Chicago Electric 65939 Owner's manual

Chicago Electric 65939 Owner's manual
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
REV 16c
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Important SAFETY Information
Assembly Precautions
1. Assemble only according to these instructions.
Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under
the influence of drugs or medication.
6. To prevent explosion, do not fill
the tires above 40 PSI.
Use Precautions
1. Avoid working alone. If an accident
occurs, an assistant can get help.
8. Store and use this cart only on flat and level surfaces.
9. After welding, make sure gas valves
are securely tightened.
2. This product is not a toy. Do not allow
children to play with or near this item.
3. Use as intended only.
4. Always store acetylene and oxygen tanks away
from flammable materials and heat sources.
5. Inspect before use; check welds for cracks.
6. Wear the proper face mask and
gloves for welding purposes.
7. Make sure tanks are securely strapped to the cart.
10. Read and understand the warnings and
instructions provided by the manufacturer
of the welding equipment being used.
11. Maintenance should be performed
by a qualified technician.
12. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
document including all text under subheadings therein before set up or use of this product.
Tank Frame (4)
Handle
(1)
Tank
Frame (4)
Tool
Tray (3)
Axle
Brackets (7)
Axle
Brackets (7)
Bottom
Tray
Tool Tray
Bracket
(2)
Axle (6)
Baffle
Board (11)
Figure A
1. Start with the welded Tank Frame (4) as
this is where everything else attaches.
Page 2
Figure B
2. Line up the holes of the Handle (1) and
the Tool Tray Bracket with the holes at the
upper sides of the Tank Frame (4).
For technical questions, please call 1-888-866-5797.
Item 65939
3. Fit two Screws (9) through the holes in the Handle
(from the outside in), Tank Frame side, and the
Tool Tray Brackets on the inside of the Tank
Frame, and screw on two Washers and Nuts.
6. The Axle (6) is attached to the back-bottom
of the Tank Frame with two U-Bolts and four
washers and nuts onto the Axle Bracket (7).
a. There are two mounting height available:
4. Repeat for the other side.
• Upper mounting position - The Wheels
should be slightly off the ground when
the Cart is standing straight up.
a. When attaching the second Tool Tray
Bracket, slide the Tool Tray (3) onto
the metal pegs on the Brackets. These
Brackets hold the Tool Tray in place.
• Lower mounting position - The wheels are
always on the ground supporting the cart.
b. The Tool Tray should be able to
swing freely as the cart is tilted.
7. Check all screws and nuts making sure
they are tightly fastened and secure.
5. Slide the Wheels (5) onto the Axle ends and
secure in place with washers and split keys.
Maintenance
1. Periodically check welds for cracks
and for loose parts or damage.
3. Lubricate wheels if they begin to bind or squeak.
2. Check wheel tightness and tire pressure. To prevent
explosion, do not fill the tires above 40 PSI.
4. Keep dry and free of rust.
Storage and Safety Precautions
1. Store tanks away from heat and ignition sources.
4. Store and use on flat, level, hard surface.
2. Consult gas supplier on safest way
to transport and store gases.
5. When done welding, check that all
gas valves are closed tightly.
3. Cart is designed for a maximum of 48" tanks.
Parts List
Part
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Description
Handle
Tool Tray Bracket
Tool Tray
Tank Frame
Wheels (40 PSI)
Axle
Axle Bracket
U-Bolt
Screws (2" x 3/16")
Hex Screw
Baffle Board
Qty.
1
2
1
1
2
1
2
2
4
2
1
Record Serial Number Here:
Note:
If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Item 65939
For technical questions, please call 1-888-866-5797.
Page 3
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement