QUICK GUIDE

!

Visit website for available languages of this document.

LZR-WIDESCAN

Motion, Presence, and Safety Sensor for Industrial Doors

(US version)

READ BEFORE BEGINNING INSTALLATION & SET-UP

!

Refer to the user’s guide for safety instructions and supplemental information.

Do not remove the protection film during the mechanical adjustments.

Remove it before launching a teach-in.

Following installation, always test for proper operation before leaving the premises.

1

OPENING THE SENSOR

Make sure the cover is not locked (red cover lock).

Pull the two legs on top in order to open the cover.

Completely remove the cover before installing the sensor.

2

ADJUST SETTINGS (IF NEEDED)

a. Adjust the sensor before mounting for easier access to the LCD screen. b. Adjust the function and logic of the outputs only if required by your application. c. Open the USB cap and power the sensor using a mini USB charger or battery.

Adjustments may also be made after Teach-In, if not using the USB.

Ex:

Quick Start

In-Out

Motion

OUT 1

I/O

Motion or PC

Out1Logic

Motion detection or presence detection in pull-cord zone

OUT 2

Out2Logic

Out 2 Function

Pres or Sfty

Out 2 Logic

Presence detection of object in presence or safety field

RELAY

Out 2 Logic

RelayFunction

HeightTrigger

RelayLogic

Detection of object if height > 7 ft 4 in

NO

Out2Function

Normally open Out2Logic

RelFunction

NC

Normally open RelayLogic

De-energized

>More

De-energized in no detection

3

MOUNTING & WIRING

Install the sensor in the left corner or the center of the door as high as possible (max. 32’).

Field width and field stop are limited by the mounting height

(1:1.2). Sensor will adjust field sizes to the max possible value for the mounting height.

H a b

D

W

Verify if the angle lock screw is positioned as indicated.

Unscrew if necessary.

Remove the mounting bracket from the sensor and secure it to the wall. You can also install the sensor directly without using the mounting bracket.

c d

Position the sensor horizontally and secure the sensor to the mounting bracket.

Plug in the connector and pass the cable through the cable passage without making a loop.

OUT 1

*

RD

BK

YE

YE

POWER

SAFETY

OUT 2

*

RELAY

*

COM

NO

NC

PK

PK

PRESENCE

GN

WH-GN

GN-GREY

MOTION/PULL-CORD

BU

BU

TEST

Connect the wires accordingly.

* output status powered during non-detection with factory values

5

INSTALL

Launch teach-in after angle adjustment.

All presence/safety outputs are activated.

4

ANGLE ADJUSTMENT

Power the sensor. The LCD screen shows the detection display.

Activate the 2 visible laser spots by double-clicking OK or using the remote control sequence shown to the right.

The visible laser beams stay activated for 15 minutes or can be turned off by double-clicking OK or UNLOCK > MAGIC WAND > MAGIC WAND on the remote control.

Do not look directly into the laser emitter or the visible red laser beams.

Remove the blue protection film from the laser window.

F1

+

F2

C

D

PRESS

2X

OR

Make sure the curtain is parallel to the door by adjusting one or both screws on the side.

When the safety function is required, the red spots should be as close to the door as possible.

Negative angles reduce the depth of the detection fields.

Position the curtain closer to or farther away from the door by turning the screw at the top.

Launch the POSITION WIZARD to position the detection field correctly in front of the door.

LONG OK

1. Push and hold OK to launch the POSITION WIZARD.

2. Rotate the sensor in order to align the center of the red spots with the center of the door. Push OK.

3. Rotate the sensor until the LCD screen validates the position. Push OK to exit.

NOTE: It is best to make minor adjustments to the sensor and then verify that you are not obstructing the pattern. Verify that both red spots are on the floor with no interference.

Lock the sensor position by tightening the angle lock screw (see step 6A).

5

TEACH-IN: INSTALL

The teach-in zone (square in front of the 2 visible spots) should be completely free and flat.

This teach-in must be launched each time one of the sensor angles has been changed.

Make sure the protection film is removed and the cover is closed or removed.

1. Launch a teach-in by LCD or remote control (Quick Start > Teach-in > Install).

LCD

Quick Start

In-Out

QS

TeachIn

Presettings

TeachIn

Install

REMOTE

CONTROL

F1

+

F2

C

D

2. Clear the teach-in zone in front of the sensor.

The learning process starts. Position, angle, and height are learned; the background is analyzed and the teach-in ends successfully. If this is not accomplished, refer to the

TROUBLESHOOTING section in the User’s Guide (75.5916).

...

....

..

SETTINGS FOR 3 MAIN FUNCTIONS

MOTION WIDTH

000 – 460 inches

DEPTH

PRESENCE WIDTH

000 – 460 inches

DEPTH

SAFETY

WIDTH

000 – 460 inches

DEPTH

6 a

CLOSING THE SENSOR

b c

5

Lock the lateral angle by firmly fastening the angle lock screw.

Reclip the sensor cover horizontally and close it as indicated.

Lock the cover by turning the lock screw clockwise.

BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS

BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or inappropriate adjustments of the sensor/device; therefore,

BEA, Inc. does not guarantee any use of the sensor outside of its intended purpose.

BEA, Inc. strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/gates, and factory-trained for the type of door/gate system.

Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor system installation is compliant with local, national, and international regulations, codes, and standards.

Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer recommendations and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service call – examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107).

Verify that all appropriate industry signage and warning labels are in place.

Tech Support & Customer Service: 1-800-523-2462

General Tech Questions: [email protected] | Tech Docs: www.BEAsensors.com