Detecto Mariner WPS12 Owner's manual

Detecto Mariner WPS12 Owner's manual
MARINER
MODEL WPS12
WATERPROOF DIGITAL
PORTION SCALE
OWNER’S MANUAL
8528-0409-0M Rev A
04/15
CARDINAL SCALE MFG. CO.
203 E. Daugherty, Webb City, MO 64870 USA
PH (417) 673-4631  FAX (417) 673-5001
www.detectoscale.com
Technical Support: Ph: 866-254-8261  [email protected]
2
INTRODUCTION
TABLE OF CONTENTS
Thank you for purchasing our Detecto Model
WPS12 Waterproof Digital Portion Scale.
Installation …………………..………………..
Unpacking ……………………..…………
Power Supply …………………..………..
Battery Pack …..………………..………..
Battery Charging ...................................
Low Battery ……..…………..……………
Display Annunciators ………..…..………….
Key Functions ………………..…..………….
Operation …..………….…………………..…
Configuration ………….…………………..…
Gravity Compensation ……………….……..
Display Messages ………………..………….
Care and Maintenance …………………..….
This manual will guide you through installation, and
operation of your scale. Please read it thoroughly
before attempting to operate this scale and keep it
handy for future reference.
FCC COMPLIANCE STATEMENT
This equipment generates, uses and can radiate
radio frequency, and if not installed and used in
accordance with the instruction manual, may
cause interference to radio communications. It has
been designed within the limits for a Class A
computing device pursuant to Subpart J of Part 15
of FCC rules to provide reasonable protection
against such interference when operated in a
commercial environment. Operation of this
equipment in a residential area may cause
interference in which case the user will be
responsible to take whatever measures necessary
to correct the interference.
1
1
1
1
1
1
2
3
4
5
6
7
7
SPECIFICATIONS
Weight Display: 5Digits, Height 24.3mm, HTN
You may find the booklet “How to Identify and
Resolve Radio TV Interference Problems”
prepared by the Federal Communications
Commission helpful. It is available from the U.S.
Government Printing Office, Washington, D.C.
20402. Request stock No. 001-000-00315-4.
COPYRIGHT
All rights reserved. Reproduction or use, without
expressed written permission, of editorial or
pictorial content, in any manner, is prohibited. No
patent liability is assumed with respect to the use
of the information contained herein.
Dimensions:
187mm x 246mm x 57mm
Platform Size:
184 mm x 172mm
Zero:
Established on power up routine
and maintained by auto-zero
circuitry.
Power:
AC adapter:
120 VAC input
9v, 100mA output
Battery:
Ni-MH rechargeable
4.8 VDC 1800 mA
DISCLAIMER
While every precaution has been taken in the
preparation of this manual, the Seller assumes no
responsibility for errors or omissions. Neither is
any liability assumed for damages resulting from
use of the information contained herein. All
instructions and diagrams have been checked for
accuracy and ease of application; however,
success and safety in working with tools depend to
a great extent upon the individual accuracy, skill
and caution. For this reason the Seller is not able
to guarantee the result of any procedure contained
herein. Nor can they assume responsibility for any
damage to property or injury to persons
occasioned from the procedures. Persons
engaging the procedures do so entirely at their
own risk.
Tare:
100% of full scale capacity
Temperature
Operation:
Storage:
40 to 105°F (5°to 40°C)
140°F (60°C) Maximum
Capacity:
12lb x 0.1oz, 12lb x 1/8 oz,
12lb x 0.005 lb, 192 oz x 0.05 oz,
192 oz x 1/8 oz, 5500g x 1 g
Keys:
ON/OFF, TARE, UNITS/Back
Light, SET
Features:
IP67
PRECAUTIONS
Serial Number_______________________
Before using this instrument, read this
manual and pay special attention to all
"NOTIFICATION" symbols:
Date of Purchase ____________________
Purchased Form_____________________
___________________________________
___________________________________
IMPORTANT
RETAIN THIS INFORMATION FOR FUTURE USE
1
ELECTRICAL
WARNING
2
INSTALLATION
UNPACKING
Before beginning installation of your scale, make certain the instrument has been received in
good condition. When removing the scale from its packing, inspect it for signs of damage, such
as exterior dents and scratches. Keep the carton and packing material for return shipment if it
should become necessary. It is the responsibility of the purchaser to file all claims for any
damages or loss incurred during transit.
1. Remove the scale from the shipping carton and inspect it for any signs of damage.
2. Plug-in the adapter to use the scale and begin charging the battery pack. Refer to the
POWER SUPPLY or BATTERY PACK sections of this manual for more instruction.
3. Place the scale on a flat level surface, such as a table or bench.
4. The scale is now ready for use.
POWER SUPPLY
To apply power to the scale using the supplied power supply,
insert the plug from the power supply cable into the power jack on
the side of the scale and then plug power supply into the proper
electrical outlet. The scale is now ready for operation.
BATTERY PACK
The scale uses a 4.8 VDC, 1800 mA built-in rechargeable battery pack. The WPS12 can
operate for up to 80 hours of continuous use with a fully charged battery pack.
BATTERY CHARGING
To recharge the battery pack, the power supply must be connected to an AC power outlet and
plugged into the scale. It will take approximately 5 hours to fully recharge the battery pack in the
scale. While the batteries are charging the WPS12 can still be operated. Note that charging the
battery pack for more than 12 hours will not damage it.
LOW BATTERY
When the battery pack is near the point it needs to be recharged, a low battery indicator on the
display will turn on. If the battery voltage drops too low for accurate weighing, the scale will
automatically shut off and you will be unable to turn it back on. When the low battery indicator is
displayed, the operator should plug the power supply into the scale and then into the proper
electrical wall outlet. The scale will begin charging the battery pack.
1
DISPLAY ANNUNCIATORS
The annunciators are turned on to indicate that the scale display is in the mode corresponding to
the annunciator label or that the status indicated by the label is active.
The O annunciator is turned on when the weight display is stable.
lb
The lb annunciator is turned on to indicate that the displayed weight is in pounds.
oz
The oz annunciator is turned on to indicate that the displayed weight is in ounces.
lb oz
Both the lb and oz annunciators are turned on to indicate that the displayed weight is in pounds
and ounces.
g
The g annunciator is turned on to indicate that the displayed weight is in grams.
The low battery annunciator is used with the battery operation. It will turn on to indicate that the
batteries will soon need to be recharged.
Low limit setting annunciator
High limit setting annunciator
2
KEY FUNCTIONS
UNITS /
1. Press to change the weighing units to the alternate units of measurement (if
selected during configuration of the scale).
2. Press and hold three (3) seconds to turn display back light on or off.-
TARE
1. Press to reset the displayed weight to zero up to 100% of the scale capacity.
ON/OFF
1. Press and release to turn on scale.
2. Press and release to turn the scale off.
3
OPERATION
TURN THE SCALE ON
Press the ON/OFF key to turn the scale on.
The scale will display all display segments then change to zero weight.
SELECT THE WEIGHING UNIT
Press the UNITS key to alternate between the selected weighing units. NOTE: Multiple
weighing units must be enabled during configuration for this function to be operational.
WEIGH
Place the item to be weighed on the scale tray. Scale will display item weight.
TO RE-ZERO THE WEIGHT DISPLAY
To Zero or Tare the weight display, press the TARE key and continue. The scale will
re-ZERO / TARE until the full capacity is reached.
TARE
To weigh ingredients in a container you must first TARE the weight of the container so that
only the net weight of the ingredient is displayed.
1. Place empty container on scale platform while scale is OFF
2. Turn scale on. Display will show zero weight.
3. Add ingredient to container. Scale will display weight of ingredient.
4. To weigh additional ingredients, press TARE before adding each ingredient.
5. To display the total weight of ingredients press the SET and TARE keys at the
same time.
6. Note that upon removing the container and ingredients the scale will display a
negative weight. Press the TARE key to return the scale to zero.
HIGH / LOW WEIGHT CHECKING
The scale may be set to alert you when either over or under a set limit.
1. Press and hold the TARE key for 3 seconds. The scale will beep and display
the low weight annunciator
2. Place weight equal to low weight limit on scale and press SET. Scale will beep
indicating low limit is set. Scale will display the high weight annunciator.
3. Add weight to scale until weight is equal to desired high weight limit. Press
SET. Scale will beep indicating high limit is set. Remove weight from scale.
The scale will now beep and display will indicate if item placed on scale is over or under
the set limits.
To clear the HIGH / LOW settings, press SET and TARE keys at the same time
The membrane keyboard is not to be operated with pointed objects (pencils,
pens, fingernails, etc.). Damage to keyboard resulting from this practice will
NOT be covered under warranty.
4
CONFIGURATION
The Scale has been pre-configured at the factory and should not require configuration for use in
most applications. In the event that the factory settings do not meet the requirements of your
application, the following describes the steps to configure the scale.
TO BEGIN CONFIGURATION:
1. Press the ON/OFF key to turn on the scale.
2. Press and hold the SET key for 3 seconds. When the display shows Set , release the
SET key to enter the Configuration mode. The display will change to show Unit .
WEIGHING UNITS
To select “lb/oz” (pounds/ounce) weighing units (12 lb x 0.1 oz):
1. With the display showing Unit , press the SET key. The display will change to show
“g” and the status ( On or OFF ).
2. Press the UNIT key to toggle between:
Enable (display will change to On ) or
Disable (display will change to OFF ).
3. Press the SET key.
4. Repeat above steps for each weighing unit mode :
• g = grams (5500g x 1 g)
• lb oz = pound ounces (12 lb x 0.1 oz)
• lb oz 1/8 = pound / 1/8 ounces (12 lb x 1/8 oz)
• lb = pounds only (12 lb x 0.005 lb)
• oz = ounces (192 oz x 0.05 oz)
• oz 1/8 = 1/8 ounces (192 oz x 1/8 oz)
5. The display will return to UNIT .
6. Press UNIT key to proceed to AUTOMATIC SHUTOFF
AUTOMATIC SHUTOFF
1.
2.
3.
4.
5.
6.
The display will change to AOFF .
Press the SET key to begin selection of the automatic shut-off time (in seconds).
Press the UNIT key to toggle through the selections, 120, 180, 240, 300, or OFF.
When the desired time or Off is displayed, press the SET key.
The display will return to AOFF .
Press UNIT key to proceed to GRAVITY COMPENSATION.
5
CONFIGURATION, CONT.
GRAVITY COMPENSATION
1. With the display showing GrAu :
To Enable the Gravity Compensation mode, press the SET key. The display will
change to On (use the factory set value of 9.797).
To Disable the Gravity Compensation mode, press the UNIT key. The display will
change to OFF (use the value obtained from the factory Tech Support).
2.
3.
4.
5.
Press the SET key again. The display will change to show GrAu .
Press the UNIT key. The display will change to show End .
Press the SET key to save the settings and reset the scale.
Setup is complete.
GRAVITY COMPENSATION
The Gravity Compensation for your scale has been pre-configured at the factory and should not
require changing in most locations. In the event that the factory settings do not meet the
requirements of your location, contact the factory Tech Support for the value for your location.
With GrAu enabled in the function setting of the Configuration mode, the scale will use the
factory set value of 9.797 for the Gravity Compensation.
If the GrAu is disabled, the scale will use the value obtained from the factory Tech Support
and entered by the operator for the Gravity Compensation.
To change the Gravity Compensation value:
1. Press and hold the UNIT key while pressing the ON/OFF key to turn on the scale and
enter Gravity Compensation mode, the display will show 9.797 (or the current value).
2. Press the UNIT key to increase the value or TARE key to decrease the value to achieve
the desired value.
3. Press the SET key to confirm the entered gravity and return the scale to the normal
operating mode.
CALIBRATION PROCEDURE
1. While the scale is off, press and hold the ON/OFF key.
2. Once all display segments are on, release the ON/OFF key and immediately and press
the UNIT key three (3) times.
3. The scale will show “11111””55555”, and finally show the counts of zero.
4. Press the SET key. The scale will show “0g” and then go back to the counts.
5. Place a 5.5 kg test weight on the scale and then press the SET key.
6. The scale will show “5500g”, and change to show “CAL”, and then automatically turn off.
7. Remove the test weight from the scale.
8. The scale is ready for normal operation.
6
DISPLAY MESSAGES
DISPLAY
MEANING
Lo
Low battery indication
EE
E2 prom Error
OL
Over capacity
CARE AND MAINTENANCE
The heart of the WPS12 Waterproof Digital Portion Scale is a precision load cell located in the
center of the scale base. It will provide accurate operation indefinitely if protected against
overload of scale capacity, dropping items on scale, or other extreme shock.

DO NOT use acetone, thinner or other volatile solvents for cleaning.

DO NOT expose scale to direct sunlight or temperature extremes.

DO NOT place scale in front of heating/cooling vents.

DO clean the scale with a damp soft cloth and mild non-abrasive detergent.

DO clean the scale by submerging in dishpan and using mild non-abrasive detergent.
NOTE: Before submerging scale in dishpan, make sure power jack cover on side of
scale is completely inserted, battery pack cover on bottom of scale is installed and
water temperature does not exceed 140°F (60°C).

DO remove AC power before cleaning with a damp cloth or submerging scale in dishpan.

DO provide clean AC power and adequate protection against lightning damage.

DO keep the surroundings clear to provide clean and adequate air circulation.
DO NOT PLACE SCALE IN COMMERCIAL DISHWASHER TO CLEAN!
7
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement