Victron Energy Smart Battery Sense Owner Manual
Victron energy Smart Battery Sense:
Victron energy Smart Battery Sense is a wireless battery voltage-and-temperature sensor designed to optimize Victron MPPT Solar Charger parameters for improved battery charging efficiency and extended battery life. It connects wirelessly to compatible Solar Chargers using VE.Smart Network, a wireless technology based on Bluetooth Smart.
Key features:
- Monitors battery voltage and temperature
- Optimizes Solar Charger parameters for improved charging efficiency
- Extends battery life
- Wireless connectivity via VE.Smart Network
- Simple installation with inline fuse and pre-crimped eyelets
advertisement
ENGLISH
Smart Battery Sense Manual
29/09/2020
Smart Battery Sense Manual
Table of Contents
Smart Battery Sense Manual
1. Introduction
Smart Battery Sense is a wireless battery voltage-and-temperature sensor for Victron MPPT Solar Chargers.
The Solar Charger uses these measurements to optimize its charge parameters. The accuracy of the data it transmits will improve battery charging efficiency, and prolong battery life.
The connection between Smart Battery Sense and one or more Solar Charger(s) is wireless: It uses VE.Smart Network - a wireless technology based on Bluetooth Smart.
Simple to install & configure, Smart Battery Sense comes with an inline fuse and pre-crimped eyelets. Revealing the selfadhesive tape on the back allows you to mount it directly on the battery.
Product page on our main website: https://www.victronenergy.com/accessories/smart-battery-sense
When can I use Smart Battery Sense ...and when should I avoid using it?
• Check the VE.Smart Networking compatible products list for compatible Solar Chargers.
• Smart Battery Sense is not needed, or allowed, in systems which are already controlled by a Color Control GX or Venus GX, see FAQ Q6 for more info.
• Smart Battery Sense is not needed for installations which already have a BMV-712 (battery monitor) with a temperature sensor accessory.
• For installations using a BMV-702 together with its optional temperature sensor accessory - for wireless connectivity consider adding a VE.Direct Bluetooth Smart dongle instead of a Smart Battery Sense.
Page 1 Introduction
Smart Battery Sense Manual
2. Installation
Connect the two eyelets to your battery terminals and attach the unit directly onto the battery-body using its self-adhesive strip.
For banks of batteries Smart Battery Sense may be connected to any one of the individual batteries.
If the bat+ and bat- cables are not long enough they may be extended - only make sure you use the same, or a thicker, gauge of cable.
Page 2 Installation
Smart Battery Sense Manual
3. Configuration
This video will show you how to install Smart Battery Sense and includes step-by-step instructions for connecting it your mobile phone via VictronConnect VE.Smart Networking manual.
https://www.youtube.com/embed/v62wCfXaWXY
Page 3 Configuration
Smart Battery Sense Manual
4. LED Status codes
Smart Battery Sense has two LEDs: a Bluetooth status LED (blue), and an Error LED (red).
On power-up, the Bluetooth LED will be slow-blinking - indicating that the device is ready to accept a Bluetooth connection.
If both LEDs remain illuminated, something is wrong with the Smart Battery Sense unit (Hardware error).
When the LEDs are alternating quickly for more than 30 seconds, the Smart Battery Sense is in firmware update mode and will need to complete the update before it can be used. Firmware updates are performed (where necessary) after connecting to
VictronConnect.
Blue
LED
On
Red
LED
On
Smart
Battery
Sense state
Not functional
Connection
State
Disabled
Remark
Slow blinking
On
Off
Off
Measuring V/T
Measuring V/T
Not connected
Connected
Not connected
Hardware error.
Smart Battery Sense will not be visible in VictronConnect andit will not be contributing information to the VE.Smart
Network.
If VE.Smart Networking has been configured, the device will be contributing the voltage and temperature information to the VE.Smart network.
If VE.Smart Networking has been configured, the device will be contributing the voltage and temperature information to the VE.Smart network.
Red and Blue LED Alternating Fast blinking
On
On
Fast blinking
Slow blinking
Fast blinking
Firmware update
Firmware update
Firmware update
Connected
Programming
Page 4 LED Status codes
Smart Battery Sense Manual
5. Troubleshooting
See both the VictronConnect manual and the VE.Smart Network manual .
Page 5 Troubleshooting
Smart Battery Sense Manual
6. Technical product specification
Operation and Dimensions
Description
Dimension h x w x d (mm)
Cable length
Eyelet hole size
Fuse rating
Operating temperature range
Operating voltage range
Absolute maximum voltage
Bluetooth Frequency
Bluetooth Power
Value
14 x 38 x 38
45cm
10mm (M10)
T1A 250V
-10°C to +60°C
8V to 60V
65V
2402-2480MHz
-4dBm
Power consumption
BatteryVoltage
12 V
24 V
48 V
Not Connected
0.3 mA
0.2 mA
0.2 mA
Joining VE.Smart Network
0.5 mA
0.3 mA
0.3 mA
Connected
1.6 mA
0.9 mA
0.6 mA
Page 6 Technical product specification
advertisement