Rosemount IO-Link USB Communicator Quick Start Guide
Rosemount IO-Link USB Communicator
This tool enables you to use sensors and actuators with an IO-Link interface (IO-Link devices).
Key features
- Adjust and observe IO-Link devices in a user-friendly and multilingual manner
- Pre-adjust, test, and demonstrate IO-Link devices
- Not intended for operations in manufacturing plants
Possible use cases
- Connecting to a PC via a USB cable
- Establishing an IO-Link connection using a standard 4- or 5-pin M12 patch cable
- Applying power supply via a USB port or an external wall power supply
- Monitoring the device status through light-emitting diodes (LEDs)
advertisement
Quick Start Guide
00825-0100-4115, Rev AB
May 2020
Rosemount
™
IO-Link USB Communicator
2
Quick Start Guide May 2020
Safety messages
WARNING
Installation considerations
Read this guide before working with the product. For personal and system safety, and for optimum product performance, ensure you thoroughly understand the contents before installing, using, or maintaining this product.Failure to follow these installation guidelines could result in death or serious injury. Use the equipment only as specified in this manual. Failure to do so may impair the protection provided by the equipment. Use the equipment only as specified. Failure to do so may impair the protection provided by the equipment. Ensure the device is installed by qualified personnel and in accordance with applicable code of practice. All operation described in this document must be carried out by authorized, trained personnel only.
Equipment modifications
Do not make changes to the source code or individual components. Changes such as this which are not explicitly stated in this document may forfeit any rights to technical support by the manufacturer.
Physical access
Unauthorized personnel may potentially cause significant damage to and/or misconfiguration of end users’ equipment. This could be intentional or unintentional and needs to be protected against.
Physical security is an important part of any security program and fundamental to protecting your system. Restrict physical access by unauthorized personnel to protect end users’ assets. This is true for all systems used within the facility.
Contents
Emerson.com/Rosemount
May 2020
1
Quick Start Guide
Overview
NOTICE
This guide provides basic guidelines for the Rosemount IO-Link USB
Communicator. It does not provide instructions for diagnostics, maintenance, service, or troubleshooting. This guide is available electronically on Emerson.com/Rosemount .
This tool allows you to apply sensors and actuators with an IO-Link interface
(IO-Link devices). The IO-Link devices are described by XML device descriptions so they can be adjusted and observed in a comfortable and multilingual manner. The tool serves for the pre-adjustment, test, and demonstration of IO-Link devices. The tool is not intended for operations in manufacturing plants.
Document purpose
This guide provides information required to install the Rosemount
Transmitter Interface Software.
Release information
Release date: June 1, 2020
Quick Start Guide 3
Quick Start Guide
2 Install hardware
May 2020
Procedure
1. Connect the PC to the USB IO-Link Master with the provided USB cable.
2. For connection of the interfaces to the IO-Link device, use a standard
4- or 5-pin M12 patch cable.
4 Emerson.com/Rosemount
May 2020
3
Quick Start Guide
Connections
Table 3-1: IO-Link connection
M12 (a-Coded connector) interface to the sensor with IO-Link
4
5
2
3
Pin
1
Signal
+24 V
IO-Link
GND
-
IO-Link
Function
+24V 1 A / 80 mA
IO-Link
0 V
IO-Link
NC
Table 3-2: USB connection
4
5
2
3
Pin
1
Signal
+5 V
D-
D+
ID
GND
Function
VBUS +5VDC/500 mA
Data -
Data +
Not connected
Ground
Quick Start Guide 5
Quick Start Guide May 2020
Pin
1
2
3
Table 3-3: Power supply
A USB port provides as standard 500 mA with 5 V . Without wall power supply the IO-
Link Master provides approximately 80 mA with 24 V . Therefore, many IO-Link devices can be used. If the IO-Link device requires more current, the wall power supply must be used. The pin assignment is demonstrated below.
Signal
+24 V
GND
GND
6 Emerson.com/Rosemount
May 2020 Quick Start Guide
4 Reference information
4.1
Light emitting diodes
The colors and definitions of the light emitting diodes on the USB IO-Link
Master are listed below.
Inscription
PWR
CH1(C/Q)
CH2(DI/DO)
Error
Color
Yellow
Definition
Indicates power supply at the USB port
Green/yellow Green: IO-Link mode
• LED blinks slowly if no IO-Link connection
• LED blinks quickly in pre-operate state
Yellow
Red
• LED constantly lit if IO-Link connection is active (operate state)
Yellow: SIO mode (indicates digital state at port
C/Q)
Indicates the digital state at port DIO
Flashes in case of errors (e.g. short circuit, errors in data transmission)
4.2
Dimensions
Quick Start Guide 7
*00825-0100-4115*
Quick Start Guide
00825-0100-4115, Rev. AB
May 2020
Global Headquarters
Emerson Automation Solutions
6021 Innovation Blvd.
Shakopee, MN 55379, USA
+1 800 999 9307 or +1 952 906 8888
+1 952 204 8889
Latin America Regional Office
Emerson Automation Solutions
1300 Concord Terrace, Suite 400
Sunrise, FL 33323, USA
+1 954 846 5030
+1 954 846 5121
Asia Pacific Regional Office
Emerson Automation Solutions
1 Pandan Crescent
Singapore 128461
+65 6777 8211
+65 6777 0947
Linkedin.com/company/Emerson-
Automation-Solutions
Twitter.com/Rosemount_News
Facebook.com/Rosemount
Youtube.com/user/
RosemountMeasurement
North America Regional Office
Emerson Automation Solutions
8200 Market Blvd.
Chanhassen, MN 55317, USA
+1 800 999 9307 or +1 952 906 8888
+1 952 204 8889
Europe Regional Office
Emerson Automation Solutions Europe
GmbH
Neuhofstrasse 19a P.O. Box 1046
CH 6340 Baar
Switzerland
+41 (0) 41 768 6111
+41 (0) 41 768 6300
Middle East and Africa Regional Office
Emerson Automation Solutions
Emerson FZE P.O. Box 17033
Jebel Ali Free Zone - South 2
Dubai, United Arab Emirates
+971 4 8118100
+971 4 8865465
© 2020 Emerson. All rights reserved.
Emerson Terms and Conditions of Sale are available upon request. The Emerson logo is a trademark and service mark of Emerson Electric
Co. Rosemount is a mark of one of the Emerson family of companies. All other marks are the property of their respective owners.
advertisement
Related manuals
advertisement