PowerG PG180DS 180W DETAIL SANDER Owner's Manual

TowerG
180W Detail Sander
PG180DS
vw
-»
a
Manufacturer: SUMEC Hardware & Tools Co., Ltd
1# Xinghuo Road, National level Nanjing High-Tech Zone,
Nanjing 210061 P.R. China
(em E
Pic.A
TECHNICAL DATA
Watts (Effective power)
No-load speed.
Detail Sander PG180DS
Rated voltage/ Frequency 230-240V~50Hz
Rated input power 180W
No-load speed 10000 rpm
Dimension 90*90*90mm
Protect electrical power tool from moisture!
Sound pressure level Lys =76 dB(A)
Koa=3,0 dB(A)
Power sound level
Lua =87 dB(A)
Kwa=3,0 dB(A)
Caution — electric shock!
Danger to life!
Vibration an =5.11 m/s?
K=1.5 m/s?
Protecting class
17 1
Check that the device, mains lead and plug are in good
condition!
DESCRIPTION OF SYMBOLS
Please read all of the safety and operating
instructions carefully before
using this tool. Please pay particular attention to all sections of this User
Guide that carry warning symbols and notices.
Safety class II
ОВ Ре =
Wear hearing protection, dust protection mask, protective
glasses and protective gloves.
e
li e
Dispose packaging and appliance in an environmentally
-friendly way!
Observe caution and safety notes!
Read instruction manual!
V
Voltage
GENERAL SAFETY INSTRUCTIONS
/\warnine
Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power
tool. Distractions can cause you to lose control.
1) Electrical safety
ZA To avoid danger to life from electric shock:
a) The mains plug on the device must match the mains socket.
The plug must not be modified in any way. Do not use an
adapter plug with devices fitted with a protective earth.
Unmodified plugs and matching sockets reduce the risk of electric
shock.
b) Avoid touching earthed surfaces such as pipes, radiators,
ovens and refrigerators with any part of your body. There is an
increased risk of electric shock if your body is earthed.
с) {= Keep the device away from rain or moisture. Water entering
an electrical device increases the risk of electric shock.
d) Do not use the mains lead for any purpose for which it was not
intended, e.g. to carry the device, to hang up the device or to
pull the mains plug out of the mains socket. Keep the mains
lead away from heat, oil, sharp edges or moving parts of the
device. Damaged or tangled mains leads increase the risk of
f)
2)
b)
d)
e)
f)
electric shock.
When working outdoors with an electrical power tool always
use extension cables that are also approved for use outdoors.
The use of an extension cable suitable for outdoor use reduces the
risk of electric shock.
Use a residual current device (RCD) for protection if operating
the electrical power tool in a moist environment is unavoidable.
The use of an RCD reduces the risk of electric shock.
Personal safety
Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in
serious personal injury.
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
Avoid unintentional operation of the device. Check that the
electrical power tool is switched off before you connect it to
the mains, pick it up or carry it. Accidents can happen if you carry
the device with your finger on the ON / OFF switch or with the
device switched on.
Remove any setting tools or spanners before you switch the
device on. A tool or spanner left attached to a rotating part of a
device can lead to injury.
Avoid placing your body in an unnatural position. Keep proper
footing and balance at all times. By doing this you will be in a
better position to control the device in unforeseen circumstances.
Wear suitable clothing. Do not wear loose clothing or jewellery.
g)
d)
f)
3)
b)
Keep your hair, clothing and gloves clear of moving parts.
Loose clothing, jewellery or long hair can become trapped in moving
parts.
If vacuum dust extraction and collection devices are fitted do
not forget to check that they are properly connected and
correctly used. The use of these devices reduces the hazard
presented by dust
Remove any adjusting key or wrench before turning the power
tool on. A wrench or a key left attached to a rotating part of the
power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected
situations.
Dress properly. Do not wear loose clothing or jewelry. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewelry or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and
properly used. Use of dust collection can reduce dust-related
hazards.
tool use and care
Do not force the power tool. Use the power tool correctly for
your application. The correct use will do the job better and safer at
the rate for which it was designed.
Do not use the power tool if the switch couldn’t on and off. Any
power tool that cannot be controlled with the switch is dangerous
and must be repaired.
Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of staring the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not
allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tool's operation. If damaged, have the
power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account the
working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result
In a hazardous situation.
SPECIAL SAFETY RULES FOR DETAIL SANDER
a) Securely support the workpiece. Use clamps or a vice to grip the
workpiece firmly. This is much safer than holding it in your hand.
b) Never support yourself by placing your hands near or in front of the
device or the workpiece surface. A slip can result in injury.
с) If a dangerous situation arises, pull the mains plug immediately out
of the mains socket.
d) Always work with the mains lead leading away from the rear of the
device.
e) Danger of fire from flying sparks ! Abrading metal creates flying
sparks. For this reason, always make sure that nobody is placed
in any danger and that there are no inflammable materials near the
working area.
f) A warning! Noxious fumes!
Any harmful / noxious dusts generated from sanding represent a
risk to the health of the person operating the device and to anyone
near the work area.
O0 Wear protective glasses and a dust mask!
g) When sanding wood and in particular when working on materials
that give rise to dusts that are hazardous to health, the sander must
be connected to a suitable external dust extraction device.
h) Ensure that there is adequate ventilation when working on plastic,
paint, varnish etc.
i) Do not soak the materials or the surface you are about to work on
with liquids containing solvents.
j) Do not abrade moistened materials or damp surfaces.
k) Avoid sanding paints containing lead or other substances
hazardous to health.
I) Do not work on materials containing asbestos. Asbestos is a known
carcinogen.
m) Avoid contact with the moving sanding sheet.
n) Operate the device only with an attached sanding sheet.
O) Never use the device for a purpose for which it was not intended nor
with non-original parts / accessories. The use of tools or
accessories other than those recommended in the operating
instructions could lead to you suffering an injury.
p) Switch the device off and allow it to come to a standstill before you
put it down.
q) Always keep the device clean, dry and free of oil or grease.
4) Service
a) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that the
safety of the power tool is maintained.
APPLICATION
Intended Use
The device is intended for dry sanding and polishing of wood, plastic,
metal, filler and painted surfaces. The device is particularly suitable for
corners, profiles
or difficult to access places. Any other use or modification to the device
shall be considered as improper use and could give rise to considerable
dangers. We will not accept liability for loss or damage arising from
Improper use.
Not suitable for commercial use.
Check the delivery parts
Carefully remove the machine from its packaging and check as the
following parts are complete:
--Detail sander
-- Dust extractor
--10pcs sanding sheets
--Operating instruction
If any parts are missing or damaged, please contact with your dealer.
10
11
Product Features
The numbering of the product features refers to the illustration of the
machine on the graphics page (Pic. A)
1 ON / OFF switch
2. Mains lead
3. Dust extraction spout
4. Adapter for external vacuum extraction
5. Backing plate
6. Soft grip
The accessories illustrated or described are not included as standard
delivery.
Operation
Take note of the mains voltage. The mains voltage at the mains socket
must match that shown on the rating plate on the device. Make sure that
the device is switched off before you connect it to the mains supply.
Note: Always switch on the delta sander before bringing it into contact
with the workpiece material.
Switching on the device
Press the ON / OFF switch 1 into setting “I”.
Switching off the device
Move the ON / OFF switch 1 into setting “0”.
Vacuum dust extraction
A warning ! Danger of fire!
There is the danger of fire when working with electrical devices that have
a dust box or can be connected to a vacuum cleaner. Under certain
conditions the wood dust in the dust extraction bag (or in the vacuum’
s dust bag) may ignite, e.g. as a result of flying sparks generated when
abrading metals or metal objects left in wood. This can happen
particularly if the wood dust is mixed with paint residue or other
chemicals and the abraded particles are hot from prolonged abrasion.
Therefore you must empty the device's dust collection box and the
vacuum cleaner’s dust bag before taking a break or stopping work and
always avoid overheating of the abraded particles and the device.
Wear a dust mask!
warning ! Always check that the mains plug is out of the socket
before doing any work on the device.
Adapter for external vacuum
Extraction Connection
Push the adapter 4 for external vacuum extraction into the dust
extraction spout 3 .When doing this observe the guide markings
on the device and adapter. Turn the adapter 4 to lock in place.
Removal:
Pull the adapter 4 for external vacuum extraction into the dust
extraction spout 3 .
Attaching / detaching sanding sheets
A Warning ! Always check that the mains plug is out of the socket
before doing any work on the device.
Attaching:
Put the Sanding sheet on the backing plate 5 and make sure they are
firmly stuck to backing plate.
Detaching:
Simply pull the sanding sheet off the backing plate.
Sanding and surfaces
The shape of the delta sander allows you to sand workpieces even in
12
13
their difficult to access places, corners and edges. Sanding performance
and surface quality depend on the grade of sanding sheet.
Always use sanding sheets with grades that are suitable for the
particular surface you are sanding. The speed selected should also be
appropriate to the task undertaken.
Advice on use
a) Switch the device on before placing it against the workpiece.
b) Apply light sanding pressure only.
c) Advance the device at an even rate.
d) Change sanding sheets at the appropriate time.
e) Do not work on different types of material using the same sanding
sheet (e.g. wood and then metal). To achieve the best sanding
results you should use unworn, undamaged sanding sheets.
f) Clean the sanding sheet from time to time with a vacuum cleaner.
Maintenance and cleaning
A Warning ! Always check the mains plug is out of the socket
before doing any work on the device.
The delta sander is maintenance-free.
a) Clean the device frequently. This should be done immediately after
you have finished using it.
b) For cleaning the housing use a dry cloth only.
c) Remove any adhering sanding dust with a narrow paint brush.
d) Never use any kind of sharp object or petrol, solvents or cleaning
agents that might attack plastic. Do not allow any liquids to enter the
inside of the device.
e) Always keep the ventilation slots clean.
Do not dispose of electrical appliances with your domestic waste!
1) The packaging
environmentally-friendly material. Dispose of it in your
comprises exclusively
local recycling containers.
2) Take the battery to your nearest authorized service center
or distributor that has been designated as a battery
recycling location.
Guarantee and Service
This product is guaranteed for 1 year from the original date of purchase,
the guarantee applies to material and production defects. This warranty
is not valid without the original dated receipt of purchase.
If the product shows defect as a result of material and production defects
during the period of guarantee, providing that the product has been used
properly and for the purpose which it has been intended, then faulty
products will either be replaced or refunded.
The guarantee does not cover accidental damage or misuse.
This product must be used in accordance with the instructions contained
In this manual.
The guarantee will be rendered invalid if the product has been damaged
by unauthorised repairs or resold.
Accessories are not covered by the guarantee.
If you have any problems or questions concerning the product, please
contact our customer helpline on 0844 856 0793.
14
15
SUMEC
Declaration of Conformity
We,
SUMEC Hardware & Tools Co.,LTD
1# Xinghuo Road, National level Nanjing High-Tech Zone,
Nanjing 210061 P.R. China
Declare that the product
Detail Sander
Model No. PG180DS
Complies with the essential safety and health requirement of the
following directives:
2006/42/EC
2004/108/EC
2006/95/EC
Standards and technical specification referred to:
EN55014-1:2006
EN55014-2:1997/+A1:2001
EN61000-3-2:2006
EN61000-3-3:1995/+A1:2001/+A2:2005
EN60745-1:2009
EN60745-2-4:2009
Authorized Signatory
Date: 01.01.2010
Signature:
Catv J Fhe
Name: Cai Jibo
General Manager
SUMEC Hardware & Tools Co..LTD
16
Ref. | Description Ref. | Description
1 Bearing 16 | Brush holder
2 Bevel Gearing 17 Brush bushing
3 | Shaft 18 | Carbon brush
4 Bearing 19 Bearing
5 Excentric block 20 Rotor
6 | Bearing 21 Bearing
7 Left housing 22 Bevel gear
8 Oscillating bracket 23 Rubber sleeve
9 Oscillating bracket 24 PCB
10 Induced draft pipe 25 Switch
11 | Soft pad 26 | Clip
12 | Tapping screw 27 | Tapping screw
13 | Hooky sanding pad 28 Cord sleeve
14 | Tapping screw 29 | Right housing
15 | Stator 30 Tapping screw
17
TowerG
Sumec Europe GmbH
Hanns-Martin-Schleyer-Str.18a
47877 Willich, Germany
Helpline: 0844 856 0793
180W Detail Sander
PG180DS