RGBlink VSP3500 Quick Start Guide

RGBlink VSP3500 Quick Start Guide
VIEWSIZE THE WORLD
VSP 3500 – Quick Start
For full installation, configuration, and operation details, refer to the
VSP 3500 user manual, which is available at www.rgblink.com.
This guide provides quick start instructions for an experienced installer to set
up and operate the VSP 3500.
NOTE
Installation and cabling features
Rear Panel
Connections
1 Dial switch
2 10/100M Internet Control Port
3 USB Control Port
4 RS232 Control Port
5
6 DVI Loop Out
7
8
DVI Input Port DVI-I
9 ~ 12 DVI Output Port DVI-I
13 14 Power Switch Button
and Power Port IEC-3
Step 1-Mounting
Turn off or disconnect all equipment power sources.
Step 2- DVI Input DVI-I
DVI input ports support signal sources
of HDM I from high-definition player
or DVI from PC.
NOTE Comments to use the programs video when
connect with HDMI from high definition
player.
Step 3- DVI Loop Out
Can connect the next level VSP 3500
or the device with DVI loop out.
Step 4- DVI Output DVI-I
192.168.0.100. Operator can also change the IP address
by RS 232 or USB.
Twist CAT5 should be one end in T568A, and another
end in T568B standard.
Crossover Cable
Pins
Pin
End 1
Wire color
1
2
3
4
5
6
7
8
White-green
Green
White-orange
Blue
White-blue
White-orange
White-brown
Brown
End 2
Wire color
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Used to connect display system with
DVI input port or LED display control
Insert Twisted
system; DVI 1 output acts as the default
Pair Wires
RJ-45
program output.
Connector
T568A
T568B
NOTE Comments to use the sending cards box,
Driver, DV4 from RGBlink for that VSP3500 CAT5 is wired as T568A at one end and T568B at the
can not support sending card installed inside. other(Tx and Rx pairs reversed) is crossover.
Step 5- Lan Control Port
Step 6-USB Port
Use twist CAT5 cable to connect to LAN port, operator Use USB cable to connect the VSP 3500 and
computer.
can control VSP 3500 based on default IP address:
Address: S603~S604, Weiye Building, Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian, China
Tel: 00865925771197
Fax:00865925771202
Email: [email protected]
http://www.rgblink.cn
VSP 3500 Quick Start
Version 1.0
Page 1 of 4
Step 7- Serial Port
How to add layer
Use RS232 to RJ11 cable to connect a control system
or computer to the back panel RJ11 port and the other
end on RS232 port. RS232 to RJ11 cable as following
definition.
In LAYERS area, choose layer that need to increase
layer, that is press any key of layer A, B, C, D (or select
all the 4 keys), key lights, then the layer is selected, and
add layer finished.
Function
RS-422
Function
2
3
5
7
8
TX
RX
GND
-----
Transmit
Receive
Signal Ground
Not Used
Not Used
TXRXGND
RX+
TX+
Transmit(-)
Receive(-)
Signal Ground
Receive(+)
Transmit(+)
Pin
RJ-11
Function
1
2
3
4
--RX
TX
GND
Not Used
Receive
Transmit
Signal Ground
Pin RS-232
Insert Twisted
Pair Wires
RS232/RS422
Connector
How to clear layer
1. In LAYER area, press any key of layer A, B, C, D
that need to clear, key blinks,
2. Press the key again, key light is off, and clear layer
finished.
How to edit and define output
Insert Twisted
Pair Wires
RJ11 Connector
Step 8- Power Port
Plug in power cord which has IEC connector, VSP
3500 supports AC power from 90 to 264 VAC,5060Hz, which means world wide compatible.
Power On
1. In OUTPUTS part, push DVI1, DVI2, DVI3, DVI4
and it will light to show it is being programmed;
OUTPUTS part DVI1 key is correspond with DVI1;
OUTPUTS part DVI2 key is correspond with DVI2;
OUTPUTS part DVI3 key is correspond with DVI3;
OUTPUTS part DVI4 key is correspond with DVI4;
2. In FUNCTIONS part, push Scale to adjust the size
of image which means to zoom in/out of the image;
3. In CUSTOM ADJUSTMENTS part, push Crop to
crop the image which means to crop the input signal
of the output screen;
4. In CUSTOM ADJUSTMENTS part, push Position
to adjust the position of the corresponding input
image of the layer which means to adjust the
position of output screen.
Push power button switcher to ON position. LCD
module on the front panel will show RGBLINK and
VSP 3500 model information, and go into self
verification before it load the last setting configuration
data and send the processed image to the target display
or device. For the first time running, CV1 input is the How to scale the layer image
default input source.User can operate with VSP 3500
1. In CUSTOM ADJUSTMENTS area, press 【SCALE】
with local front panel and remote control with the
key, key lights, and start the scale function;
software run on the PC, remote control by RS232, USB 2. In LAYER area, press any bright key of A, B, C, D
or TCP/IP.
(light key among layer key is optional), key lights, and
Local Control-Front Panel Operation
it can be edited;
3. Rotate the up/down knob to adjust window width;
Rotate the left/right knob to adjust window height;
4. Press 【SCALE】 key again, key light is off, and
close the scale function.
How to set output resolution
How to crop the layer image
Press MENU button, and rotate Up/Down knob to
select OUTPUT CONFIG. Press NEXT and rotate
Up/Down knob to select OUTPUT FORMAT. Press
NEXT and rotate Left/Right knob to select OUTPUT
RESOLUTION. Then press NEXT to setup.
1. In CUSTOM ADJUSTMENTS area, press【CROP】
key, key lights, and start crop the layer image function;
2. In LAYER area, press any bright key of A, B, C, D
(keys light are optional ), key lights, and it can be edited;
3. Rotate left/right knob, and choose the menu options;
4. Rotate left/right knob, and adjust the optional value;
5. Press【CROP】key again, key light is out, and close
crop function.
NOTE VSP 3500 supports output resolution as
following:
1024×768×60Hz, 1280×720×60Hz,1280×768×60Hz,
1280×1024×60Hz,1360x768x60Hz,1366x768x60Hz, How to set the position of layer image
1400x1050x60Hz,1440x900x60Hz,1600×1200×60Hz, 1. In CUSTOM ADJUSTMENTS area, press 【Position】
1680x1050x60Hz,1920×1080×60Hz,1920x1200x60Hz,
key, key lights, and start the set the position of layer
2048x1152x60Hz;
image function;
Address: S603~S604, Weiye Building, Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian, China
Tel: 00865925771197
Fax:00865925771202
Email: [email protected]
http://www.rgblink.cn
VSP 3500 Quick Start
Version 1.0
Page 2 of 4
2. In LAYER area, press any bright key of A, B, C, D
(keys light are optional), key lights, and it can be
edited;
3. Rotate left/right knob to adjust window level
position, and rotate up/down knob to adjust window
vertical position;
4. Press 【Position】 key again, key lights is off and
close the set the position of layer image function.
How to achieve split function
Field glyph split on left side:
Total screen width is 5128, total screen height is1536,
the width of the first screen is1440, the height of the
first screen is 896.
Then Start X is 0, Start Y is 0.
Field glyph split on right side:
Total screen width is 5128, total screen height is1536,
the width of the first screen is1344, the height of the
first screen is 896.
Then Start X is1440+1632=3072, and Start Y is 0.
1. In SPLIT MODE area, press any key, key lights,
then start the output split function;
2. VSP 3500 provides 8 kinds of split modes for user,
rotate left/right knob to select the split mode
according to actual demand;
3. In OUTPUTS area, press any key of DVI1, DVI2,
DVI3, DVI4, select preset output, key lights, and it
is selected;
How to rotate layer image
4. In CUSTOM ADJUSTMENTS area, press
1. Press MENU key, choose 【LAYER CONFIG】
【 SCALE 】 key and 【 Position 】 key , key
option.
lights, user can set the size and position of output
2. Press NEXT, and enter to Layer A.
image;
3. Press NEXT again, and enter SET ROTATE.
5. Rotate left/right knob and up/down knob, user can
4. Press NEXT, choose SET ROTATE, rotate
set the size and position of output image;
LEFT/RIGHT knob to choose rotate mode.
6. In OUTPUTS area, press DVI1, DVI2, DVI3, DVI4
5.
LCD panel shows rotate mode, VSP 3500 provides
again, regulate the selected output, repeat step 4 and
2 kinds of rotate modes for user, that is image rotate
5 to complete regulation setting.
to left or right.
When VSP 3500 is in split mode, it only split
NOTE
Rotate effects setting is only for Layer A,
for A layer, and is invalid for other layers.
NOTE
and are invalid for other layers.
How to achieve quick split
There are single device split and multiple split modes, How to save the parameters
When VSP 3500 function setting is finished, VSP
specific operations are as follows:
3500 supports 10 saving modes to avoid resetting of
1. For multiple split mode, first press MENU button,
the same steps.
and choose “OUTPUT CONFIG” option, rotate
the knob, choose “EXTERNAL SYNC”. Note: If 1. Press 【SAVE】 key, key lights, and meanwhile
button 0~9 light, start the save option:
choose “EXTERNAL SYNC”, the output
2. Choose the corresponding position and save. SAVE
resolutions should be the same.
TO 1 ~SAVE TO 9 corresponding button 1~9,
2. Press any key in SPLIT MODE area, and choose
SAVE TO 10 corresponding button 0.
split modes.
3. Rotate the knob, choose “START X” and
How to load the saved parameters
“START Y” option (The horizontal starting
When VSP 3500 function setting is finished, VSP 3500
position and vertical starting position that current
device corresponding screen area in the entire LED supports 10 saved modes to avoid resetting of the same
steps. All those 10 save modes can be loaded to use.
display).
1. Press 【LOAD】 key, key lights, and meanwhile
4. Rotate the knob again to set “START X” and
button 0~9 light, start the load option:
“START Y”.
2. Choose the corresponding position and load. LOAD
5. When finish, press 【SAVE】 key to save.
FROM 1 ~LOAD FROM 9 corresponding button
Here we will take field glyph mode with two devices
1~9, LOAD FROM10 corresponding button 0.
for example:
Total screen width 5128, total screen height 1536, the NOTE Save 1 is the default mode for loading to
use when VSP 3500 is power on.
width of the four screens are 1440, 1632, 1344, 712,
and height is 896, 640, settings are as follows:
Address: S603~S604, Weiye Building, Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian, China
Tel: 00865925771197
Fax:00865925771202
Email: [email protected]
http://www.rgblink.cn
VSP 3500 Quick Start
Version 1.0
Page 3 of 4
Factory Reset: When there is wrong operation during
parameter adjustment, users can recall the device and
readjust the parameter. Following the steps: Press
MENU button ,choose the submenu Reset and press
NEXT to initiate factory reset.
FAQ solutions
Display has no output image
Assure there are input signals: Press【MENU】
and go into【Device Info】, press the knob to cofirm,
check the input signal sources, if appear <NO
INPUT>, please check the connection; If use PC DVI
or VGA as signal source, please set the display card
to dual display or expanding mode;
Assure there are output signals: Get a monitor with
VGA or DVI port, connect it to device output port,
see if the monitor can display normally. If unnormal,
check if the input signals are connected or if the
output cable contacts good.
Display blinks
Check if preview output is normal: Get a monitor
with VGA or DVI port and connect to the device
output port, check if the monitor displays normally;
If no blinks, check if DVI output plugs tight or
change the DVI cable that connects sending card, if
the monitor blinks, please check if input signal,
input connecting cable and input port are normal.
Display only shows part of the image
Scale the image: Press 【Scale】, rotate the knob to
adjust the size of screen, including width, height and
starting position, press 【Next】to confirm.
Display shows no bottom half part
Incorrect output resolution: Confirm the width and
height point on the screen, and select more adequater
resolution than screen width, press 【Next】 to
confirm.
Black edge appears on left or top
Adjust device DVI output DE excursion, press
MENU, select XY_POS, press the knob to confirm, if
LED screen top part appears black edge, adjust V_S
via rotate the knob; if LED screen left part appears
black edge, adjust H_S via rotate the knob. After
setting, please save the parameter to SAVE1.
All buttons light on together
Check if the dial switch is normal;
Power off the device, check if two red dial switches
on back left part of the device are all upwards, if not,
place them upwards, then power on the device again.
The red dial switches are mainly for upgrade.
Address: S603~S604, Weiye Building, Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian, China
Tel: 00865925771197
Fax:00865925771202
Email: [email protected]
http://www.rgblink.cn
VSP 3500 Quick Start
Version 1.0
Page 4 of 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement