Leadtek | WinFast GS2030T | User manual | Leadtek WinFast GS2030T User manual

GS2030
User's Manual
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes
no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update
or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note:
For the most up-to-date version of this manual, please see our website at system.leadtek.com.
Leadtek Research, Inc. ("Leadtek") reserves the right to make changes to the product described in this manual
at any time and without notice. This product, including software and documentation, is the property of Leadtek and/
or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except
as expressly permitted by the terms of said license.
IN NO EVENT WILL Leadtek Research, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT
OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, LEADTEK
RESEARCH, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the
State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution
of any such disputes. Leadtek's total liability for all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual,
may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials : This Perchlorate warning applies only
to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate ”.
WARNING: Handling of lead solder materials used in this product may expose you to lead, a
chemical known to the State of California to cause birth defects and other reproductive harm.
The products sold by Leadtek are not intended for and will not be used in life support systems, medical equipment,
nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical
systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic
property damage. Accordingly, Leadtek disclaims any and all liability, and should buyer use or sell such products
for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully
indemnify, defend and hold Leadtek harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
Manual Revision 1.0
Release Date: August 29, 2018
Unless you request and receive written permission from Leadtek Research, Inc., you may not copy any part of this
document. Information in this document is subject to change without notice. Other products and companies referred
to herein are trademarks or registered trademarks of their respective companies or mark holders.
Copyright © 2019 by Leadtek Research, Inc.
All rights reserved.
Printed in the United States of America
WinFast GS2030 User's Manual
Preface
About this Manual
This manual is written for professional system integrators and PC technicians. It provides
information for the installation and use of the WinFast GS2030. Installation and
maintenance should be performed by experienced technicians only.
Please refer to the GS2030 server specifications page on our website for updates on
supported memory, processors and operating systems (http://system.leadtek.com).
Notes
For your system to work properly, please follow the links below to download all necessary
drivers/utilities and the user’s manual for your server.
•
Leadtek product manuals: http://system.leadtek.com
•
Product drivers and utilities: http://system.leadtek.com
If you have any questions, please contact our support team at:
[email protected]
This manual may be periodically updated without notice. Please check the Leadtek website
for possible updates to the manual revision level.
Warnings
Special attention should be given to the following symbols used in this manual.
Warning! Indicates important information given to prevent equipment/property damage
or personal injury.
Warning! Indicates high voltage may be encountered when performing a procedure.
3
Preface
Contents
Chapter 1 Introduction
1.1 Overview................................................................................................................................8
1.2 Unpacking the System..........................................................................................................8
1.3 System Features...................................................................................................................9
1.4 Server Chassis Features.....................................................................................................10
Control Panel.....................................................................................................................10
Front Features....................................................................................................................11
GPU Configuration.............................................................................................................12
Rear Features....................................................................................................................12
1.5 Motherboard Layout............................................................................................................13
Quick Reference Table.......................................................................................................14
Chapter 2 Server Installation
2.1 Overview..............................................................................................................................17
2.2 Preparing for Setup.............................................................................................................17
Choosing a Setup Location................................................................................................17
Rack Precautions...............................................................................................................17
Server Precautions.............................................................................................................18
Rack Mounting Considerations..........................................................................................18
Ambient Operating Temperature.....................................................................................18
Airflow.............................................................................................................................18
Mechanical Loading........................................................................................................18
Circuit Overloading.........................................................................................................19
Reliable Ground..............................................................................................................19
2.3 Installing the Rails...............................................................................................................20
Identifying the Sections of the Rack Rails.........................................................................20
Releasing the Inner Rail....................................................................................................21
Installing the Inner Rails on the Chassis...........................................................................22
Installing the Outer Rails onto the Rack............................................................................23
Sliding the Chassis onto the Rack Rails............................................................................24
Chapter 3 Maintenance and Component Installation
3.1 Removing Power.................................................................................................................25
3.2 Accessing the System.........................................................................................................25
3.3 Motherboard Components...................................................................................................26
4
WinFast GS2030 User's Manual
Processor and Heatsink Installation .................................................................................. 26
The Xeon Scalable Processor ....................................................................................... 27
Heatsinks ....................................................................................................................... 27
Assembling the Processor Package .............................................................................. 28
Removing the Dust Cover from the CPU Socket .......................................................... 31
Installing the Processor Heatsink Module (PHM) ........................................................ 32
Removing the Processor Heatsink Module from the Motherboard ...............................33
Memory Installation ........................................................................................................... 34
Memory Support ............................................................................................................ 34
DIMM Population Requirements .................................................................................... 36
Motherboard Battery ......................................................................................................... 37
3.4 Chassis Components ......................................................................................................... 38
Hard Drives ....................................................................................................................... 38
Graphics Processing Units ................................................................................................ 39
Expansion Card Setup ...................................................................................................... 40
System Cooling ................................................................................................................. 43
System Fan Failure ....................................................................................................... 43
Front and GPU Fans ..................................................................................................... 44
Mid Fans: ....................................................................................................................... 44
Air Shroud ......................................................................................................................... 45
Power Supply .................................................................................................................... 46
Chapter 4 Motherboard Connections
4.1 Power Connections ............................................................................................................ 47
4.2 Headers and Connectors ................................................................................................... 48
Control Panel ................................................................................................................. 50
4.3 Ports ................................................................................................................................... 53
Rear I/O Ports ................................................................................................................ 53
4.4 Jumpers .............................................................................................................................. 55
Explanation of Jumpers ................................................................................................. 55
4.5 LED Indicators .................................................................................................................... 58
Chapter 5 Software
5.1 OS Installation .................................................................................................................... 59
Installing the Windows OS for a RAID System ................................................................ 59
Installing Windows to a Non-RAID System ...................................................................... 59
5
Preface
Chapter 6 BIOS
6.1 Introduction ......................................................................................................................... 63
Starting the Setup Utility ................................................................................................... 63
6.2 Main Setup ......................................................................................................................... 64
6.3 Advanced Setup Configurations ......................................................................................... 66
6.4 Event Logs ......................................................................................................................... 91
6.5 IPMI .................................................................................................................................... 93
6.6 Security Settings ................................................................................................................ 96
6.7 Boot Settings ...................................................................................................................... 99
6.8 Save & Exit....................................................................................................................... 101
Appendix A BIOS Error Codes
Appendix B Standardized Warning Statements for AC Systems
Appendix C System Specifications
6
WinFast GS2030 User's Manual
Chapter 1
Introduction
1.1 Overview
This chapter provides a brief outline of the functions and features of the WinFast
GS2030. The GS2030 is a high-end graphics processing unit (GPU) system comprised
of the X11DPG-SN motherboard and the SC218GHTS-R2K03BP3 chassis.
In addition to the motherboard and chassis, several important parts that are included with
the system are listed below.
Main Parts List
Description
Part Number
Quantity
Air Shroud
MCP-310-21808-0B
2
Heatsinks
SNK-P0068PS, SNK-P0068PSC
1 each
Fans (8-cm)
FAN-0136L4
5
Hot-swap Carriers (for 2.5" HDDs)
MCP-220-00047-0B
10
HDD Backplane
BPN-SAS-218GH-N2
1
Rackmount Rail Kit
MCP-290-00057-0N
1 set
Riser Card Support
Riser Card
Supports
RSC-G2B-A66-X1
Active GPU riser with two PCI-E x16 slots
RSC-G2F-A66-X1
Active GPU riser with two PCI-E x16 slots
RSC-G2FR-A66
Active GPU riser with two PCI-E x16 slots
RSC-R2UG-E16R-X9
Passive GPU riser with one PCI-E x8 slot (in a PCI-E x16 slot)
1.2 Unpacking the System
Inspect the box the WinFast GS2030 was shipped in and note if it was damaged in any
way. If any equipment appears damaged, please file a damage claim with the carrier
who delivered it.
Decide on a suitable location for the rack unit that will hold the server. It should be situated
in a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical noise and
electromagnetic fields are generated. It will also require a grounded AC power outlet nearby.
Be sure to read the precautions and considerations noted in Appendix B.
8
Chapter 1: Introduction
1.3 System Features
The following table provides you with an overview of the main features of the 2029GP-TR.
Please refer to Appendix C for additional specifications.
System Features
Motherboard
X11DPG-SN
Chassis
SC218GHTS-R2K03BP3
CPU
Dual Intel Xeon 81xx/61xx/51xx/41xx/31xx Series processors
Socket Type
Socket P
Memory
Up to 2TB of DDR4-2666/2400/2133 3DS Load Reduced DIMM (3DS LRDIMM), Load Reduced DIMM
(LRDIMM), Registered DIMM (RDIMM), or Non-Vollatile DIMM (NVDIMM) in 16 DIMM slots
Chipset
Intel PCH C621
Expansion Slots
Up to seven PCI-E 3.0 slots (see table on page 12 for details)
Hard Drives
Ten 2.5" hot-swap hard drives
Power
2000W redundant power supply modules (PWS-2K03P-1R)
Form Factor
2U rackmount
Dimensions
(WxHxD) 17.2 x 3.5 x 31 in. (437 x 89 x 787 mm)
9
WinFast GS2030 User's Manual
1.4 Server Chassis Features
Control Panel
The switches and LEDs located on the control panel are described below. See Chapter 4 for
details on the control panel connections.
1
2
3
6
4
7
5
8
Figure 1-1. Control Panel View
Control Panel Features
Item
Feature
Description
1
Power Button
The main power button is used to apply or remove power from the
power supply to the server. Turning off system power with this button
removes the main power but maintains standby power. To perform
many maintenance tasks, you must also unplug system before
servicing
2
Reset Button
The reset button is used to reboot the system.
3
Power LED
Indicates power is being supplied to the system power supply units.
This LED should normally be illuminated when the system is operating.
4
NIC2 LED
Indicates network activity on the LAN2 port when flashing
5
Power Fail LED
Indicates a power supply module has failed when illuminated.
6
HDD LED
Indicates activity on the hard drive when flashing
7
NIC1 LED
Indicates network activity on the LAN1 port when flashing
8
Information LED
See table on the following page.
10
Chapter 1: Introduction
Information LED
Status
Description
Continuously on and
red
An overheat condition has occurred.
(This may be caused by cable congestion.)
Blinking red (1Hz)
Fan failure, check for an inoperative fan.
Solid blue
Local UID has been activated. Use this function
to locate the server in a rackmount environment.
Blinking blue
Remote UID is on. Use this function to identify
the server from a remote location.
Front Features
The SC218GHTS-R2K03BP3 is a 2U rackmount chassis See the illustration below for the
features included on the front of the chassis.
1
2
Figure 1-2. Chassis Front View
Front Chassis Features
Item
Feature
Description
1
Control Panel
See previous page for details.
2
Hard Drive Bays
Ten 2.5" hot-swap hard drive carriers. NVMe drives are only supported
on the last two hybrid HDD bays on the right, which can support SATA/
SAS/NVMe drives.
11
WinFast GS2030 User's Manual
Rear Features
The illustration below shows the features included on the rear of the chassis. The PCI
expansion slots are used for different purposes on each server model as noted below.
3
5
4
6
7
1
1
2
Figure 1-3. Chassis Rear View
Rear Chassis Features
Item
Feature
Description
1
Power Supply Module
Redundant 2000W power supply (PWS-2K03P-1R)
2
I/O Ports
See Section 4.3 for details.
3
Low-profile Slot
Unavailable: reserved slot space for double-wide GPU
4
Low-profile Slot
RSC-R2UG-E16R-X9 riser card (low-profile)
5
FHFL1 Slot
RSC-G2B-A66-X1 riser card (full-height, full-length, CPU2 required)
6
FHFL1 Slot
Unavailable: reserved slot space for double-wide GPU
7
FHFL1 Slot
RSC-G2FR-A66-X1 riser card (full-height, full-length)
GPU Configuration
The GS2030 offers four PCI-E 3.0 x16 slots in the front that can support four passive
double-width GPUs. In addition, there are two PCI-E 3.0 x16 slots that can support two
passive double-width GPUs and one low-profile PCI-E 3.0 x8 slot (in a x16 slot) in the rear.
P40/P100/V100/coprocessor GPUs are supported.
12
WinFast GS2030 User's Manual
Quick Reference Table
Jumper
Description
Default Setting
JBT1
CMOS Clear
Open (Normal)
JPG1
VGA Enable/Disable
Pins 1-2 (Enabled)
JPME1
ME Recovery Mode
Pins 1-2 (Normal)
JPME2
ME Manufacturing Mode
Pins 1-2 (Normal)
JWD1
Watch Dog
Pins 1-2 (Reset)
LED
Description
Status
LE1
UID LED
Solid Blue: Unit Identified
LE2
Front Panel Power LED
Green: Power On
LEDM1
BMC Heartbeat LED
Blinking Green: BMC Normal
Connector
Description
BIOS
BIOS
BT1
Onboard Battery
FAN 1 ~ FAN 4
System/CPU Fan Headers (FAN1: CPU Fan)
FAN A ~ FAN H
System/CPU Fan Headers
IPMI_LAN
Dedicated IPMI LAN Port
I-SATA0~3 / JS1
Intel PCH SATA 3.0 Ports
I-SATA1~4 / JS2
Intel PCH SATA 3.0 Ports
JCOM1
COM Port
JD1
Speaker Header
JF1
Front Control Panel Header
JF2
Front Panel LAN3 and LAN4 Activity LEDs from SIOM
JIPMB1
System Management Bus Header for IPMI 2.0
JL1
Chassis Intrusion Header
JNVME1, JNVME2
P2_NVMe0, P2_NVMe1; Onboard NVMe 0 and 1 for high speed PCI-E storage devices on CPU2
JPCIE1_1 SXB1A
SMC Proprietary Slot1
JPCIE1_2 SXB1B
PCI-Express 3.0 x16 Slot from CPU1
JPCIE1_3 SXB1C
SMC Proprietary Slot1
JPCIE2
PCI-Express 3.0 x16 Slot from CPU2
JPCIE3
PCI-Express 3.0 x16 Slot from CPU1
JPCIE4
PCI-Express 3.0 x16 Slot from CPU2
JPCIE 5
PCI-Express 3.0 x8 Slot from CPU2
JPW1
Proprietary Main Power Connector
JPW2
Power Supply Sideband Connector
JPW3 - JPW7
Backplane Power Connectors for HDDs and GPUs
14
Chapter 1: Introduction
Connector
Description
JRK1
Intel Raid Key Header
JSDCARD1
SD Card Socket
JSIOM
PCI-Express 3.0 x16 slot from CPU1 for Leadtek SIOM add-on Module Support
JSTBY1
Standby Power Connector
JTPM1 TPM/PORT80
Trusted Platform Module/Port 80 Connector
JUIDB1 / UID
Unit Identifier (UID) Switch
JUSB / USB0/1 (3.0)
Back Panel Universal Serial Bus (USB) 3.0 Port
JVGA / VGA
VGA Header
S-SATA0
Intel PCH SATA 3.0 Port
S-SATA1
Intel PCH SATA 3.0 Port
S-SGPIO1
Serial Link General Purpose Input/Output Header 1 for S-SATA ports
15
WinFast GS2030 User's Manual
PCI-E X 16 G3 (Lane Re versal)
PCI-E X 16 G3 (Lane Rever sal)
SLOT 1 PCI-E X 16
(QAT NOT S UPPO RT)
PCI-E #0~3
NC SI
LAN3
RTL8211 F
RJ4 5
BMC Boot Flash
#1
#0
USB 2.0
BM C
SP I
LBG -2 X8 UPLINK NO QAT (14 W
)
NC SI
PCI-E X 1 G2
DDR 4
6.0 Gb/S
AST 250 0
PCI-E #5
#1
#0
#12 USB2.0
USB 2.0
USB 3.0
ESP I
NVME
SLOT 5
SLOT 2
SATA
PCH
LBG-1G
LBG-2
SLOT 4
USB
KR/KX
USB
SFI X 4
#9
#8
#7
#6
#5
#4
#3
#2
#1
#0
1
DM I3
PCI-E X 6
PCI-E X 8 G3 (Lane Re versal)
PCI-E X 16 G3
1
PCI-E X 6
PCI-E X 16 G3
1
SLOT 3
PCI-E X 6
PCI-E X 16 G3
PCI-E X 8 G3 (Lane Re versal)
6
SO CKET I D: 1
#1 #2A #2C #3
DM I2
J2 3
J2 1
J2 0
J1 9
J1 7
J1 5
J14
J1 3
1
PE CI: 31
PCI-E X 6
SNB CORE
DDR- 4
/
266
UPI
P0
8
SO CKET I D: 0
#2
#3 DM I3
P1 VCC P1
6
#1
UPI
DDRIV
2133
P0
SNB CORE
DDR- 4
5+1 PHA SE
145 W
UPI
10.4/11 .2G
PE CI: 30 P1
/
266
DDRIV
2133
SIOM
5+1 PHA SE
145 W
VCC P0
#2- 8
#2- 7
#2- 6
#2- 5
#2- 4
#2- 3
#2- 2
#2- 1
VCC P1 12 v
VR1 3
PCI-E X
VCC P0 12 v
VR1 3
J11 #1- 8
J9 #1- 7
J8 #1- 6
J7 #1- 5
J5 #1- 4
J3 #1- 3
J2 #1- 2
J1 #1- 1
MEMORY V RM : 9294
, ,100 ,10 2
SP I
TP M HEA DER
Debug Car d
VG A HEAD ER
COM1
Hea der
BIO S
SYSTE MPOWE R
FRONT PA NEL
Figure 1-6. Intel PCH C621 Chipset: System Block Diagram
Note: This is a general block diagram and may not exactly represent the features on your
motherboard. See the System Specifications appendix for the actual specifications of your
motherboard.
16
Chapter 2: Server Installation
Chapter 2
Server Installation
2.1 Overview
This chapter provides advice and instructions for mounting your system in a server rack.
If your system is not already fully integrated with processors, system memory etc., refer to
Chapter 4 for details on installing those specific components.
Caution: Electrostatic Discharge (ESD) can damage electronic components. To prevent such
damage to PCBs (printed circuit boards), it is important to use a grounded wrist strap, handle
all PCBs by their edges and keep them in anti-static bags when not in use.
2.2 Preparing for Setup
The box in which the system was shipped should include the rackmount hardware needed to
install it into the rack. Please read this section in its entirety before you begin the installation.
Choosing a Setup Location
•
The system should be situated in a clean, dust-free area that is well ventilated. Avoid areas
where heat, electrical noise and electromagnetic fields are generated.
•
Leave enough clearance in front of the rack so that you can open the front door completely
(~25 inches) and approximately 30 inches of clearance in the back of the rack to allow
sufficient space for airflow and access when servicing.
•
This product should be installed only in a Restricted Access Location (dedicated equipment
rooms, service closets, etc.).
•
This product is not suitable for use with visual display workplace devices according to §2
of the German Ordinance for Work with Visual Display Units.
Rack Precautions
•
Ensure that the leveling jacks on the bottom of the rack are extended to the floor so that
the full weight of the rack rests on them.
17
WinFast GS2030 User's Manual
•
In single rack installations, stabilizers should be attached to the rack. In multiple rack installations, the racks should be coupled together.
•
Always make sure the rack is stable before extending a server or other component from
the rack.
•
You should extend only one server or component at a time - extending two or more simultaneously may cause the rack to become unstable.
Server Precautions
•
Review the electrical and general safety precautions in Appendix B.
•
Determine the placement of each component in the rack before you install the rails.
•
Install the heaviest server components at the bottom of the rack first and then work your
way up.
•
Use a regulating uninterruptible power supply (UPS) to protect the server from power
surges and voltage spikes and to keep your system operating in case of a power failure.
•
Allow any drives and power supply modules to cool before touching them.
•
When not servicing, always keep the front door of the rack and all covers/panels on the
servers closed to maintain proper cooling.
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of
the rack environment may be greater than the room's ambient temperature. Therefore,
consideration should be given to installing the equipment in an environment compatible with
the manufacturer’s maximum rated ambient temperature (TMRA).
Airflow
Equipment should be mounted into a rack so that the amount of airflow required for safe
operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not arise due
to uneven mechanical loading.
18
Chapter 2: Server Installation
Circuit Overloading
Consideration should be given to the connection of the equipment to the power supply circuitry
and the effect that any possible overloading of circuits might have on overcurrent protection
and power supply wiring. Appropriate consideration of equipment nameplate ratings should
be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself should be
grounded. Particular attention should be given to power supply connections other than the
direct connections to the branch circuit (i.e. the use of power strips, etc.).
To prevent bodily injury when mounting or servicing this unit in a rack, you must take
special precautions to ensure that the system remains stable. The following guidelines
are provided to ensure your safety:
•
This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
•
When mounting this unit in a partially filled rack, load the rack from the bottom to the top
with the heaviest component at the bottom of the rack.
•
If the rack is provided with stabilizing devices, install the stabilizers before mounting or
servicing the unit in the rack.
19
WinFast GS2030 User's Manual
2.3 Installing the Rails
This section provides information on installing the chassis into a rack unit with the rails
provided. There are a variety of rack units on the market, which may mean that the assembly
procedure will differ slightly from the instructions provided. You should also refer to the
installation instructions that came with the rack unit you are using.
Note: This rail will fit a rack between 26.5" and 36.4" deep.
Identifying the Sections of the Rack Rails
The chassis package includes two rail assemblies. Each assembly consists of three sections:
An inner rail that secures directly to the chassis, an outer rail that secures to the rack, and
a middle rail which extends from the outer rail. These assemblies are specifically designed
for the left and right side of the chassis.
Rail Assembly
(Shown with Rails
Retracted)
Outer Rail
Middle Rail
Locking Tab
This Side Faces
Inner Rail
Outward
Figure 2-1. Identifying the Rail Sections
20
Chapter 2: Server Installation
Releasing the Inner Rail
Each inner rail has a locking latch. This latch prevents the server from coming completely
out of the rack when when the chassis is pulled out for servicing.
To mount the rail onto the chassis, first release the inner rail from the outer rails.
Releasing Inner Rail from the Outer Rails
1. Pull the inner rail out of the outer rail until it is fully extended as illustrated below.
2. Press the locking tab down to release the inner rail.
3. Pull the inner rail all the way out.
4. Repeat for the other outer rail.
1
2
3
Figure 2-2. Extending the Rails and Releasing the Inner Rail
Note: Both front chassis rails and the rack rails have a locking tab, which serves two functions.
First, it locks the server into place when installed and pushed fully into the rack (its normal
operating position. In addition, these tabs lock the server in place when fully extended from
the rack. This prevents the server from coming completely out of the rack when pulled out
for servicing.
Warning: Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the floor before you slide the unit out for servicing. Failure to
stabilize the rack can cause the rack to tip over.
21
WinFast GS2030 User's Manual
Installing the Inner Rails on the Chassis
Installing the Inner Rails
1. Identify the left and right inner rails. They are labeled.
2. Place the inner rail firmly against the side of the chassis, aligning the hooks on the side
of the chassis with the holes in the inner rail.
3. Slide the inner rail forward toward the front of the chassis until the quick release bracket
snaps into place, securing the rail to the chassis.
4. Optionally, you can further secure the inner rail to the chassis with a screw.
5. Repeat for the other inner rail.
Inner Rails
4
4
2
3
Figure 2-3. Installing the Inner Rails
Slide rail mounted equipment is not to be used as a shelf or a work space.
Warning: do not pick up the server with the front handles. They are designed to pull
the system from a rack only.
22
Chapter 2: Server Installation
Installing the Outer Rails onto the Rack
Installing the Outer Rails
1. Press upward on the locking tab at the rear end of the middle rail.
2. Push the middle rail back into the outer rail.
3. Hang the hooks on the front of the outer rail onto the square holes on the front of the
rack. If desired, use screws to secure the outer rails to the rack.
4. Pull out the rear of the outer rail, adjusting the length until it just fits within the posts of
the rack.
5. Hang the hooks of the rear section of the outer rail onto the square holes on the rear of
the rack. Take care that the proper holes are used so the rails are level. If desired, use
screws to secure the rear of the outer rail to the rear of the rack.
6. Repeat for the other outer rail.
1
L-min=676.00(26.61")(outer rail)
4
21D01
2
3
Figure 2-4. Extending and Mounting the Outer Rails
23
WinFast GS2030 User's Manual
Sliding the Chassis onto the Rack Rails
Warning: Mounting the system into the rack requires at least two people to support the chassis
during installation. Please follow safety recommendations printed on the rails.
Installing the Chassis into a Rack
1. Extend the outer rails as illustrated above.
2. Align the inner rails of the chassis with the outer rails on the rack.
3. Slide the inner rails into the outer rails, keeping the pressure even on both sides. When
the chassis has been pushed completely into the rack, it should click into the locked
position.
4. Optional screws may be used to hold the front of the chassis to the rack.
Ball-Bearing
Shuttle
Figure 2-5. Installing the System into the Rack
Note: Figure is for illustrative purposes only. Always install servers to the bottom of a rack first.
24
Chapter 3: Maintenance and Component Installation
Chapter 3
Maintenance and Component Installation
This chapter provides instructions on installing and replacing main system components. To
prevent compatibility issues, only use components that match the specifications and/or part
numbers given.
Installation or replacement of most components require that power first be removed from the
system. Please follow the procedures given in each section.
3.1 Removing Power
Use the following procedure to ensure that power has been removed from the system. This
step is necessary when removing or installing non hot-swap components or when replacing
a non-redundant power supply.
1. Use the operating system to power down the system.
2. After the system has completely shut-down, disconnect the AC power cord(s) from the
power strip or outlet. (If your system has more than one power supply, remove the AC
power cords from all power supply modules.)
3. Disconnect the power cord(s) from the power supply module(s).
3.2 Accessing the System
The SC218GHTS-R2K03BP3 features a removable top cover, which allows easy access to
the inside of the chassis.
Removing the Top Cover
1. Begin by removing power from the system as described in Section 3.1.
2. Remove the two screws securing the top cover to the chassis.
3. Slide the cover back, toward the rear of the chassis.
4. Lift the cover up and off of the chassis. See Figure 3-1.
Warning: Except for short periods of time, do not operate the server without the cover in place.
The chassis cover must be in place to allow for proper airflow and to prevent overheating.
25
WinFast GS2030 User's Manual
3
5
4
2
3
2
Figure 3-1. Removing the Chassis Cover
3.3 Motherboard Components
Processor and Heatsink Installation
The Intel Xeon 8100/6100/5100/4100/3100 processor series comes in two models: Fabric
(F model) and Non-Fabric (Non-F model). Only the Non-Fabric model is supported for this
system.
The processor (CPU) and heatsink should be assembled together first to form the processor
heatsink module (PHM), and then install the PHM into the CPU socket.
Caution: Use ESD protection. Do not touch the underside of the CPU. Improper installation
or socket misalignment can cause serious damage to the CPU or socket which may require
manufacturer repairs.
Notes:
•
All power should be off, as described in Section 3.1, before installing the processors.
•
When handling the processor package, avoid placing direct pressure on the label area of
the CPU or socket.
•
Check that the plastic socket dust cover is in place and none of the socket pins are bent—
otherwise, contact your retailer.
•
Refer to the Leadtek website for updates on CPU support.
•
Graphics in this manual are for illustration. Your components may look slightly different.
26
Chapter 3: Maintenance and Component Installation
The Xeon Scalable Processor
Non-F model Processor
F model Processor
Figure 3-2. Xeon Scalable Processors
Heatsinks
The 2029GP-TR server uses a slightly different heatsink design for each CPU. The SNKP0068PSC model is used for CPU2, the CPU closer to the mid-chassis fans.
Figure 3-3. Heatsink SNK-P0068PS
27
WinFast GS2030 User's Manual
Assembling the Processor Package
Attach the processor to the thin processor clip to create the processor package.
1. On the top corner of the CPU, locate pin 1 (A), marked by a triangle. Also, locate notch
B and notch C (and notch D for F models) on the CPU as shown below.
2. On the top of the processor clip, l ocate the corner marked by a hollow triangle as
the position for pin 1. Also locate notch B and notch C (and D for F models) on the
processor clip.
3. Align pin 1 of the CPU with its proper position on the processor clip and carefully insert
the CPU into the processor clip. S lide notch B of the CPU into tab B of the processor
clip, and slide notch C of the CPU into tab C of the processor clip (and D for F models)
until the processor clip tabs snap onto the CPU.
4. Examine all corners to ensure that the CPU is properly seated and secure on the
processor clip.
The processor package assembly is created.
C
CPU (Upside Down)
w/CPU LGA Lands up
Align Notch C of the CPU
and Notch C of the Processor Clip
B
A
Pin 1
C
Allow Notch C to
latch on to CPU
Align Notch B of the CPU
and Notch B of the Processor Clip
C
CPU/Heatsink Package
(Upside Down)
B
Align CPU Pin 1
A
B
Allow Notch B to
latch on to CPU
A
Figure 3-4. Processor Package Assembly for the non-F Model Processors
28
Chapter 3: Maintenance and Component Installation
D
CPU (Upside Down)
w/CPU LGA Lands up
Align Notch D of the CPU
and Notch D of the Processor Clip
C
B
Align Notch C of the CPU
and Notch C of the Processor Clip
Align Notch B of the CPU
and Notch B of the Processor Clip
A
Pin 1
D
C
CPU/Heatsink Package
(Upside Down)
B
Align CPU Pin 1
A
Allow Notch D to
latch on to CPU
D
C
B
Allow Notch C to
latch on to CPU
Allow Notch B to
latch on to CPU
A
Figure 3-5. Processor Package Assembly for the F Model Processors
29
WinFast GS2030 User's Manual
After creating the processor package assembly, mount it onto the heatsink to create the
processor heatsink module (PHM).
1. On the heatsink label, locate "1" and the corner next to it. Turn the heatsink upside
down with the thermal grease side facing up, keeping track of the "1" corner.
2. Remove the protective thermal film if present. If this is a new heatsink, the necessary
thermal grease has been pre-applied in the factory. If the heatsink is not new, apply the
proper amount of the thermal grease.
3. In the plastic processor clip, locate the hollow triangle at the corner ("a" in the drawing
below) next to a hole and plastic mounting clips. There is a similar hole and mounting
clips at the diagonal corner of the of the processor clip ("b" in the drawing).
4. With the underside of heatsink and
the underside of the processor
package facing up, align the "1"
corner on the heatsink ("A" in the
drawing) against the mounting clips
next to the hollow triangle ("a") on
the processor package.
5. Also align the corner ("B") at the
diagonal side of the heatsink with
the corresponding clips on the
processor package ("b").
Non-Fabric CPU and Processor Clip
(Upside Down)
Triangle on the CPU
b
c
d
B
a
C
D
Triangle on the
Processor Clip
Heatsink
(Upside Down)
6. Once aligned, press the processor
package assembly onto the heatsink
until the mounting clips (at a, b, c,
and d) snap into place.
A
On Locations of (C, D), the notches
snap onto the heat sink
B
mounting holes
C
D
The processor heatsink module is
assembled.
A
On Locations (A, B), the notches
snap onto the heatsink sides
Figure 3-6. Assembling the Processor Heatsink Module
30
Make sure Mounting
Notches snap into place
Chapter 3: Maintenance and Component Installation
Removing the Dust Cover from the CPU Socket
Remove the dust cover from the CPU socket, exposing the socket pins as shown below.
Caution: Do not touch the socket pins.
Dust Cover
Remove the dust cover from
the CPU socket. Do not
touch the socket pins!
Socket Pins
CPU Socket
Figure 3-7. Removing the Socket Dust Cover
31
WinFast GS2030 User's Manual
Installing the Processor Heatsink Module (PHM)
1. Locate the triangle (pin 1) on the CPU socket. Also locate the pin 1 corner of the PHM
that is closest to "1" on the heatsink label. To confirm, look at the underside of the
PHM and note the hollow triangle in the processor clip and printed triangle on the CPU
located next to a screw at the corner.
2. Align the pin 1 corner of the PHM over the pin 1 corner on the CPU socket.
3. Align the two holes at diagonal corners of the PHM onto the two guide posts on the
socket bracket and carefully lower the PHM onto the socket.
4. Use a T30 Torx-bit screwdriver to install four screws into the mounting holes on the
socket to securely attach the PHM onto the motherboard in the sequence of 1, 2, 3, and
4, as marked on the heatsink label. Gradually tighten each to assure even pressure.
Note: Use only 12 foot-pounds of torque when tightening the screws to avoid damaging
the processor or the socket.
Oval C
Oval D
Use a torque
of 12 lbf
Large Guiding Post
T30 Torx Driver
#4
#2
#1
Small Guiding Post
#3
Printed Triangle
Mounting the Processor Heatsink Module
into the CPU socket (on the motherboard)
Tighten the screws in the
sequence of 1, 2, 3, 4 (top 3 quarter view)
Figure 3-8. Installing the Processor Heatsink Module
32
Chapter 3: Maintenance and Component Installation
Removing the Processor Heatsink Module from the Motherboard
Before removing the processor heatsink module (PHM), power down as described in Section
3.1.
1. Using a T30 Torx-bit screwdriver, loosen and remove the screws on the PHM from the
socket, starting with the screw marked #4, in the sequence of 4, 3, 2, 1.
2. Pull up the PHM while releasing the small snap tabs on two corners of the socket.
Removing the screws in
the sequence of 4, 3, 2, 1
#4
#1
#2
#3
CPU Socket
Printed Triangle on Motherboard
After removing the screws,
lift the Processor Heatsink
Module off the CPU socket.
Figure 3-9. Removing the Processor Heatsink Module
33
WinFast GS2030 User's Manual
Memory Installation
Memory Support
The X11DPG-SN supports up to 2TB of DDR4-2666/2400/2133 3DS Load Reduced DIMM
(3DS LRDIMM), Load Reduced DIMM (LRDIMM), Registered DIMM (RDIMM), or Non-Vollatile
DIMM (NVDIMM) in 16 DIMM slots. Populating these slots with two DIMMs at a time will result
in interleaved memory, which will improve performance. The black DIMM slots are reserved
for future NVDIMM support.
Check the Leadtek website for possible updates to memory support.
Installing Memory
Begin by removing power from the system as described in Section 3.1.
1. Insert DIMM modules in the following order: For CPU1, begin with P1-DIMMA1, P1DIMMD1, P1-DIMMB1 then P1-DIMMF1, P1-DIMME1, P1-DIMMD1. For CPU2, begin
with P2-DIMMA1, P2-DIMMD1, P2-DIMMB1 then P2-DIMMF1, P2-DIMME1, P2DIMMD1. For the system to work properly, please use memory modules of the same
type and speed.
2. Push the release tabs outwards on both ends of the DIMM slot to unlock it.
3. Align the key of the DIMM module with the receptive point on the memory slot.
4. Align the notches on both ends of the module against the receptive points on the ends
of the slot.
Press both ends
straight down into
the memory slot.
Notches
Release Tabs
Figure 3-10. Installing DIMMs
Warning: In single-CPU configurations, memory must be installed in the DIMM slots associated
with the installed CPU.
Note: Visit the product page on the Leadtek website for possible updates to memory
support (system.leadtek.com).
34
Chapter 3: Maintenance and Component Installation
5. Use two thumbs together to press the notches on both ends of the module straight down
into the slot until the module snaps into place.
6. Press the release tabs to the lock positions to secure the DIMM module into the slot.
DIMM Removal
1. Reverse the steps above to remove the DIMM modules from the motherboard..
Caution: Exercise extreme caution when installing or removing memory modules to prevent
any possible damage to the DIMMs or slots.
DDR4 Memory Support for the Intel Xeon Scalable Processor
Speed (MT/s); Voltage (V); Slots per Channel (SPC) and DIMMs per Channel (DPC)
Type
Ranks
Per
DIMM
and Data
Width
4 Gb
RDIMM
SRx4
8 GB
RDIMM
SRx8
4 GB
RDIMM
DRx8
RDIMM
RDIMM 3Ds
LRDIMM
LRDIMM 3Ds
DIMM Capacity
(GB)
2 Slots per Channel
1DPC (1-DIMM per Channel)
2DPC (2-DIMM per Channel)
8 Gb
1.2 V
1.2 V
16 GB
2666
2666
8 GB
2666
2666
8 GB
16 GB
2666
2666
DRx4
16 GB
32 GB
2666
2666
QRX4
N/A
2H-64GB
2666
2666
8RX4
N/A
4H-128GB
2666
2666
QRx4
32 GB
64 GB
2666
2666
QRX4
N/A
2H-64GB
2666
2666
8Rx4
N/A
4H-128 GB
2666
2666
DDR4 Memory Support for the Intel Intel Xeon Scalable Processor
Speed (MT/s); Voltage (V); Slots per Channel (SPC) and DIMMs per Channel (DPC)
Type
Ranks
Per
DIMM
and Data
Width
4 Gb
8 Gb
1.2 V
RDIMM
SRx4
8 GB
16 GB
2666
RDIMM
SRx8
4 GB
8 GB
2666
RDIMM
DRx8
8 GB
16 GB
2666
RDIMM
DRx4
16 GB
32 GB
2666
QRX4
N/A
2H-64GB
2666
8RX4
N/A
4H-128GB
2666
QRx4
32 GB
64 GB
2666
QRX4
N/A
2H-64GB
2666
8Rx4
N/A
4H-128 GB
2666
RDIMM 3Ds
LRDIMM
LRDIMM 3Ds
DIMM Capacity
(GB)
1 Slot per Channel
1DPC (1-DIMM per Channel)
35
WinFast GS2030 User's Manual
DIMM Population Requirements
For optimal memory performance, follow the tables below when populating the DIMM slots.
Key Parameters for DIMM Configurations
Parameters
Possible Values
Number of Channels
1, 2, 3, 4, 5, or 6
Number of DIMMs per Channel
1DPC (1 DIMM Per Channel) or 2DPC (2 DIMMs Per Channel)
DIMM Type
RDIMM (w/ECC), LRDIMM, 3DS-LRDIMM
•
DIMM Construction
non-3DS RDIMM Raw Cards: A/B (2RX4), C (1RX4),
D (1RX8), E (2RX8)
•
•
•
3DS RDIMM Raw Cards: A/B (4RX4)
non-3DS LRDIMM Raw Cards: D/E (4RX4)
3DS LRDIMM Raw Cards: A/B (8RX4)
General Population Requirements
DIMM Mixing Rules
•
•
•
All DIMMs must be DDR4 DIMMs only.
X4 and X8 DIMMs can be mixed in the same channel.
Mixing of LRDIMMs and RDIMMs is not allowed in the same channel, across different channels, and across
different sockets.
•
Mixing of non-3DS and 3DS LRDIMM is not allowed in the same channel, across different channels, and across
different sockets.
Mixing of DIMM Types within a Channel
DIMM Types
RDIMM
LRDIMM
3DS LRDIMM
RDIMM
Allowed
Not Allowed
Not Allowed
LRDIMM
Not Allowed
Allowed
Not Allowed
3DS LRDIMM
Not Allowed
Not Allowed
Allowed
36
Chapter 3: Maintenance and Component Installation
Motherboard Battery
The motherboard uses non-volatile memory to retain system information when system power
is removed. This memory is powered by a lithium battery residing on the motherboard.
Replacing the Battery
Begin by removing power from the system as described in Section 3.1 and remove the cover
as described in Section 3.2.
1. Push aside the small clamp that covers the edge of the battery. When the battery is
released, lift it out of the holder.
2. To insert a new battery, slide one edge under the lip of the holder with the positive (+)
side facing up. Then push the other side down until the clamp snaps over it.
OR
Figure 3-11. Installing the Onboard Battery
Warning: There is a danger of explosion if the onboard battery is installed upside down (which
reverses its polarities). This battery must be replaced only with the same or an equivalent
type recommended by the manufacturer (CR2032).
Note: Handle used batteries carefully. Do not damage the battery in any way; a damaged
battery may release hazardous materials into the environment. Do not discard a used battery
in the garbage or a public landfill. Please comply with the regulations set up by your local
hazardous waste management agency to dispose of your used battery properly.
37
WinFast GS2030 User's Manual
3.4 Chassis Components
Hard Drives
The SC218GHTS has ten hot-swap 2.5" drive bays located at the front of the chassis.
The hard drives are mounted in drive carriers to simplify their installation and removal from
the chassis. (Both procedures may be done without removing power from the system.) These
carriers also help promote proper airflow for the drive bays. For this reason, even carriers
without drives must remain in the chassis.
Removing a Hot-Swap Drive Carrier
1. Push the release button on the carrier. This extends the carrier handle.
2. Swing the handle fully out.
3. Grasp the handle and use it to pull the drive carrier out of its bay.
Mounting a Drive in a Drive Carrier
1. To add a new drive, install it into the carrier with the printed circuit board side facing
down so that the mounting holes align with those in the carrier.
2. Secure the drive to the carrier with the screws provided, then push the carrier
completely into the drive bay. You should hear a *click* when the drive is fully inserted.
This indicates that the carrier has been fully seated and connected to the midplane,
which automatically makes the power and logic connections to the hard drive.
Removing a Drive from a Drive Carrier
1. Remove the screws that secure the hard drive to the carrier and separate the hard drive
from the carrier.
2. Replace the carrier back into the drive bay.
Note: Enterprise level hard disk drives are recommended for use in Leadtek chassis and
servers. For information on recommended HDDs, visit the Leadtek website.
38
Chapter 3: Maintenance and Component Installation
Graphics Processing Units
The 2029GP-TR supports up to six double-width GPU cards, which are mounted in brackets
to fit into the PCI-Express slots at the front and rear of the chassis. NVIDIA P40/P100/V100/
coprocessor GPUs are supported. The GPU cards may be pre-installed, see the procedure
below for replacing a GPU card must be replaced. See the NVIDIA website for more details
on the GPU specifications.
Installing GPUs
1. Identify the left and right brackets and graphics cards as illustrated.
2. Insert the GPU card into the bracket, aligning the mounting holes in the cards with those
in the brackets.
3. Secure each card to the bracket using the screws that are included for this purpose.
4. Carefully position each bracket in the chassis as illustrated, aligning the four mounting
holes in the top and side of each bracket with the corresponding mounting holes in the
chassis. Pay attention to the airflow arrows to install each card into the correct side of
the chassis
5. Secure the bracket to the chassis by using the screws provided.
6. After a GPU card is installed, you must connect it to one of the following power headers
on the serverboard: JPW3, JPW4, JPW5, JPW6 or JPW7.
Direction of Airflow
Right Side GPU
Bracket and Cards
Left Side GPU
Bracket and Cards
Figure 3-12. Installing GPUs
39
WinFast GS2030 User's Manual
Direction of Airflow
Side Screws
Left Side GPU Bracket and Cards
Direction of Airflow
Side Screws
Right Side GPU Bracket and Cards
Figure 3-13. Installing GPU Cards into the Left and Right GPU Brackets
Expansion Card Setup
The system supports the following PCI-Express expansion cards and an expansion card
bracket: Cards up to 10.5" in length are supported.
•
Six PCI-E 3.0 x16 add-on cards
•
One PCI-E 3.0 x8 (in x16) low-profile add-on card
40
Chapter 3: Maintenance and Component Installation
Low-Profile PCI-E Slots
Standard Size PCI-E Slots
Figure 3-14. Rear Expansion Card Slots
Installing a Full-Height Expansion Card
1. Begin by removing power from the system as described in Section 3.1 and remove the
cover as described in Section 3.2.
2. Confirm that you have the correct expansion card, riser card and expansion card bracket
for the chassis.
3. Remove the PCI-E slot covers at the rear of the chassis.
4. Secure the riser card onto the bracket with screws.
5. Insert the expansion card into the expansion slot on the riser card.
6. Place the expansion card bracket into the chassis as shown in the following figure, while
inserting the riser card into its appropriate slot on the serverboard.
7. Secure the expansion card bracket to the chassis with the three screws provided.
Figure 3-15. Installing Expansion Cards into the Expansion Card Bracket
41
WinFast GS2030 User's Manual
Figure 3-16. Installing the Expansion Card Bracket into the Chassis
Figure 3-17. Installing a Low-Profile Expansion Card
42
Chapter 3: Maintenance and Component Installation
System Cooling
Five 8-cm fans provide the cooling for the system. It is very important that the chassis top
cover is properly installed and making a good seal in order for the cooling air to circulate
properly through the chassis and cool the components.
System Fan Failure
Fan speed is controlled by system temperature by means of an IPMI setting. If a fan fails,
the remaining fans will ramp up to full speed. The system can continue to run with a failed
fan. Replace any failed fan at your earliest convenience with the same type and model.
Replacing a System Fan
1. With the power on, remove the chassis cover if necessary to determine which fan has
failed.
2. After determining the failed fan, remove power from the system as described in Section
3.1 and remove the cover as described in Section 3.2.
3. Remove the screws securing the fan housing to the floor of the chassis. See the
illustrations below to determine the location of the screws for the fan that is being
removed. Set these screws aside for later use.
Removing the Front Fans
Removing the Mid Fans
Removing the GPU Fan
Figure 3-18. Removing the Front, Mid and GPU Fans
43
WinFast GS2030 User's Manual
4. Lift the fan housing up and out of the chassis.
5. Disconnect the fan cable.
6. Examine the drawings below, then disassemble the fan housing by removing the front
and rear fan guards (A).
7. Reassemble the fan housing around the replacement fan as follows:
Front and GPU Fans
1. Clip the front and rear fan guards (A) into the left and right side clips (B)
A
B
A
B
Figure 3-19. Reassembling a Front or GPU Fan Housing
Mid Fans:
2. Slide the center clip (C) between the two fans. Clip the front and rear fan guards (A) to
the left and right side clips (B)
A
B
B
C
A
Figure 3-20. Reassembling the Mid Fan Housing
44
Chapter 3: Maintenance and Component Installation
3. Reconnect the cable to the replacement fan.
4. Replace the chassis cover and power cord, then power the system back on.
Air Shroud
Air shrouds concentrate airflow to maximize fan efficiency. The serverboard air shroud does
not require screws for installation. Each GPU card has its own air shroud.
Installing the Serverboard Air Shroud
1. Remove power from the system as described in Section 3.1 and remove the cover as
described in Section 3.2.
2. Ensure that the motherboard, CPU, heatsink and memory are all properly installed.
3. If necessary, move any cables that interfere with the air shroud placement.
4. Place the air shroud in the chassis. The air shroud fits just behind the fans in the fan
rack. Slide the air shroud into the grooves just behind the fan rack. Note that some
serverboards may require the air shroud to be modified to fit over the serverboard.
Figure 3-21. Installing the Air Shroud
45
WinFast GS2030 User's Manual
Power Supply
The system includes dual hot-plug 2000 Watt power modules. They automatically sense the
input voltage between 100v to 240v, and operate at that voltage. Note that different input
voltages will result in different maximum power output levels.
In the event of a power supply failure, the remaining power supply will automatically take
over.* The failed power module can then be replaced without powering-down the system with
the same model. Replacement modules can be ordered directly from Leadtek.
An amber light on the power supply is illuminated when the power is switched off. A green
light indicates that the power supply is operating.
Replacing the Power Supply
1. Push the release tab on the front of the failed power supply.
2. Grasp the handle of the power supply and pull it out of the power supply bay.
3. Push the new power supply module into the power bay until it clicks into the locked
position.
1
2
Figure 3-22. Removing/Replacing a Power Supply
46
Chapter 4: Motherboard Connections
Chapter 4
Motherboard Connections
This section describes the connections on the motherboard and provides pinout definitions.
Note that depending on how the system is configured, not all connections are required. The
LEDs on the motherboard are also described here. A serverboard layout indicating component
locations may be found in Chapter 1.
Please review the Safety Precautions in Appendix B before installing or removing components.
4.1 Power Connections
The main power connection on the X11DPG-SN must be connected to the power supply. The
wiring is included with the power supply.
to
•
8-pin Processor Power (JPWR2)
Main ATX Power
to
The power supply modules plug directly into the X11DPG-SN, so there is no cable connection
that needs to be made for main power. However you must also connect the 8-pin power
connectors (JPW1 - JPW4) to your power supply (see below) to provide power to the GPUs.
GPU Power Headers
JPW3-JPW7 are the 8-pin 12V DC power output for the GPUs.
GPU Power
Pin Definitions
Pin#
Definition
1-4
Ground
5-8
+12V
Required Connection
47
WinFast GS2030 User's Manual
4.2 Headers and Connectors
Fan Headers
Eight 4-pin fan headers (FAN1~6, FANA, FANB) are located on the motherboard to provide
CPU/system cooling. These 4-pin fan headers are backward compatible with traditional 3-pin
fans. Fan speed control is supported by a thermal management setting in the BMC (Baseboard
Management Controller) and is only available only when all 4-pin fans are used.
Fan Header
Pin Definitions
Pin#
Definition
1
Ground (Black)
2
+12V (Red)
3
Tachometer
4
PWM Control
TPM Header
The JTPM1 header is used to connect a Trusted Platform Module (TPM)/Port 80, which is
available from a third-party vendor. A TPM/Port 80 connector is a security device that supports
encryption and authentication in hard drives. It allows the motherboard to deny access if the
TPM associated with the hard drive is not installed in the system.
Trusted Platform Module/Port 80 Header
Pin Definitions
Pin#
Definition
Pin#
Definition
1
+3.3V
2
SPI_CS#
3
RESET#
4
SPI_MISO
5
SPI_CLK
6
GND
7
SPI_MOSI
8
9
+3.3V Stdby
10
SPI_IRQ#
RAID Key Header
A RAID Key header is located at JRK1 on the motherboard. The RAID key is used to support
NVMe RAID.
RAID Key Header
Pin Definitions
Pin#
Definition
1
Ground
2
PU 3.3V Stby
3
Ground
4
PCH RAID Key
48
Chapter 4: Motherboard Connections
SGPIO Header
The S-SGPIO1 (Serial General Purpose Input/Output) header is used to communicate with
the enclosure management chip on the backplane.
SGPIO Header
Pin Definitions
Pin#
Definition
Pin#
Definition
1
NC
2
NC
3
Ground
4
DATA Out
5
Load
6
Ground
7
Clock
8
NC
NC = No Connection
Chassis Intrusion
A Chassis Intrusion header is located at JL1 on the motherboard. Attach the appropriate cable
from the chassis to inform you of a chassis intrusion when the chassis is opened.
Chassis Intrusion
Pin Definitions
Pin#
Definition
1
Intrusion Input
2
Ground
BMC External I2C Header
A System Management Bus header for IPMI 2.0 is located at JIPMB1. Connect the appropriate
cable here to use the the I2C connection on your system.
External I2C Header
Pin Definitions
Pin#
Definition
1
Data
2
Ground
3
Clock
4
No Connection
Speaker Header
A speaker header is located on JD1. Close pins 1-2 of JD1 to use the onboard speaker.
Speaker Connector
Pin Definitions
Pin Setting
Definition
Pin 1
Power
Pin 2
Buzzer
49
WinFast GS2030 User's Manual
Serial Port
There is one COM connector (JCOM1) near the I/O back panel, next to the IPMI LAN
connector. The COM connector provides serial communication support.
VGA Port
The VGA connector (JVGA) is located below the JSIOM slot and next to JTPM1 connector.
Use this connection for VGA display.
NVMe Slots
Use the two NVMe slots (NVME1 and NVME2) to attach high-speed PCI-E storage devices.
I-SATA 3.0 and S-SATA 3.0 Ports
The X11DPG-SN has ten SATA 3.0 ports (I-SATA0-3, I-SATA4-7 and S-SATA0 and S-SATA1),
which are supported by the Intel C621 chipset. S-SATA0 can be used with Leadtek
SuperDOM, a yellow SATA DOM connector with power pins built in that does not require
external power cables. Leadtek SuperDOMs are backward-compatible with regular SATA
HDDs or SATA DOMs that need external power cables.
Control Panel
JF1 contains header pins for various control panel connections. See the figure below for the
pin locations and definitions of the control panel buttons and LED indicators.
All JF1 wires have been bundled into a single cable to simplify this connection. Make sure
the red wire plugs into pin 1 as marked on the motherboard. The other end connects to the
control panel PCB board.
1
2
PWR
Power Button
Ground
Reset
Reset Button
Ground
Power Fail LED
3.3V
UID LED
OH/Fan Fail LED
3.3V Stby
NIC2 Active LED
3.3V Stby
NIC1 Active LED
3.3V Stby
HDD LED
3.3V Stby
PWR LED
x
x
Ground
NMI
19
20
Figure 4-1. JF1: Control Panel Pins
50
Chapter 4: Motherboard Connections
Power Button
The Power Button connection is located on pins 1 and 2 of JF1. Momentarily contacting both
pins will power on/off the system. This button can also be configured to function as a suspend
button (with a setting in the BIOS - see Chapter 6). To turn off the power when the system
is in suspend mode, press the button for 4 seconds or longer.
Power Button
Pin Definitions (JF1)
Pin#
Definition
1
Signal
2
Ground
Reset Button
The Reset Button connection is located on pins 3 and 4 of JF1. Attach it to a hardware reset
switch on the computer chassis.
Reset Button
Pin Definitions (JF1)
Pin#
Definition
3
Reset
4
Ground
Power Fail LED
The Power Fail LED connection is located on pins 5 and 6 of JF1.
Power Fail LED
Pin Definitions (JF1)
Pin#
Definition
5
3.3V
6
PWR Supply Fail
51
WinFast GS2030 User's Manual
Fan Fail and UID LED
Connect an LED cable to pins 7 and 8 of JF1 to use the Overheat/Fan Fail LED connections.
The LED on pin 8 provides warnings of overheat or fan failure.
OH/Fan Fail Indicator
Status
OH/Fan Fail LED
Pin Definitions (JF1)
Status
Definition
Pin#
Definition
Off
Normal
7
Blue LED
On
Overheat
8
OH/Fan Fail LED
Flashing
Fan Fail
NIC1/NIC2 (LAN1/LAN2)
The NIC (Network Interface Controller) LED connection for LAN port 1 is located on pins 11
and 12 of JF1, and the LED connection for LAN Port 2 is on pins 9 and 10. Attach the NIC
LED cables here to display network activity.
LAN1/LAN2 LED
Pin Definitions (JF1)
Pin#
Definition
9
NIC2 Activity LED
10
NIC2 Link LED
11
NIC1 Activity LED
12
NIC1 Link LED
HDD LED
The HDD LED connection is located on pins 13 and 14 of JF1. Attach a cable to Pin 14 to
show hard drive activity status. Refer to the table below for pin definitions.
HDD LED
Pin Definitions (JF1)
Pin#
Definition
13
3.3V Standby
14
HDD Active
52
Chapter 4: Motherboard Connections
Power LED
The Power LED connection is located on pins 15 and 16 of JF1.
Power LED
Pin Definitions (JF1)
Pin#
Definition
15
3.3V Standby
16
Power LED
NMI Button
The non-maskable interrupt button header is located on pins 19 and 20 of JF1.
NMI Button
Pin Definitions (JF1)
Pin#
Definition
19
Control
20
Ground
4.3 Ports
Rear I/O Ports
See the figure below for the locations and descriptions of the various I/O ports on the rear
of the motherboard
2
1
3
4
Rear I/O Ports
No.
Description
No.
Description
1.
USB0 Port (USB 3.0)
3.
IPMI LAN Port
2.
USB1 Port (USB 3.0)
4.
Unit Identifier Switch
53
WinFast GS2030 User's Manual
Universal Serial Bus (USB) Ports
There are two USB 3.0 ports (USB0/1) on the I/O back panel.
Back Panel USB 0/1 (3.0)
Pin Definitions
Pin#
Definition
Pin#
Definition
A1
VBUS
B1
Power
A2
D-
B2
USB_N
A3
D+
B3
USB_P
A4
GND
B4
GND
A5
Stda_SSRX-
B5
USB3_RN
A6
Stda_SSRX+
B6
USB3_RP
A7
GND
B7
GND
A8
Stda_SSTX-
B8
USB3_TN
A9
Stda_SSTX+
B9
USB3_TP
Ethernet Port
A dedicated IPMI LAN port is located next to the USB 0/1 ports on the back panel. This GbE
Ethernet port accepts RJ45 type cables. Refer to the LED Indicator Section for LAN LED
information.
Unit Identifier Switch/UID LED Indicator
A Unit Identifier (UID) switch and a rear UID LED (LE1) are located on the I/O back panel. A
front UID switch connects to pins 7 & 8 of the front panel control (JF1). When you press the
front or the rear UID switch, both front and rear UID LEDs will be turned on. Press the UID
switch again to turn off the LED indicators. The UID indicators provide easy identification of
a system that may be in need of service.
Note: UID can also be triggered via IPMI. For more information on IPMI, please refer to the
IPMI User's Guide posted on our website.
UID LED
LED Indicator
LED Color
Definition
Blue: On
Unit Identified
54
Chapter 4: Motherboard Connections
4.4 Jumpers
Explanation of Jumpers
To modify the operation of the motherboard, jumpers are used to choose between optional
settings. Jumpers create shorts between two pins to change the function associated with it.
Pin 1 is identified with a square solder pad on the printed circuit board. See the motherboard
layout page for jumper locations.
Note: On a two-pin jumper, "Closed" means the jumper is on both pins and "Open" indicates
the jumper is either on only one pin or has been completely removed.
Connector
Pins
3
2
1
3
2
1
Jumper
Setting
CMOS Clear
JBT1 is used to clear CMOS, which will also clear any passwords. Instead of pins, this jumper
consists of contact pads to prevent accidentally clearing the contents of CMOS.
To Clear CMOS
1. First power down the system and unplug the power cord(s).
2. Remove the cover of the chassis to access the motherboard.
3. Remove the onboard battery from the motherboard.
4. Short the CMOS pads with a metal object such as a small screwdriver for at least four
seconds.
5. Remove the screwdriver (or shorting device).
6. Replace the cover, reconnect the power cord(s) and power on the system.
Notes: Clearing CMOS will also clear all passwords.
Do not use the PW_ON connector to clear CMOS.
JBT1 contact pads
55
WinFast GS2030 User's Manual
Manufacturing Mode Select
Close JPME2 to bypass SPI flash security and force the system to use the Manufacturing
Mode, which will allow you to flash the system firmware from a host server to modify system
settings.
Manufacturing Mode Select
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Normal (Default)
Pins 2-3
Manufacturing Mode
Watch Dog
JWD controls the Watch Dog function. Watch Dog is a monitor that can reboot the system
when a software application hangs. Jumping pins 1-2 will cause Watch Dog to reset the system
if an application hangs. Jumping pins 2-3 will generate a non-maskable interrupt signal for
the application that hangs. Watch Dog must also be enabled in BIOS.
The default setting is Reset.
Note: When Watch Dog is enabled, the user needs to write their own application software
to disable it.
Watch Dog
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Reset
Pins 2-3
NMI
Open
Disabled
VGA Enable/Disable
JPG1 allows you to enable or disable the VGA port that uses the onboard graphics controller.
The default setting is Enabled.
VGA Enable/Disable
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
56
Chapter 4: Motherboard Connections
BIOS Recovery
The default setting is on pins 1 and 2 of jumper JBR1 for normal operation (Normal). For
BIOS recovery, close pins 2-3.
BIOS Recovery
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Normal
Pins 2-3
BIOS Recovery
Management Engine (ME) Recovery
Use jumper JPME1 to select ME Firmware Recovery mode and limit resource allocation to only
essential system operation in order to maintain normal power operation and management. In
the single operation mode, online upgrade will be available via Recovery mode.
Manufacturer Mode
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Normal
Pins 2-3
ME Recovery
57
WinFast GS2030 User's Manual
4.5 LED Indicators
BMC Heartbeat LED
LEDM1 is the BMC heartbeat LED. When the LED is blinking green, BMC is functioning
normally.
Onboard Power LED Indicator
LED Color
Green:
Blinking
Definition
BMC Normal
Onboard Power LED
The Onboard Power LED is located at LE2 on the motherboard. When this LED is on, the
system is on. Be sure to turn off the system and unplug the power cord before removing or
installing components.
Onboard Power LED Indicator
LED Color
Off
Green
Definition
System Off (power cable
not connected)
System On
Dedicated IPMI LAN Port LEDs
A dedicated IPMI LAN port is located on the I/O backplane. The amber LED on the right
indicates activity, while the green LED on the left indicates the speed of the connection.
Unit ID LED
A rear UID LED indicator at LE1 is located near the UID switch on the back panel. This UID
indicator provides easy identification of a system in a rack.
UID LED Indicator
LED Color
Definition
Blue: On
Unit Identified
UID Switch
UID LED
58
Chapter 5: Software
Chapter 5
Software
After the hardware has been installed, you should install the Operating System (OS), configure
RAID settings and install the drivers. Necessary drivers and utilities may be found at
system.leadtek.com.
5.1 OS Installation
You must first configure RAID settings (if using RAID) before you install the Windows OS and
the software drivers. To configure RAID settings, please refer to the RAID Configuration User
Guides posted on our website at system.leadtek.com.
Installing the Windows OS for a RAID System
1. Insert Microsoft's Windows Setup DVD in the DVD drive and the system will start
booting up from the DVD.
2. Insert the USB stick containing Windows drivers to a USB port on the system.
Note: for older legacy OS's, please use a method to slipstream the drivers.
3. Select the partition on the drive in which to install Windows.
4. Browse the USB folder for the proper driver files.
5. Choose the RAID driver indicated in the Windows OS Setup screen, then choose the
hard drive in which you want to install it.
6. Once all devices are specified, continue with the installation.
7. After the Windows OS installation is completed, the system will automatically reboot.
Installing Windows to a Non-RAID System
1. Insert Microsoft's Windows OS Setup DVD in the DVD-ROM drive and the system will
start booting up from the DVD.
2. Continue with the installation. The Windows OS Setup screen will display.
3. From the Windows OS Setup screen, press the <Enter> key. The OS Setup will
automatically load all device files and then continue with the Windows installation.
4. After the installation has completed, the system will automatically reboot.
59
Chapter 6: BIOS
Chapter 6
BIOS
6.1 Introduction
This chapter describes the AMIBIOS™ Setup utility for the X11DPG-SN motherboards. The
BIOS is stored on a chip and can be easily upgraded using a flash program.
Note: Due to periodic changes to the BIOS, some settings may have been added
or deleted and might not yet be recorded in this manual. Please refer to the Manual
Download area of our website for any changes to BIOS that may not be reflected in
this manual.
Starting the Setup Utility
To enter the BIOS setup utility, press the <Delete> key while the system is booting-up. (In
most cases, the <Delete> key is used to invoke the BIOS setup screen. There are a few
cases when other keys are used, such as <F1>, <F2>, etc.) Each main BIOS menu option
is described in this manual.
The Main BIOS screen has two main frames. The left frame displays all the options that can
be configured. “Grayed-out” options cannot be configured. The right frame displays the key
legend. Above the key legend is an area reserved for a text message. When an option is
selected in the left frame, it is highlighted in white. Often a text message will accompany it.
(Note that BIOS has default text messages built in. We retain the option to include, omit, or
change any of these text messages.) Settings printed in Bold are the default values.
A "" indicates a submenu. Highlighting such an item and pressing the <Enter> key will open
the list of settings within that submenu.
The BIOS setup utility uses a key-based navigation system called hot keys. Most of these
hot keys (<F1>, <F10>, <Enter>, <ESC>, <Arrow> keys, etc.) can be used at any time during
the setup navigation process.
63
WinFast GS2030 User's Manual
6.2 Main Setup
When you first enter the AMI BIOS setup utility, you will enter the Main setup screen. You can
always return to the Main setup screen by selecting the Main tab on the top of the screen. The
Main BIOS setup screen is shown below. The following Main menu items will be displayed:
WinFast GS2030
System Date/System Time
Use this item to change the system date and time. Highlight System Date or System Time
using the arrow keys. Enter new values using the keyboard. Press the <Tab> key or the arrow
keys to move between fields. The date must be entered in Day MM/DD/YYYY format. The
time is entered in HH:MM:SS format.
Note: The time is in the 24-hour format. For example, 5:30 P.M. appears as 17:30:00.
The date's default value is 01/01/2014 after RTC reset.
WinFast GS2030
BIOS Version
This item displays the version of the BIOS ROM used in the system.
Build Date
This item displays the date when the version of the BIOS ROM used in the system was built.
CPLD Version
This item displays the version of the CPLD (Complex-Programmable Logical Device) used
in the system.
64
Chapter 6: BIOS
Memory Information
Total Memory
This item displays the total size of memory available in the system.
Memory Speed
This item displays the default speed of the memory modules installed in the system.
65
WinFast GS2030 User's Manual
6.3 Advanced Setup Configurations
Use the arrow keys to select the Advanced submenu and press <Enter> to access the
submenu items:
Warning: Take Caution when changing the Advanced settings. An incorrect value, an incorrect
DRAM frequency, or an incorrect BIOS timing setting may cause the system to malfunction.
When this occurs, restore the setting to the manufacture default setting.
Boot Feature
Quiet Boot
Use this feature to select the screen between displaying POST messages or the OEM logo
at bootup. Select Disabled to display the POST messages. Select Enabled to display the
OEM logo instead of the normal POST messages. The options are Disabled and Enabled.
Note: POST message is always displayed regardless of the item setting.
Option ROM Messages
Use this feature to set the display mode for the Option ROM. Select Keep Current to use
the current AddOn ROM display setting. Select Force BIOS to use the Option ROM display
mode set by the system BIOS. The options are Force BIOS and Keep Current.
Bootup NumLock State
Use this feature to set the Power-on state for the Numlock key. The options are On and Off.
66
Chapter 6: BIOS
Wait For 'F1' If Error
Select Enabled to force the system to wait until the 'F1' key is pressed if an error occurs. The
options are Disabled and Enabled.
Interrupt 19 Capture
Interrupt 19 is the software interrupt that handles the boot disk function. When this item is
set to Immediate, the ROM BIOS of the host adaptors will "capture" Interrupt 19 at bootup
immediately and allow the drives that are attached to these host adaptors to function as
bootable disks. If this item is set to Postponed, the ROM BIOS of the host adaptors will not
capture Interrupt 19 immediately and allow the drives attached to these adaptors to function
as bootable devices at bootup. The options are Immediate and Postponed.
Re-try Boot
When EFI (Expansible Firmware Interface) Boot is selected, the system BIOS will automatically
reboot the system from an EFI boot device after an initial boot failure. Select Legacy Boot to
allow the BIOS to automatically reboot the system from a Legacy boot device after an initial
boot failure. The options are Disabled, Legacy Boot, and EFI Boot.
Power Configuration
Watch Dog Function
Select Enabled to allow the Watch Dog timer to reboot the system when it is inactive for more
than 5 minutes. The options are Disabled and Enabled.
Power Button Function
This feature controls how the system shuts down when the power button is pressed. Select 4
Seconds Override for the user to power off the system after pressing and holding the power
button for 4 seconds or longer. Select Instant Off to instantly power off the system as soon
as the user presses the power button. The options are Instant Off and 4 Seconds Override.
Restore on AC Power Loss
Use this feature to set the power state after a power outage. Select Power-Off for
the system power to remain off after a power loss. Select Power-On for the system
power to be turned on after a power loss. Select Last State to allow the system
to resume its last power state before a power loss. The options are Power-On,
Stay-Off and Last State.
67
WinFast GS2030 User's Manual
CPU Configuration
Warning: Setting the wrong values in the following sections may cause the system to malfunc tion.
Processor Configuration
The following CPU information will be displayed:
•
Processor BSP Revision
•
Processor Socket
•
Processor ID
•
Processor Frequency
•
Processor Max Ratio
•
Processor Min Ratio
•
Microcode Revision
•
L1 Cache RAM
•
L2 Cache RAM
•
L3 Cache RAM
•
Processor 0 Version
•
Processor 1 Version
Hyper-Threading (ALL)
Select Enable to use Intel Hyper-Threading Technology to enhance CPU performance. The
options are Disable and Enable.
Execute Disable Bit (Available if supported by the OS & the CPU)
Select Enable to enable Execute Disable Bit support which will allow the processor to
designate areas in the system memory where an application code can execute and where
it cannot, thus preventing a worm or a virus from flooding illegal codes to overwhelm the
processor, damaging the system during a virus attack. The options are Disable and Enable.
(Refer to Intel and Microsoft websites for more information.)
68
Chapter 6: BIOS
Intel Virtualization Technology
Select Enable to use Intel Virtualization Technology which will allow the I/O device assignments
to be directly reported to the VMM (Virtual Memory Management) through the DMAR ACPI
tables. This feature offers fully-protected I/O resource-sharing across the Intel platforms,
providing the user with greater reliability, security and availability in networking and datasharing. The settings are Disable and Enable.
PPIN Control
Select Unlock/Enable to use the Protected-Processor Inventory Number (PPIN) in the system.
The options are Unlock/Disable and Unlock/Enable.
Hardware Prefetcher (Available when supported by the CPU)
If this feature is set to Enable, the hardware prefetcher will prefetch streams of data and
instructions from the main memory to the Level 2 (L2) cache to improve CPU performance.
The options are Enable and Disable.
Adjacent Cache Prefetch (Available when supported by the CPU)
Select Enable for the CPU to prefetch both cache lines for 128 bytes as comprised. Select
Disable for the CPU to prefetch both cache lines for 64 bytes. The options are Enable and
Disable.
Note: Please power off and reboot the system for the changes you've made to take
effect. Please refer to Intel’s website for detailed information.
DCU Streamer Prefetcher (Available when supported by the CPU)
If this item is set to Enable, the DCU (Data Cache Unit) streamer prefetcher will prefetch data
streams from the cache memory to the DCU (Data Cache Unit) to speed up data accessing
and processing for CPU performance enhancement. The options are Enable and Disable.
DCU IP Prefetcher
If this item is set to Enable, the IP prefetcher in the DCU (Data Cache Unit) will prefetch IP
addresses to improve network connectivity and system performance. The options are Enable
and Disable.
LLC Prefetch
If this feature is set to Enable, LLC (hardware cache) prefetching on all threads will be
supported. The options are Disable and Enable.
Extended APIC (Extended Advanced Programmable Interrupt Controller)
Based on the Intel Hyper-Threading technology, each logical processor (thread) is assigned
256 APIC IDs (APIDs) in 8-bit bandwidth. When this feature is set to Enable, the APIC ID
will be expanded from 8 bits to 16 bits to provide 512 APIDs to each thread to enhance CPU
performance. The options are Disable and Enable.
69
WinFast GS2030 User's Manual
AES-NI
Select Enable to use the Intel Advanced Encryption Standard (AES) New Instructions (NI) to
ensure data security. The options are Disable and Enable.
Advanced Power Management Configuration
CPU P State Control
SpeedStep (PStates)
EIST (Enhanced Intel SpeedStep Technology) allows the system to automatically adjust
processor voltage and core frequency in an effort to reduce power consumption and heat
dissipation. Please refer to Intel’s website for detailed information. The options are Disable
and Enable.
EIST PSD Function (Available when SpeedStep is set to Enable)
Use this item to configure the processor's P-State coordination settings. During a P-State,
the voltage and frequency of the processor will be reduced when it is in operation. This
makes the processor more energy efficient, resulting in further energy gains. The options
are HW_ALL, SW_ALL and SW-ANY.
Turbo Mode (Available when SpeedStep is set to Enable)
Select Enable for processor cores to run faster than the frequency specified by the
manufacturer. The options are Disable and Enable.
Hardware PM (Power Management) State Control
Hardware P-States
If this feature is set to Disable, hardware will choose a P-state setting for the system based
on an OS request. If this feature is set to Native Mode, hardware will choose a P-state
setting based on OS guidance. If this feature is set to Native Mode with No Legacy Support,
hardware will choose a P-state setting independently without OS guidance. The options
are Disable, Native Mode, Out of Band Mode, and Native Mode with No Legacy Support.
CPU C State Control
Autonomous Core C-State
Select Enable to support Autonomous Core C-State control which will allow the processor
core to control its C-State setting automatically and independently. The options are Disable
and Enable.
70
Chapter 6: BIOS
CPU C6 Report
Select Enable to allow the BIOS to report the CPU C6 state (ACPI C3) to the operating
system. During the CPU C6 state, power to all caches is turned off. The options are Disable,
Enable and Auto.
Enhanced Halt State (C1E)
Select Enable to enable "Enhanced Halt State" support, which will significantly reduce the
CPU's power consumption by minimizing CPU's clock cycles and reduce voltage during a
"Halt State." The options are Disable and Enable.
Package C State Control
Package C State
Use this feature to set the limit on the C-State package register. The options are C0/1 state,
C2 state, C6 (non-Retention) state, C6 (Retention) state, No Limit, and Auto.
Chipset Configuration
Warning: Setting the wrong values in the following sections may cause the system to malfunction.
North Bridge
This feature allows the user to configure the settings for the Intel North Bridge.
UPI (Ultra Path Interconnect) Configuration
This section displays the following UPI General Configuration information:
•
Number of CPU
•
Number of IIO
•
Current UPI Link Speed
•
Current UPI Link Frequency
•
UPI Global MMIO Low Base/Limit
•
UPI Global MMIO High Base/Limit
•
UPI PCI-E Configuration Base/Size
71
WinFast GS2030 User's Manual
Degrade Precedence
Use this feature to select the degrading precedence option for Ultra Path Interconnect
connections. Select Topology Precedent to degrade UPI features if system options are in
conflict. Select Feature Precedent to degrade UPI topology if system options are in conflict.
The options are Topology Precedence and Feature Precedence.
Link L0p Enable
Select Enable to enable Link L0p. The options are Disable, Enable, and Auto.
Link L1 Enable
Select Enable to enable Link L1 (Level 1 link). The options are Disable, Enable, and Auto.
IO Directory Cache
Select Enable for the IODC (I/O Directory Cache) to generate snoops instead of generating
memory lockups for remote IIO (InvIToM) and/or WCiLF (Cores). Select Auto for the IODC to
generate snoops (instead of memory lockups) for WCiLF (Cores). The options are Disable,
Auto, Enable for Remote InvItoM Hybrid Push, InvItoM AllocFlow, Enable for Remote
InvItoM Hybrid AllocNonAlloc, and Enable for Remote InvItoM and Remote WViLF.
Isoc Mode
Select Enable to enable Isochronous support to meet QoS (Quality of Service) requirements.
This feature is especially important for Virtualization Technology. The options are Disable,
Enable, and Auto.
Memory Configuration
Enforce POR
Select POR to enforce POR restrictions for DDR4 memory frequency and voltage
programming. The options are POR and Disable.
Memory Frequency
Use this feature to set the maximum memory frequency for onboard memory modules. The
options are Auto, 1866, 2000, 2133, 2200, 2400, 2600, and 2666.
Data Scrambling for NVDIMM
Select Enable to enable data scrambling for onboard NVDIMM memory to enhance system
performance and security. The options are Auto, Disable, and Enable.
Data Scrambling for DDR4
Select Enable to enable data scrambling for DDR4 memory to enhance system performance
and security. The options are Auto, Disable, and Enable.
72
Chapter 6: BIOS
tCCD_L Relaxation
If this feature is set to Enable, SPD (Serial Presence Detect) will override tCCD_L ("Column
to Column Delay-Long", or “Command to Command Delay-Long” on the column side.) If
this feature is set to Disable, tCCD_L will be enforced based on the memory frequency.
The options are Auto Enable and Disable.
Enable ADR
Select Enable for ADR (Automatic Diagnostic Repository) support to enhance memory
performance. The options are Disable and Enable.
Memory Topology
This item displays the information of onboard memory modules as detected by the BIOS.
•
P1 DIMMA1
•
P1 DIMMA2
•
P2 DIMMB1
•
P2 DIMMC1
•
P1 DIMMD1
•
P1 DIMMD2
•
P1 DIMME1
•
P1 DIMMF1
•
P1 DIMMA1
•
P1 DIMMA2
•
P1 DIMMB1
•
P1 DIMMC1
•
P1 DIMMD1
•
P1 DIMMD2
•
P1 DIMME1
•
P1 DIMMF1
73
WinFast GS2030 User's Manual
Memory RAS (Reliability_Availability_Serviceability) Configuration
Use this submenu to configure the following Memory RAS settings.
Static Virtual Lockstep Mode
Select Enable to support Static Virtual Lockstep mode to enhance memory performance.
The options are Disable and Enable.
Mirror Mode
Select Enable to set all 1LM/2LM memory installed in the system on the mirror mode, which
will create a duplicate copy of data stored in the memory to increase memory security, but
it will reduce the memory capacity into half. The options are Disable, Mirror Mode 1LM
and Mirror Mode 2LM.
Memory Rank Sparing
Select Enable to support memory-rank sparing to optimize memory performance. The
options are Disable and Enable.
Note: This item will not be available when memory mirror mode is enabled.
Correctable Error Threshold
Use this item to enter the threshold value for correctable memory errors. The default setting
is 10.
SDDC Plus One
Select Enable for SDDC (Single Device Data Correction) Plus One support, which will
increase the reliability and serviceability of your system memory. The options are Disable
and Enable.
ADDDC (Adaptive Double Device Data Correction) Sparing
Select Enable for ADDDC sparing support to enhance memory performance. The options
are Disable and Enable.
Patrol Scrub
Patrol Scrubbing is a process that allows the CPU to correct correctable memory errors
detected in a memory module and send the corrections to the requestor (the original
source). When this item is set to Enable, the IO hub will read and write back one cache line
every 16K cycles if there is no delay caused by internal processing. By using this method,
roughly 64 GB of memory behind the IO hub will be scrubbed every day. The options are
Disable and Enable.
Patrol Scrub Interval
Use this item to specify the number of hours (between 0 to 24) required for the system to
complete a full patrol scrubbing. Enter 0 for patrol scrubbing to be performed automatically.
The default setting is 24.
74
Chapter 6: BIOS
Note: This item is hidden when Patrol Scrub item is set to Disable.
IIO Configuration
EV DFX (Device Function On-Hide) Features
When this feature is set to Enable, the EV_DFX Lock Bits that are located in a processor
will always remain clear during electric tuning. The options are Disable and Enable.
CPU1 Configuration/CPU2 Configuration
IOU0 (IIO PCIe Br1)
This item configures the PCI-E Bifuraction setting for a PCI-E port specified by the user.
The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
IOU1 (IIO PCIe Br2)
This item configures the PCI-E Bifuraction setting for a PCI-E port specified by the user.
The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
IOU2 (IIO PCIe Br3)
This item configures the PCI-E Bifuraction setting for a PCI-E port specified by the user.
The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
MCP0 (IIO PCIe Br4)
This item configures the PCI-E Bifuraction setting for a PCI-E port specified by the user.
The options are x16 and Auto.
MCP1 (IIO PCIe Br5)
This item configures the PCI-E Bifuraction setting for a PCI-E port specified by the user.
The options are x16 and Auto.
Socket 0 PCI-E Br0D00F0 - Port 0/DMI to Socket 0 PcieBr5D00F0 - MCP 1
(Available for CPU 1 Configuration only)
Link Speed
This item configures the link speed of a PCI-E port specified by the user. The options
are Auto, Gen 1 (Generation 1) (2.5 GT/s), Gen 2 (Generation 2) (5 GT/s), and Gen 3
(Generation 3) (8 GT/s)
The following information will be displayed as well:
•
PCI-E Port Link Status
•
PCI-E Port Link Max
•
PCI-E Port Link Speed
75
WinFast GS2030 User's Manual
PCI-E Port Max (Maximum) Payload Size (Available for CPU 1 Configuration only)
Select Auto for the system BIOS to automatically set the maximum payload value for a
PCI-E device specified by to user to enhance system performance. The options are 128B,
256B and Auto.
IOAT Configuration
Disable TPH (TLP Processing Hint)
TPH is used for data-tagging with a destination ID and a few important attributes. It can
send critical data to a particular cache without writing through to memory. Select No in this
item for TLP Processing Hint support, which will allow a "TPL request" to provide "hints"
to help optimize the processing of each transaction occurred in the target memory space.
The options are No and Yes.
Prioritize TPH (TLP Processing Hint)
Select Yes to prioritize the TPL requests that will allow the "hints" to be sent to help facilitate
and optimize the processing of certain transactions in the system memory. The options are
Enable and Disable.
Relaxed Ordering
Select Enable to enable Relaxed Ordering support which will allow certain transactions to
violate the strict-ordering rules of PCI and to be completed prior to other transactions that
have already been enqueued. The options are Disable and Enable.
Intel VT for Directed I/O (VT-d)
Intel® VT for Directed I/O (VT-d)
Select Enable to use Intel Virtualization Technology support for Direct I/O VT-d by reporting
the I/O device assignments to the VMM (Virtual Machine Monitor) through the DMAR
ACPI tables. This feature offers fully-protected I/O resource sharing across Intel platforms,
providing greater reliability, security and availability in networking and data-sharing. The
options are Enable and Disable.
Interrupt Remapping
Select Enable for Interrupt Remapping support to enhance system performance. The
options are Enable and Disable.
PassThrough DMA
Select Enable for the Non-Iscoh VT-d engine to pass through DMA (Direct Memory Access)
to enhance system performance. The options are Enable and Disable.
76
Chapter 6: BIOS
ATS
Select Enable to enable ATS (Address Translation Services) support for the Non-Iscoh VT-d
engine to enhance system performance. The options are Enable and Disable.
Posted Interrupt
Select Enable to support VT_D Posted Interrupt which will allow external interrupts to be
sent directly from a direct-assigned device to a client machine in non-root mode to improve
virtualization efficiency by simplifying interrupt migration and lessening the need of physical
interrupts. The options are Enable and Disable.
Coherency Support (Non-Isoch)
Select Enable for the Non-Iscoh VT-d engine to pass through DMA (Direct Memory Access)
to enhance system performance. The options are Enable and Disable.
Intel® VMD Technology
Intel® VMD for Onboard NVMe
Intel® VMD for Onboard NVMe
Onboard NVMe Mode
Select Legacy Mode for the onboard NVMe devices to support Legacy Mode. The options are Legacy Mode and the VMD Mode. When VMD Mode is selected, the following
options become available:
•
P1_NVMe0 VMD - The options are Disable and Enable
•
P1_NVMe1 VMD - The options are Disable and Enable
•
Hot Plug Capable - The options are Disable and Enable
IIO-PCIE Express Global Options
The section allows the user to configure the following PCI-E global options:
PCE-E Hot Plug
Select Enable to support Hot-plugging for the selected PCI-E slots which will allow the user
to replace the devices installed in the slots without shutting down the system. The options
are Disable, Enable, Auto and Manual.
PCI-E Completion Timeout (Global)
Use this item to select the PCI-E Completion Time-out settings. The options are Yes, No,
and Per-Port.
77
WinFast GS2030 User's Manual
South Bridge
The following South Bridge information will display:
•
USB Module Version
•
USB Devices
Legacy USB Support
Select Enabled to support onboard legacy USB devices. Select Auto to disable legacy support
if there are no legacy USB devices present. Select Disable to have all USB devices available
for EFI applications only. The options are Enabled, Disabled and Auto.
XHCI Hand-Off
This is a work-around solution for operating systems that do not support XHCI (Extensible
Host Controller Interface) hand-off. The XHCI ownership change should be claimed by the
XHCI driver. The options are Enabled and Disabled.
Port 60/64 Emulation
Select Enabled for I/O port 60h/64h emulation support, which in turn, will provide complete
legacy USB keyboard support for the operating systems that do not support legacy USB
devices. The options are Disabled and Enabled.
Port 61h Bit-4 Emulation
Select Enabled for I/O Port 61h-Bit 4 emulation support to enhance system performance. The
options are Disabled and Enabled.
Install Windows 7 USB Support
Select Enabled to install the Windows 7 USB utility to support legacy USB devices for Windows
7 systems. The options are Disabled and Enabled.
Server ME (Management Engine) Configuration
This feature displays the following system ME configuration settings.
Operational Firmware Version
Backup Firmware Version
Recovery Firmware Version
ME Firmware Status #1
ME Firmware Status #2
Current State
Error Code
78
Chapter 6: BIOS
SATA Configuration
When this submenu is selected, the AMI BIOS automatically detects the presence of the SATA
devices that are supported by the Intel PCH chip and displays the following items:
SATA Controller
This item enables or disables the onboard SATA controller supported by the Intel PCH chip.
The options are Disable and Enable.
Configure SATA as (Available when the item above: SATA Controller is set to
enabled)
Select AHCI to configure a SATA drive specified by the user as an AHCI drive. Select RAID
to configure a SATA drive specified by the user as a RAID drive. The options are AHCI and
RAID. (Note: This item is hidden when the SATA Controller item is set to Disabled.)
SATA HDD Unlock
Select Enable to unlock SATA HDD password in the OS. The options are Disable and Enable.
SATA/sSATA RAID Boot Select
This feature allows the user to decide which controller should be used for system boot. The
options are None, SATA Controller, sSATA Controller and Both.
Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power use of the
SATA link. The controller will put the link in a low power mode during an extended period of
I/O inactivity, and will return the link to an active state when I/O activity resumes. The options
are Disable and Enable.
SATA RAID Option ROM/UEFI Driver (Available when the item "Configure SATA as"
is set to "RAID")
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy driver for
system boot. The options are Legacy ,EFI and Disable.
SATA Port 0 - SATA Port 7
Hot Plug
Select Enable to support Hot-plugging for the device installed on a selected SATA port
which will allow the user to replace the device installed in the slot without shutting down
the system. The options are Enable and Disabled.
Spin Up Device
On an edge detect from 0 to 1, set this item to allow the SATA device installed on the SATA
port specified by the user to start a COMRESET initialization. The options are Enable and
Disable.
79
WinFast GS2030 User's Manual
SATA Device Type
Use this item to specify if the device installed on the SATA port selected by the user should
be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk Drive
and Solid State Drive.
sSATA Configuration
When this submenu is selected, AMI BIOS automatically detects the presence of the sSATA
devices that are supported by the sSATA controller and displays the following items:
sSATA Controller
This item enables or disables the onboard sSATA controller supported by the Intel SCU. The
options are Enable and Disable.
Configure sSATA as
Select AHCI to configure an sSATA drive specified by the user as an AHCI drive. Select RAID
to configure an sSATA drive specified by the user as a RAID drive. The options are AHCI
and RAID. (Note: This item is hidden when the sSATA Controller item is set to Disabled.)
SATA HDD Unlock
Select Enable to unlock sSATA HDD password in the OS. The options are Disable and Enable.
SATA/sSATA RAID Boot Select (Available when the item "Configure SATA as" is set
to "RAID")
This feature allows the user to decide which controller should be used for system boot. The
options are None, SATA Controller, sSATA Controller, and Both.
Aggressive Link Power Management
When this item is set to Enable, the sSATA AHCI controller manages the power use of the
SATA link. The controller will put the link in a low power mode during an extended period of
I/O inactivity, and will return the link to an active state when I/O activity resumes. The options
are Disable and Enable.
sSATA RAID Option ROM/UEFI Driver (Available when the item "Configure SATA as"
is set to "RAID")
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy driver for
system boot. The options are Legacy, EFI and Disable.
sSATA Port 0 - sSATA Port 5
Hot Plug
Select Enable to support Hot-plugging for the device installed on an sSATA port selected by
the user which will allow the user to replace the device installed in the slot without shutting
down the system. The options are Disable and Enabled.
80
Chapter 6: BIOS
Spin Up Device
On an edge detect from 0 to 1, set this item to allow the sSATA device installed on the
sSATA port specified by the user to start a COMRESET initialization. The options are
Enable and Disable.
sSATA Device Type
Use this item to specify if the device installed on the sSATA port specified by the user
should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard
Disk Drive and Solid State Drive.
PCIe/PCI/PnP Configuration
The following PCI information will be displayed:
•
PCI Bus Driver Version
•
PCI Devices Common Settings:
Above 4G Decoding (Available if the system supports 64-bit PCI decoding)
Select Enabled to decode a PCI device that supports 64-bit in the space above 4G Address.
The options are Disabled and Enabled.
SR-IOV Support (Available if the system supports Single-Root Virtualization)
Select Enabled for Single-Root IO Virtualization support. The options are Disabled and
Enabled.
MMIOHBase
Use this item to select the base memory size according to memory-address mapping for the
IO hub. The base memory size must be between 4032G to 4078G. The options are 56T,
48T, 24T, 16T, 4T, and 1T.
MMIO High Granularity Size
Use this item to select the high memory size according to memory-address mapping for the
IO hub. The options are 1G, 4G, 16G, 64G, 256G, and 1024G.
PCI PERR/SERR Support
Use this feature to enable or disable the runtime event for SERR (System Error)/ PERR (PCI/
PCI-E Parity Error). The options are Disabled and Enabled.
Maximum Read Request
Select Auto for the system BIOS to automatically set the maximum size for a read request
for a PCI-E device to enhance system performance. The options are Auto, 128 Bytes, 256
Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
81
WinFast GS2030 User's Manual
MMCFG Base
This feature determines the lowest MMCFG (Memory-Mapped Configuration) base assigned
to PCI devices. The options are 1G, 1.5G, 1.75G. 2G, 2.25G, and 3G.
VGA Priority
Use this item to select the graphics device to be used as the primary video display for system
boot. The options are Auto, Onboard and Offboard.
PCI Devices Option ROM Settings
Onboard NVME1/NVME2 OPROM
Select EFI to allow the user to boot the computer using an EFI (Expansible Firmware Interface)
device installed on the NVME connector specified by the user. Select Legacy to allow the
user to boot the computer using a legacy device installed on the NVME connector specified
by the user. The options are Disabled, Legacy and EFI.
CPU1 Slot 1 PCI-E 3.0 X16
The options are Disabled, Legacy and EFI.
CPU2 Slot 2 PCI-E 3.0 X16
The options are Disabled, Legacy and EFI.
CPU1 Slot 3 PCI-E 3.0 X16
The options are Disabled, Legacy and EFI.
CPU2 Slot 4 PCI-E 3.0 X16
The options are Disabled, Legacy and EFI.
CPU2 Slot 5 PCI-E 3.0 X8
The options are Disabled, Legacy and EFI.
Onboard Video Option ROM
Use this feature to select the Onboard Video Option ROM type. The options are Disabled,
Legacy and EFI.
Network Stack Configuration
Network Stack
Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified Extensible
Firmware Interface) for network stack support. The options are Disabled and Enabled.
*If "Network Stack" is set to Enabled, the following items will display:
82
Chapter 6: BIOS
Ipv4 PXE Support
Select Enabled to enable Ipv4 PXE boot support. If this feature is disabled, it will not create
the Ipv4 PXE boot option. The options are Disabled and Enabled.
Ipv4 HTTP Support
Select Enabled to enable Ipv4 HTTP boot support. If this feature is disabled, it will not create
the Ipv4 HTTP boot option. The options are Disabled and Enabled.
Ipv6 PXE Support
Select Enabled to enable Ipv6 PXE boot support. If this feature is disabled, it will not create
the Ipv6 PXE boot option. The options are Disabled and Enabled.
Ipv6 HTTP Support
Select Enabled to enable Ipv6 HTTP boot support. If this feature is disabled, it will not create
the Ipv6 HTTP boot option. The options are Disabled and Enabled.
PXE Boot Wait Time
Use this feature to select the wait time to press the <ESC> key to abort the PXE boot. The
default is 0.
Media Detect Time
Use this feature to select the wait time in seconds for the BIOS ROM to detect the LAN media
(Internet connection or LAN port). The default is 1.
Super IO Configuration
Super IO Chip AST2500
Serial Port 1 Configuration
Serial Port
Select Enabled to enable the onboard serial port specified by the user. The options are
Disabled and Enabled.
Device Settings
This item displays the base I/O port address and the Interrupt Request address of a serial
port specified by the user.
Note: This item is hidden when Serial Port 1 is set to Disabled.
83
WinFast GS2030 User's Manual
Change Settings
This feature specifies the base I/O port address and the Interrupt Request address of Serial
Port 1. Select Auto for the BIOS to automatically assign the base I/O and IRQ address to a
serial port specified.
The options for Serial Port 1 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5, 6, 7, 9,
10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12); (IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10,
11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).
Serial Port 2 Configuration
Serial Port
Select Enabled to enable the onboard serial port specified by the user. The options are
Enabled and Disabled.
Device Settings
This item displays the base I/O port address and the Interrupt Request address of a serial
port specified by the user.
Note: This item is hidden when Serial Port 1 is set to Disabled.
Change Settings
This feature specifies the base I/O port address and the Interrupt Request address of Serial
Port 2. Select Auto for the BIOS to automatically assign the base I/O and IRQ address to a
serial port specified. The options for Serial Port 2 are Auto, (IO=2F8h; IRQ=3), (IO=3F8h;
IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12); (IO=3E8h; IRQ=3,
4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).
Serial Port 2 Attribute
Select SOL to use COM Port 2 as a Serial_Over_LAN (SOL) port for console redirection.
The options are SOL and COM.
Serial Port Console Redirection
COM 1 Console Redirection
Select Enabled to enable COM Port 1 for Console Redirection, which will allow a client
machine to be connected to a host machine at a remote site for networking. The options are
Disabled and Enabled.
*If the item above set to Enabled, the following items will become available for configuration:
84
Chapter 6: BIOS
Console Redirection Settings (for COM1)
Terminal Type
Use thid feature to select the target terminal emulation type for Console Redirection.
Select VT100 to use the ASCII Character set. Select VT100+ to add color and function
key support. Select ANSI to use the Extended ASCII Character Set. Select VT-UTF8 to
use UTF8 encoding to map Unicode characters into one or more bytes. The options are
VT100, VT100+, VT-UTF8 and ANSI.
Bits Per second
Use this feature to set the transmission speed for a serial port used in Console Redirection.
Make sure that the same speed is used in the host computer and the client computer. A
lower transmission speed may be required for long and busy lines. The options are 9600,
19200, 38400, 57600 and 115200 (bits per second).
Data Bits
Use this feature to set the data transmission size for Console Redirection. The options are
7 (Bits) and 8 (Bits).
Parity
A parity bit can be sent along with regular data bits to detect data transmission errors.
Select Even if the parity bit is set to 0, and the number of 1's in data bits is even. Select
Odd if the parity bit is set to 0, and the number of 1's in data bits is odd. Select None if you
do not want to send a parity bit with your data bits in transmission. Select Mark to add a
mark as a parity bit to be sent along with the data bits. Select Space to add a Space as a
parity bit to be sent with your data bits. The options are None, Even, Odd, Mark and Space.
Stop Bits
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial
data communication. Select 2 Stop Bits if slower devices are used. The options are 1 and 2.
Flow Control
Use this feature to set the flow control for Console Redirection to prevent data loss caused
by buffer overflow. Send a "Stop" signal to stop sending data when the receiving buffer
is full. Send a "Start" signal to start sending data when the receiving buffer is empty. The
options are None and Hardware RTS/CTS.
VT-UTF8 Combo Key Support
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100 terminals.
The options are Disabled and Enabled.
85
WinFast GS2030 User's Manual
Recorder Mode
Select Enabled to capture the data displayed on a terminal and send it as text messages
to a remote server. The options are Disabled and Enabled.
Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Disabled and
Enabled.
Legacy OS Redirection Resolution
Use this feature to select the number of rows and columns used in Console Redirection
for legacy OS support. The options are 80x24 and 80x25.
Putty KeyPad
This feature selects Function Keys and KeyPad settings for Putty, which is a terminal
emulator designed for the Windows OS. The options are VT100, LINUX, XTERMR6, SCO,
ESCN, and VT400.
Redirection After BIOS Post
Use this feature to enable or disable legacy Console Redirection after BIOS POST. When
the option-Bootloader is selected, legacy Console Redirection is disabled before booting
the OS. When the option-Always Enable is selected, legacy Console Redirection remains
enabled upon OS bootup. The options are Always Enable and Bootloader.
COM2/SOL (Serial-Over-LAN)
Console Redirection (for SOL/COM2)
Select Enabled to use the SOL port for Console Redirection. The options are Disabled and
Enabled.
*If the item above set to Enabled, the following items will become available for user's
configuration:
Console Redirection Settings (for COM2/SOL)
Use this feature to specify how the host computer will exchange data with the client
computer, which is the remote computer used by the user.
Terminal Type
Use this feature to select the target terminal emulation type for Console Redirection.
Select VT100 to use the ASCII Character set. Select VT100+ to add color and function
key support. Select ANSI to use the Extended ASCII Character Set. Select VT-UTF8 to
use UTF8 encoding to map Unicode characters into one or more bytes. The options are
VT100, VT100+, VT-UTF8 and ANSI,.
86
Chapter 6: BIOS
Bits Per Second
Use this feature to set the transmission speed for a serial port used in Console Redirection.
Make sure that the same speed is used in the host computer and the client computer. A
lower transmission speed may be required for long and busy lines. The options are 9600,
19200, 38400, 57600 and 115200 (bits per second).
Data Bits
Use this feature to set the data transmission size for Console Redirection. The options are
7 (Bits) and 8 (Bits).
Parity
A parity bit can be sent along with regular data bits to detect data transmission errors.
Select Even if the parity bit is set to 0, and the number of 1's in data bits is even. Select
Odd if the parity bit is set to 0, and the number of 1's in data bits is odd. Select None if you
do not want to send a parity bit with your data bits in transmission. Select Mark to add a
mark as a parity bit to be sent along with the data bits. Select Space to add a Space as a
parity bit to be sent with your data bits. The options are None, Even, Odd, Mark and Space.
Stop Bits
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial
data communication. Select 2 Stop Bits if slower devices are used. The options are 1 and 2.
Flow Control
Use this feature to set the flow control for Console Redirection to prevent data loss caused
by buffer overflow. Send a "Stop" signal to stop sending data when the receiving buffer
is full. Send a "Start" signal to start data-sending when the receiving buffer is empty. The
options are None and Hardware RTS/CTS.
VT-UTF8 Combo Key Support
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100 terminals.
The options are Disabled and Enabled.
Recorder Mode
Select Enabled to capture the data displayed on a terminal and send it as text messages
to a remote server. The options are Disabled and Enabled.
Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Disabled and
Enabled.
Legacy OS Redirection Resolution
Use this feature to select the number of rows and columns used in Console Redirection
for legacy OS support. The options are 80x24 and 80x25.
87
WinFast GS2030 User's Manual
Putty KeyPad
This feature selects Function Keys and KeyPad settings for Putty, which is a terminal
emulator designed for the Windows OS. The options are VT100, LINUX, XTERMR6, SCO,
ESCN, and VT400.
Redirection After BIOS Post
Use this feature to enable or disable legacy Console Redirection after BIOS POST
(Power-On Self-Test). When this feature is set to Bootloader, legacy Console Redirection
is disabled before booting the OS. When this feature is set to Always Enable, legacy
Console Redirection remains enabled upon OS boot. The options are Always Enable and
Bootloader.
Legacy Console Redirection Settings
Legacy Console Redirection Settings
Use the feature to select the COM port to display redirection of Legacy OS and Legacy
OPROM messages. The options are COM1 are COM2/SOL.
Serial Port for Out-of-Band Management/Windows Emergency Management
Services (EMS)
The submenu allows the user to configure Console Redirection settings to support Out-ofBand Serial Port management.
Console Redirection (for EMS)
Select Enabled to use a COM port selected by the user for EMS Console Redirection. The
options are Disabled and Enabled.
*If the item above set to Enabled, the following items will become available for user's
configuration:
EMS Console Redirection Settings
Out-of-Band Management Port
The feature selects a serial port in a client server to be used by the Windows Emergency
Management Services (EMS) to communicate with a remote host server. The options are
COM1 (Console Redirection) and COM2/SOL (Console Redirection).
Terminal Type
Use this feature to select the target terminal emulation type for Console Redirection.
Select VT100 to use the ASCII character set. Select VT100+ to add color and function
key support. Select ANSI to use the extended ASCII character set. Select VT-UTF8 to use
UTF8 encoding to map Unicode characters into one or more bytes. The options are VT100,
VT100+, VT-UTF8 and ANSI.
88
Chapter 6: BIOS
Bits Per Second
This feature sets the transmission speed for a serial port used in Console Redirection.
Make sure that the same speed is used in both host computer and the client computer. A
lower transmission speed may be required for long and busy lines. The options are 9600,
19200, 57600, and 115200 (bits per second).
Flow Control
Use this feature to set the flow control for Console Redirection to prevent data loss caused
by buffer overflow. Send a "Stop" signal to stop data-sending when the receiving buffer
is full. Send a "Start" signal to start data-sending when the receiving buffer is empty. The
options are None, Hardware RTS/CTS, and Software Xon/Xoff.
The setting for each these features is displayed:
Data Bits, Parity, Stop Bits
ACPI Settings
Use this feature to configure Advanced Configuration and Power Interface (ACPI) power
management settings for your system.
NUMA Support (Available when the OS supports this feature)
Select Enabled to enable Non-Uniform Memory Access support to enhance system
performance. The options are Disabled and Enabled.
WHEA Support
Select Enabled to support the Windows Hardware Error Architecture (WHEA) platform and
provide a common infrastructure for the system to handle hardware errors within the Windows
OS environment to reduce system crashes and to enhance system recovery and health
monitoring. The options are Disabled and Enabled.
High Precision Timer
Select Enabled to activate the High Precision Event Timer (HPET) that produces periodic
interrupts at a much higher frequency than a Real-time Clock (RTC) does in synchronizing
multimedia streams, providing smooth playback and reducing the dependency on other
timestamp calculation devices, such as an x86 RDTSC Instruction embedded in the CPU.
The High Performance Event Timer is used to replace the 8254 Programmable Interval Timer.
The options are Disabled and Enabled.
89
WinFast GS2030 User's Manual
Trusted Computing (Available when a TPM device is installed
and detected by the BIOS)
Device Select
The options are TPM 1.2, TPM 2.0 and Auto.
TXT Support
Select Enabled to enable Intel Trusted Execution Technology (TXT) support to enhance
system security and data integrity. The options are Disabled and Enabled.
Note 1: If the option for this item (TXT Support) is set to Enabled, be sure to disable
EV DFX (Device Function On-Hide) support for the system to work properly. (EV DFX
is under "IIO Configuration" in the "Chipset/North Bridge" submenu).
Intel® Virtual RAID on CPU
When this submenu is selected and the RAID devices are detected, the BIOS screen displays
the following items:
Intel® VROC with VMD Technology 5.2.0.1029
No RAID volumes on the system
No Intel VMD Controllers on the sy
90
Chapter 6: BIOS
6.4 Event Logs
Use this feature to configure Event Log settings.
Change SMBIOS Event Log Settings
Enabling/Disabling Options
SMBIOS Event Log
Select Enabled to enable SMBIOS (System Management BIOS) Event Logging during system
boot. The options are Disabled and Enabled.
Erasing Settings
Erase Event Log
Select Enabled to erase all error events in the SMBIOS (System Management BIOS) log
before an event logging is initialized at bootup. The options are No, Yes, Next Reset, and
Yes, Next Reset.
When Log is Full
Select Erase Immediately to immediately erase all errors in the SMBIOS event log when the
event log is full. Select Do Nothing for the system to do nothing when the SMBIOS event log
is full. The options are Do Nothing and Erase Immediately.
91
WinFast GS2030 User's Manual
SMBIOS Event Log Standard Settings
Log System Boot Event
Select Enabled to log system boot events. The options are Enabled and Disabled.
MECI (Multiple Event Count Increment)
Enter the increment value for the multiple event counter. Enter a number between 1 to 255.
The default setting is 1.
METW (Multiple Event Count Time Window)
This item is used to determine how long (in minutes) should the multiple event counter wait
before generating a new event log. Enter a number between 0 to 99. The default setting is 60.
Note: Please reboot the system for the changes to take effect.
Customer Options
Log OEM Codes
Select Enabled to log the EFI Status codes as OEM codes if these codes have not been
converted to Legacy. The options are Disabled and Enabled.
Convert OEM Codes
Select Enabled to convert the EFI Status codes to standard SMBIOS codes. Please note that
this option is not available for all EFI Status codes. The options are Disabled and Enabled.
Note: Please reboot the system for the changes to take effect.
View System Event Log
This item allows the user to view the event in the system event log. Select this item and press
<Enter> to view the status of an event in the log. The following categories are displayed:
Date/Time/Error Code/Severity
92
Chapter 6: BIOS
6.5 IPMI
Use this feature to configure Intelligent Platform Management Interface (IPMI) settings.
When you select this submenu and press the <Enter> key, the following information will
display:
•
IPMI Firmware Revision: This item indicates the IPMI firmware revision used in your system.
•
Status of BMC: This item indicates the status of the BMC (Baseboard Management Controller) installed in your system.
System Event Log
Enabling/Disabling Options
SEL Components
Select Enabled for all system event logging at bootup. The options are Disabled and Enabled.
Erasing Settings
Erase SEL
Select Yes, On next reset to erase all system event logs upon next system reboot. Select
Yes, On every reset to erase all system event logs upon each system reboot. Select No to
keep all system event logs after each system reboot. The options are No, Yes, On next reset,
and Yes, On every reset.
93
WinFast GS2030 User's Manual
When SEL is Full
This feature allows the user to determine what the BIOS should do when the system event
log is full. Select Erase Immediately to erase all events in the log when the system event log
is full. The options are Do Nothing and Erase Immediately.
Custom EFI Logging Options
Log EFI Status Codes
Select EFI (Extensible Firmware Interface) Status Codes to log EFI status codes. Select Error
Codes to log EFI error codes. Select Progress Code to log the EFI progress code. Select
both to log both EFI error codes and progress codes. The options are Disabled, Both, Error
code and Progress code.
Note: After making changes on a setting, be sure to reboot the system for the changes
to take effect.
BMC Network Configuration
The following items will be displayed:
•
IPMI LAN Selection: This item displays the IPMI LAN setting. The default setting is Failover.
•
IPMI Network Link Status: This item displays the IPMI Network Link status. The default
setting is Shared LAN.
•
Current Configuration Address Source: This item displays the source of the current IPMI
LAN address. The default setting is CHCP (Dynamic Host Configuration Protocol) .
•
Station IP Address: This item displays the Station IP address for this computer. This should
be in decimal and in dotted quad form (i.e., 192.168.10.253).
•
Subnet Mask: This item displays the sub-network that this computer belongs to. The value
of each three-digit number separated by dots should not exceed 255.
•
Station MAC Address: This item displays the Station MAC address for this computer. Mac
addresses are 6 two-digit hexadecimal numbers.
•
Gateway IP Address: This item displays the Gateway IP address for this computer. This
should be in decimal and in dotted quad form (i.e., 192.168.10.253).
•
VLAN: This item displays the status of VLAN support.
Update IPMI LAN Configuration
Select Yes for the BIOS to implement all IP/MAC address changes at the next system boot.
The options are No and Yes. If this option is set to Yes, the following items will display:
94
Chapter 6: BIOS
IPMI LAN Selection
Use this feature to select the type of the IPMI LAN. The options are Dedicated, Shared,
and Failover.
VLAN
Select Enabled to enable IPMI VLAN function support. The options are Enabled and
Disabled.
Configuration Address Source
Use this item to select the IP address source for this computer. If Static is selected, you will
need to know the IP address of this computer and enter it to the system manually in the field.
If DHCP is selected, AMI BIOS will search for a DHCP (Dynamic Host Configuration Protocol)
server attached to the network and request the next available IP address for this computer.
The options are Static and DHCP.
95
WinFast GS2030 User's Manual
6.6 Security Settings
This menu allows the user to configure the following security settings for the system.
Administrator Password
Use this feature to set the administrator password which is required to enter the BIOS setup
utility. The length of the password should be from 3 characters to 20 characters long.
User Password
Use this feature to set the user password which is required to enter the BIOS setup utility.
The length of the password should be from 3 characters to 20 characters long.
Password Check
Select Setup for the system to check for a password at Setup. Select Always for the system
to check for a password at bootup or upon entering the BIOS Setup utility. The options are
Setup and Always.
Secure Boot
When you select this submenu and press the <Enter> key, the following items will display:
•
System Mode
•
Secure Boot
•
Vendor Keys
96
Chapter 6: BIOS
Attempt Secure Boot
If this item is set to Enabled, Secure Boot will be activated when a Platform Key (PK) is
entered. A Platform Key is a security key used to manage the security settings of the platform
firmware used in your system. The options are Disabled and Enabled.
Secure Boot Mode
Use this feature to select the desired secure boot mode for the system. The options are
Standard and Custom.
CSM Support
Compatibility Support Module (CSM) allows for legacy BIOS compatibility by emulating a
BIOS environment. The options are Disabled and Enabled.
Key Management
Provision Factory Default Keys
Select Enabled to install all manufacturer default keys for the following system security
settings. The options are Disabled and Enabled.
Install Factor Default Keys
Select Yes to install all manufacturer defaults for the following system security settings. The
options are Yes and No.
Enroll EFI Image
Select this item and press <Enter> to select an EFI (Extensible Firmware Interface) image
for the system to operate in Secure Boot mode.
Save All Secure Boot Variables
This feature allows the user to set and save the secure boot key variables specified by the
user.
Secure Boot Variables
Secure Boot Variable/Size/Key#/Key Sources
Platform Key (PK)
This feature allows the user to enter and configure a set of values to be used as a platform
firmware key for the system. This set of values also indicate the size, the keys numbers,
and the key source of the Platform Key. The options are Save to File, Set New, and Erase.
97
WinFast GS2030 User's Manual
Key Exchange Keys
This feature allows the user to enter and configure a set of values to be used as a KeyExchange-Keys for the system. This set of values also indicate the size, the keys numbers,
and the key source of the Key-Exchange-Keys. The options are Save to File , Set New,
Append and Erase.
Authorized Signatures
This feature allows the user to enter and configure a set of values to be used as Authorized
Signatures for the system. This set of values also indicate the size, the keys numbers, and
the key source of the Authorized Signatures. The options are Save to File, Set New, Append
and Erase.
Forbidden Signatures
This feature allows the user to enter and configure a set of values to be used as Forbidden
Signatures for the system. This set of values also indicate the size, the keys numbers, and
the key source of the Forbidden Signatures. The options are Save to File, Set New, Append
and Erase.
Authorized TimeStamps
This feature allows the user to set and save the timestamps for Authorized Signatures to
indicate when these signatures were entered into the system. The options are Set New and
Append.
OsRecovery Signatures
This feature allows the user to set and save the Authorized Signatures used for OS recovery.
The options are Set New and Append.
98
Chapter 6: BIOS
6.7 Boot Settings
Use this feature to configure Boot Settings:
Boot Mode Select
Use this feature to select the type of devices that the system is going to boot from. The options
are Legacy, UEFI (Unified Extensible Firmware Interface) and Dual.
Fixed Boot Order Priorities
This feature prioritizes the order of a bootable device from which the system will boot. Press
<Enter> on each entry from top to bottom to select devices.
When the item above -"Boot Mode Select" is set to Dual (default), the following items will be
displayed for configuration:
•
Boot Option #1 - Boot Option #17
When the item above -"Boot Mode Select" is set to Legacy, the following items will be display
for configuration:
•
Boot Option #1 - Boot Option #8
When the item above -"Boot Mode Select" is set to UEFI, the following items will be display
for configuration:
•
Boot Option #1 - Boot Option #9
99
WinFast GS2030 User's Manual
Add New Boot Option
This feature allows the user to add a new boot option to the boot priority features for your
system.
Add Boot Option
Use this item to specify the name for the new boot option.
Path for Boot Option
Use this feature to enter the path for the new boot option in the format fsx:\path\filename.efi.
Boot Option File Path
Use this feature to specify the file path for the new boot option.
Create
After the name and the file path for the boot option are set, press <Enter> to create the
new boot option in the boot priority list.
Delete Boot Option
Use this feature to select a boot device to delete from the boot priority list.
Delete Boot Option
Use this feature to remove an EFI boot option from the boot priority list.
Delete Driver Option (Currently Unavailable)
Use this item to select a boot driver to delete from the boot priority list.
Delete Drive Option
Select the target boot driver to delete from the boot priority list.
UEFI Application Boot Priorities
Boot Option #1
Set the system boot order.
100
Chapter 6: BIOS
6.8 Save & Exit
Select the Save & Exit tab from the BIOS setup screen to configure the settings below.
Save Options
Discard Changes and Exit
Select this option to quit the BIOS setup without making any permanent changes to the
system configuration and reboot the computer. Select Discard Changes and Exit from the
Exit menu and press <Enter>.
Save Changes and Reset
When you have completed the system configuration changes, select this option to leave the
BIOS setup utility and reboot the computer for the new system configuration parameters to
take effect. Select Save Changes and Exit from the Exit menu and press <Enter>.
Save Changes
When you have completed the system configuration changes, select this option to save all
changes made. This will not reset (reboot) the system.
Discard Changes
Select this option and press <Enter> to discard all the changes and return to the AMI BIOS
setup utility.
101
WinFast GS2030 User's Manual
Default Options
Restore Optimized Defaults
To set this feature, select Restore Defaults from the Exit menu and press <Enter> to load
manufacturer default settings which are intended for maximum system performance but not
for maximum stability.
Save As User Defaults
To set this feature, select Save as User Defaults from the Exit menu and press <Enter>. This
enables the user to save any changes to the BIOS setup for future use.
Restore User Defaults
To set this feature, select Restore User Defaults from the Exit menu and press <Enter>. Use
this feature to retrieve user-defined settings that were saved previously.
Boot Override
This feature (UEFI: Built-in EFI Shell) allows the user to override the Boot priorities sequence
in the Boot menu, and immediately boot the system with a device specified by the user instead
of the one specified in the boot list. This is a one-time override.
102
Appendix A: BIOS Error Codes
Appendix A
BIOS Error Codes
A-1 BIOS Error Beep (POST) Codes
During the POST (Power-On Self-Test) routines, which are performed each time the system
is powered on, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue the boot-up
process. The error messages normally appear on the screen.
Fatal errors are those which will not allow the system to continue the boot-up procedure. If
a fatal error occurs, you should consult with your system manufacturer for possible repairs.
These fatal errors are usually communicated through a series of audible beeps. The numbers
on the fatal error list (on the following page) correspond to the number of beeps for the
corresponding error. All errors listed, with the exception of Beep Code 8, are fatal errors.
BIOS Error Beep (POST) Codes
Beep Code
Error Message
Description
1 short
Refresh
Circuits have been reset (Ready to power up)
5 short, 1 long
Memory error
No memory detected in system
5 long, 2 short
Display memory read/write error
Video adapter missing or with faulty memory
1 long continuous
System OH
System overheat condition
103
WinFast GS2030 User's Manual
Appendix B
Standardized Warning Statements for AC
Systems
B.1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of
situations which have the potential for bodily injury. Should you have questions or experience
difficulty, contact Leadtek 's Technical Support department for assistance. Only certified
technicians should attempt to install or configure components.
Read this appendix in its entirety before installing or configuring components in the Leadtek
chassis.
Warning Definition
Warning! This warning symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards involved
with electrical circuitry and be familiar with standard practices for preventing accidents.
警告の定義
この警告サインは危険を意味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分意识到触电
的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结尾的声明号码找到此设
备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸電的危險，
並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號碼找到相關的翻譯說明
內容。
105
Appendix B: Standardized Warning Statements
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen
führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer
Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen
Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen
Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät
ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de
manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese
con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia
encontrará el número que le ayudará a encontrar el texto traducido en el apartado de
traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES.
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement,
soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les
procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance
des traductions des avertissements figurant dans les consignes de sécurité traduites qui
accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque
avertissement.
CONSERVEZ CES INFORMATIONS.
‫תקנון הצהרות אזהרה‬
‫ על מנת להזהיר את המשתמש מפני חבלה‬,‫הצהרות הבאות הן אזהרות על פי תקני התעשייה‬
‫ יש ליצור קשר עם מחלקת תמיכה‬,‫ במידה ויש שאלות או היתקלות בבעיה כלשהי‬.‫פיזית אפשרית‬
.‫ טכנאים מוסמכים בלבד רשאים להתקין או להגדיר את הרכיבים‬.‫טכנית של סופרמיקרו‬
.‫יש לקרוא את הנספח במלואו לפני התקנת או הגדרת הרכיבים במארזי סופרמיקרו‬
106
WinFast GS2030 User's Manual
. ٌ ‫ك ً ا و ﺔﻟﺎﺣ ف ٌ ع ﺰﻫﺰﻟا ﺬاﻫ ٌة ﺬﺴﺟ ﺔﺎﺑﺻا ف ﺐﺒﺴﺘﺗ ﯨﺄ ي ٌ ز ﺬﺤﺗ! ﺰﻄﺧ‬
‫يﻌﻫ ﻳﺄ ﲆﻋ لﻮﻌﺗ ﯨﺄ ﻞﺒﻗ ٌﺰاﺋﺬوﻟا ﻲﻋ ةﻮﺟ‬،‫ا ال ﺰﺎﻃﺧﻮﻟﺎﺑ ﻦﻠﻋ ﲆﻋ ﺬات‬
‫ة ئﺑﺎﻟﻜﻬﺰ ٍا‬
‫ة ﺎئﻘﯩﻟا ﺎتﺳاروﻮﻟﺎﺑ ٌة ادر ﲆﻋ ﻳ ٍﻮ ع ﻮﻟ ٌ ﺎدثﯩﺣ ﻳﺄ ﻊﯩﻗو‬
‫ا ﻟﺐا ﻗﻦر مﺳﺘﺨﺬا ٍ ﺻ ﻟﻮا ٌى ﻫ ف ﯩﺺًز ﺗﺤﺬ ﻛﻞ ٌة ﺎ ٌﺗﻬﺎﺟﻮﺗﺰ ﻟﻠﻌﺜﯩﺮ‬
안전을 위한 주의사항
경고!
이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수 있는
상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와 관련된
위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준 작업절차를 준수해 주시기
바랍니다.
해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를 참조하십시오
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel
kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn
van de bij een elektrische installatie betrokken risico's en dient u op de hoogte te zijn van de
standaard procedures om ongelukken te voorkomen. Gebruik de nummers aan het eind van
elke waarschuwing om deze te herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
Installation Instructions
Warning! Read the installation instructions before connecting the system to the power
source.
設置手順書
システムを電源に接続する前に、設置手順書をお読み下さい。
警告
将此系统连接电源前,请先阅读安装说明。
警告
將系統與電源連接前，請先閱讀安裝說明。
107
Appendix B: Standardized Warning Statements
Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen.
¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.
.‫יש לקרוא את הוראות התקנה לפני חיבור המערכת למקור מתח‬
‫اقر إرشادات الرتكيب قبل توصيل النظام إىل مصدر للطاقة‬
시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.
Circuit Breaker
Warning! This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.
サーキット・ブレーカー
この製品は、短絡（過電流）保護装置がある建物での設置を前提としています。
保護装置の定格が250 V、20 Aを超えないことを確認下さい。
警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电流不大于
250V,20A。
警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電流不大於
250V,20A。
108
WinFast GS2030 User's Manual
Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw.
Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung
nicht mehr als: 250 V, 20 A beträgt.
¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del
edificio. Asegúrese de que el dispositivo de protección no sea superior a: 250 V, 20 A.
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de
l'installation électrique du local. Vérifiez que le courant nominal du dispositif de protection
n'est pas supérieur à :250 V, 20 A.
‫יחשמל קצר עתלמני במבנים קנתהמות הגנה על מךמסת זה צרמו‬. ‫כי לוודא שי‬
250VDC, 20A- ‫מ יותר לא הוא יהחשמל הקצר מפני המגן המכשיר‬
‫ﰲ ﺗﺜﺒﻴﺘﻬﺎ ﺗﻢ ﻟﺘﻲا ةﻟﻘﺼراﺋﺮاوﻟﺪا ﻣﻪ ﻳﺖﻟﺤاا ﺛﺎﻣﻌﺪ ﻋﲆ ﻳﻌﺘﻤﺪ ﳌﻨﺘﺞا اﻫﺬ‬
‫ﳌﺒﻨﻰا‬
20A, 250V : ‫ﻣﻦ ﻛرأ ﻟﻴﺲ يﻗﺎﻟﻮا زﻟﺠﻬﺎا ﺗﻘﻴﻴﻢ ﻧﺄ ﻣﻦ ﻛﺪﺗﺄ‬
경고!
이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다.
보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지 않도록 해야 합니다.
Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische
installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 250V, 20A.
109
Appendix B: Standardized Warning Statements
Power Disconnection Warning
Warning! The system must be disconnected from all sources of power and the power
cord removed from the power supply module(s) before accessing the chassis interior
to install or remove system components.
電源切断の警告
システムコンポーネントの取り付けまたは取り外しのために、
シャーシー内部にアクセスするには、
システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り外す必要が
あります。
警告
在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。
警告
在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。
Warnung
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel getrennt sein,
das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es auf den Chassisinnenraum
zurückgreift, um Systemsbestandteile anzubringen oder zu entfernen.
¡Advertencia!
El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado
de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para
instalar o para quitar componentes de sistema.
Attention
Le système doit être débranché de toutes les sources de puissance ainsi que de son cordon
d'alimentation secteur avant d'accéder à l'intérieur du chassis pour installer ou enlever des
composants de systéme.
‫אזהרה מפני ניתוק חשמלי‬
‫!אזהרה‬
‫יש לנתק את המערכת מכל מקורות החשמל ויש להסיר את כבל החשמלי מהספק‬
‫לפני גישה לחלק הפנימי של המארז לצורך התקנת או הסרת רכיבים‬.
110
WinFast GS2030 User's Manual
‫داﻣﺪا ةﺣﺪو ﻣﻦ ءﺑﺎﻧﻜﻬﺮا ﺳﻬﻚ ﻧﺖازإو ﻗﺖﻧﻄﺎا ردﻣﺼﺎ ﺟﻤﻴﻊ ﻣﻦ وﻧﻨﻈﺎا ﻓﺼﻢ ﺠﺐﻳ‬
‫ﻗﺒﻢ ﻗﺖﻧﻄﺎا‬
‫زﻟﺠﻬﺎا ثﻣﻜﯩﻨﺎ ﻧﺖازإ وأ ﻧﺘﺜﺒﻴﺞ ﻧﻬﻬﻴﻜﻢ ﺧﻬﻴﺖاﻧﺪا ﻃﻖمﻨﺎا ﯨﺈ ﻧﯩﺼﯩﻞا‬
경고!
시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에 반드시 전원
공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야 합니다.
Waarschuwing
Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren of
verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle stroomkabels
aangesloten op de voeding(en) van de behuizing te verwijderen
Equipment Installation
Warning! Only trained and qualified personnel should be allowed to install, replace,
or service this equipment.
機器の設置
トレーニングを受け認定された人だけがこの装置の設置、交換、
またはサービスを許可されていま
す。
警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。
警告
只有經過受訓且具資格人員才可安裝、更換與維修此設備。
Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,
qualifiziertem Personal gestattet werden.
¡Advertencia!
Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
111
Appendix B: Standardized Warning Statements
Attention
Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de
ces équipements à des personnels qualifiés et expérimentés.
!‫אזהרה‬
.‫ להחליף את הציוד או לתת שירות עבור הציוד‬,‫צוות מוסמך בלבד רשאי להתקין‬
‫واملدربيه لتزكيب واستبدال أو خدمة هذا الجهاس يجب أن يسمح فقط للمىظفيه املؤهليه‬
경고!
훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수 있습니다.
Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door geschoold en
gekwalificeerd personeel.
Restricted Area
Warning! This unit is intended for installation in restricted access areas. A restricted
access area can be accessed only through the use of a special tool, lock and key, or
other means of security. (This warning does not apply to workstations).
アクセス制限区域
このユニットは、
アクセス制限区域に設置されることを想定しています。
アクセス制限区域は、特別なツール、鍵と錠前、
その他のセキュリティの手段を用いてのみ出入りが
可能です。
警告
此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和钥匙或其它
安全手段进出的场所。
警告
此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙或其他安全
方式才能進入的區域。
112
WinFast GS2030 User's Manual
Warnung
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen. Der Zutritt
zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und Schlüssel oder einer
sonstigen Sicherheitsvorkehrung möglich.
¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido. Sólo puede
obtenerse acceso a una de estas áreas mediante la utilización de una herramienta especial,
cerradura con llave u otro medio de seguridad.
Attention
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une zone d'accès
réservé n'est possible qu'en utilisant un outil spécial, un mécanisme de verrouillage et une
clé, ou tout autre moyen de sécurité.
‫לתמוגב שהיג עם זורא‬
!‫זהרהא‬
‫שהיג לתהגב בהם ששי יםזוראב היחידה את קיןלהת שי‬. ‫זרתבע ניתנת שהיהג‬
(.‫מפתח) דבלב טחהאב יכל‬, ‫' וכד עולמנ‬
. ‫ﺏ ﻛﻧﺗﺭ ﺓﻧﯩﺣﺫﺍ ﮬﮭﺫ ﺗﺧﺻﯾﺹ ُ ﺗﻡ ﺓﺭﻣﺣظﻭ ﻁﻘﻣﻧﺎ ﻑ ﮬﺎ‬
‫ﺗﺎﺻﺦ أﺩﺍﺓ ﺫﺍﻭﺧﺗﺎﺱ ﺍﻟﻠﺦ ﻧﻡ ﻁﻘﻑ ﻭﺭﺓظﺣﻡ ﺗﻘﻁﻧﻡ ﺇن ﻟﯩﺻﯩﺎن ﻧك‬
‫ َﻡ‬٬
‫ﻩ ﻭﺱ أ أﻭ ُ ﺍﺣﺗﻔﻭﻡ ﻣﻔﻕ ﺍﻣﺎﻷﻟﻣن ﺭﯾﺄﺥ ﺕ‬
경고!
이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및 키,
또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.
Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang. Toegang tot
dergelijke gebieden kunnen alleen verkregen worden door gebruik te maken van speciaal
gereedschap, slot en sleutel of andere veiligheidsmaatregelen.
113
Appendix B: Standardized Warning Statements
Battery Handling
Warning! There is the danger of explosion if the battery is replaced incorrectly. Replace
the battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメーカーが推
奨する型、
または同等のものを使用下さい。使用済電池は製造元の指示に従って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电
池。请按制造商的说明处理废旧电池。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按
照製造商的說明指示處理廢棄舊電池。
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur
durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten
Batterien nach den Anweisungen des Herstellers.
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une
pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées
conformément aux instructions du fabricant.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la
batería exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante.
Desechar las baterías gastadas según las instrucciones del fabricante.
!‫אזהרה‬
‫ יש להחליף‬.‫קיימת סכנת פיצוץ של הסוללה במידה והוחלפה בדרך לא תקינה‬
.‫את הסוללה בסוג התואם מחברת יצרן מומלצת‬
.‫סילוק הסוללות המשומשות יש לבצע לפי הוראות היצרן‬
114
WinFast GS2030 User's Manual
‫ﻓﻌﻠﻴﻞ ﺻﺤﻴﺤﺔ ﻏر ﻳﻘﺔﺑﻄﺮ ﻳﺔرﻟﺒﻄﺎا ﻻﺳﺤﺒﺬا ﻟﺔﺣﺎ ﰲ رﻧﻔﺠﺎا ﻣﻦ ﺧﻄﺮ كﻫﻨﺎ‬
‫ﻳﺔرﻟﺒﻄﺎا ﻻﺳﺤﺒﺬا‬
‫ﳌﺼﻨﻌﺔا ﻣﺔﻟﴩا ﺑﻪ ﺻﺚوأ ﻣا ﻟﻬﺎدﻳﻌﺎ ﻣﺎ وأ ﻟﻨﯩﻊا ﺑﻨﻔﺲ ﻓﻘﻂ‬
‫ﻧﻌﺔﻟﺼﺎا ﻣﺔﻟﴩا تﻟﺤﻌﻠﻴا ﻓﻘﺎو ﳌﺴﺤﻌﻤﻠﺔا تﻳﺎرﻟﺒﻄﺎا ﻣﻦ ﺟﺨﻠﺺ‬
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제
조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용
된 배터리를 처리하여 주십시오.
Waarschuwing
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de batterij
slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen wordt. Gebruikte
batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd te worden.
Redundant Power Supplies
Warning! This unit might have more than one power supply connection. All connec tions must be removed to de-energize the unit.
冗長電源装置
このユニットは複数の電源装置が接続されている場合があります。
ユニットの電源を切るためには、すべての接続を取り外さなければなりません。
警告
此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。
警告
此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。
Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit
kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.
115
Appendix B: Standardized Warning Statements
¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación. Para cortar
por completo el suministro de energía, deben desconectarse todas las conexiones.
Attention
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute tension et tout
courant électrique de l'unité, toutes les connexions d'alimentation doivent être débranchées.
‫אם קיים יותר מספק אחד‬
!‫אזהרה‬
‫ יש להסיר את כל החיבורים על מנת לרוקן‬.‫ליחדה יש יותר מחיבור אחד של ספק‬
.‫את היחידה‬
. ‫قد يكون لهذا الجهاز عدة اتصاالت بوحدات امداد الطاقة‬
‫يجب إزالة كافة االتصاالت لعسل الوحدة عن الكهرباء‬
경고!
이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에 전원을
차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.
Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle aansluitingen dienen
verwijderd te worden om het apparaat stroomloos te maken.
116
WinFast GS2030 User's Manual
Backplane Voltage
Warning! Hazardous voltage or energy is present on the backplane when the system
is operating. Use caution when servicing.
バックプレーンの電圧
システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。
修理する際には注意ください。
警告
当系统正在进行时，背板上有很危险的电压或能量，进行维修时务必小心。
警告
當系統正在進行時，背板上有危險的電壓或能量，進行維修時務必小心。
Warnung
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche Spannungen
oder Energien auf. Vorsicht bei der Wartung.
¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso. Tenga
cuidado cuando lo revise.
Attention
Lorsque le système est en fonctionnement, des tensions électriques circulent sur le fond de
panier. Prendre des précautions lors de la maintenance.
‫יהאחור פנלב מתח‬
!‫זהרהא‬
‫ערכתהמ עולתפ זמןב יהאחור פנלב מתח סכנת קיימת‬. ‫במהלך להיזהר שי‬
.‫העבודה‬
117
Appendix B: Standardized Warning Statements
‫هناك خطز مه التيار الكهزبايئ أوالطاقة املىجىدة عىل اللىحة‬
‫عندما يكىن النظام يعمل كه حذرا عند خدمة هذا الجهاس‬
경고!
시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생 합니다.
서비스 작업 시 주의하십시오.
Waarschuwing
Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het systeem in
gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.
Comply with Local and National Electrical Codes
Warning! Installation of the equipment must comply with local and national electrical
codes.
地方および国の電気規格に準拠
機器の取り付けはその地方および国の電気規格に準拠する必要があります。
警告
设备安装必须符合本地与本国电气法规。
警告
設備安裝必須符合本地與本國電氣法規。
Warnung
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
¡Advertencia!
La instalacion del equipo debe cumplir con las normas de electricidad locales y nacionales.
Attention
L'équipement doit être installé conformément aux normes électriques nationales et locales.
118
WinFast GS2030 User's Manual
‫ציהאר החשמל חוקי יאוםת‬
!‫זהרהא‬
. ‫צייםוהאר המקומיים החשמל לחוקי תואמת להיות בתחיי הציוד קנתהת‬
‫ﳌﺘﻌﻠﻘﺔا ﻟﯩﻄﯩﻴﺔاو ﳌﺤﻠﻴﺔا ﻳﻪوﻟﻠﻘﯩﺎ مﺘﺜﻞ ﻧﺄ ﻳﺠﺐ ﺋﻴﺔﺑﺎﻟﻜﻬﺮا ﺗﺎﳌﻌﺪا ﻛﻴﺐ ﺗﺮ‬
‫ءﺑﺎﻟﻜﻬﺮﺑﺎ‬
경고!
현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.
Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale
elektriciteitsvoorschriften.
Product Disposal
Warning! Ultimate disposal of this product should be handled according to all national
laws and regulations.
製品の廃棄
この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要があります。
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes
erfolgen.
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos
nacionales.
119
Appendix B: Standardized Warning Statements
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou
directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
‫סילוק המוצר‬
!‫אזהרה‬
.‫סילוק סופי של מוצר זה חייב להיות בהתאם להנחיות וחוקי המדינה‬
‫التخلص النهايئ من هذا املنتج ينبغي التعامل معه وفقا لجميع القىانني واللىائح الىطنية عند‬
경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle
nationale wetten en reglementen.
Hot Swap Fan Warning
Warning! Hazardous moving parts. Keep away from moving fan blades. The fans might
still be turning when you remove the fan assembly from the chassis. Keep fingers,
screwdrivers, and other objects away from the openings in the fan assembly's housing.
ファン・ホットスワップの警告
警告！回転部品に注意。運転中は回転部(羽根)に触れないでください。シャーシから冷却ファン装
置を取り外した際、
ファンがまだ回転している可能性があります。ファンの開口部に、指、
ドライバ
ー、およびその他のものを近づけないで下さい。
警告!
警告！危险的可移动性零件。请务必与转动的风扇叶片保持距离。 当您从机架移除风扇装置，
风扇可能仍在转动。小心不要将手指、螺丝起子和其他物品太靠近风扇
警告
危險的可移動性零件。請務必與轉動的風扇葉片保持距離。 當您從機架移除風扇裝置，風扇可
能仍在轉動。小心不要將手指、螺絲起子和其他物品太靠近風扇。
120
WinFast GS2030 User's Manual
Warnung
Gefährlich Bewegende Teile. Von den bewegenden Lüfterblätter fern halten. Die Lüfter drehen
sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halten Sie
Finger, Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses
entfernt.
¡Advertencia!
Riesgo de piezas móviles. Mantener alejado de las aspas del ventilador. Los ventiladores
podran dar vuelta cuando usted quite ell montaje del ventilador del chasis. Mandtenga los
dedos, los destornilladores y todos los objetos lejos de las aberturas del ventilador
Attention
Pieces mobiles dangereuses. Se tenir a l’ecart des lames du ventilateur Il est possible que les
ventilateurs soient toujours en rotation lorsque vous retirerez le bloc ventilateur du châssis.
Prenez garde à ce que doigts, tournevis et autres objets soient éloignés du logement du
bloc ventilateur.
!‫זהרהא‬
‫מסוכנים עיםנ חלקים‬. ‫חלקי את יםמסיר שרעולהכאפב המאוורר מלהבי התרחק‬
‫מהמארז המאוורר‬, ‫יםדבעו ייןדע יםוהמאוורר כןית‬. ‫את טוחב למרחק קלהרחי שי‬
‫המאוורר בתוך מהפתחים שונים עבודה יוכל צבעותהא‬
‫ ﻧﺄ ﳌﻤﻜﻦا ﻣﻦ‬.‫ ﻛﺔ ﳌﺘﺤﺮا ﺣﺔوﳌﺮا ﺗﺎﺷﻔﺮ ﻋﻦ ﺑﺘﻌﺪا‬.‫ةﺧﻄﺮ ﻛﺔ ﻣﺘﺤﺮ ءاﺟﺰأ !ﯾﺮﺗﺤﺬ‬
‫ﺑﻊﺻﺎﻷا ءﺑﻘﺎإ ﯾﺠﺐ ﻟﮭﯿﻜﻞا ﻣﻦ ﺣﺔوﳌﺮا ﻛﺘﻠﺔ ﻟﺔازإ ﻋﻨﺪروﺗﺪ ﻻﺗﺰ ﻻ ﺣﻮاﳌﺮا‬
‫ ﺣﺔوﳌﺮا ﻛﺘﻠﺔ ﰲ تﻟﻔﺘﺤﺎا ﻋﻦ اﺑﻌﯿﺪ ءﺷﯿﺎﻷا ﻣﻦ ﮬﺎﻏﯿﺮو ﻏﻲاﻟﱪا تﻣﻔﻜﺎو‬.
경고!
움직이는 위험한 부품. 회전하는 송풍 날개에 접근하지 마세요. 섀시로부터 팬 조립품을
제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬 조림품 외관의 열려있는 부분들로부터
손가락 및 스크류드라이버, 다른 물체들이 가까이 하지 않도록 배치해 주십시오.
Waarschuwing
Gevaarlijk bewegende onderdelen. Houd voldoende afstand tot de bewegende ventilatorbladen.
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het ventilatorsamenstel
uit het chassis. Houd uw vingers, schroevendraaiers en eventuele andere voorwerpen uit de
buurt van de openingen in de ventilatorbehuizing.
121
Appendix B: Standardized Warning Statements
Power Cable and AC Adapter
Warning! When installing the product, use the provided or designated connection
cables, power cables and AC adaptors. Using any other cables and adaptors could
cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits
the use of UL or CSA -certified cables (that have UL/CSA shown on the code) for any
other electrical devices than products designated by Leadtek only.
電源コードとACアダプター
製品を設置する場合、提供または指定および購入された接続ケーブル、電源コードとACアダプター
を 該当する地域の条例や安全基準に適合するコードサイズやプラグと共に使用下さい。他のケー
ブルやアダプタを使用すると故障や火災の原因になることがあります。
電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表記)を Leadtek
が指定する製品以外に使用することを禁止しています。
警告
安装此产品时,请使用本身提供的或指定的或采购的连接线,电源线和电源适配器，包含遵照当
地法规和安全要求的合规的电源线尺寸和插头.使用其它线材或适配器可能会引起故障或火灾。
除了Leadtek所指定的产品,电气用品和材料安全法律规定禁止
使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。
警告
安裝此產品時,請使用本身提供的或指定的或採購的連接線,電源線和電源適配器，包含遵照當
地法規和安全要求的合規的電源線尺寸和插頭.使用其它線材或適配器可能會引起故障或火災。
除了Leadtek所指定的產品,電氣用品和材料安全法律規定禁止
使用未經UL或CSA認證的線材。 (線材上會顯示UL/CSA符號)。
Warnung
Nutzen Sie beim Installieren des Produkts ausschließlich die von uns zur Verfügung gestellten
Verbindungskabeln, Stromkabeln und/oder Adapater, die Ihre örtlichen Sicherheitsstandards
einhalten. Der Gebrauch von anderen Kabeln und Adapter können Fehlfunktionen oder
Feuer verursachen. Die Richtlinien untersagen das Nutzen von UL oder CAS zertifizierten
Kabeln (mit UL/CSA gekennzeichnet), an Geräten oder Produkten die nicht mit Leadtek
gekennzeichnet sind.
122
WinFast GS2030 User's Manual
¡Advertencia!
Cuando instale el producto, utilice la conexión provista o designada o procure cables, Cables
de alimentación y adaptadores de CA que cumplan con los códigos locales y los requisitos
de seguridad, incluyendo el tamaño adecuado del cable y el enchufe. El uso de otros cables
y adaptadores podría causar un mal funcionamiento o un incendio. La Ley de Seguridad de
Aparatos Eléctricos y de Materiales prohíbe El uso de cables certificados por UL o CSA (que
tienen el certificado UL / CSA en el código) para cualquier otros dispositivos eléctricos que
los productos designados únicamente por Leadtek.
Attention
Lors de l'installation du produit, utilisez les cables de connection fournis ou désigné ou
achetez des cables, cables de puissance et adaptateurs respectant les normes locales et
les conditions de securite y compris les tailles de cables et les prises electriques appropries.
L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement ou un
incendie. Appareils électroménagers et la Loi sur la Sécurité Matériel interdit l'utilisation de
câbles certifies- UL ou CSA (qui ont UL ou CSA indiqué sur le code) pour tous les autres
appareils électriques sauf les produits désignés par Leadtek seulement.
‫ אמיומת ייםחשמל יםלכב‬AC
‫!זהרהא‬
‫ צרהמו את קיניםמת שרכא‬, ‫יםלבכב שמלהשת שי‬, ‫ אמיםומת קיםספ‬AC
‫קנהההת צורךל אמוהות או נרכשו שרא‬, ‫שותילדר אמוהות שרוא‬
‫המקומיות טיחותהב‬, ‫ קעוהת להכב של נכונה מידה כולל‬. ‫ אחר מסוג אםמת או לכב בכל שימוש‬, ‫יחשמל קצר או קלהלת לגרום עלול‬. ‫אםבהת‬
‫טיחותהב וחוקי החשמל יבמכשיר השימוש לחוקי‬, ‫ ב המוסמכים יםלבכב שמלהשת איסור קיים‬- UL ‫ב או‬-CSA ( ‫קוד יהםעל עמופי שרכא‬
‫( של‬UL/CSA ‫ אחר יחשמל צרמו כל עבור‬, ‫י"ע אםהות שרא צרבמו רק לאא‬
Leadtek
‫דלבב‬.
‫ﳌﻨﺘﺞا ﻛﻴﺐ ﺗﺮ ﻋﻨﺪ‬، ‫ﻟﻚذ ﰲ مﺎ ﳌﺤﻠﻴﺔا ﻣﺔﻟﺴﻼا تﻣﺘﻄﻠﺒﺎو ﻧﻧﺎﺑﻘﻮ ﻣﺎﻟﺘﺰﻻا ﻣﻊ ددﳌﱰا رﻟﺘﻴﺎا تﻻﻣﺤﻮو ﺋﻴﺔﺑﺎﻟﻜﻬﺮا تﺑﻼﻟﻜﺎا ءاﺑﴩ ﻗﻢ وأ ةدﳌﺤﺪا وأ ةﻓﺮﳌﺘﻮا تﺻﻴﻼﻟﺘﻮا ﻣﺎﺳﺘﺨﺪﺑﺎ ﻗﻢ‬
‫ﻟﺴﻠﻴﻢا ﺑﺲﻟﻘﺎاو ﺻﻞﳌﻮا ﺣﺠﻢ‬. ‫ﻳﻖﺣﺮ وأ ﻋﻄﻞ ﰲ ﻳﺘﺴﺒﺐ ﻗﺪ ىﺧﺮأ تﻻﻣﺤﻮو تﺑﻼﻛﺎ ﻳﺄ ﻣﺎﺳﺘﺨﺪا‬. ‫ةﳌﻌﺘﻤﺪا تﺑﻼﻟﻜﺎا ﻣﺎﺳﺘﺨﺪا ﺗﺎﳌﻌﺪاو ﺋﻴﺔﺑﺎﻟﻜﻬﺮا ةﺟﻬﺰﻟﻸ ﻣﺔﻟﺴﻼا نﻧﻮﻗﺎ ﻳﺤﻈﺮ‬
‫ ﻗﺒﻞ ﻣﻦ‬UL ‫ أو‬CSA ‫( ﻣﺔﻋﻼ ﺗﺤﻤﻞ ﻟﺘﻲاو‬UL/CSA) ‫ﻗﺒﻞ ﻣﻦ ةدﳌﺤﺪاو ﳌﻌﻨﻴﺔا تﳌﻨﺘﺠﺎا ﻏر ىﺧﺮأ ﺗﺎﻣﻌﺪ ﻳﺄ ﻣﻊ‬
123
Leadtek.
Appendix B: Standardized Warning Statements
전원 케이블 및 AC 어댑터
경고! 제품을 설치할 때 현지 코드 및 적절한 굵기의 코드와 플러그를 포함한 안전 요구
사항을 준수하여 제공되거나 지정된 연결 혹은 구매 케이블, 전원 케이블 및 AC 어댑터를
사용하십시오.
다른 케이블이나 어댑터를 사용하면 오작동이나 화재가 발생할 수 있습니다. 전기 용품
안전법은 UL 또는 CSA 인증 케이블 (코드에 UL / CSA가 표시된 케이블)을 Leadtek
가 지정한 제품 이외의 전기 장치에 사용하는 것을 금지합니다.
Stroomkabel en AC-Adapter
Waarschuwing! Bij het aansluiten van het Product uitsluitend gebruik maken van de geleverde
Kabels of een andere geschikte aan te schaffen Aansluitmethode, deze moet altijd voldoen
aan de lokale voorschriften en veiligheidsnormen, inclusief de juiste kabeldikte en stekker.
Het gebruik van niet geschikte Kabels en/of Adapters kan een storing of brand veroorzaken.
Wetgeving voor Elektrische apparatuur en Materiaalveiligheid verbied het gebruik van UL of
CSA -gecertificeerde Kabels (met UL/CSA in de code) voor elke andere toepassing dan de
door Leadtek hiervoor beoogde Producten.
124
Appendix C: System Specifications
Appendix C
System Specifications
Processors
Dual Intel Xeon 81xx/61xx/51xx/41xx/31xx Series processors in a Socket P type socket
Note: Please refer to the motherboard specifications pages on our website for updates to supported processors.
Chipset
Intel PCH C621 chipset
BIOS
256 Mb SPI AMI® BIOS Flash ROM
Memory
Sixteen DIMM slots support up to 2TB of DDR4-2666 ECC 3DS LRDIMM or ECC RDIMM
Note: See the memory section in Chapter 3 for details and our website for updates to supported memory.
SATA Controller
On-chip (Intel PCH C621) controller
Drive Bays
Ten 2.5" hot-swap drive bays
PCI Expansion Slots
Up to seven PCI-E 3.0 slots (see table on page 12 for details)
Motherboard
X11DPG-SN; (13.1 x 14.7 in. / 333 x 373 mm.)
Chassis
SC218GHTS-R2K03BP3; 2U Rackmount, (WxHxD) 17.2 x 3.5 x 30.5 in. (437 x 89 x 775 mm)
System Cooling
Five 8-cm PWM fans
Power Supply
Model: PWS-2K03P-1R
AC Input Voltages: 100-240 VAC
Rated Input Current: 100-120V: 12.5A max., 230-240V: 10A max.
Rated Input Frequency: 50-60 Hz
Rated Output Power: 2000W
Rated Output Voltages: +12V (166.7A; +12Vsb (3.5A)
Operating Environment
Operating Temperature: 10º to 35º C (50º to 95º F)
Non-operating Temperature: -40º to 70º C (-40º to 158º F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5% to 95% (non-condensing)
125
WinFast GS2030 User's Manual
Regulatory Compliance
Electromagnetic Emissions: FCC Class A, EN 55032 Class A, EN 61000-3-2/3-3, CISPR 32 Class A
Electromagnetic Immunity: EN 55024/CISPR 24, (EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6,
EN 61000-4-8, EN 61000-4-11)
Safety: CSA/EN/IEC/UL 60950-1 Compliant, UL or CSA Listed (USA and Canada), CE Marking (Europe)
Other: VCCI-CISPR 32 and AS/NZS CISPR 32
Environmental: Directive 2011/65/EU and Directive 2012/19/EU
Perchlorate Warning
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products
containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/
hazardouswaste/perchlorate”
126

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project