Owner’s Manual &

Safety Instructions

18h

Model

HA71

PROFESSIONAL ROLLING MITER SAW STAND

WARNING: To prevent serious injury, User must read and understand Owner’s Manual. SAVE THIS MANUAL

.

When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call

1-888-866-5797 as soon as possible. Reference 64751

IMPORTANT SAFETY INFORMATION

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

1.

PRIOR TO USING THIS PRODUCT, READ

AND UNDERSTAND ALL INSTRUCTIONS

AND SAFETY PRECAUTIONS AS OUTLINED

IN THE MANUFACTURER’S MANUAL OF

THE MITER SAW THAT IS TO BE USED.

2.

MAKE SURE THE MITER SAW STAND IS

PLACED ON A FLAT, LEVEL, HARD SURFACE

CAPABLE OF SUPPORTING THE WEIGHT

OF THE MITER SAW STAND, MITER SAW

BEING USED, AND WORKPIECE.

3.

BOLT THE MITER SAW SECURELY TO

THE MOUNTING BRACKETS ON THE

MITER SAW STAND AND TEST WORK SET-

UP FOR STABILITY BEFORE USE.

4.

KEEP ALL GUARDS IN PLACE

AND IN WORKING ORDER.

5.

MAKE SURE THE WORKPIECE IS SUPPORTED

AT ALL TIMES DURING OPERATION.

Use the two Extension Arms with longer wood stock if necessary.

6.

UNPLUG THE MITER SAW FROM ITS

ELECTRICAL SUPPLY SOURCE BEFORE

PERFORMING ANY SERVICE OR MAINTENANCE

ON THE MITER SAW STAND.

Make sure to unplug the Miter Saw before leaving the work area, moving the Miter Saw Stand from one location to another, cleaning sawdust from the unit, etc.

7.

Wear ANSI-approved safety goggles during assembly and use.

8.

Do not exceed listed weight capacity. Be aware of dynamic loading!

Sudden load movement may briefly create excess load causing product failure.

9. Weight capacity and other product capabilities apply to properly and completely assembled product only.

10. When folding or unfolding the Miter Saw

Stand, be careful not to pinch fingers.

11. This product is not a toy.

Do not allow children to play with or near this item.

12. Use as intended only.

13. Keep hands clear of moving parts.

14. Maintain labels and nameplates on the tool.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

15. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

16. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

Page 2

For technical questions, please call 1-888-866-5797.

Item 64751

Vibration Safety

This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury:

1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible.

2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury.

3. Use tools with the lowest vibration when there is a choice between different processes.

4. Include vibration-free periods each day of work.

5. Grip workpiece as lightly as possible (while still keeping safe control of it). Let the tool do the work.

6. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately.

SAVE THESE INSTRUCTIONS.

Maximum Load

Maximum Extension

Wheel Diameter

Specifications

550 lb

98-1/2"

8"

Item 64751

For technical questions, please call 1-888-866-5797.

Page 3

SETUP - BEFORE USE

this manual including all text under subheadings therein before set up or use of this product.

Read the ENTIRE IMPORTANT SAFETY

INFORMATION section at the beginning of

Note:

For additional information regarding the parts listed in the following pages, refer to

Parts List and Diagram

on page 10.

Set Up

1. Lay the Stand upside down on the floor.

2. Press the Lock Pin Handle on one leg and lift the leg up until Lock Pin engages.

3. Repeat with other legs.

Lock Pin

Handle

Assembly

1. Attach Wheel Base using four Bolts (56),

Washers (57) and Nuts (38).

Nut

(38)

Washer

(57)

Wheel

Base

Bolt

(56)

2. Insert Axle into Wheel Base.

3. Secure Wheel to Axle using one Washer (54),

Washer (81) and Lock Nut (48).

4. Repeat on other side.

Washer

(81) Washer

(54)

4. Turn Stand to upright working position and make sure all Lock Pins are engaged and legs are stable.

5.

Level Stand:

If necessary, turn

Adjustable Foot to level Stand.

Axle

Lock Nut

(48)

Wheel

5. Slide Handle over tubes and secure with two Bolts (37) and Nuts (38).

6. Slide Workpiece Support into end of Extension Arm.

7. Thread Set Screw (28) into bottom of Workpiece Support.

8. Repeat on other side.

Workpiece

Support

Extension

Arm

Set

Screw

(28)

Adjustable

Foot

Bolt

(37)

Nut

(38)

Handle

Page 4

For technical questions, please call 1-888-866-5797.

Item 64751

9.

Attaching Mounting Brackets:

a. Push in Lock Button.

b. Lift Lock Handle.

Lock

Button

Lock

Handle

c. Measure distance between mounting holes on saw (sold separately).

d. Place Right Mounting Bracket in Guide Bracket.

e. Push Lock Handle down until

Lock Button clicks in place.

f. Place Left Mounting Bracket so that it lines up with distance between mounting holes on saw.

g. Push Lock Handle down until

Lock Button clicks in place.

h. Move Mounting Nuts as necessary to fit the mounting holes on saw.

Note:

Move Guide Bracket as necessary to fit the saw.

Mounting

Nuts

10.

Mounting saw:

CAUTION!

Unplug saw before mounting it.

a. Place saw on Mounting Brackets.

b. Secure saw with four Bolts (27),

Spring Washers (26) and Washers (25).

WARNING!

Included Bolts may be too long or short for your miter saw. They must properly secure the miter saw to the brackets, thread all the way through the washers and nut, and not interfere with the safe operation of the saw in any way.

Replacement bolts can be used instead, but they must be grade 5, have the same head type and size as the included Bolts, and have a 1.25mm thread pitch and M8 thread diameter.

They also must properly secure the miter saw to the brackets, thread all the way through the washers and nut, and not interfere with the safe operation of the saw in any way.

Bolt

(27)

Spring

Washer

(26)

Washer

(25)

Saw sold separately

Guide

Bracket

11.

Removing saw:

The saw may be removed while attached to Mounting Brackets.

a. Push in Lock Buttons and lift Lock Handles.

b. Lift the saw off of the Stand.

12.

Replacing saw while attached to Mounting Brackets:

a. Push in Lock Buttons and lift Lock Handles.

b. Place Right Mounting Bracket in Guide Bracket.

c. Push Lock Handles down until

Lock Buttons click in place.

Item 64751

For technical questions, please call 1-888-866-5797.

Page 5

OPERATION

Read the ENTIRE IMPORTANT

SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY: Read the miter saw manufacturer’s instruction manual before use. Ensure that the miter saw is firmly secured to the stand. Use as a miter saw stand only – do not use with any other type of power tool. Do not exceed listed weight capacity. Do not use on uneven or slippery surfaces.

Adjusting Extension Arms

1. Raise Locking Handle, then pull out or push in Extension Arm to desired length.

2. Lower Locking Handle.

Extension

Arm

Locking

Handle

Adjusting Workpiece Supports

1.

Workpiece Height:

a. Loosen Lock Knob.

b. Raise or Lower Workpiece Support.

c. Tighten Lock Knob

2.

Workpiece Stop:

Use when cutting multiple workpieces the same length.

CAUTION!

Do not use both Workpiece Stops at the same time or saw blade may bind in the workpiece when cutting.

Roller Stop

Workpiece

Stop

Lock

Knob

Storage

1. Loosen Lock Knob and raise

Workpiece Support all the way.

2. Tighten Lock Knob.

Storage

Feet

3. Tip Stand so that it is resting on Storage Feet.

4. Press the Lock Pin Handles on each Leg and fold them in.

5. Roll Stand to storage area.

Page 6

For technical questions, please call 1-888-866-5797.

Item 64751

MAINTENANCE

Procedures not specifically explained in this manual must be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM

ACCIDENTAL OPERATION:

Turn the power switch of the miter saw mounted on the Miter Saw Stand off, and unplug the tool from its electrical outlet before performing any procedure in this section.

TO PREVENT SERIOUS INJURY FROM TOOL

FAILURE:

Do not use damaged equipment.

If abnormal noise or vibration occurs, have the problem corrected before further use.

1.

BEFORE EACH USE,

inspect the general condition of the Stand. Check for:

• loose hardware

• misalignment or binding of parts

• cracked or broken parts

• loose or improper mounting of the miter saw

• any other condition that may affect its safe operation.

2.

AFTER USE,

wipe external surfaces of the Stand with clean cloth.

3. Periodically, lightly lubricate all moving parts of the Stand.

Item 64751

For technical questions, please call 1-888-866-5797.

Page 7

Record Product’s Serial Number Here:

Note:

If product has no serial number, record month and year of purchase instead.

Note:

Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Parts may not be interchangeable. Specify item number when ordering.

Page 8

For technical questions, please call 1-888-866-5797.

Item 64751

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Item 64751

For technical questions, please call 1-888-866-5797.

Page 9

PARTS LIST AND DIAGRAM

Parts List

Part Description

1 Extension Arm

2 Spring

3 Steel Lock

4 Steel Sleeve

5 Lock Knob

6 Ф4 Spring

7 Ф4*8 Rivet

8 Cap

9 Mounting Bracket

10 Square Nut M8

11 M6*55 Bolt

12 Lock Handle

13 Spring

14 Mounting Bracket Base

15 Lock Mechanism

16 Ф5*60 Spring Pin

17 Lock Button

18 M6 Cover Nut

19 Cam

20 Clamp

21 Adjustable Clamp

22 Washer

23 Nut M6

24 Bolt M6*30

25 Ф8 Washer

26 Ф8 Spring Washer

27 Bolt M8*50

28 Set Screw M5*10

29 Bolt M6*45

30 Ф6 Spring Washer

31 Ф6 Washer

32 Extension Arm Base

33 Extension Arm Lock

34 Locking Handle

35 Bolt M6*12

36 Handle

37 Bolt M6*35

38 Nylon Nut M6

39 Worktop Support (Handle side)

40 Fixed Plate for the Worktop Support

41 Bolt M8*10

Qty

2

4

6

2

8

2

4

2

4

2

2

2

2

2

2

2

6

4

4

2

2

4

2

2

6

4

2

2

4

2

6

4

2

2

4

6

1

1

2

4

9

Part Description

42 Square Nut M6

43 Handle

44 Bolt M6*20

45 Carriage Bolt M8*50

46 Round Washer

47 Washer

48 Lock Nut M8

49 Limited Block Base

50 Guide Bracket

51 Worktop Support (Wheel side)

52 Wheel

53 Wheel Axle

54 Ф12 Washer

55 Wheel Base

56 Bolt M6*15

57 Ф6 Washer

58 Leg Cover

59 Ф4*10 Rivet

60 Leg

61 Lock Pin Handle

62 Ф6 Ring

63 Spring

64 Lock Pin

65 Extension Tube Lock Spring

66 Adjustable Foot

67 Adjustable Leg Sleeve

68 Adjustable Leg

69 Roller Cap

70 Roller Spring

71 Roller Axle

72 Roller

73 End Cap 20*20

74 Workpiece Stop

75 Frame End Cap 35*35

76 Workpiece Support (Wheel side)

77 Workpiece Support (Handle side)

78 Beam

79 Insert

80 Extension Lock Collar

81 Ф8 Washer

Qty

8

1

2

1

1

1

1

4

4

3

2

4

8

2

1

4

6

1

1

4

2

1

4

4

8

3

4

4

2

4

2

2

2

2

1

2

2

1

1

2

Page 10

For technical questions, please call 1-888-866-5797.

Item 64751

Assembly Diagram

Item 64751

For technical questions, please call 1-888-866-5797.

Page 11

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

For technical questions, please call 1-888-866-5797

Copyright

©

2018 by Harbor Freight Tools

®

. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797