1
1
1
1
1
2
1
PART NUMBER
6013-0039
6013-0297
6013-0433
6024-0037
6024-1078
6610-5002
6610-5007
6680-0004
6680-0204
8200-B014-08
8200-B020-08
8200-B021-08
8200-C015-0A
8200-C408-0A
8200-C210-0A
8200-D402-08
6024-1022
8200-D401-0A
DESCRIPTION
NUT, HEX #6-32
NUT, HEX #10-32
NUT, HEX #10-32 ACORN S.S.
WASHER, LOCK #10 HELICAL SPLIT
WASHER, FLAT #6 NEOPRENE BASCKING S.S.
GROUND LUG
CABLE CLIP
WASHER, LOCK INT. TOOTH #6 Z/P
SPACER (PCB) #6 x 0.531
GASKET FOR 210 ENCLOSURE
COVER, BATTERY
GASKET: BATTERY DOOR
WELDMENT: BEZEL FOR 210
WELDMENT: ENCLOSURE, FRONT
DAC PCB (OPTIONAL)
KEYPAD: 215 DWI
#6 FLAT WASHER
PC BD. ASSY. 215 MAIN
8200-M411-O1 Rev D  210/215 Installation & Technical
PART IDENTIFICATION
(215 Final Assembly)
ITEM NO.
1
2
3
4
5
6
7
8
QTY.
1
11
1
1
1
1
1
1
PART NUMBER
593GR986
6013-0433
6650-0087
8200-B026-08
8200-D412-0A
8200-D413-0A
8200-D412-1A
8200-D413-1A
DESCRIPTION
SERIAL TAG ASSY.
NUT HEX #10 ACORN S.S.
LABEL: MADE IN USA
NUT HEX #10 ACORN S.S. DRILLED
SUB ASSEMBLY: REAR ENCLOSURE
SUB ASSEMBLY: FRONT 215
SUB ASSEMBLY: REAR ENCLOSURE EU MODEL
SUB ASSEMBLY: FRONT 215-A (with DAC Option)
8200-M411-O1 Rev D  210/215 Installation & Technical
53
54
8200-M411-O1 Rev D  210/215 Installation & Technical
APPENDIX A:
MODEL 210DC AND 215DC
The Models 210DC and 215DC have been created to change the input power requirement
from 115-230VAC, 0.4A to 12-15VDC, 1.0A. The AC input filtering and AC–DC converter
components have been removed from the back panel of the indicator.
The input power wiring and the main printed circuit board power wiring have been changed.
The input power source can be provided by the user and is to be 12-15VDC, 1A. The main
printed circuit board positive (red) power wire is connected to the L1(H) terminal and the
negative (black) wire is connected to the GND terminal of the input power terminal block.
Strip ¼” of insulation from each of the power source positive and negative wires. Solder tin
each wire. Connect the positive (+) voltage source wire to the terminal marked L1(H) on the
terminal block as shown below. Connect the negative (-) voltage source wire to the terminal
marked GND on the terminal block as shown below.
The indicators can be operated as described in this manual.
IMPORTANT! The indicators are shipped with the load cell excitation voltage set to
12V (J3 open) for a 14-15 VDC source. To operate from a 12-14 VDC source, the
load cell excitation voltage MUST be set to 8V (J3 closed). Operation with the load
cell excitation voltage set to 12V will result in an unstable weight display. Refer to
Figure No. 8 for the location of J3.
R
E
D
B
L
K
Positive Wire
Negative Wire
8200-M411-O1 Rev D  210/215 Installation & Technical
55
STATEMENT OF LIMITED WARRANTY
WARRANTY TERMS
Cardinal Scale Manufacturing Company warrants the equipment we manufacture against defects in material and
workmanship. The length and terms and conditions of these warranties vary with the type of product and are
summarized below:
PRODUCT
TYPE
VEHICLE SCALE
WEIGHT
INDICATORS
VEHICLE SCALE
LOAD CELLS
Ex. Hydraulic
HYDRAULIC
LOAD CELLS
1
TERM
MATERIAL
LIGHTNING
WATER
AND
DAMAGE
DAMAGE
WORKMANSHIP See note 9 See note 7
1
YEAR
5
YEARS
LIFE
CORROSION ON-SITE
See note 4
LABOR
YES
YES
YES
YES
NO
YES
YES
YES
YES
90 DAYS
YES
YES
YES
YES
90 DAYS
8200-M411-O1 Rev D  210/215 Installation & Technical
LIMITATIONS
AND
REQUIREMENTS
1,2,3,5,6
A,B,C,D
1,2,3,5,6
A,B,C,D
1,5,6,8
A,B,C,D
PRODUCT
TYPE
VEHICLE
SCALE
STRUCTURE
ALL OTHER
CARDINAL
PRODUCTS
TERM
5
YEARS
1
YEAR
90
PARTS
DAYS
VEHICLE
SCALES
LIGHTNING
WATER
AND
DAMAGE
DAMAGE
WORKMANSHIP See note 9 See note 7
REPLACEMENT
IN-MOTION
MATERIAL
1
YEAR
CORROSION ON-SITE
See note 4
LABOR
YES
YES
YES
YES
90 DAYS
YES
NO
YES
YES
NO
YES
NO
YES
YES
NO
YES
NO
YES
YES
90 DAYS
Ph. (800) 441-4237
E-mail: [email protected]
203 E. Daugherty
Webb City, MO 64870
8200-M411-O1 Rev D  210/215 Installation & Technical
LIMITATIONS
AND
REQUIREMENTS
1,2,3,5,6
A,B,C,D
1,2,5,6
A,B,C,D
1,2,4,5,6
A,B,C,D
1,2,5,6
A,B,C,D
02/11
Printed in USA
315-WARRANTY-CAR-G
2
APPLICABLE LIMITATIONS AND REQUIREMENTS
1. This warranty applies only to the original purchaser. The warranty does not apply to equipment that has been
tampered with, defaced, damaged, or had repairs or modifications not authorized by Cardinal or has had the
serial number altered, defaced or removed.
2. This warranty is not applicable to equipment that has not been grounded in accordance with Cardinal’s
recommendations.
3. This equipment must be installed and continuously maintained by an authorized Cardinal dealer.
4. Applies only to components constructed from stainless steel.
5. This warranty does not apply to equipment damaged in transit. Claims for such damage must be made with the
responsible freight carrier in accordance with freight carrier regulations.
6. Warranty term begins with date of shipment from Cardinal.
7. Only if device is constructed for outdoor use.
8. Lifetime warranty applies to damages resulting from water, lightning, and voltage transients and applies only to
the hydraulic load cell structure itself (does not include pressure transducers, rubber seals, o-rings, and
associated wiring).
9. Except for hydraulic load cells, warranty coverage for damage resulting from lightning is valid ONLY when the
device is installed in strict accordance with Cardinal’s installation instructions including the use of recommended
grounding and surge suppression circuitry.
3
8200-M411-O1 Rev D  210/215 Installation & Technical
EXCLUSIONS
A.)
This warranty does not include replacement of consumable of expendable parts. The warranty does not
apply to any item that has been damaged due to unusual wear, abuse, improper line voltage,
overloading, theft, fire, lightning, water, prolonged storage or exposure while in purchaser’s possession or
acts of God unless otherwise stated herein.
B.)
This warranty does not apply to peripheral equipment not manufactured by Cardinal. This equipment will
normally be covered by the equipment manufacturer’s warranty.
C.)
This warranty sets forth the extent of our liability for breach of any warranty or deficiency in connection
with the sale or use of our product. Cardinal will not be liable for consequential damages of any nature,
including but not limited to loss of profit, delays or expenses, whether based on tort or contract. Cardinal
reserves the right to incorporate improvements in material and design without notice and is not obligated
to incorporate said improvements in equipment previously manufactured.
D.)
This warranty is in lieu of all other warranties expressed or implied including any warranty that extends
beyond the description of the product including any warranty of merchantability or fitness for a particular
purpose. This warranty covers only those Cardinal products installed in the forty-eight contiguous United
States and Canada.
Ph. (800) 441-4237
E-mail: [email protected]
203 E. Daugherty
Webb City, MO 64870
8200-M411-O1 Rev D  210/215 Installation & Technical
02/11
Printed in USA
315-WARRANTY-CAR-G
4
Addendum to the
200, 205, 210 and 215
Installation and Technical Manual
TEST MODE
This addendum is to inform you of the TEST MODE feature in the 200, 205, 210 and 215 Weight Indicators.
This addendum should be used in addition to the Installation and Technical manual for your indicator.
NOTE! On the 200 and 205, the functions of numeric keys are replaced by using UNITS/LEFT ARROW
and ASTERISK/UP ARROW keys. The cursor location is identified by the blinking character and can be
advanced to the left to the next position by pressing the UNITS/LEFT ARROW key. Pressing the
ASTERISK/UP ARROW key will change the blinking character to the next value.
To Start Test Mode
1.
2.
3.
4.
5.
6.
7.
8.
Remove calibration access screw.
Press ON/OFF key to turn indicator ON.
Insert a small screwdriver or other tool into the access hole and press the CAL switch.
Display will change to SETUP.
Press UNITS/TEST key.
Display will change to tESt=.
Press ENTER key to show current test function value (which will be 0, test feature off).
Using the numeric keys, enter test function value and then press ENTER key.
4 = raw A/D readings
16 = display milliVolts
9. Display will change to SETUP.
10. Press ¾ (ASTERISK) key to begin test.
11. Display will change to show test data.
To Change Test Mode
1. With indicator displaying test data, insert a small screwdriver or other tool into the access hole and
press the CAL switch.
2. Display will change to SETUP.
3. Press UNITS/TEST key.
4. Display will change to tESt=.
5. Press ENTER key to show current test function value.
6. Using the numeric keys, enter test function value and then press ENTER key.
4 = raw A/D readings
16 = display milliVolts
7. Display will change to SETUP.
8. Press ¾ (ASTERISK) key to begin test.
9. Display will change to show test data.
To Stop Test Mode
1. With indicator displaying test data, insert a small screwdriver or other tool into the access hole and
press the CAL switch.
2. Display will change to SETUP.
3. Press UNITS/TEST key.
4. Display will change to tESt=.
5. Press ENTER key to show current test function value.
6. Press numeric 0 key (0 = test feature off) and then press ENTER key.
7. Display will change to SETUP.
8. Press ¾ (ASTERISK) key to stop test and reset indicator.
9. The indicator is now ready for normal operation.
IMPORTANT! Once TEST MODE has been enabled, the indicator will power on with TEST on
the display. Operator must press ENTER key to stay in test mode or press ¾ (ASTERISK) key
to disable test mode.
ADDENDUM FOR MANUALS:
8200-M035-O1 Rev B 10/09, 8200-M024-O1 Rev G 10/09, 8200-M411-O1 Rev C 10/09
01/10
Addendum to the
200, 205, 210 and 215
Installation and Technical Manual
This addendum is to inform you of changes to the 200, 205, 210 and 215 Weight Indicators.
This addendum should be used in addition to the Installation and Technical Manual for your
indicator. Refer to the manual for information concerning the installation, setup, and operation
of your 200, 205, 210 or 215 Weight Indicator.
REMOTE INDICATOR SETUP
Beginning with version 2.6.1 of the firmware, an additional prompt has been added to the A-d
section of the setup.
If the indicator is to function as a remote indicator, press the YES key at the SErSCL
prompt. If not then press the NO key at the prompt.
If SErSCL was set to YES then, an additional prompt has also been added in the SIO
section for selecting the port for the LOCAL/REMOTE communications.
At the LrP prompt enter either 1 for port 1 or 3 if the optional 2xx-RS232 card is
being used.
IMPORTANT!
If a 200, 205, 210 or 215 indicator is to be used as the LOCAL and as the REMOTE, then both
indicators MUST have Rev 2.6.1 or greater software installed.
If a combination of 200, 205, 210 or 215 and a 225 indicator are to be used in a
LOCAL/REMOTE configuration, then the 200, 205, 210 or 215 indicator MUST have Rev 2.6.1
or greater software installed, and the 225 indicator MUST have Rev 1.0.K or greater software
installed.
 This operation is not support with a 220 indicator. 
ADDENDUM FOR MANUALS:
8200-M035-O1 Rev B, 8200-M024-O1 Rev G and H, 8200-M411-O1 Rev C and D
02/11
Technical Support:
Ph:210
866-254-8261
200, 205,
and 215 Rev [email protected]
2.6.1 Addendum
1
CONTINUOUS DATA OUTPUT FORMATS
TOLEDO
Beginning with version 2.6.1 of the firmware, the Toledo output has been expanded to provide
a selection between the short or long format and also whether or not to include the optional
checksum.
If type 7 is chosen at the tSHort prompt, press the YES key to select the SHORT
format or press the NO key to select the LONG format.
If the optional checksum is to be included press the YES key at the CSU prompt,
otherwise press the NO key for no checksum.
Short Format:
<stx><swa><swb><swc>xxxxxx<cr><sum>
Long Format:
<stx><swa><swb><swc>xxxxxxyyyyyy<cr><sum>
Where
<stx>
<swa>
<swb>
<swc>
xxxxxx
yyyyyy
<cr>
<sum>
2
is an ASCII Start-of-Text character
is status character a
is status character b
is status character c
is the displayed weight
is the tare weight
is an ASCII carriage return
is the optional checksum
200, 205, 210 and 215 Rev 2.6.1 Addendum
CONTINUOUS DATA OUTPUT FORMATS, CONT.
RANGER 5000 FORMAT A
Beginning with version 2.6.1 of the firmware, the Ranger 5000 Format A has been added to
the Continuous Data Output Formats. In setup, select type 9 for the Ranger 5000 format.
At the StArtb prompt, enter the decimal value for the start character.
Valid entry is 0 to 126.
At the Endb 1 prompt, enter the decimal value for the first end character.
Valid entry is 0 to 126.
At the Endb 2 prompt, enter the decimal value for the second end character.
Valid entry is 0 to 126.
If the above items are ‘0’ then the character will not be included in the data stream.
Format
<StArtb>Sign WeightA(7) Status
Where,
Sign
is the sign of the weight (‘ ‘ for positive, ‘-‘ for negative)
WeightA is a seven character string containing the current weight including the
decimal point. If there is no decimal point, then the first character is a
space. Leading zero blanking applies.
Status
provides information on the weight reading. The characters G/N/U/O/M/E
represent Gross/Net/Underload/Overload/Motion/Error respectively.
200, 205, 210 and 215 Rev 2.6.1 Addendum
3
CONTINUOUS DATA OUTPUT FORMATS, CONT.
GEDGE 1650 FORMAT 4
Beginning with version 2.6.1 of the firmware, the GEDGE 1650 Format 4 has been added to
the Continuous Data Output Formats. In setup, select type 10 for the GEDGE format.
At the TdAte prompt, enter the format for the date and time (0-4).
At the StrtC prompt, enter the decimal value for the start character (0-126)
At the EbLoC prompt, enter the decimal value for the end block character or data
separator (0-126).
At the dbUb prompt, enter the decimal value for the device number (0-99).
Format
<Bg><DT><BD><No><BD><W1><BD><D2><D3><D4><D5><D6><D7><BD><En>
Where,
Bg
DT
BD
D2
D3
D4
D5
D6
D7
En
No
W1
4
is the starting character, if 0 then it is not transmitted.
is the Date and Time the following BD character is output only if the
date/time is output.
Block division character.
Displayed weight identity. G=gross, N=net
M scale is in motion, S scale is stable.
Inscale (0>=weight<=capacity) Overcap U=below zero
Z=Center-of-Zero, otherwise ASCII space
E=Tare not equal to 0, otherwise ASCII space
Always an ASCII space
End of transmission character
Device Number 01 thru 99. If set to 0 above, then nothing is output.
Displayed weight.
200, 205, 210 and 215 Rev 2.6.1 Addendum
Addendum to the
200, 205, 210 and 215
Installation and Technical Manual
This addendum is to inform you of changes to the 200, 205, 210 and 215 Weight Indicators.
This addendum should be used in addition to the Installation and Technical Manual for your
indicator. Refer to the manual for information concerning the installation, setup, and operation
of your 200, 205, 210 or 215 Weight Indicator.
LINEARIZATION FOR GUARDIAN SCALE
Beginning with version 2.6.4 of the firmware, an additional prompt has been added after the
CAL? section of the setup.
If a GUARDIAN scale is connected to the indicator, at the SST? prompt press the
YES key.
The tLo= prompt will be displayed. This is the low end of the range of weight that
requires adjusting. For example, if after performing linearization testing, the
displayed weight is 5 lbs low between 10,000 lbs and 15,000 lbs, the value for the
tweak low weight is 10000.
Input the tweak low weight value and then press the ENTER key.
The tHi= prompt will be displayed. This is the high end of the range of weight that
requires adjusting. Using the example above, the value for the tweak high weight is
15000.
Input the tweak high weight value and then press the ENTER key.
The tUAL= prompt will be displayed. This is the amount of weight that needs to be
added (or subtracted) from the range of weight to bring the displayed weight into
tolerance. Again, using the example above, the Tweak Weight value would be 5.
Input the tweak weight value (pressing the NET key will change the sign) and then
press the ENTER key.
When the indicator is turned on, it will display SST for a couple of seconds if the SST? prompt
was answered YES in setup.
ADDENDUM FOR MANUALS:
8200-M035-O1 Rev B, 8200-M024-O1 Rev G and H, 8200-M411-O1 Rev C and D
02/11
Technical Support: Ph: 866-254-8261  [email protected]
1
8200-M411-O1 Rev D  210/215 Installation & Technical
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement